AJP2019 - Faculdade de Engenharia da Universidade do Portoajp2019/AJP2019 Prog.pdf · N Günther...

AJP20191st International Conference on Advanced Joining Processes

Programme

24-25 OCTOBER 2019

PONTA DELGADA, AZORES

SUPPORT

1ST INTERNATIONAL CONFERENCE ON ADVANCED JOINING PROCESSES 2

PROGRAMME OF AJP2019

Author underlined presenting author

Thursday 24 October 2019

8:40 AJP 2019 Opening (Room Hortência)

Session 1A – Joining by forming I

(Chair: P Martins and E Tekkaya)

Session 1B – Laser welding I

(Chair: K Dilger and A Astarita)

Session 1C – Adhesive bonding I

(Chair: JC Del Real and JA Poulis)

Room Hortência Room Protea Room Azálea

9:00 Deformation assisted joining (AJP19_1)

N Bay (Technical University of Denmark, Denmark), LM Alves, CV Nielsen, CMA Silva, PAF Martins

Laser-based additive manufacturing of optical, thermal and structural components (AJP19_20)

P Neef (Clausthal University of Technology, Germany), R Bernhard, H Wiche, V Wesling

Characterization of industrial adhesives in terms of fatigue crack growth and impact strength (AJP19_6)

A Akhavan-Safar (INEGI, Portugal), EAS Marques, R Carbas, LFM da Silva, M El-Zein, N Carrere, I Maus, Y Takahashi, J Sherwood

9:20 Experimental analysis of laser beam welding of zinc coated sheets with zero gap (AJP19_21)

A Franz (Volkswagen AG, Germany), D Paethe, K Dilger

Extending the service life of the functional properties of the surface of cement composites using nanoparticles as preventive repair (AJP19_7)

J Szymanowski (Wrocław University of Science and Technology, Poland)

9:40 Stress state dependent damage modelling of self-pierce riveting process simulation using GISSMO damage model (AJP19_27)

M Otroshi (Paderborn University, Germany), M Rossel, G Meschut

Research on the protective capability of the laser welded armour steel plates (AJP19_26)

D Pacek (Military Institute of Armament Technology, Poland), P Kolodziejczak, K Grzelak, J Torzewski, P Podgorzak

Structural bonding of single layer e-coated steel structures in the agricultural sector (AJP19_81)

D Estephan, S Boehm (University of Kassel, Germany), R Nothhelfer-Richter

10:00 Influence of the mechanical properties of the joining partners on the load bearing capacity of shear-clinched joints (AJP19_28)

S Wiesenmayer (Friedrich-Alexander-Universität Erlangen-Nurnberg, Germany), M Graser, M Merklein

Laser-based surface pretreatment for metal-plastic hybrids using a new process strategy (AJP19_44)

C Wunderling (Technical University of Munich, Germany), L Mayr, SP Meyer, MF Zaeh

Methodology of controlling the process of technology of construction of floors made of cement-based materials (AJP19_30)

Ł Sadowski (Wrocław University of Science and Technology, Poland), A Hoła, J Hoła

10:20 Influence of the process temperature on the tribological behaviour during bulk forming of high nitrogen steel (AJP19_32)

C Kuball (Friedrich-Alexander-Universität Erlangen-Nurnberg, Germany), R Jung, B Uhe, G Meschut, M Merklein

Process studies on copper laser beam welding over gap by using disc laser at green wavelength (AJP19_45)

W-S Chung (Fraunhofer Institute for Laser Technology ILT, Germany), A Olowinsky, A Gillner

The development of a low-cost thermoplastic fibre metal laminate for impact applications (AJP19_33)

JA Poulis (Delft University of Technology, The Netherlands), K Simoiu, DI Gransden

10:40-11:00 COFFEE BREAK

Session 2A – Advanced welding processes I

(Chair: A Reguly and R Carbas)

Session 2B – Adhesive bonding II

(Chair: R Goyal and E Marques)

Session 2C – Joining by forming II

(Chair: N Bay and M Merklein)


11:00 High powered ultrasonic devices for welding applications with plastics (AJP19_4)

RD Adams (Universities of Oxford and Bristol, UK)

Research on the mechanical characterization and numerical modelling of the behaviour of structural adhesives under impact loads for automotive applications (AJP19_12)

EAS Marques (INEGI, Portugal), CSP Borges, PDP Nunes, A Akhavan, RJC Carbas, LFM da Silva

Single stage joining by forming process for fixing sheets to tubes (AJP19_9)

LM Alves, RM Afonso (University of Lisbon, Portugal), FLR Silva, PAF Martins

11:20 Effect of thermal cycles on microstructure and mechanical properties of Mg/Al/Ti multi-layer material (AJP19_16)

M Wachowski (Military University of Technology, Poland), R Kosturek, L Śnieżek, I Szachogłuchowicz, T. Barciński, K Grzelak

Mechanical characterization and numerical modelling of the high strain rate behaviour of structural adhesives under mixed mode loadings (AJP19_162)

PDP Nunes (INEGI, Portugal), CSP Borges, EAS Marques, A Akhavan, RJC Carbas, LFM da Silva

Joining by forming of copper and aluminium alloys for electrical applications (AJP19_37)

U Fussel (TU Dresden, Germany), J Kalich

31ST INTERNATIONAL CONFERENCE ON ADVANCED JOINING PROCESSES

11:40 Process monitoring of ultrasonic metal welding of battery tabs using external sensor data (AJP19_25)

I Balz (RWTH Aachen University, Germany), U Reisgen, A Schiebahn, E Abi Raad, M. Vorländer

Deformation measurement within adhesive bonds of aluminum and CFRP using advanced fiber optic sensors (AJP19_42)

H Grefe (Technische Universität Braunschweig, Germany), K Dilger

Joining dissimilar thin-walled tubes by magnetic pulse welding (AJP19_38)

J Lueg-Althoff (TU Dortmund University, Germany), J Bellmann, M Hahn, S Schulze, AE Tekkaya, E Beyer

12:00 Projection welding reinvented (AJP19_29)

H-J Rusch (Joining process development Institute, Germany), N Stocks, A Maisuradze, U. Fussel, J Zschetzsche

Structural adhesive bonding of high performance thermoplastics (PEEK) (AJP19_49)

E Arikan (Bundeswehr Research Institute for Materials, Fuels and Lubricants (WIWeB), Germany), J Holtmannspötter, HJ Gudladt

Potential of joining dissimilar materials by cold formed pin-structures (AJP19_40)

M Kraus (Friedrich-Alexander-Universität Erlangen-Nurnberg (FAU), Germany), M Merklein

12:20 Non-destructive quality assurance of magnetic pulse welded dissimilar sheet joints of aluminum and steel by means of active thermography (AJP19_35)

E Schumacher (University of Kassel, Germany), E Prints, I Kryukov, M Graß, S Boehm

Design concept for adhesively bonded steel/CFRP structures under cyclic loading (AJP19_54)

J Kowatz (Paderborn University, Germany), G Meschut

Joining by die-less hydroforming with outer pressurization (AJP19_41)

F Weber (Insitute of Forming Technology and Lightweight Components, Germany), M Hahn, AE Tekkaya

12:40 Adaption of a topographical measurement system for beam welding processes with high temporal and spatial resolution (AJP19_52)

U Reisgen, S Jakobs (RWTH Aachen University, Germany), M Sawannia

The effect of surface roughness in a μm- and sub-μm-scale on the adhesion of thermoset polymers (AJP19_108)

F Zimmer (WIWeB, Germany), J Holtmannspötter, T Hofmann, H-J Gudladt

Joining by boss forming of tubes and rods to sheets (AJP19_164)

RM Afonso (Universidade de Lisboa, Portugal), LM Alves, PAF Martins

13:00-14:00 LUNCH BREAK

Session 3A – Friction stir welding I

(Chair: P Moreira and K Schricker)

Session 3B – Adhesive bonding III

(Chair: RD Adams and R Carbas)

Session 3C – Computational models

(Chair: M El-Zein and J Goldak)


14:00 Towards a process-property model for linear friction welding of Ni-based superalloy (AJP19_140)

SI Okeke (National University of Ireland Galway, Ireland), N Harrison, M Tong

Strength of laminates aluminium carbon-fibre joints under impact loads (AJP19_14)

RJC Carbas (INEGI, Portugal), MAMS Pereira, EAS Marques, LFM da Silva

From computational mechanics to optimal design (AJP19_17)

J Goldak (Carleton University, Canada)

14:20 Towards friction welding to API grade B pipes (AJP19_59)

DT Buzzatti, JT Buzzatti, GVB Lemos, CV Amavisca, DLP Oliveira, F Mattei, G Dalpiaz, A Reguly (Universidade Federal do Rio Grande do Sul, Brazil)

Influence of adhesives’ morphology on bonding strength (AJP19_56)

N Merlinge, B Hassoune-Rhabbour, T Mérian, A Visse, V Nassiet (ENIT, France)

Correlating large sets of experimental data with high resolution computational weld mechanics models (AJP19_18)

J Goldak (Carleton University, Canada), M Martinez, X Huang, D Aidun

14:40 Friction weldability of ultra-fine grained titanium (AJP19_39)

B Skowrońska, T Chmielewski (Warsaw University of Technology, Poland), W Pachla, J Skiba, M Kulczyk, D Golański

Investigation of the loading capacity of adhesive joints in multi-material structures regarding their manufacturing process (AJP19_57)

N Gunther (Technische Universität Braunschweig, Germany), M Griese, E Stammen, K Dilger

Novel model for mean stress effect on high-cycle fatigue performance of threaded fasteners (AJP19_120)

T Li, SA Nassar (Oakland University, USA), M El-Zein

15:00 In situ monitoring of friction stir spot welded EN AW 1050/EN CW 004A lap joints using artificial neural nets (AJP19_51)

T Koehler, M Schiele, M Glaser, K Schricker (Technische Universität Ilmenau, Germany), JP Bergmann, K Augsburg

Performance increase in continuous casting of steel using adhesive bonding (AJP19_64)

P Jousset (University of Applied Sciences HSR, Switzerland), C Corbisieri, D Stapf, O Mathews, S Feldhaus, GA Barandun

Machine learning models applied to FSW defect index using multiple joint configurations and alloys (AJP19_90)

F Nadeau (National Research Council Canada – Aluminium Technology Centre, Canada,), B Thériault, M-O Gagné

15:20 System design and development of friction stir welding of polymers (AJP19_60)

S Eslami (INEGI, Portugal), PJ Tavares, PMGP Moreira

ECT for bonding - Challenges for the use of electrical capacitance tomography in bonding technology (AJP19_72)

ST Voß (Fraunhofer IFAM, Germany), H Fricke, B Mayer

Development of semi-analytical models for aircraft wheel assembly design (AJP19_103)

A Haddar (Université de Toulouse, France), L Augustins, A Daidie, E Rodriguez


15:40 Reduction of FSW-system loadability, process force and weld seam width by tool scaling (AJP19_63)

M Grätze (Technische Universität Ilmenau, Germany), M Hasieber, T Löhn, JP Bergmann

Durability estimation of adhesively bonded joints in water with accelerated degradation tests (AJP19_79)

K Shimamoto (National Institute of Advanced Industrial Science and Technology, Japan), S Batorova, H Akiyama, C Sato

Experimentally-validated welding and constitutive modelling of 9Cr steel (AJP19_87)

P Mac Ardghail (National University of Ireland Galway, Ireland), N Harrison, SA Alexandratos, ED Meade, I Sabirov, J Llorca, NP O’Dowd, SB Leen


Session 4A – Adhesive bonding IV

(Chair: S Nassar and J Holtmannspötter)

Session 4B – Laser welding II

(Chair: U Reisgen and FJG Silva)

Session 4C – Joining by forming III

(Chair: M Bambach and A de Jesus)


16:20 Characterization of magnetic cork particles to manufacture composite materials or to modify adhesives (AJP19_82)

J Abenojar (Universidad Carlos III de Madrid, Spain), S Lopez de Armentia, P Gálvez, AQ Barbosa, LFM da Silva, MA Martinez

Mechanical characterization of PEKK transmission laser welding joints using a modified driven wedge test (AJP19_46)

C Garnier (Université de Toulouse, France), F Chabert, M Villar Montoya, V Nassiet

Joining overlapped sheets by sheet bulk metal forming (AJP19_71)

JPM Pragana (Universidade de Lisboa, Portugal), RJS Baptista, IMF Bragança, CMA Silva, LM Alves, PAF Martins

16:40 Brittle epoxy reinforced with micro particles of magnetized cork: effect of size and amount (AJP19_10)

AQ Barbosa (INEGI, Portugal), JB Marques, LFM da Silva, R Carbas, C Silva, J Abenojar, MA Martinez

Transmission laser welding of polyamides: effect of process parameters on the material properties and interfacial strength (AJP19_48)

F Chabert (Université de Toulouse, France), C Garnier, J Sangleboeuf, AC Akue Asseko, B Cosson

Mechanical joining of dissimilar metallic and non-metallic materials by a new one-side riveting process (AJP19_91)

C Kraus (Fraunhofer Institute for Machine Tools and Forming Technology, Germany), R Mauermann, W-G Drossel

17:00 Fiber-oriented joints of fibre reinforced plastics for a more efficient load transfer (AJP19_93)

J Holtmannspötter (WIWeB, Germany), M Niedernhuber, I Ehrlich

New approaches on laser micro welding of copper by using a laser beam source with a wavelength of 450 nm (AJP19_58)

M Hummel (RWTH Aachen University, Germany), C Schöler, A Häusler, A Gillner, R Poprawe

Novel fast simulation approach for mechanical joining processes (AJP19_142)

A Brosius, C Steinfelder (TU Dresden, Germany)

17:20 Advanced analytics of elastic adhesive bonds by means of in-situ computed tomography (AJP19_97)

J Philipp (Technische Universität Braunschweig, Germany), E Stammen, K Dilger

Use of pure vanadium and niobium/copper inserts for laser welding of titanium to stainless steel (AJP19_98)

A Mannucci (Université de Bourgogne-Franche Comté, France), I Tomashchuk, A Mathieu, R Bolot, E Cicala, S Lafaye, C Roudeix

Numerical study on manufacturing applicability of contact stress optimized shaft-hub connections joined by lateral extrusion (AJP19_119)

R Meissner (Institute for Metal Forming Technology, Germany), M Liewald, D Ulrich, H Binz

17:40 Measuring real-time ageing of adhesive bonds as a result of environmental factors (AJP19_105)

S Fevery (KU Leuven, Belgium), H Hallez, D Vandepitte, S Debruyne

Development and exploitation of local vacuum power beam welding for heavy section fabrication (AJP19_150)

C Punshon (TWI, UK)

Joining of metal-composite structures combining additive manufacturing and metal forming (AJP19_70)

RJS Baptista, JPM Pragana, IMF Bragança, CMA Silva (Universidade de Lisboa, Portugal), LM Alves, PAF Martins

18:00 Modelling the curing behavior of a toughened hot curing epoxide adhesive during paint drying process (AJP19_106)

M Griese (Technische Universität Braunschweig, Germany), N Gunther, E Stammen, K Dilger

Bonding mechanisms in laser-assisted joining of metal-polymer composites (AJP19_77)

K Schricker (Technische Universität Ilmenau, Germany), L Samfaß, M Grätzel, JP Bergmann

Fundamental analysis of the application of hybrid semi-finished products in sheet-bulk metal forming (AJP19_133)

R Schulte (Friedrich-Alexander-Universität Erlangen-Nurnberg, Germany), M Lechner, M Merklein

19:00 Poster session and RECEPTION

Laser welding

Poster 1 Effects of reduced ambient pressure and beam oscillation on gap bridging ability during solid state laser beam welding (AJP19_43)

M Köhler, T Toth, J Hensel (Technische Universität Braunschweig, Germany), K Dilger

Poster 2 Investigation of the interaction between laser beam welding processes and shielding gas supply (AJP19_78)

K Schricker (Technische Universität Ilmenau, Germany), A Baumann, JP Bergmann

Poster 3 Vapour plume and melted zone behavior during dissimilar laser welding of titanium to aluminum Alloy (AJP19_99)

M Raja Kumar, JM Jouvard (Université de Bourgogne-Franche Comté, France), I Tomashchuk, P Sallamand

Poster 4 Production of individual structures from silicate materials using Wire-Laser Additive Manufacturing (AJP19_155)

F Fröhlich (Technische Universität Ilmenau, Germany), J Hildebrand, JP Bergmann


Friction stir welding

Poster 5 Residual stress in friction welded API X65 pipes (AJP19_132)

CAP de Moraes, M Chludzinski, RM Nunes, GVB Lemos (Universidade Federal do Rio Grande do Sul (UFRGS, Brazil), A Reguly

Poster 6 Friction stir welding of coated aluminum alloys (AJP19_160)

U Reisgen, A Schiebahn, A Pipinikas (RWTH Aachen University, Aachen, Germany)

Poster 7 Additive joining of Al 5059 alloy plates using a novel route of friction stir additive manufacturing (AJP19_117)

M Srivastava (Manav Rachna International Institute of Research & Studies, India), S Rathee

Poster 8 Friction stir welding of Al5059 alloy: An investigation on the effect of SiC nano-particles addition during multiple passes (AJP19_116)

S Rathee (Amity University Madhya Pradesh, India), M Srivastava

Advanced welding processes

Poster 9 Influence of the interlayer on explosive welding of aluminium to carbon steel and aluminium to stainless steel (AJP19_86)

GHSFL Carvalho, I Galvão (University of Coimbra, Portugal), R Mendes, RM Leal, A Loureiro

Poster 10 Improving the mechanical strength of ductile cast iron welded joints using different heat-treatments (AJP19_129)

E Marques, FJG Silva (ISEP, Portugal), OC Paiva, AB Pereira

Poster 11 WAAM - Component properties for the scaling of the structure widths using GMAW process (AJP19_141)

J Reimann, A Rauch, P Henckell, Y Ali, J Hildebrand (Technische Universität Ilmenau, Germany), JP Bergmann

Poster 12 Evaluation of welded joints of structural steels using buttering welding technique (AJP19_144)

AA Ferreira (University of Porto, Portugal), MF Vieira, J Cruz

Poster 13 The use of Ni/Al nanolayers in the diffusion bonding of Ti6Al4V to Al

2O

3 (AJP19_145)

MN Silva (University of Porto, Portugal), AS Ramos, F Viana, MT Vieira, MF Vieira, S Simões

Poster 14 Brazing alumina to Ti6Al4V and g-TiAl alloys using Ag-Cu sputtered coated Ti filler foil (AJP19_146)

O Emadinia (University of Porto, Portugal), S Simões, CJ Tavares, A Guedes

Poster 15 Issues and challenges in component welding of high-strength fine-grained structural steels (AJP19_149)

T Kannengiesser (Bundesanstalt fur Materialforschung und -prufung (BAM), Germany), A Kromm, D Schroepfer

Poster 16 Research on microstructure and mechanical properties of explosively welded stainless steel/commercially pure Ti plate (AJP19_154)

M Wachowski, M Małek (Military University of Technology, Poland), R Kosturek, L Śnieżek, T Płociński

Computational models

Poster 17 Designing steel structures with multi-pass welds (AJP19_19)

J Goldak (Carleton University, Canada)

Poster 18 Experimental and numerical investigation of load bearing behavior of butt welds with steel grade S460, S690 and S700 depend on weld preparation (AJP19_139)

S Rasche (Technische Universität Ilmenau, Germany), S Hammer, J Hildebrand, J Spiegler, U Muckenheim, JP Bergmann, U Kuhlmann, S Keitel

Poster 19 Fast evaluation of friction stir welding based on a CFD-model of the process (AJP19_143)

U Reisgen, A Schiebahn, R Sharma, A Maslennikov (RWTH Aachen University, Germany), P Rabe, V Erofeev

Poster 20 A new precision FEM model of laser transmission welding PC by dynamically setting thermal contact resistance (AJP19_152)

CY Wang, C Wang (Soochow University, China), ZX Xia, HH Liu, Y Hao, CD Wang, ZL Chen

Poster 21 Modeling three-dimensional rough surface and simulation of temperature and flow field in laser transmission welding (AJP19_153)

CY Wang, MH Jiang (Soochow University, China), CD Wang, HH Liu, D Zhao, ZL Chen

Adhesive bonding

Poster 22 The effect of the addition of tin oxide nanoparticles on the level of adhesion between a modified overlay and the concrete substrate (AJP19_8)

J Szymanowski (Wrocław University of Science and Technology, Poland), Ł Sadowski

Poster 23 Thermal, rheological and mechanical characterization of an epoxy resin to be used as matrix in modified adhesives (AJP19_83)

J Abenojar (Universidad Carlos III de Madrid, Spain), AQ Barbosa, E Paz, MA Martinez, LFM da Silva


Poster 24 Challenges on the manufacture of functionally graded joints (AJP19_11)

AQ Barbosa (INEGI, Portugal), JB Marques, R Carbas, C Silva, LFM da Silva

Poster 25 Numerical modelling of multi-material functionally graded joints under shear loading (AJP19_15)

MQ dos Reis, RJC Carbas (INEGI, Portugal), EAS Marques, LFM da Silva

Poster 26 Resistance of long adhesive joints in façade applications exposed to negative pressure loads (AJP19_23)

B Nečasova (Brno University of Technology, Czech Republic), P Liška, J Šlanhof, P Sedlák, V Motyčka

Poster 27 Impact of technological indiscipline on failure rate of adhesive joints (AJP19_24)

P Liška (Brno University of Technology, Czech Republic), B Nečasová, J Šlanhof, P Schmid, V Motyčka

Poster 28 Comparative study of PUR-based reactive hot melts adhesive joints (AJP19_95)

MA Martinez (Universidad Carlos III de Madrid, Spain), J Abenojar, S Lopez de Armentia, JL Marulanda

Poster 29 Experimental and cohesive zone modelling study on joining of sheet moulding compound and carbon-epoxy composites (AJP19_136)

VHP Lopes, RDSG Campilho (Instituto Politécnico do Porto, Portugal), PJRO Nóvoa, RF Pinto

Poster 30 Experimental and numerical analysis of dual-adhesive stepped-lap aluminium joints (AJP19_137)

CL Ferreira, RDSG Campilho (Instituto Politécnico do Porto, Portugal), RDF Moreira

Poster 31 Effect of the curing temperature on the properties of epoxy adhesives at high temperatures (AJP19_147)

P Lozano, P Ayala, JC del Real, Y Ballesteros (Universidad Pontificia Comillas, Spain)

Poster 32 Non-destructive evaluation of adhesive joints using acoustic methods (AJP19_148)

J Rodriguez-Montes, Y Ballesteros-Iglesias, L Molisan, JC del Real (Universidad Pontificia Comillas, Spain)

Poster 33 Individualized and controlled laser beam pre-treatment process for adhesive bonding of fiber-reinforced plastics - Part I: Optical Detection of impurities on the component (AJP19_159)

J Weiland, B Kunze, H Dittmar, B Marx, A Schiebahn (RWTH Aachen University, Germany), P Jäschke, L Overmeyer, U Reisgen

Hybrid joining

Poster 34 Cyclic corrosion performance of carbon fiber reinforced composite-to-aluminum double lap joints with various joining methods (AJP19_124)

C Yang, M Gerini Romagnoli, G Belingardi, M El-Zein, SA Nassar (Oakland University, USA)

Poster 35 Tandem laser-GMAW joining of 20 mm thick superduplex stainless steel: An experimental and numerical study (AJP19_138)

A Mathieu, I Tkachenko, JM Jouvard (Université de Bourgogne-Franche Comté, France), I Tomashchuk

Poster 36 Innovative joining technology for the production of hybrid components from FRP and metals (AJP19_157)

U Reisgen, A Schiebahn, J Lotte (RWTH Aachen University, Germany)

Poster 37 Influence of the arrangement of mechanical fasteners on static strength and fatigue life of hybrid joints (AJP19_158)

J Godzimirski, M Rośkowicz (Military University of Technology, Poland), A Komorek, J Gąsior


Friday 25 October 2019

Session 5A – Advanced welding processes II

(Chair: F Nadeau and D Golanski)

Session 5B – Adhesive bonding V

(Chair: L Goglio and V Nassiet)

Room Hortência Room Protea

8:40 Reactive Ni-Al particles as an innovative heat source for microwave-assisted joining (AJP19_62)

S Grohmann (Technical University of Munich, Germany), G Langhans, A Reindl, V Sidarava, MF Zaeh

Evaluation of adhesion properties of lignin-epoxy adhesives in structural wood applications for automotive components (AJP19_161)

A Aniol (Volkswagen Group Innovation, Germany.), T Grosse, F Fischer, S Böhm

9:00 Ultrasonic welding of additively manufactured polyamide 12 components (AJP19_65)

S Popović (University of Applied Sciences HSR, Switzerland), P Schiesser, M Mazenauer, P Jousset

Effect of cure cycles and different stress combinations on an epoxy-based adhesive used in automotive applications (AJP19_118)

R Ciardiello, L Goglio (Politecnico di Torino, Italy), G Belingardi, L Greco, F Di Sciullo

9:20 Induction welding of polyethylene pipes (AJP19_66)

S Rutzer (University of Applied Sciences HSR, Switzerland), N Lipp, L Grab, D Petry, S Schöller, O Trefz, P Jousset

Effect of electromagnetic-susceptible additives on the reversibility of hot-melt adhesives (AJP19_121)

M Attanasio, M Gerini Romagnoli, G Belingardi, L Goglio, SA Nassar (Oakland University, USA)

9:40 Weldability of S700MC steel welded with the hybrid Plasma+MAG method (AJP19_67)

B Skowronska, T Chmielewski, D Golanski (Warsaw University of Technology, Poland), J Szulc

Mixed mode fracture energy measurement of adhesives using SCB specimen (AJP19_5)

A Akhavan-Safar (INEGI, Portugal), A Ajdani, MR Ayatollahi, LFM da Silva

10:00 Accelerated degradation of metal-plastic assemblies and single lap joints using pressure vessels (AJP19_69)

M Funabashi (National Institute of Advanced Industrial Science and Technology (AIST), Japan), T Shimada, F Ninomiya, T Fukata, H Akiyama

Mechanoluminescent study of mechanical event on adhesive joint for evaluation and design (AJP19_130)

N Terasaki (National Institute of Advanced Industrial Science and Technology (AIST), Japan), S Horiuchi, H Hkiyama, M Itabashi

10:20 Effect of physical simulated multipass welding thermal cycles on notch toughness of a 9% Ni steel (AJP19_156)

JC Soeiro Jr, P Vilaça, SD Brandi (University of Sao Paulo, Brazil)

Mechanical characterization and numerical modelling of the high strain rate behaviour of structural adhesives under mixed mode loadings (AJP19_13)

EAS Marques (INEGI, Portugal), CSP Borges, PDP Nunes, A Akhavan, RJC Carbas, LFM da Silva


Session 6A – Friction stir welding II

(Chair: H Fricke and S Smith)

Session 6B – Laser welding III

(Chair: R Goyal and A Gillner)


11:00 Prediction of the surface quality of friction stir welds by the analysis of process responses using Artificial neural networks (AJP19_75)

R Hartl (Technical University of Munich, Germany), B Praehofer, MF Zaeh

On the influence of in situ sound wave superposition on the microstructure of laser welded 7000 aluminum alloys (AJP19_80)

S Völkers (University of Kassel, Germany), E Scharifi, S Sajjadifar, S Böhm, U Weidig, T Niendorf

11:20 Approaches for manufacturing current-carrying dissimilar multi-sheet welds from pure aluminum and copper thin sheets materials using friction stir welding (AJP19_107)

A Tchouaha Tankoua (Daimler AG, Germany), P Betz, JP Bergmann

Interactions of the process parameters and mechanical properties of laser butt welds in thin HSLA steel plates (AJP19_89)

P Riofrío (University of Coimbra, Portugal), C Capela, JAM Ferreira, AL Ramalho

11:40 Effect of friction stir processing on microstructural, mechanical and corrosion properties of Al-Si12 additive manufactured components (AJP19_110)

G Moeini, SV Sajadifar, T Engler, B Heider, T Niendorf, M Oechsner, S Böhm (University of Kassel, Germany)

Investigation of the ageing behaviour of laser-joined plastic-metal hybrid compounds (AJP19_92)

K van der Straeten (Fraunhofer Institute for Laser Technology ILT, Germany), S Quach, A Olowinsky, A Gillner


12:00 Similar and dissimilar linear friction welding of additive manufactured Ti6Al4V parts (AJP19_114)

A Astarita (University of Naples “Federico II”, Italy), AT Silvestri, G Scelzo, F Scherillo, S Franchitti, A Squillace

Investigations on the influence of beam shaping in laser transmission welding of multi-layer polymer films with wavelength-adapted diode laser beam sources (AJP19_96)

M Brosda (Fraunhofer Institute for Laser Technology ILT, Germany), P Nguyen, A Olowinsky, A Gillner

12:20 Hydrogen embrittlement under cathodic protection of friction stir welded UNS S32760 super duplex stainless steel (AJP19_135)

CEF Kwietniewski (UFRGS, Brazil), CP Meinhardt, A Scheid, T Renck

Processing of keyhole depth measurement data during laser beam micro welding (AJP19_115)

S Hollatz (Fraunhofer Institute for Laser Technology ILT, Germany), M Hummel, L Jaklen, A Olowinsky, A Gillner

12:40 Friction stir weld-bonded joints under impact loading (AJP19_163)

DFO Braga, AVL Gregorio, S Pourhassan, PAR Rosa, PMGP Moreira (INEGI, Portugal), LFM da Silva, V Infante

Laser welding of thin austenitic steel structure: an experimental and numerical study (AJP19_126)

H Aberbache (Université de Bourgogne-Franche Comté, France), A Mathieu, R Bolot, L Bleurvacq, A Corolleur, F Laurent

13:00-14:00 LUNCH BREAK

Session 7A – Hybrid joining I

(Chair: S Böhm and U Reisgen)

Session 7B – Fatigue of joints

(Chair: J Goldak and H Remes)


14:00 Investigation on clinching with additional local material bond by thermal joining (AJP19_1)

V Wesling, H Wiche, C Koch (Clausthal University of Technology, Germany)

Impact of the drilling process on the fatigue life of an aluminium 2024-T351 part (AJP19_109)

A Lacombe (Université de Toulouse, France), Y Landon, M Paredes, C Chirol, A Benaben

14:20 Battery pack manufacturing – a redefinition of requirements for joining technologies (AJP19_31)

MFR Zwicker (Technical University of Denmark, Denmark), M Moghadam, W Zhang, CV Nielsen

Multiaxial fatigue strength assessment of welded steel joints using 3D finite element analyses according to the peak stress method (AJP19_74)

G Meneghetti (University of Padova, Italy), A Campagnolo

14:40 Process behavior of spot weld bonded three-sheet steel stack-ups and analysis strategies with on-line measuring methods (AJP19_3)

S Brechelt, P Neef (Clausthal University of Technology, Germany), H Wiche, V Wesling

Influence of laser weld shape on mechanical and fatigue behaviour of single lap laser welded joints (AJP19_22)

R Goyal (Deere & Company, India), M El-zein

15:00 Hybrid manufacturing of components from Ti-6A-4V by metal forming and wire-arc additive manufacturing (AJP19_50)

M Bambach (Brandenburg University of Technology Cottbus-Senftenberg, Germany), I Sizova, B Sydow, M Gunther, S Hemes, F Meiners

Influence of thermal cycles on the welding of Grade 91 steel (AJP19_128)

AP Pinho, FJG Silva (ISEP, Portugal), OC Paiva, AB Pereira

15:20 Simulation and rheology: The key to understand hybrid bonding processes (AJP19_73)

H Fricke (Fraunhofer IFAM, Germany), S Voss

A strain–based fatigue life modelling of high-performing welded joints (AJP19_122)

H Remes (Aalto University, Finland), P Lehto, P Gallo, J Romanoff

15:40 New understanding of resistance spot welding for dissimilar joining of steel to aluminium (AJP19_101)

A Oliveira (TWI, UK), S Smith, HB Nadendla

Fatigue performance of double shear bolted splices for rack structures (AJP19_127)

AMP de Jesus (University of Porto, Portugal), VMG Gomes, G Lesiuk, JAFO Correia, MAV Figueiredo, AA Fernandes


Session 8A – Advanced welding processes III

(Chair: G Meneghetti and A Loureiro)

Session 8B – Hybrid joining II

(Chair: C Nielsen and E Marques)


16:20 Investigation of a new process for the additive manufacturing of graded metallic structures by in-situ alloying (AJP19_84)

F Akyel (RWTH Aachen University, Germany), S Olschok, U Reisgen

Modeling of multi-material hybrid joints under high rate loading (AJP19_53)

N Ledford (Fraunhofer Institute for High-Speed Dynamics, Germany), M May


16:40 Aluminium-copper explosive welding: A global weldability analysis (AJP19_85)

GHSFL Carvalho, I Galvão (University of Coimbra, Portugal), R Mendes, RM Leal, A Loureiro

Hybrid rivet-bonded joining of aluminum substrates: effect of joining technique and adherend thickness (AJP19_88)

VC Beber, M Baumert, B Schneider (Fraunhofer IFAM, Germany), A Wulf, C Nagel, M Brede

17:00 Evaluation of the properties of plastic-metal interfaces directly bonded via injection molding (AJP19_94)

S Horiuchi (Research Laboratory for Adhesion and Interfacial Phenomena, Japan), N Terasaki, M Itabashi

Comparative review of processes for the joining of steel to aluminium in car body applications (AJP19_100)

A Oliveira (TWI, UK), S Smith, HB Nadendla

17:20 Welding process for the additive manufacturing of cantilevered components with the WAAM (AJP19_102)

T Feucht (Technische Universität Darmstadt, Germany), J Lange

Dissimilar metal joining of aluminum to steel by hybrid process of adhesive bonding and projection welding using a novel insert element (AJP19_104)

A Zvorykina (Otto von Guericke University, Germany), M Neubauer, O Sherepenko, S Juttner

17:40 Single-sided resistance spot welding of steel-aluminum dissimilar joints - mechanical characterization and interface formation (AJP19_111)

K Szallies (Technische Universität Ilmenau, Germany), M Bielenin, JP Bergmann

Solid state joining of metals with vaporizing foil actuator welding (AJP19_123)

BJ Ufferman (The Ohio State University, USA), Y Mao, A Vivek, G Daehn

18:00 Connected, digitalized welding production – Utilizing process and nondestructive testing data for improved quality control (AJP19_113)

U Reisgen, R Sharma, S Mann (RWTH Aachen University, Germany)

Industrialization of the hybrid metal extrusion and bonding process (HYB) (AJP19_125)

F Leoni (Norwegian University of Science and Technology, Norway), L Sandnes, Ø Grong, F Berto

20:00 AJP2019 BANQUET AT ARQUIPÉLAGO

AJP2019 - Faculdade de Engenharia da Universidade do Portoajp2019/AJP2019 Prog.pdf · N Günther...

Documents

Transcript of AJP2019 - Faculdade de Engenharia da Universidade do Portoajp2019/AJP2019 Prog.pdf · N Günther...