Advisory Note #45

ADVISORY NOTE #45.01

STANDARD SECTION PROPERTIES FOR HOT DIP GALVANIZING

Issue 1: June 2019

TABLE OF CONTENTS

Contents

STANDARD SECTION PROPERTIES FOR HOT DIP GALVANIZING ______________________________ 1

Introduction ____________________________________________________________________________ 1

How to Use the Tables ____________________________________________________________________ 1

Section Drawings ________________________________________________________________________ 2

Table 1 Equal Angles to AS/NZS 3679.1 ______________________________________________________ 1

Table 2 Unequal Angles to AS/NZS 3679.1 ____________________________________________________ 3

Table 3 Parallel Flange Channels to AS/NZS 3679.1 _____________________________________________ 4

Table 4 Universal Beams to AS/NZS 3679.1 ___________________________________________________ 5

Table 5 Universal Columns to AS/NZS 3679.1 _________________________________________________ 7

Table 6 Flat Bar to AS/NZS 3679.1 __________________________________________________________ 8

Table 7 Round Bar to AS/NZS 3679.1 _______________________________________________________ 12

Table 8 Rod to AS/NZS 3679.1 _____________________________________________________________ 14

Table 9 Square Bar to AS/NZS 3679.1 _______________________________________________________ 15

Table 10 Welded Beams to AS/NZS 3679.2 __________________________________________________ 16

Table 11 Welded Columns to AS/NZS 3679.2 _________________________________________________ 17

Table 12 Circular Hollow Sections (CHS) to AS/NZS 1163 _______________________________________ 18

Table 13 Rectangular Hollow Sections (RHS) to AS/NZS 1163 ____________________________________ 21

Table 14 Square Hollow Sections (SHS) TO AS/NZS 1163 ________________________________________ 24

Cover Image: Baldivis Secondary College, Parry and Rosenthal Architects / BPA Engineering. Photograph © Robert Frith - Acorn Photo

This Advisory Note is intended to keep readers abreast of current issues and developments in the field of galvanizing. The Galvanizers

Association of Australia has made every effort to ensure that the information provided is accurate, however its accuracy, reliability or

completeness is not guaranteed. Any advice given, information provided, or procedures recommended by GAA represent its best

solutions based on its information and research, however may be based on assumptions which while reasonable, may not be applicable

to all environments and potential fields of application. Due and proper consideration has been given to all information provided but no

warranty is made regarding the accuracy or reliability of either the information contained in this publication or any specific

recommendation made to the recipient. Comments made are of a general nature only and are not intended to be relied upon or to be

used as a substitute for professional advice. GAA and its employees disclaim all liability and responsibility for any direct or indirect loss

or damage which may be suffered by the recipient through relying on anything contained or omitted in this publication.


Standard Section Properties for Hot Dip Galvanizing Page 1

STANDARD SECTION PROPERTIES FOR HOT DIP GALVANIZING

INTRODUCTION

This Advisory Note contains tables showing the thickness, mass and coating area properties of standard structural steel sections used for hot dip galvanized articles.

The section properties have been derived from:

• AS/NZS 3679.1, Structural Steel – Part 1: Hot-rolled bars and sections

• AS/NZS 3679.2, Structural Steel – Part 2: Welded I sections

• AS/NZS 1163, Cold formed structural steel hollow sections

The coating properties have been derived from:

• AS/NZS 4680, Hot-dip galvanized (zinc) coatings on fabricated ferrous articles

All properties are based on nominal or minimum requirements of the relevant Standard and, particularly with the hot dip galvanized coating thickness, may understate the actual property. Where the coating thickness is important for durability design or sustainability calculations, reference should be made to the GAA or your GAA member galvanizer for more information. While the sections listed are those thought to be commonly available, designers should check specific availability with their steel supplier.

HOW TO USE THE TABLES

The tables provide an estimate of the coated area and the minimum increase in mass once the zinc coating is applied. It is important to recognise that the data is based on nominal section sizes and minimum required coating thicknesses. The actual properties will almost certainly differ from nominal, so the information should be used for guidance only.

The steel Standards include tolerances on shape as well as mass limits. Individual hot rolled sections are required to be no less than 97.% of the nominal mass and a group of products must be with ±2.5% of the nominal mass. Individual hollow sections (tubes) are required to be no less than 96% of the nominal mass.

The factors that affect the coating thickness include the steel thickness, venting and draining design, weld design, steel chemistry and surface roughness. It is not technically possible to coat only one surface of a tubular section, therefore the available coated surface for tubular sections in the tables always includes both the outer and inner surfaces.

Based on experience and as a guide only, most hot rolled structural sections with a minimum steel thickness of 10 mm will typically achieve a hot dip galvanized coating thickness of at least 125 µm, although the tables show only the requirement of the Australian Standard for > 6 mm steel thickness (85 µm). Some thinner sections can also achieve this outcome although agreement must always be obtained from the galvanizer prior to placing an order if non-standard coating thicknesses are required. Most cold formed tubular sections will require additional surface preparation (usually blasting) to achieve much thicker coatings than the nominal shown in the Standard and this document and this blasting is usually only available on the external surface.



This Advisory Note can be used in conjunction with the GAA Environmental Product Declaration (EPD) where there is a companion registered EPD for the substrate steel section. The EPD contains worked examples showing how to use these two documents to calculate the environmental impact of hot dip galvanized steel in Australia.

SECTION DRAWINGS

Equal Angles

AS/NZS 3679.1

Unequal Angles

AS/NZS 3679.1

Parallel Flange Channels

AS/NZS 3679.1

Universal Beams

AS/NZS 3679.1

Universal Columns

AS/NZS 3679.1

Flat Bar

AS/NZS 3679.1

Round Bar

AS/NZS 3679.1

Square Bar

AS/NZS 3679.1



Welded Beams

AS/NZS 3679.2

Welded Columns

AS/NZS 3679.2

CHS

AS/NZS 1163

RHS

AS/NZS 1163

SHS

AS/NZS 1163



Table 1 Equal Angles to AS/NZS 3679.1

DESIGNATION

(a x b x tn)

STEEL

COATED AREA

COATING

TOTAL MASS THICKNESS MASS THICKNESS MASS

ts ms tz mz mt

mm kg/m m2/m m2/t µm kg/m kg/m

200x200x26 EA 26.0 76.8 0.788 10.260 85 0.478 77.278

200x200x20 EA 20.0 60.1 0.788 13.111 85 0.478 60.578

200x200x18 EA 18.0 54.4 0.788 14.485 85 0.478 54.878

200x200x16 EA 16.0 48.7 0.788 16.181 85 0.478 49.178

200x200x13 EA 13.0 40.0 0.788 19.700 85 0.478 40.478

150x150x19 EA 19.0 42.1 0.590 14.014 85 0.358 42.458

150x150x16 EA 15.8 35.4 0.590 16.667 85 0.358 35.758

150x150x12 EA 12.0 27.3 0.590 21.612 85 0.358 27.658

150x150x10 EA 9.5 21.9 0.590 26.941 85 0.358 22.258

125x125x16 EA 15.8 29.1 0.491 16.873 85 0.298 29.398

125x125x12 EA 12.0 22.5 0.491 21.822 85 0.298 22.798

125x125x10 EA 9.5 18.0 0.491 27.278 85 0.298 18.298

125x125x8 EA 7.8 14.9 0.491 32.953 85 0.298 15.198

100x100x12 EA 12.0 17.7 0.392 22.147 85 0.238 17.938

100x100x10 EA 9.5 14.2 0.392 27.606 85 0.238 14.438

100x100x8 EA 7.8 11.8 0.392 33.220 85 0.238 12.038

100x100x6 EA 6.0 9.16 0.392 42.795 70 0.196 9.356

90x90x10 EA 9.5 12.7 0.352 27.717 85 0.214 12.914

90x90x8 EA 7.8 10.6 0.352 33.208 85 0.214 10.814

90x90x6 EA 6.0 8.22 0.352 42.822 70 0.176 8.396

75x75x10 EA 9.5 10.5 0.292 27.810 85 0.177 10.677

75x75x8 EA 7.8 8.73 0.292 33.448 85 0.177 8.907

75x75x6 EA 6.0 6.81 0.292 42.878 70 0.146 6.956

75x75x5 EA 4.6 5.27 0.292 55.408 70 0.146 5.416



DESIGNATION

(a x b x tn)

STEEL

COATED AREA

COATING

TOTAL MASS THICKNESS MASS THICKNESS MASS

ts ms tz mz mt


65x65x10 EA 9.5 9.02 0.255 28.271 85 0.155 9.175

65x65x8 EA 7.8 7.51 0.255 33.955 85 0.155 7.665

65x65x6 EA 6.0 5.87 0.255 43.441 70 0.127 5.997

65x65x5 EA 4.6 4.56 0.255 55.921 70 0.127 4.687

55x55x6 EA 6.0 4.93 0.215 43.611 70 0.107 5.037

55x55x5 EA 4.6 3.84 0.215 55.990 70 0.107 3.947

50x50x8 EA 7.8 5.68 0.195 34.331 85 0.118 5.798

50x50x6 EA 6.0 4.46 0.195 43.722 70 0.0975 4.557

50x50x5 EA 4.6 3.48 0.195 56.034 70 0.0975 3.577

50x50x3 EA 3.0 2.31 0.195 84.416 55 0.0766 2.387

45x45x6 EA 6.0 3.97 0.175 44.081 70 0.0875 4.057

45x45x5 EA 4.6 3.10 0.175 56.452 70 0.0875 3.187

45x45x3 EA 3.0 2.06 0.175 84.951 55 0.0687 2.129

40x40x6 EA 6.0 3.50 0.155 44.286 70 0.0775 3.577

40x40x5 EA 4.6 2.73 0.155 56.777 70 0.0775 2.807

40x40x3 EA 3.0 1.83 0.155 84.699 55 0.0609 1.891

30x30x6 EA 6.0 2.56 0.115 44.922 70 0.0575 2.617

30x30x5 EA 4.6 2.01 0.115 57.214 70 0.0575 2.067

30x30x3 EA 3.0 1.35 0.115 85.185 55 0.0452 1.395

25x25x6 EA 6.0 2.08 0.0953 45.817 70 0.0476 2.128

25x25x5 EA 4.6 1.65 0.0953 57.758 70 0.0476 1.698

25x25x3 EA 3.0 1.12 0.0953 85.089 55 0.0374 1.157

Note: For angles, the nominal steel thickness (tn) shown in the designation may vary from the actual steel thickness (ts). Refer to AS/NZS 3679.1 for more information.



Table 2 Unequal Angles to AS/NZS 3679.1

DESIGNATION

(a x b x tn)

STEEL

COATED AREA

COATING TOTAL MASS

THICKNESS MASS THICKNESS MASS

ts ms tz mz mt


150x100x12 UA 12.0 22.5 0.491 21.822 85 0.298 22.798

150x100x10 UA 9.5 18.0 0.491 27.278 85 0.298 18.298

150x90x16 UA 15.8 27.9 0.471 16.882 85 0.286 28.186

150x90x12 UA 12.0 21.6 0.471 21.806 85 0.286 21.886

150x90x10 UA 9.5 17.3 0.471 27.225 85 0.286 17.586

150x90x8 UA 7.8 14.3 0.471 32.937 85 0.286 14.586

125x75x12 UA 12.0 17.7 0.392 22.147 85 0.238 17.938

125x75x10 UA 9.5 14.2 0.392 27.606 85 0.238 14.438

125x75x8 UA 7.8 11.8 0.392 33.220 85 0.238 12.038

125x75x6 UA 6.0 9.16 0.392 42.795 70 0.196 9.356

100x75x10 UA 9.5 12.4 0.342 27.581 85 0.208 12.608

100x75x8 UA 7.8 10.3 0.342 33.204 85 0.208 10.508

100x75x6 UA 6.0 7.98 0.342 42.857 70 0.171 8.151

75x50x8 UA 7.8 7.23 0.244 33.748 85 0.148 7.378

75x50x6 UA 6.0 5.66 0.244 43.110 70 0.122 5.782

75x50x5 UA 4.6 4.40 0.244 55.455 70 0.122 4.522

65x50x8 UA 7.8 6.59 0.225 34.143 85 0.137 6.727

65x50x6 UA 6.0 5.16 0.225 43.605 70 0.112 5.272

65x50x5 UA 4.6 4.02 0.225 55.970 70 0.112 4.132

Note: For angles, the nominal steel thickness (tn) shown in the designation may vary from the actual steel thickness (ts). Refer to AS/NZS 3679.1 for more information.



Table 3 Parallel Flange Channels to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING

TOTAL MASS FLANGE THICKNESS WEB THICKNESS MASS THICKNESS MASS

tf tw ms tz mz mt

mm mm kg/m m2/m m2/t µm kg/m kg/m

380PFC 17.5 10.0 55.2 1.13 20.471 85 0.686 55.886

300PFC 16.0 8.0 40.1 0.932 23.242 85 0.566 40.666

250PFC 15.0 8.0 35.5 0.834 23.493 85 0.506 36.006

230PFC 12.0 6.5 25.1 0.737 29.363 85 0.447 25.547

200PFC 12.0 6.0 22.9 0.678 29.607 85 0.411 23.311

180PFC 11.0 6.0 20.9 0.638 30.526 85 0.387 21.287

150PFC 9.5 6.0 17.7 0.579 32.712 85 0.351 18.051

125PFC 7.5 4.7 11.9 0.494 41.513 85 0.300 12.200

100PFC 6.7 4.2 8.33 0.385 46.218 85 0.234 8.564

75PFC 6.1 3.8 5.92 0.296 50.000 85 0.180 6.100



Table 4 Universal Beams to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING

TOTAL MASS FLANGE THICKNESS

WEB THICKNESS MASS THICKNESS MASS

tf tw ms tz mz mt


610UB125 19.6 11.9 125 2.09 16.720 85 1.268 126.268

610UB113 17.3 11.2 113 2.08 18.407 85 1.262 114.262

610UB101 14.8 10.6 101 2.07 20.495 85 1.256 102.256

530UB92.4 15.6 10.2 92.4 1.86 20.130 85 1.129 93.529

530UB82.0 13.2 9.6 82.0 1.85 22.561 85 1.123 83.123

460UB82.1 16.0 9.9 82.1 1.65 20.097 85 1.001 83.101

460UB74.6 14.5 9.1 74.6 1.64 21.984 85 0.995 75.595

460UB67.1 12.7 8.5 67.1 1.63 24.292 85 0.989 68.089

410UB59.7 12.8 7.8 59.7 1.49 24.958 85 0.904 60.604

410UB53.7 10.9 7.6 53.7 1.48 27.561 85 0.898 54.598

360UB56.7 13.0 8.0 56.7 1.37 24.162 85 0.831 57.531

360UB50.7 11.5 7.3 50.7 1.36 26.824 85 0.825 51.525

360UB44.7 9.7 6.9 44.7 1.35 30.201 85 0.819 45.519

310UB46.2 11.8 6.7 46.2 1.25 27.056 85 0.759 46.959

310UB40.4 10.2 6.1 40.4 1.24 30.693 85 0.753 41.153

310UB32.0 8.0 5.5 32.0 1.16 36.250 85 0.704 32.704

250UB37.3 10.9 6.4 37.3 1.07 28.686 85 0.649 37.949

250UB31.4 8.6 6.1 31.4 1.06 33.758 85 0.643 32.043

250UB25.7 8.0 5.0 25.7 0.961 37.393 85 0.583 26.283

200UB29.8 9.6 6.3 29.8 0.922 30.940 85 0.560 30.360

200UB25.4 7.8 5.8 25.4 0.912 35.906 85 0.553 25.953

200UB22.3 7.0 5.0 22.3 0.91 40.807 85 0.552 22.852

200UB18.2 7.0 4.5 18.2 0.764 41.978 85 0.464 18.664



DESIGNATION

STEEL

COATED AREA

COATING



tf tw ms tz mz mt


180UB22.2 10.0 6.0 22.2 0.691 31.126 85 0.419 22.619

180UB18.1 8.0 5.0 18.1 0.685 37.845 85 0.416 18.516

180UB16.1 7.0 4.5 16.1 0.682 42.360 85 0.414 16.514

150UB18.0 9.5 6.0 18.0 0.584 32.444 85 0.354 18.354

150UB14.0 7.0 5.0 14.0 0.576 41.143 85 0.350 14.350



Table 5 Universal Columns to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING



tf tw ms tz mz mt


310UC158 25.0 15.7 158 1.84 11.646 85 1.117 159.117

310UC137 21.7 13.8 137 1.82 13.285 85 1.105 138.105

310UC118 18.7 11.9 118 1.81 15.339 85 1.098 119.098

310UC96.8 15.4 9.9 96.8 1.79 18.492 85 1.086 97.886

250UC89.5 17.3 10.5 89.5 1.5 16.760 85 0.910 90.410

250UC72.9 14.2 8.6 72.9 1.48 20.302 85 0.898 73.798

200UC59.5 14.2 9.3 59.5 1.22 20.504 85 0.740 60.240

200UC52.2 12.5 8.0 52.2 1.19 22.797 85 0.722 52.922

200UC46.2 11.0 7.3 46.2 1.18 25.541 85 0.716 46.916

150UC37.2 11.5 8.1 37.2 0.908 24.409 85 0.551 37.751

150UC30.0 9.4 6.6 30.0 0.899 29.967 85 0.546 30.546

150UC23.4 6.8 6.1 23.4 0.885 37.821 85 0.537 23.937

100UC14.8 7.0 5.0 14.8 0.563 38.041 85 0.342 15.142



Table 6 Flat Bar to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS

WIDTH THICKNESS MASS THICKNESS MASS

w ts ms tz mz mt


20x10 20 10 1.57 0.060 38.217 85 0.036 1.606

25x5 25 5 0.981 0.060 61.162 70 0.030 1.011

25x6 25 6 1.18 0.062 52.542 70 0.031 1.211

25x8 25 8 1.57 0.066 42.038 85 0.040 1.610

25x10 25 10 1.96 0.070 35.714 85 0.042 2.002

25x12 25 12 2.36 0.074 31.356 85 0.045 2.405

32x5 32 5 1.26 0.074 58.730 70 0.037 1.297

32x6 32 6 1.51 0.076 50.331 70 0.038 1.548

32x8 32 8 2.01 0.080 39.801 85 0.049 2.059

32x10 32 10 2.51 0.084 33.466 85 0.051 2.561

32x12 32 12 3.01 0.088 29.236 85 0.053 3.063

40x5 40 5 1.57 0.090 57.325 70 0.045 1.615

40x6 40 6 1.88 0.092 48.936 70 0.046 1.926

40x8 40 8 2.51 0.096 38.247 85 0.058 2.568

40x10 40 10 3.14 0.100 31.847 85 0.061 3.201

40x12 40 12 3.77 0.104 27.586 85 0.063 3.833

40x16 40 16 5.02 0.112 22.311 85 0.068 5.088

40x20 40 20 6.28 0.120 19.108 85 0.073 6.353

50x5 50 5 1.96 0.110 56.122 70 0.055 2.015

50x6 50 6 2.36 0.112 47.458 70 0.056 2.416

50x8 50 8 3.14 0.116 36.943 85 0.070 3.210

50x10 50 10 3.93 0.120 30.534 85 0.073 4.003

50x12 50 12 4.71 0.124 26.327 85 0.075 4.785

50x16 50 16 6.28 0.132 21.019 85 0.080 6.360



DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS


w ts ms tz mz mt


50x20 50 20 7.85 0.140 17.834 85 0.085 7.935

50x25 50 25 9.81 0.150 15.291 85 0.091 9.901

65x5 65 5 2.55 0.140 54.902 70 0.070 2.620

65x6 65 6 3.06 0.142 46.405 70 0.071 3.131

65x8 65 8 4.08 0.146 35.784 85 0.089 4.169

65x10 65 10 5.10 0.150 29.412 85 0.091 5.191

65x12 65 12 6.12 0.154 25.163 85 0.093 6.213

65x16 65 16 8.16 0.162 19.853 85 0.098 8.258

65x20 65 20 10.2 0.170 16.667 85 0.103 10.303

75x5 75 5 2.94 0.160 54.422 70 0.080 3.020

75x6 75 6 3.53 0.162 45.892 70 0.081 3.611

75x8 75 8 4.71 0.166 35.244 85 0.101 4.811

75x10 75 10 5.89 0.170 28.862 85 0.103 5.993

75x12 75 12 7.07 0.174 24.611 85 0.106 7.176

75x16 75 16 9.42 0.182 19.321 85 0.110 9.530

75x20 75 20 11.8 0.190 16.102 85 0.115 11.915

75x25 75 25 14.7 0.200 13.605 85 0.121 14.821

75x40 75 40 23.6 0.230 9.746 85 0.140 23.740

90x6 90 6 4.24 0.192 45.283 70 0.096 4.336

90x8 90 8 5.65 0.196 34.690 85 0.119 5.769

90x10 90 10 7.07 0.200 28.289 85 0.121 7.191

90x12 90 12 8.48 0.204 24.057 85 0.124 8.604

100x5 100 5 3.93 0.210 53.435 70 0.105 4.035

100x6 100 6 4.71 0.212 45.011 70 0.106 4.816

100x8 100 8 6.28 0.216 34.395 85 0.131 6.411



DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS


w ts ms tz mz mt


100x10 100 10 7.85 0.220 28.025 85 0.134 7.984

100x12 100 12 9.42 0.224 23.779 85 0.136 9.556

100x16 100 16 12.6 0.232 18.413 85 0.141 12.741

100x20 100 20 15.7 0.240 15.287 85 0.146 15.846

100x25 100 25 19.6 0.250 12.755 85 0.152 19.752

100x50 100 50 39.3 0.300 7.634 85 0.182 39.482

110x6 110 6 5.18 0.232 44.788 70 0.116 5.296

110x8 110 8 6.91 0.236 34.153 85 0.143 7.053

110x10 110 10 8.64 0.240 27.778 85 0.146 8.786

110x12 110 12 10.4 0.244 23.462 85 0.148 10.548

130x5 130 5 5.10 0.270 52.941 70 0.135 5.235

130x6 130 6 6.12 0.272 44.444 70 0.136 6.256

130x8 130 8 8.16 0.276 33.824 85 0.168 8.328

130x10 130 10 10.2 0.280 27.451 85 0.170 10.370

130x12 130 12 12.2 0.284 23.279 85 0.172 12.372

130x16 130 16 16.3 0.292 17.914 85 0.177 16.477

130x20 130 20 20.4 0.300 14.706 85 0.182 20.582

130x25 130 25 25.5 0.310 12.157 85 0.188 25.688

150x5 150 5 5.89 0.310 52.632 70 0.155 6.045

150x6 150 6 7.07 0.312 44.130 70 0.156 7.226

150x8 150 8 9.42 0.316 33.546 85 0.192 9.612

150x10 150 10 11.8 0.320 27.119 85 0.194 11.994

150x12 150 12 14.1 0.324 22.979 85 0.197 14.297

150x16 150 16 18.8 0.332 17.660 85 0.201 19.001

150x20 150 20 23.6 0.340 14.407 85 0.206 23.806



DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS


w ts ms tz mz mt


150x25 150 25 29.4 0.350 11.905 85 0.212 29.612

150x50 150 50 58.9 0.400 6.791 85 0.243 59.143

180x6 180 6 8.48 0.372 43.868 70 0.186 8.666

180x10 180 10 14.1 0.380 26.950 85 0.231 14.331

180x12 180 12 17.0 0.384 22.588 85 0.233 17.233

180x20 180 20 28.3 0.400 14.134 85 0.243 28.543

200x6 200 6 9.42 0.412 43.737 70 0.206 9.626

200x8 200 8 12.6 0.416 33.016 85 0.252 12.852

200x10 200 10 15.7 0.420 26.752 85 0.255 15.955

200x12 200 12 18.8 0.424 22.553 85 0.257 19.057

200x16 200 16 25.1 0.432 17.211 85 0.262 25.362

200x20 200 20 31.4 0.440 14.013 85 0.267 31.667

200x25 200 25 39.3 0.450 11.450 85 0.273 39.573

250x6 250 6 11.8 0.512 43.390 70 0.256 12.056

250x8 250 8 15.7 0.516 32.866 85 0.313 16.013

250x10 250 10 19.6 0.520 26.531 85 0.316 19.916

250x12 250 12 23.6 0.524 22.203 85 0.318 23.918

300x6 300 6 14.1 0.612 43.404 70 0.306 14.406

300x8 300 8 18.8 0.616 32.766 85 0.374 19.174

300x10 300 10 23.6 0.620 26.271 85 0.376 23.976

300x12 300 12 28.3 0.624 22.049 85 0.379 28.679



Table 7 Round Bar to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS

DIAMETER MASS THICKNESS MASS

d0 ms tz mz mt


13 Round 13 1.04 0.041 39.423 85 0.025 1.065

14 Round 14 1.21 0.044 36.364 85 0.027 1.237

15 Round 15 1.39 0.047 33.813 85 0.029 1.419

16 Round 16 1.58 0.050 31.646 85 0.030 1.610

17 Round 17 1.78 0.053 29.775 85 0.032 1.812

18 Round 18 2.00 0.057 28.500 85 0.035 2.035

19 Round 19 2.23 0.060 26.906 85 0.036 2.266

20 Round 20 2.47 0.063 25.506 85 0.038 2.508

21 Round 21 2.72 0.066 24.265 85 0.040 2.760

22 Round 22 2.98 0.069 23.154 85 0.042 3.022

24 Round 24 3.55 0.075 21.127 85 0.046 3.596

26 Round 26 4.17 0.082 19.664 85 0.050 4.220

27 Round 27 4.50 0.085 18.889 85 0.052 4.552

30 Round 30 5.55 0.094 16.937 85 0.057 5.607

32 Round 32 6.31 0.101 16.006 85 0.061 6.371

33 Round 33 6.71 0.104 15.499 85 0.063 6.773

36 Round 36 7.99 0.113 14.143 85 0.069 8.059

39 Round 39 9.38 0.123 13.113 85 0.075 9.455

42 Round 42 10.9 0.132 12.110 85 0.080 10.980

45 Round 45 12.5 0.141 11.280 85 0.086 12.586

48 Round 48 14.2 0.151 10.634 85 0.092 14.292

50 Round 50 15.4 0.157 10.195 85 0.095 15.495

56 Round 56 19.3 0.176 9.119 85 0.107 19.407

60 Round 60 22.2 0.188 8.468 85 0.114 22.314



DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS


d0 ms tz mz mt


65 Round 65 26.0 0.204 7.846 85 0.124 26.124

75 Round 75 34.7 0.236 6.801 85 0.143 34.843

80 Round 80 39.5 0.251 6.354 85 0.152 39.652

90 Round 90 49.9 0.283 5.671 85 0.172 50.072

100 Round 100 61.7 0.314 5.089 85 0.191 61.891



Table 8 Rod to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS


d0 ms tz mz mt


5.5 Rod 5.5 0.187 0.017 90.909 70 0.008 0.195

6.5 Rod 6.5 0.26 0.02 76.923 85 0.012 0.272

7 Rod 7 0.302 0.022 72.848 85 0.013 0.315

8 Rod 8 0.395 0.025 63.291 85 0.015 0.410

9 Rod 9 0.499 0.028 56.112 85 0.017 0.516

10 Rod 10 0.617 0.031 50.243 85 0.019 0.636

11.2 Rod 11.2 0.773 0.035 45.278 85 0.021 0.794

12.5 Rod 12.5 0.963 0.039 40.498 85 0.024 0.987

13 Rod 13 1.04 0.041 39.423 85 0.025 1.065

14 Rod 14 1.21 0.044 36.364 85 0.027 1.237

15 Rod 15 1.39 0.047 33.813 85 0.029 1.419

16 Rod 16 1.58 0.05 31.646 85 0.030 1.610

17 Rod 17 1.78 0.053 29.775 85 0.032 1.812

18 Rod 18 2 0.057 28.500 85 0.035 2.035



Table 9 Square Bar to AS/NZS 3679.1

DESIGNATION

STEEL

COATED AREA

COATING TOTAL MASS

SIZE MASS THICKNESS MASS

d ms tz mz mt


12 Square 12 1.13 0.048 42.478 85 0.029 1.159

16 Square 16 2.01 0.064 31.841 85 0.039 2.049

20 Square 20 3.14 0.08 25.478 85 0.049 3.189

25 Square 25 4.91 0.10 20.367 85 0.061 4.971

40 Square 40 12.6 0.16 12.698 85 0.097 12.697



Table 10 Welded Beams to AS/NZS 3679.2

DESIGNATION

STEEL

COATED AREA

COATING



tf tw ms tz mz mt


1200WB455 40 16 455 4.37 9.604 85 2.652 457.652

1200WB423 36 16 423 4.35 10.284 85 2.640 425.640

1200WB392 32 16 392 4.34 11.071 85 2.634 394.634

1200WB342 32 16 342 3.94 11.520 85 2.391 344.391

1200WB317 28 16 317 3.92 12.366 85 2.379 319.379

1200WB278 25 16 278 3.71 13.345 85 2.252 280.252

1200WB249 25 16 249 3.41 13.695 85 2.070 251.070

1000WB322 32 16 322 3.62 11.242 85 2.197 324.197

1000WB296 28 16 296 3.60 12.162 85 2.185 298.185

1000WB258 25 16 258 3.39 13.140 85 2.057 260.057

1000WB215 20 16 215 3.17 14.744 85 1.924 216.924

900WB282 32 12 282 3.42 12.128 85 2.076 284.076

900WB257 28 12 257 3.41 13.268 85 2.070 259.070

900WB218 25 12 218 3.20 14.679 85 1.942 219.942

900WB175 20 12 175 2.98 17.029 85 1.809 176.809

800WB192 28 10 192 2.81 14.635 85 1.705 193.705

800WB168 25 10 168 2.70 16.071 85 1.639 169.639

800WB146 20 10 146 2.68 18.356 85 1.626 147.626

800WB122 16 10 122 2.56 20.984 85 1.554 123.554

700WB173 28 10 173 2.51 14.509 85 1.523 174.523

700WB150 25 10 150 2.40 16.000 85 1.457 151.457

700WB130 20 10 130 2.38 18.308 85 1.444 131.444

700WB115 16 10 115 2.36 20.522 85 1.432 116.432



Table 11 Welded Columns to AS/NZS 3679.2

DESIGNATION

STEEL

COATED AREA

COATING



tf tw ms tz mz mt


500WC440 40 40 440 2.88 6.545 85 1.748 441.748

500WC414 40 32 414 2.9 7.005 85 1.760 415.760

500WC383 36 32 383 2.88 7.520 85 1.748 384.748

500WC340 32 25 340 2.98 8.765 85 1.809 341.809

500WC290 28 20 290 2.97 10.241 85 1.802 291.802

500WC267 25 20 267 2.96 11.086 85 1.796 268.796

500WC228 20 20 228 2.94 12.895 85 1.784 229.784

400WC361 40 40 361 2.38 6.593 85 1.444 362.444

400WC328 40 28 328 2.4 7.317 85 1.457 329.457

400WC303 36 28 303 2.39 7.888 85 1.450 304.450

400WC270 32 25 270 2.38 8.815 85 1.444 271.444

400WC212 25 20 212 2.36 11.132 85 1.432 213.432

400WC181 20 20 181 2.34 12.928 85 1.420 182.420

400WC144 16 16 144 2.33 16.181 85 1.414 145.414

350WC280 40 28 280 2.05 7.321 85 1.244 281.244

350WC258 36 28 258 2.04 7.907 85 1.238 259.238

350WC230 32 25 230 2.03 8.826 85 1.232 231.232

350WC197 28 20 197 2.02 10.254 85 1.226 198.226



Table 12 Circular Hollow Sections (CHS) to AS/NZS 1163

DESIGNATION

(d0 x ts)

STEEL

COATED AREA

COATING TOTAL MASS

DIAMETER THICKNESS MASS THICKNESS MASS

d0 ts ms tz mz mt


457.0x12.7 CHS 457.0 12.7 139 2.79 20.1 85 1.694 140.639

457.0x9.5 CHS 457.0 9.5 104 2.81 26.9 85 1.706 106.111

457.0x6.4 CHS 457.0 6.4 70.7 2.83 40.1 85 1.718 72.368

406.4x12.7 CHS 406.4 12.7 123 2.47 20.1 85 1.501 124.746

406.4x9.5 CHS 406.4 9.5 92.6 2.49 26.9 85 1.513 94.143

406.4x 6.4 CHS 406.4 6.4 62.8 2.51 40.0 85 1.525 64.325

355.6x12.7 CHS 355.6 12.7 107 2.15 20.2 85 1.308 108.068

355.6x9.5 CHS 355.6 9.5 80.9 2.17 26.9 85 1.320 82.175

355.6x6.4 CHS 355.6 6.4 55.0 2.19 39.9 85 1.332 56.282

323.9x12.7 CHS 323.9 12.7 97.3 1.96 20.1 85 1.187 98.527

323.9x9.5 CHS 323.9 9.5 73.0 1.98 27.1 85 1.199 74.204

323.9x6.4 CHS 323.9 6.4 49.5 1.99 40.3 85 1.211 50.666

273.1x12.7 CHS 273.1 12.7 80.9 1.64 20.2 85 0.993 81.848

273.1x9.3 CHS 273.1 9.3 60.4 1.66 27.4 85 1.006 61.451

273.1x6.4 CHS 273.1 6.4 41.6 1.68 40.3 85 1.017 42.622

273.1x4.8 CHS 273.1 4.8 31.4 1.69 53.7 70 0.843 32.243

219.1x8.2 CHS 219.1 8.2 42.4 1.33 31.3 85 0.804 43.194

219.1x6.4 CHS 219.1 6.4 33.0 1.34 40.5 85 0.811 33.781

219.1x4.8 CHS 219.1 4.8 25.1 1.35 53.6 70 0.673 25.793

168.3x7.1 CHS 168.3 7.1 27.5 1.01 36.9 85 0.615 28.090

168.3x6.4 CHS 168.3 6.4 25.1 1.02 40.5 85 0.617 25.737

168.3x4.8 CHS 168.3 4.8 18.8 1.03 54.5 70 0.513 19.353

165.1x5.4 CHS 165.1 5.4 21.2 1.00 47.3 70 0.502 21.697

165.1x5.0 CHS 165.1 5.0 19.6 1.01 51.3 70 0.503 20.128



DESIGNATION

(d0 x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d0 ts ms tz mz mt


165.1x3.5 CHS 165.1 3.5 13.3 1.02 76.1 70 0.507 13.852

139.7x5.4 CHS 139.7 5.4 17.3 0.844 48.9 70 0.422 17.692

139.7x5.0 CHS 139.7 5.0 16.5 0.846 51.3 70 0.423 16.908

139.7x3.5 CHS 139.7 3.5 11.0 0.856 77.9 70 0.428 11.418

139.7x3.0 CHS 139.7 3.0 9.42 0.859 91.2 55 0.337 9.757

114.3x5.4 CHS 114.3 5.4 14.1 0.684 48.4 70 0.342 14.472

114.3x4.5 CHS 114.3 4.5 11.8 0.690 58.6 70 0.345 12.120

114.3x3.6 CHS 114.3 3.6 9.42 0.696 73.8 70 0.348 9.768

114.3x3.2 CHS 114.3 3.2 8.64 0.698 80.8 70 0.349 8.984

101.6x5.0 CHS 101.6 5.0 11.8 0.607 51.5 70 0.303 12.078

101.6x4.0 CHS 101.6 4.0 9.42 0.613 65.1 70 0.306 9.726

101.6x3.2 CHS 101.6 3.2 7.07 0.618 87.5 70 0.309 7.374

101.6x2.6 CHS 101.6 2.6 6.28 0.622 99.1 55 0.244 6.524

88.9x5.9 CHS 88.9 5.9 11.8 0.522 44.3 70 0.261 12.036

88.9x5.0 CHS 88.9 5.0 10.2 0.527 51.7 70 0.263 10.468

88.9x4.0 CHS 88.9 4.0 7.85 0.533 68.0 70 0.267 8.117

88.9x3.2 CHS 88.9 3.2 6.28 0.538 85.7 70 0.269 6.549

88.9x2.6 CHS 88.9 2.6 5.50 0.542 98.7 55 0.213 5.708

76.1x5.9 CHS 76.1 5.9 10.2 0.441 43.2 70 0.220 10.425

76.1x4.5 CHS 76.1 4.5 7.85 0.450 57.3 70 0.225 8.075

76.1x3.6 CHS 76.1 3.6 6.28 0.456 72.5 70 0.228 6.508

76.1x3.2 CHS 76.1 3.2 5.50 0.458 83.4 70 0.229 5.724

76.1x2.3 CHS 76.1 2.3 3.93 0.464 118 55 0.182 4.107

60.3x5.4 CHS 60.3 5.4 7.07 0.345 48.8 70 0.172 7.237

60.3x4.5 CHS 60.3 4.5 5.50 0.351 63.8 70 0.175 5.670



DESIGNATION

(d0 x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d0 ts ms tz mz mt


60.3x3.6 CHS 60.3 3.6 4.71 0.356 75.6 70 0.178 4.888

60.3x2.9 CHS 60.3 2.9 3.93 0.361 91.9 55 0.142 4.067

60.3x2.3 CHS 60.3 2.3 3.14 0.364 116 55 0.143 3.283

48.3x5.4 CHS 48.3 5.4 5.50 0.270 49.1 70 0.135 5.630

48.3x4.0 CHS 48.3 4.0 3.93 0.278 70.9 70 0.139 4.064

48.3x3.2 CHS 48.3 3.2 3.14 0.283 90.2 70 0.142 3.282

48.3x2.9 CHS 48.3 2.9 3.14 0.285 90.8 55 0.112 3.252

48.3x2.3 CHS 48.3 2.3 2.36 0.289 123 55 0.114 2.469

42.4x4.0 CHS 42.4 4.0 3.14 0.241 76.8 70 0.121 3.261

42.4x3.2 CHS 42.4 3.2 2.36 0.246 105 70 0.123 2.478

42.4x2.6 CHS 42.4 2.6 2.36 0.250 106 55 0.098 2.453

42.4x2.0 CHS 42.4 2.0 1.57 0.254 162 55 0.100 1.670

33.7x4.0 CHS 33.7 4.0 2.36 0.187 79.2 70 0.093 2.448

33.7x3.2 CHS 33.7 3.2 2.36 0.192 81.4 70 0.096 2.451

33.7x2.6 CHS 33.7 2.6 1.57 0.195 124 55 0.077 1.647

33.7x2.0 CHS 33.7 2.0 0.785 0.199 254 55 0.078 0.863

26.9x3.2 CHS 26.9 3.2 1.57 0.149 94.8 70 0.074 1.644

26.9x2.6 CHS 26.9 2.6 0.785 0.153 194 55 0.060 0.845

26.9x2.3 CHS 26.9 2.3 0.785 0.155 197 55 0.061 0.846

26.9x2.0 CHS 26.9 2.0 0.785 0.156 199 55 0.061 0.846

21.3x3.2 CHS 21.3 3.2 0.785 0.114 145 70 0.057 0.842

21.3x2.6 CHS 21.3 2.6 0.785 0.117 150 55 0.046 0.831

21.3x2.0 CHS 21.3 2.0 0.785 0.121 154 55 0.048 0.833



Table 13 Rectangular Hollow Sections (RHS) to AS/NZS 1163

DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS

DEPTH WIDTH THICKNESS MASS THICKNESS MASS

d b ts ms tz mz mt

mm mm mm kg/m m2/m m2/t µm kg/m kg/m

250x150x9.0 RHS 250 150 9.0 51.8 1.47 28.3 85 0.890 52.700

250x150x6.0 RHS 250 150 6.0 35.6 1.51 42.4 70 0.755 36.394

250x150x5.0 RHS 250 150 5.0 30.0 1.53 50.9 70 0.763 30.750

200x100x9.0 RHS 200 100 9.0 37.7 1.07 28.3 85 0.647 38.327

200x100x6.0 RHS 200 100 6.0 26.2 1.11 42.4 70 0.555 26.774

200x100x5.0 RHS 200 100 5.0 22.1 1.13 50.8 70 0.563 22.700

200x100x4.0 RHS 200 100 4.0 18.0 1.14 63.4 70 0.570 18.547

150x100x9.0 RHS 150 100 9.0 30.6 0.866 28.3 85 0.526 31.141

150x100x6.0 RHS 150 100 6.0 21.5 0.911 42.3 70 0.455 21.964

150x100x5.0 RHS 150 100 5.0 18.2 0.926 50.8 70 0.463 18.675

150x100x4.0 RHS 150 100 4.0 14.8 0.941 63.4 70 0.470 15.307

150x50x6.0 RHS 150 50 6.0 16.8 0.711 42.3 70 0.355 17.154

150x50x5.0 RHS 150 50 5.0 14.3 0.726 50.8 70 0.363 14.650

150x50x4.0 RHS 150 50 4.0 11.7 0.741 63.3 70 0.370 12.067

150x50x3.0 RHS 150 50 3.0 9.0 0.761 84.2 55 0.299 9.326

150x50x2.5 RHS 150 50 2.5 7.5 0.767 102 55 0.301 7.837

150x50x2.0 RHS 150 50 2.0 6.1 0.774 126 55 0.304 6.427

125x75x6.0 RHS 125 75 6.0 16.8 0.711 42.3 70 0.355 17.154

125x75x5.0 RHS 125 75 5.0 14.3 0.726 50.8 70 0.363 14.650

125x75x4.0 RHS 125 75 4.0 11.7 0.741 63.3 70 0.370 12.067

125x75x3.0 RHS 125 75 3.0 9.0 0.761 84.2 55 0.299 9.326

125x75x2.5 RHS 125 75 2.5 7.5 0.767 102 55 0.301 7.837

125x75x2.0 RHS 125 75 2.0 6.1 0.774 126 55 0.304 6.427



DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d b ts ms tz mz mt


100x50x6.0 RHS 100 50 6.0 12.1 0.511 42.3 70 0.255 12.344

100x50x5.0 RHS 100 50 5.0 10.4 0.526 50.7 70 0.263 10.625

100x50x4.0 RHS 100 50 4.0 8.6 0.541 63.2 70 0.270 8.827

100x50x3.5 RHS 100 50 3.5 7.5 0.548 72.7 70 0.274 7.810

100x50x3.0 RHS 100 50 3.0 6.7 0.561 84.0 55 0.220 6.893

100x50x2.5 RHS 100 50 2.5 5.6 0.567 102 55 0.223 5.796

100x50x2.0 RHS 100 50 2.0 4.6 0.574 126 55 0.225 4.778

100x50x1.6 RHS 100 50 1.6 3.7 0.579 157 55 0.227 3.917

75x50x6.0 RHS 75 50 6.0 9.7 0.411 42.2 70 0.205 9.939

75x50x5.0 RHS 75 50 5.0 8.4 0.426 50.7 70 0.213 8.612

75x50x4.0 RHS 75 50 4.0 7.0 0.441 63.1 70 0.220 7.207

75x50x3.0 RHS 75 50 3.0 5.5 0.461 83.8 55 0.181 5.676

75x50x2.5 RHS 75 50 2.5 4.6 0.467 101 55 0.183 4.815

75x50x2.0 RHS 75 50 2.0 3.8 0.474 126 55 0.186 3.954

75x50x1.6 RHS 75 50 1.6 3.1 0.479 156 55 0.188 3.250

75x25x2.5 RHS 75 25 2.5 3.6 0.367 102 55 0.144 3.755

75x25x2.0 RHS 75 25 2.0 3.0 0.374 125 55 0.147 3.130

75x25x1.6 RHS 75 25 1.6 2.4 0.379 156 55 0.149 2.582

65x35x4.0 RHS 65 35 4.0 5.4 0.341 62.9 70 0.170 5.587

65x35x3.0 RHS 65 35 3.0 4.3 0.361 83.5 55 0.142 4.459

65x35x2.5 RHS 65 35 2.5 3.6 0.367 102 55 0.144 3.755

65x35x2.0 RHS 65 35 2.0 3.0 0.374 125 55 0.147 3.130

50x25x3.0 RHS 50 25 3.0 3.1 0.261 83.0 55 0.102 3.242

50x25x2.5 RHS 50 25 2.5 2.7 0.267 100 55 0.105 2.774

50x25x2.0 RHS 50 25 2.0 2.2 0.274 125 55 0.107 2.305



DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d b ts ms tz mz mt


50x25x1.6 RHS 50 25 1.6 1.8 0.279 155 55 0.110 1.915

50x20x3.0 RHS 50 20 3.0 2.9 0.241 82.8 55 0.094 2.999

50x20x2.5 RHS 50 20 2.5 2.4 0.247 102 55 0.097 2.531

50x20x2.0 RHS 50 20 2.0 2.0 0.254 124 55 0.100 2.141

50x20x1.6 RHS 50 20 1.6 1.6 0.259 157 55 0.102 1.750



Table 14 Square Hollow Sections (SHS) TO AS/NZS 1163

DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d b ts ms tz mz mt


250x250x9.0 SHS 250 250 9.0 65.9 1.87 28.3 85 1.133 67.073

250x250x6.0 SHS 250 250 6.0 45.1 1.91 42.4 70 0.955 46.014

200x200x9.0 SHS 200 200 9.0 51.8 1.47 28.3 85 0.890 52.700

200x200x6.0 SHS 200 200 6.0 35.6 1.51 42.4 70 0.755 36.394

200x200x5.0 SHS 200 200 5.0 30.0 1.53 50.9 70 0.763 30.750

150x150x9.0 SHS 150 150 9.0 37.7 1.07 28.3 85 0.647 38.327

150x150x6.0 SHS 150 150 6.0 26.2 1.11 42.4 70 0.555 26.774

150x150x5.0 SHS 150 150 5.0 22.1 1.13 50.8 70 0.563 22.700

125x125x9.0 SHS 125 125 9.0 30.6 0.866 28.3 85 0.526 31.141

125x125x6.0 SHS 125 125 6.0 21.5 0.911 42.3 70 0.455 21.964

125x125x5.0 SHS 125 125 5.0 18.2 0.926 50.8 70 0.463 18.675

125x125x4.0 SHS 125 125 4.0 14.8 0.941 63.4 70 0.470 15.307

100x100x9.0 SHS 100 100 9.0 23.6 0.666 28.3 85 0.404 23.954

100x100x6.0 SHS 100 100 6.0 16.8 0.711 42.3 70 0.355 17.154

100x100x5.0 SHS 100 100 5.0 14.3 0.726 50.8 70 0.363 14.650

100x100x4.0 SHS 100 100 4.0 11.7 0.741 63.3 70 0.370 12.067

100x100x3.0 SHS 100 100 3.0 9.0 0.761 84.2 55 0.299 9.326

100x100x2.5 SHS 100 100 2.5 7.5 0.767 102 55 0.301 7.837

100x100x2.0 SHS 100 100 2.0 6.1 0.774 126 55 0.304 6.427

89x89x6.0 SHS 89 89 6.0 14.7 0.623 42.4 70 0.311 14.991

89x89x5.0 SHS 89 89 5.0 12.6 0.638 50.8 70 0.319 12.879

89x89x3.5 SHS 89 89 3.5 9.1 0.660 72.5 70 0.330 9.436

75x75x6.0 SHS 75 75 6.0 12.1 0.511 42.3 70 0.255 12.344

75x75x5.0 SHS 75 75 5.0 10.4 0.526 50.7 70 0.263 10.625



DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d b ts ms tz mz mt


75x75x4.0 SHS 75 75 4.0 8.6 0.541 63.2 70 0.270 8.827

75x75x3.5 SHS 75 75 3.5 7.5 0.548 72.7 70 0.274 7.810

75x75x3.0 SHS 75 75 3.0 6.7 0.561 84.0 55 0.220 6.893

75x75x2.5 SHS 75 75 2.5 5.6 0.567 102 55 0.223 5.796

75x75x2.0 SHS 75 75 2.0 4.6 0.574 126 55 0.225 4.778

65x65x6.0 SHS 65 65 6.0 10.2 0.431 42.2 70 0.215 10.420

65x65x5.0 SHS 65 65 5.0 8.8 0.446 50.7 70 0.223 9.015

65x65x4.0 SHS 65 65 4.0 7.3 0.461 63.1 70 0.230 7.531

65x65x3.0 SHS 65 65 3.0 5.7 0.481 83.9 55 0.189 5.919

65x65x2.5 SHS 65 65 2.5 4.8 0.487 102 55 0.191 4.980

65x65x2.0 SHS 65 65 2.0 3.9 0.494 126 55 0.194 4.119

65x65x1.6 SHS 65 65 1.6 3.1 0.499 159 55 0.196 3.336

50x50x5.0 SHS 50 50 5.0 6.4 0.326 50.6 70 0.163 6.600

50x50x4.0 SHS 50 50 4.0 5.4 0.341 62.9 70 0.170 5.587

50x50x3.0 SHS 50 50 3.0 4.3 0.361 83.5 55 0.142 4.459

50x50x2.5 SHS 50 50 2.5 3.6 0.367 102 55 0.144 3.755

50x50x2.0 SHS 50 50 2.0 3.0 0.374 125 55 0.147 3.130

50x50x1.6 SHS 50 50 1.6 2.4 0.379 156 55 0.149 2.582

40x40x4.0 SHS 40 40 4.0 4.2 0.261 62.6 70 0.130 4.291

40x40x3.0 SHS 40 40 3.0 3.4 0.281 83.1 55 0.110 3.486

40x40x2.5 SHS 40 40 2.5 2.8 0.287 102 55 0.113 2.939

40x40x2.0 SHS 40 40 2.0 2.4 0.294 125 55 0.115 2.470

40x40x1.6 SHS 40 40 1.6 1.9 0.299 159 55 0.117 2.001

35x35x3.0 SHS 35 35 3.0 2.9 0.241 82.8 55 0.094 2.999

35x35x2.5 SHS 35 35 2.5 2.4 0.247 102 55 0.097 2.531



DESIGNATION

(d x b x ts)

STEEL

COATED AREA

COATING TOTAL MASS


d b ts ms tz mz mt


35x35x2.0 SHS 35 35 2.0 2.0 0.254 124 55 0.100 2.141

35x35x1.6 SHS 35 35 1.6 1.6 0.259 157 55 0.102 1.750

30x30x2.0 SHS 30 30 2.0 1.7 0.214 124 55 0.084 1.811

30x30x1.6 SHS 30 30 1.6 1.4 0.219 155 55 0.086 1.499

25x25x3.0 SHS 25 25 3.0 2.0 0.161 81.8 55 0.063 2.026

25x25x2.5 SHS 25 25 2.5 1.6 0.167 101 55 0.066 1.714

25x25x2.0 SHS 25 25 2.0 1.4 0.174 123 55 0.068 1.481

25x25x1.6 SHS 25 25 1.6 1.2 0.179 152 55 0.070 1.248

20x20x1.6 SHS 20 20 1.6 0.9 0.139 148 55 0.055 0.997

Advisory Note #45

Documents

Transcript of Advisory Note #45