Laboratory Evaluation of ZycoSoil as an Anti-Stripping Agent on Superpave Mixtures
Absorption & Stripping of Dilute Mixtures
-
Upload
marcomexico -
Category
Documents
-
view
197 -
download
2
Transcript of Absorption & Stripping of Dilute Mixtures
![Page 1: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/1.jpg)
Absorption and Absorption and Stripping of Stripping of Dilute Mixtures Dilute Mixtures
Chapter6Chapter6
![Page 2: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/2.jpg)
Key and Difficult Points:Key Points Equipment of Absorption and Stripping Graphical Equilibrium-Stage Method for Trayed Towers Algebraic Method for Trayed Towers Rate-Based Method for Packed TowersDifficult Points Algebraic Method for Trayed Towers Rate-Based Method for Packed Towers
Purpose and Requirements: Know Equipment of Absorption and Stripping Learn to Design a trayed Tower and a packed Tower
![Page 3: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/3.jpg)
Outline
6.1 EQUIPMENT 6.2 GENERAL DESIGN CONSIDERATIONS 6.3 GRAPHICAL EQUILIBRIUM-STAGE METHOD FOR TRAYED
TOWERS 6.4 ALGEBRAIC METHOD FOR DETERMINING THE NUMBER OF
EQUILIBRIUM STAGES 6.5 STAGE EFFICIENCY 6.6 TRAY CAPACITY, PRESSURE DROP, AND MASS
TRANSFER 6.7 RATE-BASED METHOD FOR PACKED COLUMNS 6.8 PACKED COLUMN EFFICIENCY, CAPACITY, AND
PRESSURE DROP 6.9 CONCENTRATED SOLUTIONS IN PACKED COLUMNS
![Page 4: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/4.jpg)
Absorption (Gas Absorption/Gas Scrubbing/Gas Washing吸收 )
Gas Mixture (Solutes or Absorbate) Liquid (Solvent or Absorbent)
Separate Gas Mixtures Remove Impurities, Contaminants, Pollutants, or
Catalyst Poisons from a Gas(H2S/Natural Gas) Recover Valuable Chemicals
![Page 5: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/5.jpg)
Figure 6.1 Typical Absorption Process
Chemical Absorption
(Reactive Absorption)
Physical Absorption
![Page 6: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/6.jpg)
Absorption Factor(A吸收因子 )
A = L/KV
Component A = L/KV K-value
Water 1.7 0.031
Acetone 1.38 2.0
Oxygen 0.00006 45,000
Nitrogen 0.00003 90,000
Argon 0.00008 35,000 •Larger the value of A, Fewer the number of stages required•1.25 to 2.0 , 1.4 being a frequently recommended value
![Page 7: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/7.jpg)
Stripping (Desorption解吸 )
Stripping Distillation
Stripping Factor(S解吸因子 )
S = 1/ A= KV/L High temperature Low pressure is desirable
Optimum stripping factor : 1.4.
![Page 8: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/8.jpg)
6.1 EQUIPMENT
Figure 6.2 Industrial Equipment for Absorption and Stripping
trayed tower packed column
spray towerbubble column
centrifugal contactor
![Page 9: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/9.jpg)
Figure 6.3 Details of a contacting tray in a trayed tower
Trayed Tower(Plate Clolumns板式塔 )
![Page 10: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/10.jpg)
Figure 6.4 Three types of tray openings for passage of vapor up into liquid
(d) Tray with valve caps
(b) valve cap (c) bubble cap (a) perforation
![Page 11: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/11.jpg)
Figure 6.5 Possible vapor-liquid flow regimes for a contacting tray
(a) Spray(b) Froth(c) Emulsion(d) Bubble(e)Cellular Foam
Froth Liquid carries no vapor bubbles to the tray belowVapor carries no liquid droplets to the tray aboveNo weeping of liquid through the openings of the tray
Equilibrium between the exiting vapor and liquid phases is approached on each tray.
![Page 12: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/12.jpg)
Packed Columns
Figure 6.6 Details of internals used in a packed column
![Page 13: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/13.jpg)
Figure 6.7 Typical materials used in a packed column
Packing Materails
(a) Random Packing Materials(b) Structured Packing Materials
•More surface area for mass transfer•Higher flow capacity•Lower pressure drop
•Expensive
•Far less pressure drop •Higher efficiency and capacity
![Page 14: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/14.jpg)
6.2 ABSORBER/STRIPPER DESIGN
6.2.1 General Design Considerations 6.2.2 Trayed Towers 6.2.2.1 Graphical Equilibrium-Stage 6.2.2.2 Algebraic Method for Determining the Number of Equilibrium 6.2.2.3 Stage Efficiency 6.2.3 Packed Columns 6.2.3.1 Rate-based Method 6.2.3.2 Packed Column Efficiency, Capacity, and Pressure Drop
![Page 15: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/15.jpg)
6.2.1 General Design Considerations
1. Entering gas (liquid) flow rate, composition, temperature, and pressure
2. Desired degree of recovery of one or more solutes3. Choice of absorbent (stripping agent)4. Operating pressure and temperature, and allowable
gas pressure drop5. Minimum absorbent (stripping agent) flow rate and
actual absorbent (stripping agent) flow rate as a multiple of the minimum rate needed to make the separation
Design or analysis of an absorber (or stripper) requires consideration of a number of factors, including:
6. Number of equilibrium stages7. Heat effects and need for cooling (heating)8. Type of absorber (stripper) equipment9. Height of absorber (stripper)10. Diameter of absorber (stripper)
![Page 16: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/16.jpg)
SUMMARY
1. A liquid can be used to selectively absorb one or more components from a gas mixture. A gas can be used to selectively desorb or strip one or more components from a liquid mixture.
2. The fraction of a component that can be absorbed or stripped in a countercurrent cascade depends on the number of equilibrium stages and the absorption facto: A = L/KV, or the stripping factor, S = KV/L, respectively.
3. Absorption and stripping are most commonly conducted in trayed towers equipped with sieve or valve trays, or in towers packed with random or structured packings.
4. Absorbers are most effectively operated at high pressure and low temperature. The reverse is true for stripping. However, high costs of gas compression, refrigeration and vacuum often preclude operation at the most thermodynamically favorable con ditions.
5. For a given gas flow rate and composition, a desired degree of absorption of one or more components, a choice of absorbent, and an operating temperature and pressure, there is a minimum absorbent flow rate, given by (6-9) to (6-11), that corresponds to the use of an infinite number of equilibrium stages. For the use of a finite and reasonable number of stages, an absorbent rate of 1.5 times the minimum ' is typical. A similar criterion, (6-12), holds for a stripper.
![Page 17: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/17.jpg)
6. The number of equilibrium stages required for a selected absorbent or stripping agent flow rate for the absorption or stripping of a dilute solution can be determined from the equilibrium line, (6-1), and an operating line, (6-3) or (6-5), using graphical algebraic, or numerical methods. Graphical methods, such as Figure 6.11, offer considerable visual insight into stage-by-stage changes in compositions of the gas and liquid streams.
7. Rough estimates of overall stage efficiency, defined by (6-21), can be made with the correlations of Drickamer and Bradford, (6-22), O'Connell, (6-23), and Figure 6.15 More accurate and reliable procedures involve the use of a small Oldershaw column , or semitheoretical equations, e.g., of Chan and Fair, based on mass transfer considerations, to determine a Murphree vapor-point efficiency, (6-30), from which a Murphrtf vapor tray efficiency can be estimated from (6-31) to (6-34), which can then be related to the overall efficiency using (6-37).
8. Tray diameter can be determined from (6-44) based on entrainment flooding consid erations using Figure 6.24. Tray vapor pressure drop, the weeping constraint, entrainment, and downcomer backup can be estimated from (6-45), (6-64), (6-65), (6-66), respectively.
![Page 18: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/18.jpg)
9. Packed column height can be estimated using the HETP, (6-69), or HTU/NTU,(6-85), concepts, with the latter having a more fundamental theoretical basis in the two-film theory of mass transfer. For straight equilibrium and operating lines, HETP is related to the HTU by (6-90), and the number of equilibrium stages is related to the NTU by (6-91).
10. Below a so-called loading point, in a preloading region, the liquid holdup in a packed column is independent of the vapor velocity. The loading point is typically about 70% of the flooding point and most packed columns are designed to operate in the preloading region at from 50% to 70% of flooding. From the GPDC chart of Figure 6.36, the flooding point can be estimated, from which the column diameter can be determined with (6-98
![Page 19: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/19.jpg)
11. One significant advantage of a packed column is its relatively low pressure drop per unit of packed height, as compared to a trayed tower. Packed column pressure drop can be roughly estimated from Figure 6.36 or more accurately from (6-100).
12. Numerous rules of thumb are available for estimating the HETP of packed columns. However, the preferred approach is to estimate hog from separate semitheoretical mass transfer correlations for the liquid and gas phases, such as those of (6-123) and (6-124) based on the extensive experimental work of Billet and Schultes.
13. Determination of theoretical stages for concentrated solutions involves numerical integration because of curved equilibrium and/or operating lines.
![Page 20: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/20.jpg)
REFERENCES
1. Washburn, E.W., Ed.-in-Chief, International Critical Tables, McGraw-Hill, New York, Vol. Ill, p. 255 (1928).
2. Lockett, M., Distillation Tray Fundamentals, Cambridge University Press, Cambridge, UK, p. 13 (1986).
3. Okoniewski, B.A., Chem. Eng. Prog., 88 (2), 89-93 (1992). 4 Sax, N.I., Dangerous Properties of Industrial Materials, 4th ed., Van
Nostrand Reinhold, New York, pp. 440-441 (1975). 5. Lewis, W.K., Ind. Eng. Chem., 14, 492-497 (1922). 6. Drickamer, H.G., and J.R. Bradford, Trans. AICHE, 39, 319-360 (194
3). 7. Jackson, R.M., and T.K. Sherwood, Trans. AIChE, 37, 959(1941). 8. S- O'Connell, H.E., Trans. AIChE, 42, 741-755 (1946). 9.Walter, J.F., and T.K. Sherwood, Ind. Eng. Chem., 33, 493-XH (194
1). 10. Edmister, W.C., The Petroleum Engineer, C45-C54 (Jan. 1949).
![Page 21: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/21.jpg)
11. Lockhart, F.J., and C.W. Leggett, in K.A. Kobe and J.J. McKetta, Jr., Ed., Advances in Petroleum Chemistry and Refining,vol. 1, Interscience, New York, Vol. 1, pp. 323-326 (1958).
12. Holland, C.D., Multicomponent Distillation, Prentice-Hall, Englewood Cliffs. NJ, 1963.
13. Murphree, E.V., Ind. Eng. Chem., 17, 747 (1925). 14. Hausen, H., Chem. Ing. Tech., 25, 595 (1953). 15. Standart, G., Chem Eng. ScL, 20, 611 (1965). 16.Lewis, W.K., Ind. Eng. Chem., 28, 399 (1936). 17. Gerster, J.A., A.B. Hill, N.H. Hochgraf, and D.G. Robinson, Tray Effic
iencies in Distillation Columns," Final Report from the University of Delaware, American Institute of Chemical Engineers, V* York (1958).
18. Bubble-Tray Design Manual, AIChE, New York (1958). 19.Gilbert. T.J., Chem. Eng. ScL, 10, 243 (1959). 20.Barker, P.E., and M.F. Self, Chem. Eng. ScL, 17, 541 (1962).
![Page 22: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/22.jpg)
21. Bennett, D.L., and H.J. Grimm, AIChE J., 37, 589 (1991). 22. O'dershaw, C.F., Ind. Eng. Chem. Anal. Ed., 13, 265 (1941). 23.Fair. J.R., H.R. Null, and W.L. Holies, Ind. Eng. Chem. Process Des.Dev., 2
2, 53-58 (1983). 24.Souders, M., and G.G. Brown, Ind. Eng. Chem., 26, 98-103 (1934). 25.Fair,J.R., Peiro/Chem. Eng., 33, 211-218 (Sept. 1961). 26. Sherwood, T.K., G.H. Shipley, and F.A.L. Holloway, Ind. Eng. Chem., 30, 7
65-769 (1938). 27. Glitsch Ballast Tray, Bulletin No. 159, Fritz W. Glitsch and Sons, Dallas, TX
(from FRI report of Sept. 3, 1958). 28. Glitsch V-l Ballast Tray, Bulletin No. 160, Fritz W. Glitsch and Sons, Dallas,
TX (from FRI report of Sept. 25, 1959). 29. Oliver, E.D., Diffusional Separation Processes. Theory, Design, and Evaluat
ion, John Wiley and Sons, New York, pp. 320-321 (1966). 30. Bennett, D.L., R. Agrawal, and P.J. Cook, AIChE J., 29, 434-442 (1983).
![Page 23: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/23.jpg)
31. Smith, B.D., Design of Equilibrium Stage Processes, McGraw-Hill, New York (1963).
32. Klein, G.F., Chem. Eng., 89 (9), 81-85 (1982). 33. Kister, H.Z., Distillation Design, McGraw-Hill, New York (1992). 34. Lockett, M.J., Distillation Tray Fundamentals, Cambridge Uni versity Press,
Cambridge, UK, p. 146 (1986). 35. American Institute of Chemical Engineers (AIChE), Bubble-Tray Design Ma
nual, AIChE, New York, (1958). 36. Chan, H., and J.R. Fair, Ind. Eng. Chem. Process Des. Dev., 23,814-819 (1
984). 37. Chan, H., and J.R. Fair, Ind. Eng. Chem. Process Des. Dev., 23,820-827 (1
984). 38. Scheffe, R.D., and R.H. Weiland, Ind. Eng. Chem. Res., 26,228-236 (1987). 39. Foss, A.S., and J.A. Gerster, Chem. Eng. Prog., 52, 28-J to34-J (Jan. 1956). 40. Gerster, J.A., A.B. Hill, N.N. Hochgraf, and D.G. Robinson, "Tray Efficiencie
s in Distillation Columns," Final Report from Uni versity of Delaware, American Institute of Chemical Engineers (AIChE), New York (1958).
![Page 24: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/24.jpg)
41. Fair, J.R., Petro./Chem. Eng., 33 (10), 45 (1961). 42. Colburn, A.P., Ind. Eng. Chem., 28, 526 (1936). 43. Chilton, T.H., and A.P. Colburn, Ind. Eng. Chem., 27, 255-260, 904 (1935). 44. Colburn, A.P., Trans. AIChE, 35, 211-236, 587-591 (1939). 45. Billet, R., Packed Column Analysis and Design, Ruhr-University Bochum (1
989). 46. Stichlmair, J., J.L. Bravo, and J.R. Fair, Gas Separation and Purification, 3,
19-28 (1989). 47. Billet, R., and M. Schultes, Packed Towers in Processing and Environmenta
l Technology, translated by J. W. Fullarton, VCH Pub lishers, New York (1995). 48. Leva, M., Chem. Eng. Prog. Symp. Ser., 50 (10). 51 (1954). 49. Leva, M., Chem. Eng. Prog., 88, (1) 65-72 (1992). 50. Kister, H.Z., and D.R. Gill, Chem. Eng. Prog., 87 (2), 32-42(1991).
![Page 25: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/25.jpg)
51. Billet, R., and M. Schultes, Chem. Eng. Technoi, 14, 89-95(1991). 52. Ergun, S., Chem. Eng. Prog., 48 (2), 89-94 (1952). 53. Kunesh, J.G., Can. J. Chem. Eng., 65, 907-913 (1987). 54. Whitman, W.G., Chem. and Met. Eng., 29, 146-148 (1923). 55. Sherwood, T.K., and F.A.L. Holloway, Tram. AIChE., 36,39-70 (19
40). 56. Cornell, D., W.G. Knapp, and J.R. Fair, Chem. Eng. Prog., 56(7) 6
8-74 (1960). 57. Cornell, D., W.G. Knapp, and J.R. Fair, Chem. Eng., Prog., 56(8), 4
8-53 (1960). 58. Bolles, W.L., and J.R. Fair, Inst. Chem. Eng. Symp. $er 3/35 (1979).
59. Bolles, W.L., and J.R. Fair, Chem. £>ig.,89(14), 109-116 (1982) 60. Bravo, J.L., and J.R. Fair. Ind. Eng. Chem. Process Des.Devel.21,1
62-170(1982).
![Page 26: Absorption & Stripping of Dilute Mixtures](https://reader036.fdocuments.net/reader036/viewer/2022081715/547b8e4fb4af9fff648b459d/html5/thumbnails/26.jpg)
61. Bravo, J.L., J.A. Rocha, and J.R. Fair, Hydrocarbon Processing 64 (1), 56-60 (1985).
62. Fair, J.R., and J.L. Bravo, Chem. E. Symp. Ser., 104, A183-A201 (1987).
63. Fair, J.R., and J.L. Bravo, Chem. Eng. Prog., 86 (1). 19-29 (1990). 64. Shulman, H.L., C.F. UHrich, A.Z. Proulx, and J.O. Zimmerm, AICh
E J., 1, 253-258 (1955). 65. Onda, K., H. Takeuchi, and Y.J. Okumoto, J. Chem. Eng .jpn., 1,
56-62 (1968). 66. Billet, R., Chem. Eng. Prog., 63 (9), 53-65 (1967). 67. Billet, R., and M. Schultes, Beitrage zur Verfahrens-Und
Umweltechnik, Ruhr-Universitat Bochum. pp. 88-106 (1991). 68. Higbie, R., Trans. AIChE, 31, 365-389 (1935).