AMT756 2012 Corvette Coupe Instruction Sheet Outer EN · imperfections and repeat the procedure if...
Transcript of AMT756 2012 Corvette Coupe Instruction Sheet Outer EN · imperfections and repeat the procedure if...
Completed Assembly
Apply Decal
3
Assembly Sequence
RECOMMENDED PAINT COLORS
SYMBOLS
AluminumGloss Black
SilverSemi-Gloss BlackSemi-Gloss Grey
Flat BlackWhite
Part Number49
1/25 SCALE
A756-200
DECALS: See back of instruction sheet for application instructions. Many of the very small decals in this kit have been included in duplicate to serve as backups, should any get lost or otherwise compromised during application.
REFER TO BOX ART PHOTOS FOR PAINTING DETAILS
1. DETAILING DECALS
DECALS MUST BE APPLIED TO CERTAIN PARTS AFTER PAINTING BUT PRIOR TO ASSEMBLY. SEE SECTION 1.
5. BODY
6. FINAL ASSEMBLY
BLACK METAL SCREWS (4)
20RIGHT FOG
LIGHT BEZEL
19LEFT FOG
LIGHT BEZEL
32LEFT FOG
LIGHT LENS(Clear)
31RIGHT FOG LIGHT LENS
(Clear)
9HOOD
8REAR FASCIA
28
30
29
27
TAILLIGHT LENSES (4) (Clear)
14LEFT MIRROR
15RIGHT MIRROR
23WINDSHIELD (Clear)
7FRONT FASCIA
18RIGHT LIGHT
UNIT
1COUPEBODY
26RIGHT HEADLIGHT
LENS (Clear)
25LEFT HEADLIGHT
LENS (Clear)
Carefully install completed chassis/interior assembly into completed body. Ensure chassisis fully seated, then using a small Phillips screwdriver, install screws into the 4 locations shown.
IMPORTANT: Apply decals to seats, dashboard and steering wheel BEFORE assembling parts in Section 3/INTERIOR.BE SURE TO PAINT THE DESIRED PARTS FIRST AND ALLOW THEM TO DRY FULLY BEFORE APPLYING DECALS.DECAL
DECALS: See back of instruction sheet for application instructions. All decals have been included in duplicate to serve as backups, should any get lost or damaged during application.
10 STEERING WHEEL 12 DASHBOARD
SEATS (Vinyl)
(HVAC DECAL)
OPTIONS
17LEFT LIGHT UNIT
(Repeat for other side.)
NOTE: Locate holes in top of windshield to pins inside roof of body.
Apply Corvette® emblem decals to front and rear fascias, as shown. Apply GM logo decals to rear quarter panels using box art photos for placement detail. Apply your choice of rear license plate decal.
NOTE: Open sides of fog light bezels face out.
20122012
(Other side.)
(Other side.)
GENERAL MOTORS Trademarks used under license to Round 2, LLC. AMT is a registered trademark. ©2011. All rights reserved. Round 2 & design is a trademark of Round 2, LLC. ©2011 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved.
Round 2, LLC 4073 Meghan Beeler CourtSouth Bend, IN 46628
International Hobbycraft (UK) Ltd.21 St. Thomas StreetBristol BS1 6JS England
DECAL APPLICATION INSTRUCTIONS1. Cut decals apart close to image. Apply one at a time.2. Dip decal into tepid water until paper backing loosens.3. Moisten area of model where decal is to be applied, to aid in positioning.4. Slide decal partly off of paper backing.5. Place decal on model face up and slide paper backing away.6. Thoroughly blot out excess water, air bubbles, and any excess emulsion with soft, lint-free cloth.7. Allow time to dry before handling.
NOTE: If air bubbles or wrinkles form on an irregular or curved surface, cut decal and press into place.
Decal
Paper Backing
DECAL
1
DECAL
1
DECAL
8
DECAL
9
DECAL
17DECAL
10
DECAL
DECAL
12
DECAL
10
DECAL
11
DECAL
13
DECAL
16
DECAL
14DECAL
15
DECAL
2DECAL
3
DECAL
4
DECAL
5
IMPORTANT
Assembly: Carefully study and understand the entire instruction sheet. Compare the parts in the box to the instruction sheet to be sure you have received all the parts required. Carefully remove parts from trees. Before cementing, "TEST FIT" parts together to insure proper location and alignment. Scrape paint and plating from surfaces to be cemented. Subassemblies and components should be painted before any parts are attached. Use only cement and paint made for styrene plastic.
Painting: Wash parts thoroughly with mild soap and water. Parting lines, glue joints, and sharp edges should be sanded or filled with filler putty designed for plastic. Apply a "primer" coat and allow to dry. Check parts for imperfections and repeat the procedure if necessary. Remove any lint or dust. Apply paint evenly, in several thin coats rather than one heavy coat. Allow each coat to thoroughly dry before the next is applied. Each coat should be carefully “wet sanded” using slightly damp No. 1200 sandpaper. Be careful not to remove any detail while sanding. Lightest colors should be painted first. Use frosted tape to mask off areas not to be painted. Remove tape after paint is dry to the touch. Use a very fine brush to touch up edges.
Decals: See back of instruction sheet for proper application. Decals should to be added after applying a gloss coat. Apply a final clear coat after decals are dry.
2. WHEELS & CHASSIS
4. INTERIOR TO CHASSIS
37RIGHT FRONT DISC BRAKE 39
RIGHT REAR DISC BRAKE
36LEFT FRONT DISC BRAKE
38LEFT REAR DISC BRAKE
16EXHAUST TIPS (2)
21FRONT WHEEL (Chrome)
21FRONT WHEEL (Chrome)
22REAR WHEEL (Chrome)
(LARGE / WIDE)
22REAR WHEEL (Chrome)
(LARGE / WIDE)
IMPORTANT: Apply decals to seats, dashboard and steering wheel as shown in SECTION 1, before assembling parts.
METAL AXLE METAL AXLE
TAB
REAR TIRE (LARGE / WIDE)FRONT TIRE (SMALL)
FRONT TIRE (SMALL)REAR TIRE (LARGE / WIDE)
CHASSIS SHOWN UPSIDE DOWN
NOTE: Work completed wheels firmly onto axles.
NOTE: Wheels not shown for clarity.
Locate interior to chassis by inserting pins on top side of chassis into large bosses in bottom of interior.
NOTE: Ensure correct disc brake part numbers are used for each wheel. Each disc brake has a tab which locks into the chassis, to position its caliper correctly. Apply cement to tabs only, so that axles may rotate inside.
TAB
TAB TAB
10
11
NOTE: To make the tires easier to stretch, run them under very warm water for 30 seconds. BE CAREFUL NOT TO BURN YOUR HANDS.
Stretch tire over wheel making sure it is fully seated.
10STEERING
WHEEL
11COLUMN
12DASHBOARD
4FLOOR PAN
SEATS (2) (Vinyl)
5LEFT DOOR PANEL
6RIGHT DOOR PANEL
NOTE: Locate tab on bottom ofdashboard to slot at front of
floorboard tunnel.
13SHIFTER
KNOB(To hole)
3. INTERIOR
2(Completed Chassis)
3(Completed Interior)
DECAL
6
DECAL
7