A&E Specifications

AMT-12

Loudspeaker shall be a full range two-way speaker utilizing a 12” woofer and a 1” exit Ferrofluid cooled compression driver mounted to a 65-degree horizontal by 65-degree vertical horn. The unit shall have a frequency response of 60Hz to 20kHz +/-3dB and a maximum long term SPL of 119dB with a sensitivity of 96dB. The loudspeaker shall have a light weight, impact resistant molded enclosure with two dual input connectors (NL4 and ¼” Phone Type), an integral 1 3/8” tri-pod cup and four M8 rigging points. The speaker shall be an Apogee Sound AMT-12.

AMT-15

Loudspeaker shall be a full range two-way speaker utilizing a 15” woofer and a 1” exit Ferrofluid cooled compression driver mounted to a 60-degree horizontal by 45-degree vertical horn. The unit shall have a frequency response of 50Hz to 20kHz +/-3dB and a maximum long term SPL of 123dB with a sensitivity of 98dB. The loudspeaker shall have a light weight, impact resistant molded enclosure with two dual input connectors (NL4 and ¼” Phone Type), an integral 1 3/8” tri-pod cup and four M8 steel backed rigging points. The speaker shall be an Apogee Sound AMT-15.

AFI-Point 5

Loudspeaker shall be a full range two-way speaker utilizing a 5.25” moisture stabilized woofer and a 1/2” Mylar tweeter. The unit shall have a frequency response of 100Hz to 20kHz +/-3dB (-10dB @ 60Hz), a maximum long term SPL of 104dB with a sensitivity of 89dB and a coverage angle of 100-degrees horizontal by 100-degrees vertical. The speaker shall be an Apogee Sound AFI-Point 5.

AFI-205

Loudspeaker shall be a full range three-way speaker utilizing a 10” moisture stabilized subwooofer in a band-pass configuration, two baffle loaded 5.25” moisture stabilized mid-woofers and two 1” Ferrofluid cooled dome tweeters. The unit shall have a frequency response of 44Hz to 20kHz +/-3dB, a maximum long term SPL of 109dB with a sensitivity of 89dB and a coverage angle of 120-degrees horizontal by 90-degrees vertical. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input on a #8 barrier strip. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as a fly points. The speaker shall be an Apogee Sound AFI-205.

AFI-205SX

Outdoor loudspeaker shall be a full range three-way speaker utilizing a 10” moisture stabilized subwooofer in a band-pass configuration, two baffle loaded 5.25” moisture stabilized mid-woofers and two 1” Ferrofluid cooled dome tweeters. The unit shall have a frequency response of 44Hz to 20kHz +/-3dB, a maximum long term SPL of 109dB with a sensitivity of 89dB and a coverage angle of 120-degrees horizontal by 90-degrees vertical. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input on a #8 barrier strip. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grill shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as a fly points. The speaker shall be an Apogee Sound AFI-205SX.

5/1/09

AFI-1s2

Loudspeaker shall be a full range two-way speaker utilizing an 8” moisture stabilized woofers and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 75-degree horizontal by 60-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 15.5kHz +/-3dB and a maximum long term SPL of 112dB with a sensitivity of 93dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-1s2.

AFI-1s2SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing an 8” moisture stabilized woofers and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 75-degree horizontal by 60-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 15.5kHz +/-3dB and a maximum long term SPL of 112dB with a sensitivity of 93dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speaker input panel shall be housed inside a watertight ABS junction box. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-1s2SX.

AFI-2s2

Loudspeaker shall be a full range two-way speaker utilizing two 8” moisture stabilized woofers and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 75-degree horizontal by 60-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 15.5kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 96dB and have an impedance of 16 ohms. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-2s2.

AFI-2s2SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing two 8” moisture stabilized woofers and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 75-degree horizontal by 60-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 15.5kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 96dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speaker input panel shall be housed inside a watertight ABS junction box. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-2s2SX.

5/1/09

AFI-WA

Loudspeaker shall be a full range three-way speaker utilizing an 8” moisture stabilized woofer, a 6.5” moisture stabilized midrange, and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 120-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 17.5kHz +/-3dB and a maximum long term SPL of 118dB with a sensitivity of 94dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-WA.

AFI-WA SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing an 8” moisture stabilized woofer, a 6.5” moisture stabilized midrange and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 120-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 66Hz to 17.5kHz +/-3dB and a maximum long term SPL of 118dB with a sensitivity of 94dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-WASX.

AFI-3

Loudspeaker shall be a full range two-way speaker utilizing a 10” moisture stabilized woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 60-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 61Hz to 20kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-3.

AFI-3W

Loudspeaker shall be a full range two-way speaker utilizing a 10” moisture stabilized woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 90-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 61Hz to 20kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-3W.

5/1/09

AFI-3SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 10” moisture stabilized woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 60-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 61Hz to 20kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speaker input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-3SX.

AFI-3WSX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 10” moisture stabilized woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 90-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 61Hz to 20kHz +/-3dB and a maximum long term SPL of 120dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speaker input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-3WSX.

AFI-4

Loudspeaker shall be a full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 60-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-4.

AFI-4W

Loudspeaker shall be a full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 90-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-4W.

5/1/09

AFI-4SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 60-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grill shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-4SX.

AFI-4WSX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 90-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-4WSX.

AFI-4M

Floor monitor shall be a low profile, multi-angle full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 60-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood and have steel protective skids on two surfaces. Input connection shall be 2 Neutrik NL4MPR connectors, one on each cabinet end. The speaker shall have two integral handles that cannot be used as fly points. The floor monitor shall be an Apogee Sound AFI-4M.

AFI-4MW

Floor monitor shall be a low profile, multi-angle full range two-way speaker utilizing a 12” Ferrofluid cooled, moisture stabilized, neodymium woofer and a 1” exit Ferrofluid cooled compression driver mounted to a rotatable 90-degree horizontal by 45-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 58Hz to 20kHz +/-3dB and a maximum long term SPL of 121dB with a sensitivity of 99dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood and have steel protective skids on two surfaces. Input connection shall be 2 Neutrik NL4MPR connectors, one on each cabinet end. The speaker shall have two integral handles that cannot be used as fly points. The floor monitor shall be an Apogee Sound AFI-4MW.

5/1/09

AFI-8

Loudspeaker shall be a full range two-way speaker utilizing a 15” Ferrofluid cooled, moisture stabilized woofer and a 2” exit Ferrofluid cooled compression driver mounted to a 60-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 46Hz to 20kHz +-3dB and a maximum long term SPL of 124dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-8.

AFI-8W

Loudspeaker shall be a full range two-way speaker utilizing a 15” Ferrofluid cooled, moisture stabilized woofer and a 2” exit Ferrofluid cooled compression driver mounted to a 90-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 46Hz to 20kHz +-3dB and a maximum long term SPL of 124dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-8W.

AFI-8SX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 15” Ferrofluid cooled, moisture stabilized woofer and a 2” exit Ferrofluid cooled compression driver mounted to a 60-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 46Hz to 20kHz +-3dB and a maximum long term SPL of 124dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grill shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-8SX.

AFI-8WSX

Outdoor loudspeaker shall be a full range two-way speaker utilizing a 15” Ferrofluid cooled, moisture stabilized woofer and a 2” exit Ferrofluid cooled compression driver mounted to a 90-degree horizontal by 40-degree vertical non-resonant urethane horn. The unit shall have a frequency response of 46Hz to 20kHz +-3dB and a maximum long term SPL of 124dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept a third party articulating mount and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-8WSX.

5/1/09

AFI-9

Loudspeaker shall be a high power full range three-way speaker utilizing two 12” Ferrofluid cooled, moisture stabilized neodymium woofers, two 6.5” moisture stabilized midrange drivers and a 2” exit, 4” diaphragm Ferrofluid cooled neodymium compression driver mounted to a large format 60-degree horizontal by 40-degree vertical non-resonant urethane horn. Mid and high frequencies shall be Point Source Coupled to the mid/high horn. The unit shall have a frequency response of 55Hz to 20kHz +/-3dB and a maximum long term SPL of 130dB with a sensitivity of 104dB and have an impedance of 16 ohms. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have six 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-9.

AFI-9SX

Outdoor loudspeaker shall be a high power full range two-way speaker utilizing two 12” Ferrofluid cooled, moisture stabilized neodymium woofers, two 6.5” moisture stabilized midrange drivers and a 2” exit, 4” diaphragm Ferrofluid cooled neodymium compression driver mounted to a large format 60-degree horizontal by 40-degree vertical non-resonant urethane horn. Mid and high frequencies shall be Point Source Coupled to the mid/high horn. The unit shall have a frequency response of 55Hz to 20kHz +/-3dB and a maximum long term SPL of 130dB with a sensitivity of 104dB and have an impedance of 16 ohms. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have six 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-9SX.

AFI-110

Subwoofer shall be a dual voice coil band pass type utilizing a 10” long excursion dual voice coil moisture stabilized driver. The unit shall have a frequency response of 48Hz to 145Hz +/-3dB and a maximum long term SPL of 114dB with a sensitivity of 93dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with two inputs on #8 barrier strips. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept third party articulating mounts and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-110.

AFI-110SX

Subwoofer shall be a dual voice coil band pass type utilizing a 10” long excursion dual voice coil moisture stabilized driver. The unit shall have a frequency response of 48Hz to 145Hz +/-3dB and a maximum long term SPL of 114dB with a sensitivity of 93dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with two inputs on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have two 3/8x16 steel backed rigging points, a bolt pattern on the rear panel to accept third party articulating mounts and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-110SX.

5/1/09

AFI-115

Subwoofer shall utilize a 15” moisture stabilized Ferrofluid cooled driver. The unit shall have a frequency response of 40Hz to 125Hz +/-3dB and a maximum long term SPL of 122dB with a sensitivity of 97dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-115.

AFI-115SX

Outdoor Subwoofer shall utilize a 15” moisture stabilized Ferrofluid cooled driver. The unit shall have a frequency response of 40Hz to 125Hz +/-3dB and a maximum long term SPL of 122dB with a sensitivity of 97dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grill shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-115SX.

AFI-118

Subwoofer shall utilize an 18” moisture stabilized Ferrofluid cooled driver. The unit shall have a frequency response of 35Hz to 70Hz +/-3dB and a maximum long term SPL of 125dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The speaker shall have fourteen 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-118.

AFI-118SX

Outdoor Subwoofer shall utilize an 18” moisture stabilized Ferrofluid cooled driver. The unit shall have a frequency response of 35Hz to 70Hz +/-3dB and a maximum long term SPL of 125dB with a sensitivity of 98dB. The loudspeaker shall be constructed using at least 13ply per inch void free birch plywood with an input and loop through on #8 barrier strips. The enclosure shall be coated in a highly durable and flexible UV stable exterior paint. The speaker grille shall be coated aluminum with a secondary fine mesh layer to repel water. The speakers input panel shall be housed inside a watertight ABS junction box. The speaker shall have fourteen 3/8x16 steel backed rigging points and two integral handles that cannot be used as fly points. The speaker shall be an Apogee Sound AFI-118SX.

Horizontal Yoke

Loudspeaker rigging shall come from the same manufacture as the loudspeaker and facilitate mounting a single speaker in a horizontal orientation to a wall, ceiling, beam or cable system. Loudspeaker and rigging assembly attachment to the building structure to be approved and stamped by an engineer licensed in the state where the installation is to occur.

Vertical Yoke

5/1/09

Loudspeaker rigging shall come from the same manufacture as the loudspeaker and facilitate mounting a single speaker in a vertical orientation to a wall, ceiling, beam or cable system. Loudspeaker and rigging assembly attachment to the building structure to be approved and stamped by an engineer licensed in the state where the installation is to occur.

Adjustable Rigging Beam

Loudspeaker rigging shall come from the same manufacture as the loudspeaker and facilitate suspending a pair of speakers in a vertical orientation. Rigging should allow for the splay angle between the loudspeakers to be adjustable. Loudspeaker and rigging assembly attachment to the building structure to be approved and stamped by an engineer licensed in the state were the instillation is to occur. Loudspeaker rigging shall be Apogee Sound Adjustable Rigging Beam

Tight Pack Rigging Plate

Loudspeaker rigging shall come from the same manufacture as the loudspeaker and facilitate suspending a single or multiple speakers vertically in a tight-pack configuration. Each rigging unit shall provide points for suspension and holes for bolting to adjoining loudspeakers. Loudspeaker and rigging assembly attachment to the building structure to be approved and stamped by an engineer licensed in the state were the installation is to occur. Loudspeaker rigging shall be Apogee Sound Tight Pack Rigging Plate

Third Party Articulating Mount

Loudspeaker rigging shall allow for articulation in both the vertical and horizontal planes. Rigging shall be sized appropriately for the weight of the loudspeaker and interface directly with the factory bolt pattern on the rear panel of the loudspeakers. Loudspeaker and rigging assembly attachment to the building structure to be approved and stamped by an engineer licensed in the state were the installation is to occur. Articulating rigging shall be Allen Products Multi Mount or OmniMount.

DLC24 DIGITAL LOUDSPEAKER CONTROLLER

Digital Signal Processor (DSP), Loudspeaker Controller/System, shall have 2 inputs capable of receiving analog or AES-EBU digital signals and 4 analog outputs. Unit shall contain factory presets for the loudspeakers employed and include active feedback type limiters. The unit shall have 13 bands of parametric equalization available per input put for system tuning and be controllable from a front panel serial DB9 RS-232 or rear panel RS-422 port. Digital Signal Processor (DSP), Loudspeaker Controller/System, shall be an Apogee Sound DLC24

AFI-MAINFRAME CONTROLER

The loudspeaker electronic processing unit shall be 1EIU rack space and be capable of receiving up to four analog signal processing cards. These cards shall have fixed equalization, crossovers, limiters and time alignment circuitry optimized for specific loudspeakers. Each card shall have a rear panel accessible trim pot style gain control and limiter threshold adjustment as well as a single limit indicator. The loudspeaker processor shall be an Apogee Sound AFI Main Frame Controller

CA-2000 STEREO POWER AMPLIFIER

The stereo power amplifier shall be 2EIU rack spaces and be capable of producing 250WRMS per channel into 4 ohms at 1kHz and 0.1% THD. The amplifier shall have level attenuators accessible from the rear panel only. The amplifier shall be cooled by variable speed fans drawing from the front of the unit and exhausting at the rear. The unit shall have an air filter on the front panel that is removable for

5/1/09

cleaning. Output stages shall be high speed switching MOSFETs with a linear power supply. The amplifier shall be an Apogee Sound CA-2000.

CA-4000 STEREO POWER AMPLIFIER

The stereo power amplifier shall be 2EIU rack spaces and be capable of producing 590WRMS per channel into 4 ohms at 1kHz and 0.1% THD. The amplifier shall have level attenuators accessible from the rear panel only. The amplifier shall be cooled by variable speed fans drawing from the front of the unit and exhausting at the rear. The unit shall have an air filter on the front panel that is removable for cleaning. Output stages shall be high speed switching MOSFETs with a linear power supply. The amplifier shall be an Apogee Sound CA-4000

CA-8000 STEREO POWER AMPLIFIER

The stereo power amplifier shall be 2EIU rack spaces and be capable of producing 880WRMS per channel into 4 ohms at 1kHz and 0.1% THD. The amplifier shall have level attenuators accessible from the rear panel only. The amplifier shall be cooled by variable speed fans drawing from the front of the unit and exhausting at the rear. The unit shall have an air filter on the front panel that is removable for cleaning. Output stages shall be high speed switching MOSFETs with a linear power supply. The amplifier shall be an Apogee Sound CA-8000

VMIX System Mixer

The mixer shall be an 8 channel rack mount mixer with 8 module bays capable of accepting advanced plug-in modules. Each channel shall have its own independent volume control, and LED signal/clip indicator. The mixer shall have a master volume control, bass and treble controls, and an 11-segment LED output level meter to monitor the output level of the mixer with Peak Hold meter switch. The mixer shall have an unbalanced output jack, a 125 Hz Lo-cut feature, tone control bypass switch (balanced transformer-isolated output), balanced output signal level switch (-50, -10, and +4 dBµ), resettable circuit breaker, power indicator, and grounded unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment. For larger applications, the mixer shall be able to bridge to another mixer using a built-in bridging jack and mute terminals, allowing the number of inputs to be increased. The mixer shall have a motorized volume control that can be remotely operated (with RVCP Remote Volume Control Panel). The mixer shall be rack mountable (with RPK87 rack mounting kit).

5/1/09