Accessibile Bus Stop Design Guidance
Transcript of Accessibile Bus Stop Design Guidance
MAYOR OF LONDON
Transport for London
Accessible bus stop design guidanceBus Priority Team technical advice note BP1/06January 2006
Accessible bus stop design guidance
Further information For further details or advice on the design of accessible bus stops, contact:
Bus Priority TeamTransport for LondonWindsor House, 42-50 Victoria StreetLondon, SW1H 0TLTel 0845 300 7000
Website: www.tfl.gov.uk
Transport for London | 1
Contents1. Introduction...................................................................................................................22. Fully accessible bus services..........................................................................................43. Bus stop locations.........................................................................................................94. Passenger waiting area .................................................................................................155. Bus stop area...............................................................................................................236. Bus stop layouts ..........................................................................................................247. Bus boarders................................................................................................................318. Bus bays ......................................................................................................................399. Kerb profiles and heights .............................................................................................4310. Implementing bus stop improvements ........................................................................4611. Longer term issues ......................................................................................................4912. Bibliography .................................................................................................................50List of figuresFigure 1: Features of the bus stop environment....................................................................3Figure 2: Passenger groups benefiting from low floor buses .................................................4Figure 3: Bus stop layout objectives .....................................................................................6Figure 4: Relationships between bus and kerb ......................................................................7Figure 5: Considerations for bus stop locations....................................................................9Figure 6: Bus arrival patterns...............................................................................................11Figure 7: Bus stop location in vicinity of traffic signals fitted with SVD...............................13Figure 8: Boarding and alighting zones.................................................................................17Figure 9: Boarding and alighting zones – Alternative shelter arrangement ...........................18Figure 10: Passenger waiting area critical dimensions............................................................19Figure 11: Kerbside stop with parking on approach and exit..................................................26Figure 12: Exit side of pedestrian crossing ............................................................................27Figure 13: Exit side of junction .............................................................................................28Figure 14: Full width boarder ................................................................................................32Figure 15: Alternative full width boarder layouts...................................................................33Figure 16: Multiple bus full width boarders...........................................................................34Figure 17: Half width boarder ...............................................................................................37Figure 18: Angled boarders ...................................................................................................38Figure 19: Bus bay arrangements ..........................................................................................41Figure 20: Amendment to existing bus bay ...........................................................................42Figure 21: ‘Special’ kerbs ......................................................................................................45Figure 22: Flow chart of potential tasks for improving bus stops ..........................................47Figure 23: Gantt chart of standard tasks for improving bus stops .........................................48Figure 24: Bus dimensions ....................................................................................................52AppendicesAppendix A: Bus measurements...........................................................................................51Appendix B: Effects of introducing bus boarders ..................................................................54Appendix C: Effects of removing bus lay-bys .......................................................................56Appendix D: ‘Special’ kerbs...................................................................................................58Appendix E: Worked examples .............................................................................................59
2
Accessible bus stop design guidance
1. Introduction
This guide updates the ‘Bus Stop Layouts forLow Floor Bus Accessibility’ published in June2000 and its predecessor documents. It alsoincorporates advice developed for theintroduction of articulated buses, published byTransport for London (TfL) in April 2002. Theseupdated guidelines have been developed in thecontext of the Government's policies onintegrated transport, the Mayor’s TransportStrategy, and the Disability Discrimination Act 1995.
It is intended that this guide will assist highwayauthorities in the development of practical andaffordable measures to improve accessibility atbus stops. The measures should becompatible with the particular characteristicsof buses deployed on London’s road network.
The introduction of low floor busesthroughout London, fitted with ramps forwheelchair users, has led to a requirement forappropriate kerbside access at bus stops.Unless all stops along a bus route are equallyaccessible, passengers may be unable to boardor alight a bus at their desired location and thepotential benefits from low floor buses will bereduced. This hinders the development of aninclusive public transport system.
Bus stop design and location is recognised as acrucial element in the drive to improve thequality of bus services. The concept of 'TotalJourney Quality' recognises that bus passengersare also pedestrians at each end of the bus tripand requires that all aspects of the journey areconsidered. The convenience and comfort ofbus stops must not be overlooked.
It is important to view the bus stop as aninterchange, rather than simply a location along a bus route where buses stop,comprising only a post with a flag, and a cagelaid on the road surface.
The bus stop environment contains a numberof features that need to be considered, asillustrated in Figure 1.
A fully accessible bus service is a criticalelement in delivering a fully inclusive society.Bus stops are a vital link in this vision. TfLwishes to highlight this, and part of therationale in revising the bus stop designguidelines is to reiterate the wider issuesrelating to equality and inclusion. Furthermore,it should be remembered that kerbsidecontrols and bus boarders are merely tools –the objective is to ensure that the bus stop isfully accessible.
Transport for London | 3
Additionally, it is important to emphasise theneed for:
● training for bus drivers on how to approachand correctly use the bus stop;
● planners and engineers to optimise thelocation, design and construction of busstops; and
● motorists and enforcement authorities torecognise the necessity for bus stops to bekept clear of parked vehicles.
When reviewing individual bus stops, and theirimmediate environs, designers need to takeaccount of the wide range of issues that are
discussed within this guide. Whilst theseguidelines provide assistance with the decisionmaking process, it should be recognised thateach site is a unique location, with differentcharacteristics to be taken into account.
Bus stopenvironment
Security,including lighting
Conveniencefor passengers
Connectivitywith footways
Approach and exitpaths for buses
Space forstraightening
Posting andnumber of berths
Adequacyof platform
(waiting area)
Type andheight of kerb
TicketmachinesPedestrian
footway
DrainageInformation(includingmaps etc.)
Position of utilities'access covers and
street furniture
Bus passengershelter and seating
Surface markingsfor buses
and passengers
Bus stoppost and flag
Figure 1: Features of the bus stop environment
4
Accessible bus stop design guidance
2. Fully accessible bus services
Low floor bus usersLow floor buses reduce the height differentialbetween the kerb and bus floor. Whilst theyare generally seen as a means of improvingaccessibility for passengers with disabilities,including wheelchair users, all passengersbenefit from low floor bus services, asillustrated in Figure 2.
Research conducted by Transport ResearchLaboratory (TRL Report 271) has shown thatpassengers with pushchairs benefit greatlyfrom the introduction of low floor buses.Thus, when designing bus stops for low floorbus access, the needs of all passengers shouldbe considered, not just wheelchair users.
Features of London’s bus servicesThe entire TfL bus network is now operatedusing low floor vehicles, which have a singlestep entry, a low floor in the front part of thevehicle, and either a sloping gangway, or steptowards the rear, over the drive axle. Generally,they have front doors for boarding passengersand centre doors for those alighting.
Low floorbus accessbenefits:
People withyoung children
People withpushchairs
Ambulantdisabledpeople
People withimpaired vision
Wheelchairusers
Passengers withshopping or luggage
Elderly people
Figure 2: Passenger groups benefiting from low floor buses
Transport for London | 5
Powered ramps are usually fitted at the centredoor where wheelchair users may board andalight. Push buttons are provided forwheelchair users to alert the driver when theramp needs to be deployed. Additionally, lowfloor buses are provided with the means oflowering, or ‘kneeling’ the bus suspension toreduce the step height at stops.
In London, there are a number of busconfigurations in operation, which need to beconsidered. Flexibility should be provided indesigns in recognition that bus types using astop may change as a result of service changes.For example, articulated bus operation hasbeen introduced on several high volumeservices and passengers are able to board andalight through all three sets of doors.
The images below show typical busconfigurations currently operating on London’sroads. Appendix A provides details anddimensions of the ‘standard’ rigid andarticulated buses used to develop the layoutsin this document.
Midi bus Single deck bus
Double deck bus Articulated bus
6
Accessible bus stop design guidance
Bus stoplayout
objectives
Allow easyunobstructed
access to and fromthe stop
Minimise timespent at the busstop by the bus
Prevent/dissuadeother vehicles from
parking in the stop area
Allow the busto line up within
50mm of and parallelwith the kerb
Minimise useof kerb space wherethere are competing
demands for frontageaccess
Affordable andcommensurate with the
accessibility benefit
Remove streetfurniture which prevents
passengers boardingand alighting
Bus stop layout objectives
The ideal bus stop layout will achieve theobjectives shown in Figure 3. The bus shouldstop parallel to, and as close to the kerb aspossible to allow effective use of the bus’facilities. The critical dimensions (see Figure4.1) to consider are the vertical gap, or stepheight, from the kerb to the bus floor and thehorizontal gap from the kerb edge to the sideof the bus. A well designed bus stop willprovide features which co-ordinate with thefacilities of the low floor bus and minimisethese two distances.
The size of the vertical gap between the kerband floor of the bus will affect the gradient ofthe ramp when it is deployed (see Figure 4.2).If this gradient is too severe, some wheelchairusers may be unable to enter or exit safelyfrom the bus. Regulations under the DisabilityDiscrimination Act 1995 (DDA) require newbuses to be capable of deploying a ramp,giving a 1:8 or 12 percent (7 degree gradient),onto a kerb of at least 125mm in height. This regulation, therefore, assumes a'standard' kerb height of 125mm, which,although not the case universally, is the heightthat vehicle manufacturers are guided to applyin bus design.
Figure 3: Bus stop layout objectives
Transport for London | 7
Figure 4: Relationships between bus and kerb
Figure 4.1: Critical dimensions
Figure 4.2: Ramp gradient
Figure 4.3: Normal step height
Figure 4.4: ‘Kneeling’ step height
It is important to recognise that, even when deployed on a 125mm high kerb, thegradient of the ramp may vary. The majordeterminants include:
● type of ramp;
● ramp length;
● carriageway and footway crossfalls;
● distance of the bus from the kerb;
● ‘kneeling’ height of the bus floor (seeFigures 4.3 & 4.4); and
● whether the bus is laden.
The use of a 140mm maximum kerb height, or higher ‘special’ kerbs (see Chapter 9), arepreferred as they result in lower ramp gradients.
Bus Floor
Kerb
New stepheight
Reduction from originalstep height
Road Level
Bus Floor
Kerb
StepHeight
Road Level
Bus Floor
Ramp
Ramp Gradient
KerbRoad Level
Bus Floor
Kerb
VerticalGap
HorizontalGapKerb
Height
Road Level
8
Accessible bus stop design guidance
It should be noted that with the ‘kneeling’systems in common use, the reduction in stepheight achieved is not necessarily uniform alongthe side of the bus. The front door will be lowerthan the centre door if the ‘kneeling’ systemoperates on the front axle alone. Alternativeconfigurations include tilting of the nearside ofthe bus and lowering of the entire vehicle.
In the urban environment, there often exists aconflict between the demands for frontageservicing, short term parking and the need toprotect a sufficient length of kerb space toallow buses to easily access a stop. As withprevious guidelines, this document recognisesthe competing demands in London's busystreet environment and, therefore, retains theprevious target benchmark of the bus stoppingwithin 200mm of the kerb.
Transport for London | 9
3. Bus stop locations
IntroductionBus stops must be located to allow passengersto board and alight safely and conveniently.Ideally, they should also be situated nearplaces of particular need, such as local shops,libraries, clubs, health facilities and sheltered
housing. Stop locations are determined byLondon Buses in consultation with highwayauthorities and the police. Residents, localbusinesses and bus user groups may also needto be consulted by the highway authorityand/or London Buses.
Key considerations for bus stop locations areshown in Figure 5.
Bus stop location
Driver andprospective passengers
are clearly visible toeach other
Where there is adequate footway
width
Away from siteslikely to beobstructed
Close to (on theexit side of)pedestriancrossings
'Tail to tail' on opposite sides
of the road
Where there is space for a bus shelter
Sited to minimisewalking distance between
interchange stops
Close to main junctions without affecting
road safety or junctionoperation
Figure 5: Considerations for bus stop locations
10
Accessible bus stop design guidance
Consideration should be given to the routestaken by passengers to and from the bus stop.Locating stops near pedestrian crossingfacilities, and in particular at junctions, isconvenient and helps passengers complete therest of their journey safely. There is little pointin making a bus stop accessible to wheelchairs(and pushchairs) without also considering theaccessibility of routes to and from the bus stop.
It may also be necessary to provide additionaldropped kerb crossings and/or crossing facilitiesin the vicinity of the stop as part of any busstop improvements. Accessibility should beconsidered in terms of the whole journey.
Stop spacingAn ideal spacing for bus stops is approximately400m, although a closer spacing in towncentres and residential areas may be necessaryto meet passenger requirements.Consideration should be given to improvingspacing, and reviewing locations, particularlywhere interchange is an issue. Bus journeytimes are affected by the number of stops on
a route and therefore a careful balance mustbe achieved. If it is proposed to relocate orremove a stop, an assessment of resultingbenefits/impacts should be undertakenalongside consultation with stakeholders.
It is recommended that where locations areserved by more than 25 buses per hour (bph),bus stops should be split. This enables buseson different routes to serve separate stops,thus reducing bus-on-bus delay and trafficcongestion. However, bus routes withcommon destinations should share the same stop.
Stop capacityPrevious guidelines have highlighted the needto increase cage sizes, but omitted to stressthe related impact of high bus frequencies atstops. For example, a 37m kerbside bus stopcage is normally sufficient for a frequency of15 bph but inadequate for 45 bph, wherespace should be provided for more than onebus to access and serve the stop at the same time.
Bus stop on a high frequency corridor
Transport for London | 11
The ‘clock-face’ diagram (see Figure 6)indicates how the frequency of servicesinfluences the amount of space required at astop. Consideration also needs to be given toaverage boarding/alighting times.
Scenario C shows that, with just 26 buses perhour, the arrival pattern can result in a numberof occassions when two or three buses servethe stop at the same time.
Service 1 - Bus every 5 minutes (12 bph)
Assume start arrivals is at 12 o'clock
Total = 26 bph
Service 2 - Bus every 10 minutes (6 bph)
Service 3 - Bus every 7.5 minutes (8 bph)
Scenario B - 2 buses at the stop 6 times an hour
Scenario A - 1 bus at the stop every 5 mins
Scenario C - 2 buses at the stop 6 times an hour - 3 buses at the stop 2 times an hour
5
1050
40 20
2530
0
45 15
35
55 5
1050
40 20
2530
0
45 15
35
55
5
1050
40 20
2530
0
45 15
35
55 5
1050
40 20
2530
0
45 15
35
55
A
CB
Figure 6: Bus arrival patterns
12
Accessible bus stop design guidance
It is recognised that at certain locations thenumber and frequency of bus services may beparticularly high and compromises may have tobe made to the length of the cage. At present,approximately 7% of passengers purchase theirtickets on bus, and this number is reducing asmore people use Oyster pre-pay. The Mayorhas indicated a wish to move towards total‘cashless’ bus operation and consequently, it is expected that dwell times will reduce,bringing improvements to both bus servicesand operations.
Bus stops and traffic signalsWhere bus stops are located on the approach totraffic signalled junctions, they should not bepositioned between a bus priority detector andthe stop line. This is to avoid the signal giving
priority to the bus while it is setting down /picking up passengers.
Bus priority detectors are typically placedapproximately 80m (or 10-15 seconds busjourney time) in advance of the stop line,whilst passengers often prefer the bus stop tobe as close to the junction as possible. Ideally,bus stops should be located on the exit sideof junctions, where the effect on saturationflows is generally less than stops sited inadvance of signals (see Figure 7).
If there are proposed changes in kerb alignment(e.g. bus boarders) or traffic lanes are to berealigned, existing loops (SCOOT, MOVA or X, Yand Z loops) on the approach to junctions mayneed to be re-cut or repositioned.
Selective Vehicle Detection (SVD) beacon
Transport for London | 13
Option 2: Bus stop location before detection beacon
Detection BeaconDetection beacon 10 - 15 secsbus journey time from stop line
Bus Stop Flag
Bus Stop Flag
Bus Stop Flag
Option 1: Bus stop on exit side of junction
SHELTER
SHELTERSHELTER
Figure 7: Bus stop location in vicinity of traffic signals fitted with SVD
14
Accessible bus stop design guidance
‘Hail & Ride’
‘Hail & Ride’ has been in operation for manyyears and is often a feature of new routesand/or those serving residential areas. It canassist elderly and disabled people by reducingthe walking distance to the boarding point.However, it is difficult to guarantee closekerbside access as the driver can stop atalmost any safe location along a ‘Hail & Ride’ route.
Outlined below are options to improveaccessibility of ‘Hail & Ride’ bus services.
Option 1 – Conversion to fixed stop
On some services there may be a strong casefor conversion to fixed stops; for example,where services have grown in patronage andbuses are making frequent stops, or wherepassenger demand is concentrated atidentifiable points. Passenger surveys willassist in determining the appropriate solution.
Option 2 – Retention of ‘Hail & Ride’ sectionsof route
It may be appropriate to retain ‘Hail & Ride’operation:
● on lightly used services;
● on routes where passenger demand is veryscattered; or
● where local conditions make installation ofbus stops difficult or sensitive.
Where ‘Hail & Ride’ is retained the followingoptions should be considered to provideimproved accessibility.
Option 2a - Provision of information forpassengers where ‘Hail & Ride’ sections arealready accessible
Information posts, which display a bustimetable and other information, can beprovided at locations which offer goodaccessibility to and from buses. However,these posts are not fixed bus stops, they donot have a bus stop flag and buses can stillstop at other safe points.
The benefits of information points are thatthey provide reassurance to passengers thatbuses serve the route and they offer a sourceof information, such as the destination ofbuses. The posts also encourage passengers tocongregate, rather than waiting at shortdistances from each other and expecting thebus to make several stops. The advantage fordisabled people is that the benefits of ‘Hail & Ride’ are retained.
Option 2b - Provision of accessible pointsalong ‘Hail & Ride’ sections of route
It may be appropriate to install accessibleboarding and alighting points at intervals along‘Hail & Ride’ sections of route. Accessiblepoints could, for example, consist of a simple(2m wide x 4m long) bus boarder to providefull accessibility whilst minimising the impacton the local environment. Parking restrictionsfor accessible points without bus stops wouldrequire a Traffic Regulation Order, as bus stopclearways cannot be installed without a busstop flag.
Information posts could also be provided,where appropriate, to explain to passengersthat a section of route is ‘Hail & Ride’.
Transport for London | 15
4. Passenger waiting area
Bus stop post and flagWhen the features of the buses using a stopare known, consideration should be given tothe passenger waiting area. Ideally the layoutof the passenger waiting area should be basedaround the position of the bus stop flag. The flag indicates to passengers where theyshould wait. It also serves as a marker todrivers to indicate where the bus should bepositioned at the stop. These guidelines arebased on the bus stopping with the rear of thefront doors in line with the flag and passengersboarding from the downstream side of theflag, as shown below.
In some circumstances it may be appropriateto mount the bus stop flag on a street lightingcolumn, but this should be agreed betweenLondon Buses and the owner of the lightingcolumn. This arrangement can causedifficulties in attaching timetable cases in sucha way that they do not obstruct the column’saccess cover.
London Buses currently has a rollingprogramme to introduce solar poweredilluminated bus stop flags and timetables inthe Greater London boroughs. These solarpowered installations are not compatible withbus stop flags mounted on lighting columns.
Solar powered illuminated bus stop flag
Correct stopping position relative to bus stop flag
16
Accessible bus stop design guidance
Waiting area layoutBuses in London are usually configured with apowered ramp at the centre door. On shorterbuses, without a centre door, the ramp issituated at the front door. Sufficientunobstructed space is required at the frontand centre doors for the ramp to be deployed.Thus, on the footway where the stop islocated, there are areas which must be keptclear of all obstructions such as litter bins,telephone boxes and sign posts. The length ofclear footway required is defined by the widthof the doors. The width of footway needed isdefined by the space required for a wheelchairor pushchair to manoeuvre. The Departmentfor Transport’s Inclusive Mobility Guidelinesstate that a skilled manual wheelchair usershould be able to complete a 360° turn in aspace of 1500mm x 1500mm.
Figures 8 and 9 show suggested bus stoplayouts with boarding/alighting zones, whichmust be kept free of all street furniture.However, for simplicity, it is recommendedthat, where possible, street furniture is notpositioned throughout the length of footwaywhere boarding and alighting is expected.Additionally, street furniture located in thewaiting area can reduce the available waitingspace close to the stop. It is recommendedthat the footway, between the flag and 20mupstream, is kept clear of unnecessary street furniture.
It is also important that the stepping height isminimised along the length of the stop.Dropped kerbs for driveways pose particularproblems. Where there is a series of droppedkerbs it will be necessary to position the flagcarefully between the dropped kerbs. By adopting a boarding/alighting zone,problems for ramp deployment and steppingto and from the bus can be minimised.
At stops to be used simultaneously bymultiple vehicles the same boarding/alightingzone principle should be adopted. It is moredifficult to recommend a standard design for asecond bus because of the possible variationsin stopping position and vehicle type.Consideration needs to be given to thedistance between the rear of the first bus andthe front of the second. To allow followingbuses sufficient space to exit a stopindependently and so reduce potential delays,it is recommended that cage lengths allow a9m (7m absolute minimum) gap betweenstopped vehicles, in addition to the approach,straightening and exit length for two vehicles.
Undesirable street ‘clutter’ at bus stop
Transport for London | 17
Figure 8.1 : Rigid Bus
Figure 8.2 : Articulated Bus
Boarding / Alighting Zones
2.0m
18m
3.0m4.0m 4.0m
Bus Stop Flag
FrontDoor
CentreDoor
RearDoor
2.0m
2.0m
2.0m
4.0m
Bus Stop Flag
SHELTER
SHELTER
FrontDoor
CentreDoor
2.0m
2.0m
12m
Figure 8: Boarding and alighting zones
18
Accessible bus stop design guidance
Bus Stop Flag 2.0m
2.0m2.0m
4.0m
FrontDoor
CentreDoor
Passenger shelterwith half-end panels
12m
Bus Stop Flag2.0m
2.0m2.0m
4.0m 4.0m
3.0m
FrontDoor
CentreDoor
RearDoor
Passenger shelterwith half-end panels
18m
2.0m
Minimum footway width
Minimum footway width
2.0m
Boarding / Alighting Zones
Figure 9.2 : Articulated Bus
Figure 9.1 : Rigid Bus
Figure 9: Boarding and alighting zones – Alternative shelter arrangement
Bus passenger shelter
Figure 10 illustrates three general layouts forthe bus passenger shelter. The ‘centre offootway’ layout (see Figure 10.1) enablespassengers to shelter, see approaching buses,and then board with ease. In addition, thislayout allows wheelchair users who may wishto wait by their boarding position at the centredoors to be protected from the weather.Where articulated buses operate a three doorboarding configuration, this layout helps tospread boarders between the doors.
‘Centre of footway’ shelter layout
Other arrangements may be used wherefootways are narrow or other site constraintsdictate. The ‘back to kerb’ layout (see Figure 10.2)can encourage passengers to stand upstream ofthe shelter so that they can see and board thebus more easily. The ‘back of footway’ option(see Figure 10.3) is only appropriate where accessto adjoining buildings can be maintained.
All layouts position the bus stop flag 2mdistant from one end of the bus shelter. This arrangement provides two points ofreference for bus drivers pulling up to the kerb,and indicates to passengers where the frontdoors will open.
The design of the shelter may affect itspositioning on the site. Shelters with a halfwidth or no end panel on the bus approachside are recommended, because this improves visibility.
Transport for London | 19
BUS
STOP
Half width end panel
Bus stop flag
SHELTER
Frontage
Rec
omm
ende
d di
men
sion
s
Min
imum
dim
ensi
ons
2m
3–5m
3m
2m2.
7m
BUS
STOP
Half width or no end panel
Bus stop flag
*Above 2.7m, recommend 'centre of footway' solution
Frontage
2m
2m
2–2.
7m*
2m2m
Rec
omm
ende
ddi
men
sion
s
Min
imum
dim
ensi
ons
SHELTER
Figure 10: Passenger waiting area criticaldimensions
BUS
STOP
Half width end panel
Bus stop flag
Min
imum
dim
ensi
ons
Rec
omm
ende
ddi
men
sion
s
Grass verge of blank wall
2m
1.3m
2m
1.3–
1.5m
3m
SHELTER
Figure 10.1: Centre of footway
Figure 10.2: Back to kerb
Figure 10.3: Back of footway
20
Accessible bus stop design guidance
Shelters generally consist of between 1 and 4panels each of 1.3m in length, with end panelsof either 1.3m (full width) or 0.65m (halfwidth). Roof overhangs can affect overallshelter positioning, but narrower variants arealso available and London Buses will advise onthese issues. Lighting within the shelter canhelp to improve perception of personal safety.Other shelters, such as the ‘Landmark’ (seephoto) are also provided at selected locations.
‘Landmark’ type shelter
Footway width and pedestrian flows
The passenger waiting area, or platform, wherebus passengers board and alight needs to bedesigned to allow sufficient space for the stopinfrastructure, such as shelters, as well aspedestrian through movements. Research has
shown that pedestrians will generally cope wellwith congested conditions, but some simpleinterventions can make the pedestrianenvironment more comfortable. At somelocations it may be necessary to widen thefootway and this can often be achievedthrough the provision of a bus boarder (see Chapter 7).
Figure 10.1 shows that the ‘centre of footway’shelter layout should leave at least 2.7m (3m ispreferred) between the kerb edge and the rearof the shelter for wheelchair users tomanoeuvre. The gap between the shelter andthe rear of the footway should allow forpassengers’ tendency to stand at the rear ofthe footway in congested conditions, as well asan unobstructed width of at least 2m.Therefore, a footway width of 3-5m isrecommended (depending on pedestrian flows).
‘Back to kerb’ and ‘back of footway’ layoutsalso need to leave an unobstructed width of atleast 2m for pedestrians. Larger unobstructedwidths are recommended, but whereunobstructed widths of over 3m can beachieved, a ‘centre of footway’ shelter solutionshould be considered instead. ‘Back offootway’ layouts with large footway widths willmake it difficult to board the bus.
Footway widths are effectively reduced bystreet furniture such as telephone boxes, lampcolumns, litter bins and ticket machines. At congested bus stops, queues can oftenreach 20m upstream of the bus stop flag, andtherefore, unobstructed areas should becreated within this entire zone where possible,by moving street furniture downstream of thebus stop, rationalising it or removing italtogether. This will help visibility ofapproaching buses as well as increasing
Transport for London | 21
pedestrian space. A simple audit of features inand around bus stops should aim to:
● reduce street clutter;
● optimise bus stop location, including spacing;
● optimise shelter location; and
● consider other boundary effects, such ascash machines.
When designing accessible bus stops for aretail area, or other locations where pedestrianflows are high, pedestrian counts should beundertaken at peak times such as Saturday10am to 5pm and/or 12pm to 2pm during theworking week.
A yellow footway guidance line or edgemarking, offset 450mm from the kerb edgeand 100mm in width can be used in the busstop area. This can aid drivers, as a referencepoint, on their approach to the stops, and canencourage pedestrians to stand away from thekerb edge.
Yellow footway guidance line
Ticket machinesBus services in London are moving towards‘cashless’ boarding. In Central London, and onarticulated bus routes, tickets must be boughtbefore boarding. This has led to theinstallation of ticket machines at all stopswhere ‘cashless’ boarding has beenintroduced. The positioning of a ticketmachine at a stop depends upon the type andlocation of the shelter. However, it isimportant that ticket machines are treated thesame as other street furniture and are notlocated in the boarding and alighting zonesshown in Figure 9.
Conveniently located ticket machine
Whilst it is planned that all of London’s busservices will become ‘cashless’, it is expectedthat there will only be a very limited number ofnew ticket machines required on street. Theemphasis will be on bus passes and pre-paidOyster cards.
Waiting area environmentDesigners should consider other aspects of thepassenger waiting area, not just those primarilyrelated to access between the footway andbus. The environment of the passenger waitingarea is an important component of passengers'
22
Accessible bus stop design guidance
perceptions of the quality of the bus service and safety. A number of issues shouldbe considered:
● Street lighting: Poor, or inadequate, streetlighting can contribute to issues of personalsecurity. Good levels of illumination shouldbe provided at bus stops.
● Litter: A clean passenger waiting areaimproves the passengers' environment. Litterbins should be provided but care needs tobe taken in locating litter bins to reducenuisance, such as smells and flies, and avoidobstruction to pedestrian and passengermovement. They should also be emptiedregularly by the local authority.
● Statutory undertakers' equipment:Positioning of bus stop posts and passengershelters can be affected by undergroundutilities. Service covers can also create long
term problems at the bus stop owing toaccess requirements to equipment.Consideration should be given to theboarding/alighting zone to avoid accessdifficulties during maintenance works.
● Drainage: Poor drainage, resulting in water‘ponding’ on the footway around thepassenger waiting area or at the carriagewaykerbside, can affect the passengerenvironment. Ponding may result from poordrainage, defective carriageway repairs,rutting or blocked drains. In freezingconditions footway ponding can beparticularly dangerous. Ponding at thekerbside can result in passengers beingsplashed by passing traffic (or the bus) andit is, therefore, important that gooddrainage is provided.
Transport for London | 23
5. Bus stop area
Bus stop cageThe bus stop marking on the carriageway,often referred to as the bus 'cage', (TrafficSigns Regulations and General Directions(TSRGD) 2002 diagram 1025.1), is used todefine the limits of the bus stop. The purposeof the bus stop cage should not merely beseen as identifying a stopping point. The busstop cage has four distinct and importantobjectives – it defines an unobstructed area ofthe carriageway where the bus can:
● approach;
● straighten up;
● stop; and
● exit.
It is a key requirement that a bus stop cagemarking is provided and the area defined by thecage is unobstructed to allow easy entry and exitfor the bus and thus, improved ride quality forpassengers. The aim is that buses can pull upto within a maximum of 200mm from the kerb.Layouts to achieve this are illustrated in Chapters6 - 8. Other features that assist bus stopoperations are parking/loading restrictions andcoloured surfacing. The length of the bus stopcage will vary depending on the highway layoutand number of buses per hour using the stop.
Bus stop cages are usually 3m wide, however,designers should be aware that the TSRGD2002 does allow some variation in roadmarkings (TSRGD 2002, Article 12 Table 2). The marking can be reduced/increased by upto 10%. This allows cage widths of 2.7m to beintroduced. Experience has shown this can beuseful where carriageway widths are reduced,and there is some evidence to suggest thatnarrower 2.7m wide cages encourage busdrivers to stop closer to the kerb.
Bus stop clearwaysWithin the cage area, stopping by vehiclesother than buses is prohibited. On boroughroads a clearway marking must be provided inaccordance with TSRGD diagrams 974 and1025.1. Traffic Regulation Orders are no longerrequired for these bus stop clearways,although highway authorities may still wish toundertake public consultation.
Bus stops located on the Transport for London Road Network (TLRN), are generallymarked with double red lines. Department forTransport sign approval has recently been givenfor a wide red clearway line, which additionallyprohibits taxis and Blue Badge Holders fromstopping at bus stops on the TLRN. It isenvisaged that this restriction will only be usedat a number of strategic bus stops.
Clearway marking – Borough controlled road
Red coloured surfacingHighlighting the bus stop cage to indicate toother road users that it is an area for use bybuses is recommended. This can be achievedby providing a red coloured surface treatmentwithin the cage, either through a colouredsurface dressing or a coloured bituminoussurface course. This has proved effective indeterring illegal parking and reducingenforcement problems.
24
Accessible bus stop design guidance
6. Bus stop layouts
IntroductionBus stops unobstructed by kerbside activityare rare and it is usually necessary to find ameans to sufficiently encourage motorists tokeep the bus stop clear. As discussed inChapter 5, all bus stops should have a marked cage as per TSRGD 2002 diagram1025.1 with stopping restrictions ideallyoperating 24 hours a day.
Figure 11 (see page 26) shows layouts for both12m rigid buses and 18m articulated buseswhere the bus stop has parking bays on boththe approach and exit sides of the stop. The clear kerbside space is required to allowconvenient and efficient bus access to within200mm of the kerbside. These lengths areoften difficult to achieve, even for 12m buses,and reductions to 25m lengths have been used.Such short cage lengths do not work; anabsolute minimum length is 33m, which itselfimposes a constraint on the bus drivers' egressfrom the stop.
The cage length required will also depend onthe width of parking/loading boxes on theapproaches/exits. Where wider loading boxesare situated on the approach/exit thenadditional space is required because of theincreased lateral movement.
There is a need for alternative layouts thatreduce the length of cage required, whilstkeeping the bus stop unobstructed. There aretwo convenient locations for bus stops wherethis can be achieved:
● the exit side of a pedestrian crossing (Figure 12 on page 27); and
● the exit side of a junction (Figure 13 onpage 28).
Transport for London | 25
These two layouts assist bus access whilstminimising the length of bus stop clearway.They also have the advantage of placing stopsnear to where passengers may wish to crossthe road. Safety issues must always beconsidered when adopting such designs. It is important to plan the cage size for thefrequency of buses, otherwise following busescould block the crossing or side road (seeChapter 3 for further information).
It should be noted that buses are permitted tostop on the exit side zig-zag markings atPelican and Zebra crossings to pick up or dropoff passengers. Whilst some authorities reducethe length of exit side zig-zag markings, thispractice is not recommended.
Most junctions on bus routes have somekerbside controls. However, problems canoccur as a result of vehicles stopping betweenthe cage and junction, even with kerbsiderestrictions. In practice, marked bus cages withstopping restrictions are more effective atdiscouraging vehicles stopping in this area andare easier to implement. An extension to thecage to prohibit stopping on the approach isshown in Figure 13 (see page 28).
Any relocation of the stopping position of thebus closer to the junction should have regardto visibility for drivers of vehicles leaving theside road. While a bus using the stop is atemporary obstruction, the bus stop post/flag,passenger shelter and waiting passengersshould not unduly obscure sight lines.
Exit side of pedestrian crossing
Exit side of junction
26
Accessible bus stop design guidance
Overall length 37m
Overall length 49m
Exit taper 9m Entry taper 13m
Bus Stop Flag
Bus Stop Flag
Straightening distance 15m
Exit taper 9m Entry taper 16mStraightening distance 24m
SHELTER
SHELTER
Figure 11.1 : Rigid Bus
Figure 11.2 : Articulated Bus
Parking2.1mParking 2.1m
Parking2.1mParking 2.1m
Figure 11: Kerbside stop with parking on approach and exit
Transport for London | 27
Overall length 23m
Exit taper 9m Straightening distance 14m
Overall length 29m
Exit taper 9m Straightening distance 20m
Bus Stop Flag
Bus Stop Flag
SHELTER
SHELTER
Parking 2.1m
Parking 2.1m
Figure 12.1 : Rigid Bus
Figure 12.2 : Articulated Bus
Figure 12: Exit side of pedestrian crossing
28
Accessible bus stop design guidance
SHELTER
SHELTER
Figure 13.1 : Rigid Bus
Figure 13.2 : Articulated Bus
Bus Stop Flag
Bus Stop Flag
Exit taper 9m Straightening distance 20m Entry taper 18m
Entry taper 18mExit taper 9m Straightening distance 24m
Overall length 33m
6m Radius
6m Radius
Loading2.5m
Loading2.5m
Loading2.5m
Loading2.5m
10m
10m
Overall length 29m
Figure 13: Exit side of junction
Transport for London | 29
Bus manoeuvresAt locations where buses often have tomanoeuvre around parked vehicles to pull upto and away from the stop, designers need tounderstand the implications of reducing thecage dimensions illustrated in Figures 11 to 13.
A clear exit distance of 9m is the minimumnecessary for buses to leave the stop and rejointhe general traffic lane without the rear of thevehicle overhanging the kerb in the vicinity ofwaiting passengers. Exceptionally, in a highlyconstrained situation, this dimension could bereduced to an absolute minimum of 7m.
Particular care is required when dealing withbus stops used by articulated buses, due tothe way they behave as they articulate. If the bus stop exit distance is reduced tobelow 9m, it is possible for the body of thebus to overhang the footway at the articulationpoint and the rear of the bus. This effect,which could pose a conflict with pedestrians, is illustrated in the adjacent photographs.
The rear section of a rigid bus can also behave inthe same way as the rear of an articulated bus.
Centre section of bus overhanging footway asit exits stop
Rear section of bus overhanging footway as itexits stop
30
Accessible bus stop design guidance
Alternative solutionsThere will be situations where none of thekerbside designs illustrated can beimplemented without seriously affectingexisting kerbside activity or general trafficoperations. This problem often arises at busystops, which require a very long length of kerbto be kept free from any other activity.
In many cases, stop accessibility will behampered by legal or illegal loading or parkingon the approach to the bus stop. In suchcases, it may not be physically possible for therear of the bus to manoeuvre close to thekerb. In other situations, site constraintsprevent conventional layouts from beingimplemented. Situations that cause problemsfor the siting of conventional kerbside busstops include:
● where there are loading or parking boxeswhich cannot be moved without causingundue inconvenience for frontage users;and
● where existing restrictions are neitherobserved nor effectively enforced.
In such cases a solution may be to alter thekerb line to assist bus access, for example byinstalling a bus boarder.
Transport for London | 31
7. Bus boarders
Bus boardersBus boarders are generally built out from theexisting kerb line and provide a convenientplatform for boarding and alighting passengers.There are two conventional types of busboarder, full width and half width. There are alsovariations on the bus boarder concept such as500mm build-outs in the downstream section ofbus bays (see Figure 19.1 on page 41).
The full width boarder offers by far the bestsolution for both bus and passenger accesswhilst minimising the kerb length required. Fullwidth boarders also serve to upgrade the imageof the bus by providing a platform that isseparate from the adjacent pedestrian flow, andthus move towards the standards achieved bytram and light rail systems.
Full width boardersA full width boarder should project far enoughinto the carriageway for the bus to avoidmanoeuvring past parked vehicles. For cars thisshould be at least 2m and a minimum of 2.6mwhere goods vehicles/vans are stopping. Thelength of the boarder will depend on thevehicle types that serve the stop in addition tothe bus frequency. Figure 14 shows typical fullwidth boarders. The length of kerbside spacerequired can be reduced by providing a shelter,open towards the kerb, on the existingfootway (see Figure 15.1). Where smaller miditype buses serve the stop, and no passengershelter is provided, it is possible to implementa boarder only 3m long (see Figure 15.2).
The benefits of a full width boarder are that it:
● minimises the kerbside space required;
● deters illegal parking;
● maintains the place of the bus in the trafficstream;
● allows the bus to line up parallel to thekerb, largely without manoeuvres;
● reduces boarding/alighting time;
● reduces overall time spent at the bus stop;and
● creates additional footway space forpassengers to wait.
Further details of the benefits of bus boardersare provided in Appendix B, which summarisesa study into the effects of bus boardersundertaken for Transport for London by TRL.
The ability of the bus to stop at a full widthboarder largely without manoeuvre providesthe opportunity for special kerbs to beinstalled with the aim to minimise the verticaland horizontal distances between the footwayand the bus floor (see Chapter 9).
The full width boarder keeps the position ofthe bus in the traffic stream, simplifying accessand improving bus reliability, as the bus is notdelayed waiting to rejoin the traffic stream.
Full width boarder
32
Accessible bus stop design guidance
Overall length 23m
Overall length 17m
Bus Stop FlagReflectorised bollards
Reflectorised bollardsBus Stop Flag
SHELTER
SHELTER
Figure 14.1 : Rigid Bus
Figure 14.2 : Articulated Bus
Loading2.5mLoading 2.5m
Loading2.5mLoading 2.5m
Figure 14: Full width boarder
Transport for London | 33
SHELTER
9.0m to 13.0m
Bus Stop Flag
Bus Stop Flag Reflectorised bollards
Reflectorised bollards
3m
Figure 15.1 : Rigid Bus
Figure 15.2 : Midi Bus
Loading2.5m
Loading2.5mLoading 2.5m
Loading 2.5m
Figure 15: Alternative full width boarder layouts
34
Accessible bus stop design guidance
Loading 2.5m Loading2.5m
Loading2.5mLoading 2.5m
SHELTER
SHELTER
Figure 16.1 : Rigid Bus + Rigid Bus
Figure 16.2 : Rigid Bus + Articulated Bus
Bus Stop FlagReflectorised bollards
Reflectorised bollardsBus Stop Flag
Overall length 41m
Overall length 35m
9m
9m
Figure 16: Multiple bus full width boarders
Transport for London | 35
Full width boarders should not be used wherethe frequency of buses or their dwell timeswill cause delay to following buses. There mayalso be circumstances where, for safetyreasons, it may not be appropriate toencourage an overtaking manoeuvre by othertraffic, such as near the brow of a hill or anapproach to a pedestrian refuge/island.
The design of bus boarders should provideincreased opportunities for the provision ofpassenger shelters. It is also essential thatboarders are properly designed andconstructed, particularly in relation tocarriageway and footway drainage. When makingany changes to kerb lines, designers shouldconsider the impact on cyclists, as abruptdeviations in alignment can create pinch-pointsfor two wheelers with general traffic.
Layouts for bus boarders to cater for multiplevehicles stopping at a single stop are providedin Figure 16 opposite.
Half width boardersThe half width boarder design is often a usefulcompromise solution. The build-out from thekerb can range from 500mm up to the width ofa full boarder, although they are commonly 1.0- 1.5m wide. They should be used wherefrequent delays to other vehicles are to beavoided or where a full width boarder wouldplace the bus in, or too close to, the opposingtraffic stream. As half width boarders are acompromise design, they use more kerb space,as some manoeuvring of the bus is required(see Figure 17 on page 37). Half width boardersretain some of the advantages of full widthboarders, as they still deter illegal parkingclose to or within the bus stop cage and theprospects of the bus stopping close to thekerb are improved. Half width boarders
36
Accessible bus stop design guidance
In circumstances where a layout has to caterfor more than one bus stopping at the sametime, provision should be made for the secondbus to pull out past the first bus and for alldoors of each vehicle to have clear access,unobstructed by street furniture.
Angled boardersParked vehicles on the approach to the stopoften result in buses stopping at an angle, with the front of the bus close to the kerb.Provision of a ‘wedge’ shaped or angledboarder can, in limited circumstances, improveaccess and enable the bus to stop adjacent tothe kerb in these situations. They have beenfound to be particularly suitable at stops onthe approach to junctions where the roadnaturally widens leading up to the junctionstop line. However, this is unlikely to besuitable at stops where the bus has to turnright at the downstream junction.
Angled boarder
The design of the angled boarder isconstrained by alignment, lane widths andapproach and exit arrangements. Designsshould be examined to check that vehiclesovertaking a stationary bus do not encroachunduly into the opposing traffic lane and thatbuses at adjacent stops can be safely passed.It is important that designs are tailored to sitespecific circumstances. Some sample layoutsare shown in Figure 18 (see page 38).
Safety concerns regarding these lessconventional layouts have been addressed informulating the designs. The following pointsare relevant when considering such a design:
● drivers often stop at an angle, and in asimilar position to that proposed throughnecessity rather than choice - the angledboarder simply formalises this arrangement;
● the driver’s blind spot is largely eliminatedas drivers pull forward and gain visibilitythrough their rear view mirrors beforecommitting themselves to manoeuvring intothe general traffic stream.
Transport for London | 37
Figure 17.1 : Rigid Bus
Figure 17.2 : Articulated Bus
Overall length 27m
Bus Stop Flag
Bus Stop FlagSHELTER
SHELTER
Overall length 35m
Straightening distance 18m Entry Taper 13mExit Taper
4m
Straightening distance 15m Entry Taper 8mExit Taper
4m
Parking2.1m
Parking2.1m
1m
1m
Parking 2.1m
Parking 2.1m
Figure 17: Half width boarder
38
Accessible bus stop design guidance
Overall length 32m
SHELTER
SHELTERBus Stop Flag
30m2m
Overall length 22m
20m2m
Bus Stop Flag
Reflectorised bollards
Reflectorised bollards
Loading2.5m
Loading2.5m
2.1m
2.1m
Figure 18.1 : Rigid Bus
Figure 18.2 : Articulated Bus
Figure 18: Angled boarders
Transport for London | 39
8. Bus bays
Bus bays (or lay-bys) present inherentoperational problems for buses and theyshould not be used unless there arecompelling safety or capacity reasons. TheMayor’s Transport Strategy lends furtherweight to this view in that priority should begiven, wherever possible, to efficient 'people-movers' such as buses. However, incircumstances where provision of a new bay isrequired the layout in Figure 19.1 isrecommended. This design incorporates abuild-out to allow buses to turn tightly intothe bay. In circumstances where two or morebuses may require access to the bay at onetime, the stop area will require lengthening.
Partial build-out within bus bay
As discussed in Chapter 5, a bus cage with 24-hour stopping controls, to prevent parkingor loading in the stop area, is recommended atall bus stops, (as shown in TSRGD diagram1025.4). There may also be a need to prohibitparking or loading on the approach to, and exitfrom the bay, although if this is the case, thejustification for a bus bay may be highlyquestionable.
There are many bus bays in use and the layoutof most of them prevents buses from reachingthe kerb effectively. The Bus PriorityPartnership Steering Group (which includesrepresentatives of London’s highwayauthorities) has approved a policy of filling inbus lay-bys on roads where the speed limit is30mph or less, unless there are compellingreasons for them to remain.
Research undertaken by TfL (see Appendix C)has shown that in-filling a lay-by and replacingit with a kerbside stop will:
● make it easier for the bus to stop adjacentto the kerb;
● make it easier and quicker for passengers toboard/alight; and
● reduce delays to buses by between 2 and 4seconds per bus.
Figure 20 (see page 42) shows modifications tobus bays that can improve bus access to thekerbside. Designers should note that withthese layouts, the bus protrudes into thenearside lane and amendments to traffic lanewidths might be required. An alternativesolution is to fill-in the bus bay completely,providing additional footway space that can betailored to the boarding and alightingcharacteristics required.
40
Accessible bus stop design guidance
At locations where there is persistent parkingin the bay, another variant is to fully fill asection of the bay, enabling the bus to stop onthe main carriageway, whilst retaining a shorterbay for loading activity (see Figure 19.2). As can be seen from a comparison of Figures19 and 20 with Figures 14 to 18, bus baysinevitably sterilise a far greater kerb lengththan any type of bus boarder.
Fully filled bus bay
Transport for London | 41
SHELTER
SHELTER
8m
2.5m
3m
8.5m
3.3m Radii tangent pointsRadii tangent points
25mRadius
25mRadius
1.5m
2m
Figure 19.1 : Partial buildout within bus bay
Figure 19.2 : Part filled bus bay with parking
Overall length 53m
Overall length 29m
Possible infilling
New Kerb Line
Existing bus bay
Bus Stop Flag
Bus Stop FlagParking / Loading
Entry taper 20mStraightening distance 18m
Straightening distance 16m Entry taper 13m
Exit taper 15m
Partial in-fill of bus bay
Figure 19: Bus bay arrangements
42
Accessible bus stop design guidance
Figure 20.1 : Rigid Bus
Figure 20.2 : Articulated Bus
Overall length 52m
Straighteningdistance 12m
Exit taper 20m
3m
3m3m
0.5 - 1.5mBus Stop Flag
0.5 - 1.5mBus Stop Flag
3m
Entry taper 20m
Entry taper 19mExit taper 20m
SHELTER
SHELTER
Straightening distance 26m
Overall length 65m
Bus encroaches intonearside lane
Bus encroaches intonearside lane
Partial in-fill of bus bay
Figure 20: Amendment to existing bus bay
Transport for London | 43
9. Kerb profiles andheights
Kerb heightsThe 'standard' kerb height at bus stops is125mm, although designers need to check siteconditions to obtain the correct gradient whena ramp is deployed. Allowance should be madefor the slight height differences between emptyand fully laden buses. A check should be madefor any potholes or gullies below the roadchannel, which could affect bus operation.
It is recommended that kerb heights of lessthan 125mm should be increased to amaximum of 140mm. Kerbs that are raised toa 140mm height produce a lower rampgradient and allow for resurfacing.
Kerb faces of between 125mm and 140mmhigh, are unlikely to require alteration.However, where kerbs are already being alteredat bus stops e.g. to build a bus boarder,consideration should be given to the use ofhigher kerbs to reduce the step height, therebyimproving access for all bus users includingthose with disabilities.
Where increased kerb heights are beingconsidered to reduce step heights, the groundclearance of buses must be taken into account.Although bus stop layouts have been designedto avoid the need for buses to overhang thekerb on arrival or departure, this may occur atparticular sites due, for example, toinconsiderate parking. Where there is apossibility of the bus body overhanging thekerb, the height of the kerb should be no higherthan the minimum ground clearance. Kerbheights greater than the ground clearance ofthe bus should only be used at locations where
there is no likelihood of the bus overhangingthe kerb. The use of high kerbs, standard kerbs,and the transition between them will needcareful consideration at bus stops.
‘Special’ kerbsThe ideal kerb arrangement should provideclose vertical and horizontal alignmentbetween the bus floor and adjacent footway.However, it is sometimes difficult for busdrivers to position their vehicles close to kerbsof traditional design, as they are not easilyseen from the drivers' cab position, and thedriver will wish to avoid damage to the vehicle.‘Special’ kerbs, such as ‘Kassel’ kerbs, providethe additional height required to reduce stepheight and have a profile to help guide the busalong the kerb edge and into a position withreduced horizontal gap between bus andfootway. These kerbs are more durable andless likely to be damaged by contact with bustyres. They are also made with materials thatare better able to cope with bus tyre contact,without damage to the tyre. TfL are aware ofthree such kerbs that are currently available inthe UK and these are shown in Figure 21.
The table overleaf gives the kerb heightsavailable. Transition kerbs are used to link thestandard kerb height to that of the ‘special’kerb adjacent to the bus stop.
44
Accessible bus stop design guidance
Appendix D provides contact details for thethree products listed.
For kerb faces up to 140mm, standard kerbs(to tie in with existing kerbs, where possible)are recommended, since there appears to beno advantage in using special kerbs in suchcircumstances.
It is recommended that a 160mm high 'special'kerb (i.e. Kassel / Charcon/ Marshalls) shouldonly be used where there is little or no lateralmovement of the bus and very little risk ofoverriding the kerb to get to the stop. This is due to:
● the different configurations of buschassis/body combinations in use;
● highway conditions in terms of varyingcamber of roadway, fall of footway, trenchreinstatement condition etc.; and
● fears for the safety of pedestrians wherekerbs are set unduly high.
‘Special’ kerbs are ideal for stops where thereis a full width bus boarder or no parking on theapproach (such as on the exit side of zig-zagmarkings or junctions). It will be beneficial tothe bus driver if, in the event that ‘special’kerbs are used, there is only one type installedalong any given route.
If ‘special’ kerbs are to be used, the followingwill need to be considered:
● footway drainage levels;
● gradient of footway;
● carriageway crossfall; and
● existing pedestrian activity.
Type Heights available Transition heights
Brett Landscaping 180mm or 120mm to 160 or‘Kassel’ Kerb 160mm 180mm
Camas (Charcon) 220mm or 125mm to 160mm andAccess Kerb 160mm 160mm to 220mm
The Marshalls Bus Stop Kerb is a two-piece system that allows for variable kerb height, up to 200mm.
‘Special’ bus stop kerb details
Transport for London | 45
Carriageway and footwaycrossfallsWhere kerb heights are changed, carriagewayand footway crossfalls will need to be carefullyconsidered. As a general rule, carriagewaycrossfalls in the region of 1 in 40, or 2.5%,should not present any additional difficultiesfor low floor buses. For carriageway crossfallssteeper than 2.5%, regrading of thecarriageway should be considered.
Footway crossfalls are also important and asteep backfall from the kerb is undesirable. A gradient of no more than 1 in 25 or 4% issuggested. To achieve this designers may haveto regrade lengths of footway to maintainadequate crossfalls or introduce complexdrainage arrangements. A common problemwith bus boarders is that works are onlyundertaken on the build-out, leading to steepcrossfalls. Ideally, footways should be regradedto the back of the footway, but this can addconsiderably to the cost of works.
In all cases where levels are being altered,careful consideration must be given toadequate drainage of the site, particularly inrelation to adjacent properties.
300
330
435
1000
150
180 (or 160)
180
Variable
100
1000
380
530
MarshallsBus Stop Kerb
Brett Landscaping‘Kassel’ Kerb
Camas (Charcon)Access Kerb
323
350
130
100
1000
52220 (or 160)
Figure 21: ‘Special’ kerbs
46
Accessible bus stop design guidance
10. Implementing busstop improvements
IntroductionDeciding on the location and layout for a busstop is only the first step in the improvementprocess. As part of this process designers will need to consider various issues to enablethe improvements to be undertaken. Thesemay include:
● Carriageway works;
● Footway works;
● Relocation and position of street furnituree.g. lamp columns, and telephone boxes;
● Statutory undertakers equipment;
● Provision/relocation of bus stop flag, shelter,‘Countdown’ display, and ticket machines;
● Traffic Regulation Orders (TROs);
● Planning permission or consents (for busshelters with advertising and ticketmachines);
● Consultation (statutory/public);
● Approval from highway authority andLondon Buses for works; and
● Power supply for shelter and/or ticketmachine.
The amount of work involved in implementingbus stop improvements should not beunderestimated. Co-ordinating the variousissues identified above can prove difficult andtime consuming, especially where multipleagencies are involved.
TimescalesIn planning the implementation ofimprovements, designers will need to take intoaccount the various timescales involved.Planning and co-ordination is vital. The flowchart and Gantt Chart (see Figures 22 and 23)on the following pages show standard tasksundertaken and typical timescales for thetypes of works normally associated with busstop improvement works.
BenefitsA well designed bus stop can providesignificant benefits. For example, at a stopserved by 20 bph, a 2 second saving per busprovides a value of time saving of almost£6,0001 per annum. At 5 seconds thisincreases to over £14,000.
Research undertaken by TfL has shown thatimplementing the types of layouts indicated inprevious chapters can make significant timesavings (see Appendices B and C) whilstmaking buses more accessible to all sectors ofthe population.
Worked examplesTo assist designers in the use of theseguidelines, some worked examples have beenprepared (see Appendix E). These illustratedifferent types of issues and how the guidelineshave been applied in the design solution.
1 This is calculated using the Transport for London Bus Priority Team Economic Evaluation with 20 bph every day andchanging from a 25 second to 23 second journey time.
Transport for London | 47
Site VisitReview Bus Stops
DevelopPreliminary DesignProposal (Options)
BackgroundHighway Authority
London Buses
Prepare Final Design
C2 Statutory UndertakersEnquiries
C3 Statutory Undertakers Enquiries
Stage 3 Road Safety Audit Snagging Report
Consultation With Immediate Frontagers / Highway Authority /
Emergency Services / Stakeholders
Review/CollateResponses & Report
Detailed Design
Stage 2 Road Safety Audit
Prepare & Submit Traffic Regulation Ordersand Deposit Drawings
Implementation
Update/RevisePreliminary Plan(Firmed Option)
Joint Inspection Meetingwith Stakeholders on Site
Stage 1Road Safety Audit
Undertake Pedestrian and Street Audit
Stage 1 - Review and Preliminary Design
Stage 2 - Consultation and Detailed Design
Telephone Kiosks
Street Light Column
Other
Revision Drawing
Construction (Design and
Management) Regs
Risk Assessment
Bill Of Quantities Construction Plans
Figure 22: Flow Chart of potential tasks for improving bus stops
48
Accessible bus stop design guidanceTask Name
Visit / Review StopObtain Boarding & Alighting DataDevelop Preliminary DesignCirculate to London BusesSite Meeting with Police / London BusesRevise DesignsC2 Statutory Undertakers EnquiriesTfL Notification / ApprovalConsultation with PublicCouncil / Member ApprovalTopographical SurveyDetailed DesignC3 Statutory Undertakers EnquiriesRelocate Bus Stop InfrastructureUndertake Stats DiversionsRelocate Lamp ColumnsTraffic Regulation OrdersUndertake Civils WorksCompletion
ID
12
3
4
5
67
8
910
111213
14
15
16
17
1819
Month1
Month2
Month3
Month4
Month5
Month6
Month7
Month8
Month9
Month10
Month11
Month12
1 day
1 wk
1 wk
1 day
3 days
2 wks
30 days
5 wks
4 wks
4 wks2 wks Detailed Design
C3 Statutory Undertakers Enquiries25 days
12 wks
12 wks Undertake Stats Diversions
Relocate Lamp Columns
18 wks
12 wks Traffic Regulation Orders
Undertake Civils Works2 wks
Completion
Relocate Bus Stop Infrastructure
Council / Member Approval
Topographical Survey
Consultation with Police
TfL Notification / Approval
C2 Statutory Undertakers Enquiries
Revise Designs
3 wks Circulate to London Buses
Site Meeting with Police / London Buses
Obtain Boarding & Alighting Data
Develop Preliminary Design
Visit / Review Stop
Figure 23: Gantt chart of standard tasks for improving bus stops
Transport for London | 49
11. Longer term issues
MaintenanceProviding facilities for low floor buses is a keystage in delivering a fully accessible busservice. Whilst London Buses is responsiblefor the bus stop flags and the majority of buspassenger shelters, local highway authoritieshave responsibilities for maintenance of busstop areas. This can include street cleaning,maintenance of the footway and carriagewaysurfaces in the vicinity of the bus stop, andwinter maintenance.
The carriageway, and potentially the kerb, inthe vicinity of the bus stop are subject toparticular stresses from the repeatedmanoeuvres of buses. Materials used in theseareas should be durable and any faults quicklyremedied. TfL’s Bus Priority Team is currentlyundertaking trials of new pavement designspecifications to reduce carriagewaydeformation, particularly rutting, at bus stops.
In the course of normal maintenance routines,carriageways will be resurfaced using a variety ofmethods. During resurfacing it is crucial that thekerb height at bus stops is maintained orimproved. It is common for the general level ofthe carriageway to rise with successive surfacerepairs. This not only increases stepping heightsand ramp gradients, to the detriment ofpassengers, but also increases crossfalls,causing additional problems for buses.
EnforcementThere have been considerable changes since2000, notably decriminalisation of Red Routerestrictions and Traffic Regulation Orders areno longer required for bus stop clearways.Many boroughs now use CCTV to enforce bus
stop clearways and waiting/loading restrictions, and this can contribute toimproved compliance.
Driver trainingWhilst this document gives guidance onlayouts to make bus stops fully accessible, it isequally important that buses are driven in amanner that fully utilises the facilities offeredby the low floor bus and compatible provisionsat the kerbside. TfL and operators haveimplemented extensive guidance and practicaltraining for all drivers. This guidance issupplemented by route specific training tocater for the particular route characteristics.
50
Accessible bus stop design guidance
12. Bibliography
Barham P. et al. (1994). ‘Accessible PublicTransport Infrastructure - Guidelines for theDesign of Interchanges, Terminals and Stops’,Mobility Unit of the Dept. of Environment,Transport and the Regions and the PassengerTransport Executive Group
Bus Priority Working Group (N.I.) (1997). ‘BusStops - A Design Guide for Improved Quality’,Translink and Dept. of the Environment forNorthern Ireland
Dejeammes M. (1997). 'Accessible Low FloorBus - System Approach in France',Transportation Research Record 1604, pp 163-169
Department for Transport (2002). ‘The TrafficSigns Regulations and General Directions’
DETR (1998). ‘Guidance on the Use of TactilePaving Surfaces’
Disabled Persons Transport AdvisoryCommittee (1997). ‘RecommendedSpecification for Low Floor Buses’
EC Directorate-General for Transport (1995).‘Low Floor Buses -The Low Floor Bus SystemFinal Report of the Action’, COST 322
Fruin J J (1987). ‘Pedestrian Planning andDesign’
Institution of Highways and Transportation(1997). ‘Transport in the Urban Environment’
Lavery I. and Davey S. (1996). 'The PedestrianEnvironment - The Achilles' Heel of Travel byLow Floor Bus?', Proceedings of Seminar F,PTRC
London Bus Priority Network (1996).‘Guidelines for the design of Bus Bays and BusStops to accommodate the European standard(12 metre) length bus’
Oscar Faber (1998). ‘Route 43 Quality BusService Project - Bus Stop Review - ExecutiveReport’
Traffic Director for London (1997).‘Implementation of Priority (Red) RoutesStandard Construction Details’
Transport for London (2002), Bus PriorityTeam. ‘Stage 2 Economic Evaluation’
Transport for London (2005). StreetscapeGuidance, Version 1
York I. and Balcombe R J (1998). ‘Evaluation ofLow Floor Bus Trials in London and NorthTyneside’, TRL Report 271
Transport for London | 51
Appendix A - Busmeasurements
Vehicle characteristicsThe vehicle characteristics to be taken intoaccount include:
● length of vehicle; type of bus i.e. midi,double deck or articulated bus;
● door locations and clear entry and exitwidths;
● floor height at doors;
● ramp position and length;
● swept path;
● overhang between nearside of busbodywork and front nearside tyrewall;
● external clearance height along nearside of bus; and
● ground clearance at points where the busmight potentially overhang the kerb.
The 'standard' busWithin these guidelines, unless indicatedotherwise, the layouts as provided are basedupon a 12 metre bus with front and centredoors and a ramp at the centre door. This is totake into account a 'worst case' in the contextof potential future operations. Layouts havealso been provided for an 18m articulated bus.Figure 24 shows dimensions of a 'standard'rigid bus and an articulated bus.
It is recommended that bus stops aredesigned, as a minimum, to accommodate the'standard' bus, with the following range ofvehicle dimensions, such that whereverpractical, designers can build appropriatedimensional tolerances.
'Standard' rigid bus dimensions
● Width: up to 2.55m
● Length: up to 12.00m
Door dimensions:
● Width: 1.1m
● Distance between 4.8m to 6.0m doors: (between centre lines of doors)
● Length of up to 1.0mextended ramp:
Heights between carriageway surface and bus floor (approximate):
● Front door: 325mm (normal)240mm (kneeling)
● Centre door: 335mm (normal)250mm (kneeling)
52
Accessible bus stop design guidance
6.00
12.00
2.55
0.55
1.00
0.25
1.00
1.00 1.000.50
2.10
2.80
1.10
3.20
2.52
8.94 7.27
1.80
2.69 5.20
1.79
1.30
4.12 3.16
0.550.
25
1.25
Figure 24.1 : Rigid Bus
All dimensions in metres
Figure 24.2 : Articulated Bus
Figure 24: Bus dimensions
Transport for London | 53
Table A1 – Vehicle dimensions for a variety of buses in service in London
Notes:All measurements are in mm with the exception of Approach and Depart Angle which are in degreesAll vehicles above are rigid with the exception of the Mercedes-Benz Citaro G which is articulated
Chassis
DennisDart SLF
DennisDart SLF
Transbus
Mercedes-BenzCitaro G
Mercedes-BenzCitaro
OptareSolo
OptareSolo
ScaniaOmniCity
Scania
DAFDB250
Volvo B7
Body
PlaxtonPointer 2
PlaxtonPointer 2
Enviro 300
Mercedes-Benz
Mercedes-Benz
Optare
Optare
East Lancs
Omnidekka
AlexanderALX 400
WrightEclipseGemini
Type
Midi bus
Single Deck
Single Deck
Articulated
Single Deck
Minibus
Minibus
Single Deck
DoubleDeck
DoubleDeck
DoubleDeck
OverallLength
8830
10735
12572
17940
11950
8500
9200
10630
10500
9790
10679
FrontOverhang
2315
2315
2630
2705
2705
675
675
6485
2365
2375
2531
Wheelbase(s)
3900
5805
6800
5845 (Front)5990 (Rear)
5845
5525
6225
5300
5225
5448
5700
RearOverhang
2615
2316
3142
3400
3400
675
675
2845
2910
2375
2448
OverallHeight
2856
2856
2910
3074
3076
2750
2750
2970
4210
4340
4407
Laden
325
325
325
320
320
265
265
320
315
320
320
Kneeled
245
245
250
N/A
N/A
200
200
N/A
N/A
250
250
ApproachAngle
8
8
7
7
7
N/A
N/A
N/A
7.5
N/A
7.14
DepartAngle
8
8
7
7
7
N/A
N/A
N/A
8
N/A
7.14
OverallWidth
2402
2402
2550
2550
2550
2500
2500
2550
2540
2550
2550
BodyTurningCircle
13140
19036
N/A
22800
21542
N/A
N/A
N/A
20218
15900
18000
Floor Height
54
Accessible bus stop design guidance
Appendix B - Effects ofintroducing bus boarders
Bus boarders provide a convenient platform forboarding and alighting passengers, and aregenerally built out from the existing kerb line.They are designed to enable the bus to stopparallel with the kerb, avoiding parked vehicles,and to move off again with an establishedposition in the traffic flow.
The Transport Research Laboratory (TRL)studied the effects of introducing bus boarderson buses, their passengers and other roadusers. The study comprised a series of ‘before’and ‘after’ surveys, undertaken in May 2002and May 2003 respectively, at four bus stopswhere boarders were being introduced:
1. Bryony Road, LB of Hammersmith & Fulham(Full width boarder);
2. South Croxted Road, LB of Southwark (Two half width boarders); and
3. Lupus Street, City of Westminster (Full width boarder).
Data collected during the surveys was analysed with the aim of investigating thefollowing issues:
● Accessibility for passengers;
● The impact on bus journey times;
● The impact on other traffic; and
● The economic impact of the change onroad users.
Additionally, Faber Maunsell consultants werecommissioned to analyse historical accidentdata, both ‘before’ and ‘after’ the introductionof bus boarders. A total of 23 sites were
investigated, including six angled boarders,twelve half width boarders and five full width boarders.
Results
The study identified the following benefits ofintroducing a bus boarder:
1. The percentage of buses stopping close tothe kerb increased at all four sites. The mostpronounced increase occurred at BryonyRoad, where initially no buses stopped closeto the kerb, but this improved to 95% ofbuses with the boarder. These results werebased on a subjective analysis of the positionof the bus in relation to the kerb.
2. Significantly fewer passengers had to stepinto the road when boarding and alighting atboarder sites leading to improved access tobuses, especially for mobility impairedpassengers. At three of the sites at least64% of passengers no longer had to stepinto the road with the boarder.
3. There was a slight reduction in boarding andalighting times of 0.1 seconds, possiblythrough improved stop accessibility.
4. Fewer buses (between 5% and 18%) werehemmed in by general traffic at the fullwidth boarder sites.
5. Those buses affected by traffic when pullingaway from a stop were delayed by between0.5 and 2.5 seconds less at the bus boarderthan with the original kerbside stop.
6. For all buses, the time taken to leave thebus stop and re-enter the main flow oftraffic was 0.6 to 0.8 seconds less after theintroduction of a bus boarder.
7. Overall bus delays were reduced by 1.3seconds on a road operating at 50%
Transport for London | 55
capacity, and up to 1.8 seconds on a roadoperating at 70% capacity.
8. At the two sites with parking problems, thenumber of parked vehicles at the stopdecreased significantly (at the 95%confidence level).
9. There were fewer conflicts betweenpedestrians and other road users at boarders.
This research indicates that there is a range ofbenefits for buses and their passengersassociated with introducing bus boarders.However, there is a very slight disadvantage toother traffic, which has greater difficultypassing a bus at the stop. This results inincreased queuing behind the bus andadditional delay to general traffic. On averagethe additional delay to other vehicles, causedby the bus boarder was between 0.07 secondsand 0.23 seconds per vehicle.
The full report contains an economicassessment which shows that on roadsoperating at below 50% of link capacity thecost benefit to bus passengers outweighs thedisbenefits to other road users. On roadsoperating at above 50% link capacity an overallbenefit may not be achieved. However, thesocial inclusion benefits offered by theconsiderable bus stop accessibilityimprovements have not been quantified andthese should not be underestimated.
In examining the road safety impacts ofintroducing a bus boarder:
1. Overall, there was no statistically significantchange in the number of recorded accidentsoccurring at bus stops at which busboarders have been implemented.
2. There was a decrease in accidents involvingpublic service vehicles (PSVs) in the vicinityof half-width and full width boarders.
3. In the vicinity of angled boarders an increasein accidents involving PSVs was recorded,although this did not appear to be linked tothe introduction of the bus boarder.
4. ‘Shunt’ type accidents increased in thevicinity of angled boarders.
ConclusionsThe introduction of bus boarders greatlyimproves accessibility for all passengersthereby helping to achieve objectives of socialinclusion. Illegal parking is significantly reducedand buses are able to pull away from the stopmuch more easily, reducing delays.
There are no apparent road safety issuesassociated with the introduction of half-widthand full-width boarders.
It is recommended that on TLRN and boroughroads subject to a 30mph speed limit or less,the introduction of bus boarders should beconsidered at bus stops where:
1. Parked or loading vehicles cause operationalproblems for buses; or
2. Buses have difficulty rejoining the maintraffic flow.
In considering the suitability of constructing abus boarder, the following characteristics ofeach stop should be evaluated:
1. Carriageway width;
2. Average traffic flows;
3. Visibility lines;
4. Frequency of bus services; and
5. Presence of a bus lane.
56
Accessible bus stop design guidance
Appendix C – Effects ofremoving bus lay-bys
Transport for London commissioned TheTransport Research Laboratory to study theeffects of filling in bus stop lay-bys uponbuses, their passengers and other road users.The study comprised a series of ‘before’ and‘after’ surveys, undertaken in May 2002 andMay 2003 respectively, at three bus stop sitesacross London:
1. Albany Road, LB of Southwark
2. Edgware Road, LB of Brent
3. Wandsworth Road, LB of Lambeth
In each of these cases, a bus stop with a lay-by was monitored before works were carriedout and after a suitable period to allow trafficpatterns to settle. The site was revisited whenthe lay-by had been infilled to bring the busstop kerb flush with the edge of the carriagewayso that stopped buses remained in the nearsidetraffic lane. At one site, the stop was located atthe nearside of a two lane carriageway, but atthe others, there was only a single marked lanein each direction, although in one case this wasrelatively wide. The data collected during thesesurveys were analysed with the aim ofinvestigating the following issues:
● The ways in which this affected accessibilityfor passengers;
● The effects upon bus journey times;
● The effects upon the delays andmovements of other traffic;
● The safety implications of the change for alltypes of road user; and
● The economic impact of the change onroad users and others.
The range of traffic flows observed rangedfrom approximately 38% to 56% of the linkcapacity. Filling in a bus lay-by and forming akerbside bus stop was found to providebenefits to bus passengers and buses thatvaried according to the level of traffic flows onthe link. However, stopping the bus in theinside lane reduced the capacity of the link andincreased traffic delay, although this is the caseat the vast majority of bus stops in London.
ResultsThe benefits found included the following:
1. Buses were able to stop close to the kerbat virtually all stopping events at two of thesurvey sites.
2. The improvement of being able to drawclose into the kerb was accompanied byfewer passengers needing to step into theroad when boarding and alighting, reducingthe percentage from between 3% and 24%to, at most, 1%. This could lead toimproved access to the buses, especially forpassengers with disabilities.
3. Passengers were able to board the busesfaster (by 0.5 to 1 seconds per passenger),possibly through this improvement inaccessibility. This change represents areduction of between 12% and 32% in theoriginal boarding times of 2.6 to 3.8 seconds.
4. Fewer buses were hemmed in by traffic,which causes delays when leaving the busstop. The percentage reduction of busesaffected by traffic was between 3% and 13%.
5. Overall the reduction in bus delay at a stopranged from 2 seconds on a road operatingat 50% capacity to 4 seconds on a roadoperating at 70% capacity.
Transport for London | 57
6. The variation in the stop time of buses wasreduced, leading to 95% of buses beingstationary in a time band 4 secondsnarrower than with a lay-by. Suchimprovements to the variability in run timescan assist in improving reliability of runtimes over the whole route.
7. Illegal parking at the bus stop wasconsiderably reduced by between 69% and83% at two of the study sites. At the othersite the parking increased, but this wasaccompanied by a considerable change intraffic patterns.
This research indicates that there was a rangeof bus passenger benefits associated withfilling in bus lay-bys. However, these arecounteracted by possible disadvantages forother road users, including increased queuingbehind the bus and extra delays. The fullreport contains an economic assessmentwhich indicates that the cost benefit to buspassengers outweighs the disbenefits to otherroad users. The degree of the relativeadvantages and disadvantages will depend ontraffic flows and road width at a given site.
ConclusionsBus stop dwell times are considerably reducedby filling in bus lay-bys. Illegal parking andobstruction of the bus stop is almosteliminated and accessibility for all users isgreatly increased, assisting in improving socialinclusion.
Policy● On TLRN roads, TfL will aim to fill in all bus
stop lay-bys in the urban environmentwhere the speed limit is 30mph or less,providing there are no prevailing safetyissues. Alternatively, the bus stop could berelocated to an appropriate kerbsidelocation.
● On Borough controlled roads, TfL willencourage the relevant highway authoritiesto follow the policy outlined above for theTLRN.
58
Accessible bus stop design guidance
Appendix D – ‘Special’ kerbs
Contact/product details below:
Company Product Contact details
Brett Landscaping Ltd Kassel Kerbs Sileby RoadBarrow upon SoarLoughboroughLeicestershireLE12 8LXTel: 01509 817187Fax: 01509 817197E-mail: [email protected]/landscaping
Camas (Charcon) Access Kerb Hulland WardAshbourne,DerbyshireDE6 3ETTel: 01335 372244Fax: 01335 370074www.charcon.com
Marshalls Bus Stop Kerb Landscape HousePremier WayLowfields Business ParkEllandHX5 9HTTel: 01422 312000www.marshalls.co.uk
Transport for London | 59
Bus Stop Name: Served by:
Location: Direction:Highway Authority:
AMHURST ROAD67, 76, 149, 243, N149, N243,40.5 buses per hourStoke Newington RoadSouthboundTransport for London
BEFORE AFTER
Site Description• Two-way highway on TLRN• Various retail frontages• Bus stop at downstream end of existing lay-by• Parking and loading bays at upstream end of lay-by
The Issues• Access to kerbside at bus stop obstructed by parked vehicles• Angle of kerbline prevents buses from stopping parallel to kerb• Buses experience difficulty rejoining general traffic flow• Bus stop clearway too short for frequency of services
The Improvements• New layout enables more than one bus to serve the stop• Buses stop in main carriageway and therefore are not delayed leaving the stop• Part filled lay-by retains 30m parking and loading bay• Increased footway width provides larger waiting area and allows ‘centre of footway’ shelter layout• New 160mm high ‘Special’ kerbs allow buses to pull in closer to the kerb.• Bus stop infrastructure renewed
NN
Worked example 1
Appendix E – Worked examples
Bus Stop Name: Served by:
Location: Direction: Highway Authority:
WHITE HART LANE STATION149, 259, 279, N149, N27923.5 buses per hourHigh Road, TottenhamSouthboundLB of Haringey
BEFORE AFTER
Site Description• Two-way highway on borough road• Various retail frontages• Bus stop within existing bus bay
The Issues• Bus bay attracts illegal parking, preventing access to stop• Buses experience difficulty rejoining general traffic flow• Poor layout of bus stop infrastructure prevents more than one bus serving the stop
The Improvements• New layout enables more than one bus to serve the stop• Buses stop in main carriageway and therefore are not delayed leaving the stop• Part filled lay-by retains 15m loading bay• Increased footway width provides larger waiting area• Bus stop infrastructure renewed
NN
Worked example 2
60
Accessible bus stop design guidance
Transport for London | 61
AcknowledgementsThe drafting and production of this documenthas involved the co-operation, input andconsultation with a number of individuals andorganisations. The main contributingorganisations are identified below:
● Transport for London, Surface Transport,Bus Priority Team;
● Transport for London, Surface Transport,London Buses;
● Transport for London, Equality andInclusion;
● London Bus Priority Network (LBPN);
● Faber Maunsell, St Albans.
Further information For further details or advice on the design ofaccessible bus stops, contact:
Bus Priority TeamTransport for LondonWindsor House, 42-50 Victoria StreetLondon, SW1H 0TLTel 0845 300 7000
Website: www.tfl.gov.uk