ARDEX ENDURA (INDIA) PRIVATE LIMITEDCorporate Office & Regd. Office: Unit No. 406 & 407, Brigade Rubix, No. 20, Yeshwanthapur Hobli, HMT Campus, Bangalore - 560022. Karnataka, INDIA.CIN No: U24233KA1997PTC022383Tel: +91 80 66746500 Fax: +91 80 66746540 Email: customercare@ardexendura.com Visit us: www.ardexendura.com

A 801

Features

Excellent weather resistance

Use for Interior & Exterior

Easy mixing & application

Good bonding strength

Draft Copy : 08-4-14

Ready Mix Plaster

DESCRIPTION

PERFORMANCE

SITE WORK INSTRUCTIONSSURFACE CONSIDERATIONSNew Concrete / Brick / Block Wall:

MIXING

APPLICATION

1.

A 801 is a grey, premixed ready to use cement based mortar for internal & external application, which ensures quality consistency. A 801 is a mixture of graded inert filler, additives and binder.

A 801 can be used for internal & external application to improve the quality of work. It improves permeability and excellent weather resistant. It has strong adhesion with a proper flexibility, able to compensate the temperature difference stress between substrate and the outer coatings.

SURFACE PREPARATIONBefore starting any work ensure that the base is :! Sufficiently flat to permit the specified

flatness of finished plastering, bearing in mind the permissible minimum & maximum thickness of the bedding materials.! Suitable for plastering in the service

condition to which it will be exposed.! Free from efflorescence, laitance, dirt and

other loose material, remove thoroughly with dry brushing.

Before plastering allow walls to dry out by exposure to air, concrete 28 days, brick and block walls 7 days curing time.The surface of the substrate should be sound.

Add A 801 to clean water. Mix thoroughly with a suitable mixer until a slump-free mortar is obtained, wait for 3 - 5 minutes and again remix it for 15 - 30 sec. The mixed mortar is ready for use and has a pot life of 1 hour at 271C. A 20kg bag will require approximately 3.5 - 4 litres of water. No further water should be added.

2.

3.

4. Do not use in damp condition and 0temperatures less than 5 C.

Spread the material on the work surface equally in a uniform and leveled manner.

Buildup thickness waiting time is 24 hours

Water curing is recommended after 12 hours and to be continued for at least 7 days.

TECHNICAL SPECIFICATION

Mixing ratio Water : Plaster1 : 6

Working time 60 minutes

Mixed density 2.0 - 2.10 g/cc

Application Vertical 5 - 16mm

Compressive StrengthAfter 28 days > 15.0 N/mm

Pack size Coverage

NOTE :

PRECAUTIONSKeep out of reach of children, wear suitable protective clothing. gloves and eyes/face protection. After contact with skin, wash immediately with plenty of clean water. In case of contact with eyes rinse immediately with plenty of clean water and seek medical advice.

CONDITIONS OF SALESold subject to the Company's conditions of sale which are available on request.

NOTE

A 801

thickness

Horizontal 5 - 16mm

0 m

A 801 12

@ 27 1C

VOC content 2.62 g/L

COVERAGE ESTIMATES

2 kg & 50kg Approx. 0.85 /20 kg bag @ 10mm thickness

These figures are theoretical, due to the wastages and the variety / nature of substrates practical coverage figures may be reduced.

STORAGE AND SHELF LIFEhas a shelf life of months when

stored in normal dry conditions.

The information supplied in this datasheet is based upon extensive experience and is given in good faith in order to help you. Our Company policy is one of continuous Research and Development; we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however as we have no control over site conditions or the execution of the work, we accept no liability for any loss or damage which may arise as a result thereof.

DISPOSAL/SPILLAGESpillage of any of the component products should be absorbed onto sand or other inert materials and transferred to a suitable disposable vessel. Disposal of such spillage or empty packaging should be in accordance with local waste disposal authority regulations.

For further information please refer to the Material Safety Data Sheet.

4/14

A 801Ready Mix Plaster

Page 1Page 2