AIRCOM® PLUS CharacteristicsDiameter 10,3 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 13,4 dBAttenuation @ 1 GHz/100ft 4,08 dB f 10 GHzmax

AIRCELL® 7 CharacteristicsDiameter 7,3 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 21,52 dBAttenuation @ 1 GHz/100ft 4,08 dB f 6 GHzmax

ECOFLEX® 10 CharacteristicsDiameter 10,2 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 14,2 dBAttenuation @ 1 GHz/100ft 4,33 dB f 6 GHzmax

ECOFLEX® 15 CharacteristicsDiameter 14,6 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 9,8 dBAttenuation @ 1 GHz/100ft 2,99 dB f 6 GHzmax

Cut your losses...

...with low loss coaxial cables

Over the past several years, there has been an increased demand for low losscoaxial cables due to the intensive utilization of frequency spectrum well up intothe microwave regions.All the cables that are presented in this brochure meet these requirements at avery competitive price.

AIRCOM® PLUS with its unique air cell dielectric has become one of the mostpopular multi-purpose coaxial cables since its introduction in 1989. A speciallydesigned honeycomb expander maintains the correct position of the center con-ductor while keeping the cable impedance constant even when it’s sharply bent.This high quality, semi-air spaced cable can be used for applications up into the10 GHz microwave region. Throughout its useable frequency range AIRCOM PLUSachieves a remarkable low loss despite its small diameter of 10.3 mm (0.4inches)

AIRCELL®7 is an extremely flexible coaxial cable with a surprisingly low losseven though its diameter is just 7.3mm (approx. 0.28 inch). Because of its 19strand copper center conductor, a bending radius as small as 25 mm (approx. 1inch) is allowed. This makes AIRCELL®7 ideal for small to intermediate distancesor where limited space does not allow the use of larger diameter cables.

The ECOFLEX® family of coaxial cables is the number 1 choice when it comesto flexibility, low loss and ease of use. IP 68 compliant solderless N-connectorsare available, thus allowing the manufacture of cable assemblies in minutes.ECOFLEX® cables are the European wide industrial standard for general com-munications use. They are also ideally suited for use in the 2.4 GHz and 5 GHzWLAN bands.

Precise coaxial connectors are an absolute necessity for long lasting trouble freeconnections! For all the cables presented in this brochure, the most commontypes of coaxial connectors are available. These specially designed connectorsfeature:• extended housings • oversized gaskets for better sealing and above average strain relief • no special tooling requirements.Easy to read assembly instructions can be downloaded from the internet.For long lasting high-quality connections, we strongly recommend using thegenuine AIRCELL®7, AIRCOM® PLUS und ECOFLEX® coaxial connectors.

Low loss coaxial cable for radio communications

AIRCOM PLUS® is a semi air spaced coa-xial cable with excellent electric and mecha-nical properties. Its low-loss characteristicsmakes it very suitable for applications up into themicrowave range.

AIRCOM PLUS® features a unique PE-honeycomb ex-pander which retains the correct impedance even whensharply bent.

The expander provides a tight seal around the solid centerconductor which is made from oxygen free copper, thusensuring it is protected against moisture and corrosion.

Another feature of AIRCOM PLUS® is its double shieldingwhich is constructed of overlapping copperfoil plus an addi-tional tightly woven copperbraid resulting in a screeningefficiency > 85 dB@1 GHz.

The copperfoil has an applied PE-coating which preventsfoil cracking due to short radius bends and the black PVC-sheath of AIRCOM PLUS® is UV-stabilized.

AIRCOM PLUS® is the 1st choice when a low-loss micro-wave rated cable is required. It’s economical pricemakes it the clear leader for today’s demanding appli-cations.

AIRCOM PLUS® is available from stock in thefollowing standard drum sizes:

25m, 50m, 100m, 200m and 500m.

CharacteristicsDiameter 10,3 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 13,4 dBAttenuation @ 1 GHz/100ft 4,08 dB f 10 GHzmax

AIRCOM PLUS® Connectors

Art.-Nr. 7367 N-plug, male

Art.-Nr. 7360 N-right angle connector

Art.-Nr. 7364 N-plug, female

Art.-Nr. 7379 BNC-plug, male

Art.-Nr. 7382 TNC-plug, male

Art.-Nr. 7384 TNC-RP-plug, male (reverse polarity)

Art.-Nr. 7378 UHF-plug, male

Frequency (GHz)

-10 dB-15 dB-20 dB-25 dB-30 dB-35 dB-40 dB

0,0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0 8,5 9,0 9,5 10,0

-5 dB0 dB

Technical dataConstructionCentre conductor bare copper, oxygen free

1 x 2,7 mmCentre conductor Ø 2,7 mmDielectric semi airspaced PEDielectric Ø 7,2 mmOuter conductor 1 copperfoil, PE coatedShielding factor 100%Outer conductor 2 copper braid, 75%Sheath black PVC, uv-resistantOuter diameter Ø 10,3 mm

Mechanical specificationsWeight (100 m) 15 kgMin. bending radius 55 mmTemperature range - 40 .... + 80 °CPulling strength 5 daN

Electrical specificationsImpedance 50 OhmCapacity 81 pF/mVelocity factor 0,83f 10 GHzScreening efficiency @ 1 GHz > 85 dBDC-resistance

Centre conductor 3,1 Ohm/kmOuter conductor 6,4 Ohm/km

RF peak voltage 1 kV

Max. power handling (W @40°C)10 MHz 3980

100 MHz 1210500 MHz 510

1000 MHz 3402000 MHz 1803000 MHz 1504000 MHz 110

Typ. attenuation (dB/100m@20°C) dB/100ft @20°C5 MHz 0,9 0,27

10 MHz 1,2 0,37 50 MHz 2,6 0,79

100 MHz 3,8 1,16144 MHz 4,6 1,40200 MHz 5,5 1,68300 MHz 6,8 2,07432 MHz 8,4 2,56500 MHz 9,0 2,74800 MHz 11,8 3,60

1000 MHz 13,4 4,081296 MHz 15,6 4,761500 MHz 17,0 5,181800 MHz 18,9 5,762000 MHz 20,1 6,132400 MHz 22,5 6,863000 MHz 25,9 7,904000 MHz 31,1 9,485000 MHz 35,9 10,946000 MHz 40,6 12,38

10000 MHz 58,3 17,77

100 dB

10 dB

1dB

0,1 dB30 100 1000 10000

Frequency (MHz)

AccessoriesGrounding clamp Art.-Nr. 6085

Attenuation (dB/100 m) @ 20°C

Return loss

For your informationAIRCOM PLUS® RG 213/U RG 58/U

Capacity pF/m 81 101 102Velocity factor 0,83 0,66 0,66attenuation dB/100 m

10 MHz 1,2 2,0 5,0100 MHz 3,8 7,0 17,0500 MHz 9,0 17,0 39,0

1000 MHz 13,4 22,5 54,63000 MHz 25,9 58,5 118

max

AIRCOM PLUS® is a registered trademark of SSB-Electronic GmbH.

Due to production tolerances the RTL may have different characteristics

Low loss coaxial cable for radio communications

AIRCELL®7 is a super flexible coaxialcable designed for frequencies up to 6 GHz.At a diameter of just 7,3 mm ( (0.287” OD)and a minimum bending radius of just 25 mm,it offers relatively low loss.

The low attenuation of AIRCELL®7 is achievedthrough advanced manufacturing techniques and theuse of a PE-LLC dielectric with a foaming rate of morethan 70%.

The extreme flexibility of AIRCELL®7 is further enhancedthrough the use of a multi-stranded oxygen-free center con-ductor. Further advantages of this cable include the use ofdouble shielding which is constructed of overlapping copper-foil plus an additional tightly woven copperbraid. The copper-foil has an applied PE-coating which prevents foil cracking dueto short radius bends and the black PVC-sheath of AIRCELL®7is uv-stabilized.

A screening efficiency of > 85 dB@1GHz is realized.

AIRCELL®7 is the right choice, when a super flexible, micro-wave rated cable is required. Its economical price makes it theclear leader for today’s demanding application.

AIRCELL®7 is available from stock in the following standarddrum sizes:

25m, 50m, 100m, 200m and 500m

CharacteristicsDiameter 7,3 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 21,52 dBAttenuation @ 1 GHz/100ft 4,08 dB f 6 GHzmax

AIRCELL® 7 Connectors

Art.-Nr. 7392 N-plug, male

Art.-Nr. 7393 N-plug, female

Art.-Nr. 7399 N-right angle connector

Art.-Nr. 7391 BNC-plug, male

Art.-Nr. 7396 TNC-plug, male

Art.-Nr. 7390 UHF-plug, male standard

Art.-Nr. 7394 UHF-plug, male prof.

Frequency (GHz)

-10 dB-15 dB-20 dB-25 dB-30 dB-35 dB-40 dB

0,0 0,5 1,0 1,5 2,0 2,5 3,5 4,0 4,5 5,0 5,5 6,03,0

-5 dB0 dB

Technical data

100 dB

10 dB

1dB

0,1 dB30 100 1000 6000

Frequency (MHz)

Attenuation (dB/100 m) @ 20°C

Return loss

For your informationAIRCELL®7 RG 213/U RG 58/U

Capacity pF/m 75 101 102Velocity factor 0,83 0,66 0,66attenuation dB/100 m

10 MHz 2,2 2,0 5,0100 MHz 6,28 7,0 17,0500 MHz 14,72 17,0 39,0

1000 MHz 21,52 22,5 54,63000 MHz 40,88 58,5 118

max

AIRCELL is a registered trademark of SSB-Electronic GmbH.

Due to production tolerances the RTL may have different characteristics

ConstructionCentre conductor stranded copper, oxygen free

19 x 0,37 mmCentre conductor Ø 1,85 mmDielectric PE low loss compoundDielectric Ø 5,0 mmOuter conductor 1 copperfoil, PE coatedShielding factor 100%Outer conductor 2 copper braid, 70%Sheath black PVC, uv-resistantOuter diameter Ø 7,3 mm

Mechanical specificationsWeight (100 m) 7,2 kgMin. bending radius 25 mmTemperature range - 30 .... + 80 °CPulling strength 2 daN

Electrical specificationsImpedance 50 OhmCapacity 75 pF/mVelocity factor 0,83f 6 GHzScreening efficiency @ 1 GHz > 83 dBDC-resistance

Centre conductor 3,1 Ohm/kmOuter conductor 6,4 Ohm/km

RF peak voltage 1 kV

Max. power handling (W @40°C)10 MHz 2040

100 MHz 620500 MHz 260

1000 MHz 1802000 MHz 1203000 MHz 90

Typ. attenuation (dB/100m@20°C) dB/100ft @20°C5 MHz 1,6 0,49

10 MHz 2,2 0,6750 MHz 4,52 1,38

100 MHz 6,28 1,91144 MHz 7,6 2,32200 MHz 9,04 2,75300 MHz 11,2 3,41432 MHz 13,6 4,15500 MHz 14,72 4,49800 MHz 19,0 5,79

1000 MHz 21,52 6,561296 MHz 24,84 7,571500 MHz 27,08 8,261800 MHz 30,0 9,152000 MHz 31,88 9,722400 MHz 35,6 10,853000 MHz 40,88 12,464000 MHz 49,12 14,985000 MHz 57,04 17,396000 MHz 64,9 19,79

Low loss coaxial cable for radio communications

ECOFLEX 10 is a flexible, low-losscoaxial cable specifically designed foruse up to 6 GHz.

Advanced manufacturing techniques combinedwith the use of a low-loss PE-LLC Dielectric yieldsa foaming rate of more than 70%. This results invery low attenuation. ECOFLEX 10 sets a new stan-dard among flexible coaxial cables.

The flexibility of ECOFLEX 10 is further enhanced throughthe use of a stranded, oxygen-free copper center conductor.

Use of proprietary techniques, continuous center conductorcalibration and compression as well as the application of aprecoating results in low losses and good impedance match-ing.Further advantages of the cable include the use of doubleshielding which is constructed of overlapping copperfoil plusan additional tight woven copper braid. A screening efficiencyof > 90 dB@ 1 GHz is realized.The copperfoil has an applied PE-coating which prevents foilcracking due to short radius bends.The black PVC sheath of ECOFLEX 10 is uv-stabilized.

In addition to a full compliment of standard connectors, aneasy to use solder free N-connector has been speciallydeveloped for ECOFLEX 10. Connector installation only takesa few minutes and requires no special tools.

ECOFLEX 10 is the right choice when a low loss, highlyflexible microwave rated cable is required. It’s economi-cal price makes it the clear leader for today’s deman-ding applications.

ECOFLEX 10 is available from stock in thefollowing standard drum sizes:25m, 50m, 100m, 200m and 500m.

CharacteristicsDiameter 10,2 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 14,2 dBAttenuation @ 1 GHz/100ft 4,33 dB f 6 GHzmax

ECOFLEX® 10 Connectors

Art.-Nr. 7367 N-plug, male

Art.-Nr. 7383 N-plug, male, solderless

Art.-Nr. 7360 N-right angle connector

Art.-Nr. 7364 N-plug, female

Art.-Nr. 7379 BNC-plug, male

Art.-Nr. 7382 TNC-Stecker

Art.-Nr. 7384 TNC-RP-plug, male (reverse polarity)

Art.-Nr. 7378 UHF-plug, male

Frequency (GHz)

-10 dB-15 dB-20 dB-25 dB-30 dB-35 dB-40 dB

1,00,50,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0

-5 dB0 dB

Technical dataConstructionCentre conductor stranded copper, oxygen free

7 x 1,0 mmCentre conductor Ø 2,85 mmDielectric low loss compound PEDielectric Ø 7,25 mmOuter conductor 1 copperfoil, PE coatedShielding factor 100%Outer conductor 2 copper braid, 72%Sheath black PVC, uv-resistantOuter diameter Ø 10,2 mm

Mechanical specificationsWeight (100 m) 13,1 kgMin. bending radius 40 mmTemperature range - 40 .... + 85 °CPulling strength 5 daN

Electrical specificationsImpedance 50 OhmCapacity 78 pF/mVelocity factor 0,85f 6 GHzScreening efficiency @ 1 GHz > 90 dBDC-resistance

Centre conductor 3,3 Ohm/kmOuter conductor 8,4 Ohm/km

RF peak voltage 1 kV

Max. power handling (W @40°C)10 MHz 3960

100 MHz 1210500 MHz 510

1000 MHz 3502000 MHz 2303000 MHz 1804000 MHz 1505000 MHz 1306000 MHz 120

Typ. attenuation (dB/100m@20°C) dB/100ft @20°C5 MHz 0,8 0,24

10 MHz 1,2 0,37 50 MHz 2,8 0,85

100 MHz 4,0 1,22144 MHz 4,9 1,49200 MHz 5,8 1,77300 MHz 7,3 2,23432 MHz 8,9 2,71500 MHz 9,6 2,93800 MHz 12,5 3,81

1000 MHz 14,2 4,331296 MHz 16,5 5,031500 MHz 17,9 5,461800 MHz 19,9 6,072000 MHz 21,2 6,462400 MHz 23,6 7,203000 MHz 27,0 8,234000 MHz 32,2 9,825000 MHz 37,0 11,286000 MHz 41,5 12,65

100 dB

10 dB

1dB

0,1 dB30 100 1000 6000

Frequency (MHz)

AccessoriesGrounding clamp Art.-Nr. 6085

Attenuation (dB/100 m) @ 20°C

Return loss

For your informationECOFLEX 10 RG 213/U RG 58/U

Capacity pF/m 78 101 102Velocity factor 0,85 0,66 0,66attenuation dB/100 m

10 MHz 1,2 2,0 5,0100 MHz 4,0 7,0 17,0500 MHz 9,6 17,0 39,0

1000 MHz 14,2 22,5 54,63000 MHz 27,0 58,5 118

max

ECOFLEX is a registered trademark of SSB-Electronic GmbH.

Due to production tolerances the RTL may have different characteristics

Low loss coaxial cable for radio communications

ECOFLEX 15 is a flexible low-losscoaxial cable for use in the frequencyrange of DC - 6 GHz.

Its unique construction combines the low lossproperties found in non-flexible solid centerconductor hardline cables with the high flexibilityof cables manufactured with stranded center con-ductors.

Advanced manufacturing techniques combined with theuse of a PE-LLC Dielectric yields a foaming rate of morethan 70%, resulting in very low attenuation.

The use of continuous center conductor calibration andcompression as well as the application of a precoating gua-rantees low losses and stable impedance matching.

An EMI screening immunity of > 90 dB at 1.0 GHz is achie-ved through the use of double shielding which consists ofoverlapping copper foil and an additional tight woven cop-perbraid. The copperfoil has an applied PE coating whichprevents foil cracking due to short radius bends.The black PVC sheath of ECOFLEX 15 is uv-stabilized.

ECOFLEX 15 is the 1st choice when a low loss, highlyflexible microwave rated cable is required. It´s eco-nomical price makes ECOFLEX 15 the clearleader for today´s demanding applications.

Solder-free, high quality connectors in “N” and “7-16” havebeen specially developed for ECOFLEX 15. Connectorinstallation only takes a few minutes and requires no speci-al tools.

ECOFLEX 15 is available from stock in the following stan-dard drum sizes:25m, 50m, 100m, 200m and 500m.

ECOFLEX® 15 Connectors

Art.-Nr. 7395 N-plug, male, solderless

Art.-Nr. 7397 N-plug, female, solderless

Art.-Nr. 7398 7/16 DIN-plug male, solderless

CharacteristicsDiameter 14,6 mmImpedance 50 OhmAttenuation @ 1 GHz/100m 9,8 dBAttenuation @ 1 GHz/100ft 2,99 dB f 6 GHzmax

Frequency (GHz)

-10 dB-15 dB-20 dB-25 dB-30 dB-35 dB-40 dB

0,0 0,5 1,0 1,5 2,0 2,5 3,5 4,0 4,5 5,0 5,5 6,03,0

-5 dB0 dB

Technical dataConstructionCentre conductor stranded copper, oxygen free

7 x 1,55 mmCentre conductor Ø 4,5 mmDielectric low loss compound PEDielectric Ø 11,3 mmOuter conductor 1 copperfoil, PE coatedShielding factor 100%Outer conductor 2 copper braid, 72%Sheath black PVC, uv-resistantOuter diameter Ø 14,6 mm

Mechanical specificationsWeight (100 m) 25,8 kgMin. bending radius 70 mmTemperature range - 40 .... + 85 °CPulling strength 12 daN

Electrical specificationsImpedance 50 OhmCapacity 77 pF/mVelocity factor 0,86f 6 GHzScreening efficiency @ 1 GHz > 90 dBDC-resistance

Centre conductor 1,56 Ohm/kmOuter conductor 5,15 Ohm/km

RF peak voltage 1,55 kV

Max. power handling (W @40°C)10 MHz 6450

100 MHz 1970500 MHz 830

1000 MHz 5602000 MHz 3803000 MHz 3004000 MHz 250

6000 MHz 190

Typ. attenuation (dB/100m@20°C) dB/100ft @20°C5 MHz 0,6 0,18

10 MHz 0,86 0,26 50 MHz 1,96 0,60

100 MHz 2,81 0,86144 MHz 3,4 1,04200 MHz 4,05 1,23300 MHz 5,0 1,52432 MHz 6,1 1,86500 MHz 6,7 2,04800 MHz 8,6 2,62

1000 MHz 9,8 2,991296 MHz 11,4 3,481500 MHz 12,4 3,781800 MHz 13,8 4,212000 MHz 14,7 4,482400 MHz 16,3 4,973000 MHz 18,7 5,704000 MHz 22,3 6,805000 MHz 25,7 7,846000 MHz 28,8 8,78

100 dB

10 dB

1dB

0,1 dB30 100 1000 6000

Frequency (MHz)

AccessoriesGrounding clamp Art.-Nr. 6086

Attenuation (dB/100 m) @ 20°C

Return loss

For your informationationECOFLEX 15 RG 213/U RG 58/U

Capacity pF/m 77 101 102Velocity factor 0,86 0,66 0,66attenuation dB/100 m

10 MHz 0,86 2,0 5,0100 MHz 2,81 7,0 17,0500 MHz 6,7 17,0 39,0

1000 MHz 9,8 22,5 54,63000 MHz 18,7 58,5 118

max

ECOFLEX is a registered trademark of SSB-Electronic GmbH.

Due to production tolerances the RTL may have different characteristics

AIRCOM, AIRCELL, ECOFLEX are registered trademark of SSB-Electronic GmbH.