Ansys mechanical apdl context sensitive help

download Ansys mechanical apdl context sensitive help

of 218

  • date post

    12-Aug-2015
  • Category

    Education

  • view

    377
  • download

    6

Embed Size (px)

Transcript of Ansys mechanical apdl context sensitive help

  1. 1. Mechanical APDL Context Sensitive Help Release 15.0ANSYS,Inc. November 2013Southpointe 275 Technology Drive Canonsburg,PA 15317 ANSYS,Inc.is certified to ISO 9001:2008. ansysinfo@ansys.com http://www.ansys.com (T) 724-746-3304 (F) 724-514-9494
  2. 2. Copyright and Trademark Information 2013 SAS IP, Inc. All rights reserved. Unauthorized use, distribution or duplication is prohibited. ANSYS, ANSYS Workbench, Ansoft, AUTODYN, EKM, Engineering Knowledge Manager, CFX, FLUENT, HFSS and any and all ANSYS, Inc. brand, product, service and feature names, logos and slogans are registered trademarks or trademarks of ANSYS, Inc. or its subsidiaries in the United States or other countries. ICEM CFD is a trademark used by ANSYS, Inc. under license. CFX is a trademark of Sony Corporation in Japan. All other brand, product, service and feature names or trademarks are the property of their respective owners. Disclaimer Notice THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION INCLUDE TRADE SECRETS AND ARE CONFID- ENTIAL AND PROPRIETARY PRODUCTS OF ANSYS, INC., ITS SUBSIDIARIES, OR LICENSORS. The software products and documentation are furnished by ANSYS, Inc., its subsidiaries, or affiliates under a software license agreement that contains provisions concerning non-disclosure, copying, length and nature of use, compliance with exporting laws, warranties, disclaimers, limitations of liability, and remedies, and other provisions. The software products and documentation may be used, disclosed, transferred, or copied only in accordance with the terms and conditions of that software license agreement. ANSYS, Inc. is certified to ISO 9001:2008. U.S. Government Rights For U.S. Government users, except as specifically granted by the ANSYS, Inc. software license agreement, the use, duplication, or disclosure by the United States Government is subject to restrictions stated in the ANSYS, Inc. software license agreement and FAR 12.212 (for non-DOD licenses). Third-Party Software See the legal information in the product help files for the complete Legal Notice for ANSYS proprietary software and third-party software. If you are unable to access the Legal Notice, please contact ANSYS, Inc. Published in the U.S.A.
  3. 3. Table of Contents ANSYS Topic Help ......................................................................................................................................... 1 1.No Topics Available .............................................................................................................................. 1 2. ANSYS Home Page .............................................................................................................................. 1 3.Advanced Smart Size Settings .............................................................................................................. 1 4. Static or Steady-State Analysis ............................................................................................................. 2 5. Modal Analysis .................................................................................................................................... 2 6. Harmonic Analysis ............................................................................................................................... 2 7. Mode Sup Harmonic Analysis .............................................................................................................. 2 8.Transient Analysis ................................................................................................................................ 2 9. Full Transient Analysis .......................................................................................................................... 3 10. Substructuring Analysis ..................................................................................................................... 3 11. Spectrum Analysis ............................................................................................................................. 3 12. Arc-Length Options ........................................................................................................................... 3 13. Automatic Fit Mode ........................................................................................................................... 3 14. Boolean Operation Settings ............................................................................................................... 3 15. CFD Flow Properties .......................................................................................................................... 4 16. ANSYS Help ....................................................................................................................................... 4 17. Contour Style .................................................................................................................................... 4 18. Apply Coriolis Effects ......................................................................................................................... 4 19.Table of Cospectral Values vs. Frequencies .......................................................................................... 4 20. Damping Specifications ..................................................................................................................... 4 21. Options for DDAM Spectrum ............................................................................................................. 5 22. Device Options .................................................................................................................................. 5 23.Scale DOF Constraints ........................................................................................................................ 5 24. List Binary Files .................................................................................................................................. 5 25. Edge Options .................................................................................................................................... 5 26.Semi Direct Solver Options for Pressure .............................................................................................. 5 27. Read Element File .............................................................................................................................. 6 28. ANSYS Help ....................................................................................................................................... 6 29.Define Additional Element Table Items ............................................................................................... 6 30.Library of Element Types .................................................................................................................... 6 31.Switch Elem Type ............................................................................................................................... 6 32. Export IGES File ................................................................................................................................. 6 33. Expand Single Solution by Load Step ................................................................................................. 7 34. Element Extrusion Options ................................................................................................................ 7 35. ANSYS File Options ............................................................................................................................ 7 36.Scale Forces ....................................................................................................................................... 7 37. ANSYS Help ....................................................................................................................................... 7 38. Hidden-Line Options ......................................................................................................................... 7 39. Import IGES File ................................................................................................................................. 8 40. Create Load Case ............................................................................................................................... 8 41.Execute Macro Data Block .................................................................................................................. 8 42. Element Attributes ............................................................................................................................ 8 43. Meshing Attributes ............................................................................................................................ 8 44. Axes Modification for Graph Plots ...................................................................................................... 8 45. Mode Combination Methods ............................................................................................................. 9 46. Curve Modification for Graphs Plots ................................................................................................... 9 47. Grid Modifications for Graph Plots ..................................................................................................... 9 48. Define Material Model ....................................................................................................................... 9 49. Delete Material Properties ................................................................................................................. 9 iii Release 15.0 - SAS IP,Inc.All rights reserved.- Contains proprietary and confidential information of ANSYS,Inc.and its subsidiaries and affiliates.
  4. 4. 50.Define Nonlinear Material Model ..................................................................................................