ADAIRINSTALLATION INSTRUCTIONS

4.2L SKIRTED CLASS FIVE+ ONE-PIECE TOILET

S-TRAP 305mm K-5171T-M/K-5171T-CMS-TRAP 400mm K-4983T-M/K-4983T-CM

4.2

�

�

�

Please read these instructions carefully to familiarizeyourself with the required tools, materials, and installationsequences. Follow the sections that pertain to yourparticular installation. This will help you avoid costlymistakes. In addition to proper installation, read alloperating and safety instructions.

All information in these instructions is based upon thelatest product information available at the time ofpublication. Kohler China reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.

These instructions contain important care, cleaning, andwarranty information -

.please leave instructions for the

consumer

�

�

� -

ORDERING INFORMATION

ADAIR 4.2L Skirted Class Five+ One-Piece Toilet

305mm ....................................................................K-5171T-M

Includes

ADAIR 4.2L Skirted Class Five+ One-Piece Toilet

305mm..................................................................K-5171T-CM

Includes

ADAIR 4.2L Skirted Class Five+ One-Piece Toilet

400mm ....................................................................K-4983T-M

Includes

ADAIR 4.2L Skirted Class Five+ One-Piece Toilet

400mm..................................................................K-4983T-CM

Includes

French Curve Toilet Seat..........................K-4653T

French Curve Quiet-close Toilet Seat ......K-4713T

French Curve Toilet Seat..........................K-4653T

French Curve Quiet-close Toilet Seat ......K-4713T

®

®

®

®

4.2

305mm....................................................................K-5171T-M

......................................

4.2

305mm .................................................................K-5171T-CM

......................................

4.2

400mm ....................................................................K-4983T-M

......................................

4.2

400mm..................................................................K-4983T-CM

......................................

K-4653T

K-4713T

K-4653T

K-4713T

NOTES

�

�

�

�

�

�

�

�

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 140mm centers.

Ensure that the new drain has the correct roughing-indimension. This toilet has a 305/400mm roughing-indimension. .

Closet flange must be 305/400mm on-center from wall.

Carefully inspect the new fixture for any sign of damage.

For new construction, refer to the dimensions infor locating the shut-off valve.

Fixture dimensions are nominal and conform to tolerancesestablished by ASME Standards (A112.19.2-2013).

See Roughing-in

installation step

� The product complies with GB 6952-2005.

�

�

�

�

�

�

�

�

140mm

305/400mm( )

305/400mm

ASME ()

A112.19.2-2013

� GB 6952-2005

-1-

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 5281372 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 2564108 256410

©

©

Copyright Kohler China Investment Co., Ltd. 2015

20151259054-T01-A

WARNING: Risk of personal injury or productdamage

WARNING: Risk of external leakage

: Handle vitreous china products very carefully.Vitreous china can break and chip if you overtightenbolts and nuts.

. The fill valvenut has been factory-tightened to design specifications.If re-tightening is required, wrench tighten one turnpast finger tight .

-2-

TOOLS AND MATERIALS REQUIRED (Not

supplied)

�

�

�

�

�

�

�

�

�

�

�

�

254mm (10") adjustable wrench

305mm (12") pipe wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Toilet gasket (wax seal)

Toilet T-bolts (2), 8mm (5/16") diameter

Toilet supply shut-off valve, 10mm(3/8 ) recommended

If the existing toilet does not have a supply shut-offvalve below the tank, install one before installing the newtoilet.

"

NOTICE:

�

�

�

�

�

�

�

�

�

�

�

�

254mm

305mm

8mm T 2

10mm

Unit: mm:

Reference Value

K-5171T-M/K-5171T-CM

645

265

FRONT OF BOWL

OF OUTLETCL305

Finished Wall

411

720

389

706Supply

160

20

0

140

1259054-T01-A

411

720

389

694Supply

160

20

0

140

-3-

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a spongeto remove the remaining water from the tank and bowl.Disconnect the supply shut-off valve (if present), and removethe old tank and bowl.

( )

Fig.#11

INSTALLATION

K-4983T-M/K-4983T-CM

Kohler reserves the right to change marked dimensions without prior notice.

Fig.#22

Remove the old gasket from the floorand the closet flange with a putty knife.Remove the old T-bolts and discardthem.

if the new toilet is notinstalled immediately, temporarily stuffa rag into the closet flange.

NOTICE:

T

NOTICE: Do not use white cement or high lime contentcements to install this toilet. The expansion of cement due toa rise in temperature may make the toilet crack or causedamage. Kohler is not responsible for any damage caused byinstallation with the use of cement.

Closet Flange

mm

67mm;

200mm

160

Fig.#33

TO INSTALL SUPPLYSHUT-OFF VALVE

Install the supply shut-off valve so it is200mm above the finished floor line,and 160mm to the left of the closetflange centerline.

The centerline of the supply shut-offvalve outlet should extend 67mm fromthe finished wall. Install the supplyshut-off valve with the outlet vertical.

Supply Shut-Off Valve

Closet FlangeCenterline

160

305/400

200

645

360

FRONT OF BOWL

OF OUTLETCL400

Finished Wall

1259054-T01-A

-4-

10mm

TO INSTALL BOWL

Position the template and align with

drain hole.

Mark down the position of foot and 5

holes.

Drill holes on ground with the drill of

10mm (3/8"), then insert anchor to

holes.

Fig.#77

Firmly press the toilet gasket onto thetoilet outlet of plastic trap.

Wax ring type toilet gasketshould not be installed at temperaturesless than 21 C.

If you are using a toiletgasket with an integral plastic sleeve,make sure the gasket is positionedwith the sleeve facing away from thetoilet.

NOTE 1:

NOTE 2:

o

1

21

2

oC

Install brackets.

Plastic Trap Outlet

Toilet Gasket

Fig.#88

Install plastic to ground and mounted

with 3 set of bolts firmly.

3

NOTE: Must use the toilet installationgasket ring (not supplied) to seal thearea where the waste pipe contactsthe construction section to avoidleakage.

(

)

Fig.#44

Fig.#55

Drain Hole

3/810mm

Fig.#66

1259054-T01-A

Fig.#99

Fig.#1010

Carefully align and lower the bowl.Apply weight to the bowl rim to let theoutlet insert into plastic trap.

Carefully thread the screws into the

brackets, until toilet is secure.

Alternately tighten left and right sides

to prevent pulling the toilet off center.

Install cap to cover screw.

Do not overtighten.

Cap ScrewBushing

Fig.#1111

Apply caulk around base.

TO CONNECT WATERSUPPLY

* Flexible hose (not provided) arerecommended to connect the supplyline to the fill valve. If you use a rigidconnection(not provided), take carenot to apply side forces to the bottomof the fill valve. Be sure the rigidconnection must be fit with supply linecompletely to prevent damage shankby forced connection.

( )

( )

Supply Shank*

Supply Shut-Off Valve

Fig.#1212

IMPORTANT:

Make certain the top is turned to the lockedposition. Valve may not turn on if top is not fully in thelocked position.

Before turning on the supply valve for the firsttime, follow the steps below to clear sand, debris and rustfrom the system:

Make sure water sure water supply is off. Remove valve ENDby rotating it 1/8 turn counterclockwise.

While holding a container over the uncapped VALVE toprevent splashing, turn water supply on and off a few times.Leave water supply off.

Replace END by engaging lugs and rotating 1/8 turnclockwise.

Turn on water supply. Check that water level is at the markedwater line.

1/8

1/8

Outlet

Plastic Trap

-5-1259054-T01-A

Install the tank lid and the seat. Use

the supplied hardware pack for seat.

Periodically check for leaks for several

days following the installation.

Fig.#1313

Fig.#1414

Fig.#15a15a

Fig.#15b15b

-6-

FILL FLOAT WITH

BALLAST

Test flush the toilet.

Periodically check all connections for

leaks for several days following

installation.

Set the tank cover in place on the tank.

MINOR ADJUSTMENT OFWATER LEVEL

Move the snap along "OPEN" direction. OPEN

To lower water level: Move water cup

down to a proper height and rotate

screw anticlockwise to achieve the

desired water level. (Refer to float

adjustment instructions.)

Screw

Snap

SCALE5:1

OPEN

CLOSE

1259054-T01-A

-7-

CLOSEFasten the snap along "CLOSE"

direction.

E G 2-4mm

Float adjustment instructions: Make

sure the height of surface E is 2-4mm

lower than surface G.

Screw

E

Float

Water CupG

To elevate water level: Rotate screwclockwise and raise float to the desiredwater level. Elevate water cup to aproper position as well. (Refer to floatadjustment instructions.)

Fig.#15c15c

Fig.#15d15d

Fig.#15e15e

SCALE5:1

OPEN

CLOSE

1259054-T01-A

-8-

SYMPTOMS CORRECTIVE ACTION

1. Poor Flush A. Adjust the tank water level to match the waterline.B. Fully open the water supply shut-off valve.C. Clear obstructions from the trapway, jet, or bowl rim holes.D. Clear obstructions from the waste line.

A. Adjust the chain for proper slack so the seal is not held off the flush valve seat.

B. Clean or replace the seal if it is worn, dirty, or misaligned with the flush valve seat, or

if the flush valve seat is damaged. Replace the flush valve seal or flush valve.

C. Clean the fill valve seat/seat washer of debris, or replace the piston/seat washer

assembly.

D. Remove the tank and tighten the flush valve nut if flush valve gasket is leaking. Do

not overtighten. If leakage continues, replace the gasket.

E. Adjust the tank water level if it is too high.

2. No Flush

IMPORTANT: Use only genuine Kohler parts as shown to avoid property damage.

4. Tank takes excessive time to fill.

5. There is excessive noise when thetank is filling.

3. The fill valve turns on/off by itselfwithout the toilet being flushed, or itruns allowing water to enter the tank.

A. Reconnect the chain to the trip lever or flush valve.

B. Adjust the chain assembly to remove excessive slack.

A. Fully open the water supply shut-off valve.B. Clean the valve inlet, valve head, or supply line. Flush the lines.

A. Partially close the water supply shut-off valve if the water pressure to the toilet is toohigh. Check the toilet performance following any such adjustment.

B. Remove dirt or obstructions from the valve head. Flush the lines.

1. A.

B.

C.

D.

A.

B.

C. /

D.

E.

2.

4.

5.

3. /

A.B.

A.

B.

A.

B.

1259054-T01-A

-9-

( )

0 Co

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes inthe toilet rim are kept clean to ensure proper bowl flushing.Toilet bowl cleaners should be used at least once a week.Use a long-handled brush to clean the rim holes, and to cleanas far into the trap as possible to prevent mineral depositsfrom forming.

Most toilet bowl cleaners are not harmful to the vitreous chinasurface of the toilet bowl. Please follow the bowl cleanermanufacturer's instructions carefully.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containingchlorine (calcium hypochlorite) can seriously damagefittings in the tank. This damage can cause leakageand property damage.

Kohler Company shall not be responsible or liable for anydamage to these tank fittings caused by the use of cleanerscontaining chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

'

Please do not use hard materials (likescouring pad) to clean product surface, especially theproduct logo.

CAUTION:

CAUTION: Don t use any cement while installing

the toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damagethe feet of the toilet. Kohler will not be responsible forany damage because of using cement.

Do not throw into the toilet what is easy to block it,such as newspaper, paper pilch, sanitary towel.Do not bump the vitreous china with great force toprevent it from damaging and leaking.

Do not use the product in the water below 0 C.o

1259054-T01-A