Radar 2009 A_8 Anten.. - This Free Radar Systems Engineering
a_8
2
Global configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be
-
Upload
lambanaveen123 -
Category
Documents
-
view
216 -
download
0
description
tempo
Transcript of a_8
Global configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in theGlobal configuration register (CFG_GCR) 1.3.1 Activation level The MCU activation level is configured by programming the AL bit in the CFG_GCR register. For information on the use of this bit refer to Section 6.4: Activation level/low power mode control on page 62. 1.3.2 SWIM disable By default, after an MCU reset, the SWIM pin is configured to allow communication with an external tool for debugging or Flash/EEPROM programming. This pin can be configured by the application for use as a general purpose I/O. This is done by setting the SWD bit in the
