AKD5365 English Manual - AKM - Asahi Kasei Microdevices · AKD5365 is an evaluation board for the...

ASAHI KASEI [AKD5365]

<KM068901> 2006/08 - 1 -

GENERAL DESCRIPTION

AKD5365 is an evaluation board for the digital audio 24bit 96kHz A/D converter, AK5365. The AKD5365 includes the input circuit and also has a digital interface transmitter. Further, the AKD5365 can achieve the interface with digital audio systems via opt-connector.

Ordering guide

AKD5365 --- AK5365 Evaluation Board (Cable for connecting with printer port of IBM-AT compatible PC

and control software are packed with this.)

FUNCTION

• DIT with optical output • BNC connector for an external clock input • 10pin Header for serial control mode

LIN1-5

RIN1-5

AVDD,DVDD

AK4103(DIT)

OptOut

ClockGenerator ROM Data

10pin Header

ControlData

10pin Header

AVSS,DVSS

AK5365

Figure 1. AKD5365 Block Diagram

* Circuit diagram and PCB layout are attached at the end of this manual.

AK5365 Evaluation Board Rev.AAKD5365


<KM068901> 2006/08 - 2 -

1. Evaluation Board Manual

Operation sequence 1) Set up the power supply lines. [AVDD] (Red) = 4.75 ∼ 5.25V: for AVDD of AK5365 (typ. 5.0V)

[TVDD] (Orange) = 3.0 ∼ 5.25V: for DVDD of AK5365 (typ. 3.3V) [D3V] (Orange) = 3.0 ∼ 5.25V: for 74LVC541 (typ. 3.3V) [VCC] (Red) = 5V: for logic [AGND] (Black) = 0V: for analog ground [DGND] (Black) = 0V: for logic ground

Each supply line should be distributed from the power supply unit. D3V and TVDD must be same voltage level.

2) Set up the evaluation mode, jumper pins and DIP switches. (See the followings.) 3) Power on. The AK5365 and AK4103 should be reset once bringing SW2 = “L” upon power-up.

Evaluation mode

(1) Slave Mode

When evaluating the AK5365 using the AK4103, the setting of the AK5365’s audio interface format should be the same as the AK4103’s format. The DIF setting of the AK5365 (No.1 of SW1 (I2C) in parallel mode, DIF bit in serial mode) should be the same as the DIF setting of the AK4103 (No.1 of SW3). About the AK5365’s audio interface format, refer to AK5365’s datasheet. About the AK4103’s audio interface format, see Table3.

(1-1) A/D evaluation using DIT function of AK4103

PORT1 (DIT) is used. DIT generates audio bi-phase signal from received data and which is output through optical connector (TOTX176). It is possible to connect AKM’s D/A converter evaluation boards on the digital-amplifier which equips DIR input. Nothing should be connected to PORT2 (ROM). In case of using external clock through a BNC connector (J13), select EXT on JP8 (CLK) and short JP6 (XTE) and open JP9 (EXT).

JP8CLK

JP2LRCK

JP4BICK

XTL

EXT

JP6XTE

JP9EXT


<KM068901> 2006/08 - 3 -

(2) Master Mode

(2-1) A/D evaluation using DIT function of AK4103

PORT1 (DIT) is used. DIT generates audio bi-phase signal from received data and which is output through optical connector (TOTX176). It is possible to connect AKM’s D/A converter evaluation boards on the digital-amplifier which equips DIR input. Nothing should be connected to PORT2 (ROM). In case of using external clock through a BNC connector (J13), select EXT on JP8 (CLK) and short JP6 (XTE) and open JP9 (EXT).

JP8CLK

JP2LRCK

JP4BICK

XTL

EXT

JP6XTE

JP9EXT

Other jumper pins set up 1. JP1 (GND): Analog ground and Digital ground OPEN: Separated. SHORT: Common. (The connector “DGND” can be open.) <Default> 2. JP3 (M/S): Select Master/Slave mode for AK5365 SLAVE: Slave mode <Default> MASTER: Master mode 3. JP5 (TVDD): Select DVDD for AK5365 REG: Supply from regulator TVDD: Supply from TVDD connector <Default> 4. JP7 (MCLK): MCLK Frequency for 74HC4040 256: MCLK is 256fs. (=12.288MHz@fs=48kHz) <Default> 512: MCLK is 512fs. (=24.576MHz@fs=48kHz)


<KM068901> 2006/08 - 4 -

DIP Switch set up [SW1] (MODE1): Setting the evaluation mode for AK5365 ON is “H”, OFF is “L”. Default is all “L”.

No. Name OFF (“L”) ON (“H”) 1 I2C Fixed to “L” 2 CAD0 Fixed to “L” 3 CAD1 Fixed to “L” 4 DIF Fixed to “L” 5 SEL2 6 SEL1 7 SEL0

See Table 2

8 ALC ALC Disable ALC Enable Table 1. Mode Setting of AK5365

SEL2 SEL1 SEL0 Input Selector OFF OFF OFF LIN1 / RIN1 Default OFF OFF ON LIN2 / RIN2 OFF ON OFF LIN3 / RIN3 OFF ON ON LIN4 / RIN4 ON OFF OFF LIN5 / RIN5

Table 2. Input Selector [SW3] (MODE2): Setting the evaluation mode for AK4103 ON is “H”, OFF is “L”. Default is all “L”.

No. Name OFF (“L”) ON (“H”) 1 DIF 24bit, MSB justified 24bit, I2S Compatible 2 CKS1 3 CKS0 See Table 4

Table 3. Mode Setting of AK4103

Mode CKS1 CKS0 MCLK fs 0 OFF OFF 256fs ∼ 96kHz Default 1 OFF ON N/A N/A 2 ON OFF 512fs ∼ 48kHz 3 ON ON 384fs ∼ 48kHz

Table 4. MCLK Frequency Setting of AK4103

The function of the toggle SW

Upper-side is “H” and lower-side is “L”. [SW2] (PDN): Resets the AK5365 and AK4103. Keep “H” during normal operation. [SW4] (SMUTE): Soft mute of AK5365.


<KM068901> 2006/08 - 5 -

Serial Control The AK5365 can be controlled via the printer port (parallel port) of IBM-AT compatible PC. Connect PORT3 (CTRL) with PC by 10-line flat cable packed with the AKD5365. The control software packed with this evaluation board does not support I2C control.

ConnectCSNCCLKCDTI

10pin Header10pinConnector

10 wireflat cable

PC AKD5365

Figure 2. Connect of 10-line flat cable

Input/Output Circuits

(1) Input Circuit

Analog signal is input to LIN1-5/RIN1-5 pins via J1 ∼ J12 connectors.

RIN4

+

C261u

J7RIN3

LIN4

+

C271u

+C201u

RIN5

J12LIN5

J5LIN2

J1RIN1

LIN5

RIN2

+

C211u

+

C291u

LIN2

+

C301u

LIN1

RIN3

RIN1

J8LIN3

J10LIN4

J9RIN4

J2LIN1

LIN3

+

C281u

+

C311u

+

C241u

+

C231u

J4RIN2

J11RIN5

Figure 3. LIN1-5/RIN1-5 Input circuits


<KM068901> 2006/08 - 6 -

The cut-off frequency of the input circuit on this evaluation board is as below. When changing the cut-off frequency, change the constant of the each resistor and capacitor.

(1) The cut-off frequency of HPF in front of the Pre-Amp: fc = 3.4Hz (R = 47kΩ, C = 1µF)

(2) The cut-off frequency of HPF, which is composed by the input resistance of the IPGAL/R pins and the capacitor

of between the Pre-Amp output and the IPGA input: fc = 3.4Hz. (R = 10kΩ, C = 4.7µF)

(2) Output Circuit

Signal of LOUT and ROUT pins are output via J3 (LOUT) and J6 (ROUT).

+

C2522u

J6ROUT

R2347k

R22220

R20220

LOUT

R2147k

+

C2222u

ROUT

J3LOUT

Figure 4. LOUT/ROUT Output circuits

* AKM assumes no responsibility for the trouble when using the circuit examples.


<KM068901> 2006/08 - 7 -

Control Software Manual

Set-up of evaluation board and control software

1. Set up the AKD5365 according to previous term.

2. Connect IBM-AT compatible PC with AKD5365 by 10-line type flat cable (packed with AKD5365). Take care of the

direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used on Windows 2000/XP. Please refer “Installation Manual of Control Software Driver by AKM device control software”. In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.)

3. Insert the CD-ROM labeled “AKD5365 Evaluation Kit” into the CD-ROM drive.

4. Access the CD-ROM drive and double-click the icon of “akd5365.exe” to set up the control program.

5. Then please evaluate according to the follows.

Operation flow

Keep the following flow.

1. Set up the control program according to explanation above. 2. Click “Port Reset” button.

Explanation of each buttons

1. [Port Reset]: Set up the USB interface board (AKDUSBIF-A). 2. [Write default]: Initialize the register of AK5365. 3. [All Write]: Write all registers that is currently displayed. 4. [Function1]: Dialog to write data by keyboard operation. 5. [Function2]: Dialog to write data by keyboard operation. 6. [Function3]: The sequence of register setting can be set and executed. 7. [Function4]: The sequence that is created on [Function3] can be assigned to buttons and executed. 8. [Function5]: The register setting that is created by [SAVE] function on main window

can be assigned to buttons and executed. 9. [SAVE]: Save the current register setting. 10. [OPEN]: Write the saved values to all register. 11. [Write]: Dialog to write data by mouse operation.

Indication of data

Input data is indicated on the register map. Red letter indicates “H” or “1” and blue one indicates “L” or “0”. Blank is the part that is not defined in the datasheet.


<KM068901> 2006/08 - 8 -

Explanation of each dialog 1. [Write Dialog]: Dialog to write data by mouse operation

There are dialogs corresponding to each register.

Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data becomes “H” or “1”. If not, “L” or “0”.

When writing the input data to AK5365, click [OK] button. If not, click [Cancel] button.

2. [Function1 Dialog]: Dialog to write data by keyboard operation Address Box: Input registers address in 2 figures of hexadecimal. Data Box: Input registers data in 2 figures of hexadecimal.

When writing the input data to AK5365, click [OK] button. If not, click [Cancel] button. 3. [Function2 Dialog]: Dialog to evaluate ATT

This is a dialog corresponding to address: 04H, 05H.

Address Box: Input registers address in 2 figures of hexadecimal. Start Data Box: Input starts data in 2 figures of hexadecimal. End Data Box: Input end data in 2 figures of hexadecimal. Interval Box: Data is written to AK5365 by this interval. Step Box: Data changes by this step. Mode Select Box:

With checking this check box, data reaches end data, and returns to start data. [Example] Start Data = 00, End Data = 09

Data flow: 00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00 Without checking this check box, data reaches end data, but does not return to start data. [Example] Start Data = 00, End Data = 09

Data flow: 00 01 02 03 04 05 06 07 08 09

When writing the input data to AK5365, click [OK] button. If not, click [Cancel] button.


<KM068901> 2006/08 - 9 -

4. [Save] and [Open] 4-1. [Save] Save the current register setting data. The extension of file name is “akr”. (Operation flow) (1) Click [Save] Button. (2) Set the file name and push [Save] Button. The extension of file name is “akr”. 4-2. [Open]

The register setting data saved by [Save] is written to AK5365. The file type is the same as [Save]. (Operation flow) (1) Click [Open] Button. (2) Select the file (*.akr) and Click [Open] Button.


<KM068901> 2006/08 - 10 -

5. [Function3 Dialog] The sequence of register setting can be set and executed.

(1) Click [F3] Button. (2) Set the control sequence.

Set the address, Data and Interval time. Set “-1” to the address of the step where the sequence should be paused. (3) Click [Start] button. Then this sequence is executed.

The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step.

This sequence can be saved and opened by [Save] and [Open] button on the [Function3] window. The extension of file name is “aks”.

Figure 1. Window of [F3]


<KM068901> 2006/08 - 11 -

6. [Function4 Dialog] The sequence that is created on [Function3] can be assigned to buttons and executed. When [F4] button is clicked, the window as shown in Figure 2 opens.

Figure 2. [F4] window


<KM068901> 2006/08 - 12 -

6-1. [OPEN] buttons on left side and [START] buttons (1) Click [OPEN] button and select the sequence file (*.aks). The sequence file name is displayed as shown in Figure 3.

Figure 3. [F4] window(2)

(2) Click [START] button, then the sequence is executed. 6-2. [SAVE] and [OPEN] buttons on right side

[SAVE]: The sequence file names can assign be saved. The file name is *.ak4.

[OPEN]: The sequence file names assign that are saved in *.ak4 are loaded. 6-3. Note (1) [Function4] doesn't support the pause function of sequence function. (2) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (3) When the sequence is changed in [Function3], the file should be loaded again in order to reflect the change.


<KM068901> 2006/08 - 13 -

7. [Function5 Dialog] The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. When [F5] button is clicked, the following window as shown in Figure 4opens.

Figure 4. [F5] window

7-1. [OPEN] buttons on left side and [WRITE] button (1) Click [OPEN] button and select the register setting file (*.akr). (2) Click [WRITE] button, then the register setting is executed. 7-2. [SAVE] and [OPEN] buttons on right side

[SAVE]: The register setting file names assign can be saved. The file name is *.ak5.

[OPEN]: The register setting file names assign that are saved in *.ak5 are loaded. 7-3. Note (1) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (2) When the register setting is changed by [Save] Button in main window, the file should be loaded again in order to

reflect the change.


<KM068901> 2006/08 - 14 -

MEASUREMENT RESULTS [Measurement condition]

• Measurement unit : Audio Precision, System Two Cascade • MCLK : 256fs • BICK : 64fs • fs : 48kHz, 96kHz • Bit : 24bit • Power Supply : AVDD = 5.0V, DVDD = 3.3V • Interface : DIT • Temperature : Room • External Condition : Input resistor (Ri) = 47kΩ, Feedback resistor (Rf) = 24kΩ • IPGA Gain : 0dB

Parameter Result (Lch / Rch) Unit Pre-Amp Characteristics: S/(N+D) 105.8 / 102.5 dB S/N (A-weighted) 108.6 / 108.6 dB ADC Analog Input Characteristics: LIN1/RIN1 → Pre-Amp → IPGA → ADC, IPGA=0dB, ALC=OFF S/(N+D) (-0.5dB Input)

fs=48kHz fs=96kHz

95.6 / 96.6 91.2 / 91.9

dB dB

D-Range (-60dB Input)

fs=48kHz, A-weighted fs=96kHz

103.3 / 103.4 98.6 / 98.6

dB dB

S/N

fs=48kHz, A-weighted fs=96kHz

103.3 / 103.4 98.6 / 98.6

dB dB

Interchannel Isolation 115.5 / 116.5 dB


<KM068901> 2006/08 - 15 -

[ADC Plot : fs=48kHz]

AK5365 THD+N vs. Input LevelAVDD=5.0V, DVDD=3.3V, fs=48kHz, fin=1kHz

-120 +0-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

dBr

-120

-80

-116

-112

-108

-104

-100

-96

-92

-88

-84

dBFS

Figure 1. THD+N vs. Input Level

AK5365 THD+N vs. Input FrequencyAVDD=5.0V, DVDD=3.3V, fs=48kHz, Input=-0.5dBr

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-110

-80

-107

-104

-101

-98

-95

-92

-89

-86

-83

dBFS

Figure 2. THD+N vs. Input Frequency


<KM068901> 2006/08 - 16 -

AK5365 LinearityAVDD=5.0V, DVDD=3.3V, fs=48kHz, fin=1kHz

-140 +0-130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

dBr

-140

+0

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

Figure 3. Linearity

AK5365 Frequency ResponseAVDD=5.0V, DVDD=3.3V, fs=48kHz, Input=0dBr

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-0.5

+0.5

-0.4

-0.3

-0.2

-0.1

+0

+0.1

+0.2

+0.3

+0.4

dBFS

Figure 4. Frequency Response


<KM068901> 2006/08 - 17 -

AK5365 CrosstalkAVDD=5.0V, DVDD=3.3V, fs=48kHz, Input=-0.5dBr

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-150

-80

-145

-140

-135

-130

-125

-120

-115

-110

-105

-100

-95

-90

-85

dB

Figure 5. Crosstalk

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=48kHz, Input=-0.5dBr, fin=1kHz

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

Figure 6. FFT Plot


<KM068901> 2006/08 - 18 -

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=48kHz, Input=-60dBr, f in=1kHz

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

Figure 7. FFT Plot

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=48kHz, f in=None

20 20k50 100 200 500 1k 2k 5k 10k

Hz

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

Figure 8. FFT Plot


<KM068901> 2006/08 - 19 -

[ADC Plot : fs=96kHz]

AK5365 THD+N vs. Input LevelAVDD=5.0V, DVDD=3.3V, fs=96kHz, fin=1kHz

-120 +0-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

dBr

-120

-80

-116

-112

-108

-104

-100

-96

-92

-88

-84

dBFS

Figure 9. THD+N vs. Input Level

AK5365 THD+N vs. Input FrequencyAVDD=5.0V, DVDD=3.3V, fs=96kHz, Input=-0.5dBr

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

-110

-80

-108

-106

-104

-102

-100

-98

-96

-94

-92

-90

-88

-86

-84

-82

dBFS

Figure 10. THD+N vs. Input Frequency


<KM068901> 2006/08 - 20 -

AK5365 LinearityAVDD=5.0V, DVDD=3.3V, fs=96kHz, fin=1kHz

-140 +0-130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

dBr

-140

+0

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

Figure 11. Linearity

AK5365 Frequency ResponseAVDD=5.0V, DVDD=3.3V, fs=96kHz, Input=0dBr

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

-0.5

+0.5

-0.4

-0.3

-0.2

-0.1

+0

+0.1

+0.2

+0.3

+0.4

dBFS

Figure 12. Frequency Response


<KM068901> 2006/08 - 21 -

AK5365 CrosstalkAVDD=5.0V, DVDD=3.3V, fs=96kHz, Input=-0.5dBr

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

-150

-70

-145

-140

-135

-130

-125

-120

-115

-110

-105

-100

-95

-90

-85

-80

-75

dB

Figure 13. Crosstalk

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=96kHz, Input=-0.5dBr, fin=1kHz

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

Figure 14. FFT Plot


<KM068901> 2006/08 - 22 -

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=96kHz, Input=-60dBr, f in=1kHz

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

Figure 15. FFT Plot

AK5365 FFT PlotAVDD=5.0V, DVDD=3.3V, fs=96kHz, f in=None

-180

+0

-170

-160

-150

-140

-130

-120

-110

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

dBFS

20 40k50 100 200 500 1k 2k 5k 10k 20k

Hz

Figure 16. FFT Plot


<KM068901> 2006/08 - 23 -

Revision History

IMPORTANT NOTICE • These products and their specifications are subject to change without notice. Before considering any use or

application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status.

• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein.

• Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials.

• AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or

for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.

(b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.

• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification.

Date (YY/MM/DD)

Manual Revision

Board Revision

Reason Contents

02/04/25 KM068900 0 First Edition 06/08/29 KM068901 1 Circuit Change C32, C33: open 5p

A

A

B

B

C

C

D

D

E

E

E E

D D

C C

B B

A A

Title

Size Document Number Rev

Date: Sheet ofAK5365 1

AKD5365 Rev.A 44LQFPA3

1 1Tuesday, August 29, 2006

Title





Title





+

C24.7u

+

C24.7u

+

C810u

+

C810u

C40.1uC40.1u

R847kR847k

R447kR447k

R747kR747k

R947kR947k

C30.1uC30.1u

R1047kR1047k

R247kR247k

+C14.7u

+C14.7u

R1124kR1124k

R547kR547k

1

2

3

4

5

6

7

8

9

10

11

12

CN3CN3

R1224kR1224k

R147kR147k

R347kR347k

25

26

27

28

29

30

31

32

33

34

35

36

CN2CN2

373839404142434445464748

CN1CN1

LIN51

TEST12

LIN43

TEST24

LIN35

TEST36

LIN27

TEST48

LIN19

LOPIN10

LOUT11

IPG

AL

12

IPG

AR

13

RO

UT

14

RO

PIN

15

AV

DD

16

AV

SS

17

VC

OM

18

DV

SS

19

DV

DD

20

SD

TO21

BIC

K22

LRCK 23

MCLK 24

PDN 25

ALC 26

SMUTE 27

SEL0 28

SEL1 29

SEL2 30

CDTI/SDA 31

CCLK/SCL 32

CSN/CAD1 33

CTR

L34

M/S

35

RIN

136

TES

T537

RIN

238

TES

T639

RIN

340

TES

T741

RIN

442

TES

T843

RIN

544

U1AK5365

U1AK5365

+

C610u

+

C610u

+

C72.2u

+

C72.2u

13 14 15 16 17 18 19 20 21 22 23 24

CN4CN4

R647kR647k

C50.1uC50.1u

A

A

B

B

C

C

D

D

E

E

E E

D D

C C

B B

A A

D3V

TVDD

AVDD

5365_PDN

5365_SLRCK

LOUT

SMUTE

CAD0

CA

D0

SEL1

RIN

2

CDTI

RO

UT

DIF

SEL0

BICK

ALC

LIN3

CSN

LIN4

SEL2

M/S

RIN

3

ALC

I2C

CCLK

SEL2

5365_MCLK

RIN

1

LIN2

RIN

5

LIN5

SEL0

LRCK

M/S

CAD1

SD

TO

RIN

4

LIN1

SEL1

DIF

I2C

5365_SBICK

Title



AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


AGNDDGND

MASTERSLAVE

I2C

CAD1DIFSEL2

ALCSEL0SEL1

TVDD

REG

CAD0

1 2

L2(short)L2(short)

12345678

161514131211109

SW1

MODE1

SW1

MODE1

C110.1uC110.1u

R9 51R9 51

JP1GNDJP1GND

1 2

L1(short)

L1(short)

JP5TVDDJP5TVDD

R15 51R15 51

R1751R17511

2

+C1447u

+C1447u

JP4BICKJP4BICK

12

+ C1347u

+ C1347u

R34(open)R34(open)

13 14 15 16 17 18 19 20 21 22 23 24

CN4CN4

373839404142434445464748

CN1CN1

25

26

27

28

29

30

31

32

33

34

35

36

CN3CN3

IN OUT

GN

D

T1TA48M33FT1TA48M33FJP3

M/SJP3M/S

C100.1uC100.1u

JP2LRCKJP2LRCK

123456789

RP1

47k

RP1

47k

R7 51R7 51

R14 51R14 51

1

2

3

4

5

6

7

8

9

10

11

12

CN2CN2

A

A

B

B

C

C

D

D

E

E

E E

D D

C C

B B

A A

VCC

VCC

VCC

VCC

VCC

MCLK

MCLK

DIT_DIF

CKS1

CKS0

PDN

DIT_DIFCKS1

SDTO

BICK

LRCK

CKS0

Title


Date: Sheet ofDIT AK4103 1

AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


SDTOLRCKBICKMCLK

HL

CKS0CKS1DIF

A12

A23

A34

A45

A56

A67

A78

A89

G11

G219

Y1 18

Y2 17

Y3 16

Y4 15

Y5 14

Y6 13

Y7 12

Y8 11

VCC 20

GND 10

U4

74HCT541

U4

74HCT541

R1810kR1810k

1 2U2A

74HC14

U2A

74HC14

321

RP2

47k

RP2

47k

C170.1uC170.1u

C150.1uC150.1u

R191kR191k

3 4U2B

74HC14

U2B

74HC14

GND1 IF2 VCC3 IN4 5 5

6 6

PORT1

DIT

PORT1

DIT

21

D1HSU119D1HSU119

+C1910u+C1910u

V11

TRANS2

RESETN3

MCLK4

SDTI5

BICK6

LRCK7

FS0/CSN8

FS1/CDTI9

FS2/CCLK10

FS3/CDTO11

C112 ANS 13

BLS 14

CKS0 15

CKS1 16

DVDD 17

DVSS 18

TXN 19

TXP 20

DIF0 21

DIF1 22

DIF2 23

U1 24

U3

AK4103

U3

AK4103

C160.1uC160.1u

12345 6

78910

PORT2

ROM

PORT2

ROM

213

SW2PDNSW2PDN

123

654

SW3

MODE2

SW3

MODE2

C180.1uC180.1u

A

A

B

B

C

C

D

D

E

E

E E

D D

C C

B B

A A

RIN2

RIN1

RIN3

RIN4

RIN5

LIN2

LIN1

LIN3

LIN4

LIN5

LOUT

ROUT

Title


Date: Sheet ofInput/Output 1

AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


J8LIN3J8LIN3

J3LOUTJ3LOUT

+

C231u

+

C231u

J2LIN1J2LIN1

+

C211u

+

C211u

J9RIN4J9RIN4

+

C2522u

+

C2522u

+

C301u

+

C301u

+

C261u

+

C261u

+

C201u

+

C201u

J10LIN4J10LIN4

R20220R20220

J4RIN2J4RIN2 J6

ROUTJ6ROUT

+

C291u

+

C291u

+

C281u

+

C281u

R2347kR2347k

J11RIN5J11RIN5

+

C271u

+

C271u

R22220R22220

J1RIN1J1RIN1

J7RIN3J7RIN3

+

C241u

+

C241u

J12LIN5J12LIN5

+

C2222u

+

C2222u

+

C311u

+

C311u

J5LIN2J5LIN2

R2147kR2147k

A

A

B

B

C

C

D

D

E

E

E E

D D

C C

B B

A A

VCC

VCC

VCC

D3V

VCC

D3V

D3V

MCLK

I2C

CDTI

CAD1

5365_SBICK

5365_SLRCK

5365_MCLK

PDN

SMUTE

CCLK

CSN

5365_PDN

Title


Date: Sheet ofLOGIC 1

AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


Title



AKD5365 Rev.AA3


for 74HC14, 74HCU04, 74HC4040 74AC74, 74HCT157, 74LS07

256

EXTXTL

512

CSNCCLK/SCL

SDA(ACK)

L H

CDTI/SDA

12345 6

78910

PORT3

CTRL

PORT3

CTRL

D2 Q 5

CLK3

Q 6

PR

4C

L1

U7A74AC74U7A74AC74

+C4347u

+C4347u

R331.8KR331.8K

C335pC335p

9 8U2D

74HC14

U2D

74HC14

C380.1uC380.1u

J13EXTJ13EXT

5 6U2C

74HC14

U2C

74HC14

3 4U5B

74HCU04

U5B

74HCU04

+C3647u

+C3647u

C325pC325p

R2810kR2810k

R26 10kR26 10k

R32 470R32 470

213

SW4SMUTESW4SMUTE

R2551R2551

C420.1uC420.1u

R27 470R27 470

JP9EXTJP9EXT

JP6XTEJP6XTE

1A21B32A52B63A113B104A144B13

A/B1G15

1Y 4

2Y 7

3Y 9

4Y 12

U9

74HCT157

U9

74HCT157

CLK10

RST11

Q1 9Q2 7Q3 6Q4 5Q5 3Q6 2Q7 4Q8 13Q9 12

Q10 14Q11 15Q12 1

U6

74HC4040

U6

74HC4040

C390.1uC390.1u

1 2U5A

74HCU04

U5A

74HCU04

R29 10kR29 10k

21

D2HSU119D2HSU119

C400.1uC400.1u

R24

1M

R24

1M

X112.288MHzX112.288MHz

C350.1uC350.1u

C340.1uC340.1u

JP8

CLK

JP8

CLK

JP7MCLKJP7MCLK

C370.1uC370.1u

R31 10kR31 10k

R30 470R30 470

1 2U10A

74LS07

U10A

74LS07

C410.1uC410.1u

A12

A23

A34

A45

A56

A67

A78

A89

G11

G219

Y1 18

Y2 17

Y3 16

Y4 15

Y5 14

Y6 13

Y7 12

Y8 11

VCC 20

GND 10

U8

74LVC541

U8

74LVC541

AKD5365 English Manual - AKM - Asahi Kasei Microdevices · AKD5365 is an evaluation board for the...

Documents

Transcript of AKD5365 English Manual - AKM - Asahi Kasei Microdevices · AKD5365 is an evaluation board for the...