API 6A.pdf
Transcript of API 6A.pdf
-
A CameronIntroduction to AmericanPetroleum InstituteSpecificationsAPI 6A (ISO 10423):Specification for Wellhead and Christmas Tree Equipment
API Q1: Specification forQuality Programs, the APIMonogram Program and ISO-9000 Accreditations.
Cameron Locations
-
POLICY
The Cameron Division of Cooper Cameron Corporation supports the
development and use of international product standards such as those
published by API and ISO. These standards provide a common basis for
product characteristics and performance attributes and act to capture
the successful industry history associated with these products. Products
marketed, designed, manufactured and used in compliance with
recognized industry standards add significant value to our industry.
Cameron endorses the API monogram program and API Quality Program
Specification Q1. API Q1 applies the recognized benefits of the ISO 9001
Quality Program elements tailored specifically to the oil and gas industry.
The API monogram program joins the assessment of Quality programs
with the demonstrated ability to comply with international product
standards such as API Specification 6A (ISO 10423) for Wellhead and
Christmas Tree Equipment.
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
-
Specification for Wellhead andChristmas Tree Equipment
-
API SPECIFICATION 6A
API Specification 6A (ISO 10423) is the recognized industry standard for
Wellhead and Christmas Tree Equipment which was formulated to
provide for the availability of safe, dimensionally and functionally
interchangeable Wellhead and Christmas Tree Equipment. This
specification includes detailed requirements for the manufacture of
tubular suspension equipment, valves and fittings used at the location
of oil and gas wells to contain and control pressure and fluid flows.
Specification 6A also serves as the reference source for the design of
flanged end and outlet connections for use at 2,000 to 20,000 psi
maximum rated working pressures and a family of gate valves for use
over these same pressure ranges. API Specification 6A is also specified
as the base standard for
manufacture of subsea
equipment in accordance with
API Specification 17D.
The current edition of API 6A,
includes requirements for
Surface Safety Valves (SSV)
and Underwater Safety Valves
(USV).
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
EQUIPMENT
WellheadEquipment
Casing HeadHousing
Casing HeadSpools
Tubing HeadSpools
CrossoverSpools
MultistageHead Housing
& Spools
CrossoverConnectors
Tubing HeadAdapters
Top Connectors
Tees andCrosses
Fluid SamplingDevices
Adapter andSpacer Spools
Other EndConnectors(Proprietary)
MandrelHangers
Slip Hangers
SingleCompletion
Valves
MultipleCompletion
Valves
Actuated Valves
Valves Preparedfor Actuators
Check Valves
Chokes
SSV/USV &Actuators for
Offshore Services
Weld NeckConnectors
BlindConnectors
ThreadedConnectors
Adapter andSpacer
Connectors
Actuators
Ring Gaskets
Bull PlugsRunning Tools
Valve Removal PlugsWear Bushings
Connectors andFittings
Casing & TubingHangers
Valves andChokes
LooseConnectors
OtherEquipment
API Specification 6A (ISO 10423) covers Wellhead and Christmas TreeEquipment as follows:
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
PRODUCT SPECIFICATION LEVELS (PSLs)
API Specification 6A (ISO 10423) provides definition of standard service
conditions and introduces the concept of product specification levels
(PSLs) which will be referred to throughout the document. The PSLs
define different levels of effort, or levels of technical requirements
which may be specified for a product. Generally, these levels represent
industry practice for various service conditions. The decision tree shown
below is designed to assist the purchaser in selecting the proper
specification levels (PSLs) for primary parts of Wellhead and Christmas
Tree Equipment.
START HERE
YES YES
YES
NONO
NO
YES YES YES
NO NO
NO
NO
YES
YES
NO
PSL-3G
PSL-3G
PSL-3
PSL-3G
PSL-3
PSL-2
PSL-3
PSL-2
PSL-2
PSL-3
PSL-2
PSL-1
PSL-1
RATED WORKINGPRESSURE 103.5MPa (15,000 PSI)
HIGH H2S
CONCENTRATION ?
GAS WELL
NACE ?HIGH H2S
CONCENTRATION ?RATED WORKING
PRESSUREGAS WELL
RATED WORKINGPRESSURE
GAS WELL
RATED WORKINGPRESSURE
RATED WORKINGPRESSURE
GAS WELL
> 34.5 MPa (5,000 PSI )
34.5 MPa (5,000 PSI )
> 34.5 MPa (5,000 PSI)
34.5 MPa (5,000 PSI)
> 34.5 MPa (5,000 PSI)
34.5 MPa (5,000 PSI)
34.5 MPa (5,000 PSI)
> 34.5 MPa (5,000 PSI)
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
PRESSURE RATINGS
TEMPERATURE CLASSES
Six pressure ratings from 2,000 to 20,000 psi represent the maximumworking pressure of the equipment.
API Pressure Rating in PSI
2,000 13.8
3,000 20.7
5,000 34.5
10,000 69.0
15,000 103.5
20,000 138.0
API Pressure Rating in MPa
Eight Temperature Classes, each of which represent a range oftemperatures from the minimum ambient air temperature to themaximum temperature of the well fluid passing through or contained by the equipment.
API TEMP. CLASSIFICATION
OPERATING RANGE(DEG. F)
(MIN.) (MAX.)
OPERATING RANGE(DEG. C)
(MIN.) (MAX.)
K -75 TO 180
-50 TO 180
-20 TO 180
ROOM TEMPERATURE
0 TO 150
0 TO 180
0 TO 250
35 TO 250
-60 TO 82
-46 TO 82
-29 TO 82
ROOM TEMPERATURE
-18 TO 66
-18 TO 82
-18 TO 121
2 TO 121
L
P
R
S
T
U
V
Note: These temperature classes can be used in combination with one another to achieve a wider rating. Forinstance, a common rating for 6A gate valves is P+U (-20 to 250 F).
-
Corrosion Resistant Alloyb
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
MATERIAL CLASSES
There are seven Material Classes which specify minimum materialrequirements for general or sour service shown below. API 6A (ISO 10423) equipment must be designed, tested and marked assatisfactory for one of these Material Classes.
Minimum Material Requirements
API Material ClassBody, Bonnet, End & Outlet
ConnectionsPressure Controlling Parts,Stems, & Mandrel Hangers
AA - General Service Carbon or low alloy steel
Carbon or low alloy steel
Stainless Steel
Carbon or low alloy steelb
Carbon or low alloy steelb
Stainless steelb
Corrosion Resistant Alloyb
Carbon or low alloy steel
Stainless steel
Stainless Steel
Carbon or low alloy steelb
Stainless steelb
Stainless steelb
BB - General Service
CC - General Service
DD - Sour Servicea
EE - Sour Servicea
FF - Sour Servicea
HH - Sour Servicea
aAs defined by National Association of Corrosion Engineers (NACE) Standard MR0175bIn compliance with NACE Standard MR0175Only the most stringent classification is marked.
ANNEX F TESTINGPerformance verification testing is often performed on prototypes orproduction models of API Specification 6A (ISO 10423) equipment toensure that the performance requirements (PRs) specified for pressure,temperature, load, mechanical cycles, and standard test fluids are met in the design of the product.
Performance Verification Testing may include:Pressure/Temperature CyclesLoad/Mechanical CyclesNonmetallic Seal Thermochemical Testing
Scalable Performance Verification levels (i.e. PR1, PR2) are applicable tomany API 6A products. Although Annex F Testing is not a requirement inAPI 6A, Cameron is proud to offer a wide variety of products proven tomeet, and often exceed the performance verification requirements of API 6A Annex F.
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
WELDING
Quality control requirements for welding generally increase as the PSLlevel increases from 1 through 3 with each level building on the levelbelow it. No welding is permitted on PSL-4 equipment except for corrosion resistant alloy overlays. The following table applies topressure containing fabrication and repair weldments for bodies,bonnets, and end and outlet connections:
Weld ProcedureQualification
WelderPerformanceQualification
WeldingConsumables,
InstrumentCalibration
Visual Exam ofWeld
Weld Surface NDE: PT/MT
Weld VolumetricNDE: UT/RT
Weld HardnessTesting
ASME SECT. IXWith
Hardness Survey
ASME SECT. IX
DocumentedControlsRequired
_
_
_
_
Same as PSL-1 plusBase MetalGrouping
Same as PSL-1 plusHole Qualification
Same as PSL-1
Required
Required
Required For AllFabrication Welds and Repair Welds
>25% of Wall
Required For AllFabrication Welds and Repair Welds
>20% of Wall
_
Same as PSL-2 plusChemical Analysis
and PWHT Controls
Same as PSL-2
Same as PSL-1
Required
Required
Required
No Welding AllowedExcept for
Corrosion Resistant Alloy Overlays
No Welding AllowedExcept for
Corrosion Resistant Alloy Overlays
PSL-1 PSL-2 PSL-3 PSL-4
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
QUALITY CONTROL
Specification 6A (ISO 10423) describes pertinent information oninspections, tests, examinations, and required documentation. Since theselection of Product Specification Level (PSL) is ultimately a purchasersdecision, quality control information is provided to make it easy for usersto select the PSL level consistent with their risk management needs.
Quality Control Requirements for Equipment
Requirements
Drift Test Yes Yes Yes Yes
Hydrostatic Test Yes Yes Yes, Extended Yes, Extended
Gas Test _ _ Yes
AssemblyTraceability _ _ Yes Yes
Serialization _ Yes Yes Yes
PSL-1 PSL-2 PSL-3 PSL-4
Yes
Yes, Extended
Yes
Yes
Yes
PSL-3G
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
QUALITY CONTROL
Quality Control Requirements for Bodies, Bonnets, and End andOutlet Connections
Requirements
Tensile Testing Yes Yes Yes Yes
Impact Testing K, L K, L, P Yes Yes
Hardness Testing Sampling Single Multiple Multiple
DimensionalVerification Sampling Sampling Yes Yes
Traceability _ Yes Yes Yes
PSL-1 PSL-2 PSL-3 PSL-4
Chemical Analysis _ Yes Yes Yes
Visual Examination Yes Yes _ _
Surface NDE _ Yes Yes Yes
Weld NDE _ Yes Yes Yes
Serialization _ _ Yes Yes
Volumetric NDE _ _ Yes Yes
Definitions:
End and Outlet Connections - Integral threads, male or female; flanges, studded or through-bolted; or anyother means used to join together equipment that contains or controls pressure.
Body - Any portion of API Spec 6A equipment between end connections, with or without internal parts,which contains well-bore pressure.
Bonnet - A pressure-containing closure for a body, other than an API end or outlet connection.
-
MARKINGS
Section 8 of Specification 6A and the chart below describemarking instructions for equipment. The marking requirementsinclude the following:
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
CC-OKC API 135/8" 5000 PSI S AA 1 PR2 6-01
ManufacturersMark
Monogram
NominalSize
Rated WorkingPressure
TemperatureClass
MaterialClass
ProductSpecification
Level
PerformanceRequirement
Level
Date of FinalAcceptance
-
HOW TO ORDER
The following data sheet is included as a worksheet for assemblinginformation needed to place an order:
Well name(s) and location(s): __________________________________________________________________Maximum operating pressure: __________________________________________________________________Anticipated wellhead shut-in pressure: __________________________________________________________Temperature ranges anticipated: ________________________________________________________________Minimum ambient temperature: ________________________________________________________________Maximum flowing fluid temperature at wellhead: ________________________________________________Anticipated composition of produced fluids: CO2 __________ ppm ___________ Chlorides ________ppm___________________________H2S ______________ppm ______________ Other ______________
Anticipated completion or future workover or recovery operations which would affect pressure,temperature, or fluid content __________________________________________________________________New values:_________________________________________________________________________________Are there any government regulations that will apply or must be met by this equipment?_______________If so, which one(s)? __________________________________________________________________________Water or brine pH: Does NACE MR0175 apply?Will scale, paraffin, corrosion, or other types of inhibitors be used? __________________________________Inhibitor type: _______________ Inhibitor carrier: _______________ Batch or continuous inhibition? ______Will acidizing be performed? ________________________________ Type of acid: ______________________Anticipated production rates: ______________________ M3/D oil/condensate
______________________ M3/D gas______________________ M3/D S&W
Will erosion be concern? ____________________ Cause: __________________________________________External coating? Yes, Type _________________________ No _________________Internal coating? Yes, Type__________________________No _________________Delivery requirements: ____________________________________________________________________________________________________________________________________________________________________Special shipping, packing and storage instructions: ________________________________________________
Casing Program
Top Joint String
Size (OD) Wt., Kg/m (lb/ft) Grade Connection Total String Bit SizeHanging Wt. in mmin DaN (lbs) (in)
Conductor ________ ________ ________ ________ ________ ________Surface Csg. ________ ________ ________ ________ ________ ________Protective Csg ________ ________ ________ ________ ________ ________Production Csg. ________ ________ ________ ________ ________ ________Tubing ________ ________ ________ ________ ________ ________
Type of Completion: single or multiple: ________________
Technical contact in buyers organization: ________________________________________________________Phone: ________________________________________________________
For more information, contact your local Cameron representative.Cameron, P.O. Box 1212 Houston, TX 77251-1212 Tel: (713)939-2211 FAX: (713) 939-2620http://www.camerondiv.com
EXHIBIT A1 GENERAL WELLHEAD EQUIPMENT DATA SHEET
-
API Q1: Specification for Quality Programs, the APIMonogram Program and ISO-9000 Accreditations.
SO9000 A
ccredtat
on
s.
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
API SPECIFICATION Q1
OVERVIEWAPI Q1 is intended to be used in conjunction with international oil and gasproduct standards by internationally licensed manufacturers. Used in thismanner, API Q1 delivers significant value to the industry by providing acohesive link between the accreditation of a manufacturers quality systemwith their ability to provide products meeting industry and customerrequirements.
API Specification Q1 differs from generic quality systems, (e.g., ISO 9000Series), by its role in the voluntary licensing of manufacturers to provide oiland gas industry products in accordance with API specifications. API licensesare only issued after an on-site survey has confirmed that the licensee adheresto the requirements of both the quality system standard API Q1 and therequirements of an international oil and gas product specification recognizedby the oil and gas industry and API. In contrast, generic quality systemrequirements are normally intended to be applied to any industry or productthrough contractual agreements with or without industry standards orspecifications.
Typical Quality Program Elements (API Q1)1 SCOPE 2 REFERENCES3 DEFINITIONS4 QUALITY SYSTEM REQUIREMENTS4.1 MANAGEMENT RESPONSIBILITY4.2 QUALITY SYSTEM4.3 ORDER REVIEW4.4 DESIGN CONTROL4.5 DOCUMENT AND DATA CONTROL4.6 PURCHASING4.7 PURCHASER-SUPPLIED PRODUCT4.8 MATERIAL/PRODUCT
IDENTIFICATION AND TRACEABILITY4.9 PROCESS CONTROL4.10 INSPECTION AND TESTING
Typical Quality Program Elements (ISO 9001 2000)1 SCOPE 2 NORMAL REFERENCES3 TERMS AND DEFINITIONS4 QUALITY SYSTEM REQUIREMENTS5 MANAGEMENT RESPONSIBILITY6 RESOURCE MANAGEMENT7 PRODUCT REALIZATION8 MEASUREMENT, ANALYSIS AND IMPROVEMENT
4.11 INSPECTION, MEASURING, AND TEST EQUIPMENT
4.12 INSPECTION AND TEST STATUS4.13 CONTROL OF NONCONFORMING
PRODUCT4.14 CORRECTIVE ACTION4.15 HANDLING, CLEANING, STORAGE,
PACKAGING, AND DELIVERY4.16 QUALITY RECORDS4.17 INTERNAL QUALITY AUDITS4.18 TRAINING, INDOCTRINATION,
AND QUALIFICATION4.19 SERVICING4.20 STATISTICAL TECHNIQUES
-
CAMERON, P.O, Box 1212, Houston TX, 77251-1212, Tel: 713.939.2211 Fax: 713.939.2620, http://www.camerondiv.com
Cameron is proud to maintain API and ISO accreditations at our manufac-turing and repair facilities. In fact, Cameron holds the largest number of APIlicenses in the industry. These accreditations, however, only make up a partof Camerons commitment to quality. We invite you to contact your localCameron representative and review our commitment to quality in detail.
API and ISO ACCREDITATIONS
API 6A API 6D API 16A API 16C API 16R API 17DPlant Wellhead & Ball Drill Through Drilling API 16D Marine Subsea ISO
Locations Xmas Trees Valves Equipment Chokes Controls Drilling Riser EquipmentCouplings
Western HemisphereBrookshire 0126 ISO 9001Edmonton (CC) 0418.5 0086.3 ISO 9001Edmonton (CCV) 0244.5HoustonActuators 0506 0014 0022 ISO 9001HoustonControls 0012 0015 ISO 9001Liberty 0418 0244 0086 0001 0028 ISO 9001Little Rock 0073 ISO 9001Livingston, TX 0276Maracaibo (CC) 0042.27 0086.9 ISO 9002Oklahoma City (CCV) 0418.2 0244.2 ISO 9001Oklahoma City (CC) 0418.13 0244.10 ISO 9001Patterson 0418.3 0244.3 0086.1 0006.1 0007.1 ISO 9001Sao Paulo ISO 9001Veracruz 0148.8 0121.8 ISO 9001Ville Platte 0244.4 ISO 9001Zarate 0418.7 0244.7 0086.5 ISO 9001
Eastern HemisphereAberdeen ISO 9001Beziers 00418.9 00244.8 0086.6 0006 0007.4 ISO 9001Celle 00418.19 0086.8 0006 0007.6 ISO 9001Hoogezand ISO 9002Leeds 0418.10 0086.7 0007.5 ISO 9001Livingston, Scotland 0291 ISO 9001Longford 00418.20 0007.7 ISO 9001Randaberg, Norway 0418.22 ISO 9001
Asia Pacific / Middle EastBatam 0223 0000 ISO 9002Darul, Malaysia 0418.12 0244.9 0007.8 ISO 9002Deer Park, VictoriaAustralia 0042.18 0014.9 0001.6 ISO 9001
Oman 0516 ISO 9002
Singapore 0418.6 0244.6 0086.4 0007.3 ISO 9001
-
CAMERON LOCATIONS
-
LOCATIONS
DOMESTICAlaska600 East 57th PlaceAnchorage, Alaska 99518-5761Phone: (907) 562-2332Fax: (907) 562-3880
California3004 Jewett Ave.Bakersfield, California 93301(P.O. Box 3545, Bakersfield, CA 93385)Phone: (661) 323-8183Fax: (661) 323-0946
418 Baylor DriveWoodland, California 95695Phone: (530) 668-8069Fax: (530) 688-0948
Colorado1660 Lincoln, Suite 2950Denver, Colorado 80264Phone: (303) 861-1850Fax: (303) 861-1868
710 23-1/4 RoadGrand Junction, Colorado 81505Phone: (970) 241-5711Fax: (970) 241-5730
LouisianaHighway 182Berwick, Louisiana 70342(P.O. Box 457, Berwick, LA 70392)Phone: (985) 395-6171Fax: (985) 395-1257
650 Poydras St.Poydras Center, Suite 2310New Orleans, Louisiana 70130Phone: (504) 529-7634Fax: (504) 522-8837
Highway 90 EastPatterson, Louisiana 70392(P.O. Box 457, Patterson, LA 70392)Phone: (985) 395-6171Fax: (985) 395-1257
10361 MeadowviewKeithville, Louisiana 71047(P.O. Box 18978, Shreveport, LA 71138)Phone: (318) 925-6200Fax: (318) 925-5040
Mississippi1020 Hillcrest DriveLaurel, Mississippi 39440(P.O. Box 3039, Laurel, MS 39442)Phone: (601) 649-8900Fax: (601) 649-8909
New Mexico503 South Behrend Ave.Farmington, New Mexico 84701Phone: (505) 327-3402Fax: (505) 327-0454
500 North LeechHobbs, New Mexico 88240Phone: (505) 397-1325Fax: (505) 393-5957
Oklahoma4341 S.W. 33rd StreetOklahoma City, Oklahoma 73119Phone: (405) 682-1661Fax: (405) 682-1051
7500 S.W. 29th StreetOklahoma City, Oklahoma 73179(P.O. Box 75308, Oklahoma City, OK 73147)Phone: (405) 745-2715Fax: (405) 745-4071
Texas6441 I.H. 37Corpus Christi, Texas 78409Phone: (361) 289-1455Fax: (361) 289-6251
1600 Pacific Place, Suite 1575Dallas, Texas 75201Phone: (214) 855-7823Fax: (214) 855-0033
13013 Northwest FreewayHouston, Texas 77040(P.O. Box 1212, Houston, TX 77251-1212)Phone: (713) 939-2211Fax: (713) 939-2620
6650 Bingle RoadHouston, Texas 77092(P.O. Box 1212, Houston, TX 77251-1212)Phone: (713) 683-4600Fax: (713) 683-4729
6750 Bingle RoadHouston, Texas 77092(P.O. Box 1212, Houston, TX 77251-1212)Phone: (713) 369-4100Fax: (713) 369-4128
9220 Taub RoadHouston, Texas 77064(P.O. Box 1212, Houston, TX 77251-1212)Tel: (281) 897-8500Fax: (281) 897-8789
10810 NW FreewayHouston, TX 77092(P.O. Box 1212, Houston, TX 77251-1212)Phone: 713-354-1200Fax: 713-354-1255
29501 Katy FreewayKaty, Texas 77494Phone: (281) 391-4600Fax: (281) 391-4640
Highway 90 @ FM 1909Liberty, Texas 77575(P.O. Box 10286, Liberty, TX 77575)Phone: (936) 336-8811Fax: (936) 336-2822
-
LOCATIONS
2705 E. Marshall Ave.Longview, Texas 75602(P.O. Box 1311, Longview, TX 75606)Phone: (903) 236-4884Fax: (903) 234-0336
306 W. Wall, Suite 1310Midland, Texas 79702Phone: (915) 682-4688Fax: (915) 682-4692
270 S. GrandviewOdessa, Texas 79761Phone: (915) 337-5475Fax: (915) 337-3001
Utah1442 E. Highway 40Vernal, Utah 84078(P.O. Box 492, Vernal, UT 84078)Phone: (435) 781-0434Fax: (435) 789-5656
Wyoming7048 Zero RoadCasper, Wyoming 82604(P.O. Box 2229, Casper, WY 82644)Phone: (307) 472-0222Fax: (307) 265-1318
102 Foothill Blvd.Rock Springs, Wyoming 82901Phone: (307) 382-3134Fax: (307) 382-3190
InternationalALGERIAZone IndustrielleIntersection rue Desserte #10Hassi Messaoud, AlgeriaTel: 213-9-73-91Fax: 213-9-73-74-27
ANGOLARua Major Kanhanguio No. 90Luanda Republic of AngolaPhone: 244-2-33-13-19Fax: 244-2-39-04-36
ARGENTINAMaipu 971, Piso 1 DTO D1006 Buenos Aires, ArgentinaPhone: 54-11-4-314-5520Fax: 54-11-4-311-2838
Av. Antartida Argentina 27112800 Zarate, ArgentinaPhone: 54-3487-422297Fax: 54-3487-423404
AUSTRALIALot 1702 McKinnon RoadBerrimah Northern Territory0828 DarwinPhone: 61-8-8931-2034Fax: 61-8-8931-2036
Lot 1 Ballarate Road Deer Park VicSt. Albans 3021Victoria, Australia(P.O. Box 789)Phone: 61-3-9361-4444Fax: 61-3-9361-4400
45-47 Colin StreetWest Perth, 6005Western Australia(P.O. Box 94, West Perth 6872)Phone: 61-08-9226-1444Fax: 61-08-9226-1555
BAKU37 Boyuk Gala StreetOld CityBaku 370004AzerbaijonPhone: 994-12-974606Fax: 994-12-974616
BRAZILRod Amaral Peiscoto, KM 164,5ImboassicaMaCae, Rio De Janeiro, BrazilCEP 27920-340Phone: 55-24-773-6331Fax: 55-24-773-6322
Av. Rio Branco, 181-Sala 801Rio de Janeiro RJ20040 - 007 BrazilTel: 55-21-533-4032Fax: 55-21-524-5051
Avendia Paulista, 2.421-JardinsSao Paulo - S.P. - BrazilCEP 01311-300Phone: 55-11-3066-3600Fax: 55-11-3064-6228
Av. Arcenio Riemma1451 - Bairro do UnaCEP 120300-000Taubate - Sao Paulo BrazilPhone: 55-12-210-1000Fax: 55-12-218-2319
BRUNEILot 4007, Kawasan G22Simpang 17Seria, Brunei Darussalam(P.O. Box 177, Kuala Belait 6001)Phone: 673-3-222-613Fax: 673-3-224-284
CANADA420 Aquaduct DriveBrooks, Alberta T1R 1C4(Box 1501)Phone: 403-793-2700Fax: 403-793-2200
Texas (continued)
-
LOCATIONS
855 42nd Avenue SEBuilding BCalgary, Alberta T2P 2X6Phone: 403-261-2800Fax: 403-262-5181
5003 93rd StreetEdmonton, Alberta T6E 5S9Phone: 780-434-3476Fax: 780-437-7397
259A Tundra RoadFort St. John, British Columbia V1J 4H6(P.O. Box 6075)Phone: 250-785-2700Fax: 250-785-0700
4904 48th AvenueFort Nelson, British Columbia, V0C1R0Phone: 250-774-7394Fax: 250-774-7392
11302 89th AvenueGrand Prairie, Alberta T8V 5V8Phone: 780-539-2333Fax: 780-532-0770
67 Atlantic StreetDarmouth, Nova Scotia B2Y 4P4Phone: 902-461-4444Fax: 902-461-0493
#9, 4830 78th StreetRed Deer, Alberta T4P 2B3Phone: 780-342-2700Fax: 780-340-0700
CHILEBalfer LTDAZona FrancaP. O. Box 117-DPunta Arenas, ChilePhone: 56-61-213931Fax: 56-61-214379
CONGO45 Rue Louis Blanc92400 CourbevoieFrance(92038 Paris-La-Defense Cedex Mail)Phone: 242-945563Fax: 242-940283
EGYPTVilla el BarakaNo. 8 Road 279New MaadiCairo, Egypt A.R.EPhone: 202-516-4463Fax: 202-516-4789
FRANCEPlaine Saint-Pierre,34535 Beziers Cedex FrancePhone: 33-467-111500Fax: 33-467-111600
15 Avenue du General de Gaulle64000 Pau FrancePhone: 33-559-807640Fax: 33-559-807649
45 Rue Louis Blanc92400 Courbevoie, France(92038 Paris-La-Defense Cedex Mail)Phone: 33-1471-76059Fax: 33-1471-76099
GABONB. P. No. 869Port GentilRepublique GabonaisePhone: 241-553-026Fax: 241-555-897
GERMANYLueckenweg 129227 Celle, Germany(P.O. Box 3225)Phone: 49-5141-8060Fax: 49-5141-806333
INDONESIAc/o P. T. ImecoJalan Ampera Raya No. 9 & 10Cilandak TimurJakarta #12550, IndonesiaPhone: 62-21-780-4125Fax: 62-21-782-2428
PT Kartic Yasa SaranaJL Tenggiri Kav 21Batu AmparBatam, IndonesiaPhone: 778-412-285Fax: 778-412-284
IRELANDAghafad, LongfordRepublic of IrelandPhone: 353-43-50600Fax: 353-43-41560
KAZAKHSTAN80 Maresyer StreetBuilding 2, Apt 25, 41KazakhstanPhone: 7-3132-540-615Fax: 7-3132-542-519
MALAYSIA2MC, Asian Supply BaseRanca Ranca Industrial EstateLubuan Federal TerritoryMalaysiaPhone: 60-87-413914Fax: 60-87-415921
Lot 1431Piasall Jaya Industrial Estate98000 Miri SarawakEast MalaysiaPhone: 60-85-657335Fax: 60-85-656335
-
LOCATIONS
Lot 58, Jalan Utas 15/7,Kawasan PerusahaanSection 15, 40200 Shah AlamSelangor, Malaysia(P.O. Box 7170, 40707 Shah Alam)Phone: 60-3-5510-8850Fax: 60-3-5510-4772
Warehouse 5, Door 7AKemaman Supply Base24007 KemamanTerengganu, MalaysiaPhone: 60-9-863-1145Fax: 60-9-863-1410
MEXICOCalle 37 No. 147-ACol. Hector Perez Martinez24100, C.D. Del Carmen CampMexicoPhone: 52-938-27924Fax: 52-938-27924
Avendia Homero 1804, Suite 403Col. Chapultepec Morales11510 Mexico D.F., MexicoPhone: 52-5-5800296Fax: 52-5-3958869
Av. Acacias Esq, Av. Ciruelos S/NCd. Ind. Bruno PagliaiVeracruz, VerMexico, C.P. 91697(P.O. Box MEB-MX17-390)Phone: 52-29-891700Fax: 52-29-891701
Av. Paseo Tabasco No. 417Col. MunicipalVillahermosa, TabascoMexico, C.P. 86090Phone: 52-93-141755Fax: 52-93-141755
Carretera a Monterey, KM 104Reynosa, TamaulipasMexicoPhone: 52-89-297410Fax: 52-89-247420
NEW ZEALANDP. O. Box 672Papakura, AucklandNew ZealandPhone: 64-9-299-8103Fax: 64-9-299-8103
NIGERIA18B Thompson AvenueIkoyi, Lagos, NigeriaPhone: 2341-269-4003Fax: 2341-269-4003
Plot 45 Trans Amadi Ind. LayoutP.M.B. 995Port Harcourt, NigeriaPhone: 234-84-236761Fax: 234-84-238742
Ogunu RoadP.M.B. 1066Warri, NigeriaPhone: 871-53-230-512 or 473Fax: 871-53-230-512
THE NETHERLANDSSweelinckplein 112517GKThe Hague, The NetherlandsPhone: 31-70-365-7904Fax: 31-70-364-5941
Produktieweg 149601 MAHoogezand, The Netherlands(P. O. Box 121, 9600 AC)Phone: 31-598-361900Fax: 31-598-396298
NORWAYP. O. Box 665346 AgotnesBergen, NorwayPhone: 47-56-322811Fax: 47-56-334593
Mekjarvik 14070 RandabergStavanger, NorwayPhone: 47-51-415000Fax: 47-51-418160
OMANRoad 15Rusayl Industrial EstateSultanate of Oman(P.O. Box 130, Postal Code 124)Phone: 968-629156Fax: 968-626923
GBM Building Level AAl Wallaj Street QurumMuscat, Sultanate of Oman(P.O. Box 985, Postal Code 112)Phone: 968-562158Fax: 968-562178
PAKISTANNo 12, Street 12F-7/2(P. O. Box 1416)Islamabad PakistanPhone: 92-51-274952Fax: 92-51-824141
QATARc/o Al Ahed Trading and Const. Co. Ltd.P. O. Box 3266Doha, QatarPhone: 974-410797 or 835Fax: 974-411582
-
LOCATIONS
RUSSIAPer. Sadovskikh, 4Apt. 12Moscow 103001, RussiaPhone: 7-502-2213422Fax: 7-502-2213010
SAUDI ARABIAAl Khobar 31952Saudi Arabia(P. O. Box 31684)Phone: 966-3-893-3333, ext 399Fax: 966-3-894-6426SCOTLANDBadentoy AvenuePortlethenAberdeenshire, Scotland AB1 4YBPhone: 44-1224-282000Fax: 44-1224-781800
ICS House Badentoy ParkPortlethenAberdeenshire, Scotland AB1 4YAPhone: 44-1224-783500Fax: 44-1224-783355
SINGAPORENo.2 Gul CircleJurong Industrial EstateSingapore 629560Phone: 65-861-3355Fax: 65-861-6197
THAILANDC-O Level 23, CP Tower313 Silom Road, BangrukBangkok 01500ThailandPhone: 66-2-231-8320Fax: 66-2-231-8321
UNITED ARAB EMIRATESc/o Sigma Enterprises BldgMussafah Area, 7th StreetP.O. Box 3555Abu Dhabi, U.A.EPhone: 971-2-551-1313Fax: 971-2-551-0441
P.O. Box 43966Abu Dhabi, U.A.E.Phone: 971-2-723648Fax: 971-2-782293
UNITED KINGDOMUnits 1 & 2 Boundary RoadHarfreys Industrial EstateGreat Yarmouth, NorfolkEngland NR31 OLYTel: 44-1493-440438Fax: 44-1493-655405
Unit 11, Brinell WayHarfreys Industrial EstateGreat Yarmouth, NorfolkEngland NR31 OLUPhone: 44-1493-650675Fax: 44-1493-650676
Queen StreetStourtonLeeds, West YorkshireEngland LS10 1SBPhone: 44-113-2701144Fax: 44-113-2764751
5 Mondial WayHarlingtonHayes UB3 5ARLondon, EnglandPhone: 44-280-9901800Fax: 44-181-9901888
VENEZUELACarretera A. Perija KM 7 1/2Calle 166, No. 49 F-180Barrio el SilencioMaracaibo, Venezuela 4001-APhone: 58-261-7312-960Fax: 58-261-7310-638
Zona Industrial de MaturinManzana 49, Calle 2Detras de VicsonMaturin, Monagas, VenezuelaPhone: 58-291-6526-412Fax: 58-291-6516-946
Av. Venezuela, 3er Piso, Oficina 316Torre AmericaBello MonteCaracas, VenezuelaPhone: 58-212-707-6403 or 6404Fax: 58-212-762-1379
Urb. Canaima, Calle F, Casa 29-FPunta de Mata, Monagas, VenezuelaPhone: 58-292-2370-014Fax: 58-292-3370-429
Av. Intercimunal, Carrera HAL. Lado dek Rio TammareSector el PradoTia Juana, edo Zulia, VenezuelaPhone: 58-65-310-521Fax: 58-65-310-832
-
Western HemisphereCameronPO Box 1212Houston, Texas 77251-1212Tel 713 939 2211Fax 713 939 2620
Cameron WIllisTel: 713 354 1200Fax: 713 354 1291
Cameron ControlsTel: 713 683 4600Fax: 713 683 4729
Cameron DrillingTel: 713 939 2211Fax: 713 939 2620
CAMSERVTel: 713 939 2211Fax: 713 939 2620
Eastern HemisphereCooper Cameron (U.K.) Ltd.5 Mondial WayHarlingtonHayes, UB3 5AREnglandTel 44 208 990 1800Fax 44 208 990 1888
Asia Pacific/Middle EastCooper Cameron (Singapore) Pte, Ltd.Subsidiary of Cooper Cameron Corporation2 Gul Circle, Jurong Industrial EstSingapore 629560Republic of SingaporeTel 65 861 3355Fax 65 861 6197
Visit our website at: www.camerondiv.com
Cooper Cameron Corporation, Cameron Division, Printed in USA, 7/01, NP/3M, WR10383 / TC1253