a
description
Transcript of a
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
www.huawei.com
Internal
WCDMA NodeB Operation and Maintenance
NodeBV200R011
WRAN Training Team
HUAWEI TECHNOLOGIES CO., LTD. Page 2All rights reserved
NodeB OM is used to manage, monitor and
maintain the software, hardware and
configuration.
The NodeB supports two OM platforms:
LMT and M2000.
The NodeB provides OM functions such as
equipment, software and alarm
management.
HUAWEI TECHNOLOGIES CO., LTD. Page 3All rights reserved
Upon completion of this course, you will be able to:
Know the structure of NodeB operation and
maintenance system
Master NodeB operation and maintenance f
unctions
Manage NodeB routine maintenance
HUAWEI TECHNOLOGIES CO., LTD. Page 4All rights reserved
《 NodeB LMT User Guide》 《 NodeB Site Maintenance Guide》 《 NodeB System Commissioning Guid
e》
HUAWEI TECHNOLOGIES CO., LTD. Page 5All rights reserved
Chapter 1 Overview of NodeB O&MChapter 1 Overview of NodeB O&M
Chapter 2 FunctionChapter 2 Function of NodeB O&Mof NodeB O&M
Chapter 3 NodeB Routine MaintenanceChapter 3 NodeB Routine Maintenance
HUAWEI TECHNOLOGIES CO., LTD. Page 6All rights reserved
Abbreviations
EPLD Erasable Programmable logic Device
LMT Local Maintenance Terminal
HUAWEI TECHNOLOGIES CO., LTD. Page 7All rights reserved
Operation and Maintenance System
O&M mode Description
Local maintenance The LMT is connected to the NodeB through the Ethernet port on the WMPT, as the L
MT1 and LMT2 . Huawei NodeB default local maintenance IP address: 17.21.2.15
Remote maintenance The LMT is connected to the NodeB through the M2000 Server and the IP over ATM (I
PoA) channel between the NodeB and the RNC, as the LMT5 and LMT6
Reverse maintenance LMT1 to maintence the NodeB2
RNC
NodeB
NodeB
IP over Ethernet
IP over Ethernet
IPoA
IPoA
Internet/DDN
PSTN
Modem
Modem
iManager M2000LMT6
LMT5
LMT4
LMT1
LMT2
HUAWEI TECHNOLOGIES CO., LTD. Page 8All rights reserved
NodeB LMT
The NodeB LMT is mainly used for NodeB commissioning, routine mainten
ance, and troubleshooting
Overview of Operation and Maintenance
LMT provides the following functions:
GUI
MML commands
Alarm management, equipment management, cell management, software
management, file management, message tracing, and real-time monitoring
HUAWEI TECHNOLOGIES CO., LTD. Page 9All rights reserved
LMT Window
Overview of Operation and Maintenance
1
2
3
HUAWEI TECHNOLOGIES CO., LTD. Page 10All rights reserved
The MML command format is Action + Object
MML Commands Introduction
Action Meaning Example
ACT Activate ACT SOTWARE
ADD Add ADD BRD
DSP Display dynamic information DSP BRD
LST List LST ALMCFG
MOD Modify MOD OMCH
RMV Remove RMV BRD
RST Reset RST BRD
SET Set SET CLKMODE
STP Stop STP CLKTST
STR Start STR CLKTST
BLK Block BLK LOCELL
UBL Unblock UBL LOCELL
DLD Download DLD SOTWARE
ULD Upload ULD CFGFILE
HUAWEI TECHNOLOGIES CO., LTD. Page 11All rights reserved
Chapter 1 Overview of NodeB O&MChapter 1 Overview of NodeB O&M
Chapter 2 Function of NodeB O&MChapter 2 Function of NodeB O&M
Chapter 3 NodeB Routine MaintenanceChapter 3 NodeB Routine Maintenance
HUAWEI TECHNOLOGIES CO., LTD. Page 12All rights reserved
Alarm Management
Equipment Management
Cell Management
Software Management
File Management
Trace Management
Real time monitor
Function of NodeB Operation and Maintenance
HUAWEI TECHNOLOGIES CO., LTD. Page 13All rights reserved
Alarm types:
Fault Alarm
−The alarms generated in case of hardware equipment faults or major
function failures. After the fault has been removed ,the system will
report a cleared alarm. One clear alarm corresponds to one fault alarm.Event Alarm
−The accidental alarms indicating that the system is in alarm state for a
while. There is no cleared alarm for event alarms. Classified by network management
Power system
Environment system
Signaling system
Trunk system
Hardware system
Software system
Operating system
Communication system
QoS
Error processing
Alarm Management
HUAWEI TECHNOLOGIES CO., LTD. Page 14All rights reserved
Alarm severity
Critical Alarm
− The critical Alarm has an impact on the service provided by the
system. It requires timely handling
Major Alarm
− The major alarm affect QoS. It requires immediate handling.
Minor Alarm
− The minor alarm does not affect QoS. It requires handling at a
proper time against potential faults.
Warning Alarm
− The warning shows a potential error that may affect service. It
may require handling in some cases.
Alarm Management
HUAWEI TECHNOLOGIES CO., LTD. Page 15All rights reserved
Operations of Alarm
Alarm Management
Browse AlarmIn the LMT window, choose Fault Management > Browse Alarm
Query Alarm Logs LST ALMLOG
Querying Alarm Handling
Suggestions
1. In the Alarm Browse window or
the Query Alarm Log window,
double-click an alarm.
2. Click Help in Alarm Detailed
Information dialog box.
Query Alarm Configuration LST ALMCFG
Shielding a NodeB Alarm SET ALMSHLD
HUAWEI TECHNOLOGIES CO., LTD. Page 16All rights reserved
Operating the NodeB device panel
Start device panel:
−In the navigation pane of
the LMT window, click the
Maintenance tab.
−Double-click Topology
Management > Main
Cabinet. The device panel of
the cabinet is displayed.
Equipment Management
HUAWEI TECHNOLOGIES CO., LTD. Page 17All rights reserved
Operating the NodeB device panel
Displaying the board version
Querying active board alarms
Displaying the board status
Reset the board (not supported by the NCMU/NPMU)
Display CPU usage
Block and unblock a NodeB board
Note:We can right-click one board to choose these functions.
Equipment Management
HUAWEI TECHNOLOGIES CO., LTD. Page 18All rights reserved
Operating the physical topology
Click the Maintenance tab in the navigation pane.
Double-click Topology Management > RRU Physical Topology.
The physical topology window is displayed.
Equipment Management
HUAWEI TECHNOLOGIES CO., LTD. Page 19All rights reserved
Operation on NodeB
Equipment Management
List NodeB Type LST NODEBTYPE
Set Time Zone and Daylight Saving Time SET TZ
Modify NodeB Time MOD TM
Display Bar Code DSP BARCODE
Set SNTP Client Parameters SET SNTPCLTPARA
Reset NodeB RST NODEB
HUAWEI TECHNOLOGIES CO., LTD. Page 20All rights reserved
Operation on Boards
Equipment Management
Display Board Status DSP BRD
Block Board BLK BRD
Unblock Board UBL BRD
Swap Board SWP BRD
Set Subboard SET SUBBRD
Reset Board RST BRD
Querying the CPU Occupancy of a NodeB Board
DSP CPUUSAGE
Querying the E1/T1 Link Status DSP E1T1
HUAWEI TECHNOLOGIES CO., LTD. Page 21All rights reserved
Operation on RRU
Equipment Management
Adding an RRU to the Sector ADD SEC
Modifying the transmission power of an RRU
MOD RRUOFLOCELL
Add RRU Chain or Ring ADD RRUCHAIN
Display RRU Physical Topology DSP RRUPHYTOPO
Display RRU Chain or Ring State DSP RRUCHAINSTATE
Open RRU Emulational Frame
1.Double-click Service > Topology
Management > RRU Physical
Topology
2. Right-click the RRU node.
HUAWEI TECHNOLOGIES CO., LTD. Page 22All rights reserved
Blocking/Unblocking Cell
Blocking cell: BLK LOCELL
− Blocking a cell is used to transfer the service on the cell to a
neighboring cell and then close the Tx channels of the cell, the cell
resources are not available after this operation.
Unblocking cell: UBL LOCELL
− NodeB will open the Tx channels and restore the administration status
of the cell. The cell is in service.
Auditing resource: ADT RES
Use this command to request RNC for audit on the logical resources
between RNC and NodeB.
Note: In this way, you can maintain faulty NodeB without interrupting service
Cell Management
HUAWEI TECHNOLOGIES CO., LTD. Page 23All rights reserved
Types of NodeB Software
BootROM software
NodeB software
Cold patch software
Software Management
Hot patch software
Operation on software
List NE Running Version LST VER
List NE Software Version LST SOFTWARE
Activate Software Version ACT SOFTWARE
Synchronize Software Version SYN SOFTWARE
Display Board Version DSP BRDVER
Download NE Software DLD SOFTWARE
HUAWEI TECHNOLOGIES CO., LTD. Page 24All rights reserved
Software Management
Software Description
BootROM software The BootROM software refers to the software bound with hardware. It provides basic device
drive function and can be started and updated manually.
The BootBOM software is a re-writable storage medium, which is used to store binary data, t
hat is, the machine codes. All the boards on the NodeB have such BootROM software.
The file name of the BootROM software is Firmware.csp.
NodeB software For macro NodeBs, the main board has NodeB software version for the master CPU and slav
e CPU.
The file name of the NodeB software is Software.csp.
Cold patch
software
The NodeB cold patch can upgrade a specific board or module to improve functions or to fix s
ome problems.
The file name of the cold patch is NBPatch.pck.
Hot patch software The NodeB hot patch is also named online patch, which can upgrade the NodeB without inter
rupting its operation. The hot patch is used to improve NodeB functions or to fix some proble
ms.
The file name of the hot patch is NBHPatch.pck.
HUAWEI TECHNOLOGIES CO., LTD. Page 25All rights reserved
Software Management
Upgrade NodeB Software
Using NodeB LMT to upgrade NodeB software
− Click the Maintenance tab in the navigation pane
− Double-click Software Management > Software Update
Using USB to upgrade NodeB software
HUAWEI TECHNOLOGIES CO., LTD. Page 26All rights reserved
Types of the NodeB Files
Data Configuration File Operating Log Main Board Log CAN Log
File Management
Obtaining NodeB Files
Upload the files to the server, then log in to the FTP server to
browse the files. Browse the operation log on the M2000.
Board Log RTWP Routine Test Log Device Archive File
HUAWEI TECHNOLOGIES CO., LTD. Page 27All rights reserved
Download/Backup the NodeB configuration file
Using LMT to download NodeB configuration file−Double-click Software Management > Data Config File Transfer
Use USB to download the NodeB configuration file
File Management
HUAWEI TECHNOLOGIES CO., LTD. Page 28All rights reserved
Upload NodeB Logs to FTP service
Double-click Software Management > Other File Transfer.
File Management
Upload a Device Archive to FTP service
Double-click Software Management > Device Archives Transfer.
HUAWEI TECHNOLOGIES CO., LTD. Page 29All rights reserved
Content of operation
Iub Interface signal Tracing
IP message tracing
SCTP message tracing
ICP tracing
cell tracing
User tracing
Saalink tracing
Note: You can create only one standard interface trace task at a time in
the Operation and Maintenance system. The system creates a message
browse pane for the task.
Tracing Management
HUAWEI TECHNOLOGIES CO., LTD. Page 30All rights reserved
Tracing operation
In the navigation tree of the LMT, double-click Trace Management >
Interface Trace Task >The Tracing function.
Set the parameters. Click OK. The message browse window is displayed.
Tracing Management
HUAWEI TECHNOLOGIES CO., LTD. Page 31All rights reserved
Real Time Management
Collecting the IP clock data
Collecting Statistics About the Traffic on the Iub Interface
Collecting Statistics About the Link-Based Bandwidth
Monitoring the Cell Traffic Throughput
Monitoring the IP Path Performance Statistics
Monitoring the Packet Loss Rate on the IP Layer
Monitoring the Packet Loss Rate on the MP Layer
Querying the resource of a cell
Measuring the RTWP
Monitoring the Output Power of the NodeB
Querying the Resources of a NodeB Board
HUAWEI TECHNOLOGIES CO., LTD. Page 32All rights reserved
Chapter 1 Overview of NodeB O&MChapter 1 Overview of NodeB O&M
Chapter 2 Function of NodeB O&MChapter 2 Function of NodeB O&M
Chapter 3 NodeB Routine MaintenanceChapter 3 NodeB Routine Maintenance
HUAWEI TECHNOLOGIES CO., LTD. Page 33All rights reserved
Purpose of Routine Maintenance
The aim of routine maintenance is to prevent, discover and solve problems in time.
Routine Maintenance Classification
Classification by maintenance method
− Regular maintenance
− Irregular maintenance
Classification by maintenance mode
− Passive maintenance
− Active maintenance
Classification by maintenance period
Routine Management
HUAWEI TECHNOLOGIES CO., LTD. Page 34All rights reserved
Daily Maintenance item Operation
instructions Notes
Check and handle NodeB Active al
arms in real time (daily)
Handle all active
alarms
Check and handle NodeB alarm lo
g
Check Cell Status DSP CELL
All cells should be in
normal or enable
state
Check Trunk Status
DSP IMALNK
DSP IMAGRP
DSP AAL2NODE
DSP AAL2PATH
All links should be in
normal or enable
state
Daily Maintenance Operations
HUAWEI TECHNOLOGIES CO., LTD. Page 35All rights reserved
Weekly
Maintenance
item
Operation instructions Notes
Check boards
status in OMC
Check whether all boards are Logical Available
(select all NodeBs in same version).
Open M2000 Client and use Report Redirection
in right key function to redirect the report to the f
ile.In order to keep report file is clean(Not includ
e other MML result), if the Redirection has been
selected you should first cancel Redirection and
then execute the Report Redirect again.
DSP BRD: CN=MASTER; select all NodeBs in
NE tree
Record the symptoms, causes and handling pro
cess of relevant alarms.
The Logical Available
Status of all boards
that be configured
should be YES.
Weekly Maintenance Operations
HUAWEI TECHNOLOGIES CO., LTD. Page 36All rights reserved
Quarterly
Maintenance
item
Operation instructions Notes
Backup NodeB
data files
Perform full backup after NodeB installation and
upgrade and perform data file backup only
during routine maintenance afterwards.
Mark the backup files
with the date and
version.
Check spare parts
Check the spare parts according to the
registration list. Make sure that the spare parts
are complete and in good order.
Supplement necessary
spare parts.
Send the replaced
spare parts for repair.
Analyze the
running status
and faults of this
NodeB and make
out a plan against
faults
Analyze the faults occurring frequently in this
NodeB to improve routine maintenance in the
future.
Map out the
maintenance of the
next quarterly.
Quarterly Maintenance Operations