Aerial Catalog 2_21

BV-35 Vertical Tap/Angle Bracket Description: The BV-35 is a vertical tap/angle bracket used with Hendrix Spacer Cable Systems. The bracket is formed using 3.0” channel and is hot dip galvanized after fabrication. Benefits: • The phase conductors are supported in a vertical orientation to permit taps to be made while still maintaining a compact configuration • Simple, compact alternative to crossarm angle or tap construction • Ground Lug Provision Application: The BV-35 is designed for primary lateral taps at all voltages through 35kV. These brackets can also be used on angles up to 90°in applications where a vertical configuration of the phase conductors is desired. The bracket should be applied along with Hendrix HPI polyethylene insulators and covered tie wire or HPI Vise-Top Insulators with 2IP plate, if required. Pole mounting is accom- plished using thru-bolts (not included). Dimension (inches) Minimum Yield Load (lbs) Weight Catalog No. A B C D E F V1 V2 V3 (lbs) Material BV-35 17 3 /8 2 1 /2 18 3 / 4 37 5 / 8 26 7 / 8 13 /16 1,150 1,600 1,100 17.3 HDG ASTM A-36 Structural Steel System Voltage Line Angle Conductor Size 2IP Plate 15kV 7°- 60° All conductors not required 61°- 90° All conductors required 7°- 44° All conductors not required 45°- 60° Below 336.4 not required 25/35kV 45°- 60° 336.4 and larger required 61°- 90° All conductors required Angle Lateral tap Marmon Utility LLC. • 53 Old Wilton Road • Milford, NH 03055-3119 Telephone: (603) 673-2040 • Fax: (603) 673-1497 • Email: [email protected] • Website: http://www.hendrix-wc.com A Marmon Wire & Cable / Berkshire Hathaway Company 10/6 2-21

Upload
sebastian-almagro
Category

Documents
view
214
download
1

Embed Size (px):

description

Aerial Catalog 2_21

Transcript of Aerial Catalog 2_21

BV-35 Vertical Tap/Angle Bracket

Description:The BV-35 is a vertical tap/angle bracket used with Hendrix Spacer CableSystems. The bracket is formed using 3.0 channel and is hot dip galvanizedafter fabrication.

Benefits: The phase conductors are supported in a vertical orientation to permit taps to

be made while still maintaining a compact configuration

Simple, compact alternative to crossarm angle or tap construction

Ground Lug Provision

Application:The BV-35 is designed for primary lateral taps at all voltages through 35kV. These brackets can also be used on angles up to 90in applications where avertical configuration of the phase conductors is desired. The bracket should beapplied along with Hendrix HPI polyethylene insulators and covered tie wire orHPI Vise-Top Insulators with 2IP plate, if required. Pole mounting is accom-plished using thru-bolts (not included).

Dimension (inches) Minimum Yield Load (lbs) WeightCatalog No.

A B C D E F V1 V2 V3 (lbs)Material

BV-35 17 3/8 2 1/2 18 3/4 37 5/8 267/8 13/16 1,150 1,600 1,100 17.3HDG ASTM A-36

Structural Steel

System Voltage Line Angle Conductor Size 2IP Plate

15kV 7- 60 All conductors not required61- 90 All conductors required

7- 44 All conductors not required45- 60 Below 336.4 not required

25/35kV 45- 60 336.4 and larger required61- 90 All conductors required

AngleLateral tap

Marmon Utility LLC. 53 Old Wilton Road Milford, NH 03055-3119Telephone: (603) 673-2040 Fax: (603) 673-1497 Email: [email protected] Website: http://www.hendrix-wc.com

A Marmon Wire & Cable / Berkshire Hathaway Company 10/62-21