AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.
-
Upload
earl-higgins -
Category
Documents
-
view
230 -
download
0
Transcript of AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.
![Page 1: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/1.jpg)
© Copyright 2012 Xilinx
AC701 Power Bus Reprogramming
![Page 2: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/2.jpg)
Page 2
Contents
Caution!
Xilinx AC701 Board
Hardware & Software Requirements
Setup
TI Fusion Digital Power Manufacturing Tool Tutorial
![Page 3: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/3.jpg)
Page 3
Caution!
The Texas Instruments software used in this presentation can adjust the power supply outputs on the AC701
If used improperly, it may seriously damage your AC701
Before making any adjustments not specifically covered in this presentation:– Understand the power requirements for Artix-7 Devices– Understand the consequences of the change you are making
![Page 4: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/4.jpg)
Page 4
Xilinx AC701 Board
![Page 5: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/5.jpg)
Page 5
Hardware Requirements
Texas Instruments USB Interface Adapter EVM– TI Part Number: USB-TO-GPIO
![Page 6: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/6.jpg)
Page 6
Software Requirements
Texas Instruments Power Software– TI Part Number: FUSION_MFR_GUI– Download: Latest Release at http://www.ti.com/tool/fusion_mfr_gui
![Page 7: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/7.jpg)
Page 7
Software Setup
Install the TI Fusion Digital Power Manufacturing Software
![Page 8: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/8.jpg)
Page 8
Connect TI USB Interface Adapter
On the TI USB Adapter– Connect the Ribbon Cable– Connect the USB Cable
![Page 9: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/9.jpg)
Page 9
Connect TI USB Interface Adapter (2)
Connect the Ribbon Cable to the AC701– Red Stripe towards pin 1
– Insert the “A” end of the USB cable into a PC USB port (do not use a docking station or USB hub port)
– Turn on the AC701 board
![Page 10: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/10.jpg)
Page 10
Restoring Power Levels
Unzip included file: AC701_RevB_TI_XML.zip
![Page 11: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/11.jpg)
Page 11
TI Fusion Digital Power Designer Tool
Power up the AC701
Go to Texas Instruments Fusion Digital Power Designer > Tools > Firmware & Configuration Download Tool:
![Page 12: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/12.jpg)
Page 12
TI Fusion Digital PowerFirmware & Configuration Download Tool
When the Fusion Digital Power Firmware & Configuration Download Tool window opens the following fields need to be completed:– IC Family: UCD3xxx / UCD92xx / UCD90xx– Project File Write Options (Used for All Devices):
Ignore write read back mismatch warnings (NACKs will still abort programming)Force write of all parameters (normally only differences are written)
– Addr(ess of controller you wish to write to)– Project File (radio button)– Navigate to the location of .xml configuration file for this controller and select
Once configuration section is complete, click Start
Up to 4 devices can be written from one instance
See next slide for GUI representation
![Page 13: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/13.jpg)
Page 13
TI Fusion Digital PowerFirmware & Configuration Download Tool
![Page 14: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/14.jpg)
Page 14
TI Fusion Digital PowerFirmware & Configuration Download Tool - Example
Select file and type
in the corresponding
Addr as shown in the
figure.
AC701 U9
Addr102
AC701 U8
Addr102
Click Start.
![Page 15: AC701 Power Bus Reprogramming © Copyright 2012 Xilinx.](https://reader036.fdocuments.net/reader036/viewer/2022062516/56649db65503460f94aa8570/html5/thumbnails/15.jpg)
Page 15
TI Fusion Digital PowerFirmware & Configuration Download Tool - Example
See completed message.