A70 Chassis Collision Repair Manual.pdf

Manual Name Pub. No.7MGE Engine Repair Manual

TOYOTA SUPRA Chassis and BodyRepair Manual

TOYOTA SUPRA Chassis and BodyRepair Manual Supplement

TOYOTA SUPRA Electrical WiringDiagram Manual

TOYOTA SUPRA Repair Manual(USA and Canada)

TOYOTA SUPRA Electrical WiringDiagram Manual (USA and Canada)

Fundamental Body Repair Procedures

Fundamental Painting Procedures

BRM002E

36438E

M/Y Version

M/Y Version

EWD013E

RM036E

RM029E

RM027E

FOREWORD

This repair manual has been prepared to provide information onthe repair methods (including cutting and welding operations,but excluding painting) recommended by TOYOTA for collisiondamaged body components of the TOYOTA SUPRA.

Applicable models: MA70 series

This manual consists of body repair methods, exploded dia-grams and illustrations of the body components and other infor-mation relating to body panel replacement such as handling pre-cautions, tools, equipment, etc. However, it should be noted thatthe front fenders of all TOYOTA models are bolted on and re-quire no welding.

Body construction will sometimes differ depending on specifica-tions and country of destination. Therefore, please keep in mindthat the information contained herein is based on vehicles forgeneral destinations.

For the service of specifications and repair procedures otherthan collisiondamaged body components of the TOYOTASUPRA, refer to the following repair manuals.

All information contained in this manual is the most uptodateat the time of publication. However, specifications and proce-dures are subject to change without prior notice.

TOYOTA MOTOR CORPORATION

1

mm in.87 3.15

200 7.87

QUARTER PANEL

Cut and Join Location

HOW TO USE THIS MANUALEach repair method description provided in Section RE of this manual comprises two pages, divided into2 blocks (REMOVAL AND INSTALLATION) and includes illustrations to facilitate body repair.

RE26 BODY PANEL REPLACEMENTRear Body Components

QUARTER PANEL (CUT)

REMOVAL

Cut and Join Location200 mm

80 mm

[Cut and Join Location]

Front

Braze

Rear

1. Cut and join the quarter panel as shown above.

REPLACEMENT PART AND METHOD

(CUT)Replacement method

(ASSY) Assembly replacement. . . . . (CUT) Major cutting (less than 1/2 of part used). . . . . . (CUTH) Half cutting (about 1/2 of part used). . . . (CUTP) Partial cutting (most of part used). . . .

Replacement part

BODY VARIATIONS AND PART LOCATIONBody variations: Non All models. . . .

REMOVAL DIAGRAMDescribes in detail removal of the damaged part involving repair by cutting.

REMOVAL GUIDEProvides additional information to more efficiently help you perform the removal.

INTRODUCTIONIN-2

mm in.5 0.20

1. Before temporarily installing the new part, applybody sealer to the wheel arch portion.

NOTE:1) Apply sealer approx. 5 mm (0.20 in.) from the

flange, avoiding any oozing.

2) Apply evenly, approx. 3 4 mm (0.12 0.16 in.)in diameter.

3) For other sealing points, refer to section SU.

BODY PANEL REPLACEMENTRear Body Components RE27

INSTALLATION

Butt Weld

Butt Weld

Body Sealer

Braze

Body Sealer

About 5 mm

2. Temporarily installing the new part and check the fit ofthe front door, luggage compartment door and rearcombination lamp.

INSTALLATION DIAGRAMDescribes in detail installation of the new part involving repair by welding and/or cutting, but exclud-ing painting.

INSTALLATION GUIDEProvides additional information to more efficiently help you perform the installation.

SYMBOLSSee page IN4.

ILLUSTRATION OF WELD POINTWeld method and panel position symbols.See page IN5.

INTRODUCTION IN-3

SYMBOLS MEANING ILLUSTRATION

SAW CUT ORROUGH CUT

REMOVE BRAZE

(See page IN5)

SPOT WELD ORMIG PLUG WELD

WELD POINTS

BRAZE

CONTINUOUS MIGWELD (BUTT WELDOR TACK WELD)

BODY SEALER

SYMBOLSThe following symbols are used in the welding Diagrams in Section RE of this manual to indicate cuttingareas and the types of weld required.

INTRODUCTIONIN-4

Remove weld point and panel position

Weld points

REMOVAL

Weld method and panel position

Weld points

INSTALLATION

SYMBOL MEANING ILLUSTRATION SYMBOL

Spot Weld

MEANING ILLUSTRATION

RemoveWeldPoints

(Outside)

Mig PlugWeld

(Middle)

(Inside)

Spot MIGWeld

HINT: Panel position syrnbols are as seen from theworking posture.

Illustration of Weld Point Symbols

EXAMPLE:

INTRODUCTION IN-5

GENERAL REPAIR INSTRUCTIONSWork Precautions

SAFETY1. Before performing repair work, check

for fuel leaks. If a leak is found, be sureto close the opening totally.

2. If it is necessary to use a frame in thearea of the fuel tank, first remove thetank and plug the fuel line.

SAFETYNever stand in directline with the chain whenusing a puller an thebody or frame, and besure to attach a safetycable.

VEHICLE PROTECTIONWhen welding, protect thepainted surfaces, windows,seats and carpet with heatresistant, fireproof covers.

WRONG

Glass Cover

Safety Cable

Seat Cover

WRONG

SAFETYBefore performing repair work,disconnect the battery cables.

SAFETY WORK CLOTHES

In addition to the usual mechanic wear, cap and Safety shoes,the necessary gloves, head protector, glasses, ear plugs, faceprotector, dustprevention mask, etc. should be worn as thesituation demands.

WeldersGlasses Body

MechanicStand

DustPreventionMask

FaceProtector

EarPlugs

HeadProtector Welders

Gloves

HAND TOOLSKeeping your hand toolsin neat order will havean effect on your workefficiency.

SafetyShoes

CottonGloves

INTRODUCTIONIN-6

REMOVAL OF ADJACENTPARTSWhen removing adjacent partsby avoid accidental marring,etc., wrapping the tools usedand surrounding body parts inprotective tape.NOTE:1) Take particular care not

to damage any screw orclip holes.

2) If you do scratch apainted surface, retouchimmediatly after. Even asmall scratch will resultin rust and corrosion.

Proper and Efficient Work Procedures

REMOVAL

REMOVAL. OF ADJACENT COMPONENTSWhen removing adjacent components, applyprotective tape to the surrounding body andyour tools to prevent damage.CAUTION:1. Be especially careful not to damage

screw or clip holes.2. If the paint is accidently scratched, ap-

ply touchup paint immediately. Eventhe slightest scratch may result in cor-rosion or appearance of rust.

NO. OF SPOT WELDSMake a note of the number of spot weldsfor later reference.NOTE: The number of spot welds mayvary depending on the vehicle.

PREREMOVAL MEASURINGBefore removal or cutting opera-tions, take measurements in ac-cordance with the dimension dia-gram. Always use a puller tostraighten a damaged body orframe.

CUTTING AREAAlways cut in a straightline and avoid reinforcedareas.

PRECAUTIONS FOR DRILLING ORCUTTINGCheck behind any area to be drilled orcut to insure that there are no hoses,wires, etc., that may be damaged.

Cutting Okay

CornersReinforcement

WRONG

INTRODUCTION IN-7

INSTALLATION

WELDING PRECAUTIONS1. The number of welding spots

should be as follows.Spot weld: 1.3 x No. ofmanufacturers spots.Plug weld: More than No. ofmanufacturers plugs.

POSTWELDING REFINISH-ING1. Always check the welded

spots to insure they aresecure.

2. When smoothing out theweld spots with a discgrinder, be careful not togrind off too much as thiswould weaken the weld.

PREWELDING MEASUREMENTSAlways take measurements beforeinstalling underbody or engine com-ponents to insure correct assembly.After installation, confirm proper fit.

WRONGOKAYSeal

OKAY WRONG2. Plug welding should be donewith a MIG (Metal Inert Gas)welder. Do not gas weld orbraze panels at areas otherthan specified.

Safety Glass

BodyMeasurementDiagrams

SPOT WELDING PRECAUTIONS1. The shape of the welding

tip point has an effect onthe strength of the weld.

2. Always insure that theseams and welding tip arefree of paint.

SPOT WELD LOCATIONSTry to avoid welding overprevious spots.

OldSpot Locations

New SpotLocations

Tip Cutter

INTRODUCTIONIN-8

Thickness ofwelded portion Size of plug hole

1.0 (0.04) under 5 (0.20) over1.0 (0.04) over 6.5 (0.26) over

REFERENCE: mm (in.)

PREPARATION FOR INSTALLATION

SPOT WELD POINTS APPLICATION OF WELDTHROUGH PRIMER

Less than3 mm

When welding panels with acombined thickness of over 3mm (0.12 in.), use a MIG(Metal Inert Gas) welder forplug welding.NOTE: Spot welding willnot provide sufficient dura-bility for panels over 3 mm(0.12 in.) thick.

For treatmentagainst corrosion,remove the paintfrom the portion ofthe new part andbody to be welded,and apply weldthrough primer.

Air Saw

WRONG

20 30 mm Puncher

Overlap

ROUGH CUTTING OF JOINTSFor joint areas, rough cut the new part, leaving20 30 mm (0.79 1.18 in.)overlap.

MAKING HOLES FOR PLUG WELDINGFor areas where a spot welder cannothe used, use a puncher or drill to makeholes for plug welding.

INTRODUCTION IN-9

ANTICORROSIVE TREATMENT

When replacing body panels, always apply body sealer, antirust treatment or undercoating according tothe requirements of your country.

CHASSIS RUSTPROOFINGAntirust treatment for weld-ing spots or inside brazedareas (torque box).

BODY SEALERApply body sealer to therequired areas.

NozzleTubeType

Air Gun

CartridgeType

UNDERCOATINGAntirust treatment for underbody weldingspots and wheel housings.

Spray GunUndercoating(Water base)

Undercoating(Oil base)

INTRODUCTIONIN-10

IN0088IN0089

SUPPORT POSITION

PANTOGRAPH JACK POSITION

Front Center of front suspension crossmember. . . . . . . . . Rear Center of differential carrier. . . . . . . . . .

JACK POSITION

Safety stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front

VEHICLE LIFT AND SUPPORT LOCATIONS

INTRODUCTION IN-11

Assy, assy Assembly, assembly

Subassy Subassembly

Ex. Except

in. Inch

IRS Independent Rear Suspension

4link 4link Rear Suspension

MIG Metal Inert Gas

M/Y Model Year

OPN Operation

SP Spot Weld (Resistance Spot Weld)

w/ With

w/o Without

FR Front

RR Rear

RH Righthand

RHD Righthand Drive

LH Lefthand

LHD Lefthand Drive

ABBREVIATIONS USED IN THIS MANUALFor convenience, the following abbreviations are used in thismanual.

INTRODUCTIONIN-12

AirpoweredDrill

For separating spot welds and makingholes in the body.

ElectricpoweredDrill

For separating spot welds and makingholes in the body.

Spot Cutter

For separating spot welds.

AirpoweredCutter

For cutting panels.

AirpoweredChuck Grinder

For separating spot and plug weldsand grinding off traces of plug welds.

Tracking Gauge

For measuring body dimensions

Frame CenteringGauge

When 3 or 4 are used together, measure-ments of twists, bends or warps in thebody and frame are possible.

MEASURING INSTRUMENTS

SEPARATING TOOLS

TOOLS AND EQUIPMENTTE-2

AirpoweredChisel

For rough cutting and rough flatteningof panels.

Hammer Tool

Flat Chisel

Panel Cutter

For rough flattening in hardtoreachareas.

For separating spot welds.

For rough cutting of panels.

AirpoweredSaw

For rough cutting of pillars, rockerpanels, etc.

AirpoweredSaw


Hacksaw


SEPARATING TOOLS (Contd)

TOOLS AND EQUIPMENT TE-3

Seat Cover

For protecting the seats from weldingsparks, etc.

Glass Cover

For protecting the glass from weldingsparks, etc.

Vise GripWrench

For temporary installation of panels andholding of portions to be welded.

Flanging Tool

For making flanges in overlappingpanels.

Hemming Tool

For hemming door outer panels, etc.

Hole Punch

For making holes for MIG plug welding.

INSTALLATION ASSISTANCE TOOLS

BODY PROTECTORS


MIG Welder(Metal Inert Gas)

For panel welding.

Spot Welder

For panel welding.

Gas Welder TorchGas Cutter Torch

For rough cutting of panels,members, etc.

Acetylene GasTorch

For soldering and peeling ofpaint.

StraighteningMachine

For straightening distortedpanels.

PanelExtractor

For extraction of closedinpanels.

WELDING INSTRUMENTS


AirpoweredDisc Grinder

For grinding plug welds, butt weldsand door hems.

ElectricpoweredDisc Sander

For grinding plug welds, butt weldsand door hems.

Belt Sander

For removing paint around weldareas.

DoubleactionSander

For rough grinding and polishing, andfeather edging.

Body Pullers

For straightening lightly damaged panels.

LIGHT BODY REPAIR TOOLS

GRINDING AND POLISHING TOOLS


StraightlineSander

For rough polishing of panel putty.

AirpoweredOrbital Sander

For removing putty over a wide area, re-surfacing and refinishing.

AirpoweredDisc Sander

For peeling paint.

File Holder

For paint removal.

Flexible FileHolder

For correction of soldering spotsand resurfacing of panels.

Surforrn Tool

For rough finishing of panels.

GRINDING AND POLISHING TOOLS (Contd)


Master Gauge

Plate Looseness

Twodimensionaldistance

CentertocenterHorizontal distance inforward/rearward

Wrong Correct

GENERAL INFORMATION1. BASIC DIMENSIONS

(a) There are two types of dimensions in the diagram.(Threedimensional distance)

Straightline distance between the centers of twomeasuring points.

(Twodimensional distance) Horizontal distance in forward/rearward between

the centers of two measuring points.

The height from an imaginary standard line.

(b) In cases in which only one dimension is given, leftand right are symmetrical.

(c) The dimensions in the following drawing indicateactual distance. Therefore, please use the dimen-sions as a reference.

2. MEASURING(a) Basically, all measurements are to be done with a

tracking gauge. For portions where it is not possibleto use a tracking gauge, a tape measure should beused.

(b) Use only a tracking gauge that has no looseness inthe body, measuring plate, or pointers.

HINT:1. The height of the left and right pointers must be equal.

2. Always calibrate the tracking gauge before measuring orafter adjusting the pointer height.

3. Take care not to drop the tracking gauge or otherwiseshock it.

4. Confirm that the pointers are securely in the holes.

(c) When using a tape measure, avoid twists andbends in the tape.

(d) When tracking a diagonal measurement from thefront spring support inner hole to the suspensionmember upper rear installation hole, measurealong the front spring support panel surface.

Pointer

Centertocenterstraightlinedistance

Vertical distancein lower surface

Vertical distancein center

Body Looseness

PointerPointer Looseness

Threedimensionaldistance

Imaginary Standard Line

Front Suspension Member Rear SideUpper Installation Hole

Along BodySurface

Front Spring Support Inner Hole

Tape Measure

BODY DIMENSIONSDI-2

mm (in.)

ENGINE COMPARTMENT

Symbol Nomenclature Hole dia.

BO1788

A, a Front fender installation nutfront 8 (0.31)B, b Front spring support holerear 11 (0.43)

C, c Front fender installation nutrear 8 (0.31)D Cowl top panel center mark

E, e Front side member standard hole 15 (0.59)

F, f Suspension member rear installation holeupper 17 (0.67)G, g Retractable light bracket installation nutupper 11 (0.43)H, h Radiator seal installation holelower 7 (0.28)I, i Front fonder aide installation hole 8 (0.31)

J, j Cowl top panel standard hole 10 (0.39)K Hood lock support brace installation nut 7 (0.28)

BODY DIMENSION DRAWINGS

BODY DIMENSIONS DI-3

mm (in.)

Front

X, x Point

LUGGAGE COMPARTMENT

Symbol Nomenclature Hole dia.

BO1790

V Back door opening frame center mark 2 (0.08)W, w Rear suspension spring support holeinner 9 (0.35)X, x Rear floor pan bumper installation holefront 40 (1.57)

BODY DIMENSIONS DI-3

BO

1789

Wheel base 2,595 (102.17)

ImaginaryStandardline

UN

DE

R B

OD

Y

mm (in)

Hole dia.

10 (0.39)

19 (0.75)

18 (0.71)

2518(0.980.71)

18 (0.71)

Nomenclature

Front floor No. 2 reinforcement standard hole

Suspension member front installation holeouter

Center floor side member standard holeSuspension member rear installation hole

Rear floor side member standard hole

Symbol

Q,q

R, r

S, s

T, t

U, u

Hole dia15 (0.59)

1715 (0.670.59)

11 (0.43)

17 (0.67)

17 (0.67)

10 (0.39)

Nomenclature

Front side member bumper front installation holeLower

Front side member bumper front installation holeLowerStabilizer front installation nut

Suspension member front installation holelower

Suspension member rear installation holelower

Front floor under reinforcement standard hole

Symbol

LI

M, m

N, n

O,o

P, p

BO

DY

DIM

EN

SIO

NS

DI-3

mm in.2 0.087 0.28

10 0.39

l0

l0

l0

2R

Center Mark

STANDARD BODY MARKS

LIFTBACK

Assembly Mark

Center Mark(7)

Center Mark

Assembly MarkAssembly Mark


l0

BODY PANEL CONSTRUCTIONCN-2

Door Side ImpactProtection Beam(USA, Canada, Saudi Arabia andAustralia)Front Bumper Reinforcement

Front Apron to CowlSide Upper Member

Front BodyOuter Pillar

Front side Member

Front Floor UnderReinforcement

Front CrossmemberNo. 2 Reinforcement

Rear BumperReinforcement

Belt AnchorReinforcement

Rear FloorSide Member

Rear SuspensionSpring Support

Front SpringSupport Plate

Belt Anchor to RoofSide Inner Reinforcement

Cowl Top toApron Brace

Quarter Pillar InnerReinforcement

Back Door HingeReinforcement

Quarter WheelHousing No. 1 Gusset

Front Body Pillar UpperInner Reinforcement

Hood StopperReinforcement

Back Door LowerOuter Panel

Engine Hood PanelBack Door UpperOuter Panel

The handling of HSS is the same as for mild steel, but the following should be observed.

HIGHSTRENGTH STEEL (HSS) PARTSGenerally, HighStrength Steel (HSS) is that which has an intensity value of at least 35 kg f/mm2, anddistinguished from mild steel.

1. Panel Hammering; Because HSS is thinner than mild steel, care should be taken to avoid warpingduring hammering operations.

2. Removing Stop Welds: Because HSS is tougher than mild steel, damage will occur more easily to aregular drill. Therefore, an HSS Spot Cutter is recommended.Also, use a hightorque drill at low speed, and supply grinding oil to the drill during use.

3. Panel Welding: Panel welding procedures for HSS are exactly the same as for mild steel. Plugwelding should be done with a MIG (Metal Inert Gas) welder. Do not gas weld or braze panels atareas other than specified.

BODY PANEL CONSTRUCTION CN-3

FRONT CROSSMEMBER (ASSY)

REMOVAL

BODY PANEL REPLACEMENTRE-2

INSTALLATION

1. Temporarily installing the new part and measureeach part in accordance with the body dimen-sion diagram.

BODY PANEL REPLACEMENT RE-3

RADIATOR SUPPORT (ASSY)

Cut the weld points from the back side.

REMOVAL


INSTALLATION

Assembly Mark

1. Temporarily install the new part with the assemblymark and measure each part in accordance withthe body dimension diagram.


RADIATOR UPPER SUPPORT (ASSY)

REMOVAL


NOTE: Install the new panel with the hood locksupport.

INSTALLATION

1. Temporarily install the new part and measureeach part in accordance with the body dimen-sion diagram.


FRONT FENDER APRON (ASSY)

REMOVAL


INSTALLATION

Assembly Mark

1. Determine the installation position of the newpart by the assembly mark.

2. Measurements must be accurate with the bodydimension diagram, as this effects the frontwheel alignment.

NOTE: The position of the front spring supporthole is very important3. Check the fit of the front fender and hood.


FRONT FENDER APRON (CUTH)

REMOVAL

Rough Cut

1. After removing the spot welds, rough cut thefront fender apron shown above.


INSTALLATIONCut for supply part

Cut Location

Cut Location

1. Cut the supply part shown above.


FRONT SIDE MEMBER (ASSY)

REMOVAL


NOTE: Make sure each measurement is correct,as this part effects the front wheel alignment.

INSTALLATION

Assembly Mark

Front Side Member Plate



mm in.15 0.5920 0.7960 2.36

FRONT SIDE MEMBER (CUTP)

REMOVAL

Standard Hole (15)

Cut LocationCut Location

Standard Hole (15)

60 mm

20 mm

NOTE: Be careful not to damage thereinforcement when cutting the sidemember.

[Ex. USA and Canada][USA and Canada]

1. Before cutting the side member, remove thebattery carrier support. (LH only)

2. Cut the front side member as shown above.NOTE: Be careful not to damage the reinforce-ment when cutting the side member.


mm in.70 2.76

20 mm

[Ex. USA and Canada][USA and Canada]

Cut LocationReinforcement Reinforcement

70 mm

Cut Location

Remove the remaining reinforcement fromthe supply part.

NOTE: Cut the front side member and the rein-forcement at the same place.

2. Remove the remaining reinforcement from thesupply part.

INSTALLATION

Cut for supply part

[USA and Canada]

Butt Weld

Butt Weld

[Ex. USA and Canada]

1. Cut the supply part shown above. 3. Temporarily install the new member, measureeach part in accordance with the body dimen-sion diagram.

4. After installing the new member, install the frontside member plate.(See page RE13)

5. After installing the new member, install the bat-tery carrier support. (LH only)


COWL TOP SIDE PANEL (ASSY)

REMOVAL

Cut with disc sander etc.


mm in.20 0.79

INSTALLATION


Tack Weld (20 mm each)

1. Determine the installation position of the newpart by the assembly mark.

2. Temporarily installing the new part and measureeach part in accordance with the body dimen-sion diagram.


mm in.150 5.91

FRONT BODY PILLAR (CUT)

REMOVAL

150 mm or more [Cut and Join Location]Cut and JoinLocation

Cut With DiscSander etc.

1. Cut and join the front body pillar at the locationshown above.

NOTE:1) As shown above, cut and join the front body

pillar outer and inner panels at a positionshifted about 50 mm (1.97 in.).

2. Remove the remaining roof drip channel frombody side.


mm in.20 0.79

790 31.10791 31.14946 37.24

1,162 45.751,402 55.201,407 55.39

INSTALLATION

Butt Weld

[Reference]

(mm)

Tack Weld(20 mm each)

1. Temporarily install the new part and check the fitof the front door, front fender, hood and wind-shield glass.


mm in.140 5.51

OUTER ROCKER PANEL (CUT)

REMOVAL

140 mm

Cut and Join Location


1. Cut and join the outer panel at the area as showabove.


INSTALLATION

Butt Weld

1. Temporarily install the new panel and check thefit for the front door and front fender.

2. There will be less warp if the cut edge (30 40mm or 1.18 1.57 in.) is adhered to the match-ing part before welding.

NOTE: Scrape off the film on the cut edge and ap-ply weldthrough primer to adhere the matchingpart.


ROOF PANEL (ASSY)

REMOVAL

Arc Brazing(both sides)

Braze (both sides)

Braze (both sides)

1. Heat the brazed area of the front pillar andscrape off the brazing with a wire brush.

NOTE: Be careful not to overheat the pillar.2. Cut off the roof panel tip at the quarter panel are

brazing connection with a cut grinder.


2. Braze the front body pillar connection.NOTE: Before performing these operations,place a wet rag on the roof panel to protect itfrom damage.

INSTALLATION

Body Sealer (6 points)

Braze (both sides)

Body Sealer (8 points)

Braze (both sides)

1. Before temporarily installing the new part,apply body sealer to the windshield headerpanel, roof panel center reinforcement andback window opening frame.

NOTE:1) Apply just enough sealer for the new part

to make contact.

2) For other sealing points, refer to sectionSU.


FRONT DOOR OUTER PANEL (ASSY)

REMOVAL

Hemming Location

Heat slightly(USA, Canada, Saudi Arabia andAustralia)

Disc Sander

1. Grind out the hemming location, and remove theouter panel.

2. Slightly heating the outer panel will soften thesealer and make removal easier. (USA, Canada,Saudi Arabia and Australia).


mm in.10 0.39

3. Bend the flange hem approx. 30 with a hammerand dolly. Then use a hemming tool.

NOTE:1) Perform hemming in three steps, being care-

ful not to warp the panel.

2) It a hemming tool cannot be used, hem with ahammer and dolly.

INSTALLATION


About 10 mm

Do not close thedrain hole.Body Sealer Body Sealer (6 points)

(USA, Canada, Saudi Arabia andAustralia)

Cloth Tape

30

Hemming Tool

1. Before temporarily installing the new part, coatthe back side of the new panel with body sealer.

NOTE:1) Coat evenly about 10 mm (0.39 in.) from the

flange and 3 mm (0.12 in.) in diameter


3) Determine the position for the new panel bythe assembly marks.


mm in.87 3.43

200 7.87

QUARTER PANEL (CUT)

REMOVALCut and Join Location

Cut and Join Location200 mm

80 mm


Front

Braze

Rear

1. Cut and join the quarter panel as shown above.


mm in.5 0.20

NOTE:1) Apply sealer approx. 5 mm (0.20 in.) from the

flange, avoiding any oozing.

2) Apply evenly, approx. 3 4 mm (0.120.16in.) in diameter.


INSTALLATION

Butt Weld

Butt Weld

Body Sealer

Braze

Body Sealer

About 5 mm

1. Before temporarily installing the new part,apply body sealer to the wheel arch portion.

2. Temporarily install the new part and check the fitof the front door, luggage compartment door andrear combination lamp.


QUARTER PANEL (CUTP)

REMOVAL

About 335 mm

Cut and JointLocation

Cut and JointLocation

* This section is a cut and join location only.Refer to RE26 for weld points.

1. Cut on the line shown above.


INSTALLATION

Butt Weld

Body SealerAfter butt welding,apply body sealer

ButtWeld

Body Sealer

About 5 mm

* This section is a cut and join location only.Refer to RE27 for weld points.

1. Before cutting the overlap areas, check the fitfor the luggage compartment door and rearcombination lamp.

2. Before welding, apply body sealer from insideof the vehicle.

NOTE:1) Do not apply body sealer to the weld seams

before welding as the sealer will melt, re-sulting in a bad seal and a bad weld.


3. Surface finish the weld seam from the insidealso.

NOTE: Be careful not to grind off to much weld asit will result in loss of durability.


BODY LOWER BACK PANEL (ASSY)

REMOVAL

Braze (both sides)

(both sides)

(both sides)


INSTALLATION

Braze (both sides)

(both sides)

(both sides)

1. Temporarily install the new part and check thefit of the back door and rear combination lamp.


QUARTER WHEEL HOUSING OUTER PANEL (ASSY)

REMOVAL

Roof Side Inner toWheel Housing Brace

1. Before removing the quarter wheel housing out-er panel, remove the roof side inner to wheelhousing brace.


INSTALLATION


1. Determine the position of the new part by theassembly marks of the inner and outer panels.

2. Before welding the new part, temporarily installthe quarter panel and check the fit.


REAR FLOOR PAN (CUT)

REMOVAL

Cut Location

(RH)(LH)

1. Cut and join the rear floor pan shown above.

2. Avoid the rear floor side member.

3. Since each bracket is supplied separated,remove the brackets if reusing.


Body Sealer

Adhere

INSTALLATIONCut Locations

Plug Weld

New Part

NOTE: Be sure the portion to be welded are alignand not loose.5. Coat the overlapping opening portion from the

both sides with body sealer.

1. Cut the new panel shown above.

2. Match the bracket to the new part location(dent marks) and install.

3. After temporarily installing the new part,measure each part in accordance with thebody dimension diagram.

4. Plug weld the overlapping portion of the newpart.


REAR FLOOR SIDE MEMBER (ASSY)

REMOVAL

1. Before removing the rear floor side member,remove the rear floor pan.


INSTALLATION



CENTER FLOOR SIDE MEMBER (ASSY)

REMOVAL


INSTALLATION Differential Support MemberMounting Reinforcement

Quarter Wheel Housing No.1 Gusset


Flexible Hose Bracket


CENTER FLOOR NO. 2 CROSSMEMBER (ASSY)

REMOVAL


INSTALLATION


57161

53291C53932

5320953203

53291C

5370253258

53633532575380253202

53287B (RH)53288B (LH)

53205

53723A (RH)53724A (LH)53801

5570153701

55713A (RH)55714A (LH)

53385A (RH)53386A (LH) 53899B

55101

55748A

53301

Code Part Name Code Part Name

5320253203 Radiator Support SubAssy

53723A53724A Front Spring Support Reinforcement

53205 Radiator Upper Support SubAssy 5380153802 Front Fender SubAssy53209 Hood Lock Brace SubAssy

5325753258 Front End Panel Mounting Bracket

53899B Front Fender Panel Support53932 Front End Panel SubAssy

53287B53288B Radiator Support Extension

55101 Dash Panel SubAssy55701 Cowl Panel SubAssy

53291C Radiator Support to Frame Seal 55713A55714A Cowl Top Side Panel53301 Hood SubAssy

53385A53386A Hood Bumper Retainer

55748A Cowl Top Inner to Pillar Brace55748A Cowl Top Inner to Pillar Brace

53633 Hood Lock Control Cable Shield 57161 Front Crossmember

5370153702 Front Fender Apron SubAssy

PART LISTSPL-2

61617A (RH)61618A (LH)

61412

61389A

61346B61711A (RH)61712A (LH)

613676110461769A

61262

61348A

61612

61232

61388A61212

61619A61774A

6154861367 61708

61641B (RH)616428 (LH)

61515A61611 61626E

61768B

61633A (RH)61634A (LH)

61231

61103

617076126161619A

61766B6154761211 61675B

61625E

61515A

61411

61345B

61347A

61767B

61773A

61631A (RH)61632A (LH)

61747 (RH)61748C (LH)

61657B (RH)61658B (LH)


6110361104 Front Body Pillar SubAssy

61619A Quarter Panel Reinforcement

61625E61626E Quarter Panel Inner Rear Extension61107

61108 Front Body Outer Pillar SubAssy 61631A61632A Quarter Wheel Housing Outer Panel61211

61212 Roof Side Outer Rail 61633A61634A Quarter Wheel Housing Inner Panel61231

61232 Roof Side Inner Rail 61641B61642B Quarter Wheel Housing Gusset61261

61262 Roof Drip Channel 61657B61658B Quarter Panel End Lower Housing61345B

61346B Center Body Inner Lower Pillar61675B

Rear Suspension Spring SupportReinforcement61347A

61348A Belt Anchor to Center Pillar Reinforcement 6170761708 Quarter Inner Panel SubAssy

61367 Belt Anchor to Center Pillar LowerReinforcement 61711A61712A Roof Side Outer Reinforcement61388A

61389A Center Body Pillar End Plate 6174761748C Roof Side Inner to Wheel Housing Brace61411

61412 Rocker Outer Panel 61766B61767B

Roof Side Inner to Wheel Housing BraceReinforcement61515A Quarter Lock Pillar Extension

6154761548 Quarter Pillar Inner Reinforcement 61768B

Belt Anchor to Roof Side Inner RearReinforcement

6161161612 Quarter Panel

61769A Seat Belt Anchor No. 2 Reinforcement

61773A61774A Back Door Opening Lower Patch61617A

61618A Quarter Inner Rear Panel

PART LISTS PL-3

5725757106A57418

5725757402

57102 5168157426

5707257044 5780557805 58149A57649

5710157105A57425 58273B 57402

58272B57071 LHD5704357632B 57436

57631B57401 57475 5774757435 5760257648 5760158139A

57523

574645168157737

57475

5745157407

57405A57463

58029A58142

58208F58101F 58101F

57467A58264B 58207F

58111 5817357469A

58212C581427466A

57673 58275C

583465817357468A

58367

58314F57457C

58101A

58109A58193 57465A

58311

58313F

58311E5818358102A

58364B5830558183 58364B58307

58208

57656A

57417

PART LISTSPL-4


51681 Flexible Hose Bracket 57656A Exhaust Pipe Mounting No. 1 Bracket

5704357044

Front Side Member Rear Reinforcement57673 Rear Seat Back Hinge Mounting Bracket5773757747

Differential Support Member MountingReinforcement57071

57072 Torque Rod Rear Box SubAssy 57805 Belt Anchor Reinforcement SubAssy5710157102 Front Side Member SubAssy

58029A Parking Brake Cable No. 1 Clamp58101A Transmission Auxiliary Cover

57105A57106A Front Side Member Plate SubAssy.

58101F Mounting Floor No. 1 Bracket58102A Front Floor Reinforcement SubAssy

57257 Engine Rear Support Member Bracket 58109A Parking Brake Retainer SubAssy5740157402 Main Floor Side Member SubAssy

58111 Front Floor Pan

58139A58149A Front Floor Side Rear Plate57405A Center Floor No. 2 Crossmember SubAssy

57407 Center Floor No. 1 Crossmember SubAssy58142

Floor Side Member to Floor PanReinforcement57417

57418 Front Floor Under Reinforcement 58173 Front Floor Stone Deflector5742557426 Front Floor No. 2 Reinforcement

58183 Front Seat Mounting Inside Bracket58193 Instrument Panel Brace Mounting Bracket

5743557436 Center Floor Side Member

58207F58208F Parking Brake Cable Clamp SubAssy

57451 Front Floor Crossmember 58208 Center Floor Pan57457C Front Outside Mounting Front Bracket 58212C Center Floor Front Pan57463 Center Floor No. 3 Crossmember 58264B Parking Bake Cable Guide No. 1 Bracket57464 Center Floor Crossmember Strength 58272B Belt Anchor to Floor Pan No. 4 Reinforcement57465A57466A Center Floor Crossmember Rear Gusset

58273B Belt Anchor to Floor Pan No. 5 Reinforcement58275C Wire Harness Protector Bracket

57467A Front Seat Outside Mounting Front Bracket 58305 Spare Wheel Clam Bracket SubAssy57468A57469A Front Seat Outside Rear Bracket

58307 Body Lower Back Panel SubAssy58311E Rear Floor Service Hole Cover

57475 Front Floor Crossmember Plate 58311 Rear Floor Pan57523 Center Floor Crossmember Brace 58313F

58314F Rear Floor Pan to Quarter Panel Extension5760157602 Rear Floor Side Member SubAssy 58364 Rear Floor Heat Insulator Bracket57631B57632B Rear Floor Side Member Front Reinforcement

58364B Fuel Tank Support Bracket58367 Fuel Tube Clamp Bracket

5764857649 Quarter Wheel Housing No. 1 Gusset

PART LISTS PL-5

67001 (RH)67002 (LH)

61111 (RH)61112 (LH)

67005

63102A

63104

63105A

63111


63102A Windshield Header Panel SubAssy 6700167002 Front Door Panel SubAssy63104 Roof Panel Center Reinforcement SubAssy

63105A Back Door Opening Frame SubAssy 67005 Back Door Panel SubAssy

63111 Roof Panel 6711167112 Front Door Outer Panel

PART LISTSPL-6

CodeMaterialName

Heat *Resisting

TemperatureC (F)

Resistance ToAlcohol or Gasoline Notes

AAS

AcrylonitrileAcrylic RubberStyreneResin

80(176)

Alcohol is harmless if applied onlyfor short time in small amounts(ex., quick wiping to removegrease).

Avoid gasoline andorganic or aromaticsolvents.

ABS

AcrylonitrileButadieneStyreneResin

80(176)



AES

AcrylonitrileEthylene RubberStyreneResin

80(176)



EPDMEthylenePropyleneRubber

100(212)

Alcohol is harmless.Gasoline is harmless if applied onlyfor short time in small amounts.

Most solvents are harm-less but avoid dipping ingasoline, solvents, etc.

PAPolyamide(Nylon)

80(176)

Alcohol and gasoline areharmless. Avoid battery acid.

PC Poiycarbonate120

(248) Alcohol is harmless.Avoid gasoline, brakefluid, wax, wax removersand organic solvents.

PE Polyethylene80

(176)Alcohol and gasoline areharmless.

Most solvents areharmless.

POMPolyoxymethylene(Polyacetal)

100(212)

Alcohol and gasoline areharmless.


HANDLING PRECAUTIONS1. The repair procedure for plastic body parts must conform with the type of plastic material.

2. Plastic body parts are identified by the codes in the following chart.

3. When repairing metal body parts adjoining plastic body parts (by brazing, frame cutting, welding, paint-ing, etc.), consideration must given to the property of the plastic.

* Temperature higher than those listed here may result in material deformation during repair.

PLASTIC BODY PARTSPP-2

Code MaterialName

Heat *Resisting

TemperatureC (F)

Resistance ToAlcohol or Gasoline Notes

PP Polypropylene 80(176)Alcohol and gasoline areharmless.


PPOModifiedPolyphenyleneOxide

100(212) Alcohol is harmless.

Gasoline is harmless if applied only for quick wiping to remove grease.

PS Polystyrene 60(140)

Alcohol and gasoline are harm-less if applied only for short timein small amounts.

Avoid dipping or immersing in alcohol,gasoline, solvents, etc.

PURThermosettingPolyurethane

80(176)

Alcohol is harmless if applied only forvery short time in small amounts (ex.,quick wiping to remove grease).


PVCPolyvinylchloride(Vinyl)

80(176)

Alcohol and gasoline are harmless ifapplied only for short time in smallamounts (ex., quick wiping to removegrease).


PMMAPolymethylMethacrylate

80(176)

Alcohol is harmless if applied onlyfor short time in small amounts.


SANStyreneAcrylonitrileResin

80(176)



SMCSheetMoldingCompound

180(356)

Alcohol and gasoline areharmless. Avoid alkali

TPOThermoplasticOlefine

80(176)

Alcohol is harmless.Gasoline is harmless if applied onlyfor short time in small amounts.

Most solvents are harm-less but avoid dipping ingasoline, solvents, etc.

TPUThermoplasticPolyurethane

80(176)

Alcohol is harmless if applied only forvery short time in small amounts (ex.,quick wiping to remove grease).


* Temperature higher than those listed here may result in material deformation during repair.

PLASTIC BODY PARTS PP-3

LOCATION OF PLASTIC BODY PARTS

Fuel Tank Filler Protector (PE)

Safety Pad (PVC/PUR)Roof Headlining(PVC/PUR)

Washer Nozzle (PA)Quarter VentilationLouver (ABS)

Rear Spoiler (SMC)Front Facia Cover (PUR)

Fan Shroud (PP)

Washer Jar (PP)

*1 Rear SideMarker Lamp(PMMA/ ABS)

Room Pressure ReliefValve (PP)

Radiator Grill (ABS)Fuel Tank No. 1 Protector(PE)

Door Scuff Plate (PP)Radiator GrillLower (PP)

Fender Liner (PE)Front Turn SignalLamp (PMMA/PP) *1 Side Marker Lamp (PMMA/ABS)

*2 Side Turn Signal Lamp (SAN/ABS)

Front Bumper Cover (PUR)

Front Spoiler Cover (PUR)

NOTE: Resin material differs with model./ Made up of 2 or more kinds of materials.*1 USA and Canada*2 Except USA and Canada


Roof Side Trim Garnish (ABS/PVC)

Front Body Pillar Garnish (PUR)

Roof Side Rail Front Garnish (PVC)

Font Door Trim Board (PVC/PP)

Roof Headlining Rear Trim (PVC)

Speaker Door Grill (ABS) Quarter Inside Trim Board(PVC/PP)

Cowl Side Trim Board (PP) Back Door Trim Board (PP)

Headlight Door(AAS)

Speaker Box (PP)

Outer Rear View Mirror(ABS/TPU)

Radiator Reserve Tank (PP)

Speaker Box (PP)Headlight Door Protector (PP)

NOTE: Resin material differs with model./ Made up of 2 or more kinds of materials.*1 USA and Canada*2 Except USA and Canada

PLASTIC BODY PARTS PP-5

Deck Trim Side Jack Cover (PP)

Deck Side Trim Panel (PP)

Cooler Unit (PP)Rear Speaker Grill (PP/ABS)Heater Unit (PP)

Heater Blower (PP)Deck Trim Rear Cover (PP)

Deck Trim Side ServiceHole Cover (PP)

Rear CombinationLamp Service Cover(PP)

Font Fender MudGuard (PUR)

Outside Moudling(PVC/PUR)

License Pate Lamp(PMMA/PC)

Lower Back Finish PanelHole Cover (ABS)Side Mud Guard (PUR)

Rear Bumper Cover (PUR)

*1 Rear Marker Lamp (PMMA/ABS) Rear Combination Lamp (PMMA/AES)

Quarter Panel Mud Guard (PUR)

NOTE: Resin material differs with model./ Made up of 2 or more kinds of materials.*1 USA and Canada


NOTE:1. Prior to applying body sealer, clean the area with a rag soaked in white gasoline.

2. If weldthrough primer was used, first wipe off any excess with thinner, and coat with anticorrosion primer before applying body sealer.

3. Wipe off any excess body sealer with a rag soaked in white gasoline.

BODY PANEL SEALING AREASFor waterproofing and anticorrosion measures, always apply body sealer to the body panel seams andhems of the doors, hood, etc.

Flat SurfacingFlat Surfacing

BODY PANEL SEALING AND UNDERCOATINGSU-2

After installing the plug hole, apply sealer.

Flat Surfacing

BODY PANEL SEALING AND UNDERCOATING SU-3

Flat Surfacing


Hood

Front Door Panel

Back Door Panel

Do not close the drain hole.

Flat surfacing

Fuel Inlet Box Fuel Inlet Box Cover

BODY PANEL SEALING AND UNDERCOATING SU-5

BODY PANEL UNDERCOATING AREASTo prevent corrosion and protect the body from damage by flying stones, always apply undercoating to thewelded seams and wheel housings after chassis, under body or panel repair.NOTE:1. First wipe off any dirt, grease or oil with white gasoline.

2. Cover the surrounding areas with masking paper to avoid coating unnecessary areas. If otherareas are accidently coated, wipe off the coating immediately.

3. Do not coat parts which become hot, such as the tail pipe, or moving parts, such as the propel-ler shaft.

4. Besides the locations described below, apply undercoating to all weld points under the body toinsure corrosion prevention.

5. Be sure to seal the edge of the flange of the member and bracket with undercoating.

REFERENCE: Referring to the notes above, undercoating should be applied according to the specificationsfor your country.


A70 Chassis Collision Repair Manual.pdf

Documents

Transcript of A70 Chassis Collision Repair Manual.pdf