Appendices eaton fluids resistance_lr
-
Upload
axel-torres -
Category
Automotive
-
view
1.350 -
download
0
Transcript of Appendices eaton fluids resistance_lr
343EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
AppendicesIndex
Agency Listings 346Analyzing Hose Failures 360Fitting Assembly Torque Values 379
Flow Capacity Pressure Drop Chart 357Fluid Compatibility 349Hose Size to Maximum Operating Pressure 344
How to Identify and MeasureFluid Connectors 363Hydraulic Tubing Info 377
SAE Recommended Practices 356Service Life Routing Installation Instructions 359Technical Data 343
Alphabetical Index
DESCRIPTION PAGES DESCRIPTION PAGES DESCRIPTION PAGES DESCRIPTION PAGES
344 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
See pages 349-355 forFluid Compatibility
Hose tube identificationchart
1. Synthetic rubber
2. PTFE
3. Thermoplastic
4. AQP
5. Special application hose
6. EPDM
Hose Dash Size to Maximum Operating Pressure
Pressures expressed in psi/bar.
HOSE TO FITTING PAGE REFERENCE CHART
Hose Part HoseNumber Page Tube -02 -03 -04 -05 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48FC252 20 5 50/3 50/3 40/3 40/3 35/2FC352* 20 5 100/7 100/7 100/7 90/6 85/6 85/6 75/5 60/4 50/32550 21 5 225/162554 21 5 225/162570 21 5 225/16 225/16 225/16FC829 22 6 225/16FC629 21 1 225/16 225/162575 32 1 250/17 250/17 250/17 200/14 200/12FC647 33 1 360/25 300/21 300/21 250/17 250/172556 34 1 360/25 300/21 300/21 250/17 250/17FC332 33 4 250/17 250/17 250/17 250/17 250/172565 34 1 300/21 250/17 200/14 175/12 125/91531 22 5 300/21 300/21 300/21 300/211531A 22 5 300/212661* 35 4 300/21†† 250/17†† 200/14†† 150/10†† 100/7†† 62/4 56/4FC619 34 1 300/21†† 250/17†† 200/14†† 150/10†† 100/7†† 62/4 56/4CR170 28 5 350/24 350/24 350/24 350/24FC321 27 5 350/24 350/24 350/24 350/24 350/24 350/24 350/24FC498 36 4 400/28 400/28 400/28 350/24 350/24FC598 36 4 400/28 400/28 400/28 350/24 350/24FC466 35 1 400/28 400/28 400/28 350/24 350/24FC699 24 5 400/28 400/28 400/28 350/24 350/24 250/17302A 26 1 800/55 600/41 500/34 350/242580 37 1 1000/69 800/55 650/45 625/43 600/41 550/38 500/34 450/31 400/28 350/242583 37 1 1250/86 1125/78 1000/69 750/52 565/39 375/26FC650 24 4 1000/69 1000/69 1000/69 1000/69 1000/69FC364 31 2 1250/86 1100/76 1000/69 1000/69 750/52 500/34 100/7 100/7FC363 31 2 1250/86 1100/76 1000/69 1000/69 750/52 500/34FC355 23 4 1500/103 1500/103 1500/103 1250/86 1250/86 750/52 400/28 300/21 250/17 200/14FC234 25 5 1500/103 1500/103 1250/86 1250/86 750/52 400/28FC350 23 4 2000/138 1500/103 1500/103 1250/86 1250/86 750/52 400/28 300/21 250/17FC563 32 2 1250/86 1100/76 1000/69 1000/69 750/52 500/342808 30 2 2750/190 2500/172 1750/121 1500/103 1125/78 800/55FC465 29 2 3000/207 3000/207 3000/207 2500/172 2000/138 1500/103 1200/83 1000/69 625/432807 28 2 3000/207 3000/207 3000/207 2500/172 2000/138 1500/103 1200/83 1000/69 625/43S-TW 29 2 3000/207 3000/207 2500/172 2000/138 1500/103 1200/83 1000/69FC300 27 4 3000/207 3000/207 2250/155 2000/138 1750/121 1500/103 800/55 625/43 500/34 300/21 300/21FC611 40 6 3000/207 2250/155 2000/138 1250/86 1000/69 625/43 500/34 375/261503 26 1 3000/207 3000/207 2250/155 2000/138 1750/121 1500/103 800/55 625/43 500/34 350/24 350/242651 25 1 3000/207 3000/207 2250/155 2000/138 1750/121 1500/103 800/55 625/43 500/34 350/24 350/24303 26 1 3000/207 3000/207 2000/138 2000/138 1750/121 1500/103FC639/ 42FC839B 43 1 3000/207 3000/207 3000/207 3000/207 3000/207 3000/207† Pressure rating with reusable style fittings.‡ Pressure rating with Global crimp style fittings.§ 10,000 psi for static jack hose applications. See hose page for details.¥ 10,000 psi for water blast applications. See hose page for details.* See hose page for dash sizes not listed.†† 50 psi max with band clamp style fittings.
345EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
This table is intended as aguide in the selection ofhose by maximum operat-ing pressure. It is not aguarantee. Final selection isfurther dependent on fluidand ambient temperature,concentration of fluid, inter-mittent or continuous expo-sure, etc.
For further details on a specific hose see therespective catalog pages orcontact Eaton Corporationat 14615 Lone Oak Road,Eden Prairie, MN 55344USA 952/937-9800.
Hose Dash Size to Maximum Operating Pressure
Pressures expressed in psi/bar.
HOSE TO FITTING PAGE REFERENCE CHART
Hose Part HoseNumber Page Tube -02 -03 -04 -05 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48GH681 42 1 3000/207 3000/207 3000/207FC194 40 4 3250/224 3000/207 2500/172 2000/138 1750/121 1250/86 900/62GH194 39 4 3250/224 3000/207 2500/172 2000/138 1800/124 1300/90 900/62GH663 39 1 3250/224 3000/207 2500/172 1800/124 1300/90 950/66 725/50 580/40
2750/190† 2250/155† 2000/138† 1250/86† 1000/69†2681 38 1 4000/276 3250/224 3250/224 3000/207 2500/172 2000/138 1800/124 1300/90 900/62 700/48 600GH493 51 1 4000/276 4000/276 4000/276 4000/276 4000/276 3000/207 2500/172 2500/172FC323 50 4 3000/207 3000/207 3000/207 3000/207 3000/207FC324 50 4 4000/276 4000/276 4000/276FC469 30 2 4000/276 4000/276 3500/241FC849/ 43FC849B 44 0 4000/276 4000/276 4000/276 4000/276 4000/276FC310 41 1 5000/345 4000/276 3500/241 2750/190 2250/155 2000/138 1625/112FC693 46 6 5000/345 4000/276 3500/241GH120 45 1 5000/345 4000/276 3500/241 2750/190 2250/155 2000/138 1625/112 1250/86 1125/78FC510 41 4 5000/345 4000/276 3500/241 2750/190 2250/155 2000/138 1625/112FC325 50 4 5000/345 5000/345FC273/FC273B 54 1 5000/345 5000/345 5000/345 5000/345 5000/345FC659 52 1 4000/276 4000/276 4000/276 4000/276 4000/276 3000/207 2500/172 2500/172FC636 49 6 4000/276 4000/276 3000/207 2500/172FC735 46 1 5000/345 5000/345 4250/293 3625/250 3125/216 2500/172 2250/155FC736 53 1 5500/379 5000/345 5000/345 4000/276 4000/276 3000/207 2500/172 2500/172
4000/276‡ 4000/276‡ 4000/276‡
2766 45 1 5000/345 4000/276 3500/241 2250/155 2000/138 1625/112 1250/86 1000/692781 47 1 5000/345 4000/276 3500/241 3250/224 3000/207 2000/138 1625/112 1750/121 1250/86
5750/397‡ 5000/345‡ 4250/293‡ 3625/250‡ 3125/216‡ 2500/172‡ 2250/155‡1800/124‡ 1500/103‡
FC195 49 4 5000/345 4000/276 3500/241 2750/190 3000/207 2000/138 1625/112 1750/121 1250/865750/397‡ 5000/345‡ 4250/293‡ 3250/224‡ 3125/216‡ 2500/172‡ 2250/155‡1800/124‡ 1500/103‡
GH195 48 4 5750/397 5000/345 4250/293 3250/224 3000/207 2500/172 2250/155 1750/121 1500/103GH781 47 1 5750/400 5000/345 4250/293 3625/250 3125/216 2500/172 2250/155 1800/124 1300/90GH793 48 1 5750/397 5000/345 4250/293 3625/250 3125/216 2500/172 2250/155 1800/124 1300/90
5000/345† 4000/276† 3500/241† 2750/190† 2250/155† 2000/138†
GH506 55 1 6090/420 5510/380 5075/350 4250/293 3625/250FC254 53 1 7500/517¥ 6250/431 5000/345 4000/276 3000/207 3000/207GH466 55 1 5510/380FC606/FC606B 56 1 6000/414 6000/414 6000/414FC579*** 57 1 10000/690§ 10000/690§
† Pressure rating with reusable style fittings.‡ Pressure rating with Global crimp style fittings.§ 10,000 psi for static jack hose applications. See hose page for details.¥ 10,000 psi for water blast applications. See hose page for details.* See hose page for dash sizes not listed.†† 50 psi max with band clamp style fittings.***Based on 2:1 safety factor.
346 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Agency Listings
Government Agencies
DOT/FMVSS – US Department of Transportation, FederalMotor Vehicle Safety Standard
FDA – US Food and Drug Administration (tubes only)
MIL/DOD – US Military Specification, Dept. of Defense
MSHA – US Mine Safety and Health Administration
USCG/MMT – US Coast Guard, Merchant Marine Technical(SAE J1942 has replaced USCG approval)
DNV – Det Norske (Norwegian) Veritas
CGA – Canadian Gas Association
The listings below are intended only as guides in identifyingwhich Aeroquip hoses comply with requirements of variousagencies. For current and complete information, contactEaton.
Industry Agencies
AAR – American Association of Railroads
DIN – Deutsche (German) Industrial Norme (Replaced by EN)
EN – Committee for European Normalization
ABS– American Bureau of Shipping
SAE – Society of Automotive Engineers
UL – Underwriters Laboratories
ISO – International Standards Organization
★ = Approved details available from Eaton
*Listing may vary by hose style and size, some hoses mayrequire firesleeve or special procedures depending on spe-cific applications, contact Eaton for details.
GOVERNMENT INDUSTRY
HosePart DOT/ MIL/ USCG/Number Page FMVSS CGA DNV FDA* DOD MSHA MMT* ISO EN DIN AAR ABS SAE UL1503 26 100R5,
106 Type All ★ ★ J14021531 22 M6181531A 22 M6182550 21 106 Type AII ★ J140225542556 34 ★ ★
2565 34 MIL-H-13444Type I
2570 21 106 Type AII ★ J14022580 37 MIL-H-24136/3 ★ ★
2583 37 EN 854★ ★ Type R3 100R3
2651 25 ★ ★ ★ ★
2661 35 ★ ★ ★+ 100R42681 36 1436 EN 853 20 022
★ ★ ★ Type 1ST Type 1ST Type 1ST 100R1A2781 47 1436 EN 853 20 022
★ ★ ★ Type 1ST Type 2ST Type 2ST 100R2A2807 28 ★ ★ ★ 100R14A2808 30 ★ ★
302A 26 MIL-DTL-8794303 26 MIL-DTL-8794CR170 28 Type IIIFC194 40 1436 EN 856 20 022 100R1A,
★+ ★ ★ Type 1ST Type 1ST Type 1ST J1019FC195 49 1436 EN 856 20 022
★ ★ Type 2ST Type 1ST Type 1ST 100R2AFC234 25 J1527
★ ★ ★ ★ Type A1FC252 20★ = Approved details available from Eaton§ = In size -04 meets ISO 1436 Type R2AT+ = Firesleeve required. Contact Eaton for details.‡ = Does not meet in -04 size
347EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
Agency Listings
GOVERNMENT INDUSTRY
HosePart DOT/ MIL/ USCG/Number Page FMVSS CGA DNV FDA* DOD MSHA MMT* ISO EN DIN AAR ABS SAE ULFC254 53 ★ ★ ★ ★ 100R11FC273 54 3862 EN 856
★ ★ ★ Type R13 Type R13 ★ 100R13FC273B 54 3862 EN 856
Type R13 Type R13 100R13FC300 27 106 Type All 100R5,
J1019,★ ★ ★ J1402
FC310 41 EN 857★ ★ Type 1SC ★ 100R16
FC321 27 UL21FC323 50 100R11,
★ ★ ★ 100R12FC324 50 EN 856
★ ★ Type R12 ★ 100R12FC325 51 EN 856
★ ★ Type R13 100R13FC332 33 ★+FC350 23 106 Type All ★+ ★ ★ ★ J1402FC352 20 20R1FC355 23 106 Type All ★ J1402FC363 31 ★ ★
FC364 31 ★
FC465 29 100R14BFC466 35 EN 854
Type R6 100R6FC469 30FC498 36 ★ EN 854
Type R6 100R6FC510 41 EN 857
★ ★ Type 1SC 100R2ATFC563 32FC579 57 ★
FC598 36 100R6FC606 56 3862
★ Type R15 ★ 100R15FC606B 56 3862
Type R15 100R15FC611 40FC619 34 ★ ★+ 100R4FC629 21 106 Type All J1402FC636 49FC639 42 ★ ★ 100R17FC647 33FC650 24★ = Approved details available from Eaton.+ Firesleeve required. Contact Eaton for details.‡Applies only to hose that has suffered no damage, has been properly assembled with hose guards and tested to required proof test pressure.
348 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Agency Listings
GOVERNMENT INDUSTRY
HosePart DOT/ MIL/ USCG/Number Page FMVSS CGA DNV FDA* DOD MSHA MMT* ISO EN DIN AAR ABS SAE ULFC659 52 E3862 EN 856
★ ★ ★ Type R12 Type R12 ★ 100R12FC693 46FC699 24FC735 46 1436 20 022
Type 2SN§ Type 2SN ‡ 100R16FC736 53 3862 EN856
Type R12 Type R12 100R12S-TW 29 100R14AFC829 22 106 Type AII J1420FC839B 43 100R17FC849 43 ★ ★ ★
FC849B 44GH120 45 ★ 100R16GH194 39 1436 EN 853 20 022
★+ ★ Type 1SN Type 1SN Type 1SN ★ 100R1ATGH195 48 1436 EN 853 20 022
★ ★ Type 2SN Type 2SN Type 2SN ★ 100R2ATGH466 55 ★
GH493 51 3862 EN 856★ ★ ★ Type R12 TypeR12 ★ 100R12
GH506 55 3862 EN856 20 023★ ★ Type 4SH Type 4SH Type T2
GH663 39 1436 EN 853 20 022★ ★ ★†† Type 1SN Type 1SN Type 1SN ★ 100R1AT
GH681 42 ★ DIN20022Type 1
GH781 47 EN 857★ ★ ★ Type 2SC ★ 100R16
GH793 48 1436 EN 853 20 022★ ★ ★ Type 2SN Type 2SN Type 2SN ★ 100R2AT
★ = Approved details available from Eaton.+ Firesleeve required. Contact Eaton for details.†† = -4 thru -16 only
349EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
FluidCompatibility
Fluid compatibility
This chart indicates the suit-ability of various elastomersand metals for use with flu-ids to be conveyed. It isintended as a guide onlyand is not a guarantee.Final selection of the properhose style, seal, or materialof metal components is fur-ther dependent on manyfactors including pressure,fluid and ambient tempera-ture, concentration, dura-tion of exposure, etc.
How to use the chart
1. The chart has separatesections for rating elas-tomers for use as hoseinner tubes and as seals.Ratings for a given elas-tomer may not always bethe same in both sections.
2. Both the elastomer andthe metal must be consid-ered when determiningsuitability of a combinationfor a hose assembly,adapter with o-ring, swiveljoint or coupling.
3. Locate the fluid to beconveyed and determinethe suitability of the elas-tomeric and metal compo-nents according to theresistance ratings shownfor each.
4. Specific hose part num-bers can be found underthe inner tube materialgroupings in the Hose TubeIdentification Chart below.
5. Dimensional and operat-ing specifications for eachhose can be found on thecatalog pages shown witheach hose part number.
6. Information on o-ringsand seal options for swiveljoints and couplings, andhow to specify them, areshown in the respectivesections of this catalog.
7. For further details on theproducts shown in this cat-alog, and their applications,contact:
Eaton14615 Lone Oak RoadEden Prairie, MN 55344USA952/937-9800; Fax: 952/974-77221-888-258-0222www.hydraulics.eaton.com
Resistance key rating
E = Excellent – Fluid haslittle or no effect.
G = Good – Fluid hasminor to moderateeffect.
C = Conditional – Serviceconditions should bedescribed to EatonAeroquip for determi-nation of suitability forapplication.
U = UNSATISFACTORY
The differences betweenratings “E” and “G” are rel-ative. Both indicate satisfac-tory service. Where there isa choice, the materials rated“E” may be expected togive better or longer servicethan those rated “G”.
NOTE: Special precautionsare necessary in gaseousapplications due to thepotential volume ofgaseous fluid in the sys-tem. Unless the cover isperforated, hose styleswith rubber or thermoplas-tic covers are not suitablefor gases above 250 psi.Hose styles with perforatedcovers are so noted in theirconstruction descriptions.
WARNINGCompatibility of hose fittingswith conveyed fluid is anessential factor in avoidingchemical reactions that mayresult in release of fluids orfailure of the connection withthe potential of causingsevere personal injury orproperty damage.
Hose tube identification chart
1. Synthetic Rubber302A (p.26) 2781 (p.47) FC606 (p.56) GH120 (p.45)303 ( p.26) FC254 (p.53) FC647 (p.33) GH466 (p.55)1503 (p.26) FC273/ (p.54) FC659 (p.52) GH493 (p.51)2556 (p.34) FC273B (p.54) FC735 (p.46) GH506 (p.55)2565 (p.34) FC310 (p.41) FC736 (p.53) GH663 (p.39)2580 (p.37) FC466 (p.35) FC849/ (p.43) GH681 (p.42)2583 (p.37) FC579 (p.57) FC849B (p.44) GH781 (p.47)2651 (p.25) FC619 (p.34) FC849B (p.43) GH793 (p.48)2681 (p.38) FC639/ (p.42)
2. PTFE2807 (p.28) FC363 (p.31) FC465 (p.29) FC563 (p.32)2808 (p.30) FC364 (p.31) FC469 (p.30) S-TW (p.29)
3. Synflex Thermoplastic Elastomer (reference catalog E-HOOV-MC001-E)
4. AQP2661 (p.35) FC323 (p.50) FC350 (p.23) FC598 (p.36)FC194 (p.40) FC324 (p.50) FC355 (p.23) FC650 (p.24)FC195 (p.49) FC325 (p.51) FC498 (p.36) FC699 (p.24 )FC234 (p.25) FC332 (p.33) FC510 (p.41) GH194 (p.39)FC300 (p.27) FC598 (p.36) GH195 (p.48)
5. Special Application Hose (Not Included in Fluid Chart)FC234 FC650 Fuel (pp.25, 24)CR170 FC321 LPG (pp.27, 28)1531 1531A Railroad Air Brake (p.22)FC252 FC352 FC629 FC829 Silicone (p.20)2550 2554 2570 FC350 Truck Air Brake (pp.21-23)
6. EPDM RubberFC611 (p.40) FC636 (p.49) FC693 (p.46)
SEAL ELASTOMER DATA
Application Max. OperatingSeal Elastomer Specification Temperature RangeBuna-N† none –40°C to +121°C
[–40°F to +250°F]Neoprene none –54°C to +100°C
[–65°F to +212°F]EPR (Ethylene Propylene none –54°C to +149°CRubber)/EPDM [–65°F to +300°F]Viton* MIL-R-25897 –29°C to +204°C
[–15°F to +400°F]†Buna-N temperature range -65°F to +225°F. Also per MIL-R-6855.*Viton is a trademark of E.I. DuPont.
E = EXCELLENTG = GOODC = CONDITIONALU = UNSATISFACTORY
1 2 3 4 5 6FLUID HOSE SEALS METAL
Acetaldehyde U E C U G U C C U U G G E E E EAcetic Acid, 10% U E C C E U U E G U C U U C C UAcetic Acid, Glacial U E C C E U U C U U C U U C C CAcetone U E G U E U U G U U G E E E E EAcetophenone U E – U E U U E U U – E E E C EAcetyl Acetone U E U U E U U G U U G U C C C CAcetyl Chloride U E U U U U U U E U U C C C U EAcetylene1 G E G G E U U G E G G E E E E EAir, Hot (Up to +160°F)1 E E E E E E E E E E E E E E E EAir, Hot (161°F – 200°F)1 C E U E E G G E E G G E E E E EAir, Hot (201°F – 300°F)1 U E U C G U U G E U U E E E E EAir Wet, below 160°F1 E E C E E E E E E G C U G E E EAluminum Chloride, 10% aq E E E E E E E E E G E U U U U UAluminum Fluoride, 10% aq E E E U E E E E E G E U U U E CAluminum Nitrate, 10% aq E E E C E E E E E G E U U C C CAluminum Sulfate, 10% aq E E G E E E E E E – G U C E C CAlums, 10% aq E E E E E E E E E E E U C E C CAmmonia, Anhydrous1 C U U C E E E E U – – E U E E EAmmonia, Aqueous G G U C E E E E U – – E U E E EAmmonium Carbonate, 10% aq U E C U E U E E U – C C U C C CAmmonium Chloride, 10% aq E E C U E E E E U – – U U C U CAmmonium Hydroxide, 10% aq U E U U E C C E C U U G U C C UAmmonium Nitrate, 10% aq E E C U E E G E U G C G U G G UAmmonium Phosphate, 10% aq E E C U E E E E – G C U C G U GAmmonium Sulfate/Sulfide, 10% aq E E C U E E E E U G C U U G U GAmyl Acetate U E U U E U U G U U U E E E E EAmyl Alcohol G E E C E G C E G C E G G E U GAniline, Aniline Oil U E U U E U U G U U U E U E G GAniline Dyes U E U U E U G G G U U U C G C GAsphalt, < 200°F C E G G U G C U E G G E G E C EIRM 901 E E E E U E E C E E E E E E E EASTM #2 E E E E U E G U E G E E E E E EIRM 903 E E E E U E G U E G E E E E E EAutomatic Trans. Fluid 2 G E G G U E G U E C G E E E E EBarium Chloride, 10% aq E E C C E E E E E G C U G G G GBarium Hydroxide, 105 aq E E G C E E E E E E G G U G U GBarium Sulfide, 10% aq E E C C E E E E E G C C U G U UBenzene, Benzol U E U U U U U U E U C G E E G EBenzoic Acid U E C U U U U U E C C U G G G GBenzyl Alcohol U E C U E U G G E C C E G E G GBiodiesel (<180˚F) G E G C UBiodiesel (>180˚F) C E U U UBlack Sulfate Liquor G E C C E C C C E U C E C E U UBlast Furnace Gas C U C G U U U U E U C E C E U UBorax, 10% aq E E G C E G G E E G G E E E G –Boric Acid, 10% aq E E C E E G G G E G G U G C C CBrine G E C C C E G E E G C U G G U EBromine, Dry U E U U U U U U E U U U C U C CButane
1 LPG Approved E C U E – – E E E E EHose OnlyButyl Acetate U E U U E U U G U U C E E E E EButyl Alcohol E E G G C E E G E G G G G G G GButyl Cellosolve U E U U E U U G U U C E E E E EButylene (Butene)1 C E – C U C U U E U – E E E E EButyl Stearate U E – U U G U U E – – G G G G GButyraldehyde U E – U E U U G U U – E E E E GCalcium Acetate, 10% aq G E C C E G G E U U C G G G C GCalcium Bisulfate, 10% aq U E C G U E E U E G G U C C U UCalcium Chloride, 10% aq E E E C E E E E E E E G G G C G
This chart is intended for reference use onlyThe information in this chart pertains strictly to material compatibility and is not intended to be used as an application guide.For information on specific applications not included in this catalog, please contact Eaton Aeroquip.
Synt
hetic
Rub
ber
PTFE
Ther
mop
last
ic E
last
omer
AQ
PSp
ecia
l App
licat
ion
Hose
EPD
MB
una-
NN
eopr
ene
EPR
Vito
n*U
reth
ane
Hyt
rel
Stee
lB
rass
Stai
nles
s St
eel
Alu
min
umM
onel
E = EXCELLENTG = GOODC = CONDITIONALU = UNSATISFACTORY
1 2 3 4 5 6FLUID HOSE SEALS METAL
Calcium Hydroxide, 10% aq E E C C E E E E E U C G G G U GCalcium Hypochlorite, 10% aq C E C U E U U E E U C U G C U UCalcium Nitrate, 10% aq E E E G E E E E E E E G G G G GCarbitol G E G C G G G G G U G E E E E ECarbolic Acid (Phenol) U E U U C U U G E U U U E E – –Carbonic Acid C E C U E G E E E C C U C E G ECarbon Dioxide, Dry gas1 E E E E E G G E E G E E E E E ECarbon Disulfide U E U U U U U U E C C G G G E GCarbon Monoxide1 E E E E E G G E E G E E E E E ECarbon Tetrachloride U E U U U U U U E U U U G G U ECastor Oil E E G E G E E G E G G E E E E ECellosolve Acetate U E U U E U U G U U U U U E G EChina Wood Oil (Tung Oil) E E C C U G G U E U C E G E E EChlorine1 U G U U U U U U G U U C C C C CChloroacetic Acid U E U U E U U G U U U U U U U GChloroacetone U E U U E U U E U U U G G G U GChlorobenzene U E U U U U U U G U U G G G G GChloroform U E U U U U U U E U U G G G G GO-Chlorophenol U E U U U U U U E U U G G G U GChlosulfonic Acid U U U U U U U U U U U G U G G CChrome Plating Solution U E – U U U U G E U – C U U U UChromic Acid U E – U C U U C E U – C U U U UCitric Acid G E C G E E E E E E C C C C C CCoke Oven Gas U E – U U U U U E U – E C E U UCopper Chloride, 10% aq E E E G E E E E E G E U U U U UCopper Cyanide, 10% aq E E – G E E E E E E – E U G U GCopper Sulfate, 10% aq E E G G E E E E E G G U C G U GCotton Seed Oil E E E G C E G C E E E E E E E ECreosote (Coal Tar) G E U G U G C U E U U E C E E ECrude Oil G E C E U E G U E G C G U G U UCyclohexanol C E C G U E G U E C C E E E C ECyclohexanone U E C U G U U G U G G E E E C EDetergent/Water Solution E E C G E E E E E C C G E E E EDiacetone Alchohol (Acetol) U E U U E U U E U C C E E E E EDibenzyl Ether U E – U G U U G U – – G G G G GDiesel Oil 2 G E C G U E C U E C C E E E E EDiethylamine C E – C C G G G U – – E U E – EDioctyl Phthalate (DOP) U E C C G U U G G C C E E E E EDowtherm A&E U E – U U U U U E – – G U E E EEthyl Alcohol (Ethanol) E E C G E E E E E C C E E E G EEthyl Acetate U E C U G U U G U C C E E E E EEthyl Benzene U E – U U U U U E U – E G G G EEthyl Cellulose G E U U G G G G U C C E G G G GEthyl Chloride C E U U U U U U E U U E E E G GEthylene Dichloride U E U U U U U U G U U G C G G GEthylene Glycol E E C G E E E E E C C U G E E EFerric Chloride, 10% aq E E – G E E G E E – – U U U U UFerric Nitrate, 10% aq E E C E E E E E E C C U U G U UFerric Sulfate, 10% aq E E C E E G G G E C C U U E U UFormaldehyde U E C U E C C G G C C E E E G GFormic Acid G E U C E C G E U U U U C C C CFuel Oil E E G E U E G U E G G E E E E EFurfural U E – U G C C G U U – G G G G GGallic Acid, Solution G E – C G G G G E U – U – G C GGasoline 2 G E E G U E C U E E E E E E E EGasohol 2 G E G C U G G U E E E E E E G EGlycerine/Glycerol E E E E E E E E E G E E G E E EGreen Sulfate Liquor G E – U E G G E E – – U U E U UHelium 1 E G C E E E E E E E E E E E E E
*Viton is a E.I. DuPont trademark.Note 1 - Rubber-covered hose must be perforated to allow gas to escape.Note 2 - Due to the widely different additives in these fluids, testing should be done on the actual fluid being considered.
Synt
hetic
Rub
ber
PTFE
Ther
mop
last
ic E
last
omer
AQ
PSp
ecia
l App
licat
ion
Hose
EPD
MB
una-
NN
eopr
ene
EPR
Vito
n*U
reth
ane
Hyt
rel
Stee
lB
rass
Stai
nles
s St
eel
Alu
min
umM
onel
350 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
FluidCompatibility
E = EXCELLENTG = GOODC = CONDITIONALU = UNSATISFACTORY
1 2 3 4 5 6FLUID HOSE SEALS METAL
Natural Gas1 LPG Approved E E U E – – G G G G G
Hose Only
Nickel Acetate, 10% aq G C U G E C C E G U U G C E G ENickel Chloride, 10% aq E E U E E E G E E U U U U G U GNickel Sulfate, 10% aq E E U E E E E E E U U U G G U GNitric Acid, to 10% U E U U G U U U E U C U U E U UNitric Acid, over 10% U C U U U U U U G U U U U E C UNitrobenzene U E U U E U U U G U U E G E E ENitrogen1 E E E E E E E E E E E E E E E EOctyl Alcohol C E E U U E E E E E E E E E E EOleic Acid G E G U U U U C G G E C E G C GOrtho-Dichlorobenzene U E – U U U U U E – – G G G G GOxalic Acid, 10% aq C E C C E G G E E C C U C C C COxygen1 U U U U E – – – – – – G G G G GPalmitic Acid E E E E G E G G E – E G – E G GPara-Dichlorobenzene U E – U U U U U E – – G G G G GPentane
1 LPG Approved E E U E U G G G G E GHose Only
Perchloric Acid U E U U G E G G E U U U U U U UPerchloroethylene U E U U U U U U E U U C G G G EPetroleum Base Oils G E E E U E G U E E E E E E E EPhenol (Carbolic Acid) U E U U U U U G E U U U E E E GPhosphate Ester 2 U E C U E U U G C U G E E E E EPhosphoric Acid 20% U E U U E U U G E U U U E U C EPhosphorous Trichloride U E U U E U U E E U U C U C E EPotassium Acetate, 10% aq G E – G E G G E U – – C G C U GPotassium Chloride, 10% aq E E E E E E E E E E E E C E U GPotassium Cyanide, 10% aq E E E G E E E E E E E C U G U CPotassium Dichromate, 10% aq E E E E E E E E E E E C C C C CPotassium Hydroxide, to 10% G E C C E G G E G C C G G G U EPotassium Hydroxide, over 10% C E U C E C C E U U U G G G U EPotassium Nitrate, 10% aq E E E E E E E E E E E G G E G –Potassium Sulfate, 10% aq E E E E E E E E E E E – – – – –Propane
1(Liquified) LPG Approved C – – – – – E E E E E
Hose Only
Propyl Acetate U E – U G U U G U – – E – E E EPropyl Alcohol E E U E E E E E E U U E E E E EPropylene1 U E – U U U U U E – – E E E E ERefrigerant R-121 E – G C C G E C E E E E E E E ERefrigerant R-131 E – G C G G E C E E E E E E E ERefrigerant R-221 U C U U E U E C U U U E E E E ERefrigerant R-134a1 C C U U E E C U U U E E E E E ESewage G E E G E E E E E U E G G G G GSilicone Oils G E E G E E E E E E E E E E E ESoap (Water Solutions) E E C E E E E E E C C E E E U ESodium Acetate, 10% aq G U – G E G G E U – – E E G E ESodium Bicarbonate, 10% aq E E E E E E E E E E E G G E G ESodium Borate, 10% aq E E E E E E E E E E E E E E G –Sodium Carbonate, 10% aq E E E E E E E E E E E E G E U ESodium Chloride, 10% aq E E E G E E E E E E E U C C C ESodium Cyanide, 10% aq E E E E E E E E E E E E – C U USodium Hydroxide, to 10% C E G C E U G E E G G C G C U CSodium Hydroxide, over 10% U E C U E U U G E C C C C C U C
*Viton is a E.I. DuPont trademark.Note 1 - Rubber-covered hose must be perforated to allow gas to escape.Note 2 - Due to the widely different additives in these fluids, testing should be done on the actual fluid being considered.
351EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
FluidCompatibility
E = EXCELLENTG = GOODC = CONDITIONALU = UNSATISFACTORY
1 2 3 4 5 6FLUID HOSE SEALS METAL
Heptane E E E C U E G U E G G E E E E EHexaldehyde U E – U E U G G U U – G G E E GHexane E E E E U E G U E G G E E E E EHydraulic Oils 2
Ester Blend C E C G C E U U E U E E E E E EPhos. Ester/Petroleum Blend U E C U U U U U C U G E E E E ESilicone Oils E E E E E E E E E E E E E E E EStraight Petroleum Base E E E E U E G U E E E E E E E EStraight Phosphate Ester U E C U E U U G C U G E E E E EWater Glycol E E C G E E E E E C C E E E G EWater Petroleum Emulsion E E C G U E G U E C C C E E G E
Hydrobromic Acid U E U E G U U E E U U E U E E UHydrochloric Acid, Cold U E U U G U U G E U U U U U U UHydrocyanic Acid C E – U E C C E E – – E E G E GHydrofluoric Acid U E U U U U U C U U U U U U U CHydrofluorosilic Acid E E – G G G G E E – – U U U U UHydrogen1 G C G G E E E E E E E E E E E EHydrogen Peroxide C E G C G G G G E G G U U G E UHydrogen Sulfide, Dry C C C U E U G E U – G E G G G GIsocyanate U E U U U U U G E U U G – G – –Iso Octane G E E G U E G U E G E E E E E EIsopropyl Acetate U E C U C U U G U U C E – E E EIsopropyl Alcohol G E C G E G G E E U C E E E G EIsopropyl Ether G E – C U G U U U C – G G G – –JP-4, JP-5 E E G E U E U U E U G E E E E EKerosene G E G E U E U U E U G E E E E ELacquer/Lacquer Solvents U E U U E U U U U U G U E E E ELime Sulfur U E C U E U E E E C C G U G – ULinseed Oil E E G G U E G U E G G E E E E ELPG
1 LPG Approved E G U E – – E E E E EHose Only
Lubricating Oils2 See Hydraulic Oils See Hydraulic Oils See Hydraulic Oils
Magnesium Chloride, 10% aq E E C E E E E E E C C E C C G GMagnesium Hydroxide, 10% aq G E C G E G G E E C C E G E G GMagnesium Sulfate, 10% aq E E C E E E E E E C C E E E E EMaleic Acid U E C C G U U U E C C E G G G GMaleic Anhydride U E C U C U U U E C C G U E G EMalic Acid G E – G U G G U G – – U – E G EMercuric Chloride G E E G G E E E E E E U U U U UMercury E E E E E E E E E E E E U E U GMethanol E E C E E G G E U C C G G E C EMethyl Bromide C E U U U G U U E U U E E G U EMethyl Chloride U E U U U U U U E U U E E E U GMethyl Butyl Ketone U E U U E U U E U C C E E E – EMethyl Ethyl Ketone U E U U E U U E U U G G G G G GMethylene Chloride U E U U U U U U G U U G G G G GMethyl Isobutyl Ketone U E U U E U U U U U U G G G G GMethyl Isopropyl Ketone U E U C E U U U U U U G G G G GMethyl Salicylate U E – U C U U C U – – E G G E GMIL-L-2104 E E E E U E G U E E E E E E – EMIL-H-5606 E E E E U E G U E E E E E E E EMIL-H-6083 E E E E U E E U E E E E E E – EMIL-L-7808 G E G G U G U U E G G G G E – –MIL-L-23699 E E – G U G U U E – – E E E E EMIL-H-46170 G E – G C E G U E – – E E E – EMIL-H-83282 G E – G U E U U E – – E E E – EMineral Oils E E G E U E G U E G G E E E E ENaphtha C E G E U C U U E C G – – – – –Naphthalene U E U U U U U U E C G E G E G GNaphthenic Acid U E – U U C U U E – – – G E G G
This chart is intended for reference use onlyThe information in this chart pertains strictly to material compatibility and is not intended to be used as an application guide.For information on specific applications not included in this catalog, please contact Eaton Aeroquip.
Synt
hetic
Rub
ber
PTFE
Ther
mop
last
ic E
last
omer
AQ
PSp
ecia
l App
licat
ion
Hose
EPD
MB
una-
NN
eopr
ene
EPR
Vito
n*U
reth
ane
Hyt
rel
Stee
lB
rass
Stai
nles
s St
eel
Alu
min
umM
onel
Synt
hetic
Rub
ber
PTFE
Ther
mop
last
ic E
last
omer
AQ
PSp
ecia
l App
licat
ion
Hose
EPD
MB
una-
NN
eopr
ene
EPR
Vito
n*U
reth
ane
Hyt
rel
Stee
lB
rass
Stai
nles
s St
eel
Alu
min
umM
onel
352 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
FluidCompatibility
E = EXCELLENTG = GOODC = CONDITIONALU = UNSATISFACTORY
1 2 3 4 5 6FLUID HOSE SEALS METAL
Sodium Hypochlorite, 10% aq C E C G G C C E C C C U U U U CSodium Metaphosphate, 10% aq E E E E E E E E E E E E G G U GSodium Nitrate, 10% aq G E E G E G G E – E E E C E E ESodium Perborate, 10% aq G E – G E G G E E – – C U C U CSodium Peroxide, 10% aq G E – G G G G E E U – U U C C CSodium Phosphates, 10% aq E E E C E E E E E E E U E G U ESodium Silicate, 10% aq E E E G E E E E E E E E E E E ESodium Sulfate, 10% aq E E E G E E E E E E E C G G G GSodium Sulfide, 10% aq E E E G E E E E E E E C U C U GSodium Thiosulfate, 10% aq G E E G E G E E E E E U U C G ESoy Bean Oil E E G C U E G U E G G E E E E EStannic Chloride G E C G E E G E E C C U U U U USteam1 (up to 388°F) U E U U G U U C C U U E E E G EStearic Acid G E G G G G G G E G G C C E C EStoddard Solvent G E U C U E G U E U U E E E E EStyrene U E U U U U U U G U U E E E E ESulfur, Slurry C E G E E U E E E G G E U G E ESulfur Chloride, Wet U E – U U U U U E – – G – G G USulfur Dioxide, Dry1 U E U U E U U G E U U E G G E GSulfuric Acid, to 10% U E U U E U G U E C C U G C – ESulfuric Acid, over 10% U E U U U U U U G U U C C C U CSulfurous Acid U E U G G C C U G U U U C C C UTannic Acid G E G G E G E E E G G E E E C ETar (Bituminous) G E G G U G U U E G G E G E E ETartaric Acid E E G E G E G G E G G U C C E ETertiary Butyl Alcohol G E G E G G G G E G G G G G G GTitanium Tetrachloride U E – U U C U U E – – E U G UToluene (Toluol) U E U U U U U U E U U E E E E ETrichlorethylene U E U U U U U U E U U E G E E ETricresyl Phosphate U E U U E U U E G U U E – C – GTriethanolamine G E U G E E U E U U U E U E E ETung Oil E E C C U G G U E U C E G E E ETurpentine E E G G U G U U E G G G G G G GVarnish C E G G U G U U E G G E G E E EVinyl Chloride U E U U U U U U E U U E U C E EWater (to +150°F) E E E G E E E E E E E C G E G EWater (+151°F to +200°F) C E U C E E E E E U U C G E G EWater (+201°F to +350°F) U E U U E U U G G U U C G E G EWater Glycol E E C E E E E E E C C E E E G EWater Petroleum Emulsion2 E E C C U E G U E C C C E E G EXylene U E C U U U U U E U C E E E E EZinc Chloride, 10% aq E E E E E E E E E E E E U U C GZinc Sulfate, 10% aq E E – E E E E E E – – U C G C G
This chart is intended for reference use onlyThe information in this chart pertains strictly to material compatibility and is not intended to be used as an application guide.For information on specific applications not included in this catalog, please contact Eaton Aeroquip.
*Viton is a E.I. DuPont trademark.Note 1 - Rubber-covered hose must be perforated to allow gas to escape.Note 2 - Due to the widely different additives in these fluids, testing should be done on the actual fluid being considered.
Synt
hetic
Rub
ber
PTFE
Ther
mop
last
ic E
last
omer
AQ
PSp
ecia
l App
licat
ion
Hose
EPD
MB
una-
NN
eopr
ene
EPR
Vito
n*U
reth
ane
Hyt
rel
Stee
lB
rass
Stai
nles
s St
eel
Alu
min
umM
onel
Hydraulic fluids & lubricating oils
The following is a represen-tative list of fluids and man-ufacturers. The fluids aregrouped under generic“family” heads andarranged alphabetically. Foreach generic “family” listingwe have included maximumfluid temperature recom-mendations for the fourhose classifications on page349 (1 through 4). Two maxi-mum fluid temperature rat-ings are listed under desig-nations of “H” and “LP”.
The “H” designation is forhydraulic service up to themaximum rated operatingpressure of any particularhose in the classification.The “LP” designation is forlow-pressure service suchas lubricating oil systems orlow-pressure hydraulicreturn lines.
The letter “U” in the boxindicates unsatisfactoryresistance to the fluid type.
Fluid temperature ratingsare predicated on maximumallowable ambient tempera-tures as follows:
Classifications 1 and 3(Synthetic Rubber andThermoplastic Elastomer)
“H” fluid temp. ratings:+140°F ambient
“LP” fluid temp. ratings:+180°F ambient
Classification 2 (PTFE)
“H” fluid temp. ratings:+400°F ambient
“LP” fluid temp ratings:+400°F ambient
Classification 4 (AQP)
“H” fluid temp. ratings:+160°F ambient
“LP” fluid temp. ratings:+250°F ambient
(If “H” fluid temperature is+225°F or less, allowableambient temperature maybe increased to +200°F)
Ambient temperatures inexcess of those recom-mended, in conjunctionwith maximum fluid tem-peratures, can materiallyshorten the service life ofthe hose.
CAUTION: The fluid manu-facturer’s recommendedmaximum operating tem-perature for any specificnamebrand fluid should bescrupulously observed bythe user. These recom-mended temperatures canvary widely between namebrands of different fluidcompositions, even thoughthey fall into the samegeneric “family” of fluids.
Exceeding the manufactur-er’s recommended maxi-mum temperature canresult in fluid breakdown,producing by-products thatare harmful to elastomericproducts, as well as othermaterials in the system. If amanufacturer's recommend-ed maximum temperaturefor his specific fluid is lowerthan that for the hose rat-ing, it should take prece-dence over the hose ratingfor service usage.
353EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
FluidCompatibility
STRAIGHT PETROLEUM-BASE
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Aircraft Hydraulic Oil AAAmbrex OilsArco A.T.F. Dexron Arco A.T.F. Dexron IVArco A.T.F. Type FArco Fleet MotorArco H.T.F. C-2 FluidArco H.T.C. 100 FluidArco 303 FluidATF SpecialAutomatic TransmissionFluid (Dexron)
Carnea OilsCitgo AmplexCitgo ATF, Type FCitgo ATF, DexronCitgo Extra Duty CirculatingOils Mineral Oil (Heavy Duty) (R & O)Citgo Motor OilsCitgo Pacemaker SeriesMineral Oil (R & O)Citgo Pacemaker T SeriesMineral Oil (R & O)Citgo Pacemaker XD SeriesMineral Oil (Heavy Duty) (R & O)Citgo SentryCitgo Tractor Hydraulic FluidConoco 303 FluidCustom Motor Oil
Dectol R & O OilsDelo 400 Motor OilsDelvac OilsDelvac SHCDelvac Special 10W-30
Donax T OilsDTE OilsDuroDuro AW
EP Hydraulic OilsEP Industrial OilsEP Machine OilsEnergol HL68Energol HLP C68Etna OilsExxon ATF
Factovis 52 – Conventional R & O Hydraulic Fluid
Gulf Harmony AWGulf Security AWGlide
Hulburt 27 SeriesHydraulic SeriesHydraulic OilsHydroil Series
Industron 53 – Anti WearHydraulic Fluid
Lubrite Motor 20W-40
Mobil AFT 210Mobil AFT 220Mobilfluid 62Mobilfluid 423Mobil Hydraulic OilsMobiloil SpecialMobiloil Super 10W-40
NUTO Oils
OC Turbine Oils
Peaco OilsPennbell OilsPower-Tran Fluid
Quadroil Series
Rando OilsRando Oils HDRedind OilsRegal Oils R & ORimula OilsRotella OilsRotella T OilsRPM Delo 200 Motor OilsRPM Delo 300 Motor OilsRPM Delo Special Motor OilsRubilene
Shell Brand Special Motor OilsSun R & O OilsSuntac HP OilsSuntac WR OilsSunvis 700 OilsSunvis 800 OilsSunvis 900 OilsSuper Hydraulic OilsSupreme Motor Oils
Tellus OilsTeresstic OilsTorque FluidsTorque Fluid 47Torque Fluid 56Tractor Hydraulic Fluid
Union ATF DexronUnion ATF Type FUnion C-2 FluidUnion C-P OilUnion Custom Motor OilUnion Gas Engine OilUnion Guardol Motor OilUnion Heavy Duty Motor OilUnion Hydraulic Oil AWUnion Hydraulic Tractor FluidUnion Premium Motor OilUnion S-1 Motor OilUnion Special Motor OilUnion Super Motor Oil
Union Torque CorrectionFluidUnion Turbine OilUnion Turbine Oil XDUnion UnaxUnion Unax AWUnion Unax R & OUnion Unax RXUnion Unitec Motor OilUnivis J13Univis J26Univis P32
Vactra OilsVitrea Oils
Way Lubricants
XD-3 Motor Oils
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H +200˚F +400˚F +200˚F +300˚FLP +250˚F +450˚F +200˚F +300˚F
354 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
FluidCompatibility
WATER AND PETROLEUMOIL EMULSION (FR)
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Fluid NameAqualubeAstrol #587
Chevron FR Fluid DChrysler L-705Citgo Pacemaker Invert FRFluidConoco FR Hydraulic Fluid
Dasco IFRDuro FR-HD
Fire Resistant HydrafluidFire Resistant HydraulicFluid BFR 3110 Hydraulic Fluid(invert)Fyre-Safe W/O
Gulf R & D FR Fluid
Houghto-Safe 5046Houghto-Safe 5046WHulsafe 500Hy-Chock OilHydrasol A
Ironsides #814-AIrus Fluid 905
Kutwell 40
Masol Fire Resistant FluidMeltran FR 900
Mine GuardMobilmet S122
Penn Drake Hydraqua FluidPermamul FRPuro FR FluidPyrogard CPyrogard D
Quintolubric 957 SeriesQuintolubric 958 Series
Regent Hydrolube #670
SAFOIL Hydraulic Fluid Anti-WearSinclair Duro FR-HDSolvac 1535GStaysol FRSunsafe F
Union FR FluidUnion Soluble Oil HD
Veedol Auburn FRHVeedol Auburn FRHConcentrate
WATER AND GLYCOLSOLUTION
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Chem-Trend HF-18Chem-Trend HF-20Chevron Glycol FR FluidsCitgo Glycol FR FluidsCitgo Glycol FR-20 XDCitgo Pacemaker
Dasco FR 150Dasco FR 200Dasco FR 200 BDasco FR 310
Fyrguard 150Fyrguard 200Fyre-Safe 225
Gulf FR Fluid G-200Gulf FR Fluid – G Series
Houghto-Safe 271Houghto-Safe 416Houghto-Safe 520Houghto-Safe 525Houghto-Safe 616Houghto-Safe 620Houghto-Safe 625Houghto-Safe 640Hydra Safe 620Hydra Safe 625Hydraulic Safety Fluid 200Hydraulic Safety Fluid 300Hyspin AF-1
Hyspin AF-2Hyspin AF-3
MaxmulMaxmul FRMelsyn 200Melsyn Glycol FR
Nyvac FR FluidNyvac FR 200 FluidNyvac 20 (WG)Nyvac 30 (WG)
Park Water Glycol HydraulicFluidPennzoil Fluid FR 2X
Quintolubric 700 Series
Santosafe W/G 15Santosafe W/G 20Santosafe W/G 30Standard Glycol FR #15Standard Glycol FR #20Standard Glycol FR #25
Ucon Hydrolube 150 CPUcon Hydrolube 200 CPUcon Hydrolube 275 CPUcon Hydrolube 300 CPUcon Hydrolube 550 CPUcon Hydrolube 900 CPUcon Hydrolube 150 DBUcon Hydrolube 275 DBUcon Hydrolube 150 LTUcon Hydrolube 200 LT
Ucon Hydrolube 275 LTUcon Hydrolube 300 LTUcon M-1Ucon Hydrolube 200 NMUcon Hydrolube 300 NM
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H +200˚F +250˚F +150˚F +200˚FLP +200˚F +250˚F +150˚F +200˚F
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H +200˚F +250˚F +150˚F CLP +200˚F +250˚F +150˚F C
355EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
FluidCompatibility
STRAIGHT PHOSPHATE-ESTER (FR)
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
FR FluidsFyrquel 90Fyrquel 150Fyrquel 220Fyrquel 300Fyrquel 550Fyrquel 1000Fyrquel 150 R & OFyrquel 220 R & OFyrquel 550 R & O
Gulf FR Fluid P-37Gulf FR Fluid P-40Gulf FR Fluid P-43Gulf FR Fluid P-45Gulf FR Fluid P-47
Houghto-Safe 1010Houghto-Safe 1055Houghto-Safe 1115Houghto-Safe 1120Houghto-Safe 1130
Pyrogard 51Pyrogard 53Pyrogard 55
Safetytex 215
Skydraul 500ASkydraul 7000
Univis P12
ESTER BLEND TURBINEOILS
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Stauffer Jet IStauffer Jet II
SILICONE OILS
Maximum fluid temperaturerecommendation. See CAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Dow Corning 200 Fluid (100CS)Dow Corning QF1-2023Dow Corning 4-3600Dow Corning 3-3672
POLYOL-ESTER
Maximum fluid temperaturerecommendation. SeeCAUTION on page 349 for maximum fluid tempera-tures and limiting ambienttemperatures.
Fluid Name
Quintolubric 822 Series
LUBRICANT COMPATIBILITY CHART
Hose StyleLubricant FC802 FC505 FC555 FC558 GH134 FC665 FC765Mineral Oil Y Y Y N N Y YPAG Y Y Y Y Y Y YEster Oil Y Y Y Y Y Y YAlkylbenzene Y Y Y N N Y YY = CompatibleN = Non-compatible
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4 6
H U +400˚F +200˚F U 200LP U +400˚F +200˚F U 200
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H - - - -LP +250˚F +450˚F +200˚F +300˚F
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H +200˚F +400˚F +200˚F +300˚FLP +250˚F +450˚F +200˚F +300˚F
HOSE CLASSIFICATIONS (SEE P. 349)1 2 3 4
H +150˚F +400˚F - +150˚FLP +200˚F +400˚F - +250˚F
356 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
SAE Recomended PracticesSelection, installation and maintenance of hose andassemblies — SAE J1273 October 1996The following recommendationson selection, installation andmaintenance of hose assemblieswas established by the S.A.E. in1991. Please read these generalinstructions carefully. Moredetailed information on many ofthese subjects is covered in thiscatalog.
1. Scope—Hose (also includes hoseassemblies) has a finite life and thereare a number of factors which willreduce its life.
This recommended practice isintended as a guide to assist systemdesigners and/or users in the selec-tion, installation, and maintenance ofhose. The designers and users mustmake a systematic review of eachapplication and then select, install,and maintain the hose to fulfill therequirements of the application. Thefollowing are general guidelines andare not necessarily a complete list.
WARNING: IMPROPER SELECTION,INSTALLATION, OR MAINTENANCEMAY RESULT IN PREMATURE FAIL-URES, BODILY INJURY, OR PROP-ERTY DAMAGE.
2. References
2.1 Applicable Documents—The fol-lowing publications form a part of thisspecification to the extent specifiedherein. The latest issue of SAE publi-cations shall apply.
2.1.1 SAE PUBLICATIONS—Availablefrom SAE, 400 CommonwealthDrive, Warrendale, PA 15096-0001.
J516—Hydraulic Hose Fittings
J517—Hydraulic Hose
3. Selection—The following is a listof factors which must be consideredbefore final hose selection can bemade.
3.1 Pressure—After determining thesystem pressure, hose selectionmust be made so that the recom-mended maximum operating pres-sure is equal to or greater than thesystem pressure. Surge pressureshigher than the maximum operatingpressure will shorten hose life andmust be taken into account by thehydraulic designer.
3.2 Suction—Hoses used for suctionapplications must be selected toinsure the hose will withstand thenegative pressure of the system.
3.3 Temperature—Care must betaken to insure that fluid and ambienttemperatures, both static and tran-sient, do not exceed the limitations ofthe hose. Special care must be takenwhen routing near hot manifolds.
3.4 Fluid Compatibility—Hoseselection must assure compatibilityof the hose tube, cover and fittingswith the fluid used. Additional cautionmust be observed in hose selectionfor gaseous applications.
3.5 Size—Transmission of power bymeans of pressurized fluid varieswith pressure and rate of flow. Thesize of the components must be ade-quate to keep pressure losses to a
minimum and avoid damage to thehose due to heat generation orexcessive turbulence.
3.6 Routing—Attention must begiven to optimum routing to minimizeinherent problems.
3.7 Environment—Care must betaken to insure that the hose and fit-tings are either compatible with orprotected from the environment towhich they are exposed.Environmental conditions such asultraviolet light, ozone, salt water,chemicals, and air pollutants cancause degradation and premature fail-ure and, therefore, must be considered.
3.8 Mechanical Loads—Externalforces can significantly reduce hoselife. Mechanical loads which must beconsidered include excessive flexing,twist, kinking, tensile or side loads,bend radius, and vibration. Use ofswivel-type fittings or adapters maybe required to insure no twist is putinto the hose. Unusual applicationsmay require special testing prior tohose selection.
3.9 Abrasion—While hose isdesigned with a reasonable level ofabrasion resistance, care must betaken to protect the hose fromexcessive abrasion which can resultin erosion, snagging and cutting ofthe hose cover. Exposure of the rein-forcement will significantly acceleratehose failure.
3.10 Proper End Fitting—Care mustbe taken to insure proper compatibili-ty exists between the hose and cou-pling selected based on the manufac-turer’s recommendations substantiat-ed by testing to industry standardssuch as SAE J517. End fitting compo-nents from one manufacturer areusually not compatible with end fit-ting components supplied by anothermanufacturer (i.e., using a hose fit-ting nipple from one manufacturerwith a hose socket from anothermanufacturer). It is the responsibilityof the fabricator to consult the manu-facturer’s written instructions or themanufacturer directly for proper endfitting componentry.
3.11 Length—When establishingproper hose length, motion absorp-tion, hose length changes due to pres-sure, as well as hose and machine tol-erances must be considered.
3.12 Specifications andStandards—When selecting hose,government, industry and manufac-turers’ specifications and recommen-dations must be reviewed as applicable.
3.13 Hose Cleanliness—Hose com-ponents vary in cleanliness levels. Caremust be taken to insure that theassemblies selected have an adequatelevel of cleanliness for the application.
3.14 Electrical Conductivity—Certainapplications require that hose be non-conductive to prevent electrical cur-rent flow. Other applications requirethe hose to be sufficiently conductiveto drain off static electricity. Hoseand fittings must be chosen with these needs in mind.
4. Installation—After selection ofproper hose, the following factorsmust be considered by the installer.
4.1 Pre-Installation Inspection—Prior to installation, a careful exami-nation of the hose must be per-formed. All components must bechecked for correct style, size andlength. In addition, the hose must beexamined for cleanliness, I.D.obstructions, blisters, loose cover, orany other visible defects.
4.2 Follow Manufacturers’Assembly Instructions—Hoseassemblies may be fabricated by themanufacturer, an agent for or cus-tomer of the manufacturer, or by theuser. Fabrication of permanentlyattached fittings to hydraulic hoserequires specialized assembly equip-ment. Field-attachable fittings (screwstyle and segment clamp style) canusually be assembled without spe-cialized equipment although manymanufacturers provide equipment toassist in the operation.
SAE J517 hose from one manufactur-er is usually not compatible with SAEJ516 fittings supplied by anothermanufacturer. It is the responsibilityof the fabricator to consult the manu-facturer’s written assembly instruc-tions or the manufacturers directlybefore intermixing hose and fittingsfrom two manufacturers. Similarly,assembly equipment from one man-ufacturer is usually not interchange-able with that of another manufactur-er. It is the responsibility of the fabri-cator to consult the manufacturer’swritten instructions or the manufac-turer directly for proper assemblyequipment. Always follow the manu-facturer’s instructions for properpreparation and fabrication of hoseassemblies.
4.3 Minimum Bend Radius—Installation at less than minimumbend radius may significantly reducehose life. Particular attention must begiven to preclude sharp bending atthe hose/fitting juncture.
4.4 Twist Angle and Orientation—Hose installations must be such thatrelative motion of machine compo-nents produces bending of the hoserather than twisting.
4.5 Securement—In many applica-tions, it may be necessary to restrain,protect, or guide the hose to protectit from damage by unnecessary flex-ing, pressure surges, and contactwith other mechanical components.Care must be taken to insure suchrestraints do not introduce additionalstress or wear points.
4.6 Proper Connection of Ports—Proper physical installation of thehose requires a correctly installedport connection while insuring thatno twist or torque is put into the hose.
4.7 Avoid External Damage—Properinstallation is not complete withoutinsuring that tensile loads, side loads,kinking, flattening, potential abrasion,thread damage, or damage to sealingsurfaces are corrected or eliminated.
4.8 System Check Out—After com-pleting the installation, all air entrap-ment must be eliminated and the sys-tem pressurized to the maximum sys-tem pressure and checked for properfunction and freedom from leaks.
NOTE: Avoid potential hazardousareas while testing.
5. Maintenance—Even with properselection and installation, hose lifemay be significantly reduced withouta continuing maintenance program.Frequency should be determined bythe severity of the application andrisk potential. A maintenance pro-gram should include the following asa minimum.
5.1 Hose Storage—Hose products instorage can be affected adversely bytemperature, humidity, ozone, sunlight,oils, solvents, corrosive liquids andfumes, insects, rodents and radioac-tive materials. Storage areas should berelatively cool and dark and free ofdust, dirt, dampness and mildew.
5.2 Visual Inspection—Any of thefollowing conditions requires replace-ment of the hose:
(a) Leaks at fitting or in hose (leakingfluid is a fire hazard)
(b) Damaged, cut, or abraded cover(any reinforcement exposed)
(c) Kinked, crushed, flattened, ortwisted hose
(d) Hard, stiff, heat cracked orcharred hose
(e) Blistered, soft, degraded, or loosecover
(f) Cracked, damaged, or badly cor-roded fittings
(g) Fitting slippage on hose
5.3 Visual Inspection—The followingitems must be tightened, repaired, orreplaced as required:
(a) Leaking port conditions
(b) Clamps, guards, shields
(c) Remove excessive dirt buildup
(d) System fluid level, fluid type, andany air entrapment
5.4 Functional Test—Operate thesystem at maximum operating pres-sure and check for possible malfunc-tions and freedom from leaks.
NOTE: Avoid potential hazardousareas while testing.
5.5 Replacement Intervals—Specificreplacement intervals must be con-sidered based on previous servicelife, government or industry recom-mendations, or when failures couldresult in unacceptable down time,damage, or injury risk.
357EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
Flow Capacities
For suction hose, follow the same procedure except usesuggested velocity range for pump inlet lines in the righthand column.
Based on Formula
G.P.M. x 0.3208AREA (SQ. IN.) =
VELOCITY (FT./SEC.)
*Suggestions are for oils having a maximum viscosity of315 S.S.U. at +100°F (+38°C) and operating at tempera-tures between +65°F and +155°F (+54°C to +69°C).Under certain conditions, velocities in pressure lines canbe increased up to 25 feet per second. Contact Aeroquipwith specific information on your application.
To convert U.S. gallons into Imperial gallons multiply U.S.gallons by 0.83267. Imperial gallons into U.S. gallons multi-ply Imperial gallons by 1.20095. U.S. gallons to litres multi-ply by 3.785. Litres to U.S. gallons, multiply by 0.2642.
Flow capacities of hose assemblies at suggested flow velocities
The chart below is designed and provided as an aid in thedetermination of the correct hose size.
Example: At 13 U.S. gallons per minute, what is proper hosesize within the suggested velocity range for pressure lines?
Solution: Locate 13 U.S. gallons per minute in the left handcolumn and 10 feet per second in the right hand column(the center of the suggested velocity range for pressurelines). Lay a straightedge across the two points. The insidediameter is shown in the center column nearest thestraight edge.
358 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Hose Dash Size → -04 -05 -06 -08 -10 -12
Hose I.D. (inches) ← .19 .25 .25 .31 .31 .38 .41 .50 .50 .63 .63 .75
.25 10 3.1 3.1
.50 19 6 6 2.7 2.7
1 40 12 12 5.5 5.5 2.4
2 95 24 24 10 10 4.8 3.5
3 185 46 46 17 17 7 5 2.2 2.2
4 78 78 29 29 12 8 3 3 1.2 1.2
5 120 120 44 44 18 12 4.5 4.5 1.6 1.6 .72
8 95 95 39 26 10 10 3.6 3.6 1.4
10 59 40 15 15 5.7 5.7 2
12 80 52 20 20 7.2 7.2 2.6
15 75 30 30 10 10 4.2
18 107 40 40 15 15 6.3
20 49 49 19 19 8
25 72 72 26 26 11
30 34 34 14
35 47 47 19
40 25
50 36
60 50
70
80
90
100
150
200
250
300
400
500
800
1000
Pressure drop in psi (poundsper square inch)/gpm (gal-lons per minute) for 10 feetof hose (smooth bore) with-out fittings.
Fluid specification: Specific gravity = .85; Viscosity = v = 20 centi stokes (C.S.),(20 C.S. = 97 S.S.U.).
Hose pressure drop
-16 -20 -24 -32 -40 -48
.88 1.00 1.13 1.25 1.38 1.50 1.81 2.00 2.38 3.00
.60
1 .55
1.5 .75 .43
2.2 1.2 .67 .38
3 1.5 .70 .55 .35
3.4 2 1.1 .65 .43 .27
5.5 3 1.6 1 .64 .40 .17
7 3.6 2.2 1.3 .80 .52 .22 .14
9.5 5 2.8 1.7 1.1 .70 .27 .18
12 6.5 3.4 2.2 1.4 .90 .38 .24
17 9 5.3 3.3 2 1.3 .54 .35 .15
23 12 7.5 4.4 2.8 1.8 .75 .45 .20
31 17 9.3 6 3.8 2.4 1 .65 .30
38 21 12 7.1 4.6 3 1.2 .76 .34 .11
49 27 15 9 5.9 3.8 1.5 1 .45 .13
33 19 12 7 4.7 1.9 1.3 .55 .18
60 36 22 13 8.5 3.4 2.2 1 .33
36 23 15 6 3.9 1.7 .55
54 33 22 8.5 5.3 2.5 .75
45 29 12 7.5 4 1.1
51 21 14 6.5 2.2
32 20 10 3
18 5
10
U.S
. Gal
lons
per
min
ute
*Pressure drop values listed are typical of many petroleum based hydraulic oils at approximately +100°F (+38°C). Differ ences in fluids, fluid temperature and viscosity can increase or decrease actual pressure drop compared to the values listed.
To Convert
U.S. gallons into Imperial gallons multiply U.S. gallons by 0.83267. Imperial gallons into U.S. gallons multiply Imperial gallons by1.20095. U.S. gallons to litres multiply by 3.785. Litres to U.S. gallons, multiply by 0.2642.
→
→
Flow CapacitiesPressure Drop
359EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SE
Hose Routingand Installation
Under pressure, a hosemay change in length.Always provide some slackin the hose to allow for thisshortening or elongation.
(However, excessive slackin hose lines may causepoor appearance.)
When 90° adapters wereused, this assembly becameneater-looking and easier to
inspect and maintain. It usesless hose, too!
At bends, provide sufficienthose so that it does nothave a bend radius less thanits recommended minimumbend radius. Too tight a bendmay kink the hose and
restrict or stop the fluidflow. In many cases theproper use of adapters andhose fittings can eliminatetight bends or kinks.
In applications where thereis considerable vibration orflexing, allow additional hoselength. The metal hose fit-tings, of course, are not flex-
ible, and proper installationprotects metal parts fromundue stress, and avoidskinks in the hose.
If a hose is installed with atwist in it, operating pres-sures tend to force itstraight. This can loosen the
fitting nut. Twisting cancause reinforcement sepa-ration and the hose couldburst at the point of strain.
When hose lines pass nearan exhaust manifold orother heat source, theyshould be insulated by aheat resistant boot,firesleeve or a metal baffle.In any application, bracketsand clamps keep hoses inplace and reduce abrasion.
For installations whereabrasion to hose cover can-not be prevented with theuse of clamps or brackets,a steel protective coil orabrasion resistant sleeveshould be placed over thehose.
360 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Analyzing Failures
Everyone in maintenanceencounters hose failures.Normally, there is no prob-lem. The hose is replacedand the equipment goesback in operation.Occasionally the failurescome too frequently – thesame equipment with thesame problems keep pop-ping up. At this point thetask is to determine andcorrect the cause of theserepeated failures.
Improper application
Beginning with the mostobvious, the most commoncause of hose failures –Improper Application –compare the hose specifi-cations with the require-ments of the application.
Pay particular attention tothe following areas:
1. The maximum operatingpressure of the hose.
2. The recommended tem-perature range of thehose.
3. Whether the hose israted for vacuum service.
4. The fluid compatibility ofthe hose.
Check all of these areasagainst the requirements ofthe application. If they don’tmatch up, you need toselect another hose. It’s agood idea at this point tocall on your local hose dis-tributor for assistance inselecting the proper hose.Eaton’s distributors, forexample, are well equippedto perform this service foryou. Distributor personnelattend special trainingcourses in hydraulics andhose application conductedby the company. Or, if yourproblem is particularly diffi-cult, the distributor can callon the services of Eaton’s
Field Engineering Staff. Thecompany will send in ahose and hydraulic special-ist to study the problem andcome up with a solution.
Improper assembly andinstallation
The second major cause ofpremature hose failure isimproper assembly andinstallation procedures. Thiscan involve anything fromusing the wrong fitting on ahose, to poor routing of the hose.
Eaton provides excellenttraining material that youcan use to combat thisproblem. A little time spentin training your mainte-nance people could pay big dividends in reduceddowntime.
You can make use of thematerial available fromEaton to improve your hoseassembly and installationtechniques.
This material is availablefree from Eaton Corporation14615 Lone Oak Road,Eden Prairie, MN 55344USA, 952/937-9800.
External damage
External damage can rangefrom abrasion and corro-sion, to hose that iscrushed by a lift truck.These are problems thatcan normally be solved sim-ply once the cause is identi-fied. The hose can be re-routed or clamped, or a firesleeve or abrasion guardcan be used.
In the case of corrosion,the answer may be as sim-ple as changing to a hosewith a more corrosionresistant cover or re-routingthe hose to avoid the corro-sive element.
Faulty equipment
Too frequent or prematurehose failure can be thesymptom of a malfunctionin your equipment. This is afactor that should be con-sidered since prompt cor-rective action can some-times avoid serious andcostly equipment break-down. Reprints of an articleon “TroubleshootingHydraulic Systems,” whichtells you how to spot prob-lems in a hydraulic systemare available from Eaton.
Faulty hose
Occasionally a failure prob-lem will lie in the hoseitself. The most likely causeof a faulty rubber hose isold age. Check the lay lineon the hose to determinethe date of manufacture.(2Q99 means second quar-ter 1999.) The hose mayhave exceeded its recom-mended shelf life. If yoususpect that the problemlies in the manufacture ofthe hose (and don’t jump tothis conclusion until youhave exhausted the otherpossibilities) contact yourdistributor. Given effectivequality control methods,the odds of a faulty batchof hose being released forsale are extremely small.So make sure that youhaven’t overlooked someother problem area.
Analyzing failures
A physical examination ofthe failed hose can oftenoffer a clue to the cause ofthe failure. Following are 22symptoms to look for alongwith the conditions thatcould cause them:
1. Symptom: The hosetube is very hard and hascracked.
Cause: Heat has a tenden-cy to leach the plasticizersout of the tube. This is amaterial that gives the hoseits flexibility or plasticity.
Aerated oil causes oxida-tion to occur in the tube.This reaction of oxygen ona rubber product will causeit to harden. Any combina-tion of oxygen and heat willgreatly accelerate the hard-ening of the hose tube.Cavitation occurring insidethe tube would have thesame effect.
2. Symptom: The hose iscracked both externally andinternally but the elas-tomeric materials are softand flexible at room tem-perature.
Cause: The probable rea-son is intense cold ambientconditions while the hosewas flexed. Most standardhoses are rated to –40°F(–40°C). Some AQP hosesare rated at –55°F (–49°C).Military specified hoses aregenerally rated to –65°F(–54°C). PTFE hose is ratedto –100°F (–73°C). SomeEverflex Polyon thermoplas-tic hoses are rated at –65°F(–54°C).
361EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
3. Symptom: The hosehas burst and examinationof the wire reinforcementafter stripping back thecover reveals random bro-ken wires the entire lengthof the hose.
Cause: This would indicatea high frequency pressureimpulse condition. SAE impulse test requirementsfor a double wire braid rein-forcement are 200,000cycles at 133% of recom-mended working pressure.The SAE impulse testrequirements for a four spi-ral wrapped reinforcement(100R12) are 500,000cycles at 133% maximumoperating and at +250°F(121°C). If the extrapolatedimpulses in a systemamount to over a million ina relatively short time a spi-ral reinforced hose wouldbe the better choice.
4. Symptom: The hosehas burst, but there is noindication of multiple bro-ken wires the entire lengthof the hose. The hose may
have burst in more thanone place.
Cause: This would indicatethat the pressure hasexceeded the minimumburst strength of the hose.Either a stronger hose isneeded or the hydraulic cir-cuit has a malfunctionwhich is causing unusuallyhigh pressure conditions.
5. Symptom: Hose hasburst. An exam-ination indi-cates the the wire braid isrusted and the cover hasbeen cut, abraded or deteri-orated badly.
Cause: The primary func-tion of the cover is to pro-tect the reinforcement.Elements that may destroyor remove the hose coversare:
1. Abrasion
2. Cutting
3. Battery Acid
4. Steam Cleaners
5. Chemical CleaningSolutions
6. Muriatic Acid (for cementclean-up)
7. Salt Water
8. Heat
9. Extreme Cold
Once the cover protectionis gone the wire reinforce-ment is susceptible toattack from moisture orother corrosive matter.
6. Symptom: Hose hasburst on the outside bendand appears to be ellipticalin the bent section. In thecase of a pump supply line,the pump is noisy and veryhot. The exhaust line on thepump is hard and brittle.
Cause: Violation of the min-imum bend radius is mostlikely the problem in bothcases. Check the minimumbend radius and make surethat the application is withinspecifications. In the caseof the pump supply line par-tial collapse of the hose iscausing the pump to cavi-tate creating both noise andheat. This is a most serioussituation and will result incatastrophic pump failure ifnot corrected.
7. Symptom: Hoseappears to be flattened outin one or two areas andappears to be kinked. It hasburst in this area and alsoappears to be twisted.
Cause: Torquing of ahydraulic control hose willtear loose the reinforce-ment layers and allow thehose to burst through theenlarged gaps between thebraided plaits of wirestrands. Use swivel fittingsor joints to be sure there isno twisting force on ahydraulic hose.
8. Symptom: Hose type hasbroken loose from the rein-forcement and piled up atthe end of the hose. In somecases it may protrude fromthe end of the hose fitting.
Cause: The probable causeis high vacuum or thewrong hose for vacuumservice. No vacuum is rec-ommended for double wirebraid, 4 and 6 spiral wirehose unless some sort ofinternal coil support isused. Even though a hoseis rated for vacuum service,if it is kinked, flattened outor bent too sharply thistype of failure may occur.
9. Symptom: Hose hasburst about six to eight inch-es away from the end fit-ting. The wire braid is rust-ed. There are no cuts orabrasions of the outer cover.
Cause: Improper assemblyof the hose end fittingallowing moisture to enteraround the edge of the fit-ting socket. The moisturewill wick through the rein-forcement. The heat gener-ated by the system willdrive it out around the fit-ting area but six to eightinches away it will beentrapped between theinner line and outer covercausing corrosion of thewire reinforcement.
10. Symptom:There are blis-ters in the cover of the hose.If one pricks the blisters, oilwill be found in them.
Cause: A minute pin hole inthe hose tube is allowing thehigh pressure oil to seep be -tween it and the cover.Eventually it will form a blis-ter wherever the cover adhe-sion is weakest. In the caseof a screw together reusablefitting insufficient lubricationof the hose and fitting cancause this condition be causethe dry tube will adhere tothe rotat ing nipple and tearenough to allow seepage.Faulty hose can also causethis condition.11.Symptom: Blistering ofthe hose cover where agaseous fluid is being used.
Cause:The high pressuregas is effusing through thehose tube, gathering underthe cover and eventuallyforming a blister whereverthe adhesion is weakest.Specially constructed hosesare available for high pres-sure gaseous applications.Your supplier can adviseyou on the proper hose touse in these cases.12. Symptom: Fitting blewoff of the end of the hose.
Cause: It may be that thewrong fitting has been puton the hose. Recheck man-ufacturer’s specificationsand part numbers.In the case of a crimped fit-ting the wrong machinesetting may have beenused resulting in over orundercrimping. The socketof a screw together fittingfor multiple wire braidedhose may be worn beyondits tolerance. The swagingdies in a swaged hoseassembly may be wornbeyond the manufacturer’stolerances.The fitting may have beenapplied improperly to thehose. Check manufacturer’sinstructions. The hose mayhave been installed withoutleaving enough slack tocompensate for the possi-ble 4% shortening thatmay occur when the hoseis pressurized. This willimpose a great force on thefitting. The hose itself maybe out of tolerance.
362 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
13. Symptom: The tube ofthe hose is badly deteriorat-ed with evidences of ex -treme swelling. In somecases the hose tube maybe partially “washed out.”
Cause: Indications are thatthe hose tube is not com-patible with the agent beingcarried. Even though theagent is normally compati-ble, the addition of heat canbe the catalyst that cancause inner liner deteriora-tion. Con sult your hosesupplier for a compatibilitylist or present him with asample of the fluid beingconducted by the hose foranalysis. Make sure thatthe operating temperaturesboth internal and externaldo not exceed recommendations.
14. Symptom: Hose hasburst. The hose cover isbadly deteriorated and thesurface of the rubber iscrazed.
Cause: This could be simplyold age. The crazed appear-ance is the effect of weather-ing and ozone over a periodof time. Try to determine theage of the hose. Some man-ufacturers print or embossthe cure date on the outsideof the hose. As an example,Aeroquip hose would show“4Q01” which would meanthat the hose was manufac-tured during the fourth quar-ter (October, November orDecember) of 2001.
15. Symptom: Hose isleaking at the fittingbecause of a crack in themetal tube adjacent to thebraze on a split flange head.
Cause: Because the crackis adjacent to the braze andnot in the braze this is astress failure brought on bya hose that is trying toshorten under pressure andhas insufficient slack in it todo so.
We have cured dozens ofthese problems by lengthen-ing the hose assembly orchanging the routing to relievethe forces on the fitting.
16. Symptom: A spiral rein-forced hose has burst andliterally split open with thewire exploded out and badlyentangled.
Cause: The hose is tooshort to accommodate thechange in length occurringwhile it is pressured.
17.Symptom: Hose is badlyflattened out in the burstarea. The tube is very harddown stream of the burstbut appears normal upstream of the burst.
Cause: The hose has beenkinked either by bending ittoo sharply or by squashingit in some way so that amajor restriction was creat-ed. As the velocity of thefluid increases through therestriction the pressuredecreases to the vaporiza-tion point of the fluid beingconveyed. This is commonlycalled cavitation, and caus-es heat and rapid oxidationto take place which hardensthe tube of the hose downstream of the restriction.
18.Symptom: Hose has notburst but it is leaking pro-fusely. A bisection of thehose reveals that the tubehas been gouged throughto the wire braid for a dis-tance of approximately twoinches.
Cause: This failure wouldindicate that erosion of thehose tube has taken place. Ahigh velocity needle like fluidstream being emitted froman orifice and impinging at asingle point on the hose tubewill hydraulically remove asection of it. Be sure that thehose is not bent close to aport that is orificed.
In some cases where highvelocities are encounteredparticles in the fluid cancause considerable erosionin bent sections of the hoseassembly.
19. Symptom: The hose fit-ting has been pulled out ofthe hose. The hose has beenconsiderably stretched out inlength. This may not be ahigh pressure application.
Cause: Insufficient supportof the hose. It is very neces-sary to support very longlengths of hose, especially ifthey are vertical. The weightof the hose along with theweight of the fluid inside thehose in these cases is beingimposed on the hose fitting.This force can be transmittedto a wire rope or chain byclamping the hose to it muchlike the utilities support bun-dles of wire from pole topole. Be sure to leave suffi-cient slack in the hosebetween clamps to make upfor the possible 4% shorten-ing that could take placewhen the hose is pressur-ized.
20. Symptom: The hose hasnot burst but it is leaking pro-fusely. An examination of thebisected hose reveals thatthe tube has burst inwardly.
Cause: This type of failure iscommonly re ferred to ashose tube blow down. It isusually associated with verylow viscosity fluids such asair, nitrogen, freon and othergases. What happens is thatunder high pressure condi-tions the gases will effuseinto the pores of the hosetube charging them up likeminiature accumulators. Ifthe pressure is very sudden-ly reduced to zero theentrapped gases literallyexplode out of the tube oftentearing holes in it. In somehose constructions a second
hose tube made from aplastic such as nylon, isinserted into the hose.A small leak will allow thegaseous fluid to seepbetween the two inner lin-ers and when the pressureis reduced to zero the inner-most liner will collapsebecause of the entrappedpressure around its outerdiameter.21. Symptom: PTFE hoseassembly has collapsed inter-nally in one or more places.
Cause: One of the mostcommon causes for this isimproper handling of thePTFE as sembly. PTFE is athermoplastic material whichis not rubber-like. When bentsharply it simply collapses.This type of collapse is local-ized in one area and is radial.When the PTFE tube is fold-ed longitudinally in one ormore places this could bethe result of heat (which soft-ens the hose tube) alongwith vacuum conditionsinside of it. Because of theadditional tension of the wirebraid reinforcement inherentwith this type of hose, thereis always a radial tension onthe tube trying to push it in.Rapid cycling from a very hotagent in the hose to a verycold agent in the hose canproduce the same type offailure. Eaton offers an inter-nal support coil that will elim-inate this problem. 22. Symptom: A PTFE hoseassembly has developed apin hole leak or several pinhole leaks.
Cause:This situation occurswhen a pet roleum base fluid,with a low viscosity, is flow-ing at a high velocity. Thiscondition can generate highvoltage due to static electric -ity. The high voltage is seek-ing a ground connection andthe only ground connectionavailable is the braided stain-less steel reinforcement. Thiscauses an electric arc, whichpenetrates through the PTFEtube as it travels to the rein-forcement. Specially con-structed PTFE tubes areavailable that have enoughcarbon black in them so as tobe conductive. They will“drain off” the static electrici-ty and preclude this problem.
363EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
Measuring Tools—Order part number FT1341 for TheIndentification Tool Kit. A seat angle gauge, thread pitchgauge and an I.D./O.D. caliper are necessary to make accurate measurements of commonly used connectors.Eaton offers a unique new caliper than offers the capabili-ties of both a caliper and a seat angle gauge in one unit.
How to Measure Threads
Use a thread pitch gauge to determine the number of threadsper inch or the distance between threads in metric connec-tions. Place the gauge on the threads until the fit is snug.Match the measurement to the charts.
How to IdentifyFluid Connectors
Measure the thread diame-ter with an I.D./O.D. caliperas shown.
Match the measurements tothe charts.
I.D./O.D. Angle Gauge Caliper
Thread Pitch Gauge
How to Measure SealingSurface Angles
Female connections are usu-ally measured by insertingthe gauge into the connec-tion and placing it on thesealing surface. If the cen-terlines of the connectionand gauge are parallel, thecorrect angle has beendetermined.
Male flare type connectorsare usually measured byplacing the gauge on thesealing surface. If the cen-terlines of the connectionand gauge are parallel, thecorrect angle has beendetermined.
364 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
EThrough
Hole
EThrough
Hole
SAE 37°
ORS
Thread SizeChart
The following chart is intended as a quick reference guide for threadsize by dash size.
Dash N.P.S.M. SAE 45° SAE 37° (J.I.C.) SAE O-Ring P.T.T. 30° SAE Invert.size N.P.T.F. Approx. Dia. Auto. Refrig. Hydraulic Boss Automotive Flare ORS
–02 1/8–27 1/8–27 5/16–24 5/16–24 5/16–24 5/16–24–03 3/8–24 3/8–24 3/8–24 3/8–24–04 1/4–18 1/4–18 7/16–20 7/16–20 7/16–20 7/16–24 9/16–18–05 1/2–20 1/2–20 1/2–20 1/2–20–06 3/8–18 3/8–18 5/8–18 9/16–18 9/16–18 5/8–18 11/16–16–07 11/16–24 11/16–18–08 1/2–14 1/2–14 3/4–16 3/4–16 3/4–16 3/4–18 13/16–16–10 7/8–14 7/8–14 7/8–14 7/8–18 1–14–12 3/4–14 3/4–14 11/16–14 11/16–12 11/16–12 11/16–16 13/16–12–14 13/16–12 13/16–12–16 1–111/2 1–111/2 15/16–12 15/16–12 15/16–14 17/16–12–20 11/4–111/2 11/4–111/2 15/8–12 15/8–12 15/8–14 111/16–12–24 11/2–111/2 11/2–111/2 17/8–12 17/8–12 17/8–14 2–12–32 2–111/2 2–111/2 21/2–12 21/2–12 21/2–12–40 21/2–8 21/2–8 3–12 3–12–48 3–8 3–8 31/2–12 31/2–12
Through hole dimensions
All dimensions are nominal.In jump size bodies, the min-imum through hole dimen-sions will correspond to thesmallest dash size.
Dash E through holeSize SAE 37° ORS
mm in mm in–03 3,0 0.12– 04 4,3 0.17 4,3 0.17–05 5,8 0.23–06 7,6 0.30 6,6 0.26–08 9,9 0.39 9,7 0.38–10 12,2 0.48 12,2 0.48–12 15,5 0.61 15,5 0.61–16 21,3 0.84 20,6 0.81–20 25,8 1.08 26,7 1.05–24 33,3 1.31 33,3 1.31–32 45,2 1.78
365EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
NominalInch Dash Thread Male Thread Female threadSize size size O.D. inch I.D. inch
fraction decimal fraction decimal1/8 02 1/8-27 13/32 .41 3/8 .381/4 04 1/4-18 17/32 .54 1/2 .493/8 06 3/8-18 11/16 .68 5/8 .631/2 08 1/2-14 27/32 .84 25/32 .773/4 12 3/4-14 11/16 1.05 1 .981 16 1-111/2 15/16 1.32 11/4 1.2411/4 20 11/4-111/2 121/32 1.66 119/32 .5811/2 24 11/2-111/2 129/32 1.90 113/16 1.822 32 2-111/2 23/8 2.38 25/16 2.30
AmericanConnections
How to MeasureNon-ThreadedConnections
Tapered
ThreadO.D.
ThreadI.D.
Tapered
Male Half Female Half This connection is stillwidely used in fluid powersystems, even though it isnot recommended by theNational Fluid PowerAssociation (NFPA) for use
in hydraulic applications.The thread is tapered andthe seal takes place bydeformation of the threads.
Measure thread diameterand subtract 1/4-inch to findthe nominal pipe size.
NPSM(National PipeStraight Mechanical)
NominalInch Dash Thread Male Thread Female threadSize size size O.D. inch I.D. inch
fraction decimal fraction decimal1/8 02 1/8-27 13/32 .41 3/8 .381/4 04 1/4-18 17/32 .54 1/2 .493/8 06 3/8-18 11/16 .68 5/8 .631/2 08 1/2-14 27/32 .84 25/32 .773/4 12 3/4-14 11/16 1.05 1 .981 16 1-111/2 15/16 1.32 11/4 1.2411/4 20 11/4-111/2 121/32 1.66 119/32 .5811/2 24 11/2-111/2 129/32 1.90 113/16 1.822 32 2-111/2 23/8 2.38 25/16 2.30
This connection is some-times used in fluid powersystems. The female halfhas a straight thread and aninverted 30° seat. The malehalf of the connection has astraight thread and a 30°internal chamfer. The seal
takes place by compressionof the 30° seat on the cham-fer. The threads hold theconnection mechanically.
NOTE: A properly chamferedNPTF male will also sealwith the NPSM female.
NPTF(National PipeTapered Fuel)
NPTF Threads
Four Bolt Flange—Firstmeasure the port holediameter using the caliper.Next, measure the longestbolt hole spacing from cen-ter-to-center or measurethe flange head diameter.
Staplok—Measure themale diameter with theO.D. portion of the caliper.Measure the female half byinserting the I.D. portion of the caliper into thethrough hole.
Dash Numbers
Most fluid piping systemsizes in the United Statesare measured by dashnumbers. These are univer-sally used abbreviations forthe size of the componentexpressed as the numera-tor of the fraction with the
denominator always being16. For example, a –04 portis 4/16 or 1/4-inch. Dash num-bers are usually nominal (inname only) and are abbrevi-ations that make orderingof components easier.
366 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction decimal fraction decimal1/8 02 5/16-24 5/16 .31 9/32 .273/16 03 3/8-24 3/8 .38 11/32 .341/4 04 7/16-20 7/16 .44 13/32 .395/16 05 1/2-20 1/2 .50 15/32 .453/8 06 9/16-18 9/16 .56 17/32 .511/2 08 3/4-16 3/4 .75 3/4 .695/8 10 7/8-14 7/8 .88 13/16 .813/4 12 11/16-12 11/16 1.06 1 .987/8 14 13/16-12 13/16 1.19 11/8 1.131 16 15/16-12 15/16 1.31 11/4 1.2311/4 20 15/8-12 15/8 1.63 19/16 1.5411/2 24 17/8-12 17/8 1.88 113/16 1.792 32 21/2-12 21/2 2.50 27/16 2.42
AmericanConnections
This port connection is recom-mended by the NFPA for opti-mum leakage control in mediumand high pressure hydraulic sys-tems. The male connector has astraight thread and an O-Ring.The female port has a straight
thread, a machined surface (min-imum spotface) and a chamferto accept the O-Ring. The seal takes place bycompressing the O-Ring into thechamfer. The threads hold theconnection mechanically.
ORS SAE J1453 O-Ring Face Seal
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction decimal fraction decimal1/4 04 9/16-18 9/16 .56 17/32 .513/8 06 11/16-16 11/16 .69 5/8 .631/2 08 13/16-16 13/16 .82 3/4 .755/8 10 1-14 1 1.00 15/16 .933/4 12 13/16-12 13/16 1.19 11/8 1.111 16 17/16-12 17/16 1.44 13/8 1.3611/4 20 111/16-12 111/16 1.69 15/8 1.6111/2 24 2-12 2 2.00 115/16 1.92
This connection offers the verybest leakage control availabletoday. The male connector hasa straight thread and an O-Ring in the face. The femalehas a straight thread and amachined flat face. The seal
takes place by compressingthe O-Ring onto the flat faceof the female, similar to thesplit flange type fitting. Thethreads hold the connectionmechanically.
SAE J514 37°Hydraulic
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction decimal fraction decimal1/8 02 5/16-24 5/16 .31 9/32 .273/16 03 3/8-24 3/8 .38 11/32 .341/4 04 7/16-20 7/16 .44 13/32 .395/16 05 1/2-20 1/2 .50 15/32 .453/8 06 9/16-18 9/16 .56 17/32 .511/2 08 3/4-16 3/4 .75 3/4 .695/8 10 7/8-14 7/8 .88 13/16 .813/4 12 11/16-12 11/16 1.06 1 .987/8 14 13/16-12 13/16 1.19 11/8 1.131 16 15/16-12 15/16 1.31 11/4 1.2311/4 20 15/8-12 15/8 1.63 19/16 1.5411/2 24 17/8-12 17/8 1.88 113/16 1.792 32 21/2-12 21/2 2.50 27/16 2.42
This connection is very com-mon in fluid power systems.Both the male and femalehalves of the connections have37° seats. The seal takes placeby establishing a line contactbetween the male flare and thefemale cone seat.
The threads hold the connec-tion mechanically. CAUTION: Inthe –02, –03, –04, –05, –08 and–10 sizes, the threads of theSAE 45° flare and the SAE 37°flare are the same. However,the sealing surface angles arenot the same.
SAE J512Inverted
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction decimal fraction decimal1/8 02 5/16-24 5/16 .32 9/32 .283/16 03 3/8-24 3/8 .38 11/32 .341/4 04 7/16-24 7/16 .44 13/32 .405/16 05 1/2-20 1/2 .50 15/32 .453/8 06 5/8-18 5/8 .63 9/16 .577/16 07 11/16-18 11/16 .69 5/8 .631/2 08 3/4-18 3/4 .75 23/32 .705/8 10 7/8-18 7/8 .88 13/16 .823/4 12 11/16-16 11/16 1.06 1 1.00
This connection is frequentlyused in automotive systems.The male connector can eitherbe a 45° flare in the tube fittingform or a 42° seat in themachined adapter form. The
female has a straight threadwith a 42° inverted flare. Theseal takes place on the flaredsurfaces. The threads hold theconnection mechanically.
SAE J1926 StraightThread O-Ring Boss(ORB)
367EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
SAE J512 45°
Staplok (SAE J1467)
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction decimal fraction decimal1/8 02 5/16-24 5/16 0.31 9/32 0.273/16 03 3/8-24 3/8 0.38 11/32 0.341/4 04 7/16-20 7/16 0.44 13/32 0.395/16 05 1/2-20 1/2 0.50 15/32 0.453/8 06 5/8-18 5/8 0.63 9/16 0.571/2 08 3/4-16 3/4 0.75 11/16 0.695/8 10 7/8-14 7/8 0.88 13/16 0.813/4 12 11/16-14 11/16 1.06 1 0.997/8 14 11/4-12 11/4 1.25 15/32 1.161 16 13/8-12 13/8 1.38 19/32 1.29
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. inch O.D. inch
fraction† decimal fraction decimal1/4 04 9/32 .586 19/32 .5973/8 06 25/32 .783 51/64 .7941/2 08 15/16 .940 61/64 .9513/4 12 19/64 1.137 19/64 1.1481 16 117/32 1.529 135/64 1.54011/4 20 113/16 1.806 113/16 1.81711/2 24 25/32 2.163 211/64 2.1742 32 233/64 2.517 217/32 2.528
This connection is commonlyused in refrigeration, automotiveand truck piping systems. Theconnector is frequently made ofbrass. Both the male and femaleconnectors have 45° seats. Theseal takes place between themale flare the female cone seat.
The threads hold the connectionmechanically. CAUTION: In the–02, –03, –04, –05, –08 and –10sizes, the threads of the SAE45° flare and the SAE 37° flareare the same. However, thesealing surface angles are notthe same.
This is a radial O-Ring sealconnection developed inGermany and commonlyused for hydraulic applicationin underground mines. Themale contains an exterior O-Ring and backup ring, plus agroove to accept the “sta-ple”. The female has asmooth bore with two holes
for the stable. A “U” shapedretaining clip or staple isinserted through the twoholes, passing through thegroove in the male to lockthe connection together. Theseal takes place by contactbetween the O-Ring in themale and the smooth bore ofthe female.
†Measure to the closest 1/64-inch.
SAE J518 4-Bolt Flange*
This connection is commonlyused in fluid power systems.There are two pressure rat-ings. Code 61 is referred to asthe “standard” series andCode 62 is the “6000 psi”series. The design concept forboth series is the same, butthe bolt hole spacing andflanged head diameters arelarger for the higher pressure,Code 62 connection.The female (port) is anunthreaded hole with four boltholes in a rectangular patternaround the port. The male con-
sists of a flanged head,grooved for an O-Ring, andeither a captive flange or splitflange halves with bolt holes tomatch the port. The seal takesplace on the O-Ring, which iscompressed between theflanged head and the flat sur-face surrounding the port. Thethreaded bolts hold the con-nection together.
*SAE J518, JIS B 8363,ISO/DIS 6162 and DIN 20066are interchangeable, exceptfor bolt sizes.
How to Measure
Four Bolt Flange—Firstmeasure the port hole diam-eter using the caliper. Next,measure the longest bolthole spacing from center-to-center (Dimension “A”) ormeasure the flanged headdiameter.
PortHole
Inch I.D.Size inch Bolt Bolt Hole Flanged (Dash fract. Dimension Spacing “A” Head Dia. “K”size) (deci.) inch inch (decimal) inch (dec)
Cd. 61 Cd. 62 Cd. 61 Cd.62 Cd. 61 Cd. 621/2 1/2 5/16-18x11/4 5/16-18x11/4 11/2 119/32 13/16 11/4(08) (.50) (1.50) (1.59) (1.19) (1.25)3/4 3/4 3/8-16x11/4 3/8-16x11/2 17/8 2 11/2 15/8(12) (.75) (1.88) (2.00) (1.50) (1.63)1 1 3/8-16x11/4 7/16-14x13/4 21/16 21/4 13/4 17/8(16) (1.00) (2.06) (2.25) (1.75) (1.88)11/4 11/4 7/16-14x11/2 1/2-13x13/4 25/16 25/8 2 21/8(20) (1.25) (2.31) (2.63) (2.00) (2.13)11/2 11/2 1/2-13x11/2 5/8-11x21/4 23/4 31/8 23/8 21/2(24) (1.50) (2.75) (3.12) (2.38) (2.50)2 2 1/2-13x11/2 3/4-10x23/4 31/16 313/16 213/16 31/8(32) (2.00) (3.06) (3.81) (2.81) (3.12)
368 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Port Bolt Bolt Hole Size Hole Dimensions Spacing “A”
ISO 6162-1 ISO 6162-2 ISO 6162-1 ISO 6162-2Bar (Cd.61) Bar (Cd. 62) Bar (Cd. 61) Bar (Cd. 62)
mm in [dash] mm [in] mm [in] mm [in] mm [in] mm [in]13 12,7 M8 x 1.25 x 30 M8 x 1.25 x 30(1/2) [.50] [5/16–18 x 11/4] [5/16–18 x 11/4] 38.1 40.5[08] [1.50] [1.57]19 19,1 M10 x 1.5 x 35 M10 x 1.5 x 40(3/4) [.75] [3/8–16 x 11/4] [3/8–16 x 11/2] 47.6 50.8[12] [1.88] [2.00]25 25,4 M10 x 1.5 x 35 M12 x 1.75 x 45(1) [1.00] [3/8–16 x 11/4] [7/16–14 x 13/4] 52.4 57.2[16] [2.06] [2.25]32 31,8 M10 x 1.5 x 40 M14 x 2 x 50(11/4) [1.25] [7/16–14 x 11/2] [1/2–13 x 13/4] 58.7 66.7[20] [2.31] [2.63]38 38,1 M12 x 1.75 x 40 M16 x 2 x 55(11/2) [1.50] [1/2–13 x 11/2] [5/8–11 x 21/4] 69.9 79.4[24] [2.75] [3.13]51 50,8 M12 x 1.75 x 40 M20 x 2.5 x 70(2) [2.00] [1/2–13 x 11/2] [3/4–10 x 23/4] 77.8 96.8[32] [3.06] [3.81]
ISO connections
This connection is commonlyused in fluid power systems.There are two pressure ratings.PN 35/350 bar (Code 61) is the“standard” series and PN 415bar (Code 62) is the high pres-sure series. The design conceptfor both series is the same, butthe bolt hole spacing andflanged head diameters arelarger for the higher pressure,PN 415 bar connection. Bothmetric and inches bolts areused. The port will have an “M”stamped on it if metric boltsare required.
The female (port) is anunthreaded hole with four boltholes in a rectangular patternaround the port. The male con-sists of a flanged head,grooved for an O-Ring, andeither a captive flange or splitflange halves with bolt holes tomatch the port. The seal takesplace on the O-Ring, which iscompressed between theflanged head and the flat sur-face surrounding the port. Thethreaded bolts hold the connec-tion together.
*ISO/DIS 6162, DIN 20066, JISB 8363 and SAE J518 areinterchangeable, except forbolt sizes.
DIN 7631 Series
Inch Flanged Head Size Dia. “K”
ISO 6162-1 ISO 6162-2Bar (Cd.61) Bar (Cd. 62)mm in mm in
1/2 30.18 1.19 31.75 1.253/4 38.10 1.50 41.28 1.631 44.45 1.75 47.63 1.8811/4 50.80 2.00 53.98 2.1311/2 60.33 2.38 63.50 2.502 71.42 2.81 79.38 3.13
This connection is frequentlyused in hydraulic systems. Themale has a straight metricthread and a 60° (includedangle) recessed cone. Thefemale has a straight threadand a tapered nose/Globeseal
seat. The seal takes place bycontact between the cone ofthe male and the nose of thetapered nose/Globeseal flare-less swivel. The threads holdthe connection mechanically.
MetricUse With Thread Male Thread Female ThreadPipe/Tube O.D. Size O.D. I.D.
mm in mm in mm in6 0.24 M12 x 1.5 12 0.47 10,5 0.418 0.32 M14 x 1.5 14 0.55 12,5 0.4910 0.39 M16 x 1.5 16 0.63 14,5 0.5712 0.47 M18 x 1.5 18 0.71 16,5 0.6515 0.59 M22 x 1.5 22 0.87 20,5 0.8118 0.71 M26 x 1.5 26 1.02 24,5 0.9622 0.87 M30 x 1.5 30 1.18 28,5 1.1228 1.10 M38 x 1.5 38 1.50 36,5 1.4435 1.38 M45 x 1.5 45 1.77 43,5 1.7142 1.65 M52 x 1.5 52 2.04 50,5 1.99
GermanConnections
ISO/DIS 6162 4-Bolt Flange*
369EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
DIN 3902 Series
This connection style consistsof a common male and threedifferent female halves.
The male has a straight metricthread, a 24° included angleand a recessed counterborethat matches the tube O.D.used with it. The female may
be a tube, nut and ferrule, atapered nose/Globeseal flare-less swivel or a taperednose/Globeseal flareless swiv-el with an O-Ring in the nose(DKO type).
*I.Rh. is a light duty system.†s.Rh. is a heavy duty system.
Tube O.D. Tube O.D. Metric“R” Dim. “R” Dim. Thread Male Thread Female ThreadI.Rh.* s.Rh.† Size O.D. I.D.
mm in. mm in mm in mm in6 0.24 M12 x 1.5 12 0.47 10.5 0.418 0.32 6 0.24 M14 x 1.5 14 0.55 12.5 0.4910 0.39 8 0.32 M16 x 1.5 16 0.63 14.5 0.5712 0.47 10 0.39 M18 x 1.5 18 0.71 16.5 0.65
12 0.47 M20 x 1.5 20 0.78 18.5 0.7315 0.59 14 0.55 M22 x 1.5 22 0.87 20.5 0.81
16 0.63 M24 x 1.5 24 0.94 22.5 0.8918 0.71 M26 x 1.5 26 1.02 24.5 0.9622 0.87 20 0.78 M30 x 2.0 30 1.18 28 1.1128 1.10 25 0.98 M36 x 2.0 36 1.41 34 1.34
30 1.18 M42 x 2.0 42 1.65 40 1.5735 1.38 M45 x 2.0 45 1.77 43 1.7042 1.65 38 1.50 M52 x 2.0 52 2.04 50 1.97
DIN 20066 4-BoltFlange*
This connection is commonlyused in fluid power systems.There are two pressure rat-ings. Form R (Code 61) isreferred to as the “standardduty” series and Form S(Code 62) is the “heavy duty”series. The design concept forboth series is the same, butthe bolt hole spacing andflanged head diameters arelarger for the higher pressure,Form S connection. Both met-ric and inch bolts are used.
The female (port) is anunthreaded hole with four boltholes in a rectangular patternaround the port. The male con-sists of a flanged head,grooved for an O-Ring, andeither a captive flange or splitflange halves with bolt holesto match the port. The sealtakes place on the O-Ring,which is compressed betweenthe flanged head and the flatsurface surrounding the port.The threaded bolts hold theconnection together.
*DIN 20066, IS/DIS 6166, JISB 8363 and SAE J518 areinterchangeable, except forbolt sizes.
Sizemm(inch) Port[dash] Hole Bolt Dimensions Bolt Hole Spacing
Form R. Form S Form R Form S(Cd. 61) (Cd. 62) (Cd. 61) (Cd. 62)
mm (in) mm (in) mm (in)
12 12.7 M8 x 1.25 x 30 M8 x 1.25 x 30(1/2) (.50) 5/16-18 x 11/4 5/16-18 x 11/4 38.10 40.49[08] (1.50) (1.57)20 19.1 M10 x 1.5 x 30 M10 x 1.5 x 40(3/4) (.75) 3/8-16 x 11/4 3/8-16 x 11/2 47.63 50.80[12] (1.88) (2.00)25 25.4 M10 x 1.5 x 35 M12 x 1.75 x 45(1) (1.00) 3/8-16 x 11/4 7/16-14 x 13/4 52.37 57.15[16] (2.06) (2.25)32 31.7 M10 x 1.75 x 40 M14 x 2 x 45(11/4) (1.25) 7/16-14 x 11/2 1/2-13 x 13/4 58.72 66.68[20] (2.31) 2.63)40 38.0 M12 x 1.75 x 40 M16 x 2 x 55(11/2) (1.50) 1/2-13 x 11/2 5/8-11 x 21/4 69.85 79.38[24] (2.75) (3.13)50 50.8 M12 x 1.75 x 40 M20 x 2.5 x 70(2) (2.00) 1/2-13 x 11/2 3/4-10 x 23/4 77.77 96.82[32] (3.06) (3.81)
Inch Flanged Head Size Dia. “K”
FORM R FORM S(Cd. 61) (Cd. 62)
mm in mm in1/2 30.18 1.19 31.75 1.253/4 38.10 1.50 41.28 1.631 44.45 1.75 47.63 1.8811/4 50.80 2.00 53.98 2.1311/2 60.33 2.38 63.50 2.502 71.42 2.81 79.38 3.13
370 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
DIN 3852 Metric ThreadsDIN 3852 Male Connectorsand Female Ports
Metric Male Thread Female ThreadThread O.D. “A” I.D. “B”
mm in. mm in.M12 x 1.5 12 0.47 10,5 0.41M14 x 1.5 14 0.55 12,5 0.49M16 x 1.5 16 0.63 14,5 0.57M18 x 1.5 18 0.71 16,5 0.65M20 x 1.5 20 0.78 18,5 0.73M22 x 1.5 22 0.87 20,5 0.81M24 x 1.5 24 0.94 22,5 0.89M26 x 1.5 26 1.02 24,5 0.96M27 x 2 27 1.06 25 0.98M30 x 1.5 30 1.18 28,5 1.12M30 x 2 30 1.18 28 1.10M33 x 2 33 1.30 31 1.22M36 x 1.5 36 1.41 34,5 1.36M36 x 2 36 1.41 34 1.33M38 x 1.5 38 1.49 36,5 1.43M38 x 2 38 1.49 36 1.41M42 x 1.5 42 1.65 40,5 1.60M42 x 2 42 1.65 40 1.57M45 x 1.5 45 1.77 43,5 1.71M45 x 2 45 1.77 43 1.69M48 x 1.5 48 1.89 46,5 1.83M48 x 2 48 1.89 46 1.81M52 x 1.5 52 2.04 50,5 1.89M52 x 2 52 2.04 50 1.97
For DIN 3852 Whitworth pipe thread dimensions, see BSPT/BSPP dimensions. They are thesame.
371EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
Millimetrique andGAZ Series
BSPT/BSPP Threads
Millimetrique andGAZ ThreadsTubing “Gaz” MetricO.D. Pipe O.D. Thread Male Thread Female Thread“R” dim. “R” dim. size O.D. I.D.
mm in mm in mm in mm in6 0.24 M12 x 1.5 12 0.47 11 0.438 0.32 M14 x 1.5 14 0.55 12.5 0.4910 0.39 M16 x 1.5 16 0.63 14.5 0.5712 0.47 M18 x 1.5 18 0.71 16.5 0.6514 0.55 13.25 0.52 M20 x 1.5 20 0.78 18.5 0.7315 0.59 M22 x 1.5 22 0.87 20.5 0.8116 0.63 16.75 0.66 M24 x 1.5 24 0.94 22.5 0.8918 0.71 M27 x 1.5 27 1.06 25.5 1.0022 0.87 21.25 0.83 M30 x 1.5 30 1.18 28.5 1.1225 0.98 M33 x 1.5 33 1.30 31.5 1.2428 1.10 26.75 1.05 M36 x 1.5 36 1.41 34.5 1.3630 1.18 M39 x 1.5 39 1.54 37.5 1.4832 1.25 M42 x 1.5 42 1.65 40.5 1.6035 1.38 33.50 1.32 M45 x 1.5 45 1.77 43.5 1.7138 1.50 M48 x 1.5 48 1.89 46.5 1.8340 1.57 42.25 1.66 M52 x 1.5 52 2.04 50.5 1.9945 1.77 M54 x 2.0 54 2.12 52 2.05
48.25 1.90 M58 x 2.0 58 2.28 55 2.16
FrenchConnections
NominalInch Dash Thread Male Thread Female ThreadSize size size O.D. Inch O.D. Inch
fraction decimal fraction decimal1/8 02 1/8–28 3/8 0.38 11/32 0.351/4 04 1/4–19 33/64 0.52 15/32 0.473/8 06 3/8–19 21/32 0.65 19/32 0.601/2 08 1/2–14 13/16 0.82 3/4 0.755/8 10 5/8–14 7/8 0.88 13/16 0.803/4 12 3/4–14 11/32 1.04 31/32 0.971 16 1–11 15/16 1.30 17/32 1.2211/4 20 11/4–11 121/32 1.65 19/16 1.5611/2 24 11/2–11 17/8 1.88 125/32 1.792 32 2–11 211/32 2.35 21/4 2.26
BritishConnections
This BSPT (tapered) connec-tion is similar to the NPT,except that the thread pitchesare different in most sizes, andthe thread form and O.D.s are
close but not the same.Sealing is accomplished bythread distortion. A threadsealant is recommended.
*Frequently, the thread size is expressed as a fractional dimension preceded by the letter“G” or the letter “R”. The “G” represents a parallel thread and the “R” indicates a taperedthread. For example, BSPP 3/8–19 may be expressed as G 3/8, and BSPT 3/8–19 may beexpressed as R3/8.
The BSP (parallel) male is similar to the NPSM maleexcept the thread pitches aredifferent in most sizes.
The female swivel BSPP has atapered nose/Globeseal flare-less swivel which seals on thecone seat of the male.
This connection consists of acommon male and two differ-ent females. The MillimetriqueSeries is used with whole
number metric O.D. tubingand the GAZ Series is usedwith fractional number metricO.D. pipe size tubing.
British Standard Pipe(BSP)
372 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
JIS 30° MaleInverted Seat,Parallel Pipe Threads(Threads per JIS B 0202)
NominalThd. Size
Size (similar Male Thread Female ThreadSize (dash) to bspp) O.D. I.D.
fraction mm fraction mm1/4 6 (04) 1/4–19 33/64 13.2 15/32 11.93/8 9 (06) 3/8–19 21/32 16.7 19/32 15.31/2 12 (08) 1/2–14 13/16 21.0 3/4 19.23/4 19 (12) 3/4–14 11/32 26.4 31/32 24.61 25 (16) 1–11 15/16 33.3 17/32 30.911/4 32 (20) 11/4–11 121/32 41.9 19/16 39.611/2 38 (24) 11/2–11 17/8 47.8 125/32 45.52 50 (32) 2–11 211/32 59.7 21/4 57.4
The JIS parallel is similar to theBSPP connection. The JIS par-allel thread and the BSPP con-nection are interchangeable.
NominalThd. Size
Size (similar Male Thread Female ThreadSize (dash) to bspp) O.D. I.D.
fraction mm fraction mm1/4 6 (04) 1/4–19 33/64 13.2 15/32 11.93/8 9 (06) 3/8–19 21/32 16.7 19/32 15.31/2 12 (08) 1/2–14 13/16 21.0 3/4 19.23/4 19 (12) 3/4–14 11/32 26.4 31/32 24.61 25 (16) 1–11 15/16 33.3 17/32 30.911/4 32 (20) 11/4–11 121/32 41.9 19/16 39.611/2 38 (24) 11/2–11 17/8 47.8 125/32 45.52 50 (32) 2–11 211/32 59.7 21/4 57.4
JapaneseConnections
JIS 30° Male(Inverted) Seat,Metric Threads(Threads per JIS B 0207)
DashSize
Inch Equi- Thread Male Thread Female ThreadSize valent Size O.D. I.D.
fraction mm fraction mm6 04 M14 x 1.5 14 0.55 12.5 0.499 06 M18 x 1.5 18 0.71 16.5 0.6512 08 M22 x 1.5 22 0.87 20.5 0.8119 12 M30 x 1.5 30 1.18 28.5 1.1225 16 M33 x 1.5 33 1.30 31.5 1.2432 20 M42 x 1.5 42 1.65 40.5 1.60
The JIS parallel (metric) is thesame as the JIS parallel (PF),except for the thread differ-ence.
Tapered
ThreadO.D.
ThreadI.D.
Tapered
Male Half Female Half
JIS Tapered Pipe (PT)(Threads per JIS B 0203)
NominalThd. Size
Size (similar Male Thread Female ThreadSize (dash) to bspt) O.D. I.D.
fraction mm fraction mm1/4 6 (04) 1/4–19 33/64 13.2 15/32 11.93/8 9 (06) 3/8–19 21/32 16.7 19/32 15.31/2 12 (08) 1/2–14 13/16 21.0 3/4 19.23/4 19 (12) 3/4–14 11/32 26.4 31/32 24.61 25 (16) 1–11 15/16 33.3 17/32 30.911/4 32 (20) 11/4–11 121/32 41.9 19/16 39.611/2 38 (24) 11/2–11 17/8 47.8 125/32 45.52 50 (32) 2–11 211/32 59.7 21/4 57.4
The JIS tapered thread is simi-lar to the BSPT connection indesign, appearance and
dimensions. The JIS taperedthread and the BSPT connec-tion are interchangeable.
JIS 30° Female (Cone)Seat, Parallel PipeThreads(Threads per JIS B 0202)
The Japanese JIS 30° flare issimilar to the American SAE37° flare connection in applica-tion as well as sealing princi-
ples. However, the flare angleand dimensions are different.The threads are similar toBSPP.
373EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
JIS B 8363 4-BoltFlange*
This connection is commonlyused in fluid power systems.There are two pressure rat-ings. Type I (Code 61) isreferred to as the “standard”series and Type II (Code 62) isthe “6000 psi” series. Thedesign concept for both seriesis the same, but the bolt holespacing and flanged headdiameters are larger for thehigher pressure, Type II con-nection. Both metric and inchbolts are used.
The female (port) is anunthreaded hole with four boltholes in a rectangular patternaround the port. The male con-sists of a flanged head,grooved for an O-Ring, andeither a captive flange or splitflange halves with bolt holesto match the port. The sealtakes place on the O-Ring,which is compressed betweenthe flanged head and the flatsurface surrounding the port.The threaded bolts hold theconnection together.*JIS B 8363, ISO/DIS 6162, DIN 20066,and SAE J518 are interchangeable, exceptfor bolt sizes.
Size Portmm HoleInch mm Bolt Dimensions Bolt Hole Spacing [dash] (inch) mm & inch “A” mm (inch)
TYPE I TYPE II TYPE I TYPE II(Cd.61) (Cd. 62) (Cd. 61) (Cd. 62)
12 12.7 M8 x 1.25 x 30 M8 x 1.25 x 30(1/2) (0.50) 5/16–18 x 11/4 5/16–18 x 11/4 38.10 40.49[08] (1.50) (1.57)19 19.1 M10 x 1.5 x 30 M10 x 1.5 x 40(3/4) (0.75) 3/8–16 x 11/4 3/8–16 x 11/2 47.63 50.80[12] (1.88) (2.00)25 25.4 M10 x 1.5 x 30 M12 x 1.75 x 45(1) (1.00) 3/8–16 x 11/4 7/16–14 x 13/4 52.37 57.15[16] (2.06) (2.25)32 31.7 M12 x 1.5 x 40 M14 x 2 x 45(11/4) (1.25) 7/16–14 x 11/2 1/2–13 x 13/4 58.72 66.68[20] (2.31) 2.63)38 38.0 M12 x 1.75 x 40 M16 x 2 x 55(11/2) (1.50) 1/2–13 x 11/2 5/8–11 x 21/4 69.85 79.38[24] (2.75) (3.13)50 50.8 M12 x 1.75 x 40 M20 x 2.5 x 70(2) (2.00) 1/2–13 x 11/2 3/4–10 x 23/4 77.77 96.82[32] (3.06) (3.81)
Inch Flanged Head size dia. “K”
Type I Type IIBar (Cd.61) Bar (Cd. 62)mm in mm in
1/2 30,18 1.19 31,75 1.253/4 38,10 1.50 41,28 1.631 44,45 1.75 47,63 1.8811/4 50,80 2.00 53,98 2.1311/2 60,33 2.38 63,50 2.502 71,42 2.81 79,38 3.13
JIS 210 Kgf/cm2
4-Bolt Square Flange Bolt Size Boltmm (Bolt Dim. Dim. Dim. Hole
Approx. length “A” “B” “C” Dia “D”Size inch for long mm mm mm mmmm size design) (inch) (inch) (inch) (inch)
12 1/2 M10 x 1.5 x 55 63 40 22 11(80) (2.48) (1.57) (0.87) (0.43)
19 3/4 M10 x 1.5 x 55 68 45 22 11(80) (2.67) (1.77) (0.87) (0.43)
25 1 M12 x 1.75 x 70 80 53 28 13(100) (3.15) (2.09) (1.10) (0.51)
32 11/4 M12 x 1.75 x 70 90 63 28 13(100) (3.54) (2.48) (1.10) (0.51)
38 11/2 M16 x 2.0 x 90 100 70 36 18(130) (3.94) (2.76) (1.42) (0.71)
50 2 M16 x 2.0 x 90 112 80 36 18(130) (4.41) (3.15) (1.42) (0.71)
JIS 210 Kgf/cm2 O-Ring Nominal Dim. Dim.size “D” “W”mm mm mm
12 24.4 ± 0.15 3.1 ± 0.119 29.4 ± 0.15 3.1 ± 0.125 34.4 ± 0.15 3.1 ± 0.132 39.4 ± 0.15 3.1 ± 0.138 49.4 ± 0.15 3.1 ± 0.150 59.4 ± 0.15 3.1 ± 0.1
The JIS 4-Bolt square flangeconnection is similar in con-cept to the SAE 4-bolt flangeconnection, except that theJIS bolt pattern is square andthe flange itself is different.
374 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
How to Identify O-Ring Pilot Thread Sizes
This connection is common toair conditioning systems, bothin vehicle and commercialapplications. Both the male andfemale halves of the connec-tions have a pilot, either long orshort. The seal takes place bycompressing an O-ring adjacentto the bead of the tube. Thethreads hold the connectiontogether mechanically.
O.D. (inch) I.D. (inch)Inch Dash Nominal O.D. (inch) O.D. (inch) Nominal I.D. (inch) I.D. (inch)Size Size Thread Fraction Decimal Thread Fraction Decimal3/8 06 5/8 - 18 5/8 0.62 5/8 - 18 9/16 0.571/2 08 3/4 - 18 3/4 0.75 3/4 - 16 11/16 0.695/8 10 7/8 - 18 7/8 0.87 7/8 - 14 13/16 0.813/4 12 11/16 -16 11/16 1.06 11/16 - 14 1 0.99
NominalInch Tube Bead O.D. Pilot Bead O.D. PilotSize Size (inch) Length (inch) Length3/8 06 0.52 0.28 0.52 0.191/2 08 0.64 0.39 0.64 0.195/8 10 0.77 0.39 0.77 0.193/4 12 0.91 0.39 0.91 0.19
Male Thread Female Thread
Long Pilot Short Pilot
375EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
SAE O-ring Boss SAE O-ring BossDash SAE J1926 SAE J1926Size Male Pipe with 37° Flare J514 with ORS J1453
Straight and Angled Straight and Adjustable Straight and AdjustableDimension “B” Dimension “B” Dimension “B”mm in mm in mm in
–02 6,4 0.25–04 9,7 0.38 9,1 0.36 10,9 0.43–05 9,1 0.36 10,9 0.43–06 9,7 0.38 9,1 0.39 11,9 0.47–08 12,7 0.50 10,9 0.43 14,0 0.55–10 12,7 0.50 16,0 0.63–12 15,7 0.62 15,0 0.59 18,5 0.73–14 15,0 0.59–16 17,5 0.69 15,0 0.59 18,5 0.73–20 17,5 0.69 15,0 0.59 18,5 0.73–24 17,5 0.69 15,0 0.59 18,5 0.73–32 19,1 0.75 15,0 0.59
Dimensions may vary due totolerance conditions.Listed below are the threadengagement dimensions (B)which must be taken into con-sideration when making con-nection with ports or appropri-ate female adapters. The “B” dimension must besubtracted from the overalllength (A) to insure proper con-nection.
ThreadEngagementNominalDimensions
Allowable bulkheadthickness for ORS:
For 37° Flare:
Dash HoleSize Diameter ORS Bulkhead Thickness
MIN MAX
in mm in mm in –04 .575 +.015/–.000 5,1 0.20 12,7 0.50–06 .700 +.015/–.000 5,1 0.20 15,0 0.59–08 .825 +.015/–.000 5,6 0.22 15,0 0.59–10 1.015 +.015/–.000 5,8 0.23 15,0 0.59–12 1.200 +.015/–.000 6,4 0.25 15,0 0.59–16 1.450 +.015/–.000 6,4 0.25 15,2 0.60–20 1.715 +.015/–.000 6,4 0.25 15,2 0.60–24 2.030 +.015/–.000 6,4 0.25 15,2 0.60
Dash Hole 37° Bulkhead 37° BulkheadSize Diameter Thickness Straights Thickness Shapes
MIN MAX MIN MAX
in mm in mm in mm in mm in–03 .391 +.016/–.000 1,3 0.05 10,4 0.41 3,3 0.13 6,4 0.25–04 .453 +.016/–.000 1,3 0.05 10,4 0.41 3,3 0.13 7,1 0.28–05 .516 +.016/–.000 1,3 0.05 10,4 0.41 3,3 0.13 7,1 0.28–06 .578 +.016/–.000 1,3 0.05 11,2 0.44 3,3 0.13 7,6 0.30–08 .766 +.016/–.000 1,3 0.05 11,2 0.44 4,1 0.16 8,6 0.34–10 .891 +.016/–.000 1,3 0.05 11,9 0.47 4,1 0.16 9,1 0.36–12 1.076 +.016/–.000 1,3 0.05 11,9 0.47 4,1 0.16 9,7 0.38–16 1.328 +.016/–.000 1,3 0.05 11,9 0.47 4,1 0.16 9,7 0.38–20 1.656 +.031/–.000 1,3 0.05 11,9 0.47 4,1 0.16 9,7 0.38–24 1.906 +.031/–.000 1,3 0.05 11,9 0.47 4,1 0.16 9,7 0.38
Dimensions may vary due to tolerance conditions.
376 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
SAE100R2 Female *StraightMaximum SAE SAE Male Female Pipe *Male Thread Female
Dash Inch Operating 37° Flare 37° Flare Pipe Pipe Swivel O-ring O-ring O-ringSize Size Pressure Male (JIC) Swivel (JIC) NPTF NPTF NPSM Boss Adjustable Boss
bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi–2 1/8 700,0 10000 350,0 5000 420,0 6000–4 1/4 350,0 5000 595,0 8500 385,0 5500 655,0 9500 315,0 4500 350,0 5000 525,0 7500 315,0 4500 315,0 4500–5 5/16 297,0 4250 595,0 8500 350,0 5000 525,0 7500 245,0 3500 245,0 3500–6 3/8 280,0 4000 490,0 7000 280,0 4000 560,0 8000 245,0 3500 280,0 4000 525,0 7500 280,0 4000 245,0 3500–8 1/2 245,0 3500 420,0 6000 280,0 4000 420,0 6000 245,0 3500 245,0 3500 525,0 7500 280,0 4000 210,0 3000–10 5/8 192,0 2750 385,0 5500 210,0 3000 525,0 7500 280,0 4000 175,0 2500–12 3/4 157,0 2250 280,0 4000 210,0 3000 350,0 5000 210,0 3000 245,0 3500 350,0 5000 245,0 3500 124,1 1800–14 7/8 140,0 2000 280,0 4000 210,0 3000 350,0 5000 210,0 3000 117,2 1700–16 1 140,0 2000 245,0 3500 175,0 2500 280,0 4000 175,0 2500 210,0 3000 315,0 4500 175,0 2500 112,0 1600–20 11/4 113,0 1625 245,0 3500 140,0 2000 210,0 3000 140,0 2000 140,0 2000 315,0 4500 140,0 2000 105,0 1500–24 11/2 87,0 1250 140,0 2000 105,0 1500 140,0 2000 105,0 1500 105,0 1500 245,0 3500 140,0 2000 105,0 1500–32 2 78,0 1125 87,0 1250 87,0 1250 140,0 2000 98,0 1400 105,0 1500 140,0 2000*For non “ORS” adapters
SAE100r2Maximum ORS For ORS For ORS Male Male
Dash Inch Operating ORS Female Adapters Adapters SAE Flange Flange SAE InvertedSize Size Pressure Male Swivel ORB/STR ORB/ADJ Flareless Code 61 Code 62 Flare
bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi–2 1/8–4 1/4 350,0 5000 630,0 9000 630,0 9000 630,0 9000 420,0 6000 420,0 6000 255,1 3700–5 5/16 297,0 4250 206,8 3000–6 3/8 280,0 4000 630,0 9000 630,0 9000 630,0 9000 420,0 6000 420,0 6000 165,4 2400–8 1/2 245,0 3500 630,0 9000 560,0 8000 630,0 9000 420,0 6000 420,0 6000 350,0 5000 420,0 6000 117,2 1700–10 5/8 192,0 2750 630,0 9000 560,0 8000 630,0 9000 420,0 6000 350,0 5000 131,0 1900–12 3/4 157,0 2250 420,0 6000 420,0 6000 420,0 6000 420,0 6000 315,0 4500 350,0 5000 420,0 6000 103,4 1500–14 7/8 140,0 2000–16 1 140,0 2000 420,0 6000 420,0 6000 420,0 6000 350,0 5000 280,0 4000 350,0 5000 420,0 6000–20 11/4 113,0 1625 315,0 4500 315,0 4500 315,0 4500 315,0 4500 280,0 4000 420,0 6000–24 11/2 87,0 1250 280,0 4000 280,0 4000 280,0 4000 210,0 3000 210,0 3000 420,0 6000–32 2 78,0 1125 210,0 3000 420,0 6000
The following table is abreakdown of hydraulicpressure performance bythread style and size forSTEEL products. The tableis based on limited labora-tory test data and is intend-ed only as an approximateguide to field perform anceof Eaton products. Figuresshown are maximum oper-
ating pressures in BAR(psi), based upon a 4:1safety factor relative to theconnection minimum burstpressure. Testing was con-ducted at SAE recommend-ed assembly torque in hard-ened test blocks. The pres-sure rating must be adjust-ed for any change in matingpart material. The maximum
operating pressure for theadapter or tube fitting bodymust be the lower of thechosen mating end types.
Thread StylePressurePerformance/MaximumOperatingPressure
377EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
Tube Dash Tubing Wall Thickness (in inches)O.D. Size
.028 .035 .049 .065 .083 .095 .109 .120 .134 .148 .156 .188bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi bar psi
.19 –03 297,0 4250 375,0 5450
.25 –04 213,0 3100 272,0 3950 396,0 5750 420,0 6000
.31 –05 169,0 2450 213,0 3100 315,0 4500 420,0 6000
.38 –06 140,0 2000 175,0 2550 251,0 3650 350,0 5000 420,0 6000 420,0 6000
.50 –08 127,0 1850 186,0 2700 251,0 3650 335,0 4800 388,0 5550 420,0 6000 420,0 6000
.62 –10 105,0 1500 145,0 2100 196,0 2850 258,0 3750 299,0 4350 353,0 5050 392,0 5600
.75 –12 84,0 1200 122,0 1750 162,0 2350 210,0 3050 248,0 3550 286,0 4150 322,0 46001.00 –16 62,0 900 89,0 1300 122,0 1750 157,0 2250 182,0 2600 210,0 3000 231,0 3350 262,0 3800 294,0 42001.25 –20 70,0 1000 93,0 1350 122,0 1750 143,0 2050 162,0 2350 182,0 2650 189,0 2700 203,0 2950 217,0 3100 259,0 3750 1.50 –24 79,0 1150 100,0 1450 119,0 1700 134,0 1950 148,0 2150 171,0 2450 171,0 2450 182,0 2600 220,0 31502.00 –32 58,0 850 77,0 1100 87,0 1250 100,0 1450 112,0 1600 126,0 1800 140,0 2000 147,0 2100 178,0 2550
Maximum Operating PressuresBar/PSI for Hydraulic Tubing(SAEJ356, J524, J525, J526, J527)
Recommended Wall Thickness(Inches) for Tube Fitting Applications
Recommended HydraulicTubing Material Specifications
Maximum operating pressureratings at specified wall thick-ness are based upon recom-mended tubing ratings perSAEJ1065 as well as limitedlaboratory test data. Operatingpressures are based upon a
4:1 safety factor relative totube burst data. Eaton recom-mends a maximum operatingpressure of the joint which isthe lesser of the tubing ratingor the mating connector rating.
Hydraulic tubing materialdescription: SAEJ356 electricresistance welded flash con-trolled low carbon steel,SAEJ524 seamless annealedlow carbon steel, SAEJ525electric resistance welded coldworked annealed, SAEJ526
single wall welded low carbonsteel (automotive), SAEJ527brazed double wall low carbonsteel (automotive). The maxi-mum hardness of the abovetubing should not exceedRockwell B65.
Versil-Flare Versil-Flare ORS-BR ORS-TFSAE 37° SAE 37° SAE O-Ring SAE O-ring
Tube Dash Flare Flareless Face Seal Face Seal
.19 –03 .028 – .035 .028 – .035
.25 –04 .028 – .065 .028 – .065 .028 – .065 .028 – .065
.31 –05 .028 – .065 .028 – .065
.38 –06 .028 – .065 .028 – .095 .035 – .083 .028 – .065
.50 –08 .035 – .083 .035 – .120 .035 – .109 .035 – .120
.62 –10 .035 – .095 .035 – .120 .035 – .120 .035 – .095
.75 –12 .035 – .109 .035 – .120 .035 – .120 .049 – .1201.00 –16 .035 – .120 .035 – .134 .049 – .148 .049 – .1341.25 –20 .049 – .120 .049 – .188 .049 – .188 .049 – .1561.50 –24 .065 – .120 .065 – .188 .065 – .188 .065 – .1882.00 –32 .065 – .134 .065 – .188
Hydraulic Tubing SAE Specifications
Versil-Flare Versil-Flare ORS-BR ORS-TFSAE 37° SAE 37° SAE O-ring SAE O-ringFlare Flareless Face Seal Face Seal
SAEJ524 SAEJ356 SAEJ356 SAEJ356SAEJ525 SAEJ524 SAEJ524 SAEJ524
SAEJ525 SAEJ525 SAEJ525SAEJ527 SAEJ526 SAEJ526
378 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Metric ThreadDimensionsConversionAdapters
Sealing is achieved bymeans of an O-Ring, retain-ing washer and a properlymachined port. The O-Ringis “captured” by the I.D. of
the retaining washer. Theport may be of the spotfaced or a flat machinedsurface as long as the D6dimension is met.
Assembly instructions foradjustable type adaptersare presented on page 309.
Dimensions in mm
Thread Size M 10 x 1 M 12 x 1.5 M 14 x 1.5 M 16 x 1.5 M 18 x 1.5 M 20 x 1.5 M 22 x 1.5 M 26 x 1.5 M 27 x 2 M 33 x 2 M 42 x 2 M 48 x 2
F Thread Dia. 10.0 12.0 14.0 16.0 18.0 20.0 22.0 26.0 27.0 33.0 42.0 48.0A max 1.0 1.5 1.5 1.5 2.0 2.0 2.5 2.5 2.5 2.5 2.5 2.5B min (full thread) 12.0 12.0 12.0 12.0 12.0 14.0 14.0 16.0 16.0 18.0 20.0 22.0B1 min 13.5 18.5 18.5 18.5 18.5 20.5 20.5 22.5 24.0 26.0 28.0 30.0D max 15.7 18.7 19.7 23.2 26.2 28.2 30.2 35.2 36.2 43.2 52.7 58.7D6 min 16.2 19.2 20.2 23.7 26.9 28.9 30.7 35.7 36.7 44.4 53.4 59.9D7 max 10.2 12.2 14.2 16.2 18.2 20.2 22.2 26.2 27.2 33.3 42.3 48.3
Sealing is achieved bymeans of an O-Ring, retain-ing washer and a properlymachined port.
The O-Ring is “captured”by the I.D. of the retainingwasher. The compression iscontrolled by the thicknessof the retaining washer.
The port may be of thespot faced or a flatmachined surface as longas the D6 dimension is met.
Thread Size G 1/8"-28 G 1/4"-19 G 3/8"-19 G 1/2"-14 G 3/4"-14 G 1"-11 G 11/4"-11 G 11/2"-11
mm in mm in mm in mm in mm in mm in mm in mm inF Thread Dia. 9,7 0.38 13,2 0.50 16,7 0.66 20,9 0.83 26,4 1.04 33,3 1.31 41,9 1.65 47,8 1.88A max 1,0 0.04 2,0 0.08 2,05 0.10 2,5 0.10 2,5 0.10 2,5 0.10 2,5 0.10 2,5 0.10B min 8,0 0.31 12,0 0.47 12,0 0.47 14,0 0.63 16,0 0.63 18,0 0.71 20,0 0.79 22,0 0.87B1 min (full thread) 13,0 0.51 18,5 0.73 18,5 0.73 22,0 0.94 24,0 0.94 27,0 1.06 29,0 1.14 31,0 1.22D max 15,7 0.62 19,7 0.78 24,0 0.94 28,7 1.38 35,2 1.38 43,2 1.70 52,7 2.07 58,7 2.31D6 min 16,2 0.64 20,2 0.81 24,9 0.98 29,4 1.43 36,4 1.43 44,4 1.75 53,4 2.10 59,9 2.36D7 max 10,0 0.39 13,4 0.53 16,9 0.67 21,2 1.05 26,7 1.05 33,6 1.32 42,3 1.67 48,2 1.90
BSPT (Tapered)Threads
Port Sealing
Sealing is achieved bymeans of metal to metaldeformation of the adapterand port threads.
Thread Size R 1/8"-28 R 1/4"-19 R 3/8"-19 R 1/2"-14 R 3/4"-14 R 1"-11 R 11/4"-11 R 1 1/2"-11
mm in mm in mm in mm in mm in mm in mm in mm inB2 min (full thread) 5,5 0.22 8,5 0.33 8,5 0.33 10,5 0.41 13,0 0.51 14,5 0.57 17,0 0.67 17,0 0.67
EQUIVALENT TODIN 3852 FORM XDIN 3852 LARGE SPOTFACE
BSPP ( Parallel)Threads
379EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
RecommendedParallel ConnectionAssembly Torque
Eaton recommends that atorque wrench be used toassure proper fittingassembly of these connec-tions.
The values listed are forsteel connections. ContactEaton for torque values forother materials.
ORS
Swivel SwivelThread Nut Nut
Dash Size Torque TorqueSize (inches) lb.-ft. Newton Meters
–04 9/16-18 10-12 14-16–06 11/16-16 18-20 24-27–08 13/16-16 32-35 43-47–10 1-14 46-50 62-68–12 13/16-12 65-70 88-95–16 17/16-12 92-100 125-136–20 111/16-12 125-140 170-190–24 2-12 150-165 204-224
SAE 37˚ (JIC)Swivel Swivel
Thread Nut NutDash Size Torque TorqueSize (inches) lb.-ft. Newton Meters
–04 7/16-20 11-12 15-16–05 1/2-20 15-16 20-22–06 9/16-18 18-20 24-28–08 3/4-16 38-42 52-58–10 7/8-14 57-62 77-85–12 11/16-12 79-87 108-119–16 15/16-12 108-113 148-154–20 15/8-12 127-133 173-182–24 17/8-12 158-167 216-227–32 21/2-12 245-258 334-352
Metric
Thread Size Straight Adapter or Locknut Torque
mm lb.-ft. Newton MetersM10 x 1 13-15 18-20M12 x 1.5 15-19 20-25M14 x 1.5 19-23 25-30M16 x 1.5 33-40 45-55M18 x 1.5 37-44 50-60M20 x 1.5 52-66 70-90M22 x 1.5 55-70 75-95M26 x 1.5 81-96 110-130M27 x 2 96-111 130-150M33 x 2 162-184 220-250M42 x 2 170-192 230-260M48 x 2 258-347 350-470
BSPP
NominalThread Size Straight Adapter or Locknut Torque
inches** lb.-ft. Newton MetersG 1/8-28 13-15 18-20G 1/4-19 19-23 25-30G 3/8-19 33-40 45-55G 1/2-14 55-70 75-95G 3/4-14 103-118 140-160G 1-11 162-184 220-250G 11/4-11 170-192 230-260G 11/2-11 258-347 350-470
**”G” denotes parallel threads, other than ISO 6149. (Port connection only)
Straight Thread O-Ring Boss Low Pressure with 37° (SAEJ514)
Jam Nut or Jam Nut orThread Straight Straight
Dash Size Fitting Torque Fitting TorqueSize (inches) lb.-ft. Newton Meters
–03 3/8-24 8-9 12-13–04 7/16-20 13-15 18-20–05 1/2-20 14-15 19-21–06 9/16-18 23-24 32-33–08 3/4-16 40-43 55-57–10 7/8-14 43-48 59-64–12 11/16-12 68-75 93-101–14 13/16-12 83-90 113-122–16 15/16-12 112-123 152-166–20 15/8-12 146-161 198-218–24 17/8-12 154-170 209-230–32 21/2-12 218-240 296-325
Straight Thread O-Ring Boss High Pressure with ORS (J1453)
Jam Nut or Jam Nut orThread Straight Straight
Dash Size Fitting Torque Fitting TorqueSize (inches) lb.-ft. Newton Meters
–03 3/8-24 8-10 11-13–04 7/16-20 14-16 20-22–05 1/2-20 18-20 24-27–06 9/16-18 24-26 33-35–08 3/4-16 50-60 68-78–10 7/8-14 72-80 98-110–12 11/16-12 125-135 170-183–14 13/16-12 160-180 215-245–16 15/16-12 200-220 270-300–20 15/8-12 210-280 285-380–24 17/8-12 270-360 370-490
380 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
SPECIALTY &
TRU
CK HO
SELO
W &
MED
IUM
PRESSU
RE HO
SEH
IGH
PRESSURE H
OSE
HO
SE FITTING
SA
DA
PTERS &TU
BE FITTIN
GS
ACCESSO
RIES &
ASSEMBLY IN
STRUCTIONS
HO
SE ASSEM
BLY
EQU
IPMEN
TA
PPEND
ICIES
Proper TubeInstallation
Figure 1 Figure 2 Figure 3 Figure 4
CORRECT
INCORRECT
CORRECT
INCORRECT
CORRECT
INCORRECT
CORRECT
INCORRECT
When compared to rigidpipe, hydraulic tubing offersthe following advantages:
1. Size for size, tubing islighter in weight, easierto handle and can bebent more easily thaniron pipe.
2 Bent tubing reduces pres-sure drop and turbulencein the system because iteliminates sudden changein the direction of thefluid flow.
3.Hydraulic tubing reducesthe number of connec-tions required, thus reducing material andlabor costs.
4.Fewer joints means lowercosts and fewer points ofpotential leakage.
5.The use of tube fittingsmakes every joint a unionwhich permits easier,faster maintenance andrepair work.
6.The ORS-TF Tube Fittingeliminates the need forthreading, brazing orwelding.
Tube bending
To reduce the number offittings in a tube assembly,bend the tubing wheneverpossible.
Steel tubing can be bent inmany sizes by using a handbender designed for steeltubing. For production quan-tities, or for larger sizes, apower bending tool is gen-erally used. Contact Eatonfor additional tube bendinginformation.
Tube routing and installation
Tubing manufacturers willadvise the correct radii forvarious types and wallthicknesses of tubing.Kinks, flattened bends,wrinkles and tube breakagecan be avoided by the useof proper tube bendingequipment.
Avoid straight line connec-tions whenever possible,especially in short runs.
Fluid conveying systems(see figures 2, 3 and 4)should be designed to fol-low the contour of theequipment. They are easierto install and present aneater appearance. Longruns should be supported bybrackets or clamps. Allheavy systems componentsshould be bolted or clampedto eliminate tubing fatigue.
Inspect the tubing to seethat it conforms to therequired specificationsbefore installation.
Tubes should align with thecenter line of the fittings,without distortion or ten-sion. Tubing should not besprung into position (seefigure 1) to be assembledto the fitting. If this occursthe tubing has not beenproperly fabricated, andwhen installed and con-nected, places the tubingunder stress.
381EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APP
END
ICIE
SH
OSE
ASS
EMB
LY
EQU
IPM
ENT
ACC
ESSO
RIES
&
ASSE
MBL
Y IN
STRU
CTIO
NS
AD
APT
ERS
&TU
BE
FITT
ING
S
HO
SE F
ITTI
NG
SH
IGH
PRE
SSU
RE H
OSE
LOW
& M
EDIU
M
PRES
SURE
HO
SESP
ECIA
LTY
&
TRU
CK H
OSE
fractions decimals decimals fractions decimals decimals fractions decimals decimals fractions decimals decimals
Conversions
Inches Millimeters Inches Millimeters Inches Millimeters Inches Millimeters
1/64 .016 .3971/32 .031 .7943/64 .047 1.1911/16 .063 1.5885/64 .078 1.9843/32 .094 2.3817/64 .109 2.7781/8 .125 3.1759/64 .141 3.5725/32 .156 3.96911/64 .172 4.3663/16 .188 4.76313/64 .203 5.1597/32 .219 5.55615/64 .234 5.9531/4 .250 6.350
17/64 .266 6.7479/32 .281 7.14419/64 .297 7.5415/16 .313 7.93821/64 .328 8.33411/32 .344 8.73123/64 .359 9.1283/8 .375 9.52525/64 .391 9.92213/32 .406 10.31927/64 .422 10.7167/16 .438 11.11329/64 .453 11.50915/32 .469 11.90631/64 .484 12.3031/2 .500 12.700
33/64 .516 13.09717/32 .531 13.49435/64 .547 13.8919/16 .563 14.28837/64 .578 14.68419/32 .594 15.08139/64 .609 15.4785/8 .625 15.87541/64 .641 16.27221/32 .656 16.66943/64 .672 17.06611/16 .688 17.46345/64 .703 17.85923/32 .719 18.25647/64 .734 18.6533/4 .750 19.050
49/64 .766 19.44725/32 .781 19.84451/64 .797 20.24113/16 .813 20.63853/64 .828 21.03427/32 .844 21.43155/64 .859 21.8287/8 .875 22.22557/64 .891 22.62229/32 .906 23.01959/64 .922 23.41615/16 .938 23.81361/64 .953 24.20931/32 .969 24.60663/64 .984 25.003
1 1.000 25.400
0.25 2.5 350.3 3 450.35 3.5 500.4 4 560.4 4 620.5 5 700.6 6 900.7 7 1000.8 8 1120.85 8.5 1251 10 1401.05 10.5 1501.25 12.5 1801.4 14 2001.6 16 2251.7 17 2502.1 21 3002.4 24 3502.6 26 3752.8 28 4003.5 35 5003.9 39 565
4.2 42 6004.3 43 6254.9 49 7005 50 7255.2 52 7505.6 56 8006.1 61 8757 70 10007.8 78 11258.4 84 12008.7 87 12509.8 98 140010 100 145010.5 105 150011.2 112 160011.3 113 162512.2 122 175014 140 200015.7 157 225016.8 168 240017.5 175 250019.2 192 2750
20 200 290021 210 300022.4 224 320022.7 227 325024.5 245 350028 280 400029.7 297 425031.5 315 450033.5 335 480035 350 500038.5 385 550040 400 580042 420 600043.5 435 625045.5 455 650049 490 700052.5 525 750056 560 800059.5 595 850061 610 875063 630 900070 700 10000
77 770 1100078 780 1125080 800 1160084 840 1200087 870 1250098 980 14000112 1120 16000119 1190 17000122 1220 17500140 1400 20000157 1570 22500160 1600 23200168 1680 24000175 1750 25000210 2100 30000245 2450 35000280 2800 40000315 3150 45000350 3500 50000
Mpa Bar PSI Mpa Bar PSI Mpa Bar PSI Mpa Bar PSI
Inch/MillimeterConversion Table
Multiply inches x 25.4 =Millimeters
A new method for calculat-ing the equivalent metricconversion to Mpa from psiwas utilized. This methodprovides an extremely easyand consistent method ofconversion to arrive at arounded metric units using
7 Mpa for each 1000 psi.The resulting Mpa pressurein never more than 1.7%higher that the mathemati-cally correct Mpa unit whenthe pressure in higher than250 psi. All operating pres-sures of SAE J517 hoses
are above 250 psi exceptfor most of 100R4 and the76mm (-48) and larger sizesof 100R5. Therefore allfiles of previous test resultsshould not be compro-mised.
Pressure ConversionTable
(Per SAE J517 Appendix A)