DIY 120W Multi Grinder 75mm UK - 268953 / EU - 953843 Mini ...
AL110 Halter to be used on all standard verge details Tolerance …€¦ · min actual pitch 1...
Transcript of AL110 Halter to be used on all standard verge details Tolerance …€¦ · min actual pitch 1...
FOR CURVED APPLICATIONS VERGE CLOSURE AND VERGE
CHANNEL CAN BE FACETTED ON SITE TO FOLLOW THE
CURVE BY NOTCHING VERTICAL LEGS AS REQUIRED
RUN SEAMING TOOL
ON OVERLAP EDGE
PRIOR TO FITTING
VERGE CHANNEL
VERGE CHANNEL RIVETTED TO EUROSEAM AT
APPROX 400MM CENTRES USING 4.8 X 12MM RIVETS.
NB: DO NOT RIVET AT HALTER POSITION BUT CENTRALLY
BETWEEN HALTERS.
Verge Flashing
Only use if flashings requirements can be site
measured before ordering.
Verge
Channel
Verge
Closure
Verge Clip
Tolerance Detail (recommended)
No Tolerance Detail
VERGE CHANNEL RIVETTED TO EUROSEAM AT
APPROX 400MM CENTRES USING 4.8 X 12MM RIVETS.
NB: DO NOT RIVET AT HALTER POSITION BUT CENTRALLY
BETWEEN HALTERS.
Verge Flashing
Verge
Channel
AL110
Halter
Verge Clip
AL110 Halter to be used on all standard verge details
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
Recommended Max 150mm
Aluminium apron flashing
Pan support filler (self
adhesive base)
Verge Halter Flashing
2mm Aluminium complete
with WT75 separation tape
to base and predrilled with
7mm dia hole to base.
ABUTMENT DETAIL
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
SYSTEM
"IN
STALLED
D
IM
EN
SIO
N" +
1m
m/-1m
m
SIN
GLE SKIN
±5m
m
±10m
m
DO
UBLE SKIN
VARIATIONS BETWEEN LINES OF HALTERS
PLAN VARIATIONS
N.B. APPLIES TO COMPLETE
LINE OF HALTERS ONLY
VERTICAL VARIATIONS
(I.E. STEP IN PURLIN RUNS)
SYSTEM INSTALLED
DIMENSIONS FOR STRAIGHT
SHEETS ARE:
ESA400 = 402MM
ESA300 = 302MM
ESA500 = 502MM
Notes
1. Lines of halters are set out at system installed dims.
NB: Curved sheets are set out at post curve dims, see
relevent section of manual.
2. Tolerances stated are recommended to enable
Euroseam elements to accomodate thermal movement
over the halters without locking & introducing unwanted
fixed points. It is assumed that the halter elements when
fixed in place will follow a straight line or single curve
over their entire length. Multiple curves resulting in dips
or sudden changes in slope may cause a transfer or fixed
point. It should be noted that the Euroseam system is not
self levelling and will follow undulations or changes in
position within the supporting structure.
3. If there is an angular difference between the sheet and
the supports in some cases a wider bearer will be
required for the halter.
±5m
m
L L
±
1
°
±
1
°
±1m
m
±
1
°
VARIATIONS IN ONE
LINE OF HALTERS
HALTERS MUST BE VERTICAL
ON LINE OF ROOF PITCH
HALTERS MUST NOT
BE SET OUT OF LINE
LINE OF ROOF PITCH
VERTICAL VARIATIONS OF
THE HALTER HEADS IN LINE
(OVER THREE PURLINS)
LINE OF ROOF PITCH/CURVE
PLAN VARIATIONS OF
HALTER IN LINE
(OVER THREE PURLINS)
STAINLESS STEEL
FIXING TO SUIT
STRUCTURE
EUROSEAM
FORMATION
AFTER
SEAMING
ARROW ON BASE DENOTES
FIXING DIRECTION
SS110 HALTER
L = HALTER SPACING
IE PURLIN OR SPACER
CENTRES
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
EUROSEAM (ES400 or
ES300 IN MINIMUM
0.9mm ALUMINIUM)
ECZIP-SS110
HALTER
SECTION AT INTERMEDIATE
SUPPORTS, END LAPS
AND SHEET ENDS
SECTION A-A
The above detail has been tested in accordance with ACR(M)001:2005 to meet the requirements for
Non-fragile Class B at all purlin centres up to 2.1M, on straight sheet, curved sheet and up to 1.8M at hips.
A
AHALTERS FIXED USING AT LEAST 2 RECOMMENDED
FIXINGS. MINIMUM DISTANCE FOR SHEET EDGE FROM
HALTER OF 50MM. SEE ALSO RECOMMENDATIONS FOR
CANTILEVERS AND FIXING CONTAINED IN THE
CURRENT ISSUE OF THE EUROSEAM TECHNICAL
MANUAL.
EUROSEAM HALTERS FIXED USING MINIMUM OF 2 RECOMMENDED FIXINGS.
THE SHEET LAP SHOULD BE CLOSED USING THE EUROCLAD MST SEAMING
TOOL ACCORDING TO STANDARD PRACTICE, AS RECOMMENDED IN THE
CURRENT ISSUE OF THE EUROSEAM TECHNICAL MANUAL. FITTING OF THE
STANDARD VERGE DETAIL ACCESSORY PARTS IS NOT REQUIRED FOR
NON-FRAGILITY CLASSIFICATION B. THEY WILL, WHEN FITTED IMPROVE THE
PERFORMANCE. EUROSEAM SHOULD BE CONSIDERED NON-FRAGILE UNTIL
SHEET OVERLAPS ARE CLOSED USING THE MST.
NB:THIS NON-FRAGILE CLASSIFICATION DOES NOT APPLY TO HALTERS
FITTED DIRECT TO TIMBER. IF FITTED TO A TIMBER DECK, THE DECK SHOULD
PROVIDE FOR REQUIRED SAFETY PERFORMANCES IN ITS OWN RIGHT.
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
M
O
VEM
EN
T
M
O
VEM
EN
T
M
O
VEM
EN
T
M
O
VEM
EN
T
M
O
V
E
M
E
N
T
M
O
V
E
M
E
N
T
M
O
VEM
EN
T
M
O
VEM
EN
T
Mid position curved
intersection
Barrel vault crown
Soaker penetrations
Fixed Point
Sliding Ridge
Fixed Point
Sliding Ridge
Fixed Point
EXTENDED UPSTAND > 3 sheet widths
Fixed Point
UPSTAND SOAKER MAX 3 SHEET WIDTHS
Fixed Point
Fixed Point Fixed Point
Fixed Point
Fixed Point
RID
GE
PO
SITIO
N
STAINLESS STEEL NUT AND BOLT (M10)
ECZIP-A110 HALTER
SHEET
S/STL OR ALUM
RIVET THROUGH
SMALL ROLL OF
SHEET MODULE
FOLLOWING
ECZIP-A110 HALTER
FOR LOADS UP TO 0.524kN USE 1 RIVET
FOR LOADS 0.525kN to 1.04kN USE 2 RIVETS
FOR LOADS 1.05kN to 3.14 USE 1 M10 NUT AND BOLT
FOR LOADS HIGHER THAN 3.14kN REFER TO EUROCLAD TECHNICAL
FIXED POINT LOAD CALCULATION:
The fixed point load must be calculated for each slope. Please
contact Euroclad Technical for further guidance.
4.8mm dia
M
O
VEM
EN
T
Typical arrangement for straight
pitch Long slope or higher pitch.
Fixed Point
M
O
VEM
EN
T
Sliding Ridge
AL110 Halter to be used on fixed point locations
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
MIN ACTUAL PITCH 1 DEGREE
Max 300mm - Min 75mm
!
SHEET ENDS TO BE TURNED UP
TO PROVIDE MOISTURE DAM
ALLOW ADEQUATE CLEARANCE TO
ALLOW EFFECTIVE USE OF TURN UP TOOL.
RIDGE ZED - ECZIP_RZ5
RIDGE CLOSURE FIXED TO
RIDGE ZED MIN 1 RIVET
75
EUROSEAM
RIDGE ZED, CLOSURE & FILLER OMITTED FOR CLARITY.
EUROSEAM SLIDING CLIP ECZIP_SC50
EUROCLAD RIDGE FLASHING FIXED TO SLIDING CLIP
RIDGE FILLER
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
ECZIP_AL110 ALUMINIUM HALTER
WITH SEPARATION TAPE TO BASE
NB: 2nd RIDGE ZED REQUIRED TO SUPPORT FLASHING
DEPENDENT ON RIDGE FLASHING SIZE AND GAUGE AS
FOLLOWS:
0.9MM Al. - "DIM X" > 250MM.
1.6MM - Al. - "DIM X" > 450MM
2MM Al. - "DIM X" > 550MM
3MM Al - "DIM X" > 600MM
DIM "X"
RIDGE ZED SUPPORTING FLASHING
EUROCLAD RIDGE FLASHING
FIXED TO RIDGE ZED
TURN UP SHEET
ECZIP_AL110 ALUMINIUM HALTER
WITH SEPARATION TAPE TO BASE
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
RIDGE CLOSURE & FILLER
FIXED POINT
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
AL110 HALTER
EUROSEAM SHEET UPSTAND
RIDGE ZED
RIDGE CLOSURE
RIDGE FILLER
RIDGE ZED FIXED TO SHEET UPSTAND (DO NOT
POSITION DIRECTLY ABOVE HALTER)
RIDGE CLOSURE FIXED TO
BACK LEG OF RIDGE ZED
SHEET END TURNED UP
RIDGE FLASHING
FIXED TO RIDGE ZED
HIP RIDGE FLASHING
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
RIDGE FILLER 1M
CUT TO LENGTH
RIDGE CLOSURE 2660MM
CUT TO LENGTH
AL110 HALTER
EUROSEAM SHEET UPSTAND
HIP RIDGE FLASHING
FIXED TO RIDGE ZED
HIP RIDGE FLASHING
RIDGE ZED FIXED TO SHEET UPSTAND
(DO NOT POSITION DIRECTLY ABOVE HALTER)
SHEET END TURNED UP
RIDGE ZED
RIDGE CLOSURE FIXED TO
BACK LEG OF RIDGE ZED
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
CLEADER RAIL FIXED TO BAR OR
TOP HAT SUPPORTING STRUCTURE
300MM MAX
IF THERE IS AN ANGULAR DIFFERENCE
BETWEEN THE SHEET AND THE SUPPORTS
IN SOME CASES A WIDER BEARER WILL
BE REQUIRED FOR THE HALTER.
1
0
0
6
0
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
RIGID BOARD INSULATION RECOMMENDED LOCALLY FOR
BARREL VAULT CROWNS WHEN THERE ARE LARGER THAN
NORMAL SPANS BETWEEN SUPPORTS AND GREATER RISK
OF DAMAGE FROM FOOT TRAFFICKING.
FIXED POINT
FIXED POINT
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
RIDGE ZED - ECZIP_RZ5
75
EUROSEAM
RIDGE ZED, CLOSURE & FILLER OMITTED FOR CLARITY.
EUROSEAM SLIDING CLIP ECZIP_SC50
EUROCLAD RIDGE FLASHING FIXED TO SLIDING CLIP
6
RIDGE FILLER
ECZIP_SS110 Stainless Steel
Halter
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
RIDGE CLOSURE FIXED TO
RIDGE ZED MIN 1 RIVET
EUROSEAM SLIDING CLIP ECZIP_SC50
RIDGE ZED SUPPORTING
RIDGE FLASHING
EUROCLAD RIDGE FLASHING FIXED TO SLIDING CLIP
TURN UP SHEET
ECZIP_SS110
Stainless Steel
Halter
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
RIDGE CLOSURE
& FILLER. (ALLOW SUFFICICIENT
CLEARANCE FOR ANTICIPATED
EXPANSION TO HALTER)
NB: FIXED POINT CREATED DOWNSLOPE
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
PAN SUPPORT FILLER
WITH SELF ADHESIVE
STRIP
HALTER ECZIP_SS110
CLEADER RAIL FIXED
TO SPACER RAILS OR
TOP HAT SUPPORTING
STRUCTURE
EUROSEAM ES400
SHEET UPSTAND
SHEET END TURNED
DOWN
NB: SECONDARY
STEELWORK
CLEADER/RAKED EAVES
BEAM REQUIRED IF
EUROSEAM SHEET
CANTILEVER FROM LAST
PURLIN SUPPORT
EXCEEDS 300MM
DRIP ANGLE & FILLER
RIVETTED TO SHEET
PAN PRIOR TO TURN
DOWN
PURLIN
300MM MAX
PURLIN
HALTER ECZIP_SS110
IF THERE IS AN ANGULAR DIFFERENCE BETWEEN
THE SHEET AND THE SUPPORTS IN SOME CASES
AN ALUMINIUM HALTER OR IN EXTREME CASES
A WIDER BEARER WILL BE REQUIRED.
1
0
0
6
0
Max 300MM
ECZIP_SS110 STAINLESS
STEEL HALTER
PAN SUPPORT FILLER
(SELF ADHESIVE BASE)
RECOMMENDED
DRIP ANGLE & FILLER
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
PURLINS (IF PRESENT)
TO PURLINS
TRIMMERS FIXED
PLAN ELEVATION
(ROOFLIGHT & CAPPING OMITTED FOR CLARITY)
MIN 100KG DENSITY
MINERAL FIBRE
NON-COMBUSTIBLE
INSULATION
RIGID SLAB
TO CLOSE SEAM
CUT BACK AND WELDED
EUROSEAM SHEET
B
B
AA
EUROSEAM SHEET
BEVEL CUT TO
WILL BE NO FIRE RISK DUE TO SITE WELDING
MUST BE REMOVED TO ENSURE THAT THERE
THAT ARE IN THE VICINITY OF THE JOINT
ANY MATERIALS THAT ARE COMBUSTIBLE
SEAL INNER FLASHING TO
INTERNAL FINISH TO PROVIDE
CONTINUITY OF VAPOUR CONTROL
SOAKER UPSTAND MOVES WITH SHEET
INNER FLASHING
& CAPPING FIXED
TO STRUCTURE &
INDEPENDENT TO
OUTER SOAKER
SECTION A-A
SECTION B-B
INNER FLASHING
& CAPPING FIXED
TO STRUCTURE &
INDEPENDENT TO
OUTER SOAKER
MIN 100KG DENSITY
MINERAL FIBRE
NON-COMBUSTIBLE
SEAL INNER FLASHING TO
INTERNAL FINISH TO PROVIDE
CONTINUITY OF VAPOUR CONTROL
ECZIP_SS110
STAINLESS
STEEL HALTER
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
ECZIP_SS110
STAINLESS
STEEL HALTER
ALLOW ADEQUATE CLEARANCE
FOR THERMAL MOVEMENT
BETWEEN INNER & OUTER
FLASHINGS
ESURE CONTINUITY OF
INSULATION AROUND
PENETRATION
INTERNAL FLASHING
SEALED TO PIPE/FLUE
TO PROVIDE
CONTINUITY OF
VAPOUR
CONTROL/AIR
TIGHTNESS.
MIN 100KG DENSITY
MINERAL FIBRE
NON-COMBUSTIBLE
INSULATION
RIGID SLAB
SEAL INNER FLASHING TO
INTERNAL FINISH TO PROVIDE
CONTINUITY OF VAPOUR CONTROL
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
ALUMINIUM EUROSEAM
SHEET
SHEETS SEAMED UP ON
SITE PRIOR TO
INSTALLATION
COMPRESSIBLE SEALING
TAPE BETWEEN SEAMS
QUILT INSULATION
NOTE: REMOVE ALL
COMBUSTIBLE
MATERIALS FROM THE
VICINITY OF THE WELD
DUE TO FIRE RISK FROM
SITE WELDING
RAKE CUT SHEETS
WELDED CONTINUOSLY
TO PRECUT AND SEAMED
SHEET. UPSTANDS AND
SHEET PROFILE WELDED
CLOSED.
FP = FIXED POINT
ALSO REFER TO DETAIL
OF SLIDING RIDGE
MIN 100KG DENSITY
MINERAL FIBRE
NON-COMBUSTIBLE
ALUMINIUM HALTER
FP
ALUMINIUM HALTER
FP
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
99.9514
100.0282
100.1565OVERLAP
NOTES
1. THE WELD MUST NOT CONNECT ADJACENT SHEETS BUT MUST START AND
FINISH AS SHOWN.
2. CONTINUOUS SUPPORT MUST BE GIVEN TO THE SHEETS IN THE VICINITY OF
THE WELD
END OF WELD
SS110 HALTER
HIGH DENSITY, NON-COMBUSTIBLE
SLAB INSULATION 300MM WIDE
VENTRED UNDER WELD.
D
I
R
E
C
T
I
O
N
O
F
L
A
Y
START OF WELD
100
M
IN
100m
m
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
2
2
0
m
m
1
8
0
m
m
1
8
0
m
m
2
2
0
m
m
OF LAY
DIRECTION
200M
M O
VERLAP
100m
m M
IN
HIGH DENSITY, NON-COMBUSTIBLE
SLAB INSULATION 300MM WIDE CENTRED
UNDER JOINT TO PROVIDE SUPPORT.
MASTIC END LAPS ARE ONLY SUITABLE FOR PITCHES > 5°.
FOR PITCHES < 5° A CONTINUOUSLY WELDED JOINT IS REQUIRED.
MASTIC MUST BE LOW MODULUS.
GUN APPLIED LOW MODULUS MASTIC.
4.8mm DIA ALUMINIUM
BLIND SEALED RIVETS
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
100 100
R
6
,
6
400
100
5,5
1,3
100
19 19
4
5
°
R
4
,
3
0,9
87 13 5758
1,7
75
39
EUROCLAD EUROSEAM ES400
0.9mm EXTERNAL SHEET
NOMINAL SHEET CLEARANCE ON SS110 HALTER
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
Consult with Euroclad for allowable loads per clamp.
Determine appropriate number of Clamps for all applicable loads.
39
75
21.16
Secured with 2 x stainless
steel M8 with cap heads
supplied
Multiple Clamps can be used between halters to spread loads more evenly.
See Component drawing
for detail of Clamp.
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
3,6
6
3,7
8,9
6
18,5
18,5
10
7,2
7,2
8,9
40
51,5
2
3
110
8,5
17
8,5
14,7
3
40
18,5
18,5
3
40
11.3
7
14
24,8
31,5
19,2
10,4
ECZIP_SS110 Stainless Steel Halter
SS110 Stainless Steel Halter
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
ECZIP_AL110 Aluminium Halter
110
5
1
1
2
°
3,5
60
HALTER BASE - PLAN VIEW
40
2 H
OLES Ø
7
60
20
10
10
20
(Supplied with separation tape to base)
AL110 Aluminium Halter
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
40
Brackets less than 260mm require 2 fixings diagonally opposite.
Brackets 260mm or more require 4 fixings.
< 260mm
≥ 260mm
40
33
34
60
59
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
40
27
1.5
1.5
2
20
SEE NOTES
S
E
E
N
O
T
E
S
MATERIAL:- ALUMINIUM 5M LONG
1. FOR CURVED
CUTTING OUT VERTICAL
FACETED ON SITE BY
CHANNEL TO BE
APPLICATIONS VERGE
2. PITCH & ANGLE OF
CUTOUT IS DEPENDENT
SECTION.
NOTES
VERGE CHANNEL - ECZIP_VCN5
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
VERGE CLIP - ECZIP_VCP2
MATERIAL:- ALUMINIUM 40MM LONG1
15.5
3
3
30
30
32
33
103
R
0
.
5
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
8
1.5371.5
65
1.5
49
9
4
5
°
R
2
.
5
R
0
.
7
5
R
0
.
3
5
S
E
E
N
O
T
E
S
SEE NOTES
MATERIAL:- ALUMINIUM 5M LONG
CUTOUT IS DEPENDENT
2. PITCH & ANGLE OF
APPLICATIONS VERGE
CLOSURE TO BE
FACETED ON SITE BY
CUTTING OUT VERTICAL
NOTES
1. FOR CURVED
SECTION.
ON RADIUS OF ROOF.
VERGE CLOSURE - ECZIP_VCL5
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
40
15
31.5
27.5
2
117
2
PLAN VIEW VERGE HALTER - ECZIP_VH2
69.5
40
HO
LE Ø
7
15
117
2
40
VERGE HALTER ECZIP_VH2
Supplied with WT75 separation tape to base
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
30
3
45
75
2.65
6
2
2
15
MATERIAL:- ALUMINIUM 5M LONG
RIDGE ZED - ECZIP_RZ5
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
67
25
22.8
1.2
1.2
29
4
MATERIAL:- ALUMINIUM 375MM & 5M LONG
RIDGE CLOSURE - ECZIP_KITRCPM400 & ECZIP_KITLC5M
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
COLOUR SIDE
40
74
MATERIAL:- COATED ALUMINIUM 0.9mm 375mm & 3M LONG
RIDGE CLOSURE COVER - ECZIP_KIT
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
2
63
6
Ø23.5
65°
3
2
.
5
°
29
5
0
MATERIAL:- ALUMINIUM 50mm LONG
SLIDING CLIP - ECZIP_SSC
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
FRONT VIEW
SIDE VIEW
25
73
SEE NOTES
15
15
73
RIDGE FILLER - ECZIP_KITRF400 LENGTH = 400MM
ECZIP_KITLF1M - HIPS, VALLEYS AND TAPERS COMPONENT SUPPLIED IN
1M LENGTH, CUT ON SITE TO SUIT REQUIRED LENGTH
MATERIAL = MP or HEAVY DUTY EPDM
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
FRONT VIEW
SIDE VIEW
50
39
SELF ADHESIVE STRIP - HP500 15 X 2MM
330
MATERIAL:HARDPACK (F.A.I.R. HIGH DENSITY MATERIAL )
KIT SHEET PAN SUPPORT FILLERS - ECZIP_SF_SS110-400 (old ref SF95_400): Length: 330mm
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
3
3
25
50
MATERIAL:- ALUMINIUM 5M LONG
DRIP ANGLE - ECZIP_DA5M
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
200200
6
EAVES FILLER FOR EUROSEAM ES400 -
ECZIP_EF400
6
79
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101
50
25
8
50
12
20.98
8.5
12
38
8.5
1 x stainless steel
M10 Bolt with
split washer
Secured with 2 x
stainless steel M8
with cap heads
40
MATERIAL:- ALUMINIUM 50mm LONG
SEAM CLAMP - ECZIP_SEAMCLAMP
38
TITLE: Euroseam Universal
Details & Components
DWG NO: ES_EDC1
DRAWN: PCl
DATE: April 16
CHECK: PCL
SCALE: NTS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euro Clad Ltd for
the purpose of guidance free of
charge. It is a suggested typical
detail and as such should not be
assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
Fax: +44 (0)2922 010 122
www.euroclad.com
Tel: +44 (0)2922 010 101