Analysis On Surface Texturing Design for Wear Protection of ...
Advanced Ceramic Wear Plate · 2019-11-05 · • Excellent wear protection - for tough mining...
2
® ASGCO ™ X-Wear Mine Duty is made of extremely hard ceramics that provide unsurpassed resistance to abrasive wear while the rubber effectively dampens the impact forces that can crack the ceramic rods. The resilient rubber matrix that surrounds the ceramic rods is hot vulcanized for superior adhesion. 301 Gordon Street . Allentown, PA 18102 . 1-800-344-4000 . Fax: 610-778-8991 . www.asgco.com TYPICAL EXAMPLES: • Transfer points in conveyor systems • Screen chutes • Deflectors Feeders ™ R X-WEA MINE DUTY Advanced Ceramic Wear Plate 12” 12” 1¼” IMPACT RESISTANT - • ¼” Steel Backing • 1” rubber with ¾” Cylindrical Alumina Ceramic UNIQUE ZIG-ZAG PATTERN - prevents wear channeling ALSO AVAILABLE IN - Square 2¼” Ceramic • ™ Wide range of use - X-Wear Mine Duty Wear Liner is mainly used in the mining and quarrying industries, where severe abrasion occurs and the angles of impact are low. • Excellent wear protection - for tough mining conditions were there is a need for both wear protection and low noise materials. • 1/4″ steel backing - is suitable for stud welding or plug welding. • Plates are available - with factory-welded mounting studs for ease of installation. • Advanced Hard Ceramic Wear plate • Easy to install • Reduces noise • Unsurpassed impact resistance • Smooth surface • Longest Wear Life Available BENEFITS & FEATURES
Transcript of Advanced Ceramic Wear Plate · 2019-11-05 · • Excellent wear protection - for tough mining...
®
ASGCO ™X-Wear Mine Duty is made of extremely hard ceramics that provide unsurpassed resistance to abrasive wear while the rubber effectively dampens the impact forces that can crack the ceramic rods. The resilient rubber matrix that surrounds the ceramic rods is hot vulcanized for superior adhesion.
301 Gordon Street . Allentown, PA 18102 . 1-800-344-4000 . Fax: 610-778-8991 . www.asgco.com
TYPICAL EXAMPLES: • Transfer points in conveyor systems • Screen chutes • Deflectors Feeders
™R X-WEAMINE DUTY
Advanced Ceramic Wear Plate
12”
12”
1¼”
IMPACT RESISTANT -• ¼” Steel Backing• 1” rubber with ¾” Cylindrical Alumina Ceramic
UNIQUE ZIG-ZAG PATTERN - prevents wear channeling
ALSO AVAILABLE IN - Square 2¼” Ceramic
• ™ Wide range of use - X-Wear Mine Duty Wear Liner is mainly used in the mining and quarrying industries, where severe abrasion occurs and the angles of impact are low.
• Excellent wear protection - for tough mining conditions were there is a need for both wear protection and low noise materials.
• 1/4″ steel backing - is suitable for stud welding or plug welding.
• Plates are available - with factory-welded mounting studs for ease of installation.
• Advanced Hard Ceramic Wear plate
• Easy to install
• Reduces noise
• Unsurpassed impact resistance
• Smooth surface
• Longest Wear Life Available
BENEFITS & FEATURES
2’ 4’ 6’ 8’ 10’ 12’
9
8
7
6
5
4
3
2
1
0
Height of Fall
Siz
e o
f M
ater
ial (
inch
es)
IMPACT RATING
Note: This is an average for materials impacting panels at an angle of between 0-60 degrees. If materials are hitting panels at angles of between 60-90 degrees then the impact rating is half of shown chart.
Fastening Methods
Stud Welded Bolt
Plates are available with factory-welded mounting studs for ease of installation.
Coal
Hard Rock
301 Gordon Street . Allentown, PA 18102 . 1-800-344-4000 . Fax: 610-778-8991 . www.asgco.com
MDX Round 1¼” Ceramic SDX Square 2¼” Ceramic
Custom sizes available at customers request.
A
A
BB
DCDC
EE
™ X-WEAR MINE DUTY
A B C D E Ceramic Liner Wt
Part Number Width Length Thickness Thickness Total Lbs
ASG-12X12X1.25-MDX 12” 12” 1” 1/4” 1¼” 20
ASG-12X12X2.375-SDX 12” 12” 2” 3/8” 2-3/8” 40
®© 3/2017 ASGCO “Complete Conveyor Solutions”
