A-6 Electronic Equipment
of 4
Transcript of A-6 Electronic Equipment
-
7/29/2019 A-6 Electronic Equipment
1/4
1/4
A-6E interior S.A.
49 592
49 5921/48 scale detail set for kit sada detail pro modelKinetic 1/48 Kinetic
ORIGINAL KIT PARTSPVODN DLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTAN DLY
PARTS TO BE REMOVEDDLY K ODSTRANN
FILLTMELIT
eduard
REMOVE
ODSTRANIT
OPTION
VOLBA?REPLACENAHRADIT
BENDOHNOUT
GRIND
OBROUSIT
SYMETRICAL ASSEMBLYSYMETRICK MONT
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUT EXPRESS MASK NABARVIT PRED SLEPENM
=
H36
67
68
37
=
H11
H129
80
90
47
1
2
41
40
39
5238
4651
H44H2
64
65
81
82
=
H28
H29
74
74
28
H5
85
8478
77
=H5
342
6
58
57
79
79
86
86
8
7
28
-
7/29/2019 A-6 Electronic Equipment
2/4
2 pcs.C3
C15
C9, C23, C29,C30, C44, C45
C30
C30
4
1311
10
5
14
15
34
33
2 pcs.
22 22
21
26 27
19,26,53
19, 27, 53
31
32
24
23
23
18
53
19
26 27
29
12
16
17
54
49
25
30
44
48
61
61
62
=
H3
7560
73
56
2 pcs.
2/4 49 592
-
7/29/2019 A-6 Electronic Equipment
3/4
EDUARD M.A. 2012 www.eduard.com Made in Czech Republic
eduardFor further detail sets look for 48 730 A-6 electronic equipment(not included in this set)
H10, H42
43
20
36
45
59
87
H4
83
83
76
88
35
50
I9, I10
89
66
69
63
63
6363
7091
I1, I2
55
A1
A271
72
eduardFor further detail sets look for 48 731 A-6 undercarriage(not included in this set)
eduardFor further detail sets look for 48 728 A-6E exterior(not included in this set)
3/4 49 592
-
7/29/2019 A-6 Electronic Equipment
4/4
2. Do not inadvertently place etched componets on an
unwanted surface. Attempts to remove will result indamage to your part.
2. Nepokldejte samolepc dly na voln plochy. Pokudje omylem pilepte, pi pokusu o odlepen dojde kpokozen dlu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na sti dl, na kterch je naneseno lepidlo.1. Separate the etched components from their frames on theprotective paper. Removal from the paper is done only afterseparation of the parts from the frames.
1.Samolepc dly oddlujte od rmeku na podkladovmpape. Po oddlen je sejmte z krycho papru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepc dly berte za hrany nebo za sti, na kterchnen nanesen lepidlo.
5. Lightly place the component in the desired location andposition. Adjust as required. The component will bepermanently affixed when pressed onto its intendedlocation, its location can be adjusted.
5. Dl lehce polote do pozice, ve kter m bt nalepen.
Upravte pesnou pozici a pimknte. Dl dokonale pilnea po pimknut, ped pimknutm lze dlem opatrnmanipulovat.
PARTS WITH GLUE DLY OPATEN LEPIDLEM
4/4 49 592
