Air slide Conveying System
-
Upload
mahmoud-n-homran -
Category
Documents
-
view
436 -
download
7
description
Transcript of Air slide Conveying System
-
Designed for dependability.Proven to perform.
Fuller Airslide System OperationAir-activated gravity conveyorFluidization of material on the Airslide mediaFluidization reduces the angle of repose causing flow.Example: A material with a normal angle repose of 45 with fluidization may flow like a liquid on a 5 to 6 slope
Manufacturing StandardsHeavy-gauge steel sections with bent flangesAirslide conveyors are shipped in standard section lengths of 3 metersStandard widths of fluidized area is 4 up to 34 (100 to 850mm)Bolted airtight constructionOptional media available for high temperature and highly abrasive materialsThere is no conveying length limitation to the Airslide conveyor based upon availability of
headroom and proper slope.
Proprietary Airslide FabricProprietary weave designed for air gravity conveyorsEven permeability over the entire length of fabric
requires only one air connection every 100 feet -(30 meters)no dead zones -
Fluidized material chamber
Porous membrane
fabric
A. Blank End PlateB. Air ConnectionC. Air Control ValveD. Positive Displacement BlowerE. FanF. Rotary Cut-Off ValveG. Inlet NeckH. Butterfly Flow GateI. Rotary Metering Flow Gate
J. Side Discharge ValveK. Observation PortL. TurnboxM. Discharge BoxN. Vent ConnectionO. Airslide Conveyor Swivel AssemblyP. Telescopic Loading SpoutQ. Fuller-Kinyon Pump
A
B
C D
E
FGH
IJK
LLM
N
O
P
Q
FlexibilityNo additional conveyors needed to change -directions
Single Power SourceOne blower or fan is sufficient for system -
High Capacity / Long DistanceConveying volumes up to 1,500 cubic meters -(56,000 cu. ft.) and conveying distances in the 100s of feet/meters
Airslide Conveying Multiple Inlet to Multiple Outlets
www.fls-pt.com
Up-to-date addresses of worldwide subsidiaries and sales offices are available from our website
DENMARKFLSmidth A/SVigerslev All 77DK-2500 ValbyCopenhagenTel: +45 36 18 10 00Fax: +45 36 30 18 20Email: [email protected]
USAFLSmidth Inc.2040 Avenue CBethlehem, PA 18017-2188Tel: +1 610-264-6011Tel: +1 800-523-9482Fax: +1 610-264-6170Email: [email protected]
INDIAFLSmidth Private LimitedFLSmidth House34, Egatoor, Kelambakkam(Rajiv Gandhi Salai - Chennai)Tamil Nadu 603 103Tel: +91-44-4748 1000Fax:+91-44-2747 0301E-mail: [email protected]
07-2
009
AIR
SLID
E
FLSmidth 2009. This brochure makes no offers, representations or warranties (express or implied), and information and data contained in this brochure are for general reference only and may change at any time. Please contact us for specific information or data that may relate to your interests.
Fuller Airslide Conveying
Media Options
Section Material Application
F Woven 5-ply polyester Standard up to 350F (177C)
FN Needle felt non-wovenStandard non-silo bottom
applications
FS Silicon-treated polyester Special for static dissipation
KN Needle kevlar fabricStandard non-silo bottom
applications up to 475F (246C)
K Woven kevlar fabricStandard including silo bottom
applications up to 475F (246C)
GAX 19 Woven fiberglassHigh temperature up to 850F
(454C)
c
D
B
A
BSee chart below for dimensions
Hi-Top Design
Size A Nominal capacity B C D Weight
Type mm (1) cu.ft./hr. cu.m/hr. (1) in. mm (1) in. mm (1) in. mm lb./ft. kg./m
4 100 720 20 1.25 32 7.87 200 2.95 75 13 19
6 150 1200 34 1.25 32 7.87 200 2.95 75 15 22
8 200 3060 87 1.25 32 11.81 300 2.95 75 20 30
10 250 4030 114 1.25 32 11.81 300 2.95 75 22 33
12 300 7620 216 1.25 32 15.75 400 2.95 75 26 39
14 350 12700 360 1.25 32 19.69 500 2.95 75 30 45
16 400 15000 425 1.25 32 19.69 500 2.95 75 32 48
19 480 21200 600 1.50 38 22.05 560 2.95 75 38 57
24 600 56000 1586 2.25 57 23.62 600 3.94 100 46 68
34 850 87000 2464 3.0 76 35.83 910 3.94 100 100 149Nominal capacity ratings are based upon loose poured bulk density of the material and proper application. (1) English dimensions and capacities are nominal
Fuller Airslide Conveying Technology
Economical, energy-efficient
High capacity, high performance
Versatile and reliable
Fluidized Gravity Conveying Systems
Low pressureair chamber
(.5 - 5.0 psi, or 35 - 345 mbar)
-
AIR
SLI
DE
C
ON
VE
YIN
G T
EC
HN
OLO
GY Engineered systems
Single source responsibility
Global service and technology support
Reliable designs based upon experience
The Free Power of Gravity
FLSmidths Airslide Air Gravity Conveying System uses the forces of gravity to do most of the work without any moving parts. Material is fluidized through a porous media with low pressure air. Material flow is achieved by sloping the Airslide conveyor to match the fluidized angle of repose of the powdered material. At the correct slope, fluidized materials flow with the consistency of a liquid.
Airslide Air Gravity systems provide high-capacity material handling while offering many economical and environmental advantages. Energy requirements are minimal because only a small volume of air at a low pressure is required to move material. Since the system is installed overhead, valuable floor space and added headroom are available for other purposes. By eliminating the need for massive support members, it permits a flexibility of plant design not available with straight-line conveyors.The Airslide conveyor is dust tight. As a result, the system is extremely friendly to the environment.
Noise level is extremely low in the area surrounding the Airslide conveyor as the systems air supply is the only moving part to generate noise, and it is generally located in a remotely insulated area to further reduce noise.Maintenance of the Airslide conveyor is very simple because there are no moving parts other than the air supply equipment, which also contributes to increased plant safety. Airslide conveyors require no lubrication.
Typical Airslide Conveyor ApplicationsDistribution from bucket elevators to storage silosGathering under baghouses / precipitatorsFeed to processFeed to other conveyorsLoadout from bulk silos to trucks, railcars or bargesIn-plant conveyingStorage silo / bin withdrawal
The Principle of Fluidization: Driving low-pressure, low-velocity air through and between particles of a dry bulk material, changing its behavior characteristics and making it flow more like a liquid than a solid
All fly ash has a natural angle of repose, often in excess of 45 degrees.
1
Positive flow regulation (low - high capacities)Quiet operationLow maintenance no rotating parts in contact with materials being conveyedFully fluidized gentle conveying actionMinimized wear from abrasion
Airslide Conveying: Quiet & Simple Point-to-Point Transfer
Generally, materials passing through 35 mesh US std. (500 microns) can be conveyed through an Airslide Conveyor
Enlarged detail
AluminaBarytesBentoniteCalcined magnesiteCement raw and finish materialClayFly ash
Ground oresGypsumLime/LimestonePhosphatesPrecipitator dustResinsSilicaand more
Proven Airslide Applications
Airslide Conveyor Gathering for Dust CollectorsLow maintenance
No moving parts -Minimal fabric wear (change out required every 5-10 years) -
Low noise level - blower noise onlyCleanOperates smoothly regardless of downstream equipment rate
Airslide Conveyor FluidizationFLSmidth Airslide Aeration Unit Packages are supplied for installation as aeration units on the sloped conical bottoms of bins and silos to aid in the withdrawal of dry, relatively free-flowing material.
Withdrawal of dry, free-flowing materialsFor bins and silosThree or six spoke configurationsReplaces vibrating bin activatorsNo fatigue-inducing forces imparted into vesselAerated bin bottoms
From Silo Typical isolation and flow control
valve arrangement
Drum roller
Nearly maintenance-freeCapital cost reduced by as much as 50%Continuous product removal from collection hoppersOnly two moving pieces between collection hopper and storageContinuous conveying to storage
A2P: Airslide Conveyor to FK Pump Continuous Conveying System
FLSmidths Airslide Conveyor is a main component in the A2P Continuous Conveying system.
Airslide System Recirculation: SO2 Mitigation - Circulating Dry ScrubbersFor pebble lime and limestone (unloading, conveying and injection)Most new plants will be designed with some form of SO2 mitigation in the form of wet or dry scrubbers.
Such scrubbers are also being retrofitted on existing plants for (a) environmental compliance and (b) to allow for the switch to less expensive high sulphur coals.
Standard FLSmidth Airslide systems can be employed for all of these lime-based handling applications. Specialized circulating dry scrubbers (CDS) all employ FLSmidth Airslide technology.
Dryscrubber
Fuller Airlift and Airslide conveying systems convey alumina at a net rate of 750 mtph in a major western United States facility
RailcarHigh-capacity loading and unloading
TrailerDust-controlled loading and unloading
Large Diameter SilosEfficient filling and unloading systemsUniform filling systemFluidized silo bottom
Airslide Loading and Unloading Systems
Aerated bin bottom
changing its behavior characteristics and making it flow more like a liquid than a solid
With fluidization, gravity flow can be achieved at a greatly reduced slope -
of 8 degrees or less.
3
8
often in excess of 45 degrees.
Without any fluidization, the Airslide conveyor would have to be inclined on an angle greater than the angle of repose to establish gravity flow.
> 452
All fly ash has a natural angle of repose, 1often in excess of 45 degrees.
45
-
AIR
SLI
DE
C
ON
VE
YIN
G T
EC
HN
OLO
GY Engineered systems
Single source responsibility
Global service and technology support
Reliable designs based upon experience
The Free Power of Gravity
FLSmidths Airslide Air Gravity Conveying System uses the forces of gravity to do most of the work without any moving parts. Material is fluidized through a porous media with low pressure air. Material flow is achieved by sloping the Airslide conveyor to match the fluidized angle of repose of the powdered material. At the correct slope, fluidized materials flow with the consistency of a liquid.
Airslide Air Gravity systems provide high-capacity material handling while offering many economical and environmental advantages. Energy requirements are minimal because only a small volume of air at a low pressure is required to move material. Since the system is installed overhead, valuable floor space and added headroom are available for other purposes. By eliminating the need for massive support members, it permits a flexibility of plant design not available with straight-line conveyors.The Airslide conveyor is dust tight. As a result, the system is extremely friendly to the environment.
Noise level is extremely low in the area surrounding the Airslide conveyor as the systems air supply is the only moving part to generate noise, and it is generally located in a remotely insulated area to further reduce noise.Maintenance of the Airslide conveyor is very simple because there are no moving parts other than the air supply equipment, which also contributes to increased plant safety. Airslide conveyors require no lubrication.
Typical Airslide Conveyor ApplicationsDistribution from bucket elevators to storage silosGathering under baghouses / precipitatorsFeed to processFeed to other conveyorsLoadout from bulk silos to trucks, railcars or bargesIn-plant conveyingStorage silo / bin withdrawal
The Principle of Fluidization: Driving low-pressure, low-velocity air through and between particles of a dry bulk material, changing its behavior characteristics and making it flow more like a liquid than a solid
All fly ash has a natural angle of repose, often in excess of 45 degrees.
1
Positive flow regulation (low - high capacities)Quiet operationLow maintenance no rotating parts in contact with materials being conveyedFully fluidized gentle conveying actionMinimized wear from abrasion
Airslide Conveying: Quiet & Simple Point-to-Point Transfer
Generally, materials passing through 35 mesh US std. (500 microns) can be conveyed through an Airslide Conveyor
Enlarged detail
AluminaBarytesBentoniteCalcined magnesiteCement raw and finish materialClayFly ash
Ground oresGypsumLime/LimestonePhosphatesPrecipitator dustResinsSilicaand more
Proven Airslide Applications
Airslide Conveyor Gathering for Dust CollectorsLow maintenance
No moving parts -Minimal fabric wear (change out required every 5-10 years) -
Low noise level - blower noise onlyCleanOperates smoothly regardless of downstream equipment rate
Airslide Conveyor FluidizationFLSmidth Airslide Aeration Unit Packages are supplied for installation as aeration units on the sloped conical bottoms of bins and silos to aid in the withdrawal of dry, relatively free-flowing material.
Withdrawal of dry, free-flowing materialsFor bins and silosThree or six spoke configurationsReplaces vibrating bin activatorsNo fatigue-inducing forces imparted into vesselAerated bin bottoms
From Silo Typical isolation and flow control
valve arrangement
Drum roller
Nearly maintenance-freeCapital cost reduced by as much as 50%Continuous product removal from collection hoppersOnly two moving pieces between collection hopper and storageContinuous conveying to storage
A2P: Airslide Conveyor to FK Pump Continuous Conveying System
FLSmidths Airslide Conveyor is a main component in the A2P Continuous Conveying system.
Airslide System Recirculation: SO2 Mitigation - Circulating Dry ScrubbersFor pebble lime and limestone (unloading, conveying and injection)Most new plants will be designed with some form of SO2 mitigation in the form of wet or dry scrubbers.
Such scrubbers are also being retrofitted on existing plants for (a) environmental compliance and (b) to allow for the switch to less expensive high sulphur coals.
Standard FLSmidth Airslide systems can be employed for all of these lime-based handling applications. Specialized circulating dry scrubbers (CDS) all employ FLSmidth Airslide technology.
Dryscrubber
Fuller Airlift and Airslide conveying systems convey alumina at a net rate of 750 mtph in a major western United States facility
RailcarHigh-capacity loading and unloading
TrailerDust-controlled loading and unloading
Large Diameter SilosEfficient filling and unloading systemsUniform filling systemFluidized silo bottom
Airslide Loading and Unloading Systems
Aerated bin bottom
changing its behavior characteristics and making it flow more like a liquid than a solid
With fluidization, gravity flow can be achieved at a greatly reduced slope -
of 8 degrees or less.
3
8
often in excess of 45 degrees.
Without any fluidization, the Airslide conveyor would have to be inclined on an angle greater than the angle of repose to establish gravity flow.
> 452
All fly ash has a natural angle of repose, 1often in excess of 45 degrees.
45
-
AIR
SLI
DE
C
ON
VE
YIN
G T
EC
HN
OLO
GY Engineered systems
Single source responsibility
Global service and technology support
Reliable designs based upon experience
The Free Power of Gravity
FLSmidths Airslide Air Gravity Conveying System uses the forces of gravity to do most of the work without any moving parts. Material is fluidized through a porous media with low pressure air. Material flow is achieved by sloping the Airslide conveyor to match the fluidized angle of repose of the powdered material. At the correct slope, fluidized materials flow with the consistency of a liquid.
Airslide Air Gravity systems provide high-capacity material handling while offering many economical and environmental advantages. Energy requirements are minimal because only a small volume of air at a low pressure is required to move material. Since the system is installed overhead, valuable floor space and added headroom are available for other purposes. By eliminating the need for massive support members, it permits a flexibility of plant design not available with straight-line conveyors.The Airslide conveyor is dust tight. As a result, the system is extremely friendly to the environment.
Noise level is extremely low in the area surrounding the Airslide conveyor as the systems air supply is the only moving part to generate noise, and it is generally located in a remotely insulated area to further reduce noise.Maintenance of the Airslide conveyor is very simple because there are no moving parts other than the air supply equipment, which also contributes to increased plant safety. Airslide conveyors require no lubrication.
Typical Airslide Conveyor ApplicationsDistribution from bucket elevators to storage silosGathering under baghouses / precipitatorsFeed to processFeed to other conveyorsLoadout from bulk silos to trucks, railcars or bargesIn-plant conveyingStorage silo / bin withdrawal
The Principle of Fluidization: Driving low-pressure, low-velocity air through and between particles of a dry bulk material, changing its behavior characteristics and making it flow more like a liquid than a solid
All fly ash has a natural angle of repose, often in excess of 45 degrees.
1
Positive flow regulation (low - high capacities)Quiet operationLow maintenance no rotating parts in contact with materials being conveyedFully fluidized gentle conveying actionMinimized wear from abrasion
Airslide Conveying: Quiet & Simple Point-to-Point Transfer
Generally, materials passing through 35 mesh US std. (500 microns) can be conveyed through an Airslide Conveyor
Enlarged detail
AluminaBarytesBentoniteCalcined magnesiteCement raw and finish materialClayFly ash
Ground oresGypsumLime/LimestonePhosphatesPrecipitator dustResinsSilicaand more
Proven Airslide Applications
Airslide Conveyor Gathering for Dust CollectorsLow maintenance
No moving parts -Minimal fabric wear (change out required every 5-10 years) -
Low noise level - blower noise onlyCleanOperates smoothly regardless of downstream equipment rate
Airslide Conveyor FluidizationFLSmidth Airslide Aeration Unit Packages are supplied for installation as aeration units on the sloped conical bottoms of bins and silos to aid in the withdrawal of dry, relatively free-flowing material.
Withdrawal of dry, free-flowing materialsFor bins and silosThree or six spoke configurationsReplaces vibrating bin activatorsNo fatigue-inducing forces imparted into vesselAerated bin bottoms
From Silo Typical isolation and flow control
valve arrangement
Drum roller
Nearly maintenance-freeCapital cost reduced by as much as 50%Continuous product removal from collection hoppersOnly two moving pieces between collection hopper and storageContinuous conveying to storage
A2P: Airslide Conveyor to FK Pump Continuous Conveying System
FLSmidths Airslide Conveyor is a main component in the A2P Continuous Conveying system.
Airslide System Recirculation: SO2 Mitigation - Circulating Dry ScrubbersFor pebble lime and limestone (unloading, conveying and injection)Most new plants will be designed with some form of SO2 mitigation in the form of wet or dry scrubbers.
Such scrubbers are also being retrofitted on existing plants for (a) environmental compliance and (b) to allow for the switch to less expensive high sulphur coals.
Standard FLSmidth Airslide systems can be employed for all of these lime-based handling applications. Specialized circulating dry scrubbers (CDS) all employ FLSmidth Airslide technology.
Dryscrubber
Fuller Airlift and Airslide conveying systems convey alumina at a net rate of 750 mtph in a major western United States facility
RailcarHigh-capacity loading and unloading
TrailerDust-controlled loading and unloading
Large Diameter SilosEfficient filling and unloading systemsUniform filling systemFluidized silo bottom
Airslide Loading and Unloading Systems
Aerated bin bottom
changing its behavior characteristics and making it flow more like a liquid than a solid
With fluidization, gravity flow can
be achieved at a greatly reduced slope -
of 8 degrees or less.
3
8
often in excess of 45 degrees.
Without any fluidization, the Airslide conveyor would have to be inclined on an angle greater than the angle of repose to establish gravity flow.
> 452
All fly ash has a natural angle of repose, 1often in excess of 45 degrees.
45
-
Designed for dependability.Proven to perform.
Fuller Airslide System OperationAir-activated gravity conveyorFluidization of material on the Airslide mediaFluidization reduces the angle of repose causing flow.Example: A material with a normal angle repose of 45 with fluidization may flow like a liquid on a 5 to 6 slope
Manufacturing StandardsHeavy-gauge steel sections with bent flangesAirslide conveyors are shipped in standard section lengths of 3 metersStandard widths of fluidized area is 4 up to 34 (100 to 850mm)Bolted airtight constructionOptional media available for high temperature and highly abrasive materialsThere is no conveying length limitation to the Airslide conveyor based upon availability of
headroom and proper slope.
Proprietary Airslide FabricProprietary weave designed for air gravity conveyorsEven permeability over the entire length of fabric
requires only one air connection every 100 feet -(30 meters)no dead zones -
Proven to perform.Fuller
Manufacturing Standards
Fluidized material chamber
Porous membrane
fabric
A. Blank End PlateB. Air ConnectionC. Air Control ValveD. Positive Displacement BlowerE. FanF. Rotary Cut-Off ValveG. Inlet NeckH. Butterfly Flow GateI. Rotary Metering Flow Gate
J. Side Discharge ValveK. Observation PortL. TurnboxM. Discharge BoxN. Vent ConnectionO. Airslide Conveyor Swivel AssemblyP. Telescopic Loading SpoutQ. Fuller-Kinyon Pump
(30 meters)no dead zones-
A. Blank End PlateB. Air ConnectionC. Air Control ValveD. Positive Displacement BlowerE. FanF. Rotary Cut-Off ValveG. Inlet NeckH. Butterfly Flow Gate
J. Side Discharge ValveK. Observation PortL. TurnboxM. Discharge BoxN. Vent ConnectionO. Airslide Conveyor Swivel AssemblyP. Telescopic Loading Spout
A
B
C D
E
FGH
IJK
LLM
N
O
P
Q
FlexibilityNo additional conveyors needed to change -directions
Single Power SourceOne blower or fan is sufficient for system -
High Capacity / Long DistanceConveying volumes up to 1,500 cubic meters -(56,000 cu. ft.) and conveying distances in the 100s of feet/meters
Airslide Conveying Multiple Inlet to Multiple Outlets
www.fls-pt.com
Up-to-date addresses of worldwide subsidiaries and sales offices are available from our website
DENMARKFLSmidth A/SVigerslev All 77DK-2500 ValbyCopenhagenTel: +45 36 18 10 00Fax: +45 36 30 18 20Email: [email protected]
USAFLSmidth Inc.2040 Avenue CBethlehem, PA 18017-2188Tel: +1 610-264-6011Tel: +1 800-523-9482Fax: +1 610-264-6170Email: [email protected]
INDIAFLSmidth Private LimitedFLSmidth House34, Egatoor, Kelambakkam(Rajiv Gandhi Salai - Chennai)Tamil Nadu 603 103Tel: +91-44-4748 1000Fax:+91-44-2747 0301E-mail: [email protected]
07-2
009
AIR
SLID
E
FLSmidth 2009. This brochure makes no offers, representations or warranties (express or implied), and information and data contained in this brochure are for general reference only and may change at any time. Please contact us for specific information or data that may relate to your interests.
Fuller Airslide Conveying
Media Options
Section Material Application
F Woven 5-ply polyester Standard up to 350F (177C)
FN Needle felt non-wovenStandard non-silo bottom
applications
FS Silicon-treated polyester Special for static dissipation
KN Needle kevlar fabricStandard non-silo bottom
applications up to 475F (246C)
K Woven kevlar fabricStandard including silo bottom
applications up to 475F (246C)
GAX 19 Woven fiberglassHigh temperature up to 850F
(454C)
c
D
B
A
BSee chart below for dimensions
Hi-Top Design
Size A Nominal capacity B C D Weight
Type mm (1) cu.ft./hr. cu.m/hr. (1) in. mm (1) in. mm (1) in. mm lb./ft. kg./m
4 100 720 20 1.25 32 7.87 200 2.95 75 13 19
6 150 1200 34 1.25 32 7.87 200 2.95 75 15 22
8 200 3060 87 1.25 32 11.81 300 2.95 75 20 30
10 250 4030 114 1.25 32 11.81 300 2.95 75 22 33
12 300 7620 216 1.25 32 15.75 400 2.95 75 26 39
14 350 12700 360 1.25 32 19.69 500 2.95 75 30 45
16 400 15000 425 1.25 32 19.69 500 2.95 75 32 48
19 480 21200 600 1.50 38 22.05 560 2.95 75 38 57
24 600 56000 1586 2.25 57 23.62 600 3.94 100 46 68
34 850 87000 2464 3.0 76 35.83 910 3.94 100 100 149Nominal capacity ratings are based upon loose poured bulk density of the material and proper application. (1) English dimensions and capacities are nominal
Fuller Airslide Conveying Technology
Economical, energy-efficient
High capacity, high performance
Versatile and reliable
Fluidized Gravity Conveying Systems
Low pressureair chamber
(.5 - 5.0 psi, or 35 - 345 mbar)
-
Designed for dependability.Proven to perform.
Fuller Airslide System OperationAir-activated gravity conveyorFluidization of material on the Airslide mediaFluidization reduces the angle of repose causing flow.Example: A material with a normal angle repose of 45 with fluidization may flow like a liquid on a 5 to 6 slope
Manufacturing StandardsHeavy-gauge steel sections with bent flangesAirslide conveyors are shipped in standard section lengths of 3 metersStandard widths of fluidized area is 4 up to 34 (100 to 850mm)Bolted airtight constructionOptional media available for high temperature and highly abrasive materialsThere is no conveying length limitation to the Airslide conveyor based upon availability of
headroom and proper slope.
Proprietary Airslide FabricProprietary weave designed for air gravity conveyorsEven permeability over the entire length of fabric
requires only one air connection every 100 feet -(30 meters)no dead zones -
Fluidized material chamber
Porous membrane
fabric
A. Blank End PlateB. Air ConnectionC. Air Control ValveD. Positive Displacement BlowerE. FanF. Rotary Cut-Off ValveG. Inlet NeckH. Butterfly Flow GateI. Rotary Metering Flow Gate
J. Side Discharge ValveK. Observation PortL. TurnboxM. Discharge BoxN. Vent ConnectionO. Airslide Conveyor Swivel AssemblyP. Telescopic Loading SpoutQ. Fuller-Kinyon Pump
A
B
C D
E
FGH
IJK
LLM
N
O
P
Q
FlexibilityNo additional conveyors needed to change -directions
Single Power SourceOne blower or fan is sufficient for system -
High Capacity / Long DistanceConveying volumes up to 1,500 cubic meters -(56,000 cu. ft.) and conveying distances in the 100s of feet/meters
Airslide Conveying Multiple Inlet to Multiple Outlets
www.fls-pt.com
Up-to-date addresses of worldwide subsidiaries and sales offices are available from our website
DENMARKFLSmidth A/SVigerslev All 77DK-2500 ValbyCopenhagenTel: +45 36 18 10 00Fax: +45 36 30 18 20Email: [email protected]
USAFLSmidth Inc.2040 Avenue CBethlehem, PA 18017-2188Tel: +1 610-264-6011Tel: +1 800-523-9482Fax: +1 610-264-6170Email: [email protected]
INDIAFLSmidth Private LimitedFLSmidth House34, Egatoor, Kelambakkam(Rajiv Gandhi Salai - Chennai)Tamil Nadu 603 103Tel: +91-44-4748 1000Fax:+91-44-2747 0301E-mail: [email protected]
10-2
009
AIR
SLID
E
FLSmidth 2009. This brochure makes no offers, representations or warranties (express or implied), and information and data contained in this brochure are for general reference only and may change at any time. Please contact us for specific information or data that may relate to your interests.
Fuller Airslide Conveying
Media Options
Section Material Application
F Woven 5-ply polyester Standard up to 350F (177C)
FN Needle felt non-wovenStandard non-silo bottom
applications
FS Silicon-treated polyester Special for static dissipation
KN Needle kevlar fabricStandard non-silo bottom
applications up to 475F (246C)
K Woven kevlar fabricStandard including silo bottom
applications up to 475F (246C)
GAX 19 Woven fiberglassHigh temperature up to 850F
(454C)
c
D
B
A
BSee chart below for dimensions
Hi-Top Design
Size A Nominal capacity B C D Weight
Type mm (1) cu.ft./hr. cu.m/hr. (1) in. mm (1) in. mm (1) in. mm lb./ft. kg./m
4 100 720 20 1.25 32 7.87 200 2.95 75 13 19
6 150 1200 34 1.25 32 7.87 200 2.95 75 15 22
8 200 3060 87 1.25 32 11.81 300 2.95 75 20 30
10 250 4030 114 1.25 32 11.81 300 2.95 75 22 33
12 300 7620 216 1.25 32 15.75 400 2.95 75 26 39
14 350 12700 360 1.25 32 19.69 500 2.95 75 30 45
16 400 15000 425 1.25 32 19.69 500 2.95 75 32 48
19 480 21200 600 1.50 38 22.05 560 2.95 75 38 57
24 600 56000 1586 2.25 57 23.62 600 3.94 100 46 68
34 850 87000 2464 3.0 76 35.83 910 3.94 100 100 149Nominal capacity ratings are based upon loose poured bulk density of the material and proper application. (1) English dimensions and capacities are nominal
Fuller Airslide Conveying Technology
Economical, energy-efficient
High capacity, high performance
Versatile and reliable
Fluidized Gravity Conveying Systems
Low pressureair chamber
(.5 - 5.0 psi, or 35 - 345 mbar)