9a
-
Upload
shajakhan-hameed -
Category
Documents
-
view
31 -
download
5
Transcript of 9a
Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820Email: [email protected]
04.06
Bronze ‘Y’ Type Strainers
SECTION9a
Hattersley-Section 9a 25/4/06 10:28 am Page 1
04.062
Contents and Numerical Index
Bronze ‘Y’ Strainers
Contents Page
Figure Number Index 2Introduction 3Bronze ‘Y’ Strainers Data Sheets 4 - 8
In this catalogue we have endeavoured to make the information as accurate aspossible, but we cannot accept any responsibility should it be found that in anyrespect the information is inaccurate or incomplete or becomes so as a result offurther developments.
Numerical Index
Fig No Page
817 4807 / 907 5808 / 908 61807 71807C 8
Hattersley-Section 9a 25/4/06 10:28 am Page 2
04.06
Fig. 807 / 817 / 808
Strainers
Removal of debris from fluid transfersystems is vitally important inprotecting the performance of pipelineequipment. Corrosion deposits, scale,jointing compounds and welding slag aswell as more unusual articles must betrapped and prevented from causingsystem contamination and subsequentproblems.
The ‘Y’ type design offers a reliable,cost effective means of equipmentprotection, minimising downtime andmaintenance costs.
Design of the Hattersley strainer isbacked by years of experience in fluid handling particularly in the field of strainer manufacture and under an approved Quality System to BS EN ISO 9001, a quality product is guaranteed.
ScreeningStraining is by the process of directinterception where the fluid passesthrough the perforation holes in the element the size of which are small enough to prevent passage of the particles.
The Hattersley screening element isconstructed from perforated stainlesssteel sheet in accordance with DEOSpec.036 requirements and isinherently stronger than weak meshtype elements which are susceptible tobreaching when partial blockage causesincreased pressure drop or collapsingunder transient vacuum conditions.
Figure 807 and 817 Features■ Bronze construction■ Threaded end 1/2 to 2in.■ Streamlined flow contours
minimise pressure drop.■ Compact design with short face
to face.■ Perforated stainless steel screen ■ Captive asbestos-free
non-stick gasket.■ Comprehensive flow
characteristics available.
Figure 808 Features■ Bronze construction■ Flanged to BS EN 1092-3 PN25.■ Streamlined flow contours
minimise pressure drop.■ Suitable for HTHW and
saturated steam.■ Captive asbestos-free
non-stick gasket.■ Perforated stainless steel screen ■ Available up to 150mm ■ Bolted cover 65mm and above.■ Comprehensive flow
characteristics available.
3
Fig 807
Fig 808
Fig 817
Hattersley-Section 9a 25/4/06 10:28 am Page 3
04.06
Material Specification
Specification
Component Material BS EN ASTM
Cap Brass 12420 CW617N B124 C37700
Screen Stainless Steel 1449 304S15 AISI 304
Body Bronze 1982 CC491K B62 C83600
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 62 68 79 113 119 136
B mm 40 48 53 64 74 94
C mm 15 18 23 27 31 36
D mm 53 66 75 90 107 130
Weight kg 0.2 0.3 0.5 0.9 1.2 1.8
0 40 80 120 160 200Temperature ˚C
18
16
14
12
10
8
6
4
2
0
Pre
ssur
e ba
r
Satu
rate
d S
team
4
A
B
D
C
Pressure/Temperature RatingPN1616 bar -10º to 100ºC7 bar at 170ºC
Test Pressure24 bar hydraulic
SpecificationBronze body304 stainless steel 40 mesh screenEnd connections threaded to BS EN 10266 (BS21 Taper ISO R7)
Fig. 817
Bronze ‘Y’ Type StrainerPN16
D=withdrawal distance for the screen
Hattersley-Section 9a 25/4/06 10:28 am Page 4
Material Specification
Specification
Component Material BS EN ASTM
Body Bronze 1982 CC491K B62
Screen Stainless Steel 10088-1 X10CrNi18-10 AISI 304
Gasket Asbestos Free (non-stick)
Cap Bronze 1982 CC491K B62
Satura
ted
Stea
m
0 40 80 120 160 200 240 Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
32
36
Dimensions
Nominal Size in 1/2 3/4 1 11/4 11/2 2
A mm 68 80 95 115 130 153
B mm 49 64 89 97 116 159
C mm 65 90 115 135 165 235
k Factor 3.3 4.2 3.6 3.2 3.3 3.5
Weight kg 0.4 0.5 0.9 1.5 1.8 3.3
Screen Data
Nominal Size in 1/2 3/4 1 11/4 11/2 2
Holes Dia mm 0.75 0.75 0.75 0.75 0.75 0.75
Holes/cm2 50 50 50 50 50 50
Free Flow Area/cm2 % 22.6 22.6 22.6 22.6 22.6 22.6
Element Area cm2 24.6 36 68.5 107.1 143.1 255
Free Flow Area cm2 5.5 8.1 15.5 24.2 32.3 57.6
% Nominal Bore 434 284 305 305 283 284
B
A
C
Pressure/Temperature RatingPN32 Series B14 bar at 198ºC32 bar from -10 to 100ºCNote: Fig 907 restricted to 135ºC
Test Pressures (Hydraulic)Shell: 48 bar
SpecificationStandard screen has 0.75mm diameter holes.Screwed cap.Ends threaded to BS EN 10266 (BS21 ISO R7)Figure 907 supplied complete with two Fig 631 test points and plugs.
04.06
Fig. 807 /907
Bronze ‘Y’ StrainerPN32 Series B
5
C=withdrawal distance for strainer element
Hattersley-Section 9a 25/4/06 10:28 am Page 5
04.06
Material Specification
Specification
Component Material BS EN ASTM
Body Bronze 1982 CC491K B62
Screen Stainless Steel 10088-1 X10CrNi18-10 AISI
Gasket Asbestos Free (non-stick)
Cap Bronze 1982 CC491K B62
Dimensions
Nominal Size mm 15 20 25 32 40 50 65 80 100 125 150
A mm 100 110 120 157 165 200 267 318 356 445 489
C mm 49 64 89 97 116 159 200 222 265 337 381
D mm 95 105 115 140 150 165 185 200 235 270 300
E mm 65 90 115 135 165 235 290 325 390 450 560
k Factor 3.3 4.2 3.6 3.2 3.3 3.5 6.0 5.6 7.3 5.1 5.7
Weight kg 1.4 1.8 3.0 4.1 5.8 7.7 16 22 32 67 83
Screen Data
Nominal Size mm 15 20 25 32 40 50 65 80 100 125 150
Holes Dia mm 0.75 0.75 0.75 0.75 0.75 0.75 1.6 1.6 1.6 1.6 1.6
Holes/cm2 50 50 50 50 50 50 17 17 17 17 17
Free Flow Area/cm2 % 22.6 22.6 22.6 22.6 22.6 22.6 34 34 34 34 34
Element Area cm2 24.6 36 68.5 107.1 143.1 255 425 579 849 1277 1680
Free Flow Area cm2 5.5 8.1 15.5 24.2 32.3 57.6 144 196 288 434 570
% Nominal Bore 434 284 305 305 283 284 430 385 360 350 320
0 40 80 120 160 200 240Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
Satu
rate
d St
eam
6
A
D
Pressure/Temperature RatingPN2510.5 bar at 186ºC25 bar from -10 to 100ºCNote: Fig 908 restricted to 135ºC
Test Pressures (Hydraulic)Shell: 37.5 bar
SpecificationStandard screen has 0.75mm diameterholes up to and including 50mm size.Larger sizes have 1.6mm holesScrewed cap up to and including50mm. Larger sizes have bolted coverFlanged to BS EN 1092-3Figure 908 supplied complete with twoFig 631 test points and plugs.
Fig. 808 /908
Bronze ‘Y’ StrainerPN25
C
E=withdrawal distance for strainer element
E
Hattersley-Section 9a 25/4/06 10:28 am Page 6
Material Specification
Specification
Component Material BS EN ASTM
Handle Aluminium
Stem DZR Copper Alloy 12164 CW602N
Stem Seal EPDM
Gland Seals Virgin PTFE
Ball DZR Copper Alloy 12164 CW602N
Hard chrome plated
Seat Rings Virgin PTFE
Body DZR Copper Alloy 12165 CW602N
Screen Stainless Steel AISI 304
Cap Gasket Asbestos Free
Cap DZR Copper Alloy 12165 CW602N
1/2" to 1 1/2" Sizes
2" Size
0 20 40 60 80 100 120140Temperature ˚C
28
24
20
16
12
4
0
Pre
ssur
e ba
r
8
Dimensions
Nominal Size in 1/2 3/4 1
A mm 110 129 151
B mm 31 35 42
C mm 48 60 59
D mm 38 46 50
E mm 47 56 56
Drain Plug BSP 1/4 1/4 1/4
Weight kg 0.54 0.80 1.23
7
A
B
Pressure/Temperature RatingPN25 - 1/2” to 11/2” Sizes25 bar -0ºC to 20ºC7 bar at 120ºC
PN20 - 2” Size20 bar -0ºC to 20ºC6 bar at 120ºC
Test Pressure25 bar pneumatic
SpecificationDZR body Blow-out proof stemHard chrome plated ballVirgin PTFE seatsT - handle operated0.8mm diameter perforated 304stainless steel screenDrain plugBS EN 10266 Taper threaded (ISO R7)WRAS Approved Product
Optional FeaturesLeverExtension stemFig 103 hose outlet blowdown valve
04.06
Fig 1807
Dezincification Resistant Strainer Ball Valve PN25
C
D
E
PED Categorisation
Valve Size 1/2 3/4 1
Group 2 Liquids Cat SEP SEP SEP
Hattersley-Section 9a 25/4/06 10:28 am Page 7
04.06
0 20 40 60 80 100 120 140Temperature ˚C
14
12
10
8
6
2
0
Pre
ssur
e ba
r
4
16
18
8
Pressure/Temperature RatingPN165 bar at 120ºC6 bar at 110ºC10 bar at 65ºC16 bar at 30ºC
Test Pressure25 bar pneumatic
SpecificationDZR body Blow-out proof stemHard chrome plated ballVirgin PTFE seatsT - handle operated0.8mm diameter perforated 304stainless steel screenDrain plugCompression ends to BS EN 1254-2Use with R250 (half hard) copper tubeWRAS Approved Product
Optional FeaturesLeverExtension stemFig 103 hose outlet blowdown valve
Fig 1807C
Dezincification Resistant Strainer Ball Valve PN16
AB
C
D
E
Material Specification
Specification
Component Material BS EN ASTM
Handle Aluminium
Stem DZR Copper Alloy 12164 CW602N
Stem Seal EPDM
Gland Seals Virgin PTFE
Ball DZR Copper Alloy 12164 CW602N
Hard chrome plated
Seat Rings Virgin PTFE
Body DZR Copper Alloy 12165 CW602N
Screen Stainless Steel AISI 304
Cap Gasket Asbestos Free
Cap DZR Copper Alloy 12165 CW602N
Compression Ring Brass
Compression Nut Brass 12165 CW617N B124 C37700
Dimensions
Nominal Size in 15 22 28
A mm 137 159 175
B mm 45 50 53
C mm 48 60 59
D mm 38 46 50
E mm 47 56 56
Drain Plug BSP 1/4 1/4 1/4Weight kg 0.6 0.9 1.3
PED Categorisation
Valve Size 15 22 28
Group 2 Liquids Cat SEP SEP SEP
Hattersley-Section 9a 25/4/06 10:28 am Page 8