Appendix E Catalogues
-
Upload
pham-dang-minh -
Category
Documents
-
view
115 -
download
5
description
Transcript of Appendix E Catalogues
-
Granted MITI Subsidy for Research and Development of Important Technologies in JapanAwarded "Best Energy Saving Product of 1979" in Japan
Features
October 2013 Revised PT9201E-1310-ver2.3
TOKYO OFFICEBeside Kiba, 2-17-16, Kiba, Koto-ku, Tokyo, 135-0042, JapanTEL:+81-3-5875-8842 FAX:+81-3-5875-8844
Website: http://www.jic-bestork.co.jp/ATTENTION7KHFRQWHQWVRIWKLVSDPSKOHWPD\EHFKDQJHGZLWKRXWSULRUQRWLFH,QDGGLWLRQUHSURGXFWLRQRUWUDQVPLVVLRQRIDQ\SDUWRIWKH contents without permission is prohibited.This catalog introduces products for the Japanese market. Use of the products in any country other than Japan is limited in a variety of ways.
Non-combustible material under Construction Ministry in JAPANNotification No. 1400 in 2000
For insulation thicker than specification, combine multiple boards/covers in layers. The dimensions of arch and elbow covers are specified elsewhere. Custom-manufacturable in other dimensions and shapes.
Thickness of thermal insulation comparison with the other calcium silicate thermal insulation material
Standard dimensions [mm] Standard performance
Calcium silicate thermal insulation material JIS A 9510 Type. 1-15-certified product
DAIPALITE is an ultra-light, Xonotlite-based thermal insulation material. This product features superior energy-saving performance as an industrial
thermal insulation material for piping, drying furnaces, tower tanks, and other types of tanks in various industrial facilities including plant complexes and power
generation facilities. It is also usable as a superior energy-saving back-up material for furnace building purposes and as a heat insulation material for construction
purposes.Available in forms of pipe cover, board, ARCH-COVER, etc. to suit the shape of the
surface to be thermally insulated.
Extremely light in weight with specific gravity of 0.13, hence highly portable and workable, and sure to help work efficiency dramatically.
Superior in thermal insulation than JIS type 2 products and sure to save energy greatly.Many advantages will occur, including reduced CO2 emissions.
1. Ultra-light weight
2. Superior energy-saving effect
Water-repellent treatment is available for DAIPALITE upon request.
Conditions In the same heat loss condition less than 122W/mPipe diameter = 140mm inside temp. = 300
About the performance of the thermal conductivity, JIS2-22 grade is close to the ASTM type.
250 50 75 100 125 150 mm
JIS 2-22 ASTM type
Thickness20%off
1 At 5% deformation.2 At maximum use temperature.3 For a board thickness of 25mm only, the density is 135 av.4 Only WPA type is 40 av.7KHUPDOFRQGXFWLYLW\RI'$,3$/,7(5HJUHVVLRQHTXDWLRQZLWKWHPSHUDWXUH:P.>@0.04070.000128>@0.05552.0510-51.9310-7
Density
Use temperature
Bending Strength
Compressive Strength*1
Heating linear shrinkage*2
100 38200 93
300 149400 204500 260600 316700 371800 427900 482
1000 538 W/mK 0.122 max.
0.102 max.
0.095 max.
0.087 max.
0.079 max.
0.072 max.
0.065 max.
0.059 max.
2 max.
68.8 min.
34.4 min.
240 max.
649 max.1000 max.
0.101 max.
0.097 max.
0.092 max.
0.088 max.
0.084 max.
0.078 max.
0.072 max.
2 max.
68.8 min.
34.4 min.
352 max.
649 max.
0.101 max.
0.097 max.
0.092 max.
0.088 max.
0.084 max.
0.078 max.
0.072 max.
2 max.
68.8 min.
34.4 min.
352 max.
927 max.
0.111 max.
0.108 max.
0.105 max.
0.110 max.
0.099 max.
0.090 max.
0.081 max.
0.074 max.
0.067 max.
0.060 max.
0.053 max.
0.046 max.
2.0 max.
45 av.*4
30 av.
130 av.*3
W/mKW/mKW/mKW/mKW/mKW/mKW/mKW/mKW/mK
N/2N/2Kg/m3
DAIPALITE Type TypeA Type
JIC
0.122 max.
1000 max.
0.110 max.
0.099 max.
0.090 max.
0.081 max.
0.074 max.
0.067 max.
0.060 max.
0.053 max.
0.046 max.
2.0 max.
30 min.
20 min.
155 max.
5HIHUHQFH$670&VWDQGDUG
Thermal Conductivity
Unit5HIHUHQFH
JIS 1-15standard
0.136 max.
650 max.
0.123 max.
0.111 max.
0.101 max.
0.091 max.
0.084 max.
0.077 max.
0.071 max.
0.064 max.
0.058 max.
2.0 max.
45 min.
30 min.
220 max.
5HIHUHQFH JIS 2-22standard
Internal Diameter 22~1300
304050
6575
25304050
6575100
150610300610610610150914300914610910
914
Thickness
Width
Length
Pipe cover Board
-
Combination of thermal insulation's thickness
-
DAIPALITE 03E-7
1/5
Date of preparation: September 30, 2009 Date of revision: October 28, 2013
Safety Data Sheet [Product name] DAIPALITE 1. Identification of the Product and of the Company [Product name] DAIPALITE [General name] Calcium Silicate Thermal Insulation [Company information] Company name : Japan Insulation Co., Ltd. Address : 4064-1, Azakitanuma, Nodashinden, Mizuho city, Gifu prefecture Section in charge : Quality Control Section, Manufacturing Division Telephone No. : +81-58-326-3221 FAX : +81-58-326-8982
2. Hazards Identification Contact of eyes and skin with this product may cause irritation of eyes and skin. Long term inhalation of this
product (particulates) may affect respiratory tract.
GHS classification (Crystalline silica) Physical and chemical hazards : None Human health hazards
Carcinogenicity : Class 1A Specific target organ/systemic toxicity (single exposure) : Class1 (Respiratory system) Specific target organ/systemic toxicity (repetitive exposure) : Class 1 (Respiratory system, Kidney)
Environmental effects : None
Label elements Crystalline silica Pictorial indication or symbol : Health hazards
Term calling for attention : Danger Hazard information : Respiratory system disorder Respiratory system or renal disorder caused by long-term
or repetitive exposure GHS classificationIron oxide
Physical and chemical hazards : None Human health hazard
Skin corrosivityIrritating property : Class 2 Serious damage to eyesIrritating property : Class 1 Specific target organ/systemic toxicity (single exposure) : Class 3respiratory tract irritation Specific target organ/systemic toxicityrepetitive exposure : Class 1 (Respiratory system)
Environmental effects : None
Label elements Iron oxide Pictorial indication or symbol : Exclamation mark, Corrosivity, Health hazards
Term calling for attention : Warning, Danger Hazard information : Irritating property to skin Serious damage to eyes
Respiratory tract irritation May cause irritation to respiratory system
Disorder of organs (metabolic system) caused by long-term or repetitive exposure
-
DAIPALITE 03E-7
2/5
GHS classificationSilicon carbide Physical and chemical hazards : None Human health hazards
Carcinogenicity : Class 2 Specific target organ/systemic toxicity (single exposure) : Class1 (Respiratory system) Specific target organ/systemic toxicity (repetitive exposure) : Class 1 (lung)
Environmental effects : None
Label elements Silicon carbide Pictorial indication or symbol : Health hazards
Term calling for attention : Danger Hazard information : May cause cancer Causes damage to organs Respiratory system or organs(lung) caused by long-term or repetitive exposure GHS classificationContinuous glass fiber
Physical and chemical hazards : None Human health hazard
Skin corrosivityIrritating property : Class 2 (Irritant) Serious damage to eyesIrritating property : Class 2B (mildly irritating to eyes) Specific target organ/systemic toxicity (single exposure) : Class 3respiratory tract irritation
Environmental effects : None
Label elements Continuous glass fiber
Pictorial indication or symbol : Exclamation mark Term calling for attention : Warning Hazard information : Irritating property to skin mildly irritating to eyes
Respiratory tract irritation May cause irritation to respiratory system
3. Composition/Information of Ingredients Substance/Mixture : Mixture
Calcium silicate board is a product obtained by press molding a mixture of reinforced fiber and calcium silicate crystal which is obtained by hydrothermally reacting calcareous material and siliceous material with water, and by then drying the molded product.
This product contains calcium silicate as a main ingredient and continuous glass fiber as inorganic reinforced fiber.
Name Content Reference No. of notice through official gazette CAS No.
Calcium silicate 80 to 90% 1-194 1344-95-2 Continuous glass fiber Less than 10% Not numbered 65997-17-3 Crystalline silica Less than 3% 1-548 14808-60-7 Iron oxide Less than 3% 1-357 1309-37-1 Silicon carbide Less than 5% 1-174 409-21-2
* The iron oxide given in the table is derived from the raw material.
The fiber used in this product is mainly continuous glass fiber, and does not include asbestos fiber.
This product does not fall under formaldehyde releasing building material, so it is out of notified material. Hence, this product does not contain substances regulated by the Building Code such as chlorpyrifos and formaldehyde because these substances are not used as raw materials or in the process.
-
DAIPALITE 03E-7
3/5
4. First Aid Measures Eye contact : Flush the affected eye with clean water until foreign body feeling disappears. Dont rub the eye. If any pain remains or something wrong with the eye, get medical treatment by an eye doctor. Skin contact : Wash the product adhering to skin away with water or lukewarm water, and wash the affected
area with soap and water thoroughly. If pain lasts or any symptom developsget medical treatment. Inhalation : Gargle with water or lukewarm water. Move to fresh air, and get medical treatment by a physician if needed. Ingestion : Gargle with water or lukewarm water. Get medical treatment by a physician if needed. 5. Fire Fighting Measures
Because this product is noncombustible, it is unnecessary to take fire fighting measure. 6. Accidental Release Measures
Because this product is solid body, it is unnecessary to take accidental release measure.
7. Handling and Storage [Precautions on handling]
Wear a dust protective mask as needed during handling. If the product makes contact with working cloth, remove it taking care not to scatter the dust. After handling, gargle and wash hands.
[Precautions on storage] Avoid exposure of the product to water, and store the product at a fixed place.
8. Exposure Controls/Personal Protection [Engineering measures]
Seal off the generation source of the dust, or install local exhaust ventilation or dust-proof devices. [Personal protection equipment]
Dust protective mask Wear a dust protective mask as needed during handling. Use either a replaceable dust protective mask or an air-supplied type dust protective respirator, that has been approved in national examination. In any case, pay special attention to the state of the mask adhering to a face. Perform proper maintenance such as inspection and replacement of the filter.
Gloves, working clothes, etc. Wear gloves and working cloth suitable for the work as needed, and skin shall not be exposed.
Protective glasses Use personal protective equipment suitable for the work, for example, goggles or protective glasses with side shields, if needed.
9. Physical/Chemical Properties Physical state : Board or Pipecover Color : White to gray Odor : Odorless Density(Bulk density) : About 0.1 to 0.15 g/cm3
10. Stability and Reactivity Stable. The product is partly dissolved in acid.
-
DAIPALITE 03E-7
4/5
11. Toxicological Information Crystalline silica
Carcinogenicity : This product is classified as 1A in this MSDS, because it is classified as 1 in IARC68(1997)2), as K in NTP 4), and as 1 in the recommendation by Japan Society of Occupational Health 3). IARC group 1 (carcinogenic to humans)
Specific target organ/systemic toxicity (single exposure) : There are little data on the single exposure compared with the repetitive exposure, but there
are some descriptions that even short-term exposure of humans to this product affects respiratory system if humans inhale high concentration of the product 2), 6), 7). This product is classified as Class1 (Respiratory system) because IARC 2) is Priority 1 document.
Specific target organ/systemic toxicity (repetitive exposure) : This product is ranked as Class 1 (Respiratory systemKidney), because Priority 1 document
describes that this product affects human respiratory system and kidney 1), 2), 5). Iron oxide
Skin corrosivity/Irritating property : This material causes redness on human skin and has medium irritating property. 8), 9) Serious damage/Irritating property to eyes : This material is corrosive to human eyes. 9)
Specific target organ/systemic toxicity (single exposure) : This material causes cough and difficulty in breathing
Specific target organ/systemic toxicity (repetitive exposure) : It is reported that this material causes human siderosis. 10)
Silicon carbide Carcinogenicity : This product is classified as 1B in this MSDS, because it is classified as A2 in ACGIH11). Specific target organ/systemic toxicity (single exposure) : This product is classified as Class1(Respiratory system) based on description11) that
pulmonary edema, pulmonary hemorrhage, pneumonitis, bronchiolar collapse, alveolar expansion imperfection were seen with rats within dosage of guidance in Class1.
Specific target organ/systemic toxicity (repetitive exposure) : This product is classified as Class1(Respiratory system) based on description11),12) that
pneumoconiosis, change of the chest radiograph photographic image, pulmonary fibrosis, a node, silicosis were seen with humans.
Continuous glass fiber Skin corrosivity/Irritating property : This material caused strong itch and irritation by mechanical stimulus with calling exposure.
This mechanical stimulus is temporary, and has relation with fiber more than 5m. In addition, the stimulant dermatitis accrues with calling exposure, too.
Serious damage/Irritating property to eyes : This material caused mechanical irritation with calling exposure. This mechanical stimulus is
temporary, and has relation with fiber more than 5mACGIH(2001)ATSDR(2004). Specific target organ/systemic toxicity (single exposure)
: This material causes temporary respiratory tract irritation with calling exposure, but the respiratory tract irritation disappears when exposure disappears.
12. Ecological information
There is no report which confirms influence to aquatic organisms.
13. Disposal Consideration When this product is disposed of as waste from business activity, it is regarded as industrial waste. Dispose of this product as glass waste and pottery waste by landfill in the least controlled landfill site according to the Waste Management and Public Cleaning Law.
14. Transport Information No precautions are required. However, take care not to give damage to the package because the dust scatters.
15. Regulatory Information Handle this product according to the Ordinance on Prevention of Hazards Due to Dust.
Crystalline silica, Iron oxide, Silicon carbide : Harmful substances of which names and other information are to be notified (Industrial Safety and Health
Law, Article 57-2, Enforcement Ordinance, Article 18-2, Appendix No. 9 (Government ordinance No. Silica : No. 312, Iron oxide : No. 192, Silicon carbide : No. 336)
-
DAIPALITE 03E-7
5/5
16. Other information [Reference] 1) CICAD24, 2000 2) IARC68, 1997 3) Recommendation by Japan Society of Occupational Health (2005) 4) NTP RoC (11th, 2005) 5) ACGIH-TLV (2005) 6) SITTIG (4th, 2002) 7) DHP (13th, 2002) 8) ICSC (2004)
9) IUCLID (2000) 10) ACGIH (2001) 11) ACGIH(2003) 12) HSDB(2005) 13) Monographs on Evaluation of the Carcinogenic Risks to Humans Vol.81(2002) Man-made
Vitreous Fibers 14) ATSDR(2004)
The information contained herein may be revised based on new knowledge. Among the descriptions of this MSDS, the information such as the content and the physical/chemical properties does not represent a guarantee. Evaluation of hazards is prepared based on our material and data of the product available at the date of publishing, but it is not considered to be exhaustive.
-
industrial and technical
General Product informationroxul stone wool products are made of basalt, a volcanic stone.
rocktech WM(Wired Mats) series
roxul stone wool products are non-combustible with a
melting point of approximately 1000c. they are particu-
larly suitable for thermal insulation, fire protection and
sound reduction/absorption.
roxul stone wool is inorganic and contains no nutritious
substance. therefore it will not be attacked by microor-
ganisms. Mineral wool will not rot and does not attract
vermin.
no cFcs, hFcs, hcFcs or asbestos are used in the manu-
facture of roxul stone wool products.
Product data sheet
-
industrial and technical
Common applications
rocktech WM is particularly suited to meet the specifica-
tion requirements of thermal insulation, fire protection
and sound attenuation of large process pipework, tanks,
vessels, boilers and ducts. rocktech WM is suitable
where high temperatures combined with vibrations or
high fire resistance is required. retention of the fibres by
the 25mm (1) wire mesh prevents any cracking or break-
ing. Wire mesh can be made from either galvanized steel
or stainless steel materials.
Packaging and storage
rocktech WM is shrink-wrapped in polyethylene sheets or
cling wrap for ease of handling, transportation, storage
and identification. Products should be stored indoors or
under a waterproof covering.
Basic installation guideline
rocktech WM can be cut to required length and wrapped
tightly around the equipment. the edges of each mattress
should be butt jointed closely together to eliminate gaps
and stitched using steel wire. rocktech WM can be se-
cured to the equipment with steel bands or pins with
speed clips.
RockTech WM (Wired Mats)
Product data sheet
www.rockwoolasia.comrtWM/04-2011/0/en
-
industrial and technical
Producttype
nominal density (kg/m3)
length thickness
WM450
WM650
WM650 hd
80
100
128
25
-
6.0
5.0
30
-
6.0
5.0
40
6.0
5.0
4.0
75
2.5
2.5
2.0
50
5.0
5.0
4.0
80
2.5
2.5
2.0
60
4.0
4.0
2.5
90
2.5
2.5
-
70
4.0
2.5
2.0
100
2.5
2.5
-
Dimensions and densities standard width: 1000mm
m
m
m
Producttype
nominal density (kg/m3)
length thickness
WM450
WM650
WM650 hd
80
100
128
25
-
8.0
8.0
30
-
8.0
8.0
40
6.0
6.0
6.0
75
4.0
4.0
3.0
50
5.0
5.0
4.0
80
3.0
3.0
3.0
60
4.0
4.0
3.0
90
3.0
3.0
-
70
4.0
4.0
3.0
100
3.0
3.0
-
standard width: 600mm
m
m
m
RockTech WM (Wired Mats)
Product data sheet
www.rockwoolasia.comrtWM/04-2011/0/en
-
www.rockwoolasia.comrtWM/04-2011/0/en
RockTech WM (Wired Mats)
Note: The information contained in this data sheet is believed to be correct at the date of publication . Rockwool Asia does not accept responsibility for the consequences of using RockTech WM in applications different from those described above.
Product types
Maximum service temperature (c)
Fire Performance
Water absorption
corrosion resistance
compliance to standards
WM450
450
less than 1kg/m2
rocktech WM conforms to astM c592 type i and ii, standard specification for Mineral Fiber Blanket insulation and Blanket-type Pipe insulation (Metal-Mesh covered) (industrial type). rocktech WM complies with the requirements of Bs 3958 : Part 3 Metal mesh faced mats and mattresses and can be used to sat-isfy Bs 5422 thermal insulating materials on pipes, ductwork and equipment.
standards
astM c411
Bs 476 Part 4
en 1609
WM650
650
non-combustible
roxul stone wool does not attack or damage other materials with which it comes into contact, neither does it further the corrosion of metal. no aggres-sive gasses are released when influenced by fire. rocktech WM meets the requirements for use over stainless steel in accordance with astM c 795.
Technical Parameters
industrial and technical
Mean Temperatures
C
24
38
93
149
204
260
316
371
Thermal conductivity (W/mK)
rocktech s450
0.036
0.039
0.049
0.062
0.079
0.101
rocktech s650
0.036
0.039
0.049
0.060
0.076
0.092
0.108
0.124
Thermal conductivity
Note: Thermal conductivity of RockTech WM meets the ASTM C592: Standard Specification For Mineral Fiber Blanket Insulation and Blanket - Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type). For actual results, please refer to your local representatives.
Product data sheet
Rockwool Insulation (M) Sdn Bhdlot 4, solok Waja 1, Bukit raja industrial estate,41050 Klang, selangor, Malaysiatel: [+60] 3 3341 3444Fax: [+60] 3 3341 5779
Rockwool Building Materials (Singapore) Pte Ltdno. 8, tuas avenue 2, Jurong townsingapore 639448tel: [+65] 6861 4722Fax: [+65] 6862 3533
Rockwool Firesafe Insulation (Guangzhou) Co. Ltd.3 taihua st, Yonghe dist of Guangzhou econ & tech development dist, Guangzhou, Guangdong Province, P. r. china (511356)tel: [+86] 20 8298 6668Fax: [+86] 20 8298 6877
Rockwool (Thailand) Limitedhemaraj eastern industrial estate (Map ta Phut)1 soi G 2, Pakornsongkrohraj road, huaypong, Muang, rayong 21150, thailandtel: [+66] 3868 5110Fax: [+66] 3868 4938
Rockwool Malaysia Sdn Bhd175 a&B, Kawasan Perindustrian air Keroh, Jalan lingkungan usaha, 75450 MelakaMalaysiatel: [+60] 6 233 2010Fax: [+60] 6 233 2012
-
35-00/45-00 Product Data Sheet
Sam Hwa Chemicals Co., Ltd. Specialty Construction Brands, Inc.
SAM HWA Chemicals. Co., Ltd. is appointed as an exclusively technical licensee of Specialty Construction Brands, Inc.
The warranty of product quality can be done for six months from the date of purchase. E-Mail: [email protected]
PROPERTIES
TROWEL/GLOVE COLOR BRUSH/SPRAY
35-00 White 45-00
35-01 Aluminum Gray 45-01
Other colors available on special order.
AVERAGE WEIGHT/U.S. GALLON: 11.2 lbs (1.34 kg/)
AVERAGE NON-VOLATILE (FSTM 9A):
63 ~ 65% by volume (73 ~ 75% by weight)
COVERAGE RANGE:
(Subject to the type of material being coated).
Wet coverages shown below are for smooth non-porous surfaces.
Porous or rough surfaces may require higher gallonage to attain
required dry thickness.
Dry Thickness: 0.062 inch (1.6 mm)
Equivalent Wet Coverage: 0.096 inch (2.4 mm)
6 gal/100 sq. ft. (2.4 L/m2).
DRYING TIME 73 (23 ) 50% RH (ASTM D 1640): Set to touch: 3 hours
Dry through: 16 hours
SERVICE TEMPERATURE LIMITS (FSTM 70):
(Temperature at coated surface)
- 20 ~ 200 ( -29 ~ 93 )
WATER VAPOR PERMEANCE (ASTM F 1249):
3.0 perms (2.0 metric perms) at 1/16 inch (1.6 mm) dry film
thickness; decreasing on aging to 1.0 perms (0.7 metric perm)
WET FLAMMABILITY (ASTM D 3278):
No flash to boiling, 205 (96)
SURFACE BURNING CHARACTERISTICS
(ASTM E 84):
Flame Spread: 20 Smoke Developed: 25 ~ 50
Tested at coverage rate of 16.7 sq. ft. per gallon
(6 gal/100 sq. ft., 2.4 m2/)
Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board.
The flame spread may vary at different product thickness and/or
when applied over other surfaces.
FOSTER SEALFAS G-P-M MASTIC
FOSTER SEALFAS G-P-M MASTIC is a high solids waterbase
general purpose mastic having excellent trowel and spray
properties.
G-P-M is used for the protection of thermal insulation and hard,
dry cement coats, both indoors and outdoors.
SEALFAS G-P-M MASTIC is fire-resistive and features ease of
application, non-flammability, non-toxicity, mild odor, range of
colors, insulation compatibility, good package stability, plus
excellent outdoor durability.
SEALFAS G-P-M MASTIC meets NFPA 90A and 90B 25/50
requirements.
SEALFAS G-P-M MASTIC 35-00 and 45-00 conform with current
requirements regarding use in meat and poultry processing areas
under federal inspection. Letter of certification is available upon
request.
SEALFAS G-P-M MASTIC 35-00Q and 45-00Q can be supplied
to meet the stress corrosion and chemical analysis requirements
of MIL-I-24244C or nuclear regulatory guide 1.36 on special order.
SEALFAS G-P-M MASTIC contains no asbestos, lead,
mercury, or mercury compounds.
REMARKS
Store and apply between 40 (4 ) and 100 (38 ). Protect from freezing until dry.
To resist rain washoff, allow at least 16 hours drying time above
40F (4C), with a relative humidity of 50%. Higher humidity at
lower temperatures may retard drying.
Always test paper facings for acceptable adhesion before using.
Select WEATHERITE Mastics for use over foil facings.
Outdoor horizontal surfaces must always drain completely. A pitch
of at least 1/2 per foot (4cm/m) is recommended.
Always select 35-00 or 45-00 white for use over polystyrene
insulation installed outdoors.
-
802297PM Page 1 of 507-06-2011
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
REVISION DATE: 06-15-2011 SUPERSEDES: 08-25-2009
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION COMPANY INFORMATION H.B. Fuller Construction Products Inc. 1105 S. Frontenac Street Aurora, IL 60504 Phone: 1-800-552-6225
Medical Emergency Phone Number (24 Hours): 1-888-853-1758 Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION PRODUCT NUMBER: FOSTER 35-00 PRODUCT DESCRIPTION: Mastic PRODUCT IDENTIFIER: 802297PM
SECTION 2: HAZARDS IDENTIFICATION EMERGENCY OVERVIEW PHYSICAL STATE: Liquid COLOR: White ODOR: Mild Sweet Cancer hazard.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRYEYE: Can cause minor irritation, tearing and reddening. SKIN: Can cause minor skin irritation, defatting, and dermatitis. INHALATION: Can cause minor respiratory irritation. Inhalation of dusts produced during cutting, grinding or sanding of this product may cause irritation of the respiratory tract. Overexposure to crystalline silica may cause silicosis. This product contains one or more materials that may be hazardous when present as an airborne dust. During normal handling of the product, the material is encapsulated within the product and will not present an exposure risk. Once the product has reached its final state and is abraded or disturbed, dusting and exposure may occur.INGESTION: Ingestion is not an anticipated route of exposure. No hazard in normal industrial use. LONG-TERM (CHRONIC) HEALTH EFFECTS TARGET ORGAN(S): Lungs
REGULATED CARCINOGEN STATUS: Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed carcinogens. Titanium dioxide Crystalline silica Vinyl acetate
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Lung disease
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS # PERCENT Aluminum hydroxide 21645-51-2 10 - 30
Calcium carbonate 471-34-1 10 - 30
-
802297PM Page 2 of 507-06-2011
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Titanium dioxide 13463-67-7 1 - 5
Crystalline silica 14808-60-7 0.1 - 1
Vinyl acetate 108-05-4 0.1 - 1
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous Materials Information System ingredient disclosure list. See Section 8 for exposure limit guidelines.
SECTION 4: FIRST AID MEASURES IF IN EYES: Use an eye wash to remove a chemical from your eye regardless of the level of hazard. Flush the affected eye for at least twenty minutes. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Seek medical advice after flushing. IF ON SKIN: Wash with soap and water. Get medical attention if irritation develops or persists. IF VAPORS INHALED: Remove to fresh air. Call a physician if symptoms persist. IF SWALLOWED: Do not induce vomiting. Seek medical attention if symptoms develop. Provide medical care provider with this MSDS. Induced vomiting may lead to aspiration of the material into the lungs potentially causing chemical pneumonitis that may be fatal.
SECTION 5: FIRE FIGHTING MEASURES FLASH POINT: Non flammable AUTOIGNITION TEMPERATURE: Not establishedLOWER EXPLOSIVE LIMIT (% in air): Not established UPPER EXPLOSIVE LIMIT (% in air): Not established EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide. UNUSUAL FIRE AND EXPLOSION HAZARDS: There is a possibility of pressure buildup in closed containers
when heated. Water spray may be used to cool the containers. SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-
contained breathing apparatus and full protective equipment. HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES SPECIAL PROTECTION: No adverse health effects expected from the clean-up of spilled material.
Follow personal protective equipment recommendations found in Section 8 of this MSDS.
CLEAN-UP: Dike if necessary, contain spill with inert absorbent and transfer to containers for disposal. Keep spilled product out of sewers, watersheds, or water systems.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE Handling: No special handling instructions due to toxicity.
Storage: Store in a cool, dry place. Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION EYE PROTECTION: Wear safety glasses when handling this product. SKIN PROTECTION: Avoid skin contact by wearing chemically resistant gloves. GLOVES: Not normally required. Use nitrile gloves if conditions warrant.
-
802297PM Page 3 of 507-06-2011
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
RESPIRATORY PROTECTION: Respiratory protection may be required to avoid overexposure when handling this product. Use a respirator if general room ventilation is not available or sufficient to eliminate symptoms. Respirators should be selected by and used following requirements found in OSHA's respirator standard (29 CFR 1910.134).
VENTILATION: Use local exhaust ventilation or other engineering controls to minimize exposures.
EXPOSURE LIMITS:Chemical Name ACGIH EXPOSURE LIMITS OSHA PEL Aluminum hydroxide Not established Not established
Calcium carbonate Not established 15 mg/m3 TWA (total dust); 5 mg/m3 TWA (respirable fraction)
Titanium dioxide 10 mg/m3 TWA 15 mg/m3 TWA (total dust)
Crystalline silica 0.025 mg/m3 TWA (respirable fraction) ((250)/(%SiO2 + 5) mppcf TWA (respirable)); ((10)/(%SiO2 + 2) mg/m3 TWA (respirable)); ((30)/(%SiO2 + 2) mg/m3 TWA (total dust))
Vinyl acetate 10 ppm TWA 15 ppm STEL
Not established
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE: Liquid COLOR: White ODOR: Mild Sweet ODOR THRESHOLD: Not established WEIGHT PER GALLON (lbs.): 11.6 SPECIFIC GRAVITY: 1.39 SOLIDS (% by weight): 71.3
pH: Not established FLASH POINT: Non flammable BOILING POINT (deg. C): Not established FREEZING/MELTING POINT (deg. C): Not established VAPOR PRESSURE (mm Hg): Not established VAPOR DENSITY: Not established EVAPORATION RATE: Not established OCTANOL/WATER COEFFICIENT: Not established VOC, weight percent 1.7 VOC, EPA Method 24, less water and exempt solvents
(theoretically determined) 37g/liter of material
SECTION 10: STABILITY AND REACTIVITY STABILITY: Stable under normal conditions. CHEMICAL INCOMPATIBILITY: Not established HAZARDOUS POLYMERIZATION: Will not occur. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide
SECTION 11: TOXICOLOGICAL INFORMATION COMPONENT LD50/LC50
-
802297PM Page 4 of 507-06-2011
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Aluminum hydroxide Not established
Calcium carbonate Oral LD50 Rat = 6450 mg/kg
Titanium dioxide Not established
Crystalline silica Not established
Vinyl acetate Oral LD50 Rat = 2920 mg/kg Inhalation LC50 Rat = 11400 ml/cu m Dermal LD50 Rabbit = 2335 mg/kg
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION OVERVIEW: No ecological information available
SECTION 13: DISPOSAL CONSIDERATIONS To the best of our knowledge, this product does not meet the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR 261. Solidify and dispose of in an approved landfill. Consult state, local or provincial authorities for more restrictive requirements.
SECTION 14: TRANSPORTATION INFORMATION Consult Bill of Lading for transportation information. DOT: NOT REGULATED IATA: NOT REGULATED
SECTION 15: REGULATORY INFORMATION INVENTORY STATUS U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements. CANADIAN CEPA DSL: The components of this product are included on the DSL or are exempt from
DSL requirements. EUROPEAN EINECS: As a result of the introduction of REACH into Europe, this product cannot be
imported into Europe unless the REACH requirements are met. AUSTRALIA AICS: This product is in compliance with the Australian Inventory of Chemical
Substances requirements. KOREAN TCCL: This product is in compliance with the Korean Existing Chemicals List
requirements. If you need more information about the inventory status of this product call 651-236-5858.
This product may contain chemical substances that are regulated for export by various government agencies (such as the Environmental Protection Agency, the Bureau of Industry and Security, or the Drug Enforcement Administration, among others). Before exporting this product from the USA or Canada, we recommend you contact us at 651-236-5858 (USA) or 450-655-1306 x227 (Canada) to request an export review.
FEDERAL REPORTING EPA SARA Title III Section 313 Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372. EPA has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations. Chemical Name CAS# % Vinyl acetate 108-05-4 0.1 - 1
-
802297PM Page 5 of 507-06-2011
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous Materials Information System. D2A
STATE REPORTING This MSDS is not prepared for distribution in California.
SECTION 16: ADDITIONAL INFORMATION This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace Hazardous Materials Information System (WHMIS).
HMIS RATING: HEALTH -- 0 FLAMMABILITY -- 0 REACTIVITY -- 0 See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment recommendations.
Prepared by: The Global Regulatory Department Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the information is derived from information provided to H.B.Fuller Construction Products, Inc. from its suppliers, and because H.B.Fuller Construction Products, Inc. has no control over the conditions of handling and use, H.B.Fuller Construction Products, Inc. makes no warranty, expressed or implied, regarding the accuracy of the data or the results to be obtained from the use thereof. The information is supplied solely for your information and consideration, and H.B.Fuller Construction Products, Inc. assumes no responsibility for use or reliance thereon. It is the responsibility of the user of H.B.Fuller Construction Products, Inc. products to comply with all applicable federal, state and local laws and regulations.
-
81-27 Product Data Sheet
Sam Hwa Chemicals Co., Ltd. Specialty Construction Brands, Inc.
SAM HWA Chemicals. Co., Ltd. is appointed as an exclusively technical licensee of Specialty Construction Brands, Inc.
The warranty of product quality can be done for six months from the date of purchase. E-Mail: [email protected]
PROPERTIES
COLOR:
Beige
APPLICATION CONSISTENCY:
Brush, Trowel
AVERAGE WEIGHT/U.S. GALLON (ASTM D 1475):
13.7 lbs. (1.64 kg/l)
AVERAGE NON-VOLATILE (ASTM D 2369):
41% by volume (63% by weight)
COVERAGE RANGE (FSTM 72):
(Subject to type of surface and nature of material being
coated)
Brush: 40 to 50 sq. ft. per gal. (1.0 to 1.2 m2/l)
0.040 in. to 0.032 in. (1.0 to .8 mm) wet film
thickness.
Trowel: 25 to 30 sq. ft. per gal. (0.6 to 0.7 m2/l)
0.064 in. to 0.053 in. (1.6 to 1.3 mm) wet film thickness.
BONDING TIME RANGE (FSTM 66):
0 to 5 minutes
SERVICE TEMPERATURE LIMITS (FSTM 70):
(Temperature at coated surface)
50F to 800F (10C to 427C)
WET FLAMMABILITY (ASTM D 93):
No flash to boiling 212F (100C)
DRY COMBUSTIBILITY (FSTM 44):
Incombustible
FOSTER FIBROUS ADHESIVE
Foster Fibrous Adhesive is a sodium silicate based
Incombustible adhesive for bonding calcium silicate and
expanded perlite thermal insulation to itself and to
nonporous surfaces. It offers maximum adhesion and
optimum working qualities and it forms a hard, brittle,
incombustible film.
Fibrous Adhesive can also be used for lagging high
temperature alkali resistant cloth on high temperature
insulation.
Nuclear Grade Fibrous Adhesive 81-27Q can be supplied
to meet the stress corrosion and chemical analysis
requirements of MIL-I-24244C or Nuclear Regulatory Guide
1.36 on special order.
Fibrous Adhesive contains no asbestos, lead, mercury, or
mercury compounds.
Fibrous Adhesive meets requirements for LEED IEQ 4.1
Low-Emitting Materials, Adhesives and Sealants. VOC: 0
g/l, less water and exempt solvents.
REMARKS
Store and apply between 40F (4C) and 100F (38C),
protect from freezing until dry.
Since the dry adhesive film is soluble in water, it should not
be used where moisture will be encountered.
Because of its sodium silicate base, this product is not
recommended for use with glass fiber or other alkali
sensitive insulations.
Primed or painted metal surfaces should be tested for
compatibility.
If used between impermeable surfaces, drying time will be
Extended
-
Page 1 of 506-12-2012802388PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
REVISION DATE: 05-16-2012 SUPERSEDES: 10-05-2009
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION COMPANY INFORMATION H.B. Fuller Construction Products Inc. 1105 S. Frontenac Street Aurora, IL 60504 Phone: 1-800-552-6225
Medical Emergency Phone Number (24 Hours): 1-888-853-1758 Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION PRODUCT NUMBER: FOSTER 81-27 PRODUCT NAME: FOSTER 81-27 PRODUCT DESCRIPTION: Adhesive PRODUCT IDENTIFIER: 802388PM
SECTION 2: HAZARDS IDENTIFICATION EMERGENCY OVERVIEW PHYSICAL STATE: Liquid COLOR: Beige ODOR: Earthy Corrosive to eye tissue. Causes severe skin irritation. Severe respiratory tract irritant. Harmful if swallowed.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRYEYE: Corrosive to eye tissue. Can cause severe irritation, tearing, and burns that can quickly lead to permanent injury including blindness. SKIN: Contact causes severe skin irritation and possible burns. INHALATION: Can cause severe respiratory irritation, nausea, and headache. Inhalation of dusts produced during cutting, grinding or sanding of this product may cause irritation of the respiratory tract. This product contains one or more materials that may be hazardous when present as an airborne dust. During normal handling of the product, the material is encapsulated within the product and will not present an exposure risk. Once the product has reached its final state and is abraded or disturbed, dusting and exposure may occur.INGESTION: Ingestion is not an anticipated route of exposure. Harmful if swallowed. Corrosive to tissue. Can cause severe and permanent damage to mouth, throat, stomach. Aspiration may lead to lung damage. LONG-TERM (CHRONIC) HEALTH EFFECTS TARGET ORGAN(S): Lungs
REGULATED CARCINOGEN STATUS: Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed carcinogens.
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Lung disease
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS # PERCENT Sodium silicate 1344-09-8 30 - 50
-
Page 2 of 506-12-2012802388PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Kaolin clay 1332-58-7 10 - 30
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous Materials Information System ingredient disclosure list. See Section 8 for exposure limit guidelines.
SECTION 4: FIRST AID MEASURES IF IN EYES: Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids often. This corrosive material can cause immediate and permanent eye damage. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention and monitor the eye daily as advised by your physician. IF ON SKIN: Wash with soap and water. Remove contaminated clothing, launder immediately, and discard contaminated leather goods. Get medical attention immediately. IF VAPORS INHALED: Remove to fresh air. Restore breathing, if necessary. Keep warm and quiet. Call a physician. IF SWALLOWED: Corrosive. Do not induce vomiting! Drink one glass of water followed by milk if available. Seek medical attention immediately. Do not give anything by mouth to an unconscious person. Induced vomiting may lead to aspiration of the material into the lungs potentially causing chemical pneumonitis that may be fatal.
SECTION 5: FIRE FIGHTING MEASURES FLASH POINT: Non flammable AUTOIGNITION TEMPERATURE: Not establishedLOWER EXPLOSIVE LIMIT (% in air): Not established UPPER EXPLOSIVE LIMIT (% in air): Not established EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide. UNUSUAL FIRE AND EXPLOSION HAZARDS: There is a possibility of pressure buildup in closed containers
when heated. Water spray may be used to cool the containers. SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-
contained breathing apparatus and full protective equipment. HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES SPECIAL PROTECTION: Exposure to the spilled material may be severely irritating or toxic. Follow
personal protective equipment recommendations found in Section 8 of this MSDS. Personal protective equipment needs must be evaluated based on information provided on this sheet and the special circumstances created by the spill including; the material spilled, the quantity of the spill, and the area in which the spill occurred. Never exceed any occupational exposure limits.
CLEAN-UP: Dike if necessary, contain spill with inert absorbent and transfer to containers for disposal. Keep spilled product out of sewers, watersheds, or water systems. Contain spill, dilute if necessary and neutralize. Remove with inert absorbent.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE Handling: Toxic or severely irritating material. Avoid contacting and avoid breathing the material. Use
only in a well ventilated area. Aluminum is not an acceptable material of construction for pumps, mixers, fittings or storage for this product.
-
Page 3 of 506-12-2012802388PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Storage: Store in a cool, dry place. Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION EYE PROTECTION: Wear chemical splash goggles when handling this product.
Additionally, wear a face shield when the possibility of splashing of liquid exists. Do not wear contact lenses. Have an eye wash station available.
SKIN PROTECTION: Prevent contact with this product. Wear chemically resistant gloves, long sleeved shirt, an apron, and other protective equipment depending on conditions of use.
GLOVES: Butyl rubber RESPIRATORY PROTECTION: Respiratory protection will be required when ventilation or other
engineering controls can not reduce the exposure to acceptable levels. NIOSH approved air purifying respirator with dust/mist filter if product is sprayed. Respirators should be selected by and used following requirements found in OSHA's respirator standard (29 CFR 1910.134).
VENTILATION: Local exhaust ventilation or other engineering controls are normally required when handling or using this product to avoid overexposure.
EXPOSURE LIMITS:Chemical Name ACGIH EXPOSURE LIMITS OSHA PEL Sodium silicate Not established Not established
Kaolin clay 2 mg/m3 TWA (particulate matter containing no asbestos and
-
Page 4 of 506-12-2012802388PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
SECTION 10: STABILITY AND REACTIVITY STABILITY: Stable under normal conditions. CHEMICAL INCOMPATIBILITY: Aluminum alloys HAZARDOUS POLYMERIZATION: Will not occur. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide
SECTION 11: TOXICOLOGICAL INFORMATION COMPONENT LD50/LC50 Sodium silicate Oral LD50 Rat = 1 g/kg
Kaolin clay Not established
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION OVERVIEW: No ecological information available
SECTION 13: DISPOSAL CONSIDERATIONS This product meets the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR 261. It is corrosive waste class D002. We recommend the required corrosivity testing on product to determine the appropriate waste category. Disposal via incineration is recommended. Consult your state, local, or provincial authorities for more restrictive requirements. SECTION 14: TRANSPORTATION INFORMATION Consult Bill of Lading for transportation information. DOT: NOT REGULATED IATA: NOT REGULATED
SECTION 15: REGULATORY INFORMATION INVENTORY STATUS U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements. CANADIAN CEPA DSL: The components of this product are included on the DSL or are exempt from
DSL requirements. EUROPEAN EINECS: As a result of the introduction of REACH into Europe, this product cannot be
imported into Europe unless the REACH requirements are met. AUSTRALIA AICS: This product is in compliance with the Australian Inventory of Chemical
Substances requirements. JAPAN ENCS: This product is in compliance with the Japanese Existing and New Chemical
Substances requirements. KOREAN TCCL: This product is in compliance with the Korean Existing Chemicals List
requirements. PHILIPPINES: This product is in compliance with the Philippine Inventory of Chemicals and
Chemical Substances requirements. If you need more information about the inventory status of this product call 651-236-5858.
This product may contain chemical substances that are regulated for export by various government agencies (such as the Environmental Protection Agency, the Bureau of Industry and Security, or the Drug Enforcement Administration, among others). Before exporting this product from the USA or Canada, we recommend you contact us at 651-236-5858 (USA) or 450-655-1306 x227 (Canada) to request an export review.
FEDERAL REPORTING EPA SARA Title III Section 313
-
Page 5 of 506-12-2012802388PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372. EPA has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations. Chemical Name CAS# %
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous Materials Information System. D2B E
STATE REPORTING Proposition 65, The Safe Drinking Water and Toxic Enforcement Act of 1986: Unless listed below, this product does not contain known levels of any chemical known to the State of California to cause cancer or reproductive harm. Chemical Name/List CAS Percent Quartz (Carcinogen) 14808-60-7 0.01 - 0.1 Nickel (metallic) (Carcinogen) 7440-02-0 < 10 ppm Lead (Carcinogen) 7439-92-1 < 10 ppm Lead (Developmental toxin) 7439-92-1 < 10 ppm Lead (Female reproductive toxin) 7439-92-1 < 10 ppm Lead (Male reproductive toxin) 7439-92-1 < 10 ppm
SECTION 16: ADDITIONAL INFORMATION This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace Hazardous Materials Information System (WHMIS).
HMIS RATING: HEALTH -- 3 FLAMMABILITY -- 0 REACTIVITY -- 0 See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment recommendations.
Prepared by: The Global Regulatory Department Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the information is derived from information provided to H.B.Fuller Construction Products, Inc. from its suppliers, and because H.B.Fuller Construction Products, Inc. has no control over the conditions of handling and use, H.B.Fuller Construction Products, Inc. makes no warranty, expressed or implied, regarding the accuracy of the data or the results to be obtained from the use thereof. The information is supplied solely for your information and consideration, and H.B.Fuller Construction Products, Inc. assumes no responsibility for use or reliance thereon. It is the responsibility of the user of H.B.Fuller Construction Products, Inc. products to comply with all applicable federal, state and local laws and regulations.
-
Glass Cloth No.10 1SPEVDU%BUB4IFFU
Sam Hwa Chemicals Co., Ltd. Specialty Construction Brands, Inc.
SAM HWA Chemicals. Co., Ltd. is appointed as an exclusively technical licensee of Specialty Construction Brands, Inc.
The warranty of product quality can be done for six months from the date of purchase. E-Mail: [email protected]
PROPERTIES
COLOR:
White
COMPOSITION:
Glass Cloth with Acryl resin coating
WEAVE:
Leno Plain
YARN:
Warp YARN: 33TEX Weft YARN: 67TEX
MESH:
Warp: 10 1 count/in.
Weft l: 10 1 count/in.
FABRIC THICKNESS:
0.13 0.02 mm
AVERAGE WEIGHT:
60 5 g/m2
WIDTH:
1,0005 mm
ROLL LENGTH:
200 0.1 meter
Glass Cloth No.10
Glass Cloth is made as per its different usage by assembling
several hundreds of the fine 5 ~ 13 thick inorganic fiber which
can be produced by forming a selected glass material melted by
temperature 1600~ 1800. It is being widely used in many industrial fields including leisure
industry in combination with various organic.
As fabric binded on minute thread, its interval is big and the
density is low. The penetration of resin is easy. It is mainly used
for reinforcement materials.
Glass Cloth can be used in such a condition as it is weaved and
also can be used after later- processing such as heat cleaning,
silane finish, prepreg, coloring, laminating and etc.
Glass Cloth gives reinforcement by being embedded between a
mastic tack coat and finish coat.
Glass Cloth for heat insulation made of the bulky processed ultra
finest fiber has more excellent heat resistant property and
flexibility, compared with the existing cloth. The asbestos which is
popular in last time, for fear of its cancer inductiveness, is
substituted with heat-resistant, incombustible glass cloth for the
purpose of heat insulation in a ship-building yard or in a factory.
-
95-44Product Data Sheet
PROPERTIES
COLOR: Aluminum APPLICATION CONSISTENCY: Trowel, Caulking Gun or Power Extrusion Equipment AVERAGE WEIGHT/U.S. GALLON (ASTM D 1475): 9.3 lbs. (1.1 kg/l) AVERAGE NON-VOLATILE (ASTM C 461): 52 to 58% by volume (65% by weight) COVERAGE RANGE (FSTM 72): Trowel: 12 to 25 sq. ft./gal. (0.29 to 0.61 m2/l) 1/8 to 1/16 in. (3.2 to 1.6 mm) wet film thickness. Caulking Gun: 125 lineal ft. per 10.5 fluid oz. tube, 1/8 in. bead. (38 m per .31 l tube, 3.2 mm bead) 30 lineal ft. per 10.5 fluid oz. tube, 1/4 in. bead (9 m per .31 l tube, 6.4 mm bead). DRYING TIME (ASTM D 15): Touch: 1/2 hour Through: 72 hours SERVICE TEMPERATURE LIMITS (FSTM 70): (Temperature at coated surface) Joint Sealant - Urethane Foam Minus 150F to 200F (-101C to 93C) Joint Sealant - Cellular Glass Minus 100F to 250F (-73C to 121C) Flashing Compound (Temperature at Flashed Surface) Minus 40F to 250F (-40C to 121C) WET FLAMMABILITY (ASTM D 3278) Flash Point: 105F (41C) SURFACE BURNING CHARACTERISTICS (ASTM E 84) Flame Spread: 15 Smoke Developed: 0 Tested at coverage rate of 25 sq. ft./gal. (0.61 m2/l) in 2 in. (5 cm) strip. Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board. The flame spread may vary at different product thicknesses and/or when applied over other surfaces. and Trademarks of Specialty Construction Brands, Inc. Visit us on the web at www.fosterproducts.com
FOSTER ELASTOLAR SEALANT FOSTER ELASTOLAR Sealant is a fire resistive, flexible butyl elastomer based vapor barrier sealant. It is designed for sealing joints in insulation (except polystyrene foam), metal, and masonry wherever maintenance of a water-tight and air-tight seal is required. It can be used as a joint sealant in low velocity duct air-conditioning systems. It is ideal for sealing the laps of aluminum jacketing to prevent the entrance of moisture. ELASTOLAR Sealant is a fast drying vapor barrier sealant that can be top coated with most solvent-thinned, flexible, light colored coatings without danger of bleed through. It is weather resistant and may be used outdoors without top coating. ELASTOLAR Sealant is the preferred product for flashing projections and terminations where a complete moisture and vapor seal is required. ELASTOLAR Sealant meets NFPA 90A and 90B 25/50 requirements. WATER VAPOR PERMEANCE: ASTM F-1249: 0.014 perm (0.0092 metric perm) at 0.094 in. (2.38 mm) dry film thickness. Tested at 100oF (38oC) and 90% RH The water vapor transmission through 1 in. of impermeable insulation in 12 x 18 in. blocks with 1/8 in. joints of ELASTOLAR Sealant is too small to measure. ELASTOLAR Sealant contains no asbestos, lead, mercury, or mercury compounds. ELASTOLAR Sealant may meet requirements for LEED IEQ 4.1 Low-Emitting Materials, Adhesives and Sealants for some applications where the use falls under the Other category. Refer to LEED guides for more information. VOC: 384 g/l, less water (336 g/l, less water cartridge grade) LIMITATIONS Store and apply between 40F and 100F (4C and 38C). Always test plastic materials for compatibility when using a solvent base product. When used in exposed locations without top-coating, this product may darken or discolor due to surface dirt pick-up. This will not affect its performance. Make certain this product is completely dry and the area is free from solvent odor if food is involved. Select Foster 30-45 for joint sealing polystyrene foam insulations.
1209
Specialty Construction Brands, Inc.
1105 South Frontenac Street Aurora, IL 60504 800-231-9541 fax 800-942-6856
-
APPLICATION GUIDE FOR
FOSTER ELASTOLAR SEALANT 95-44
MATERIAL PREPARATION DO NOT THIN. Apply only to clean, dry, oil free surfaces. Keep container closed when not in use. APPLICATION Apply by trowel, putty knife, caulking gun or power extrusion. When sealing insulation joints apply ELASTOLAR Sealant to the edges of abutting sections at 1/16 in. to 1/8 in. (1.6 mm to 3.2 mm) wet film thickness and press mating surfaces together firmly to squeeze out air bubbles and to obtain complete contact. Strike off excess sealant on surface with a trowel. When flashing, do not trowel out to feather edge, but maintain a minimum of 1/8 in. (3.2 mm) wet film thickness throughout entire area of use. Use membrane as specified. For best application, the material temperature should be 60F (16C) or higher. Note: Pressurized piping made from copper and aluminum alloys may be susceptible to under insulation corrosion when moisture is present and in direct contact with many materials. When used as a joint sealant direct contact between pressurized pipes made from these metals and the sealant should be prevented. POWER EXTRUSION ELASTOLAR Sealant may be applied using a wide variety of power (pressure) extrusion equipment suitable for use with solvent base sealants. Typical viscosity range: 1.5 -2.0 million cps. CLEAN-UP Use solvent such as chlorinated solvent (non-flammable) or mineral spirits (flammable) for cleaning tools and equipment.
DATA REPORTED FROM ASTM E84 FIRE TEST (TUNNEL TEST)
ADHESIVES H.B. Fuller Company
Surface Burning Characteristics 1/4 inch (6.4 mm) Inorganic
Reinforced Cement BoardSurface Flame Spread 15 Smoke Developed 0 Number of Coats 1 Tested as applied in a 2 in. wide strip at a coverage of 25 sq. ft. per gal.
CUSTOMER SERVICE: 800-231-9541
IMPORTANT: Specialty Construction Brands, Inc. warrants that each of its products will be manufactured in accordance with the specifications in effect on the date of manufacture. WE MAKE NO OTHER WARRANTIES AND EXPRESSLY DISCLAIM ANY WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE. If a product fails to meet this limited warranty, purchasers sole and exclusive remedy is replacement of the product or, at our option, refund of the purchase price. OUR ACCEPTANCE OF ANY ORDERS FOR THE PRODUCT IS EXPRESSLY CONDITIONAL UPON PURCHASERS ASSENT TO THE TERMS ON THE APPLICABLE INVOICE. ADEQUATE TESTS: The information contained herein we believe is correct to the best of our knowledge and tests. The recommendations and suggestions herein are made without guarantee or representation as to results. We recommend that adequate tests be performed by you to determine if this product meets all of your requirements. The warranted shelf life of our products is six months from date of shipment to the original purchaser.
For professional use only. Keep out of reach of children.
Consult Material Safety Data Sheet and container label for further information.
DS F95-44 R1209
-
Page 1 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
REVISION DATE: 10-03-2011 SUPERSEDES: 09-22-2009
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
COMPANY INFORMATION H.B. Fuller Construction Products Inc. 1105 S. Frontenac Street Aurora, IL 60504 Phone: 1-800-552-6225
Medical Emergency Phone Number (24 Hours): 1-888-853-1758 Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION PRODUCT NUMBER: FOSTER 95-44 PRODUCT NAME: FOSTER 95-44 PRODUCT DESCRIPTION: Sealant PRODUCT IDENTIFIER: 802435PM
SECTION 2: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW PHYSICAL STATE: Solid COLOR: Aluminum ODOR: Solvent Combustible Moderate eye irritant. Can cause skin irritation. Moderate respiratory tract irritant. Harmful if swallowed. Cancer hazard.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRYEYE: Can cause moderate irritation, tearing and reddening, but not likely to permanently injure eye tissue.
SKIN: Can cause skin irritation. Component(s) may be absorbed through intact skin, but it is unlikely that harmful effects will occur unless contact is prolonged, repeated, and extensive.
INHALATION: Can cause moderate respiratory irritation. Inhalation of dusts produced during cutting, grinding or sanding of this product may cause irritation of the respiratory tract. Inhalation of high concentrations may result in central nervous system (CNS) effects such as dizziness, weakness, fatigue, nausea, headache, and lack of coordination. Overexposure to crystalline silica may cause silicosis.
This product contains one or more materials that may be hazardous when present as an airborne dust. During normal handling of the product, the material is encapsulated within the product and will not present an exposure risk. Once the product has reached its final state and is abraded or disturbed, dusting and exposure may occur.
INGESTION: Ingestion is not an anticipated route of exposure. Harmful if swallowed. Irritating to mouth, throat, and stomach.
LONG-TERM (CHRONIC) HEALTH EFFECTS REPRODUCTIVE: Contains a substance that is a probable reproductive hazard based on human
studies. TARGET ORGAN(S): Kidneys Central nervous system Blood Lungs Liver
REGULATED CARCINOGEN STATUS:
-
Page 2 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed carcinogens. Crystalline silica
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Kidney disease; Blood disorders (like anemia); Lung disease; Liver disease
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS # PERCENT
Stoddard solvent 8052-41-3 10 - 30
Aromatic petroleum distillate 64742-95-6 10 - 30
Trimethylbenzene, 1,2,4- 95-63-6 5 - 10
Mica 12001-26-2 5 - 10
Calcium carbonate 471-34-1 5 - 10
Trimethylbenzene, 1,3,5 108-67-8 1 - 5
Cumene 98-82-8 1 - 5
Xylene 1330-20-7 1 - 5
Diethylbenzene 25340-17-4 1 - 5
Silica gel 63231-67-4 0.1 - 1
Crystalline silica 14808-60-7 0.1 - 1
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous Materials Information System ingredient disclosure list. See Section 8 for exposure limit guidelines.
SECTION 4: FIRST AID MEASURES
IF IN EYES: Flush eyes with plenty of water for at least 20 minutes retracting eyelids often. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention.
IF ON SKIN: Wash with soap and water. Get medical attention if irritation develops or persists.
IF VAPORS INHALED: Remove to fresh air. Restore breathing, if necessary. Call a physician if symptoms persist.
IF SWALLOWED: Do not induce vomiting. Seek medical attention immediately. Drink two glasses of water or milk to dilute. Do not give anything by mouth to an unconscious person.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: 43C; 109F TCC AUTOIGNITION TEMPERATURE: Not establishedLOWER EXPLOSIVE LIMIT (% in air): Not established UPPER EXPLOSIVE LIMIT (% in air): Not established EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide. UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and can travel to a source of ignition
and flash back.
-
Page 3 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-contained breathing apparatus and full protective equipment.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES
SPECIAL PROTECTION: Exposure to the spilled material may be irritating or harmful. Follow personal protective equipment recommendations found in Section 8 of this MSDS. Additional precautions may be necessary based on special circumstances created by the spill including; the material spilled, the quantity of the spill, the area in which the spill occurred. Evaporation of volatile substances can lead to the displacement of air creating an environment that can cause asphyxiation.
CLEAN-UP: Scrape up and place in disposal container. Shut off ignition sources; including electrical equipment and flames. Do not allow smoking in the area.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE
Handling: Harmful or irritating material. Avoid contacting and avoid breathing the material. Use only in a well ventilated area. Keep away from heat, sparks and flame. Wash thoroughly after handling. Keep container closed. Emptied container retains vapor and product residue. Observe all labeled precautions until container is cleaned. Drums of this material should be grounded when pouring. DO NOT CUT OR WELD ON OR NEAR THIS CONTAINER.
Storage: Store in a cool, dry, ventilated location. Keep away from heat and flame. Keep container closed.
Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
EYE PROTECTION: Wear safety glasses with side shields when handling this product. Wear additional eye protection such as chemical splash goggles and/or face shield when the possibility exists for eye contact with splashing or spraying liquid, or airborne material. Have an eye wash station available.
SKIN PROTECTION: Avoid skin contact by wearing chemically resistant gloves. Skin absorption may potentially contribute to the overall exposure to this material. Appropriate measures should be taken to prevent absorption so that the TLV is not invalidated.
GLOVES: Nitrile
RESPIRATORY PROTECTION: Respiratory protection may be required to avoid overexposure when handling this product. Use a respirator if general room ventilation is not available or sufficient to eliminate symptoms. NIOSH approved air purifying respirator with organic vapor cartridge. Respirators should be selected by and used following requirements found in OSHA's respirator standard (29 CFR 1910.134).
-
Page 4 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
VENTILATION: Use local exhaust ventilation or other engineering controls to minimize exposures.
EXPOSURE LIMITS:Chemical Name ACGIH EXPOSURE LIMITS OSHA PEL
Stoddard solvent 100 ppm TWA 500 ppm TWA; 2900 mg/m3 TWA
Aromatic petroleum distillate Not established Not established
Trimethylbenzene, 1,2,4- Not established Not established
Mica 3 mg/m3 TWA (respirable fraction) Not established
Calcium carbonate Not established 15 mg/m3 TWA (total dust); 5 mg/m3 TWA (respirable fraction)
Trimethylbenzene, 1,3,5 Not established Not established
Cumene 50 ppm TWA 50 ppm TWA; 245 mg/m3 TWA Skin absorption may potentially contribute to the overall exposure to this material.
Xylene 100 ppm TWA 150 ppm STEL
100 ppm TWA; 435 mg/m3 TWA
Diethylbenzene Not established Not established
Silica gel Not established Not established
Crystalline silica 0.025 mg/m3 TWA (respirable fraction) ((250)/(%SiO2 + 5) mppcf TWA (respirable)); ((10)/(%SiO2 + 2) mg/m3 TWA (respirable)); ((30)/(%SiO2 + 2) mg/m3 TWA (total dust))
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid COLOR: Aluminum ODOR: Solvent ODOR THRESHOLD: Not established WEIGHT PER GALLON (lbs.): 9.2 SPECIFIC GRAVITY: 1.09 SOLIDS (% by weight): 65.5
Not applicable pH: Not established FLASH POINT: 43C; 109F TCC BOILING POINT (deg. C): Not established FREEZING/MELTING POINT (deg. C): Not established VAPOR PRESSURE (mm Hg): Not established VAPOR DENSITY: Not established EVAPORATION RATE: Not established OCTANOL/WATER COEFFICIENT: Not established VOC, weight percent Not determined VOC, EPA Method 24, less water and exempt solvents
(theoretically determined) 384g/liter of material
-
Page 5 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal conditions. CHEMICAL INCOMPATIBILITY: Strong oxidizing agents HAZARDOUS POLYMERIZATION: Will not occur. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide
SECTION 11: TOXICOLOGICAL INFORMATION COMPONENT LD50/LC50 Stoddard solvent Not established
Aromatic petroleum distillate Oral LD50 Rat = 8400 mg/kg
Trimethylbenzene, 1,2,4- Oral LD50 Rat = 5 g/kg Inhalation LC50 Rat = 18000 mg/cu m/4H
Mica Not established
Calcium carbonate Oral LD50 Rat = 6450 mg/kg
Trimethylbenzene, 1,3,5 Inhalation LC50 Rat = 24000 mg/cu m/4H
Cumene Oral LD50 Rat = 1400 mg/kg Inhalation LC50 Mouse = 17500 mg/cu m/4H Dermal LD50 Rabbit = 12.3 ml/kg
Xylene Oral LD50 Rat = 4300 mg/kg Inhalation LC50 Rat = 5000 ppm/4H Dermal LD50 Rat = 1700 mg/kg
Diethylbenzene Oral LD50 Rabbit = 3 g/kg
Silica gel Not established
Crystalline silica Not established
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION
OVERVIEW: No ecological information available
SECTION 13: DISPOSAL CONSIDERATIONS
This product meets the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR 261. It is ignitable waste class D001. Disposal via incineration is recommended. Consult your state, local, or provincial authorities for more restrictive requirements. LAND DISPOSAL RESTRICTIONS: Xylenes (o-, m-, p- isomers)
SECTION 14: TRANSPORTATION INFORMATION
Consult Bill of Lading for transportation information. DOT: NOT REGULATED IATA: NOT REGULATED
SECTION 15: REGULATORY INFORMATION
INVENTORY STATUS U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements.
-
Page 6 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
CANADIAN CEPA DSL: The components of this product are included on the DSL or are exempt from DSL requirements.
EUROPEAN EINECS: As a result of the introduction of REACH into Europe, this product cannot be imported into Europe unless the REACH requirements are met.
AUSTRALIA AICS: This product is in compliance with the Australian Inventory of Chemical Substances requirements.
KOREAN TCCL: This product is in compliance with the Korean Existing Chemicals List requirements.
PHILIPPINES: This product is in compliance with the Philippine Inventory of Chemicals and Chemical Substances requirements.
If you need more information about the inventory status of this product call 651-236-5858.
This product may contain chemical substances that are regulated for export by various government agencies (such as the Environmental Protection Agency, the Bureau of Industry and Security, or the Drug Enforcement Administration, among others). Before exporting this product from the USA or Canada, we recommend you contact us at 651-236-5858 (USA) or 450-655-1306 x227 (Canada) to request an export review.
FEDERAL REPORTING EPA SARA Title III Section 313 Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372. EPA has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations. Chemical Name CAS# %1,2,4-Trimethylbenzene 95-63-6 5 - 10 Cumene 98-82-8 1 - 5 Xylene (mixed isomers) 1330-20-7 1 - 5
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous Materials Information System. B3 D2B D2A
STATE REPORTING This MSDS is not prepared for distribution in California.
SECTION 16: ADDITIONAL INFORMATION
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace Hazardous Materials Information System (WHMIS).
HMIS RATING: HEALTH -- 2 FLAMMABILITY -- 2 REACTIVITY -- 0 See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment recommendations.
Prepared by: The Global Regulatory Department
Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the information is derived from information provided to H.B.Fuller Construction Products, Inc. from its suppliers, and because H.B.Fuller Construction Products, Inc. has no control over the conditions of handling and use, H.B.Fuller
-
Page 7 of 711-04-2011802435PM
MATERIAL SAFETY DATA SHEET__________________________________________________________________________________________
Construction Products, Inc. makes no warranty, expressed or implied, regarding the accuracy of the data or the results to be obtained from the use thereof. The information is supplied solely for your information and consideration, and H.B.Fuller Construction Products, Inc. assumes no responsibility for use or reliance thereon. It is the responsibility of the user of H.B.Fuller Construction Products, Inc. products to comply with all applicable federal, state and local laws and regulations.