Annex II-Technical Specifications

8/12/2019 Annex II-Technical Specifications

1/23

UNOPS/Ethiopia Office/86214/ITB/GOODS/2013-002

Supply and Delivery of Medical and Laboratory Equipment to the Federal Ministry of Health Warehouse, Addis Ababa, Ethiopia)

Annex II

SPECIFICATIONS: All goods to be considered must conform with the below specifications. For electrical equipment, goods must meet with standard in Ethiopia .

LOT 1Comply with UNOPS specs Yes/ No If no, specify technical

differences

1 Fine Scissors Fine Scissors: straight 4-1/2 stainless steel

2 Surgical Scissors Surgical Scissors: straight , sharp/ blunt point 4-1/2 stainless steel

3 Thumb forcepsThumb forceps, 137mm/5.5" Blunt-nosed thumb forceps with serrated tips. Stainless

steel.

4Fine forceps

Fine forceps:curved , and straight 4-1/2; stainless steel; artery, kelly, 140 mm, stainless

steel

5 Dissecting forceps Forceps, toothed tips, treve's, stainless steel, 125mm

6

Needle holder

Needle holder, straight, Mayo-Hegar, 160mm (7") and 180mm (71/4") long, central

grove,box lock, multiple ratchet, stainless steel. 65 from each 160mm (7") and 180mm

(71/4") long. Total 130

7Scalpel handle No 4

No. 4 Scalpel Handle.13cm long and designed to hold blades # 20,21,22,and 25 stainless

steel

8 Surgical Blades #20,21,22,and 25 (1 Pack of each size holds 100 blades)

9Scalpel handle No 3

No 3 Scalpel Handle. 12cm long and designed to hold blades # 10,11,12 and 15 stainless

steel

10 Model DentalClassic tooth series shows five representative types of adult dentition individuallymounted on removable stands: 2 part lower incisor with longitudinal section; 2-part lower

canine with longitudinal section; lower single-root.

11 Surgical blades #10, #11, #12, and #15 (1 pack of 100 blades for each size)

12 MOSQUITO FORCEPS straight Halsted MOSQUITO FORCEPS :5" straight halsted stainless steel

13 MOSQUITO FORCEPS curved Halsted MOSQUITO FORCEPS :5"curved halsted stainless steel

14 Artery forceps Artery forceps, Curved Forceps 5.5"

15 Hemostats, Curved Forceps Kocher Hemostats or equivalent, Curved 5.5"

16 Hemostat Straight Forceps Straight crile forceps 5.5"

17 Kidney dishes Basin, kidney, large, 825ml, 250 x135 x 35mm. stainless steel

18 Kidney dishes Basin, kidney, small, 475ml, 205x108 x 40mm stainless steel

19 Kideny dish Plastice Basin, kidney, small, 475ml,205x108 x 40mm Plastic

20 Basin round , small Basin, round, small, 4 litres, 315x90mm, stainless steeel

21 Basin round , large Basin,round, large,6 litres,315x 127 mm, stainless steeel

22 Suturing needle(Box of 20) Suturing needle rounded and cutting sizes (Box of 20)

23 Cut gut (Box of 10) Cut gut (Box of 10)

24 Pick up forceps Pick-Up Forceps 8" stainless steel

25 Jar of pickup forceps Jar of pickup forceps stainless steel

26 Nail brush Nail brush for (scrubbing lessons)

27

IV stand IV stand, variable height,approx. 1330 to 2330mm. Double hook welded to the upper

pole, telescoping.heavy 4 legged base on castors, furnished with anti-static rubber wheels.

Metalic

28

Dressing trolley.(Local) CASTORS FINISH: 75mm Twin wheel, stainless steel shelves, epoxy powder coated side

frames; FEATURES: Push handle both sides, guard rail on three sides, stainless steel

shelves. Dimensions 1060L x 500W x 950H

29

CYLINDERICAL STERLIZER DRUM, CYLINDERICAL STERLIZER DRUM, With stainless steel,perforated sides with air

tight sliding band to cover perforations, hinged lid with lifting handle

o size diameter 240mmx height 160mm

o size diameter 290 mmx height 160mm,o size diameter 340mmx height 160mm stainless steel,

13 Each

30

Trays for Instrument different size Tray, instrument and catheter, stainless steel, with crown, cover and strap

handle,215x75x38mm. (3x13= 39)

Tray, instrument, shallow, 480x330x19mm, stainless steel>(3x13=39)

Tray, instrument, with cover,stainless steel 225x125x50mm-->(2x13=26)

Tray,instrument, with cover, stainless steel 310x195x63mm--> (2x 13=26)

TOTAL = 130

31

Trolley for Instrument Carriage, dressing with 2 shelves guard rail around top and lower shelf at proximity of

lower shelf, L900xW550xH1000, mounted on four wheel discs with rubber tiers, stainless

steel

Cart, dressing/dispensing, for ward use

Knock-down construction, approx:L950xW550xH1000

two shelves, edges turned high doubled over

mounted on ball-bearing, rubber tired swivel castors

115 kg maximum capacity, stainless steel

Technical Specifications - Comparative data form

Integrated Biomedical Laboratory Equipments for Medical Schools

Company Name:

Name of Company Representative

Email of Company Representative:

Telephone ( Landline):

Telephone (Mobile):

Signature of Company Representative: 1 of 23


2/23



Annex II


32

AUTOCLAVE: FRONT LOADING COMPACT E

AUTOCLAVE: FRONT LOADING COMPACT ELECTRICAL AUTOCLAVE:

40- 50 litter

A fully programmable Touch Screen Controller

Stainless steel chamber

Base shelf within the chamber

ultra quick Swift lock door mechanism

Self contained design with no installation required - just fill it with water and plug it in

and the machine should be ready to for use

A full Range of Accessories

Program and customize cycle parameters;

o High precision control system for accurate sterilization results;

o PC Communication port enables storage of sterilization results;

o Temperature and pressure monitoring ;intuitive display

o Cycle information recovery in the case of power failure or cycle interruption ;

o Insufficient water detector with automatic shutoff ;

o Consistent monitoring of temperature and pressure for real- time

accurate results ;

o Water-level sensors prevent cycle activation when insufficient water is detected in

the chamber or reservoir Capacity:

Double locking safety device prevents door from opening while chamber is pressurized Control lock-out switch prevents starting a cycle if door is not properly locked

Door failure protection prevents door from opening at high pressure16L

33 Huber mall probe Mall probe, 150mm (6"), stainless

34

Electric Autopsy Bone Saw, Oscillating Saw Electric Autopsy Saw oscillating saw: Swing the highest number: More than 12, 000

times per min. Maximum swing range: More than 5 degree. Power supply: 220V/50Hz.

Machinable plaster and polymer materials. Hex drive provides 6 blade rotations extending

blade life by 50% . G. Weight: ~2.9KGS.Dimension: 260*60*50mm.Descriptions should

be in English

35

Model: Articulated standard Human Skeleton Standard articulated full Human Skeleton life size with a stand . Scientific

Human Skeleton Model

Standard anatomical skeleton model of quality for Anatomy laboratory.

Made of durable, washable, unbreakable plastic Flexible joint

ligamentsFlexible vertebral column

Human skeleton weight of the approx. 200 bones, scientific quality and highly detailed

Life-size skeleton model

Skeleton Model Measurements: 170 cm

Skeleton Model Weight: 8 kg

Hanging skeleton model stand with dust cover .

36Model:Disarticulated standard Human Skeleton Standard life-size, disarticulated adult skeleton including all parts of the human skeleton.

37

Model: Human skull male Sets Male human Skull Model, 3 part Features: Highly accurate representation of the fissures,

foramina, processes, sutures etc. medical quality human skull replica that can be

disassembled into skull cap, base of skull and mandible . Mandible should be mounted on

a spring to easily demonstrate natural movement and the tooth individually cast for

realistic dentition .

38

Model: Human skull female Sets Female human Skull Model, 3 part Features: Highly accurate representation of the

fissures, foramina, processes, sutures etc. medical quality human skull replica that can be

disassembled into skull cap, base of skull and mandible . Mandible should be mounted on

a spring to easily demonstrate natural movement and the tooth individually cast for

realistic dentition .

39Foetal skull model Fetal skull, natural cast of a fetal head in the 30th week of pregnancy

18.5x14.5x14cm;0.4kg ,with and without stand with stand

40Foetal skull model Fetal skull,natural cast of a fetal head in the 30th week of pregnancy

18.5x14.5x14cm;0.4kg ,with and without stand with out stand

41

Model :Brain A life size human brain model divided medially in 2 parts along the sagittal plane, which

shows the left and right cerebrum, cerebellum and brain stem, and blood vessels. Should

include cradle base.Size: 16 x 20 x 14 cm, weight: approx. 1.4 kg

42Model: Brain Half Model of the right brain half in life size. Represented are also Cerebellum and brain stem.

On Stand, removable. Size: 16 x 13 x 18 cm, weight: 0.3 kg.43

Model: Nervious system A real life model showing a schematic representat ion of the central and peripheral nervous

system. It is 1/2 life size and is delivered on baseboard.

44

Model :Head and Neck Head model : life-size 6-part head is mounted on a base and features a removable 4-part

brain half with arteries. Eyeball with optic nerve removable and one side of the high

quality model exposes the nose, mouth cavity, pharynx, occiput and skull base. Head

model to be delivered on a removable base for easy display in a classroom

Measurements & Weights ~ 19 x 23 x 22 cm .

45

Model: Head and neck musculature Half head and neck musculature: with superficial and the internal (median section)

structures of head and neck. Half head with musculature is delivered on removable stand

for easy display in a classroom Size ~22 x 18 x 46 cm and Wigth~ 1.1 kg.

Company Name:




Telephone (Mobile):



3/23



Annex II


46

Model 1 :Eye Human Eye Anatomy Model on base: 5 times the li ve size .

Removable parts of this anatomical human eye model include:

* Upper half of the sclera with cornea and eye muscle attachments

* Both halves of choroid with iris and retina

* Lens

* Vitreous humour Weights & Measurements

size ~ 18 x 18 x 20 cm

Weight~1 kg.

47

Model 2 :Eye Human Eye Anatomy Model on base: 3 timeslife size,large anatomical human eye model

shows the optic nerve in its natural position in the bony orbit of the eye (floor and medial

wall). The human eyeball modle that can be dissected into:

Both halves of sclera with cornea and eye muscle attachments

Both halves of the choroid with iris and retina

Eye lens

Vitreous humour

Size ~18 x 26 x 19 cm and Weight~1.1 kg

48

Model :Ear Human Ear Model 4-5 times life-size viewing from anywhere in the classroom! The

Giant ear model should represents the outer, middle and inner ear. Auditory ossicles and

labyrinth with cochlea and vestibulocochlear nerve are removable from ear for more

detailed anatomy study. Ear model to be delivered on base for easy display. Size ~25 x 41x 25 cm.

49

Model: Phantom Head (Dentistry)Human Dental Model : classic tooth series shows 5 representative types of adult dentition

individually mounted on removable stands:

2-part lower incisor with longitudinal section

2-part lower canine with longitudinal section

Lower single-root pre-molar

2-part lower twin-root molar with longitudinal section showing caries attack

3-part upper triple-root molar with longitudinal section and caries insert Each tooth is

also available singly.

50

Delivery period Delivery time to Fededral Ministry of Health Warehouse, Addis Ababa, Federal Republic of

Ethiopia from date of receipt of purchase order must not exceed 90 days (Please specify)

51 Catalogues Attach picture/catalogue of item offered

52 Packing Packing to be done according to UNOPS packing and Shipping Instructions

53 Brand Brand name / model number for all items

54 Origin Country of origin of all items

55Warranty Warranty if different from manufacturers . Warranty begins from date of acceptance of

oods b UNOPS Ethio ia. (Please s ecif )

LOT2

1

Model :Upper and lower respiratory tract Scientific Lung Model with larynx, 7 part :The lung model with larynx is first class. Lung

model containing the following removable parts for added anatomical detail:

* 2-part larynx

* Trachea with bronchial tree

* 2-part heart

* Subclavian artery and vein

* Vena cava

* Aorta

* Pulmonary artery

* Esophagus

* 2-part lung (front halves removable)

* Diaphragm

Descriptions should be in English

2

Model:The Heart

Seintifiec Heart Model : size: 2-times life-size heart model with all structures of the

human heart identified . The atri um wall s and the fr ont heart wall should be

removable to reveal detail es of the heart structur e. Colored to depict the anatomical

structuer of the human heart. Additionally the heart model should depict the upper

section of the esophagus, the upper bronchi and the ascending aorta and the f rontheart wall and the atri umwalls can be removed. Heart delivered on removable stand.

Weights & Measurementssize ~32 x 18 x 18 cm and wt ~1.3 kg.

3

Model :The Liver and Biliary systemSientific Model of the Human Liver and Biliary system: model shows the liver with:

Ducts

Gall bladder

Pancreas

Duodenum

Vessels

Extra-hepatic ducts with gall bladder

Main pancreatic duct and their orifices

The anatomy of the liver with Gall Bladder, Pancreas and Duodenum is graphically

illustrated. The liver with gall bladder, pancreas and duodenum is delivered on baseboard.

Company Name:




Telephone (Mobile):



4/23



Annex II


4

Model : Gastrointestinal System Sientifice Digestive system Model : Life-size digestive system model that demonstrates

the entire digestive system in graphic relief. The digestive system mounted on baseboard.

Digestive System features:

Nose

Mouth cavity and Pharynx

Esophagus

GI tract

Liver with gall bladder

Pancreas

Spleen

The duodenum, caecum and rectum of the digestive system should be opened . The

transverse colon removable. Size~81 x 33 x 10 cm weight 4.4 kg.

5

Model :Kidney and Urinary system

Dual Sex Urinary System model: showing:

Structures of retroperitoneal cavity

Large and small pelvis with bones and muscles

Inferior vena cava

Aorta with its branches including iliacal vessels

Upper urinary tract Rectum

Kidney with adrenal gland.

One front half of a kidney is removable from the anatomical model of the urinary system.

With easy to change male insert (bladder and prostate, front and rear half) and female

insert (bladder, womb and ovaries, 2 lateral halves) . Parts are numbered on the Dual Sex

Urinary System.

6

Model: Male reproductive system Male Reproductive System Model Activity Set: Useful for topics such as prostate

cancer, vasectomies and sterility. Model depicting all male reproductive organs in

relationship to one another, as well as a greatly magnified section of the sperm;

Measurements: 61 x 45 cm; 1 kg

7

Model: prostate Prostate Model (schematic):

A prostate model providing a cross section of the male genital organs and showing ahealthy prostate with bladder, urethra, testicle, symphysis and rectum. The narrowing of

the urethra due to the change of the prostate is made clear via the four cross sectional

views on the base of the prostate model. The anatomical structures of the prostate model

shown with simple schematic coloring.

8Model: Penis anatomic model Penis Model : Model of cross section of male genital organs showing all structures in

detail, mounted on a base.

9

Model :Female reproductive system Female Reproductive System Model Activity Set: Showing womens health issues and

pregnancy. Detailed lateral section of the lower female torso showing partially sectioned

organs and a magnified, cross-section of the ovum. The model illustrates the internal body

structure. Weights & Measurements: ~61 x 45 cm; 1 kg

10

Model :Pelvic model female Female Pelvis, 2 parts:

A median section female pelvis model with a removable half of genital organs incl uding

bladder and rectum . The abdominal and pelvic muscles should be shown in anatomical

detail. The pelvic model is delivered on baseboard.Weights & Measurements: ~26 x 22 x

17 cm, 1.65 kg

11

Model- Pregnancy series Pregnancy Series - 9 Models;

Containing:

Embryo approx. 4 weeks old, 25 times life-size

1st Month Embryo,

2nd Month Embryo,

3rd Month Embryo,

4th Month Foetus (Transverse Lie)

5th Month Foetus (Breech Position)

5th Month Foetus (Transverse Lie)

5th Month twin foetus (Normal Position)

7th Month Foetus. Descriptions should be in English

Company Name:




Telephone (Mobile):



5/23



Annex II


12

Model: 3/4 life-size dual sex - muscle, 45 parts Dual Sex Muscle Torso, 31-part

A torso depicting both the superficial and deep muscles, and the two main muscles, the

deltoid and gluteus maximus can be removed for closer studies. Allowing the study of the

vertebrae, the spinal cord, spinal nerves and vertebral arteries, exchange the male and

female genital inserts, discover the internal structures of the brain, etc. All the organs in it

are hand painted;

The following parts are removable from the torso:

6-part head

Chest and abdominal wall with muscles

7th thoracic vertebra

Female mammary gland

Gluteus maximus and deltoid muscle

2 lungs

2-part heart

2-part stomach

Liver with gall bladder

4-part intestinal tract

Front half of kidney

3-part female genital insert with fetus

4-part male genital insert .

13

Model: Functional larnyx Functional Larynx Model, 2.5 times full-size

The epiglottis, vocal cords and arytenoid cart ilage should be movable in the functional

larynx. Additionally the following structures of the human larynx are represented:

Hyoid bone

Cricoid cartilage

Thyroid cartilage

Thyroid

Parathyroid glands

The Functional Larynx should have a stand.

Weights & Measurements:~ 14 x 14 x 28 cm; 0.8 kg.

14

Model: functional shoulder joint Functional Shoulder Joint Model

A functional shoulder joint model of a naturally-sized right joint with ligaments showing

the anatomy and possible physiological movements (e.g. abductions, anteversion,

retroversion, internal and external rotation) in exceptional detail. Realistic color of thenatural-cast bones; The cartilage on the joint surfaces should be marked in a separate

color; The joint model consisting of shoulder blade, collarbone and upper arm stump; the

functional shoulder joint model should be mounted on a base. Weights & Measurements:

~22 cm, 0.41 kg.

15

Model: functional hip joint Functional Hip Joint Model

A functional hip joint model of a natural-sized right joint with ligaments showing the

anatomy and possible physiological movements of the human hip joint (e.g. abductions,

anteversion, retroversion, internal and external rotation) in detail. The color of the natural-

cast bones should be realistic and the cartilage on the hip joint surfaces marked with a

separate color. It should consist of thigh stump and hipbone and should be mounted on a

base. Weights & Measurements: ~32 cm, 0.56 kg.

16

Model: functional knee joint

Functional Knee Joint Model

A functional knee joint model of a naturally-sized right knee joint with ligaments showing

the anatomy and possible physiological movements (e.g. abductions, anteversion,

retroversion, internal and external rotation) in detail. It should clearly define the ACL and

PCL. The color of the natural-cast bones of the knee joint should be realistic. The

cartilage on the knee joint surfaces is marked with a separate color. It should consist of

thigh stump, shinbone stump and calf bone stump, menisci and patella and should be

mounted on a base. Weights & Measurements: ~32 cm, 0.55 kg.

17

Model: functional elbow joint Functional Elbow Joint Model

A functional elbow joint model of a naturally-sized right elbow joint with ligaments

showing the anatomy and possible physiological movements (e.g. abductions, anteversion,

retroversion, internal and external rotation) in detail. The color of the natural-cast bonesof the joint should be realistic. The cartilage on the elbow joint surfaces is marked with a

separate color and should consist of a stump of the upper arm, ulna and radius. It should

be mounted on a base. Weights & Measurements:~33 cm,0.285 kg.

18

Model: skin Skin, Block Model, 70 times full-size

A skin model showing a section of human skin in three dimensional form. Individual skin

layers are differentiated, and important structures of the skin such as hair, sebaceous and

sweat glands, receptors, nerves and vessels are shown in detail. The skin block model

should be mounted on baseboard.

19 Model : Human Muscular system complete dual sex muscular figure, 45 parts,on stand

20Mankins Patient care dolls-adult Basic patient care Manikin,female/male features, full size adult with movable joints, as

well as soft fingers and toes,include IM, IV, Subcutaneous injections,soft hand for finger

prick,and stomies,allows basic&advanced patient care.

Company Name:




Telephone (Mobile):



6/23


Supply and Delivery of Medical and Laboratory Equipment to the Federal Ministry of Health Warehouse, Addis Ababa, Eth iopia)

Annex II


21Manikin child patient care doll Child patient care mankin with rotatable arms and legs and articulating hand,allows

training of basic and advanced patient care

22Manikin Male: Human models with all internal

organs

Male deluxe torso with head,20 parts,parts are easily removable to facilitate teaching

23Manikin: Female :Human models with all internal

organs

Female deluxe torso with head, 20parts,parts are easily removable to facilitate teaching

24 Strechers wheeledStrecher,wheel and carrying combination. Equipped with litter,partial utility shelf,

(blanket), Dimensions L1830XW686XH864MM made from steinless steel

25 Automatic embalming SetTo be supplied with complete electric cord, plug and suitable to work on 220 volts, 1ph

50 hz, ac supply.

26

Anatomical Charts of all systems (set) (Size: 42" W x 62" H. ) separet charts for each system should be included in each set .

Head and Neck, Eye, Ear, Cardiovascular system, Respiratory system, Gastro intestinal

,Genitourinary, Reproductive (Male ,Female) Skeleton(ostiology),Body Muscules,,

Nervus system .

27Interactive Full Human anatomy 3D DVD/CD

of the different systems

Interactive human anatomy and physiology DVDs of all systems of the body (Set of

different systems ).

28 Lab cupboard anti-corrosion, ventilate fume freely, meets the national standard, Material: FRP

29Model: Embryo model Pregnancy series embryo model from 1st month to 7th month embryo or fetus, all models

mounted together on a base

30

Prepared Slides:Histology prepared slides of the

all systems

Set of prepared Histology slides(100 slides in each set) of all organs

31Prepared Slides :Embryology prepared slides Set of prepared Embriollogy slides (50 Slides in each set) of the embryo at different

stages

32Prepared Slides :Pathology prepared slides of the

all systemsSet of prepared Pathology slides (100 slides in each set) of all organs

33

Slide try cabinet Store up to 240 1 x 3 microscope slides in this polypropylene cabinet; it holds 12

horizontal slide trays. The clear acrylic door slides vertically. Slide trays are available

separately. Size: 7 3/4L x 14W x 7 1/2H.

343D DVD/CD Histology A full set 3D DVD/CD of the histology of the different normal tissues of the body in

full

35 3D DVD/CD Embryonic Development Afull set 3D DVD/CD of the embryonic development full set

363D DVD/CD Phatology of all systems A full set 3D DVD/CD of the pathology of the different normal tissues of the body full

Binocular tube, 45 degree inclination, 360 degree rotatable

Rectangular mechanical stage with coarse and fine adjustmentsCondenser with iris diaphragm and filter

10xWF Eye piece, With low voltage illuminator,Objectives 4x,10x,40x,100x & oil

immersion,Dust cover and hard wooden cabinet

Main supply voltage 220V, 50Hz

40








goods by UNOPS Ethiopia. (Please specify)

LOT3

Measuring lab pipette, different sizes marked in micro liter of 10ml, 15ml, 25ml, and50ml, glass, volumetric, 3 of each sizes: [(10 ml x3x13) + (15mlx3x13) + (25mlx3x13) +

(50ml x3x13) = 3900

1

Pipette different sizes 5mL Transfer Pipet, Graduated, 500/dispenser box, 10 boxes/case (5000 each). Transfer

pipets, non-sterile. 5mL capacity. Graduated to 1mL. 150mm long. 22 drops/mL.

Packaging: Box: 500 each

2 Transfer Pipette different size

Test tubes, pyrex of different sizes with stopper (Glass). Each size shall be with rim and

rimless (culture tube). Sizes: 10mm x 75mm , 12mm x 75mm, 16mm x 100mm, 18mm x

150mm, 24mm x 150mm. 1 box of each size. 1 Box with a minimum of 72 tubes. 1 box is

with rim and the other box is rimless. 5 boxes x2= 10 boxes (rim and rimless), for 13

schools multiply by 10 = 130 boxes

3

Test tubes of different sizes with stopper Stoddard type with finger grip; brass or nickel steeel, works with maximum diameter x

overall length (mm) of 25 mm x 127mm. A pack of 10 for each school. 1 pack has 10

clamps. 13 packs x 10 clamps/pack= 130 clamps

4 Test tube clamp Funnel Separatory Glass 500ml and 1000ml 2 of each size. (2x2x13=52)

5

Funnel Test tube rack 2 of each size tube, polypropylene for 10mm x 75mm , 12mm x 75mm,

16mm x 100mm, 18mm x 150mm, 24mm x 150mm. 10 racks. For 13 medical schools:

13x10=130 racks.

6

Test tube rack Table top Centrifuge, adjustable speeds to 5,500 rpm, capacity of 15mlx8

With full accessories : Micro centrifuge tube with cap blue screw, printed graduated

cones, 50/rack tube, urine centrifuge with sediment bulb and flare.

Power supply: 220V, 50Hz

7

All purpose centrifuges Centrifuge, Micro-Heamatocrit, direct reading,24 tube capacity: accommodates twenty

four 75mm specially calibrated color coded , plastic heparinised capillary tubes, five

minute centrifugation cycle, complete with adjustable 1 to 5 minute automatic timer and

swivel magnifier.

Power supply 220V/50Hz

Microscope (scientific ) Equivalent to Olompus)

37

Company Name:




Telephone (Mobile):



7/23



Annex II


8

Micro hematocrit centrifuges Advanced microprocessor for accurate weighing results and fast stabilization

Lock-down capable

Weighting capacity: 0.001gm- 320gm

Accuracy : 0.001-0.0001gm /1-10mg/

Stainless steel weight platform

RS 232 bi-directional interface for printer or PC connections

Durable ABS housing

Built-in application programs for mass unit conversion, net total formulation, % weighing

and part counting

Simple one-button external calibration

Power supply: 220V/50Hz

9

Analytical Chemical Balance Projection Microscope

* Easy Viewing on Extra Large Size Projection Screen, 200mm Diameter.

Eyepieces and Magnification

* Four Magnifications: 75x, 150x, 300x, and 600x.

* Projection Eyepiece Included: 15x.

* Four Objectives: 5x, 10x, 20x, 40x.

* Spring Loaded 20x and 40x Objectives to Protect Slides.

Condenser - Iris - Filters

* 1.25 N.A. Abbe Substage Condenser, Condenser Movement Knob, Iris Diaphragmand Swing-Out Filter Holder.

* Rack and Pinion Steel Gears for Easy and Better Condenser Movement.

* Condenser Alignment Screws.

Illumination

* 12V/100W Halogen Transmitted Base Illumination.

Stage Specifications

* Graduated Mechanical Stage Size 130mm x 120mm with X-Y Slide Movement

Knobs.

Focusing : Fine and Coarse Focusing Knobs.

Frame - Base - Size - Weight : Total Overall Height of Microscope: 580mm.

* Instrument Weight: 44.5 lbs.

Included Items : Stage Micrometer with 0.01mm Resolution for Precise Calibration of

On-Screen Reticle.

* Measuring Reticle Built into Viewing Screen.

* Two Movable Mechanical Pointers on Screen. * Built-In Side Drawer with Lock and Key.

* should comes with Instruction Manual, Dust Cover, Extra Bulb, and Fuse.

10

Projection Microscope Screen, projection, portable, size ~1.27x1.27M(50"x50"), collapsible tripoid mounting,

matt white fabric,vinyl based, fungus and flame resistant, adjustable screen height, with

tension bars and metal case.

11White Screen Metalic frame (aluminum) white board; frame: pine wood; board: MDF; Non-magnetic

white surface; size: ~250cm*120cm

12White board

Laboratory furniture; size:3200L*1200W*750Hmm; material:MDF with fireproof board

13

Laboratory table with shelf Microscope (scientific ) Equivalent to Olompus): Binocular tube, 45 degree inclination,

360 degree rotatable. Rectangular mechanical stage with coarse and fine adjustments.

Condenser with iris diaphragm and filter. 10xWF Eye piece, with low voltage illuminator;

Objectives 4x, 10x, 40x, 100x and oil immesion; dust cover. Power: 220V, 50Hz.

With additional 5 Spare halogen bulbs and Fuses

14

Microscope (scientific ) Equivalent to Olompus) BINOCULAR STUDENT MICROSCOPES

1) Style: Binocular tube, 45 degree inclination, 360 degree rotatable..Built in mechanical

stage of this microscope allow smooth X-Y travel in 0.1 mm graduation.

2) Rack and pinion removable

3) 1.25 Abbe condencer & diaphragm for resolution and contrast control

4) Eye Pieces

High quality two eye pieces

10 x with built pointer

Achromatic wide field

5) Objectives

Objectives should be wide field

S flat achromatic, or Phase Achromatic and parafacul, give clear

sharp images

Four objectives as 4 x, 10 x, 40 x 100 x (oil immersion)

6) Stage Horizontal

Square stage dimensions not less than 120 mm x 120 mm

Spring-loaded paired stage clamps for exact positioning of the

specimen

7) Nose Pieces : Quadruple revolving nose pieces

8) Condenser : NA 0.65 with disc diaphragm

NA 1.25 Abbe Condenser in rack and pinion focusing mount

9) Dust cover

10) Bulb Tungsten Halogen 1500 220-240 V AC

With additional 5 spare halogen bulbs and Fuses

15

BINOCULAR STUDENT MICROSCOPES Timer,stop-clock,spring wound,with second hand:100mm dial,divided 0-60x1:two large

large sweep hands,one indicating seconds the other recording minutes, start/stop

lever;zero reset lever.Housed in metal case.Runs for 30 hours on one winding.

Company Name:




Telephone (Mobile):



8/23



Annex II


16

Laboratory timer Beaker different sizes in ml (50, 100, 250, 500, and 1000) with spout and rolled rim,

borosilicate HRG glass. Of the different size the following amounts are needed 50 ml in

in Quantity of 10; 100ml in quantiry of 15; 250ml in Quantity of 20; 500ml in Quantity

of 10; and 1000ml in in Quantity of 5 .

17Beaker, different size Burette, Teflon stopcock with stand different sizes: ml(25,50,100) two of each size.

Thus, 3x2x13=78 burettes

18

Burette, teflon stopcock Stand, Single Burette Clamp. 2 of each size. 5x8 Support stand has a sturdy cast iron

with 20" steel rod. The base shall be sturdy and chemical resistant. Stand shall come with

a burette clamp with plastic coated jaw. Stand shall come with 2 aluminum clamp holders.

2x13=26 iron stands are needed.

19

Burette stand and clamp set, different sizes Flasks of 250 ml, 500 ml and 100 ml (5 each), Erlenmeyer, narrow mouth,vial neck,

borosilicate glass HRG. (Pyrex). 5 flask from each of of the 3 sizes is needed; hence,

5x3x13=195 of Erlenmeyer flasks are requested.

Company Name:




Telephone (Mobile):



9/23



Annex II


20Flasks Graduated cylinder different size ml(25,50,100ml). 4 from each size. 3x4x13 medical

schools = 156 graduated cylinders needed.

21 Graduated cylinder Iodine flask Glass sizes 100ml ,250ml ,500ml, 3 from each size

22

Iodine flask Automatic Electrical Autoclave: with a capacity of 40-60 Liter chamber sizes.

Table top model ; Front Loading Compact Autoclave;An ultra quick Swift lock door

mechanism

pre-set sterilization programs;

Program and customize cycle parameters;

High precision control system for accurate sterilization results;

PC Communication port enables storage of sterilization results;

Temperature and pressure monitoring ;intuitive display

Cycle information recovery in the case of power failure or cycle interruption ;

Insufficient water detector with automatic shutoff ;

Consistent monitoring of temperature and pressure for real- time accurate results ; Water

level sensors prevent cycle activation when insufficient water is detected in the chamber or

reservoir Capacity:

Durable stainless steel chamber and door with electro-polish finish Double locking

safety device prevents door from opening while chamber is pressurized Control lock-out

switch prevents starting a cycle if door is not properly locked Door failure protection

prevents door from opening at high pressure. Power supply: 220V/50Hz

23 Automatic Electrical Autoclave

Digital Precision BalanceWeighting capacity: 0.0001gm- 320gm

Accuracy:0.001-0.0001gm /1-10mg/

Power supply: 220V/50Hz

24 Single pan micro balancesilica gel glass plate;1.20*20cm, 10*20cm, 5*20cm; analysis and preparative plate;

coating:0.2-0.25cm, 0.4-0.5cm and 1cm

Company Name:




Telephone (Mobile):



10/23



Annex II


25

Chromatography Polyscience microprocessor Water Bath 10L Capacity, 18.84 lb. WD10L11B; Control

bath fluids at temperatures as high as 100C 60C without cover with 0.1C precision and

0.2C uniformity."

26

Water bath Technical Specification

PH Range: 0-14 pH,

Resolution: 0.01 pH

Temperature Range: 0.0 to 100C (Manual Compensation)

Display: 31/2 Digit LED Display

Power Supply: 230VAC 10%, 50 Hz

With Calibration check facility & Calibration Error indication for 7.00 & 4.00 pH

Supplied with Combination Glass pH Electrode (0-70C), Standard Buffer Tablets,

Electrode Stand with Clamp, Dust Cover, Power Cord, Operational & Instruction

Manual, Manufacturer Test Certificate & Warranty Card

27

Digital pH meter Wavelength range: UV and Visible ranges 200 to 1000 nm

Wavelength accuracy (+/-) 2 nm

Spectral bandwidth 5 nm

Light source Xenon flash lamp

Detector Photodiode array

Number of cuvettes oneSize of cuvettes 100 l, 700 l, 1.5 ml, 3.5 ml

Pathlength 1 mm, 2 mm, 5 mm and 10 mm

Display 2 x 24 alphanumeric built-in backlit LCD display

Printer Built-in alphanumeric/graphic

Interface RS-232 serial port

Operating temperature 540 C

Photometric range 02 AU

Scan speed 200800 nm in 20 seconds max

Photometric repeatability 0.02 AU in a 0.12.0 AU range (9 readings) and over a

200800 nm range.

Power requirement 220 V/50Hz

28Spectrophotometer Compact requiring very little room; Glass-free, chemical resistant housing resists damage

by accidental falls or scratches.

29 Magnetic Stirrer Heat resistant, energy efficient and low maintenace laboratory table lamp. Powersupply : 220V/50Hz

30Table lamp Heat resistant, energy efficient and low maintenace laboratory table lamp. Power

supply : 220V/50Hz

31









LOT4

1Differential cell Counter, manual (Manual Cell

Counter)

Manual Blood cell (Differential) counter. Counter specificaly for every blood cell type. it

is manual counting for demonstrating how the student counts manually

2 Hemoglobinometer Automated Battery operated hemoglobin meter with full accessories

3 E.S.R. tubes ESR West green Glass Tube

4 E.S.R. tubes (Wintrobe)Capacity:0-105mm; Graduation:1.0mm; Length:120mm; Qty(pcs)/Ctn: 1000(50pcs*20)

5 E.S.R Stands With stainless steel screw or plast screw

6 Blood Grouping sets with antisera ABO-Rh Typing with Synthetic Blood KiPart #7001001 Pkg Qty 1

7 WBC counting chamber (Haemo - cytometer)

Counter,blood cells,differential,9 units,eight keys and one totalizer,each with range 0-

999,with buzzer at 100 and dual reset knob. It is manual counting for demonstrating how

the student counts manuall

8 Stop watches, Table model Stop watches

9 Microscope slides,plain 72/box and frost 72/box (10 box from each type). 20 boxesx72slides/box x13

medical schools =18720 total slides (9360 plain slides and 9360 frost slides)

10 Cover slips glass, 22mm, 100 slides/box; 10 boxes each for 13 medical schools= 130 boxes

11

Universal Centrifuge. Bench top. Table top Centrifuge, adjustable speeds to 5,500 rpm, capacity of 15mlx8

With full accessories : Micro centrifuge tube with cap blue screw, printed graduated

cones, 50/rack tube, urine centrifuge with sediment bulb and flare

Two sets of spare carbon Brushes,

Power supply: 220v, 50/60Hz

12Spirometer for students (Manual). Includes an oxygen connector for supplemental oxygen - convenient handle - flexible

popple tubing and bedrail holder. -2500ml capacity.

Made of heavy duty chrome plated steel with rubber bumper

standard size with adjustable back rest

mounted on castors with locks

adjustable to different position and with over bed table

Made of heavy duty chrome plated steel with rubber bumper

standard size with adjustable back rest

mounted on castors with locks

Pediatric size

15 Nasal speculum for different sizes Nose speculum adjustable size (0,2)

Hospital bed-child

14

Hospital bed - Adult13

Company Name:




Telephone (Mobile):



11/23



Annex II


16 Specific gravity measuring device (Manual) Hand Held Digital Specific Gravity / Salinity Water Meter.

17 Snellen's chart Standard - for testing visual acuity

18 Ishihara Chart set Standard - for color blindness test

19

High power centrifuge machine

Maximum Speed (rpm) 18,000

Maximum Capacity 4 x 200 ml

Drive System Direct self-centering drive system with brushless induction motor

Braking System Dynamic electric brake system

Power Consumption 0.8 kVA- 2.0 kVA

Power supply 220V/50Hz

Includes all accessories such as sealing lids and tubes adaptor

Safety Features

Over speed detection

Imbalance detection and cut-off

Four point lid fixing

Automatic motor driven lid lock with emergency lid lock release

Stainless steel chamber with additional inner guard ring

20

High power centrifuge machine Materials of Construction: Steel and molded plastic case, aluminum shelves, foamed

polyethylene insulation, corrosion-resistant blue enamel finish, rubber feet

Temperature: Incubating temperature continuously adjustable between room ambientand 55

0C (131

0F), thermostatically controlled and indicated by included thermometer.

Variation within 0.5 0 C in stable ambient.

Electrical Power: 230 volts 50/60 HZ

Power Requirement: 100 watt heater, actual power used depends on ambient

temperature and operating temperature control sett ing

Capacity:

Three fixed rack shelves spaced 1 (38 mm) apart. Shelf dimensions approximately 11

wide by 5 deep (270 mm x 140 mm).

Operating Conditions: 170 C to 270 C 20% to 80% relative humidity, no condensing

Altitude limit: 2,500 meters

20 Laboratory Incubator,

Low Speed Centrifuge, brushless motor, fixed angle rotor, LCD micro centrifuge,

microprocessor controlled.

A front panel LCD display is for displaying -Pre-set and remaining centrifugal time -Pre-

set and running speed. -Pre-set and running RCF

Max. Capacity 4 x 100 ml

Speed from 0-4000 rpm

Centrifugal chamber is made of stainless steel

Rotor is made from high-strength engineering plastics

The lid can be locked for operation safety.

Safety function:

operation

spinning with alarm beeps.

exceeding the pre-set speed.

Noise level is


12/23



Annex II






Skills Laboratory Equipments Standard for M LOT5

1

STETHOSCOPE Stetescope with binaural unit,plain spring non folding frame,with plastic ear tips,black

vinyl stethoscope tubing double stem chest piece,combined bell and diaphragm sprague

bowless type.With spare pair of ear tips Stethoscope,foetal,Pinard,monaural,unbreakable

plastic,Standard Length 22/56 cm, 27/69 cm; Total Weight 165, 175 grams, Diaphragm

Diameter 1.7/4,3 cm, Bell or Small Diaphragm, Diameter 1.3/3,3 cm, black finish

chestpiece and eartubes

2 Sphygmomanometer:Aneroid Adult Aneroid type; Caliberation 0 to 300mm Hg;Complete with hook,velcro fabric cuff (adult

size),bulb and valve; precision manometer with clip for fix .With case.

3Sphygmomanometer:Aneroid Baby Aneroid type;Caliberation 0 to 300mm Hg;Complete with hook,velcro cuff( Baby

size),bulb and valve,With zipper case

4

Sphygmomanometer: Mercurial Desk top Adult Traditional blood pressure measuring instruments with mercury locking facility, Range 0-

300 mm Hg packed in lightweight metal case.

Features:

Easy to read with clear tube

Accurate reading

Emulsoid Bladder & Soft emulsoid BulbMercury lock facility.

Accessories

Cotton/Nylon cuff

Latex Bulb and Inflation Valve

Technical Specification

Measure Scope: 0-300mHg

Accuracy: 3mmHg

Glass Tube: 3.5 to 4.0mm

5REFLEX HAMMER Reflex hammer: 7"- 7.5", solid stainless steel handle with triangular rubber Head, rubber

ring Latex free packing

6

PENLIGHT Reliable, furnished, and ready to operate. Aluminum-cased reusable penlight with strong,

nickel-plated steel slotted pocket clip. Finished in multi-layered gloss metallic lacquer.

Two AAA heavy-duty zinc chloride batteries included.

Aluminum housing with metallic gloss lacquer Activated by pressing top button

Option to "lock on" by twisting top mechanism

Measures 5 1/4" long, 1/2" diameter

Two AAA batteries included

7TUNING FORK Tuning fork Medical: Alumminnium Alloy of different frequencies (128Hz, 256Hz,

512Hz) 3 of each 3X 3=9

8

Oral /Axillary thermometer (Mercury ) Clinical oral/Axillary thermometer (Mercury ) , Celsius scale (350- 42

0C) and Fahrenheit

(940F - 108

0F) , Supplied in protective case.

Lense front. Stubby bulb.

9 Oral /Axillary thermometer (Digital ) Basic Clinical oral/Axillary thermometer (Digital ), Celsius scale, with case .

10Rectal Thermometer (Mercury ) Clinical thermometer (Mercury ) , Celsius scale (35

0- 42

0C) and Fahrenheit (94

0F - 108

0

F) , Supplied in protective case.Lense front. Stubby bulb.

11 WEIGHING AND HEIGHT SCALE(Mechanical)

WEIGHING AND HEIGHT SCALE (Mechanical)A weight scale measures body weight and height.

Wight measuring: maximum scale value is 120kg, the minimum centi-value is 0.5kg.

length measuring: measuring rang is 70-190cm,the minimum centi-value is 0.5cm error

0.5cm

Main board area:~(lengthwidthheight) 700280930mm.

Outer dimension:~ (lengthwidthheight) 700280930mm

Weight: ~20- 26kg.

Scale to put human body weight through lever system, transfer to measuring spring.

Alters the spring extending to index reverse rotation through teeth beltgear in the face

Rubber pedal sticks to main board as an anti slide.

Length scale consisting of three different diameter round pipe, the mid pipe and inner

pipe with length graduation cladded on the outer pipe in turn, when using, should stick at

any position, the top of inner pipe has adjustable measuring board, pull up the measuring

board, make it and pipe right angle ,

Warranty 3 years from date of delivery

12 BABY SCALE :MECHANICAL SLIDING WEIG

BABY SCALE: MECHANICAL SLIDING WEIGHT BABY SCALE

With Baby tray, the Scale platform and

Baby tray to be mounted on the Scale platform

Scale platform : with sliding Weights and Sliding weight bar

Should have device locking the baby Tray with the Scale platform

Max. Capacity: ~16 kg

Graduation: 10 g

Dimensions~ (WxHxD): 550 x 195 x 300 mm

Weight: approx. 5,8 kg

Operating Manual English

Warranty 2 years from date of delivery scale corresponds to standards and requirements of the European Directive

90/384/EEC.or equivalent

Company Name:




Telephone (Mobile):



13/23



Annex II


13

Light source (Lamp ) Color Temperature: 3600k AC: 95v-240v Power Supply: 30-50w Lamp Life: Halogen

2000h Spare Parts: Table Clip, Guide Rail Clip, Wall Clip, Floor Prop. N. W: 3.8kg

Packing Size: 850*210*250mm Feature: Material: Steel; to be deilverd with spare lamp

14

Negatoscop (Xray viewer) An aluminum frame.Thickness : 22mm. Size can be custom. Lighting source: T5 or Led.

LEDs on edges provide higher optical efficiency with lower power than CCFL and thinner

backlight design.

Excellent illumination, NO flickers, lifetime 90.000 hours, 12V voltage.

Power Supply: 220V/50, Life-time 90,000 hours,

15MEASURING TAPE Measuring Tape : 200 cm; also measuring in inches; made of plastic or equivalent,

graduation to be clear and to be printer with durable colouring .

16

EXAMINATION COUCH EXAMINATION COUCHE

Basic examination couch :Suitable and stable for examining and treatment of an adult

patent

Made of Sturdy 32 mm tubular steel frame

Powder-coated finish

Vinyl(equivalent ) covered 40 mm foam padding

Adjustable head rest

Compatible with Casualty Couch accessories

Dimensions: ~L 1820 mm, W 610 mm, H 780 mm

17BASIC OBSTETRICS/GYNECOLOGY

EXAMINATION COUCH

BASIC OBSTETRICS/GYNECOLOGY EXAMINATION COUCHES

Wiith two sectional mattress base with perineal cut suitable for Gynecological and

Obstetrics examination ,procedueres and delivery

Made of Sturdy 32 mm tubular steel frame

Powder-coated finish

Vinyl(equivalent ) covered 40 mm foam padding

Adjustable head and hind rest

Compatible with Casualty Couch accessories

Dimensions: ~L 1820 mm, W 610 mm, H 780 mm

18

Transfer BOARD TRANSFER BOARD

The Transfer Board should have

a smooth top and bottom surface which allows for easy, low

friction gliding, facilitating patient transfers.

Comfort, convenience and adaptability are built into this transfer board.

Manufactured from high impact polyurethane six grab slots with rounded, smooth edges for operator ease.

Length Width Depth Weight ~125 cm 46 cm 0.5 cm 2.3 kg

19

EMERGENCY POLE STRETCHER EMERGENCY POLE STRETCHER

lightweight, high-strength emergency stretchers suitable for first aid response

made with PVC coated nylon covers (equivalent)that are heat sealed making them

resistant to blood, body fluids and mildew and easy to clean.

lightweight aluminum poles with contoured,

flexible hand grips for easy handling.

Hinges at the centre permitting the stretcher to dual fold for compact storage.

Color orange preferred

Carry cases.

Length Width Height Weight Load Limit

~ 231 cm 55 cm 14 cm 6 kg 159 kg

20

OPHTHALMOSCOPE SET A basic Ophtalmoscope set, with one-piece handle and diagnostic head. Mirror optical

system, with 16 viewing lenses from -15 to +20 diopters with bulb spare, supplied with

batteries protective case, padded

21









LOT 6

1OTOSCOPE SET Otoscope set,with one piece handle and diagnostic headfiber-optic light speculae 2.5,3,4,5

MM,Poly. Re-usable with Bulb/Globe Spare,supplied with batteries. Case, padded,

protective and storage

2EAR SPECULUM OF DIFFERENT SIZES Specula ear,Gruber, set of 4 sizes:size 4. 5mm, 5.5mm, 6.5mm,7.5mm, brass chromium

plated

3 TONGUE DEPRESSOR WOODEN Tongue depressor wooden

4TOUNGE DEPRESSOR(METALIC) Tounge depressor, metallic, Mayo or equivalent, 170x22mm, tapering to 15mm at narrow

end, both ends slightly curved in opposite direction, stainless steel

5 NASAL SPECULUM Nasal Speculum; Beckman type or equivalent; size medium 5 1/2" stainless steel

6NASAL CATHETER For administration of oxygen for nasopharyngeal route - Length : 50cm; Sizes: FG 8, 10,

12, 14; dispossable ; made of clear material

Company Name:




Telephone (Mobile):



14/23



Annex II


7

OROPHARYNGEAL AIR WAY OROPHARYNGEAL AIR WAY of different size (6 different sizes) 4 from each size for

training. Soft, clear PVC plastic. 4 from each size:

Size for Newborn, 40mm

Size for Infant, 50mm

Size for Small Child, 60mm

Size for, 70mm

Size for Med. Adult, 90mm

Size for Large Adult, 100mm. 4x6x13 medical schools =

8

LARYNGIOSCOP SETS Basic Laryngoscope set, Macintosh folding pattern,with large handle to take, two R14

batteries,Satin chrome-plated brass with a knurled finish and with 3 blades; blades should

be autoclavable

9 ENDO-TRACHEAL TUBES CUFFED

ENDO-TRACHEAL TUBES CUFFED for training reusable

Thin-walled and flexible cuff

Standard 15 mm connector

Pilot balloon with self sealing valve

Graduation marks to aid correct positioning

Sizes : 4 sizes ID (Inside diameter),OD(Outside diameter),Length(including connector)

a)2.5 mm ,3.6 mm, 171 mm b)3 mm, 4.3 mm ,190 mm c) 5.5 mm 6.9 mm 274 mm d) 6.6mm 8.2 mm 317 mm

10 INTUBATION STYLET :

INTUBATION STYLET :To fit the Endothracieal tube with 4 sizes ID (Inside

diameter),OD(Outside diameter),Length(including connector) a)2.5 mm ,3.6 mm, 171 mm

b)3 mm, 4.3 mm ,190 mm c) 5.5 mm 6.9 mm 274 mm d) 6.6 mm 8.2 mm 317 mm

11 ENDOTRACHEAL TUBES UNCUFFED

ENDOTRACHEAL TUBES UNCUFF ED for training reusable

Smooth beveled and moulded a traumatic hooded tip

Graduation marks to aid correct positioning

Standard 15 mm connector

Clear material allows visualization of condensed exhaled air

Sizes : 4 sizes ID(Inside diameter);OD(Outside diameter);Length (including connector)

a)2.5 mm ,3.6 mm, 171 mm b)3. 3 mm 4.3 mm 190 mm c)5 5 mm 6.9 mm 274 mm d)6.5

mm 8.8 mm 327 mm

12 OXYGEN CYLINDER (12 litters)

OXYGEN CYLINDER SPECIFICATIONS :

Capacity: 12 Liter

O2 Regulator

O2 Humidifier

Adult mask

Infant mask

Nasal tube

O2 tubing

13RESUSCITATOR BAG (AMBO BAG) WITH

MASK (ADULT & PEDIATRICS) set

RESUSCITATOR BAG (AMBO BAG) WITH MASK (ADULT &PEDIATRICS) Set

SPECIFICATIONS :

Hand held silicon type.

Main unit consists of :

Pressure regulator with mask and plastic hood.

Face mask for child (3 pieces)

Face mask for adult (3 pieces).

Oxygen reservoir bag with safety valve (1 piece)

Oxygen feeding tube ( 4 pieces)

Including carrying bag.

Specifications :

Self inflating bag volume: approx 1600ml

Oxygen reservoir bag volume : approx 2600 ml , autoclavable

Materials:

Self inflating bag: semi.

Transparent silicon rubber.

Valve housing : transparent polysulfone

Shell of mask: transparent polysulfone.

Cushion of mask: transparent silicon rubber

14

SIMPLE OXYGEN MASK SIMPLE OXYGEN MASK

Medium concentration, barbed fittings to prevent patient disconnect, elastic strap,

adjustable nose clip,Reusable 10 adult size and 10 Pediatric size .

Adult with 7' tubing,

Pediatric with 7' tubing

15

CLEAR CURVED SOFT TIP NASAL PRONGS CLEAR CURVED SOFT TIP NASAL PRONGS

Clear curved pediatric cannula with 7' Sure Flow tubing, 50/case

Clear curved adult cannula with 7' Sure Flow tubing, 50/case

50 Adult suze, 50 pediatric size, preferabliy reusable

Company Name:




Telephone (Mobile):



15/23



Annex II


16

AIRWAY MANAGEMENT TRAINING

MANIKIN

AIRWAY MANAGEMENT TRAINING MANIKIN

Anatomically accurate adul t head and torso including (Adult and Pediatic size) two

form each size

oral cavity, oropharynx, larynx, trachea and lungs

Ability to confirm successful intubation by auscultation over intact chest wall

Reali stic tracheostomy traini ng, care, and suction ing

Surface should be washable with soap and water

.

17

CPR CHILD MANIKIN Child patient care mankin with rotatable arms and legs and articulating hand, allows

training of basic and advanced patient care. ~Weight :- 2.95kg

Dimensions :- 14 x 7 x 23

Descriptions :- Professional Child CPRAED Training Manikin (with CPR Monitor) with

6-8 Child ;Color Prefered Dark Skin; FaceShield LungBags, with English instruction

Sheet and a carrying case.

18

ADULT MANIKIN MALE Basic Adult patient care Manikin, Male features, full size adult with movable joints, as

well as soft fingers and toes, include IM, IV, Subcutaneous injections, soft hand for finger

prick, and stomies, allows basic & advanced patient care. Should be designed to deliver

comprehensive BLS training for professional rescuers.Should includes: 4 decorated Face

Skins, 3 disposable Airways, Carrying Case, Track Suit, and 50 Manikin Wipes.

19

ADULT MANIKIN FEMALE Basic Adult patient care Manikin, female features, full size adult with movable joints, as

well as soft fingers and toes, include IM, IV, Subcutaneous. injections,soft hand for finger

prick, and stomies, allows basic & advanced patient care. Should be designed to deliver

comprehensive BLS training for professional rescuers.Should includes: 4 decorated Face

Skins, 3 disposable Airways, Carrying Case, Track Suit, and 50 Manikin Wipes.

20









LOT 7

1

ADULT CARDIO-PULMONARY

RESUSCITATION TRAINING MANIKIN

ADULT CARDIO-PULMONARY RESUSCITATION TRAINING MANIKIN

Anatomically accurate full-body adult manikin with correct palpable

anatomical landmarks including :

Xiphoid process, ribs and nipple,disposable upper and lower airways

Head, neck and jaw should be fully articulated to allow for head tilt/chin lift and jaw

thrust maneuvers

Chest wall should allow for realistic chest compressions and simulate rise and fall during

ventilation

Sensors attached to manikin should be able to detect inflation volume and depth of chest

compression which is indicated to the performer via a monitor /performance indicator


2

INFANT CARDIO-PULMONARY

RESUSCITATION TRAINING MANIKIN

INFANT CARDIO-PULMONARY RESUSCITATION TRAINING MANIKIN

Anatomically accurate full-body infant size manikin with correct

palpable anatomical landmarks including

xiphoid process, ribs and nipple, disposable upper and lower airways & palpable

simulated

carotid pulse


thrust maneuvers

Chest wall should allow for realistic chest compressions

Sensors attached to manikin should be able to detect inflation volume and depth of chest

compression which is indicated to the performer via a monitor /performance indicator


Company Name:




Telephone (Mobile):



16/23



Annex II


3BASIC LIFE SUPPORT MANIKIN WITH

INDICATOR

BASIC LIFE SUPPORT MANIKIN WITH INDICATOR

Should have natural obstruction of the airway to allows students to learn the important

technique of opening the airway so that in real-life situation they know how to effectively

administer air to the victim.

Head tilt/chin lift or jaw thrust should be there to allows students to correctly practice

airway maneuvers necessary when resuscitating a real patient.

It should provide realistic chest rise to verify correct ventilations.

Realistic resistance for chest compressions should be there to allows the students to

experience the amount of pressure needed to perform proper chest compressions in a real-

life situation.

Anatomically correct landmarks and sternal notch allow the student to practice

identification of all anatomical landmarks relevant to CPR

Ceratoid pulse must be there to simulate realistically check for pulse.

Provided with disposable non-rebreathing airways. Face mask are suitable for use by

more than one student during class and are quick and easy to change after each training

session.

Skill Guide CPR performance indicator provides immediate objective feedback on

correct inflation volume, excessive inflation, too fast inflation, correct compression depth,

excessive compression and in correct hand position.

Must have hard carrying case.

Cleaning kit should be provided for easy cleaning after

4

ADULT CARDIO-PULMONARY

RESUSCITATION DEFIBRILLATION

MANIKIN

ADULT CARDIO-PULMONARY RESUSCITATION DEFIBRILLATION

Anatomically accurate full-body adult manikin with correct palpable

anatomical landmarks including :

xiphoid process, ribs and nipple, disposable upper and lower airways and automatically

generated carotid pulse


thrust maneuvers

Cardiac rhythm simulator should generate various rhythm patterns which also responds

to defibrillation

The training system should be able to work with all types of defibrillators

Chest wall should allow for realistic chest compressions

Sensors attached to manikin should be able to detect inflation volume and depth of chestcompression which is indicated to the performer via a monitor /performance reporting

system

Performance reporting system should provide printed feedback to performer


5THRACIOSTOMY TUBE Thraciostomy Tube with rotating lock (Metalic), sizes 5, 7 ,and 8, stainles steel, 3

from each size 3x3=9

6

MULTIPURPOSE ADULT AIRWAY TRAINER

MANIKIN (tracheostomy, cricothyrotomy, and

pneumothorax decompression)

MULTIPURPOSE ADULT AIRWAY TRAINER

Should have anatomically accurate features enable extensive training in a variety of

airway techniques.

Fully articulated to allow head tilt/chin lift

Soft neck with cricocartilage permits classic Sellick maneuver

18mm airway permitting passed of cuffed ET tube or EOA

Adult airway management trainer

Students learn oral and nasal techniques for opening airways

All ows train ing f or tr acheostomy, cricothyrotomy, and pneumothorax

decompression

Includes 6 neck collars, 3 cricocartilages, and membrane tape

Includes trainer carrying bag

7

CHEST TUBES CHEST TUBES 5 from Each size

Chest Tubes (Reusable) With Trocar Size 12.

Chest Tubes (Reusable) With Trocar Size 14,

Chest Tubes (Reusable) With Trocar Size 22

Chest Tubes (Reusable) With Trocar Size 26

8Water seal chest drainage set & chest tube Chest aspirating set with 2 drainage bottle , tubing,and with aspirating needle of 2 way

Luer lock stopcock 16gx3" and 18gx3"

9

PNEUMOTHORAX MANAGEMENT

TRAINING MANIKIN

PNEUMOTHORAX MANAGEMENT TRAINING MANIKIN

Anatomically accurate torso with encased ribs

Replaceable chest wall which can be used for a minimum of 20 incisions both in mid-

axillary and subclavian sites

Pleural cavity and lungs with bilateral tension pneumothorax which can

be decompressed


Company Name:




Telephone (Mobile):



17/23



Annex II


10

THORACENTHESIS NEEDLE THORACENTHESIS NEEDLE, hypodermic,1.6x100mm,luer with stop cock and tubing

for drainage

11

DEFIBRILLATOR DEFIBRILLATOR

TECHNICAL SPECIFICATIONS

Biphasic, Manual and AED with voice prompt, compact and light weight

Energy selection 5J to 200J in steps.

Momentary energy selection access on front panel.

Should have adult and pediatric paddles integrated on same handle.

Momentary charge key on front panel and on the apex hand.

Monitor should display selected and delivered energy

Should have disarm facility.

Energy should be delivered within 30ms after the detected R wave in

synchronization mode.

Charging time maximum 5 sec for 200J.

Should have battery backup for 50 discharges of 200J.

Should supply three pairs of AED pads

Should operate on mains 230V, 50Hz

Should have safety certificate from a competent authority CE / FDA (US) /

12

ELECTROCARDIOGRAM 12 LEAD ELECTROCARDIOGRAM 12 LEAD with accessaries

SPECIFICATIONS : Leads: 12 standard leads acquired simultaneously and continuously

Three real times continuous with rhythm, interpretation and measurementsAdult and

Pediatric

writer speed : 5,10,25 or 50mm/sec

LCD display : backlit graphic display around 5

display channel:1, 3, 6 ,12

operation modes : Auto or Manual

Copy button for generating multiple copies

Thermal printer

Rechargeable battery

Battery power capacity not less than two hours

Power:220V AC 50/60Hz

Cart Is included

Cable holder is included

ECG cable

Limb electrodes 4

Chest pump electrodes 8

Jell tube 5

ECG paper roll10, with additional spare batteries, power must be country standard

220V/50Hz

13

PUlSE OXYMETER Technical Specifications

Pulse Oximetry

Range: 0% to 99%

Resolution: 1%

Accuracy: 70% to 99% range: 2%

Method: Dual wavelength LED

Heart (Pulse) Rate

Range: 20 to 300 bpm Resolution: 1 bpm

Accuracy: 1 bpm or 1%, whichever is greater

Alarms

Indication: Audible, visual (EN475); adjustable volume

Silence: Temporary (2 minutes) and Permanent

Parameter/Range: High Saturation: 70% to 98% or Off;

Defaults: Off

Low Saturation: 30% to 99% or Off at 85%

Company Name:




Telephone (Mobile):



18/23



Annex II


14 Male Uretheral/Suprapubic Catheterization Trainer

Manikin

Male Catheterization Simulator for Skills of Catheter insertion Urtthral /Suprapubic

Anatomically accurate model of the male pelvis including bladder,

penis, urethra with mucosal folds, bulbous urethra & internal sphincter,without the legs

.The suprapubic bone should be visable.

A pressurised fluid system should allow for fluid/ urine flow when

catheter enters bladder

Urethra and sphincter should provide a realistic tactile sensation to the

performer.

A rubber catheter 16 CH is supplied with each male trainer

A rubber catheter 14 CH is supplied with each female trainer

A kidney dish, lubricant application and bladder syringe are supplied with each trainer

A suprapubic skin pad with bladder plug is supplied with each trainer

Bladder pressure can be altered


15

Female Uretheral/Suprapubic Catheterization

Trainer

Female Catheterization Training Simulator

Female Catheterization Simulator for Skills of Catheter insertion Urethral /Suprapubic

Anatomically accurate model of the female pelvis including features of the female

genitalia without legs .The supra-pubic bone should be visible. A pressurized fluid system should allow for fluid/ urine flow when catheter enters

bladder

When the catheter reaches the bladder, urination should be simulated.(e.g. Water)

Urethra and sphincter should provide a realistic tactile sensation to the

performer.

A suprapubic skin pad with bladder plug is supplied with each trainer

The simulator should allow bladder pressure changes.

The transparent urethra and the bladder models should allow through the transparent

walls, facilitating anatomical comprehension.


16Rectal tube Tube rectal: Child size #12 - #14 & Adult size #14 - #24, open tip one eye, funnel end,

sterile, reusable, rubber. 130 from child and adult sizes. Total 260 rectal tubes

17

Naso-gastric Tube (Adult and Ped) Pediatric: Tube, gastric feeding size ch 8 infant, 380mm long, distal end with 2 windows,proximal end with protective lid, anatomical marking, sterile, reusable Adult: Tube, nasal

feeding, size ch 16,400mm, open tip, one eye, funnel end, open tapered end to

accommodate funnel, reusable, soft rubber, non-sterile supplied with funnel. 195 from

each size. Total 390 tubes

18

DIGITAL PROSTATE EXAMINATION

TRAINING MODEL

DIGITAL PROSTATE EXAMINATION TRAINING MODEL

Accurate anatomical model of the male pelvis including:

buttocks, anus, rectum and prostate, mounted in the left lateral position

Anus, rectum and prostate should have a realistic feel allowing the examiner to

appreciate the surface features, consistency and size of these organs

The prostate should be detachable and interchangeable allowing simulation of various

clinical scenarios including normal prostate, benign hypertrophy and carcinoma

Several rectal conditions should also be simulated


19

Peritoneal biopsy needle Specification: #25 (12G) L 85mm

Description: Used for puncturing human peritoneal, hooking up peritoneum biopsy and

cell tissue.

20

LUMBAR PUNCTURE SIMULATION MODEL LUMBAR PUNCTURE SIMULATION MODEL

Set includes:

1 Lumbar region model

6 Puncture blocks: 2 normal CSF, 1 obesity CSF, 1 senior CSF, 1 senior obesity CSF, 1

epidural

1 Lumbar region skin cover

3 Lumbar region support bases: sitting position, lateral position, team teaching

1 Lumbar spine model

1 set of irrigator bag, tube, support base and syringe

1 Guidebook in English

21LUMBAR PUNCTURE NEEDLE LUMBAR PUNCTURE NEEDEL 18G, 21G Reusable stainles steel 10 from each size

22









LOT 8

Company Name:




Telephone (Mobile):



19/23



Annex II


1

INJECTION TRAINING PAD INJECTION TRAINING PAD

Realistic soft tissue layers including epidermis, dermal, sub dermal and muscle layers

Pad should allow intr a-dermal, subcutaneous and in tra-muscular i njection

techniques

Pad should have a curved lifelike profile

2

VENEPUNCTURE TRAINING PAD VENEPUNCTURE TRAINING PAD

Strap on pad with realistic soft tissues layers with at least three palpable and infusible

veins

Veins should have self-sealing characteristics which will allow for repeated penetration

Veins should be connectable to a blood reservoir system which simulates blood flow

3

VENEPUNCTURE TRAINING MODEL HAND VENEPUNCTURE TRAINING MODEL HAND

Anatomically accurate adult hand

with skin and palpable & infusible dorsal veins

Pad should contain at least three vein of differing sizes including a paediatric size

Skin and vein system should be replaceable


There should be realistic flashback of blood following intravenous penetration


4

PERIPHERAL INTRAVENOUS THERAPY

TRAINING ARM MODEL

PERIPHERAL INTRAVENOUS THERAPY TRAINING MODEL

Anatomically accurate arm with

palpable and infusible cephalic, median cubital, basilic and dorsal veins & palpable radial

artery

Skin and vessels should be replaceable

Skin should be allow realistic feel during procedures


There should be realistic flashback of blood following intravenous

penetration

Radial artery should have realistic pressure allowing for flashback durin arterial

puncture


5

SURGICAL DISSECTION PAD (SMALL) SURGICAL DISSECTION PAD (SMALL)

Realistic multilayered soft tissue pad including at least 4 vessels

(veins, arteries and capiiliary vessels) which should allow for a wide variety

of incisions, dissection, ligation, suturing & stapling

Should be designed to provide a realistic sensation during procedures

6

SURGICAL DISSECTION PAD (Large ) SURGICAL DISSECTION PAD (Larg )

Realistic multilayered soft tissue pad including at least 10 vessels

(veins, arteries and capiiliary vessels) which should allow for a wide variety

of incisions, dissection, ligation, suturing & stapling

Should be designed to provide a realistic sensation during procedures

7

WOUND CLOSURE TRAINING PAD WOUND CLOSURE TRAINING PAD

Realistic soft tissue layers including epidermis, dermal and subdermal layers which should

allow for a wide variety of

incisions,

simple & advanced suturing techniques,

stapling and use of skin adhesives Skin pad should provide realistic tactile sensation to

the trainee

All layers should provide realistic retention of sutures

Pad should be mountable on a jig

8 FETOSCOPE Fetoscope, foetal, Pinard, monaural, unbreakable plastic

9VAGINAL SPECULUM (bivalve) Larg sized: Vaginal speculum (bivalve) Graves, large 115mmx35mm, bi-valve

(Duckbill), stainless steel,

10Vaginal Speculum medium size Medium sized : Vaginal speculum(bivalve) Graves, medium 1 3/8 "x4 ''bivalve

(Duckbill),stainless steel,

11 Vaginal Speculum small size Small size : Vaginal speculum(bivalve) Graves, small, 75mmx20mm, bi-valve(Duckbill), stainless steel,

12FEMALE PELVIC EXAMINATION TRAINING

MODEL

FEMALE PELVIC EXAMINATION TRAINING MODEL

Anatomically accurate model of the female pelvis & perineum including:

external genitalia, urethra, vagina, cervix, anus and rectum

Model should allow for the insertion of different uterine assemblies

simulating different pathologies

Model should be designed to allow digital examination, bimanual examination, speculum

insertion, cervical smear procedure, catheterization,and digital rectal examination

procedures

The perineal skin, labia, vaginal surface, cervix, anus and rectum should provide a

realistic tactile sensation of the consistency and texture of these organs & tissues


Company Name:




Telephone (Mobile):



20/23



Annex II


13

Birth simulator The simulator should enables

Instructors to effectively teach the complexities associated with birthing.

Participants can experience childbirth and practice the skills required for successful

deliveries.

Should have detachable abdominal and perinea skin enables visualization of internal

maneuvers and fetal positioning during training.

learners to see how maneuvers affect the fetus in-utero.

force monitoring provides a visualization tool for proper assisted delivery.

learners see and feel the appropriate force required with hands on experience and

feedback.

Articulating baby should be presented in multiple positions to represent difficult and

routine deliveries

Product should have the following Featuers

Anatomically accurate perineum and pelvic floor muscles, with bony pelvis .

The abdominal skin should be removed to display anatomical structures and fetal

positioning

Representative full term baby with:

o Palpable fontanel and suture lines

o Palpable clavicles and scapulae

o Detachable placenta with cord

Mother allows for multiple delivery positions and techniques:o Normal delivery

o Breech delivery

o Vacuum delivery

o Shoulder dystocia management

o Forceps delivery

14

Episiotomy suturing simulator EPISIOTOMY REPAIR TRAINING MODEL

Anatomical accurate model of the female perineum with external genitalia,

Vagina and cervix inclusive of vaginal mucosa,

Annex II-Technical Specifications

Documents

Transcript of Annex II-Technical Specifications