ACCESS -EXP -PLATE Module Layout
Transcript of ACCESS -EXP -PLATE Module Layout
1
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
ACCESS-EXP-PLATE Module Layout
FEATURES
The ACCESS-EXP-PLATE allows the MULTI-ACCESS-PSU2 system to be expanded by
adding further modules on hinged plates.
Please refer to PAK200500-ACCESS for full information on the Power Supply Unit.
Elmdene International Ltd �Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, �Fax: +44(0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK �Web: www.elmdene.co.uk
The ACCESS-EXP-PLATE is designed to accept a
variety of control boards in different
configurations:
Configuration 1:
EP2500, LNL-500, LNL-3300, LNL-8000
Configuration 2:
EP1502, EP4502, MR52, MR16IN, MR16OUT,
LNL-1000, LNL-1100, LNL-1200, LNL-1320,
LNL2000, LNL2220, LNL4420
Configuration 3:
EP1501, MR51e, LNL-1300e, LNL2210,
PW6101
Configuration 4: LNL-1100-U, LNL-1200-U,
LNL-1320-U
Configuration 5: MR50, LNL-1300-U, LNL-1300
2
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
For Configuration 1 fit supplied standoffs as indicated:
3
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
For Configuration 2 fit supplied standoffs as indicated:
4
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
For Configuration 3 fit supplied standoffs as indicated:
5
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
For Configuration 4 fit supplied standoffs as indicated:
6
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
For Configuration 5 fit supplied standoffs as indicated:
7
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
INSTALLATION
To fit the ACCESS-EXP-PLATE(s) to the MULTI-ACCESS-PSU2 (Note: The ACCESS-EXP-
PLATE comes with the bottom bush already fitted):
1. Fit the bottom bush into
the bottom panel hole in
the base.
2. Line the panel up with the
corresponding hole in the
top of the base.
3. Fit the top bush (supplied
with panel) into the hole
from the outside of the
enclosure.
4. Place the round part of
the panel on the bush so
that the panel engages in
the groove in the bush.
Push down on the panel
until it clips into place on
the bush.
8
Technical Support: +44(0)23 9269 6638 (option 3) PAK200797_01A Oct 2016 ©2016 ELMDENE INTERNATIONAL LTD
5. Fit earth lead from base to tab on the top edge of the panel.
6. Secure the panel to the standoffs in the base with the thumb screws
provided.
7. Repeat process for2nd panel.