Alfacubic- Alfa Laval[1]
-
Upload
harmonia-msanchez -
Category
Documents
-
view
231 -
download
0
Transcript of Alfacubic- Alfa Laval[1]
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 1/24
Product manual air heat exchangers
Refrigeration and HVAC Cooling
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 2/24
Cubic Line/Single Air Discharge General Contents
.
kyCubic Line/Single Air Dischargeky General Contents
General FeaturesMost of our unit coolers are available in the following versions:
• Direct expansion evaporators
• Brine unit coolers
• Pump ammonia evaporators
Certifications and reliability All DX u nit coolers are guaranteed by Eurovent "Certify All". Alfa
Laval quality systems fully comply with ISO 9001, and all of our
products are manufactured in strict accordance with CE regulations.
Fin spacingIn our experience, fin spacing should correspond to both the goods
stored and the room’s air temperature, as follows:
Series Green Line Red Line B lue Line
Product Fruit /Vegetables
Meat / Fish Frozen food
Room temperature 10 ÷ 0°C 0 ÷ -7°C -18 ÷ -25°C
Fin spacing 3 ÷ 4,5mm 5 ÷ 6mm ≥ 7-12mm
CapacityThe standard conditions are in accordance with EN 328. The cooling
capacities stated in the catalogue are the nominal capacities for
Qn (wet conditions), in compliance with Eurovent regulations. In
standard Qst conditions (dry), the nominal capacities are calculatedwith the following formula:
Qn = Qst x Wet Coil Factor
Standardconditions
Air InletTemp °C
EvaporationTemp. dewpoint) °C
R.H.Wet CoilFactor
SC1 10 0 85% 1,35
SC2 0 -8 85% 1,15
SC3 -18 -25 95% 1,05
SC4 -25 -31 95% 1,01
The nominal capacities are calculated with refrigerant R404A. For
different refrigerants the following factors should be applied:
Refrigerant SC1 SC2 SC3 SC4R134a 0,93 0,91 0,85 -
R22 0,95 0,95 0,95 0,95
R507 0.97 0.97 0.95 0.95
R404A 1 1 1 1
See the fin material factors below:
Fin material Factor
Aluminium 1
Coated Aluminium 0,97
Copper 1,03
Relative humidity ΔTThe cold room hygrometric conditions are defined by the room
temperature and the working ΔT. At positive cold room temperatures
ΔT has an influence on the relative humidity (RH).
Air throw
Air throw (L)=air velocity limit 0.25m/s.
The values given in the tables are based on an air temperature of
20°C beneath a flat ceiling with no obstructions. The height and
air circulation of the room can influence the air throw. The stated
distances are based on a final air velocity of 0.25m/s.
FansSingle-phase motors 230V-50Hz, or three phase 400V-50Hz,
protection class IP54 according to DIN 40050. Integrate thermal
protection by thermo contact. Provide reliable protection against
thermal overload.
T [°C] 20 10 0 -10 -15 -20 -25 -30
Fc 1 1,04 1,08 1,12 1,14 1,16 1,18 1,2
Data SoundOverall sound level Lp (ref. 2x10-5Pa) is the average calculated
A-weighed sound level at the surface of a 3mt parallelepiped
envelope (EN13487). Sound Level data is presented for comparative
purpose only.
m 1 2 3 4 5
dB A) 6 4 2 1 0
Defrost All our coolers come equipped with several different defrosting
systems. For room temperatures where ice build-up is likely, and
where the ambient room temperature is below 0°C, a unit with a
defrosting system is needed
18The PM A is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 3/24
Cubic Line/Single Air Discharge General Contents
Test and cleaningThe coils are cleaned and dehydrated in order to remove any traces of oil. Each heat exchanger undergoes a pressure and leak test with dry
air at 34 bar, before being supplied with a nitrogen pre-charge.
Guarantee All our products are protected under warranty for 24 months from the factory shipping date. In the unlikely event o f a defect occurring within
the warranty period, please return the equipment or faulty part free of charge to us, where we will decide whether to repair or replace the
goods . Unfortunately, We cannot take responsibility for damage caused by the misuse or incorrect installation of our products. Brochure
subject to technical changes without prior notice
AlfaSelect Air
19The PM A is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 4/24
AlfaCubic Product Description
.
ky AlfaCubicky Product Description
.
ApplicationsCommercial unit coolers designed for use in small and medium cold
rooms from 10 up to 400 m³. Models designed for easy maintenance
with immediate access to inspection areas. This series is available
as evaporator (DX or pump, H(C)FC, NH3 and CO2) and brine unit
cooler. A sub-selection of models is available from stock.
Refrigerant all H C)FC,ammonia, brine, CO2*
Capacity (SC2) 1.5 up to 60kW
Air volume 1527 up to 30350 m3/h
* CO2 only for fan diameters 400 & 500 mm
Standard Configuration• Finned coil
• H(C)FC Inner grooved Cu tubing ø 12 mm, triangular tube
pitch
• Brine Smooth Cu tubing ø 16 mm, triangular tube pitch
• NH3 + CO2 Smooth stainless steel tubing ø 16 mm, triangular
tube pitch
• Corrugated Alu-fins- Fin spacings 4, 5.5, 6, 7, 8, 10 and 11 mm
• 1 to 4 Fans, ø 250 mm up to ø 500 mm, drawing trough the coil.
2-Speed fan motors 400/50-60/3 or 230/50-60/1 (fan ø 500 mm
only), two noise levels (Δ/Y).
• 6 poles, 230/1 (ø 350, 400 & 500 mm)
• 4 poles, 400/3 (all models)
• 6 poles, 400/3 (ø 400 & 500 mm
Motors with dynamically and statically balanced external rotors,manufactured in accordance with VDE 0530/12.84 IP54 class F.
Integrated thermo contacts (Clickson) provide reliable protection
against thermal overload.
• Corrosion resistant materials: coil frame AluZinc, casing
pre-painted aluminium RAL 9010 with a protective plastic film (to
be removed after installation).
• Hinged drip tray for easy installation and maintenance.
• Fitted with schräder valve on the suction connection for testing
purposes.
• Suitable for dry expansion or pumped system.
• Stickers indicate fan direction and refrigerant in/out.
• Delivery in mounting position. Coolers are mounted on wooden
beams. Installation can take place with use of a forklift.
Typical application
Series GL RL BL
Product Fruit/vegetables Meat/fish Frozen food
Room temperature 10÷0ºC 0÷-7ºC -18÷-25ºC
Standard finsspacing DX (mm)
4 5.5,6 7,8,10,11
Design PressureDesign pressure 34 bar (H(C)FC/ammonia, 50 bar (CO2) or 9 bar
(brine). Higher design pressures on request. Each heat exchanger
is leak tested with dry air and finally supplied with a nitrogenpre-charge.
SelectionSelection and pricing is to be performed with our Alfa Laval air heat
exchanger selection software. Selection output includes all relevant
technical data and dimensional drawings. Please contact our sales
organization for details and full technical documentation.
Benefit• Wide & versatile cooler range, designed for all working conditions.
• Advanced product selection software available.
• Low noise level.
• Reliable performance, Eurovent certified.
• Stock range available
• Energy efficient.• Low total cost of ownership.
• Two-year product guarantee.
20The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 5/24
AlfaCubic Product Description
Option• Defrost systems
• Electric defrost (E)
• Hotgas defrost in coil & driptray (HG)
• Hotgas defrost + electric in driptray (HG + HD)
• Heater driptray (HD)
• Driptray insulation (IS)Not combined with electric defrost
• Fan ring heater (FH)• Re-heating coil (RH)
• Fan motors wired to a terminal box (CB)
• Safety switch (SW)
• Stainless steel 304 casing & coil frame (SS)
• Epoxy coated fins (EP)• Coil cataphoresis treatment (CF)
• Air sock adapter ring (SR), ø 400 & 500 mm only
• AlfaStreamer (ST), ø 400 & 500 mm only
21The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 6/24
AlfaCubic Technical Data
Air Throwm
Conn. Sizemm
TotalPower
W
TotalCurrent
ARPM
Description
Finspac-ingmm
Capacity*SC2kW
Ca-pacity*SC3kW
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVolume
dm3
Fanmotors
230V/1ph/50Hz
PoleNoisedB A)Lp A) Inlet Outlet
Weightkg
GLEH251A 4 1.98 1.57 1435 13.3 - 12.81 1.3 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 19
GLEH251B 4 2.52 2.06 1371 12.83 - 19.22 2 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 21
GLEH252A 4 3.99 3.19 2870 15.04 - 25.63 2.7 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 31
GLEH252B 4 5.14 4.16 2742 14.56 - 38.44 4 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 36
GLEH253A 4 5.99 4.51 4306 16.05 - 38.44 4 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 45
G LE H2 53 B 4 7.75 5.96 4113 15.58 - 57.67 6 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 51
GLEH351A 4 3.25 2.62 2375 16.32 - 21.36 2.2 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 35.1
GLEH351B 4 4.20 3.25 2219 15.51 - 32.04 3.4 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 43.1
GLEH352A 4 6.64 5.23 4749 18.75 - 42.72 4.5 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 52.2
GLEH352B 4 8.28 6.16 4438 17.93 - 64.07 6.7 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 59.2
GLEH353A 4 9.99 7.75 7124 20.17 - 64.07 6.7 3x350 450 1.98 1400 4p 54 1/2"SAE 28mm 73.3
GLEH353B 4 12.66 9.67 6657 19.35 - 96.11 10.1 3x350 450 1.98 1400 4p 54 5/8"SAE 28mm 82.3
GLEH354A 4 13.31 10.25 9498 21.17 - 85.43 9 4x350 600 2.64 1400 4p 55 5 /8 "S AE 3 5m m 1 04 .4
GLEH354B 4 16.72 12.55 8876 20.36 - 128.1 13.4 4x350 600 2.64 1400 4p 55 5 /8 "S AE 3 5m m 1 08 .4
GLEH401B 4 5.91 4.66 3178 19.01 38.02 43.83 4.6 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 50.7
GLEH401C 4 6.72 5.12 3014 18.25 36.5 58.44 6.1 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 55.7
GLEH402B 4 12.06 9.31 6403 21.89 43.78 89.96 9.4 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 101.4
GLEH402C 4 13.79 10.65 6081 21.15 42.3 119.9 12.6 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 106.4
GLEH403B 4 18.16 13.90 9626 23.54 47.08 136.1 14.3 3x400 480 2.19 1430 4p 56 22 42mm 137.1
GLEH403C 4 20.65 15.67 9148 22.81 4 5.62 181.5 19 3x400 480 2.19 1430 4p 56 22 42mm 147.1
GLEH502A 4 18.04 12.88 15290 37.08 7 4.16 107 11.2 2x500 1360 6 1300 4p 58 16 35mm 135
GLEH502B 4 24.15 18.02 14560 35.74 71.48 160.5 16.8 2x500 1360 6 1300 4p 58 22 35mm 154
GLEH502C 4 28.05 21.00 13880 34.49 68.98 214 22.4 2x500 1360 6 1300 4p 58 22 42mm 172
GLEH503B 4 36.04 26.42 21880 37.81 75.62 242.2 25.4 3x500 2040 9 1300 4p 60 22 42mm 218.5
GLEH503C 4 42.38 31.82 20860 36.56 73.12 322.9 33.9 3x500 2040 9 1300 4p 60 28 42mm 235.5
GLEH504B 4 48.32 35.61 29190 39.27 78.54 323.9 34 4x500 2720 12 1300 4p 61 28 54mm 279
GLEH504C 4 56.71 42.69 27840 38.03 76.06 431.9 45.3 4x500 2720 12 1300 4p 61 28 54mm 327
RLEH251A 5.5 1.64 1.31 1455 13.45 - 9.457 1.3 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 18
RLEH251B 5.5 2.13 1.75 1403 13.07 - 14.19 2 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 20
RLEH252A 5.5 3.29 2.66 2911 15.19 - 18.91 2.7 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 30
RLEH252B 5.5 4.37 3.55 2806 14.8 - 28.37 4 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 35
RLEH253A 5.5 5.04 3.88 4366 16.2 - 28.37 4 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 44
RLEH253B 5.5 6.71 5.22 4209 15.82 - 42.56 6 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 49
RLEH351A 5.5 2.68 2.17 2427 16.6 - 15.76 2.2 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 34.1
RLEH351B 5.5 3.63 2.85 2295 15.91 - 23.64 3.4 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 41.1
RLEH352A 5.5 5.52 4.40 4853 19.02 - 31.52 4.5 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 50.2
RLEH352B 5.5 7.29 5.51 4590 18.33 - 47.28 6.7 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 57.2
RLEH353A 5.5 8.36 6.57 7280 20.44 - 47.28 6.7 3x350 450 1.98 1400 4p 54 1/2"SAE 28mm 71.3
RLEH353B 5.5 11.04 8.55 6886 19.75 - 70.93 10.1 3x350 450 1.98 1400 4p 54 5/8"SAE 28mm 80.3
RLEH354A 5.5 11.18 8.73 9707 21.45 - 63.05 9 4x350 600 2.64 1400 4p 55 5/8"SAE 35mm 102.4
RLEH354B 5.5 14.69 11.19 9181 20.76 - 94.57 13.4 4x350 600 2.64 1400 4p 55 5/8"SAE 35mm 106.4
RLEH401B 5.5 5.07 4.04 3269 19.42 38.84 32.34 4.6 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 45.7
RLEH401C 5.5 6.00 4.64 3120 18.74 37.48 43.12 6.1 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 50.7
RLEH402B 5.5 10.43 8.16 6578 22.29 44.58 66.39 9.4 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 93.4
RLEH402C 5.5 12.31 9.60 6289 21.63 43.26 88.52 12.6 2x400 320 1.46 1430 4p 54 5/8"SAE 35 mm 1 01 .4
RLEH403B 5.5 15.77 12.23 9887 23.94 47.88 100.4 14.3 3x400 480 2.19 1430 4p 56 22 42mm 131.1
RLEH403C 5.5 18.55 14.25 9458 23.28 46.56 133.9 19 3x400 480 2.19 1430 4p 56 22 42mm 142.1
RLEH502A 5.5 15.30 11.30 15410 37.3 74.6 78.97 11.2 2x500 1360 6 1300 4p 58 16 35mm 169
RLEH502B 5.5 20.87 15.89 14740 36.07 72.14 118.4 16.8 2x500 1360 6 1300 4p 58 22 35mm 186
RLEH502C 5.5 24.94 18.95 14080 34.86 69.72 157.9 22.4 2x500 1360 6 1300 4p 58 22 42mm 201
RLEH503B 5.5 31.27 23.47 22140 38.13 76.26 178.7 25.4 3x500 2040 9 1300 4p 60 22 42mm 245.5
RLEH503C 5.5 37.65 28.68 21180 36.95 73.9 238.3 33.9 3x500 2040 9 1300 4p 60 28 42mm 258.5
RLEH504B 5.5 41.86 31.57 29540 39.58 79.16 239 34 4x500 2720 12 1300 4p 61 28 54mm 316
RLEH504C 5.5 50.36 38.43 28260 38.41 76.82 318.7 45.3 4x500 2720 12 1300 4p 61 28 54mm 359
*Nominal capacity according to ENV328 and Eurovent regulations (refrigerant R404A,ΔT=T INair -Tev).SC2: TINair =0°C, Tev=-8°C.SC3: TINair = -18°C, Tev=-25°C.Use external equalized thermostatic expansion valve.
22The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 7/24
AlfaCubic Technical Data
Air Throwm
Conn. Sizemm
TotalPower
W
TotalCurrent
ARPM
Description
Finspac-ingmm
Capacity*SC2kW
Ca-pacity*SC3kW
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVolume
dm3
Fanmotors
230V/1ph/50Hz
PoleNoisedB A)Lp A) Inlet Outlet
Weightkg
BLEH251A 7 1 .40 1.13 1467 13.54 - 7.538 1.3 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 17
BLEH251B 7 1 .85 1.52 1423 13.21 - 11.31 2 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 19
BLEH252A 7 2 .82 2.29 2935 15.27 - 15.08 2.7 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 28
BLEH252B 7 3 .82 3.12 2846 14.95 - 22.61 4 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 33
BLEH253A 7 4 .37 3.40 4402 16.29 - 22.61 4 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 42
BLEH253B 7 5 .92 4.65 4269 15.96 - 33.92 6 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 47
BLEH351A 7 2 .30 1.87 2458 16.76 - 12.56 2.2 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 32.1
BLEH351B 7 3 .20 2.53 2344 16.16 - 18.85 3.4 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 39.1
BLEH352A 7 4 .75 3.81 4917 19.19 - 25.13 4.5 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 48.2
BLEH352B 7 6 .50 4.97 4687 18.59 - 37.69 6.7 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 55.2
BLEH353A 7 7 .21 5.73 7375 20.61 - 37.69 6.7 3x350 450 1.98 1400 4p 54 1/2"SAE 28mm 69.3
BLEH353B 7 9 .78 7.65 7031 20.01 - 56.54 10.1 3x350 450 1.98 1400 4p 54 5/8"SAE 28mm 78.3
BLEH354A 7 9 .67 7.63 9834 21.62 - 50.25 9 4x350 600 2.64 1400 4p 55 5 /8 "S AE 3 5m m 1 00 .4
BLEH354B 7 13.07 10.07 9375 21.01 - 75.38 13.4 4x350 600 2.64 1400 4p 55 5 /8 "S AE 3 5m m 1 02 .4
BLEH401B 7 4.45 3.56 3328 19.7 39.4 25.78 4.6 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 43.7
BLEH401C 7 5.41 4.22 3191 19.07 38.14 34.37 6.1 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 47.7
BLEH402B 7 9.20 7.26 6693 22.55 45.1 52.92 9.4 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 87.4
BLEH402C 7 11.09 8.72 6428 21.94 43.88 70.56 12.6 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 96.4
BLEH403B 7 13.95 10.92 10060 24.2 48.4 80.05 14.3 3x400 480 2.19 1430 4p 56 22 42mm 125.1
BLEH403C 7 16.78 13.01 9664 23.6 47.2 106.7 19 3x400 480 2.19 1430 4p 56 22 42mm 135.1
BLEH502A 7 13.41 10.42 15690 37.82 75.64 62.94 11.2 2x500 1360 6 1300 4p 58 16 35mm 164
BLEH502B 7 18.37 14.41 15150 36.81 73.62 94.41 16.8 2x500 1360 6 1300 4p 58 22 35mm 178
BLEH502C 7 22.40 17.22 14610 35.84 71.68 125.9 22.4 2x500 1360 6 1300 4p 58 22 42mm 191
BLEH503B 7 27.73 21.10 22740 38.87 77.74 142.5 25.4 3x500 2040 9 1300 4p 60 22 42mm 233.5
BLEH503C 7 33.81 26.05 21950 37.9 75.8 190 33.9 3x500 2040 9 1300 4p 60 28 42mm 242.5
BLEH504B 7 37.09 28.33 30340 40.33 80.66 190.5 34 4x500 2720 12 1300 4p 61 28 54mm 301
BLEH504C 7 45.22 34.89 29290 39.36 7 8.72 254 45.3 4x500 2720 12 1300 4p 61 28 54mm 339
BLEH251A 10 1.20 0.97 1480 13.64 - 5.424 1.3 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 17
BLEH251B 10 1.59 1.31 1445 13.38 - 8.135 2 1x250 150 0.6 2500 2p 56 1/2"SAE 12mm 19
BLEH252A 10 2.40 1.96 2961 15.37 - 10.85 2.7 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 28
BLEH252B 10 3.31 2.71 2890 15.11 - 16.27 4 2x250 300 1.2 2500 2p 59 1/2"SAE 22mm 33
BLEH253A 10 3.76 2.96 4441 16.38 - 16.27 4 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 42
BLEH253B 10 5.18 4.11 4335 16.12 - 24.41 6 3x250 450 1.8 2500 2p 61 1/2"SAE 22mm 47
BLEH351A 10 1.95 1.60 2494 16.95 - 9.039 2.2 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 32.1
BLEH351B 10 2.81 2.24 2400 16.46 - 13.56 3.4 1x350 150 0.66 1400 4p 49 1/2"SAE 22mm 39.1
BLEH352A 10 4.07 3.29 4988 19.38 - 18.08 4.5 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 48.2
BLEH352B 10 5.74 4.45 4800 18.88 - 27.12 6.7 2x350 300 1.32 1400 4p 52 1/2"SAE 28mm 55.2
BLEH353A 10 6.19 4.95 7482 20.79 - 27.12 6.7 3x350 450 1.98 1400 4p 54 1/2"SAE 28mm 69.3
BLEH353B 10 8.60 6.79 7199 20.3 - 40.68 10.1 3x350 450 1.98 1400 4p 54 5/8"SAE 28mm 78.3
BLEH354A 10 8.32 6.62 9975 21.8 - 36.16 9 4x350 600 2.64 1400 4p 55 5/8"SAE 35mm 100.4
BLEH354B 10 11.53 8.99 9599 21.31 - 54.24 13.4 4x350 600 2.64 1400 4p 55 5/8"SAE 35mm 102.4
BLEH401B 10 3.88 3.13 3399 20.02 40.04 18.55 4.6 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 43.7
BLEH401C 1 0 4.83 3.79 3278 19.47 38.94 24.73 6.1 1x400 160 0.73 1430 4p 51 1/2"SAE 28mm 47.7
BLEH402B 10 8.05 6.40 6830 22.87 45.74 38.07 9.4 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 87.4
BLEH402C 10 9.89 7.82 6596 22.33 44.66 50.77 12.6 2x400 320 1.46 1430 4p 54 5/8"SAE 35mm 96.4
BLEH403B 10 12.24 9.67 10260 24.51 49.02 57.6 14.3 3x400 480 2.19 1430 4p 56 22 42mm 125.1
BLEH403C 10 15.02 11.75 9914 23.98 47.96 76.8 19 3x400 480 2.19 1430 4p 56 22 42mm 135.1
BLEH502A 10 11.59 9.12 15870 38.14 76.28 45.29 11.2 2x500 1360 6 1300 4p 58 16 35mm 164
BLEH502B 10 16.09 12.74 15410 37.3 74.6 67.93 16.8 2x500 1360 6 1300 4p 58 22 35mm 178
BLEH502C 10 20.02 15.55 14960 36.46 72.92 90.57 22.4 2x500 1360 6 1300 4p 58 22 42mm 191
BLEH503B 10 24.50 18.87 23130 39.35 78.7 102.5 25.4 3x500 2040 9 1300 4p 60 22 42mm 233.5
BLEH503C 10 30.20 23.51 22460 38.52 77.04 136.7 33.9 3x500 2040 9 1300 4p 60 28 42mm 242.5
BLEH504B 10 32.73 25.30 30860 40.8 81.6 137.1 34 4x500 2720 12 1300 4p 61 28 54mm 301
BLEH504C 10 40.39 31.47 29970 39.98 79.96 182.8 45.3 4x500 2720 12 1300 4p 61 28 54mm 339
*Nominal capacity according to ENV328 and Eurovent regulations (refrigerant R404A,ΔT=T INair -Tev).
SC2: TINair =0°C, Tev=-8°C.
SC3: TINair = -18°C, Tev=-25°C.
Use external equalized thermostatic expansion valve.
23The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 8/24
AlfaCubic Technical Data
Air Throwm
Conn. Sizemm
TotalPower
W
TotalCurrent
ARPM
Description
Finspac-ingmm
Capacity*SC2kW
Ca-pacity*SC3kW
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVolume
dm3
Fanmotors
400V/3Ph/50Hz
PoleNoisedB A)Lp A) Inlet Outlet
Weightkg
GLEH401B 4 6.51 5.09 3830 22 44 43.83 4.6 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 50.7
GLEH401C 4 7.43 5.59 3607 20.98 41.96 58.44 6.1 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 55.7
GLEH402B 4 13.25 10.13 7722 24.92 49.84 89.96 9.4 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 101.4
GLEH402C 4 15.31 11.66 7285 23.91 47.82 119.9 12.6 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 106.4
GLEH403B 4 19.96 15.09 11610 26.59 53.18 136.1 14.3 3x400 1260 2.16 1370 4p 58 22 42mm 137.1
GLEH403C 4 22.87 17.13 10960 25.59 51.18 181.5 19 3x400 1260 2.16 1370 4p 58 22 42mm 147.1
GLEH502A 4 18.26 13.00 15780 37.98 75.96 107 11.2 2x500 1440 2.82 1390 4p 58 16 35mm 135
GLEH502B 4 24.52 18.25 15050 36.63 73.26 160.5 16.8 2x500 1440 2.82 1390 4p 58 22 35mm 154
GLEH502C 4 28.59 21.37 14390 35.42 70.84 214 22.4 2x500 1440 2.82 1390 4p 58 22 42mm 172
GLEH503B 4 36.59 26.75 22600 38.7 77.4 242.2 25.4 3x500 2160 4.23 1390 4p 60 22 42mm 218.5
GLEH503C 4 43.20 32.39 21620 37.49 74.98 322.9 33.9 3x500 2160 4.23 1390 4p 60 28 42mm 235.5
GLEH504B 4 49.06 36.06 30160 40.16 80.32 323.9 34 4x500 2880 5.64 1390 4p 61 28 54mm 279
GLEH504C 4 57.81 43.41 28850 38.95 77.9 431.9 45.3 4x500 2880 5.64 1390 4p 61 28 54mm 327
RLEH401B 5.5 5.56 4.40 3955 22.58 45.16 32.34 4.6 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 45.7
RLEH401C 5.5 6.62 5.05 3750 21.64 43.28 43.12 6.1 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 50.7
RLEH402B 5.5 11.45 8.87 7968 25.48 50.96 66.39 9.4 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 93.4
RLEH402C 5.5 13.61 10.50 7567 24.56 49.12 88.52 12.6 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 101.4
RLEH403B 5.5 17.30 13.28 11980 27.15 54.3 100.4 14.3 3x400 1260 2.16 1370 4p 58 22 42mm 131.1
RLEH403C 5.5 20.48 15.54 11380 26.23 52.46 133.9 19 3x400 1260 2.16 1370 4p 58 22 42mm 142.1
RLEH502A 5.5 15.49 11.41 16040 38.46 76.92 78.97 11.2 2x500 1440 2.82 1390 4p 58 16 35mm 169
RLEH502B 5.5 21.14 16.09 15400 37.29 74.58 118.4 16.8 2x500 1440 2.82 1390 4p 58 22 35mm 186
RLEH502C 5.5 25.36 19.23 14820 36.21 72.42 157.9 22.4 2x500 1440 2.82 1390 4p 58 22 42mm 201
RLEH503B 5.5 31.72 23.76 23130 39.35 78.7 178.7 25.4 3x500 2160 4.23 1390 4p 60 22 42mm 245.5
RLEH503C 5.5 38.29 29.12 22260 38.28 76.56 238.3 33.9 3x500 2160 4.23 1390 4p 60 28 42mm 258.5
RLEH504B 5.5 42.47 31.96 30860 40.8 81.6 239 34 4x500 2880 5.64 1390 4p 61 28 54mm 316
RLEH504C 5.5 51.22 39.01 29700 39.73 79.46 318.7 45.3 4x500 2880 5.64 1390 4p 61 28 54mm 359
BLEH401B 7 4.87 3.88 4039 22.97 45.94 25.78 4.6 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 43.7
BLEH401C 7 5.95 4.59 3848 22.08 44.16 34.37 6.1 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 47.7
BLEH402B 7 10.09 7.89 8131 25.86 51.72 52.92 9.4 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 87.4
BLEH402C 7 12.23 9.52 7757 25 50 70.56 12.6 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 96.4
BLEH403B 7 15.29 11.86 12220 27.52 55.04 80.05 14.3 3x400 1260 2.16 1370 4p 58 22 42mm 125.1
BLEH403C 7 18.49 14.17 11670 26.67 53.34 106.7 19 3x400 1260 2.16 1370 4p 58 22 42mm 135.1
BLEH502A 7 13.58 10.54 16210 38.77 77.54 62.94 11.2 2x500 1440 2.82 1390 4p 58 16 35mm 164
BLEH502B 7 18.63 14.60 15630 37.71 75.42 94.41 16.8 2x500 1440 2.82 1390 4p 58 22 35mm 178
BLEH502C 7 22.76 17.47 15100 36.73 73.46 125.9 22.4 2x500 1440 2.82 1390 4p 58 22 42mm 191
BLEH503B 7 28.11 21.36 23470 39.77 79.54 142.5 25.4 3x500 2160 4.23 1390 4p 60 22 42mm 233.5
BLEH503C 7 34.36 26.43 22680 38.79 77.58 190 33.9 3x500 2160 4.23 1390 4p 60 28 42mm 242.5
BLEH504B 7 37.60 28.68 31310 41.22 82.44 190.5 34 4x500 2880 5.64 1390 4p 61 28 54mm 301
BLEH504C 7 45.95 35.40 30260 40.25 80.5 254 45.3 4x500 2880 5.64 1390 4p 61 28 54mm 339
BLEH401B 10 4.26 3.41 4141 23.44 46.88 18.55 4.6 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 43.7
BLEH401C 1 0 5.33 4.15 3968 22.64 45.28 24.73 6.1 1x400 420 0.72 1370 4p 53 1/2"SAE 28mm 47.7
BLEH402B 10 8.87 7.00 8330 26.32 52.64 38.07 9.4 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 87.4
BLEH402C 10 10.93 8.59 7993 25.54 51.08 50.77 12.6 2x400 840 1.44 1370 4p 56 5/8"SAE 35mm 96.4
BLEH403B 10 13.46 10.56 12520 27.97 55.94 57.6 14.3 3x400 1260 2.16 1370 4p 58 22 42mm 125.1
BLEH403C 10 16.60 12.85 12020 27.21 54.42 76.8 19 3x400 1260 2.16 1370 4p 58 22 42mm 135.1
BLEH502A 10 11.75 9.23 16400 39.13 78.26 45.29 11.2 2x500 1440 2.82 1390 4p 58 16 35mm 164
BLEH502B 1 0 16.33 12.92 15910 38.21 76.42 67.93 16.8 2x500 1440 2.82 1390 4p 58 22 35mm 178
BLEH502C 10 20.34 15.77 15440 37.35 74.7 90.57 22.4 2x500 1440 2.82 1390 4p 58 22 42mm 191
BLEH503B 10 24.85 19.11 23880 40.27 80.54 102.5 25.4 3x500 2160 4.23 1390 4p 60 22 42mm 233.5
BLEH503C 10 30.68 23.85 23180 39.41 78.82 136.7 33.9 3x500 2160 4.23 1390 4p 60 28 42mm 242.5
BLEH504B 1 0 33.20 25.63 31860 41.72 83.44 137.1 34 4x500 2880 5.64 1390 4p 61 28 54mm 301
BLEH504C 1 0 41.03 31.92 30930 40.87 81.74 182.8 45.3 4x500 2880 5.64 1390 4p 61 28 54mm 339
*Nominal capacity according to ENV328 and Eurovent regulations (refrigerant R404A,ΔT=T INair -Tev).
SC2: TINair =0°C, Tev=-8°C.
SC3: TINair = -18°C, Tev=-25°C.
Use external equalized thermostatic expansion valve.
24The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 9/24
AlfaCubic Technical Data
Air Throwm
TotalPower
W
TotalCurrent
ARPM
Conn. Sizemm
Description
Finspac-ingmm
Ca-pacitykW
FluidFlowm3/h
FluidPres-sureDropkPa
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVol-umedm3
Fanmotors
230V/1ph/50Hz
PoleNoisedB A)Lp A)
Inlet Outlet
Weightkg
GLWH251A2 4 1.295 0.3 3.514 1416 13.16 - 12.81 1.3 1x250 150 0.6 2500 2p 56 1/2" 1/2" 19
GLWH251B2 4 1.989 0.4 11.38 1331 12.54 - 19.22 2 1x250 150 0.6 2500 2p 56 1/2" 1/2" 21
GLWH252A2 4 2.592 0.6 19.71 2831 14.89 - 25.63 2.7 2x250 300 1.2 2500 2p 59 3/4" 3/4" 31
GLWH252B3 4 3.449 0.8 16.28 2745 14.58 - 38.44 4 2x250 300 1.2 2500 2p 59 3/4" 3/4" 36
GLWH253A3 4 3.468 0.7 14.8 4266 15.95 - 38.44 4 3x250 450 1.8 2500 2p 61 3/4" 3/4" 45
GLWH253B4 4 5.01 1.1 19.18 4009 15.32 - 57.67 6.1 3x250 450 1.8 2500 2p 61 3/4" 3/4" 51
GLWH351A2 4 2.452 0.5 18.24 2318 16.03 - 21.36 2.2 1x350 150 0.66 1400 4p 49 1" 1" 35.1
GLWH351B3 4 3.344 0.7 15.43 2128 15.03 - 32.04 3.4 1x350 150 0.66 1400 4p 49 1" 1" 43.1
GLWH352A3 4 6.231 1.3 50.37 4614 18.39 - 42.72 4.5 2x350 300 1.32 1400 4p 52 1" 1" 52.2
GLWH352B4 4 8.574 1.9 59.86 4228 17.38 - 64.07 6.7 2x350 300 1.32 1400 4p 52 1" 1" 59.2
GLWH353A4 4 10.28 2.2 75.95 6909 19.79 - 64.07 6.7 3x350 450 1.98 1400 4p 54 1" 1" 73.3
GLWH353B6 4 12.77 2.8 54.52 6344 18.8 - 96.11 10.1 3x350 450 1.98 1400 4p 54 1" 1" 82.3
GLWH354A5 4 14.24 3.1 93.13 9207 20.79 - 85.43 9 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 104.4
GLWH354B8 4 16.95 3.7 51.84 8459 19.81 - 128.1 13.5 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 108.4
GLWH401B3 4 5.606 1.2 50.39 3062 18.47 36.94 43.83 4.6 1x400 160 0.73 1430 4p 51 1" 1" 50.7
GLWH401C4 4 5.888 1.3 33.07 2879 17.63 35.26 58.44 6.1 1x400 160 0.73 1430 4p 51 1" 1" 55.7
GLWH402B5 4 13.3 2.9 95 6158 21.32 42.64 8 9.96 9.5 2x400 320 1.46 1430 4p 54 1" 1" 101.4
GLWH402C6 4 15.93 3.4 105.5 5782 20.46 40.92 119.9 12.6 2x400 320 1.46 1430 4p 54 1" 1" 106.4
GLWH403B9 4 17.35 3.8 42.12 9285 23.02 46.04 136.1 14.3 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 137.1
GLWH403C9 4 24.01 5.2 99.77 8702 22.13 44.26 181.5 19.1 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 147.1
GLWH502A7 4 19.06 4.1 78.84 14980 36.5 73 107 11.3 2x500 1360 6 1300 4p 58 1" 1" 167
GLWH502B8 4 28.55 6.2 167.3 14050 34.8 69.6 160.5 16.9 2x500 1360 6 1300 4p 58 1" 1" 177
GLWH502C10 4 34.02 7.3 163.8 13230 33.29 66.58 214 22.5 2x500 1360 6 1300 4p 58 1" 1" 187
GLWH503B13 4 41.64 9 121.9 21130 36.89 73.78 242.2 25.5 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 240.5
GLWH503C16 4 50.02 10.8 126.2 19900 35.39 70.78 322.9 34 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 250.5
GLWH504B18 4 54.53 11.8 103.3 28200 38.36 76.72 323.9 34.1 4x500 2720 12 1300 4p 61 1"1/2 1"1/2 284
GLWH504C21 4 67.18 14.5 130.3 26560 36.85 73.7 431.9 45.4 4x500 2720 12 1300 4p 61 2" 2" 294
RLWH251A2 5.5 1.144 0.2 3.063 1439 13.34 - 9.457 1.3 1x250 150 0.6 2500 2p 56 1/2" 1/2" 18
RLWH251B2 5.5 1.764 0.4 9.203 1370 12.83 - 14.19 2 1x250 150 0.6 2500 2p 56 1/2" 1/2" 20
RLWH252A2 5.5 2.219 0.5 15.53 2912 15.19 - 18.91 2.7 2x250 300 1.2 2500 2p 59 3/4" 3/4" 30
RLWH252B3 5.5 3.22 0.7 14.06 2745 14.58 - 28.37 4 2x250 300 1.2 2500 2p 59 3/4" 3/4" 35
RLWH253A3 5.5 3.101 0.7 12.17 4334 16.12 - 28.37 4 3x250 450 1.8 2500 2p 61 3/4" 3/4" 44
RLWH253B3 5.5 7.18 1.6 80.64 4092 15.53 - 42.56 6.1 3x250 450 1.8 2500 2p 61 3/4" 3/4" 49
RLWH351A2 5.5 2.144 0.5 14.43 2380 16.35 - 15.76 2.2 1x350 150 0.66 1400 4p 49 1" 1" 34.1
RLWH351B3 5.5 2.975 0.6 12.6 2216 15.49 - 23.64 3.4 1x350 150 0.66 1400 4p 49 1" 1" 41.1
RLWH352A3 5.5 3.911 0.8 22.16 4768 18.8 - 31.52 4.5 2x350 300 1.32 1400 4p 52 1" 1" 50.2
RLWH352B4 5.5 5.292 1.2 26.51 4597 18.35 - 47.28 6.7 2x350 300 1.32 1400 4p 52 1" 1" 57.2
RLWH353A4 5.5 7.906 1.7 47.91 7115 20.15 - 47.28 6.7 3x350 450 1.98 1400 4p 54 1" 1" 71.3
RLWH353B5 5.5 11.75 2.5 78.11 6609 19.27 - 70.93 10.1 3x350 450 1.98 1400 4p 54 1" 1" 80.3
RLWH354A5 5.5 11.13 2.4 60.4 9479 21.15 - 63.05 9 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 102.4
RLWH354B8 5.5 9.527 2.1 18.79 8917 20.41 - 94.57 13.5 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 106.4
RLWH401B3 5.5 4.288 0.9 31.41 3174 18.99 37.98 32.34 4.6 1x400 160 0.73 1430 4p 51 1" 1" 45.7
RLWH401C3 5.5 6.577 1.4 89.23 2986 18.13 36.26 43.12 6.1 1x400 160 0.73 1430 4p 51 1" 1" 50.7
RLWH402B5 5.5 10.75 2.3 65.35 6370 21.81 43.62 66.39 9.5 2x400 320 1.46 1430 4p 54 1" 1" 93.4
RLWH402C6 5.5 13.4 2.9 77.69 6027 21.02 42.04 88.52 12.6 2x400 320 1.46 1430 4p 54 1" 1" 101.4
RLWH403B7 5.5 16.94 3.7 80.96 9572 23.46 46.92 100.4 14.3 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 131.1
RLWH403C9 5.5 20.2 4.4 73.53 9067 22.68 45.36 133.9 19.1 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 142.1
RLWH502A6 5.5 16.33 3.5 92.29 15270 37.05 74.1 78.97 11.3 2x500 1360 6 1300 4p 58 1" 1" 157
RLWH502B8 5.5 23.22 5 116 14500 35.62 71.24 118.4 16.9 2x500 1360 6 1300 4p 58 1" 1" 167
RLWH502C10 5.5 28.56 6.2 120.7 13770 3 4.29 68.58 157.9 22.5 2x500 1360 6 1300 4p 58 1" 1" 177
RLWH503B13 5.5 33.65 7.3 83.58 21790 37.7 75.4 178.7 25.5 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 230.5
RLWH503C16 5.5 41.85 9.1 92.52 20710 36.37 72.74 238.3 34 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 240.5
RLWH504B18 5.5 43.99 9.5 71.04 29090 39.17 78.34 239 34.1 4x500 2720 12 1300 4p 61 1"1/2 1"1/2 274
RLWH504C21 5.5 56.26 12.2 95.64 27630 37.83 75.66 318.7 45.4 4x500 2720 12 1300 4p 61 2" 2" 284
*Nominal capacity according to TINair = +2°C / R.H. = 85%, 30% Et. Gly. , Temp = -8 / -4°C. Use external equalized thermostatic expansion valve.
25The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 10/24
AlfaCubic Technical Data
Air Throwm
TotalPower
W
TotalCurrent
ARPM
Conn. Sizemm
Description
Finspac-ingmm
Ca-pacitykW
FluidFlowm3/h
FluidPres-sureDropkPa
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVol-umedm3
Fanmotors
230V/1ph/50Hz
PoleNoisedB A)Lp A)
Inlet Outlet
Weightkg
BLWH251A2 7 1.033 0.2 2.765 1454 13.44 - 7.538 1.3 1x250 150 0.6 2500 2p 56 1/2" 1/2" 17
BLWH251B1 7 2.047 0.4 82.14 1390 12.97 - 11.31 2 1x250 150 0.6 2500 2p 56 1/2" 1/2" 19
BLWH252A2 7 2.066 0.4 13.15 2907 15.17 - 15.08 2.7 2x250 300 1.2 2500 2p 59 3/4" 3/4" 28
BLWH252B2 7 4.029 0.9 64.5 2780 14.71 - 22.61 4 2x250 300 1.2 2500 2p 59 3/4" 3/4" 33
BLWH253A2 7 4.471 1 71.41 4346 16.15 - 22.61 4 3x250 450 1.8 2500 2p 61 3/4" 3/4" 42
BLWH253B3 7 6.008 1.3 58.89 4171 15.72 - 33.92 6.1 3x250 450 1.8 2500 2p 61 3/4" 3/4" 47
BLWH351A2 7 1.92 0.4 11.86 2418 16.55 - 12.56 2.2 1x350 150 0.66 1400 4p 49 1" 1" 32.1
BLWH351B3 7 2.693 0.6 10.57 2274 15.79 - 18.85 3.4 1x350 150 0.66 1400 4p 49 1" 1" 39.1
BLWH352A3 7 3.363 0.7 17.45 4921 19.2 - 25.13 4.5 2x350 300 1.32 1400 4p 52 1" 1" 48.2
BLWH352B3 7 7.051 1.5 94.12 4523 18.16 - 37.69 6.7 2x350 300 1.32 1400 4p 52 1" 1" 55.2
BLWH353A4 7 4.956 1.1 20.98 7270 20.42 - 37.69 6.7 3x350 450 1.98 1400 4p 54 1" 1" 69.3
BLWH353B5 7 9.875 2.1 57.48 6793 19.59 - 56.54 10.1 3x350 450 1.98 1400 4p 54 1" 1" 78.3
BLWH354A5 7 8.911 1.9 40.78 9650 21.37 - 50.25 9 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 100.4
BLWH354B6 7 14.01 3 82.19 9048 20.58 - 75.38 13.5 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 102.4
BLWH401B3 7 3.864 0.8 26.13 3242 19.3 38.6 25.78 4.6 1x400 160 0.73 1430 4p 51 1" 1" 43.7
BLWH401C3 7 5.61 1.2 67.45 3071 18.52 37.04 34.37 6.1 1x400 160 0.73 1430 4p 51 1" 1" 47.7
BLWH402B5 7 8.858 1.9 46.55 6512 22.14 44.28 52.92 9.5 2x400 320 1.46 1430 4p 54 1" 1" 87.4
BLWH402C6 7 11.48 2.5 59.42 6193 21.4 42.8 70.56 12.6 2x400 320 1.46 1430 4p 54 1" 1" 96.4
BLWH403B7 7 14.21 3.1 59.42 9780 23.78 47.56 80.05 14.3 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 125.1
BLWH403C9 7 17.31 3.7 56.27 9313 23.06 46.12 106.7 19.1 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 135.1
BLWH502A6 7 13.39 2.9 65 15470 37.41 74.82 6 2.94 11.3 2x500 1360 6 1300 4p 58 1" 1" 145
BLWH502B8 7 19.61 4.2 86.36 14780 36.15 72.3 94.41 16.9 2x500 1360 6 1300 4p 58 1" 1" 155
BLWH502C10 7 24.55 5.3 92.27 14130 34.94 69.88 125.9 22.5 2x500 1360 6 1300 4p 58 1" 1" 165
BLWH503B13 7 28.12 6.1 60.85 22220 38.23 76.46 142.5 25.5 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 218.5
BLWH503C16 7 35.78 7.7 70.05 21240 37.02 74.04 190 34 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 228.5
BLWH504B18 7 36.51 7.9 51.13 29660 39.69 79.38 190.5 34.1 4x500 2720 12 1300 4p 61 1"1/2 1"1/2 262
BLWH504C21 7 48.18 10.4 72.62 28340 38.48 76.96 254 45.4 4x500 2720 12 1300 4p 61 2" 2" 272
BLWH251A2 10 0.9427 0.2 2.522 1468 13.55 - 5.424 1.3 1x250 150 0.6 2500 2p 56 1/2" 1/2" 17
BLWH251B1 10 1.708 0.4 59.62 1418 13.18 - 8.135 2 1x250 150 0.6 2500 2p 56 1/2" 1/2" 19
BLWH252A2 10 1.887 0.4 11.23 2936 15.28 - 10.85 2.7 2x250 300 1.2 2500 2p 59 3/4" 3/4" 28
BLWH252B2 10 2.643 0.6 31.4 2892 15.12 - 16.27 4 2x250 300 1.2 2500 2p 59 3/4" 3/4" 33
BLWH253A2 10 3.732 0.8 51.98 4396 16.27 - 16.27 4 3x250 450 1.8 2500 2p 61 3/4" 3/4" 42
BLWH253B3 10 3.738 0.8 26.43 4338 16.13 - 24.41 6.1 3x250 450 1.8 2500 2p 61 3/4" 3/4" 47
BLWH351A2 10 1.743 0.4 10.04 2458 16.76 - 9.039 2.2 1x350 150 0.66 1400 4p 49 1" 1" 32.1
BLWH351B3 10 2.464 0.5 9.028 2338 16.13 - 13.56 3.4 1x350 150 0.66 1400 4p 49 1" 1" 39.1
BLWH352A3 10 3.221 0.7 15.74 4920 19.2 - 18.08 4.5 2x350 300 1.32 1400 4p 52 1" 1" 48.2
BLWH352B3 10 6.101 1.3 73.14 4660 18.51 - 27.12 6.7 2x350 300 1.32 1400 4p 52 1" 1" 55.2
BLWH353A4 10 4.29 0.9 16.87 7486 20.8 - 27.12 6.7 3x350 450 1.98 1400 4p 54 1" 1" 69.3
BLWH353B5 10 6.23 1.4 26.52 7207 20.31 - 40.68 10.1 3x350 450 1.98 1400 4p 54 1" 1" 78.3
BLWH354A5 10 5.766 1.2 18.88 9854 21.64 - 3 6.16 9 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 100.4
BLWH354B6 10 12.11 2.6 63.79 9320 20.94 - 54.24 13.5 4x350 600 2.64 1400 4p 55 1"1/4 1"1/4 102.4
BLWH401B3 10 3.522 0.8 22.14 3320 19.66 3 9.32 18.55 4.6 1x400 160 0.73 1430 4p 51 1" 1" 43.7
BLWH401C3 10 4.663 1 48.67 3173 18.98 3 7.96 24.73 6.1 1x400 160 0.73 1430 4p 51 1" 1" 47.7
BLWH402B5 10 6.004 1.3 23.94 6836 22.88 4 5.76 38.07 9.5 2x400 320 1.46 1430 4p 54 1" 1" 87.4
BLWH402C6 10 7.61 1.7 29.26 6604 22.35 44.7 50.77 12.6 2x400 320 1.46 1430 4p 54 1" 1" 96.4
BLWH403B7 10 9.248 2 27.89 10050 24.2 48.4 57.6 14.3 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 125.1
BLWH403C9 10 11.89 2.6 28.77 9925 24 48 76.8 19.1 3x400 480 2.19 1430 4p 56 1"1/4 1"1/4 135.1
BLWH502A6 10 11.19 2.4 47.38 15680 37.79 75.58 45.29 11.3 2x500 1360 6 1300 4p 58 1" 1" 145
BLWH502B8 10 16.88 3.6 66.2 15100 36.72 73.44 67.93 16.9 2x500 1360 6 1300 4p 58 1" 1" 155
BLWH502C10 10 21.53 4.7 73.37 14530 35.68 71.36 90.57 22.5 2x500 1360 6 1300 4p 58 1" 1" 165
BLWH503B13 10 23.83 5.2 45.51 22690 38.8 77.6 102.5 25.5 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 218.5
BLWH503C16 10 31.06 6.7 54.57 21840 37.76 75.52 136.7 34 3x500 2040 9 1300 4p 60 1"1/4 1"1/4 228.5
BLWH504B18 10 19.99 4.3 17.64 30570 40.54 81.08 137.1 34.1 4x500 2720 12 1300 4p 61 1"1/2 1"1/2 262
BLWH504C21 10 41.93 9.1 56.8 29140 39.22 78.44 182.8 45.4 4x500 2720 12 1300 4p 61 2" 2" 272
*Nominal capacity according to TINair = +2°C / R.H. = 85%, 30% Et. Gly. , Temp = -8 / -4°C. Use external equalized thermostatic expansion valve.
26The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 11/24
AlfaCubic Technical Data
Air Throwm
TotalPower
W
TotalCurrent
ARPM
Conn. Sizemm
Description
Finspac-ingmm
Ca-pacitykW
FluidFlowm3/h
FluidPres-sureDropkPa
Air Flowm3/h
- Alfa Str-eamer
Surfacem2
TubeVol-umedm3
Fanmotors
400V/3ph/50Hz
PoleNoisedB A)Lp A)
Inlet Outlet
Weightkg
GLWH401B3 4 6.412 1.4 63.8 3673 21.28 42.56 43.83 4.6 1x400 420 0.72 1370 4p 53 1" 1" 50.7
GLWH401C4 4 7.048 1.5 45.49 3425 20.14 40.28 58.44 6.1 1x400 420 0.72 1370 4p 53 1" 1" 55.7
GLWH402B5 4 14.8 3.2 114.7 7396 24.17 4 8.34 89.96 9.5 2x400 840 1.44 1370 4p 56 1" 1" 101.4
GLWH402C6 4 17.84 3.9 128.7 6895 23.02 46.04 119.9 12.6 2x400 840 1.44 1370 4p 56 1" 1" 106.4
GLWH403B9 4 19.81 4.3 53.22 11150 25.88 51.76 136.1 14.3 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 137.1
GLWH403C9 4 26.9 5.8 121.8 10380 24.7 49.4 181.5 19.1 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 147.1
GLWH502A7 4 19.37 4.2 81.09 15460 37.4 74.8 107 11.3 2x500 1440 2.82 1390 4p 58 1" 1" 167
GLWH502B8 4 29.09 6.3 173 14550 35.73 71.46 160.5 16.9 2x500 1440 2.82 1390 4p 58 1" 1" 177
G LWH50 2C 10 4 34. 84 7.5 170.8 13770 34.29 68.58 214 22.5 2x500 1440 2.82 1390 4p 58 1" 1" 187
GLWH503B13 4 42.44 9.2 126 21880 37.81 75.62 242.2 25.5 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 240.5
GLWH503C16 4 51.23 11.1 131.7 20710 36.38 72.76 322.9 34 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 250.5
GLWH504B18 4 55.58 12 106.9 29200 39.28 78.56 323.9 34.1 4x500 2880 5.64 1390 4p 61 1"1/2 1"1/2 284
GLWH504C21 4 68.81 14.9 135.9 27640 37.84 75.68 431.9 45.4 4x500 2880 5.64 1390 4p 61 2" 2" 294
RLWH401B3 5.5 4.567 1 35.09 3832 22.01 44.02 32.34 4.6 1x400 420 0.72 1370 4p 53 1" 1" 45.7
RLWH401C3 5.5 7.349 1.6 108.4 3573 20.82 41.64 43.12 6.1 1x400 420 0.72 1370 4p 53 1" 1" 50.7
RLWH402B5 5.5 12.01 2.6 79.67 7684 24.83 49.66 66.39 9.5 2x400 840 1.44 1370 4p 56 1" 1" 93.4
RLWH402C6 5.5 15.01 3.3 95.29 7218 23.76 47.52 88.52 12.6 2x400 840 1.44 1370 4p 56 1" 1" 101.4
RLWH403B7 5.5 18.78 4.1 97.09 11550 26.49 52.98 100.4 14.3 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 131.1
RLWH403C9 5.5 22.64 4.9 90.22 10860 25.44 50.88 133.9 19.1 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 142.1
RLWH502A6 5.5 16.57 3.6 94.72 15770 37.95 75.9 78.97 11.3 2x500 1440 2.82 1390 4p 58 1" 1" 157
RLWH502B8 5.5 23.62 5.1 119.5 14990 36.52 73.04 118.4 16.9 2x500 1440 2.82 1390 4p 58 1" 1" 167
RLWH502C10 5.5 29.15 6.3 125.1 14280 35.23 70.46 157.9 22.5 2x500 1440 2.82 1390 4p 58 1" 1" 177
RLWH503B13 5.5 34.24 7.4 86.18 22520 38.6 77.2 178.7 25.5 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 230.5
RLWH503C16 5.5 42.73 9.3 95.97 21470 37.31 74.62 238.3 34 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 240.5
RLWH504B18 5.5 44.78 9.7 73.29 30060 40.07 80.14 239 34.1 4x500 2880 5.64 1390 4p 61 1"1/2 1"1/2 274
RLWH504C21 5.5 57.44 12.4 99.19 28650 38.77 77.54 318.7 45.4 4x500 2880 5.64 1390 4p 61 2" 2" 284
BLWH401B3 7 4.111 0.9 29.1 3925 22.44 44.88 25.78 4.6 1x400 420 0.72 1370 4p 53 1" 1" 43.7
BLWH401C3 7 6.309 1.4 83.1 3686 21.34 42.68 34.37 6.1 1x400 420 0.72 1370 4p 53 1" 1" 47.7
BLWH402B5 7 10.01 2.2 57.76 7880 25.28 50.56 52.92 9.5 2x400 840 1.44 1370 4p 56 1" 1" 87.4
BLWH402C6 7 12.87 2.8 72.53 7441 24.27 48.54 70.56 12.6 2x400 840 1.44 1370 4p 56 1" 1" 96.4
BLWH403B7 7 15.86 3.4 72.29 11840 26.93 53.86 80.05 14.3 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 125.1
BLWH403C9 7 19.41 4.2 68.7 11190 25.94 51.88 106.7 19.1 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 135.1
BLWH502A6 7 13.61 2.9 66.81 15970 38.33 76.66 62.94 11.3 2x500 1440 2.82 1390 4p 58 1" 1" 145
BLWH502B8 7 19.94 4.3 88.89 15270 37.04 74.08 94.41 16.9 2x500 1440 2.82 1390 4p 58 1" 1" 155
BLWH502C10 7 25.03 5.4 95.42 14620 35.85 71.7 125.9 22.5 2x500 1440 2.82 1390 4p 58 1" 1" 165
BLWH503B13 7 28.61 6.2 62.74 22940 39.12 78.24 142.5 25.5 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 218.5
BLWH503C16 7 36.49 7.9 72.51 21980 37.94 75.88 190 34 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 228.5
BLWH504B18 7 37.18 8 52.79 30620 40.58 81.16 190.5 34.1 4x500 2880 5.64 1390 4p 61 1"1/2 1"1/2 262
BLWH504C21 7 49.13 10.6 75.15 29330 3 9.39 78.78 254 45.4 4x500 2880 5.64 1390 4p 61 2" 2" 272
BLWH401B3 10 3.764 0.8 24.95 4033 22.94 4 5.88 18.55 4.6 1x400 420 0.72 1370 4p 53 1" 1" 43.7
BLWH401C3 10 5.477 1.2 64.77 3821 21.96 43.92 24.73 6.1 1x400 420 0.72 1370 4p 53 1" 1" 47.7
BLWH402B5 10 6.502 1.4 27.93 8339 26.34 5 2.68 38.07 9.5 2x400 840 1.44 1370 4p 56 1" 1" 87.4
BLWH402C6 10 11.19 2.4 56.64 7705 24.88 49.76 50.77 12.6 2x400 840 1.44 1370 4p 56 1" 1" 96.4
BLWH403B7 10 13.6 2.9 55.08 12170 27.44 54.88 57.6 14.3 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 125.1
BLWH403C9 10 16.88 3.6 53.67 11590 26.55 53.1 76.8 19.1 3x400 1260 2.16 1370 4p 58 1"1/4 1"1/4 135.1
BLWH502A6 10 11.4 2.5 48.94 16190 38.74 77.48 45.29 11.3 2x500 1440 2.82 1390 4p 58 1" 1" 145
BLWH502B8 10 17.17 3.7 68.25 15580 37.62 75.24 67.93 16.9 2x500 1440 2.82 1390 4p 58 1" 1" 155
BLWH502C10 10 21.94 4.7 75.84 15020 36.58 73.16 90.57 22.5 2x500 1440 2.82 1390 4p 58 1" 1" 165
BLWH503B13 10 24.31 5.3 47.1 23420 39.7 79.4 102.5 25.5 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 218.5
BLWH503C16 10 31.69 6.8 56.52 22570 38.66 77.32 136.7 34 3x500 2160 4.23 1390 4p 60 1"1/4 1"1/4 228.5
BLWH504B18 10 20.15 4.4 17.89 31560 41.44 82.88 137.1 34.1 4x500 2880 5.64 1390 4p 61 1"1/2 1"1/2 262
BLWH504C21 10 42.88 9.3 59.31 30110 40.11 80.22 182.8 45.4 4x500 2880 5.64 1390 4p 61 2" 2" 272
*Nominal capacity according to TINair = +2°C / R.H. = 85%, 30% Et. Gly. , Temp = -8 / -4°C. Use external equalized thermostatic expansion valve.
27The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no responsibility
for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 12/24
AlfaCubic Drawings
.
ky AlfaCubicky Drawings
.
DIMENSIONS mm)
DX Brine/NH3/HP ALL ALL ALL ALL ALLODEL
A A B C D E F
GL/RL/BL 251 840 960 530 450 395 410 250
GL/RL/BL 252 1340 1460 1030 450 395 410 250
GL/RL/BL 253 1840 1960 1530 450 395 410 250
GL/RL/BL 351 840 960 530 495 585 410 300
GL/RL/BL 352 1340 1460 1030 495 585 410 300
GL/RL/BL 353 1840 1960 1530 495 585 410 300
GL/RL/BL 354 2340 2470 2030 495 585 410 300
GL/RL/BL 401 910 1030 600 615 685 530 450
GL/RL/BL 402 1510 1640 1200 615 685 530 450
GL/RL/BL 403 2110 2230 1800 615 685 530 450
GL/RL/BL 502 2140 2140 1700 650 830 580 450
GL/RL/BL 503 2990 2990 2550 650 830 580 450
GL/RL/BL 504 3840 3840 3400 650 830 580 450
We reserve the right to change our technical data without prior notice.
B
A
B
A
B
A
B
A
D
C
E
30
50 1 0
F
28The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 13/24
AlfaCubic Options
.
ky AlfaCubicky Options
Fan motors
6-pole, 230V/1Ph
4-pole, 400V/3Ph
6-pole, 400 V/3ph
Model:ALLAPPLICATIONS
For diameter:
350mm
400mm
500mm
Fan pre-wired to main terminal box
Fan motor pre-wired to main terminal junction box IP55, in painted galvanized steel.
See Electrical Data page.
Model:
ALLAPPLICATIONS
All Models
Local safety switch wired
Local safety switch and cabling for each electric fan motor.
Plastic covering box, IP66, nominal current 16A – 3 phases, insulated voltage 600V.
Reference and standard CE/UL/CSA. Per unit.
Model:ALLAPPLICATIONS
All Models
Fan ring heater FRH)
Application:
To prevent the freezing up of the fan blades at the collar in extremely humid conditions during
defrost in cooling or freezing rooms.
Supply conditions:
Electric heater with stainless steel shell, stainless steel fixing spring and connection box.
Model:ALL
APPLICATIONS
All Models
Air sock adapter ring
Ø
Applications: Flower, fruit and vegetable storage areas, supermarkets, ba keries, slaughter houses
and other meat-processing operations. Price per unit cooler.
Benefits: Equal cooling effect without draught, even temperature distribution, com fort in cold working
areas.
The sock reduces the airflow and capacity. Please contact Alfa Laval for design and unit section.
Model:
Ø 400/500mm
29The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 14/24
AlfaCubic Options
AlfaStreamer
Increase of the axial airflow speed by deviation of centrifugal and circular flow components.
Increased air throw for refrigeration applications.
Applications: cold store s, wo rking r ooms
Model:ALLAPPLICATIONSØ 400mmNo. of fans
2, 3, 4 ,5Ø 500 mmNo. of fans
2, 3, 4
Cabinet made entirely of stainless steel
Casework component in stainless steel AISI 304.
Application Use: More information on corrosion prevention can be found in the Miscellaneous section.
Model:ALLAPPLICATIONS
All Models
Insulated drip tray
Construction: Sandwich manufactured with two aluminium shells and 12mm of polyethylene
insulation in between.
Features: The insulation prevents water condensing on the bottom side of the drip-tray and reduces
the transfer of the defrost heat into the cold room. It can be combined with Electrical or Hot Gas
defrost.
Applications: Room tem peratures below -25°C and foo d processing rooms.
Model:ALLAPPLICATIONS
All Models
Cable electric heater
Applications:
We recommend that you heat the drain pipeline while defrosting to prevent ice forming in the pipes.
The flexible electric heater can easily be placed inside the pipe.
Power: 70W.
Voltage: 230V
Model:ALLAPPLICATIONS
All Models
Reheating coil
Use:
It’s an additional coil used for dehumidifying or heating the air outlet of the evaporator. It can be
one or two rows deep. There are two systems:
- using warm water with a minimal flow rate providing small air temperature rise.
- Using electric heaters fixed into the finned tube coil.
Quick selection:
• Product available: AlfaCubic Dx, Ammonia.
• Permanent 2 row tube for reheating coil.
• Coil sizes with reheating water:
• A (cooling size) + 2 rows (reheating coil)
• B (cooling size) + 2 rows (reheating coil)
• In case C coil size: due to space limitations in the unit, the cooling coil will be B with + 2
rows for reheating
-
Model:DX/Ammonia
All Models, exceptØ 500
Coil Treatment / Material
Pre-coated fins: Epoxy-coated, pre-painted aluminium fins.
Cataphoresis treatment: An electrolytic process is achieved by submerging the coil in a paint bath,
where it acts as a cathode and gets completely coated in an epoxy paint, which gives exceptional
protection against corrosion. Recommended for alkaline or salty atmospheres.
Stainless steel tubes with aluminium fins: The coil is available in stainless steel tubes with aluminium
fins.
Application Use: More information on corrosion prevention can be found in the Miscellaneous section.
Model:ALLAPPLICATIONS
All Models
30The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 15/24
AlfaCubic Options
Carbon Steel Connection
Additional end terminal connection for stainless steel headers. Model:ALLAPPLICATIONS
NH3
31The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 16/24
AlfaCubic Electrical data
.
ky AlfaCubicky Electrical data
AlfaCubic junction box for motors
Series 250 / 350
Function
Junction box complete with screw-on cover, cable glands and terminal strip.
General data
Material: Plastic
IP Protection Class: Min IP55
Colour: Grey RAL7035
Insulation class: II
Ambient Temp.: -25°C Max +50°C
Weight: 0,5 kg
Dimensions Electric wiring diagram
N
F
P EP
I N C O M
N
MI N
GN
S
2
V -V
5
6
H
M
F
MOTOR
1
M
F
MOTOR2
M
F
MOTOR
3
M
F
MOTOR
4
32The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 17/24
AlfaCubic Electrical data
.
AlfaCubic junction box for motors
Series 400 / 500
Function
Metallic junction box complete with cable glands and terminal strip.
General data
Material: Sheet of steel
IP Protection Class: Min IP55
Colour: Grey RAL7032
Insulation class: I
Ambient Temp.: -25°C Max +50°C
Weight: approx. 4Kg
Dimensions Electric wiring diagram
IN
MIN
S
P P P
3
4
V -V
5 0 5
H
F
M OMOTOR S R
C
NNN
ON
33The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 18/24
AlfaCubic Electrical data
.
AlfaCubic junction box for E defrost
Series 250 / 350
Function
Junction box complete with screw-on cover, cable glands and terminal strip.
General data
Material: Plastic
IP Protection Class: Min IP55
Colour: Grey RAL7035
Insulation class: II
Ambient Temp.: -25°C Max +50°C
Weight: 0,5 kg
Dimensions Electric wiring diagram
N
F
P EP
IN
M I N
MIN
S U P
S
2
V -V
5
H
B
C
OM
E RE
C O N N
C
N
ON
OP
T ITON
N
L
P EP
I N C O M
N
MI N
GN
S
P PP
4
V -V
5
H
L
L
B YB
C U S
C
OME
C O N N E C
C
N
T ITON
S
N DN
R OP
T .T
N
L
P EP
I N C O M
N
MI N
GN
S
4
5
H
L
L
B
C U S T
C
OM
E RE
R OP
T .T
GL2
B /B2
2
B /B3
3
A /A3
5 3 A / 3 5 4
5
3
R
2
B /B2
2
B /B3
3
A /A3
/ 3 5 4
/3
B
2
2
2
3
3
3 5 35
3 5 4
3
R
3
3
3
3 5 45
B
3 5 15
/ 3/3
3 53
B / 3 5 4
B3
C O
N N
C
N
T ITON
S T A
S
N DN
G
L3
3
3
3 5 45
N
L
P
I N C O M
N
MI N
GN
S
P PP
4
5
H
L
L
B
C UC
OM
E
C O N N E C
C
N
T ITON
S TS
N DN
R
OP
T .T
GL2
A /A2
2 5 3
2
R
2
2
2
B
2
2
2 5 3
2
34The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 19/24
AlfaCubic Electrical data
..
AlfaCubic junction box for E defrost
Series 400 / 500
Function
Metallic junction box complete with cable glands and terminal strip.
General data
Material: Sheet of steel
IP Protection Class: Min IP55
Colour: Grey RAL7032
Insulation class: I
Ambient Temp.: -25°C Max +50°C
Weight: approx. 4Kg
Dimensions Electric wiring diagram
N
L
I N C O M
N
MI N
GN
S
P PP
4
V -V
5
H
L
L
B
C
OM
E
P EP
N
L
L
L
P EP
ROP
T .T
L L L N
N
L
IN
M I N
MIN
S U P
S
4
V -V
5
H
L
L
B
C
OM
E RE
P EP
L
NL
L
7891
C O N N E C
C
N
ON
S T A
S
N DN
35The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 20/24
AlfaCubic Electrical data
AlfaCubic for fan ring heater connection
All Series
Function
Junction box complete with screw-on cover, cable glands and terminal strip.
General data
Material: Plastic
IP Protection Class: Min IP55
Colour: Grey RAL7035
Insulation class: II
Ambient Temp.: -25°C Max +50°C
Weight: 0,5 kg
Dimensions Electric wiring diagram
36The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 21/24
AlfaCubic Electric Heater
.
ky AlfaCubicky Electric Heater
ALL SERIES
Function
The elements are designed to operate in a refrigeration field with high moisture rate.
Special care is taken in selecting the power supply, cables and insulation materials. Less stream (easy mounting)
General data
E HG+E Electric element
Coil Drip-tray Drip-tray Drain lineodel
n° Watt n° Watt n° Watt P W)
_251A 2 780 1 270 1 270 70 _251B 3 1170 1 270 1 270 70
_252A 2 1560 1 540 1 540 70
_252B 3 2340 1 540 1 540 70
_253A 2 2360 1 800 1 800 70
_253B 3 3540 1 800 1 800 70
_351A 3 1170 1 270 1 270 70
_351B 4 1560 1 270 1 270 70
_352A 3 2340 1 540 1 540 70
_352B 4 3120 1 540 1 540 70
_353A 3 3540 1 800 1 800 70
_353B 4 4720 1 800 1 800 70
_354A 3 4710 1 1000 1 1000 70
_354B 4 6280 1 1000 1 1000 70
_401B 7 3150 1 450 1 450 100
_401C 9 4050 1 450 1 450 100
_402B 7 6300 1 900 1 900 100
_402C 9 8100 1 900 1 900 100
_403B 7 8750 1 1250 1 1250 100
_403C 9 11250 1 1250 1 1250 100
_502A 4 6400 1 1600 1 1600 100
_502B 6 9600 1 1600 1 1600 100
_502C 8 12800 1 1600 1 1600 100
_503B 6 16800 1 2800 1 2800 100
_503C 8 22400 1 2800 1 2800 100
_504B 7 18200 1 2600 1 2600 100
_504C 10 26000 1 2600 1 2600 100
We reserve the right to change our technical data without prior notice.
37The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 22/24
AlfaCubic Code description
.
ky AlfaCubicky Code description
ALFACUBICRL W H 25 1 A S 230V 2 CR _A - AL 7 CU ...
GL Green LineRL Red LineBL Blue Line
1) ApplicationE Direct Expansion Evaporator W Brine Unit Cooler A Ammonia Pump Evaporator H CO2 High Pressure Pump
2) Noise levelH 4-pole fan motor L 6-pole fan motor
3) Fan diameter Ø25 250 mm35 350 mm40 400 mm50 500 mm
4) Number of Fans1 , 2 , 3, 4
5) Coil Size A, B, C
6) Fan motors phaseS Single phase
D/Y Three-phase
7) Fan power 400V; 230V)
8) Circuits’s coil
9) Packing type
10) Defrost A Air E ElectricalHG Hot GasHG+E Hot Gas + Electrical
11) Fin material/protection AL=aluminium, EP=epoxy coated aluminium, CF=cataphoresis)
12) Standard Fin Spacing4 4 mm5.5 5,5 mm7 7 mm10 10 mm12 12 mm
13)Tube material CU=copper)
14) Options
38The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 23/24
AlfaCubic Code description
General Alfa Select Air Legend
Description 1 Description 2
D D fan cabling (three phase) BSFT Basic Switch Board + Speed Control Temp. + Signal AL Aluminium fin
Y Y fan cabling (three phase) BI Basic Switch Board + Frequency Converter (Inverter) CU Copper fin
D/YD/Y fan cabling (three phase), single speed fanmotor
BSIBasic Switch Board + Frequency Converter (Inverter) +Signal
PR Pre-coated fin
S Single phase C Switch Board + Cooling fan SS Stainless steel tube
P Packaged on a pallet R Switch Board + Resistor TH Thermoguard treatmentCR Packaged in a crate F Switch Board + Cooling fan + Resistor CF Cataphoresis treatment
BO Packaged in a box PT Ammonia pump top SC Sub-cooling circuit
Feet Feet-mounted PB Ammonia pump bottom KW Spray water kit
SW Safety Switch AL Aluminium casing FL Flanges
CB Terminal Box SS Stainless Steel casing FH Fan ring heater
B Basic Switch Board AP Pre-painted Aluminium casing IS Insulated Drip Tray
BS Basic Switch Board + Signal PL Plastic casing RH Reheating coil
BP Basic Switch Board + Step Control Pressure E Electrical defrost SR Air socket adapter ring
BT Basic Switch Board + Step Control Temperature LE Low Electrical defrost CW Air thr ow fan cowling
BSPBasic Switch Board + Step Control Pressure +Signal
A Air Defrost ER 120° elbow reducer
BST Basic Switch Board + Step Control Temp. + Signal HG Hot Gas Defrost HN Hinged fan cowling
BFP Basic Switch Board + Speed Control Pressure HG+E Hot Gas Defrost + Electrical Defrost on drip tray ST AlfaStreamer
BFT Basic Switch Board + Speed Control Temperature W Water Defrost L Coil with left side connection
BSFP Basic Switch Board + Speed Control Pres. + Signal W+E Water Defrost + Electrical Defrost on drip tray R Coil with right side connection
Note: valid for the entire product range
39The PMA is subject to periodical updates, so please keep checking it. While every precaution has been taken, Alfa Laval assume no
responsibility for errors or omission, or for damage resulting from the information contained herein.
8/22/2019 Alfacubic- Alfa Laval[1]
http://slidepdf.com/reader/full/alfacubic-alfa-laval1 24/24
Alfa Laval in brief
Alfa Laval is a leading global provider
of specialized products and engi-
neered solutions.
Our equipment, systems and
services are dedicated to helpingcustomers to optimize the perform-
ance of their processes. Time and
time again.
We help our customers to heat,
cool, separate and transport prod-
ucts such as oil, water, chemicals,
beverages, foodstuffs, starch and
pharmaceuticals.
Our worldwide organization works
closely with customers in almost 100
countries to help them stay ahead.
How to contact Alfa Laval
Up-to-date Alfa Laval contact details
for all countries are always available
on our website at www.alfalaval.com