Ansys Mechanical APDL lecture 3 by Haydar Alsalami from IRAQ - Hilla, studied in JNTUH - INDIA .
Ansys Mechanical APDL lecture 1 by Haydar Alsalami from IRAQ - Hilla, studied in JNTUH - INDIA ....
description
Transcript of Ansys Mechanical APDL lecture 1 by Haydar Alsalami from IRAQ - Hilla, studied in JNTUH - INDIA ....
1 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Link:
2 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Preprocessor:
Choosing structural to
update all mechanical
and physical properties
such as Loads, stresses ..
etc.
3 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Choosing 2D if
available for easy
solution, if not choose
3D
4 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Seeing type of element
we already choose it.
Enter number 1 then enter
first area below then
Apply. Enter number 2
then enter second area then
OK. But we have to setup
MESH according to these
two areas as we will see.
5 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
e: means exponential
2e5: means 200000
PRXY : start from 0
and less than 1, here
take it 0
6 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Entering key points : x,y,z
Press apply after each key
point, then press ok after
last one.
7 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
8 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
This is very important step,
because we have got two
areas, then we have to
setup MESH as follows
Since we picked first link,
we must choose number 1
here, (number 1 already
appears), then Apply.
9 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
For second area, we must
choose number 2 then OK.
(Do same procedure if
there are many areas.)
10 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
For Link and Pipe only we
must enter number ( 1 ) this is
compulsory, and then ok, but
for another types of elements
we can enter any number.
11 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It will be like this
12 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
13 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It will be like this
14 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Solution:
Choosing All DOF to
constraint all directions
along x,y,z or you can
choose constraint along
any direction ux or uy
or uz.
15 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It should look like this
16 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Write negative
magnitude to reverse
the direction of FY
downward.
17 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It will be like this
18 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
19 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
General-postprocessor:
20 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It should appear like this
21 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
For animation the
model press here.
22 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
There will be
animation.
You can change this
slide to make animation
faster or slower
Click here
if you want
stop the
animation,
then close.
23 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Find Results:
We must enter here
number 1 .
We choose last choice
By sequence num
SMSC relate to find LOAD
distribution on.
24 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
v
We must enter here
number 1 .
We choose last choice
By sequence num
LS relate to find STRESS
distribution .
25 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
We must enter here
number 1
We choose last choice
By sequence num
LEPEL relate to find
STRAIN distribution
26 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It should be like these.
27 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
We choose SMS1 for
load distribution .
28 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
We choose LS1 for Stress
distribution .
We can repeat this step for
STRAIN
29 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
We can choose only one
type of results or more by
click left cursor one by
one, then OK.
30 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Change the shape to real style:
First step back to primary
deformation.
31 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
It will be like this
32 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
33 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
Choosing Multi-Plots
Will change the
drawing to real style.
34 Haydar Alsalami \ JNTUH \ India mobile: 00919059070644 – Iraq mobile: 009647801518389 E-Mail: [email protected]
We can apply
deformation on real
style and animation
too.