916-918 Owner's-Operator's manual 12-23-14 Tiller.pdf916 - 918 Owner’s/Operator’s Manual Revised...
Transcript of 916-918 Owner's-Operator's manual 12-23-14 Tiller.pdf916 - 918 Owner’s/Operator’s Manual Revised...
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 1 of 20
THE
MODEL E916/918 HYDRAULIC REAR TINE TILLER OWNER’S/OPERATOR’S MANUAL
CONGRATULATIONS!
You are now the proud owner of the BARRETO Model 916/918 tiller. Please take a moment of your time to look over the following information. Familiarize yourself with the tiller, its characteristics, and method of operation. Pay particular attention to the safety and operating instructions.
If you have any questions or need any replacement parts in the future, please contact us at your convenience. Our toll-free phone number, fax and email are listed below and parts may be ordered through any of these methods.
THANK YOU for your patronage and confidence in BARRETO equipment.
Barreto Manufacturing, Inc. Innovative Equipment Engineered to Last
66498 Hwy 203, La Grande, OR 97850 (800) 525-7348 (541) 963-7348
FAX (541) 963-6755 E-Mail: [email protected] Web Site: http://www.barretomfg.com
Machine Identification Record
Barreto Customer number ________________________
Machine model number ________________________
Machine serial number ________________________
Engine manufacturer ________________________ Engine model number ________________________
Engine serial number ________________________
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 2 of 20
TABLE OF CONTENTS
TILLER ASSEMBLY INSTRUCTIONS 3 BREAK IN PROCEDURE 3 SERVICE INFORMATION 4 BARRETO WARRANTY 5 HOUR METER 5 HONDA GX270 SCHEMATIC 6 SUBARU EX27 SCHEMATIC 7 HYDRAULIC SCHEMATIC 8 SPECIFICATIONS 9 TROUBLESHOOTING 10 LUBRICATING INSTRUCTIONS 12 OPERATING INSTRUCTIONS 13 SAFETY INSTRUCTIONS 14 SAFETY INSTRUCTIONS OVERVIEW 15 LOCATING UNDERGROUND UTILITIES 17 WORKSITE ASSESSMENT 18 CONTACT WITH UNDERGROUND UTILITIES 19 INDEX _________________________________________________________________ 20
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 3 of 20
ASSEMBLY INSTRUCTIONS
1. Remove the tiller from shipping crate. Please inspect immediately for any damage and notify the shipping company and Barreto Manufacturing, Inc. right away if any is found.
2. Screw the handle bar adjustment crank into the lower handle bar adjuster pin.
3. Fasten the handle bar to the tiller using the 1/2" x 3" bolt supplied.
4. Arrange the hoses down the handle bar tube and fasten to the tube with tie wraps provided.
5. Adjust clutch cable by removing all slack in the lever.
6. Check reservoir according to instructions in service information on the following page.
7. Fill the engine with fuel and oil according to the engine manual.
8. Free wheel hubs: Pull one freewheeling pin slightly, using the split ring. Rotate the pin
until the 1/8" diameter roll pin aligns with the slot in the mounting plate. Allow the pin to slide through the slot. Repeat for the other wheel. Roll the tiller until each pin drops into a hole in the hub. The hubs are now locked.
9. Uncoil the wire for the remote engine on/off switch. Route the wire along the clutch
cable to the engine and secure with the cable ties provided. Splice this wire to the kill switch wire on the engine with the electrical splice provided.
10. When documentation refers to “right side” or “left side”, it is relative to the operator’s
position with both hands on the handlebars.
BREAK IN PROCEDURE
KEEP ALL PERSONNEL CLEAR OF MACHINE
DURING BREAK IN TO PREVENT INJURY!!
Before using tiller, lower the depth bar to raise the tines off the ground. Tape clutch handle in closed position and let the machine run for 30 minutes at half throttle with tines in motion.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 4 of 20
SERVICE INFORMATION 1. Check reservoir level using sight glass on the left side of the tank. If required, add to reservoir tractor
transmission / hydraulic fluid. For machine use in ambient temperatures between +32°F (0°C) and +90°F (32°C) hydraulic fluid ISO 68 is recommended. If the machine is operated at temperatures below +32°F (0°C) then hydraulic fluid ISO 46 is recommended. Recheck oil level after the tiller has been run and oil has been circulated through the wheel and tine motors. Routinely check level thereafter. DO NOT OVERFILL THE TANK.
2. Change the hydraulic oil filter after the first 50 hours of use. Change it after every 200 hours
thereafter. 3. Add 1 quart of hydraulic oil to the reservoir with each oil filter change.
4. Check the tine bolts after each use and tighten as needed. Check all hydraulic fittings for
leaks and tighten if necessary. 5. Tines should be changed as often as needed for the machine to do a satisfactory and efficient
tilling job. Use Loctite stud and bearing adhesive/sealant on tine bolt threads to prevent loosening.
6. The grease zerk on both ends of the tine shaft flange bearing should be greased after every 4
to 8 hours of use. 7. Grease zerks on the wheel hubs should be greased once a week or so, depending upon
freewheel use. IMPORTANT: The engine is normally serviced prior to shipping. However, shipping regulations may prohibit this. Check levels and add oil and fuel as required before starting. Service according to the engine manual before starting. IMPORTANT: If the couplers between the engine and the pump are moved or removed for any reason, it is CRITICAL that they have a 1/8” gap between them when reinstalled. Failure to have this gap will result in rapid wear and failure of your pump! NOTE: It is very important to move the fuel shutoff lever to the closed position after stopping the engine. Failure to do so could cause fuel to leak down into the cylinder and crankcase. Damage resulting from this will void your engine warranty and not be covered. WARNING: Running the tiller without hydraulic oil will cause serious damage to the hydraulic pump. CHECK RESERVOIR LEVEL BEFORE STARTING THE MACHINE.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 5 of 20
BARRETO MANUFACTURING, INC. EQUIPMENT WARRANTY Barreto Manufacturing, Inc. warrants all BARRETO equipment to be free of defects in material and workmanship for a period of one (1) year, dating from delivery to the original user.
This Warranty is in lieu of all other warranties, whether written or implied, and is limited to: 1. Replacement of parts returned to the dealer and/or factory and determined defective upon
inspection. (Replacement for parts to dealers shall be at dealer cost plus shipping charges.)
2. Time for pick-up and/or delivery, transportation or service calls by dealers is excluded. Manufacturer reserves the right to determine reasonable time required for repair.
Warranty does not apply to damage caused by abuse or neglect. Time and materials required for normal maintenance and service are also excluded from warranty coverage.
Engines, engine accessories, batteries and tires are warranted by the original manufacturers and are not covered by the Barreto Equipment Warranty. Wear parts such as tiller tines, sprockets, bearings, trencher chain parts including teeth, stump grinder cutting teeth & holders, etc. are also excluded unless it can be determined that a defect has contributed to premature wear.
HOUR METER The DGI® TACH/HOUR hour meter tracks the hours of machine operation in order for routine maintenance to be performed on a timely basis. Your DGI® hour meter is pre-set at the DGI® factory to go into Flash Alert mode at 25-hour intervals. Although the engine manufacturer does not require changing engine oil this often, due to heavy-duty use and extreme conditions inherent to tiller use, Barreto Manufacturing strongly recommends frequent oil changes. Refer to this manual for equipment service requirements and to the Engine Manual for engine service requirements. While Flash Alert is active, hold the tip of the RESET TOOL (Key Kancel Wand) against the meter as shown. Within several seconds, the display will stop flashing indicating the Service Interval has been reset. If the wand gets lost, a small mechanic’s pick-up magnet will work. RESET TOOL
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 6 of 20
ELECTRICAL SCHEMATIC - HONDA GX270
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 7 of 20
ELECTRICAL SCHEMATIC - SUBARU EX27
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 8 of 20
HYDRAULIC SCHEMATIC
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 9 of 20
SPECIFICATIONS MODEL NUMBER 916/918 DIMENSIONS Weight 460 lbs. (208.65kg) Height 36” (0.91m) Length 66” (1.68m) Width 20.75” (527.05mm) ENGINE Engine Options Honda GX270 Subaru EX27 FUEL Gasoline POWER: hp (kW) at 3600 RPM H-8.5 hp (6.34 kW) POWER: hp (kW) at 4000 RPM S-9 hp (6.6 kW) FUEL CAPACITY H-0.95 U.S. gallons (3.6 liters) S-0.94 U.S. gallons (3.6 liters) ENGINE OIL CAPACITY H-.63 quart (.60 liters) S-.63 quart (.60 liters) HOUR METER Standard HYDRAULIC SYSTEM Reservoir Capacity 7.8 U.S. gallons (29.53 liters) OPERATIONS Ground Drive, Forward 78 feet per minute (23.77 m/min) Ground Drive, Reverse 78 feet per minute (23.77 m/min)
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 10 of 20
916/918 TILLER TROUBLE SHOOTING GUIDE CAUTION: ALWAYS USE EXTREME CARE WHEN TROUBLE SHOOTING OR MAKING ADJUSTMENTS ON THE TILLER. STAY CLEAR OF TINES WHEN ENGINE IS RUNNING. ALWAYS SHUT THE ENGINE OFF BEFORE DISASSEMBLING ANY COMPONENT.
A. ENTIRE HYDRAULIC SYSTEM DOES NOT OPERATE AND THE ENGINE IS NOT UNDER LOAD
1. Broken or improperly adjusted clutch (actuator) cable.
2. Low hydraulic oil in tank.
3. Hydraulic pump-to-engine coupler has slipped.
4. Hydraulic pump worn or tine motor relief valve not functioning properly.
If broken, replace. Remove slack then adjust for 7/16” to 1/2" movement at actuator lever pin. Fill to center of sight glass. Check for wear and replace both coupler halves and rubber spider as needed. Follow the series of tests described below:
Remove the tank end of hose that goes from the pump to the tank. Start the engine and with the tines and wheels in neutral, pump off about four gallons of hydraulic oil into a clean bucket. (The .52 CID pump, @ 1000 PSI & 3000 RPM, should pump at the rate of 6.5 GPM.) Replace the hose and remove the tank lid. Remove the end of the intake hose from the fitting on the tank lid. Submerse the end of the hose in the hydraulic oil in the tank. (A non-collapsible hose extension may be required.) Block the tines with a short 4 X 4 and stand to the side.
With tines selected to forward rotation, activate the actuator valve and check to see where the oil enters the tank. If the pump is good, the oil will enter through the relief valve or the return line from the filter. If the oil returns only through the filter return, the tine-drive motor is bad.
If the oil returns through the relief valve but does not kill the engine, check the out-put pressure of the pump. To do this, "T" a 4000 pound gauge into the line at the tank. DO NOT BLOCK THE LINE OR DEAD-HEAD THE GAUGE INTO THE LINE. With the tines in forward and blocked, activate the hydraulic valve as before. The relief valve is set at 2750 pounds. If the gauge reaches this pressure, the valve is OK. If not, the relief valve is bad and needs to be replaced.
If the pressure reaches 2750 pounds but there is only a small amount of oil returning, the pump is worn and should be replaced.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 11 of 20
TROUBLE SHOOTING GUIDE (continued) B. TINES FAIL TO ROTATE BUT WHEELS DRIVE.
1. Clutch cable stretched so needs adjustment
2. Tine motor worn.
Remove cable slack then adjust for 7/16” to 1/2" movement at actuator lever pin. Rebuild or replace motor. New motors are available from Barreto Manufacturing, Inc.
C. WHEELS FAIL TO TURN BUT TINES ROTATE
1. Wheel axle keys have been sheared or removed.
2. Wheel relief valve bad
Replace keys. Replace relief valve.
D. ENGINE LUGS DOWN OR DIES AND WHEELS AND TINES DO NOT TURN.
1. Rocks or other obstruction blocking tines.
2. Tine shaft bound with wire, vines, or grass.
3. Tilling depth too great for soil conditions.
4. Outboard tine shaft bearings binding.
5. Engine improperly tuned or maintained.
6. Low oil alert causes engine to shut down.
7. Engine losing power due to wear.
Shut OFF engine and remove obstruction. Shut OFF engine and remove debris, especially at the ends. Shut OFF engine and lower depth bar to raise the tines, decreasing tilling depth.
Lubricate or replace bearings as needed.
See engine manual and correct as needed.
This may occur if tilling on hills, (not advised). Level the tiller and check engine oil level. Fill if required. Oil alert should reset. See engine manual. See engine manual.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 12 of 20
TROUBLE SHOOTING GUIDE (continued) E. OIL LEAKS IN HYDRAULIC SYSTEM.
1. Fittings are loose.
2. Worn or broken hoses.
3. Oil around tine motor shaft.
Tighten as required. Replace as necessary. Inspect tine motor for leaking shaft seal. Rebuild or replace motor. New motors are available from Barreto Manufacturing, Inc.
F. EXCESSIVE FOAMING OF HYDRAULIC OIL FROM VENT HOSE.
1. Improper oil used.
2. Pump sucking air.
3. Hydraulic pump is faulty.
Verify that hydraulic oil used has anti- foaming additives. * Inspect and tighten fittings on intake side of pump. Test using procedure in section A4 above.
* Recommended oil is CHEVRON 1000 or equivalent hydraulic oil with anti-foaming and anti-wear additives. Hydraulic oil should have an ISO/AW rating of 68.
LUBRICATION INSTRUCTIONS
• The grease zerk on both ends of the tine shaft flange bearing should be greased after every 4 to 8 hours of use.
• Grease zerks on the wheel hubs should be greased once a week or so, depending upon freewheel use.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 13 of 20
OPERATING INSTRUCTIONS
1. READ SAFETY INSTRUCTIONS BEFORE OPERATING!
2. Be sure engine oil and hydraulic oil are at proper levels before starting the tiller.
3. STUDY AND UNDERSTAND CONTROLS BEFORE BEGINNING OPERATION!
4. NEVER RUN THE MACHINE IN REVERSE WHILE TINES ARE ROTATING! 5. Always move the tine control lever to "OFF" before reversing wheels.
6. The TINE DRIVE lever should be set at "OFF" when moving the tiller from place to
place while not tilling.
7. CLUTCH (ACTUATOR) LEVER: (At left handle grip) Activates the wheel drive and tine rotation controls when squeezed. When released, all motion stops.
8. WHEEL DRIVE LEVER: The wheel speed is variable both in forward and reverse.
Moving the WHEEL DRIVE lever to the right causes the tiller to go forward; moving to the left to back up. The farther the control lever is moved away from center, the faster the tiller will travel. When the lever is centered, the wheels are locked in a neutral or park position.
9. TINE DRIVE LEVER: The tines operate at a constant speed. The TINE DRIVE
lever must be moved all the way over to either the forward "ON" position or “REV” position when tilling. If an object becomes lodged in the tines, put the WHEEL DRIVE lever in neutral and change direction of the tines to dislodge it.
10. OPERATE TILLER ON LEVEL GROUND ONLY!
11. TILLING OPERATION: In most soil and sod conditions, the depth bar can be set
with the pin in the third hole from the top. When starting to till, move the TINE DRIVE lever to the ON (forward) or REV position. Tines will dig in either the forward or reverse rotating direction. Squeeze the CLUTCH LEVER completely to engage the tines. Move the WHEEL DRIVE lever to the right until the desired wheel speed is reached. Under most conditions, at least two passes must be made. For deeper tillage, move the depth bar up one hole at a time.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 14 of 20
SAFETY INSTRUCTIONS
1. READ SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING!
2. DO NOT LEAVE TILLER UNATTENDED WITH ENGINE RUNNING.
3. Always park on level surface, never on an incline.
4. USE EXTREME CAUTION IF TRANSPORTING TILLER DOWN ANY INCLINE, ESPECIALLY IF USING RAMPS OFF A PICK-UP TRUCK.
5. The SAFETY CLUTCH (ACTUATOR) lever on the left handlebar is for operator
protection. DO NOT TAPE DOWN OR OTHERWISE BY-PASS THIS SAFETY FEATURE!
6. Objects may become airborne while operating tiller. Wear safety goggles, hard hat,
protective footwear and hearing protection while operating or observing!
7. Rotating tines can cause serious injury. KEEP HANDS AND FEET CLEAR!
8. KEEP TINE COVER CLOSED and MACHINE LEVEL while tines are operating.
9. Buried cables or gas lines can cause serious injury or death. Contact local agencies for location.
10. Fuel exhaust and fuel fumes can cause illness or death. Operate outdoors and avoid
breathing exhaust and fumes.
11. Fuel-fumes can catch fire or explode. Do not smoke or operate near flames or sparks.
12. Hydraulic oil is under extreme pressure and can get under skin and burn or poison. Check for leaks with cardboard.
13. Muffler and engine get hot enough to cause serious burns. Do not touch until cool.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 15 of 20
SAFETY INSTRUCTIONS OVERVIEW READ SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING! USE COMMON SENSE AND PLENTY OF IT! The CLUTCH LEVER on the left handlebar is for the operator’s protection. All motion stops when the lever is released. DO NOT TAPE THE CLUTCH LEVER UP or otherwise by-pass this safety feature! Call before you dig. If you do not call, you may cause an accident; suffer injuries or death; cause interruption of services; damage the environment; and/or incur project delays. Expect to be held liable for any damages caused, if you fail to call.
DANGER: Buried electric cables or gas lines can cause serious injury or death if struck with tines. Always determine location of utilities before tilling.
WARNING: Fiber optic cables convey laser light that can injure your eyesight.
STAY CLEAR of moving parts on the tiller. Wear safety goggles and a hard hat while operating or observing!
WARNING: The tines may throw stones and debris.
Wearing adequate hearing protection while operating or observing is recommended.
WARNING: Exposure to loud noise is cumulative and may permanently damage your hearing.
Wear safety boots and gloves. Wear close-fitting clothing. Contain long hair. Do not wear jewelry. Wear reflective clothing if working near traffic.
Machinery Directive Declaration DECLARED DUAL-NUMBER NOISE EMISSION VALUES
in accordance with ISO 4871 Normal Operation Measured A-weighted sound power level, LWA (ref. 1pW) in decibels 106 Uncertainty, KWA, in decibels 3 Measured A-weighted sound pressure level, LpA (ref. 20µPa) at the operator's position in decibels 87 Uncertainty, KpA, in decibels 4 Values determined according to noise test code given in Directive 2000/14/EC Annex III B54 (Trencher) / BS EN ISO 4254-1 Annex B (Tiller) using the basic standard ISO 3744: 1994 NOTE 1 - The sum of a measured noise emission value and its associated uncertainty represents an upper boundary of the range of values which is likely to occur in measurements. Values listed above are rounded to the nearest decibel according to ISO 4871
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 16 of 20
SAFETY INSTRUCTIONS OVERVIEW (continued) Only operate outdoors and avoid breathing engine exhaust and fumes.
WARNING: Engine exhaust contains carbon monoxide gas that is toxic. Breathing it can cause unconsciousness and death.
Adequate lighting is required, daylight or artificial, for safe operation of the tiller. Allow adequate side and overhead clearances between tiller and buildings, fences, and trees.
WARNING: Contact with the tines while in operation will cause serious injury or even death.
Keep away from tires to avoid getting crushed.
WARNING: Getting run over by the tiller will cause injury.
Always leave tiller parked on a level surface.
WARNING: Do not park on incline. Move the tiller to a level surface. Do not leave tiller unattended with the engine running.
Avoid inclines if at all possible.
WARNING: Navigating on any incline increases the danger of the tiller losing traction or rolling over, especially if the surface is wet. If you lose control get out of the way immediately to avoid personal injury. Navigation on inclines should be especially slow and turns very gradual.
A 20° maximum incline is allowed. Honda engines have an Oil Alert system that will automatically stop the engine if tipped more than 20°.
Do not operate tiller near any source of flammable dust or vapors.
WARNING: Sparks from the engine exhaust can cause an explosion or fire in a flammable or explosive atmosphere. Fuel fumes can catch fire or explode.
Do not operate tiller near flames or sparks.
WARNING: Fuel fumes can catch fire or explode.
Shut off engine and allow it to cool before refueling.
WARNING: Fuel fumes can catch fire or explode. Do not smoke when refueling. Do not refuel near a source of flames or sparks.
Do not touch the engine, muffler, or any of the hydraulic components until cool.
WARNING: Muffler and engine get hot enough to cause serious burns. For the safety of yourself and others, allow enough time for the engine, muffler, and the hydraulic fluid to cool
completely before performing any cleaning or maintenance.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 17 of 20
SAFETY INSTRUCTIONS OVERVIEW (continued)
Avoid contact with hydraulic fluid. WARNING: When machine is operating, hydraulic fluid is under extreme pressure and can get under skin and burn or poison.
Keep others away. If the job site is near a road or pedestrian path, warn and divert both motorized traffic and pedestrians. As appropriate, use traffic flag personnel, signs, cones, and lighting devices to insure safety.
Never allow anybody to ride on the tiller. Never lift the tiller over any person at any time.
WARNING: If tiller should fall it would crush anybody under it.
We recommend having a fire extinguisher suitable for petrol fires in the operating area.
Attachments can change the center of mass and machine operations. Use only Barreto attachments. DETERMINE LOCATION OF UNDERGROUND UTILITIES
OSHA CFR 29 1926.651 requires that the estimated location of underground utilities be determined before beginning excavation or an underground drilling operation. When the actual excavation or bore approaches an estimated utility location, the exact location of the underground installation must be determined by a safe, acceptable and dependable method. If any utility cannot be precisely located, the appropriate utility company must shut it off.
Call before you dig. If you do not call, you may cause an accident; suffer injuries or death; cause interruption of services; damage the environment; and/or incur project delays. Expect to be held liable for any damages caused, if you fail to call.
DANGER: Buried electric cables or gas lines can cause serious injury or death if struck with tiller tines. Always determine location of utilities before tilling.
WARNING: Fiber optic cables convey laser light that can injure your eyesight.
CALL 1-888-258-0808 TO LOCATE UTILITIES BEFORE TILLING (US. OR CANADA). This free service will provide a “One-Call” number for the geographic area that you select. Before you start any digging project, be sure to call the local One-Call system in your area and any utility company that does not subscribe to the One-Call system. The One-Call representative will notify participating utility companies of your proposed digging activities. Utilities will then mark their underground facilities by using the following international marking codes:
Red Electric Yellow Gas, oil, or petroleum Orange Communication, telephone, television Blue Potable water Green/brown Sewer White Proposed excavation Pink Surveying
For areas not represented by One-Call Systems International, contact the appropriate utility companies to locate and mark the underground installations. Do not rely on visual evidence of underground utilities such as manhole covers or electrical drop boxes…CALL!
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 18 of 20
WORK SITE ASSESSMENT
Examine the work area for any conditions or obstructions that may inhibit tilling or create a safety hazard for the operator or others. Use the information in this manual combined with good judgment to identify any hazards to avoid. In addition to calling to DETERMINE LOCATION OF UNDERGROUND UTILITIES (see previous section for details), the operator and/or job foreman should visually inspect the work site. Look for electrical drop boxes, notices of underground placements, manhole covers, recent trenching or tilling activity, any evidence of possible underground placements, banks, drop-offs, rocks, wire, uneven terrain, any existing holes and toxic ground conditions.
Only operate tiller outdoors and avoid breathing engine exhaust and fumes. WARNING: Engine exhaust contains carbon monoxide gas that is toxic. Breathing it can cause unconsciousness and death.
Do not operate tiller near any source of flammable dust or vapors. WARNING: Sparks from the engine exhaust can cause an explosion or fire in a flammable or explosive atmosphere. Fuel fumes can catch fire or explode.
Allow adequate side and overhead clearances between tiller and any objects such as buildings, fences, and trees.
Adequate lighting is required, daylight or artificial, for safe operation of the tiller.
Keep others away. If the job site is near a road or pedestrian path, warn and divert both motorized traffic and pedestrians. As appropriate, erect barriers, use traffic flag personnel, signs, cones, and lighting devices to insure safety. WARNING: Someone could step into the tilled area by accident. Walking near the edge of the tilled area could cause loss of balance and possibly cause someone to fall into the rotating tines. Contact with the rotating tines while in operation will cause serious injury or even death.
MACHINE FUNCTION CHECK: If the operator releases the CLUTCH LEVER, the wheel drive and rotating tines should stop. This is intended for your safety and must be maintained in good functional condition. Contact your dealer or the factory if anything on the tiller does not function properly.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 19 of 20
CONTACT WITH UNDERGROUND UTILITIES After LOCATING UNDERGROUND UTILITIES and performing the WORK SITE ASSESSMENT, accidental tine contact with a buried utility might still occur. If it does, stop tilling and call 911 for help. If you cut a wire or cable, assume that you do not know what kind it is. It may be electrical or any one of several communication lines: telephone, television, or fiber optic. In any case, do not touch it or even look at the ends of it. Stop tilling and call 911 for help. Do not till any more until the appropriate utility company has assessed the situation, taken appropriate action, and informed you that is safe to proceed. If you strike a pipe, it could be gas, oil, petroleum, water or sewer. In any case, stop tilling, shut off the engine, and evacuate the area immediately. Call 911 for help. Electrical wires or cables: If you think that you may have severed electrical wires, stop tilling and call 911 for help. Keep yourself and other people away from the area.
DANGER: An electric shock could kill you. Assume that any severed wire or cable is HOT with voltage and do not touch it!
Gas lines: If you think that you may have struck a gas line, shut off the engine and evacuate the area immediately. Call 911 for help.
DANGER: A gas explosion could kill you. Sparks will likely occur from the tines scraping the metal pipe. If gas leaks out an explosion could easily occur.
Fiber optic cables: If you think that you may have severed a fiber optic cable, do not touch or even look at the ends of it.
WARNING: Fiber optic cables convey laser light that can injure your eyesight. Call 911 for help.
916 - 918 Owner’s/Operator’s Manual Revised 12/23/14
Page 20 of 20
INDEX
ACTUATOR, 10, 11
ASSEMBLY INSTRUCTIONS, 3
BREAK IN PROCEDURE, 3
CALL BEFORE YOU DIG, 15, 17
CLUTCH LEVER, 18
CLUTCH LEVER, 13, 15
ELECTRICAL SCHEMATIC - HONDA GX270, 6
ELECTRICAL SCHEMATIC - SUBARU EX27, 7
ENGINE, 3, 4, 5, 9, 10, 11, 13, 14, 16, 18, 19
EXHAUST, 14, 16, 18
FREE WHEEL HUBS, 3
FUMES, 14, 16, 18
GREASE, 4, 12
HARD HAT, 14, 15
HEARING PROTECTION, 14, 15
HOUR METER, 5
HYDRAULIC, 10, 12, 14
HYDRAULIC FLUID, 4, 10, 12, 13, 16, 17
HYDRAULIC OIL FILTER, 4
HYDRAULIC PUMP, 4
HYDRAULIC SCHEMATIC, 2, 8
INCLINES, 16
LUBRICATION. See GREASE
NOISE EMISSION VALUES, 15
OPERATING INSTRUCTIONS, 2, 13, 14, 15
REFUELING, 16
SAFETY BOOTS, 15
SAFETY GOGGLES, 14, 15
SAFETY INSTRUCTIONS, 2, 13, 14, 15, 16, 17
SERVICE INFORMATION, 4
SPECIFICATIONS, 9
TINE DRIVE LEVER, 13
TINE SHAFT, 4, 11, 12
TINES, 3, 4, 10, 11, 13, 14, 15, 16, 17, 19
TROUBLE SHOOTING, 10, 11, 12
UNDERGROUND UTILITIES, 17, 18, 19
WARRANTY, 2, 5
WHEEL DRIVE, 13, 18
WORK SITE, 18, 19
THE
MODEL E916/918 HYDRAULIC REAR TINE TILLER
EXPLODED VIEWS WITH PART NUMBERS
CONGRATULATIONS! You are now the proud owner of a BARRETO tiller. The following pages have detailed views of your tiller, along with corresponding part numbers. If you have any questions or need any replacement parts in the future, please contact us at your convenience. Our toll-free phone number, fax and email are listed below and parts may be ordered through any of these methods. Thank you for your patronage and confidence in BARRETO equipment. Barreto Manufacturing, Inc. Innovative Equipment Engineered to Last 66498 Highway 203 La Grande, OR 97850 1-800-525-7348 1-541-963-6755 Fax E-Mail: [email protected] Web Site: http://www.barretomfg.com Machine Identification Record BARRETO Customer number Machine model number Machine serial number Engine manufacturer Engine model number Engine serial number
34
19
17
9
68
13
12
54
3
7
22
26
28
2930
23
3231
2733
1415
1618
12
24
25
11
5
5
6
2
8
6
21
6
.030
TH
RU
ST W
ASH
ER H
ERE
3
20
10
RE
F.Q
TY.P
ART
NO
.D
ES
CR
IPTI
ON
11
1084
0LE
FT H
AN
D S
IDE
PLA
TE, T
RA
NS
MIS
SIO
N2
505
149
WA
SH
ER
, 7/1
6 S
AE
ZIN
C3
605
060-
01H
H C
AP
SC
RE
W, 7
/16-
20 N
F X
3/4
G5
ZIN
C4
310
034
SH
AFT
, TR
AN
SM
ISS
ION
GE
AR
S5
310
031
SP
AC
ER
, SH
OR
T6
603
274
THR
US
T W
AS
HE
R, .
891
X 1
.502
X .0
35, H
AR
D7
110
058
GE
AR
, WH
EE
L D
RIV
E, 1
6T, 1
/2 F
AC
E8
210
453
BU
SH
ING
, CA
ST
BR
ON
ZE, 7
/8 X
1 X
1-5
/16
92
1003
3S
PA
CE
R, L
ON
G10
110
061
GE
AR
, WH
EE
L D
RIV
E, 3
6T/1
5T, 1
/2 F
AC
E11
110
059
GE
AR
, WH
EE
L D
RIV
E, 1
5T X
1-5
/16
OL
121
1003
2S
PA
CE
R, M
ED
IUM
131
1006
2G
EA
R, W
HE
EL
DR
IVE
, 36T
/15T
, 3/4
FA
CE
141
1006
0G
EA
R, W
HE
EL
DR
IVE
, 15T
X 2
-1/4
OL
151
1045
4B
US
HIN
G, C
AS
T B
RO
NZE
, 7/8
X 1
X 2
-1/4
162
0555
0R
OLL
PIN
(SLO
TTE
D S
PR
ING
), 1/
4 X
5/8
ZIN
C17
202
121
PIN
, TR
AN
SM
ISS
ION
181
1083
9R
IGH
T H
AN
D S
IDE
PLA
TE, T
RA
NS
MIS
SIO
N19
210
037
WA
SH
ER
, 1/2
X 1
-3/4
X 1
/420
205
067
HH
CA
P S
CR
EW
, 1/2
-13
NC
X 1
G5
ZIN
C21
203
002
O-R
ING
, 2-2
10, 1
" OD
X 1
/8 S
EC
TIO
N22
102
122
MO
UN
TIN
G B
LOC
K, W
HE
EL
DR
IVE
MO
TOR
231
0533
1S
H C
AP
SC
RE
W, 1
/4-2
0 N
C X
3/4
G5
PLA
IN24
105
096
NU
T, N
YLO
CK
, 1/4
-20
NC
ZIN
C
RE
F.Q
TY.P
ART
NO
.D
ES
CR
IPTI
ON
254
0505
9H
H C
AP
SC
RE
W, 3
/8-1
6 N
C X
1 G
5 ZI
NC
261
0391
5O
-RIN
G, 2
-438
N70
, 6-3
/4 O
D X
1/4
SE
CTI
ON
271
0470
1W
HE
EL
DR
IVE
MO
TOR
WIT
H K
EY
281
0207
5G
EA
R, W
HE
EL
DR
IVE
MO
TOR
291
0554
2W
AS
HE
R, 1
/4 F
EN
DE
R P
LAIN
301
0506
9W
HIZ
LO
CK
, 1/4
X 5
/831
204
557
FITT
ING
, 680
2-8-
1032
103
001
O-R
ING
, 2-1
52, 3
-7/1
6 O
D X
3/3
2 S
EC
TIO
N33
205
587
SH
CA
P S
CR
EW
, 1/2
-13
NC
X 1
-3/4
G5
ZIN
C34
103
198
THR
US
T W
AS
HE
R, .
481
X .9
35 X
.030
TRA
NSM
ISSI
ON
DW
G#
0023
7 R
1SC
ALE
: 1:4
.3PR
OD
UC
T LI
NE:
916
TIL
LER
SHEE
T 1
OF
1
TITL
E:
DA
TE: 4
/27/
07
1
35
38
3331302928
27
26
32
12
13
12
20 21 22 23
3
14
12
1
813
4
10
8
9
16
13
1137
36
17 17 18
15
19
3940
2
6
3425
2
24
5
FOR
916
R, U
SE
PA
RT
NO
. 106
34 (I
GN
ITIO
N W
IRE
, 916
R)
1
2
FOR
916
R, E
NG
INE
IS P
AR
T N
O. 0
7009
(9H
P R
OB
IN W
/O C
YC
LON
E)
7
RE
F.Q
TY.
PA
RT
NO
.D
ES
CR
IPT
ION
11
1070
191
6 &
918
BO
DY
, BO
LT O
N T
OR
QU
E T
UB
E2
203
520
MA
GN
ET
31
1036
1F
ITT
ING
, 640
9-8
PLU
G4
110
188
EN
GIN
E G
UA
RD
, 916
51
0380
6Q
UIC
K-S
PLI
CE
61
0700
6E
NG
INE
, 9 H
P H
ON
DA
GX
270
72
1118
8S
PA
CE
R, 9
HP
EN
GIN
ES
88
0510
1W
AS
HE
R, 3
/8 S
AE
ZIN
C9
205
092
HH
CA
P S
CR
EW
, 3/8
-16
NC
X 1
-1/2
G5
ZIN
C10
205
284
HH
CA
P S
CR
EW
, 3/8
-16
NC
X 2
-1/2
G8
ZIN
C11
205
073
NU
T, N
YLO
CK
, 3/8
-16
NC
128
0505
6H
H C
AP
SC
RE
W, 3
/8-2
4 N
F X
1 G
5 Z
INC
138
0507
2N
UT
, NY
LOC
K, 3
/8-2
4 N
F14
110
035
MO
UN
TIN
G P
LAT
E, H
AN
DLE
BA
R15
410
064
BU
SH
ING
, NY
LAT
RO
N, 1
" O
D S
OLI
D16
103
501
BU
SH
ING
, IG
US
MF
I-08
10-0
817
410
469
TH
RU
ST
WA
SH
ER
, .50
0 X
1.0
00 X
.125
NY
LAT
RO
N18
305
102
WA
SH
ER
, 1/2
SA
E Z
INC
HA
RD
EN
ED
193
0509
8N
UT
, NY
LOC
K, 1
/2-1
3 N
C20
110
068
PIN
, HA
ND
LE B
AR
211
0306
5H
AIR
SP
RIN
G C
OT
TE
R #
422
103
080
SP
RIN
G23
110
036
HA
ND
LE B
AR
BR
AC
KE
T24
110
558
IGN
ITIO
N W
IRE
, 916
256
0303
5T
IE W
RA
P, 1
/8 X
626
105
273
NU
T, N
YLO
CK
, 5/1
6-18
NC
271
0506
8W
AS
HE
R, 5
/16
SA
E Z
INC
281
1055
5W
ED
GE
291
0390
7O
-RIN
G, 2
-111
, 5/8
OD
X 3
/32
SE
CT
ION
301
0252
6H
OU
SIN
G, 2
-111
O-R
ING
& F
LAN
GE
SC
RE
W31
105
138
HH
FLA
NG
E S
CR
EW
, 5/1
6-18
NC
X 1
-1/4
G8
ZIN
C32
110
056
AC
CE
SS
PLA
TE
3310
0506
9W
HIZ
LO
CK
, 1/4
-20
UN
C X
5/8
341
1052
6F
ITT
ING
, 640
9-12
PLU
G35
110
189
R2
BR
EA
TH
ER
HO
SE
AS
SE
MB
LY36
103
040-
06D
EC
AL,
"H
YD
RA
ULI
C O
IL O
NLY
"37
103
040-
16D
EC
AL,
"C
E"
381
0304
0-11
DE
CA
L, "
BA
RR
ET
O",
2-3
/16
X 7
-3/8
391
0304
0-57
DE
CA
L, "
HY
DR
AU
LIC
OIL
LE
VE
L"40
103
503
SIG
HT
GA
UG
E
TITL
E:
SH
EE
T 1
OF
1
BO
LT O
N T
OR
QU
E T
UB
E
DW
G#
PR
OD
UC
T LI
NE
: 916
/18
DA
TE: 1
2/4/
06S
CA
LE: 1
:7.2
BO
DY
,
0023
8 R
4
24
22
21
15
1413
12
198
20
12
18
1617
7
21
34
54
6
11
109
2325
RE
FQ
TY.P
ART
NO
.D
ES
CR
IPTI
ON
11
0401
6A
CTU
ATO
R V
ALV
E, O
-RIN
G P
OR
TS2
105
028
C-C
LIP
, 3/4
"3
103
055
SP
RIN
G, V
ALV
E S
PO
OL
RE
TUR
N4
203
056
CO
LLA
R, 3
/8 ID
51
0510
8W
AS
HE
R, 3
/8 U
SS
, ZIN
C6
105
092
HH
CA
P S
CR
EW
, 3/8
-16
NC
X 1
-1/2
G5
ZIN
C7
104
567
FITT
ING
, 640
7-8-
88
110
391
AC
TUA
TOR
HO
US
ING
PLA
TE9
103
077
O-R
ING
, 3-9
08N
90, -
8 FI
TTIN
GS
101
0400
8-D
OR
ELIE
F V
ALV
E, 2
750
PO
UN
D, O
-RIN
G11
110
481
RE
TUR
N T
UB
E, #
8 0-
RIN
G12
203
060
BU
SH
ING
, IG
US
MFI
-101
2-06
131
0302
0S
EA
L14
103
061
FELT
WA
SH
ER
, 5/8
X 1
X 1
/815
110
053
AC
TUA
TOR
AR
M16
101
054
AC
TUA
TOR
PLA
TE17
105
125
HH
CA
P S
CR
EW
1/4
-20
NC
X 1
-1/4
G5
ZIN
C18
105
096
NU
T, N
YLO
CK
, 1/4
-20
NC
ZIN
C19
605
069
WH
IZ L
OC
K, 1
/4-2
0 N
C X
5/8
ZIN
C20
104
017
FITT
ING
, 680
3-8-
8-8
211
0508
1W
AS
HE
R, 1
/4 S
AE
ZIN
C22
105
039
CIR
CLE
CO
TTE
R C
C-3
231
1288
0V
ALV
E L
OC
ATO
R24
105
294
HH
CA
P S
CR
EW
, 5/1
6-18
NC
X 1
-1/2
G5
ZIN
C25
105
541
WA
SH
ER
, 5/1
6 FE
ND
ER
ZIN
C
AC
TUA
TOR
VA
LVE
DW
G#
TITL
E:
SCA
LE: 1
:2.5
PRO
DU
CT
LIN
E: 9
16 T
ILLE
R
D
ATE
: 10/
13/1
4
SHEE
T 1
OF
100
239
R3
SH
EE
T 1
OF
1
FOR
1-1
/8 F
RE
E W
HE
EL
HU
BS
DW
G#
PR
OD
UC
T LI
NE
: 916
TIL
LER
DA
TE: 1
1/11
/08
SC
ALE
: 1:3
.2
TITL
E:A
XLE
,
0024
0 R
3
1
1A
LL W
AS
HE
RS
MA
Y N
OT
BE
RE
QU
IRE
D T
O F
ILL
EN
D P
LAY
.
21
4
18
14
19
9
1
10
12
22
74
16
13
5
8
11
23
2
17
415
7
3
6
6
12
3
20
4
RE
FQ
TY.
PA
RT
NO
.D
ES
CR
IPT
ION
11
1023
3A
XLE
, WH
EE
L2
205
199
KE
Y, 1
/4 X
1/4
X 2
-1/2
HA
RD
EN
ED
32
0504
4G
RE
AS
E Z
ER
K, 1
/4-2
8 U
NF
48
0320
2T
HR
US
T W
AS
HE
R, 1
.25
X 1
.75
X .0
305
110
289
AX
LE T
UB
E, 1
-5/8
LO
NG
, FO
R P
IN6
210
290
RO
LL P
IN (
SLO
TT
ED
SP
RIN
G),
3/1
6 X
1-1
/8 Z
INC
72
0308
5B
US
HIN
G, C
AS
T B
RO
NZ
E, 1
-1/4
X 1
-3/8
X 1
-1/4
81
1004
1S
PA
CE
R9
110
063
GE
AR
, WH
EE
L D
RIV
E,
36T
X 1
-1/4
101
0501
5K
EY
, 5/1
6 X
5/1
6 X
1-1
/411
110
841
AX
LE T
UB
E, 1
-1/4
LO
NG
, FO
R P
IN12
205
033
HA
IR S
PR
ING
CO
TT
ER
P2
132
0229
7H
OU
SIN
G, A
XLE
BE
AR
ING
142
0328
0B
ALL
BE
AR
ING
, SK
F 6
206
152
0318
9O
-RIN
G, 2
-230
, 2-3
/4 O
D X
1/8
SE
CT
ION
162
0392
4O
-RIN
G, 2
-145
, 2-3
/4 O
D X
3/3
2 S
EC
TIO
N17
805
315
HH
CA
P S
CR
EW
, 5/1
6-18
NC
X 1
G5
ZIN
C18
202
298
HO
US
ING
, AX
LE S
EA
LS19
805
068
WA
SH
ER
, 5/1
6 S
AE
ZIN
C20
205
114
SE
AL,
AX
LE21
210
148
TH
RU
ST
WA
SH
ER
, 1.2
00 X
1.6
43 X
.040
ZIN
C22
210
147
SN
AP
RIN
G, H
O-1
65, 4
2mm
INT
ER
NA
L Z
INC
234
0560
6S
NA
P R
ING
, 1-1
/8"
EX
TE
RN
AL
7
13
2625
2422
1
10
USE
271
LO
CTI
TE
NO
TES:
CO
MES
WIT
H S
ET S
CR
EW.
REP
LAC
EMEN
TSE
T SC
REW
IS 5
/16
X 5
/16,
PA
RT
NO
. 051
27.
29
2625
30
2
19 1612
23
1
31
20
27
32
28
USE
271
LO
CTI
TE.
SHA
FT (N
OT
SHO
WN
).
21
3 4 5
3435
36
33
6
8
15 2
14
37
18 179
11
SCR
EW IN
TO E
NG
INE
1
US
E 2
71 L
OC
TITE38
RE
FQ
TY.P
ART
NO
.D
ES
CR
IPTI
ON
11
0400
4-A
PU
MP
, HY
DR
AU
LIC
22
0453
0FI
TTIN
G, 4
601-
16-1
23
104
219
FITT
ING
, 460
4-12
-12
42
0500
8C
LAM
P, 1
" HO
SE
, CTB
-29
51
1079
6H
OS
E, R
ETU
RN
TO
TA
NK
61
0395
1FI
LTE
R, H
YD
RA
ULI
C O
IL, W
ITH
BY
-PA
SS
71
1085
3FI
TTIN
G, 3
/4 H
OS
E B
IB, 1
/2 N
PT
84
0561
1S
H C
AP
SC
RE
W, 1
/4-2
0 N
C X
3/4
ZIN
C9
103
075
O-R
ING
, 3-9
12N
90, -
12 F
ITTI
NG
S10
110
851
MO
UN
TIN
G P
LATE
, HO
SE
BIB
FIT
TIN
GS
111
0102
0P
IPE
NIP
PLE
, 1/2
X 6
, SC
H 4
012
110
860
SU
CTI
ON
TU
BE
, #20
O-R
ING
131
0329
3O
-RIN
G, 3
-920
N90
, -20
FIT
TIN
GS
141
1024
7S
UM
P S
CR
EE
N #
20 E
XT
#12
INT
O-R
ING
154
0522
5C
LAM
P, 1
-1/2
" HO
SE
, CTB
-36
ST
161
1018
4H
OS
E, S
UM
P S
CR
EE
N17
110
855
O-R
ING
, 3-9
14N
90, -
14 F
ITTI
NG
S18
110
852
FITT
ING
, 1" H
OS
E B
IBS
191
1085
4H
OS
E, P
UM
P IN
TAK
E20
205
101
WA
SH
ER
, 3/8
SA
E Z
INC
212
0509
1H
H C
AP
SC
RE
W, 3
/8-1
6 N
C X
1-1
/4 G
5 ZI
NC
221
0455
4FI
TTIN
G, 6
801-
8-8
231
0420
9FI
TTIN
G, 6
410-
10-8
241
1074
7JA
W C
OU
PLE
R, P
UM
P. 5
/8 B
OR
E25
203
022
SP
IDE
R, R
UB
BE
R26
210
738
PIL
OT
271
1073
7C
OU
PLE
R S
HA
FT, P
UM
P S
IDE
281
0507
7N
UT,
NY
LOC
K, 7
/16-
20 N
F ZI
NC
291
1073
9C
OU
PLE
R S
HA
FT, E
NG
INE
SID
E30
103
023
JAW
CO
UP
LER
, 1" B
OR
E L
095
311
0501
4K
EY
, 1/4
X 1
/4 X
3/4
321
1018
0S
PA
CE
R, E
NG
INE
SH
AFT
332
0509
6N
UT,
NY
LOC
K, 1
/4-2
0 N
C Z
INC
344
0506
9W
HIZ
LO
CK
, 1/4
-20
NC
X 5
/8 Z
INC
351
1079
8B
RA
CK
ET,
FIL
TER
HE
AD
361
0440
3FI
LTE
R H
EA
D, #
12 O
-RIN
G37
110
808
FITT
ING
, 640
0-8-
1238
105
143
SE
T S
CR
EW
.25
NF
X .2
5 C
UP
SHEE
T 1
OF
1
TITL
E:
DW
G#
PRO
DU
CT
LIN
E: 9
16
DA
TE: 2
/15/
06SC
ALE
: 1:5
.6
PUM
P
0024
1 R
3
65
4
75
4
32
1
12109310
1098
1413
1617
1111
1 1
IND
ICAT
ED IT
EMS
MAY
BE
OR
DER
ED A
S A
KIT,
PAR
T N
O. 0
1030
-KIT
(KIT
, HAN
DLE
BAR
AD
JUST
MEN
T).
IND
ICAT
ED IT
EMS
MAY
BE
OR
DER
ED A
S A
KIT,
PAR
T N
O. 1
0667
-KIT
(KIT
, HO
SE K
EEPE
R W
/FAS
TEN
ERS)
.
1
2018
22
1921
15
23
2
22
22
2
RE
FQ
TY.P
ART
NO
.D
ES
CR
IPTI
ON
11
0101
7H
AN
DLE
BA
RS
21
0202
7-L
HA
ND
LE B
AR
AD
JUS
TER
PIN
, LO
WE
R3
405
216
SN
AP
RIN
G, 3
/4 E
XTE
RN
AL
42
0350
1B
US
HIN
G, I
GU
S M
FI-0
810-
085
205
102
WA
SH
ER
, 1/2
SA
E Z
INC
HA
RD
EN
ED
61
0509
3H
H C
AP
SC
RE
W, 1
/2-1
3 N
C X
3 G
5 ZI
NC
71
0509
8N
UT,
NY
LOC
K, 1
/2-1
3 N
C Z
INC
81
0103
0C
RA
NK
, HA
ND
LE B
AR
AD
JUS
TME
NT
92
0505
8W
AS
HE
R, 3
/8 N
YLO
N10
305
103
WA
SH
ER
, 3/8
A32
5 H
AR
DE
NE
D Z
INC
111
0202
7-U
PIN
, HA
ND
LE B
AR
AD
JUS
TME
NT,
UP
PE
R12
205
269
NU
T, 3
/8-1
6 N
C G
RB
ZIN
C
RE
FQ
TY.P
ART
NO
.D
ES
CR
IPTI
ON
132
0303
2-01
GR
IP, 1
X 5
(P/N
030
32 IS
A P
AIR
)14
103
029
LEV
ER
AS
SE
MB
LY (C
OM
PLE
TE)
151
1005
7C
AB
LE, A
CTU
ATO
R16
103
341-
07D
EC
AL,
"IG
NIT
ION
OFF
/ON
"17
106
420
RO
CK
ER
SW
ITC
H, I
GN
ITIO
N O
FF/O
N18
210
667
HO
SE
KE
EP
ER
192
1066
8S
PA
CE
R, H
OS
E K
EE
PE
R20
205
065
HH
CAP
SC
REW
, 5/1
6-18
NC
X 2
-3/4
G5
ZIN
C21
405
068
WA
SH
ER
, 5/1
6 S
AE
ZIN
C22
205
273
NU
T, N
YLO
CK
, 5/1
6-18
NC
ZIN
C23
103
009
R1
HO
UR
ME
TER
, WIT
H F
LAS
H A
LER
T
DW
G#
PRO
DU
CT
LIN
E: 9
16
1/
16/0
7SC
ALE:
1:6
.2
TITL
E:
SHEE
T 1
OF
1
HAN
DLE
BAR
S &
CR
ANK
0025
0 R
1
CO
NTR
OL
VA
LVE
DW
G#
TITL
E:
SCA
LE: 1
:3PR
OD
UC
T LI
NE:
916
D
ATE
: 4/2
6/07
SHEE
T 1
OF
100
251
R1
16
15 6 5
4
3
14
10
9
18
6
13
2
7
12
1117
1
8
RE
FQ
TY.P
ART
NO
.D
ES
CR
IPTI
ON
11
0401
0C
ON
TRO
L V
ALV
E B
OD
Y (O
RD
ER
040
10-K
)2
405
200
RO
LL P
IN (S
LOTT
ED
SP
RIN
G),
1/4
X 1
-1/4
ZIN
C3
104
015-
DV
ALV
E S
PO
OL,
TIN
ES
(OR
DE
R 0
4010
-K)
44
0300
2O
-RIN
G, 2
-210
, 1" O
D X
1/8
SE
CTI
ON
54
0302
5B
AC
K-U
P R
ING
, 1" T
EFL
ON
64
0501
0S
NA
P R
ING
, 1" E
XTE
RN
AL
71
0401
5-C
VALV
E SP
OO
L, W
HEE
L D
RIV
E (O
RD
ER 0
4010
-K)
81
0502
3P
IPE
PLU
G, 1
/8"
94
0452
0FI
TTIN
G, 6
400-
8-8
102
0455
4FI
TTIN
G, 6
801-
8-8
114
0330
0FI
TTIN
G, 6
409-
4 P
LUG
121
0304
0D
EC
AL,
CO
NTR
OL
VA
LVE
132
0302
7D
ETE
NT
SP
RIN
G14
202
017
HA
ND
LE, 5
/16
X 7
152
0557
3S
H C
AP
SC
RE
W, 1
/4-2
0 N
C X
3/8
ZIN
C16
203
026
KN
OB
, 5/1
6-N
C17
205
065
HH
CA
P S
CR
EW
, 5/1
6-18
NC
X 2
-3/4
G5
ZIN
C18
205
273
NU
T, N
YLO
CK
, 5/1
6-18
NC
ZIN
C
16"
OR
18"
DIG
GIN
G W
IDTH
DW
G#
PR
OD
UC
T LI
NE
: 916
& 9
18 T
ILLE
R
DA
TE: 4
/26/
07S
CA
LE: 1
:9.2
TITL
E:
SH
EE
T 1
OF
1
TIN
E S
EC
TIO
N, 00
253
R2
320
7
54
10
16
21
4140
39
119
49
48
53
55
50
89
25
13
22
1415
17
28
26
23
11
11
5
1
1918
5
2
4
7
4
1 2 3
RE
FER
EN
CE
DW
G. 1
0144
FO
R IN
DIV
IDU
AL
PA
RTS
.
4
8
42 43
464544
12
12
47
3536
3738
34
33
24
5251
2930
3132
3
1
6
2
5 6 7 8
6
FOR
918
, US
E P
AR
T N
O. 1
0706
(TO
RQ
UE
TU
BE
, 19"
)FO
R 9
18, U
SE
PA
RT
NO
. 010
66 (T
INE
CO
VE
R, 9
18)
FOR
918
, US
E P
AR
T N
O. 0
3040
-51
(DE
CA
L, "
918"
)FO
R 9
18, U
SE
PA
RT
NO
. 112
81 (T
INE
SH
AFT
, 918
)P
AR
T N
O. 0
5063
-24
IS A
SE
T O
F 24
PIE
CE
S.
PA
RT
NO
. 031
96-1
2 IS
A S
ET
OF
12 P
IEC
ES
.P
AR
T N
O. 0
5074
-24
IS A
SE
T O
F 24
PIE
CE
S.
27
RE
F.Q
TY.
PA
RT
NO
.D
ES
CR
IPT
ION
11
1127
9T
INE
SH
AF
T2
1605
061
HH
CA
P S
CR
EW
, 7/1
6-20
NF
X 1
G8
ZIN
C3
805
063
HH
CA
P S
CR
EW
, 7/1
6-20
NF
X 1
-1/4
G8
ZIN
C4
1203
196
TIN
E, R
EV
ER
SIB
LE5
103
928
SO
FT
PLU
G, 1
-1/4
DIA
61
1127
8T
INE
MO
TO
R H
UB
, SP
LIN
ED
724
0507
4N
UT
, 7/1
6-20
NF
G8
ZIN
C8
103
930
SE
AL,
CR
197
639
1405
071
NU
T, N
YLO
CK
, 5/1
6-24
NF
ZIN
C10
101
067
TIN
E M
OT
OR
MO
UN
T &
LH
SID
E P
LAT
E11
1405
052
HH
CA
P S
CR
EW
, 5/1
6-24
NF
X 3
/4 G
5 Z
INC
122
0304
0-04
DE
CA
L, "
GR
EA
SE
DA
ILY
"13
105
282
PIP
E N
IPP
LE, 1
/8"
X 5
LO
NG
141
0520
4P
IPE
CO
UP
LER
, 1/8
" 15
105
256
GR
EA
SE
ZE
RK
, 1/8
NP
T16
105
607
SN
AP
RIN
G, S
H-1
56, 1
-9/1
6" E
XT
ER
NA
L17
103
001
O-R
ING
, 2-1
52, 3
-7/1
6 O
D X
3/3
2 S
EC
TIO
N18
1
046
05-F
TIN
E M
OT
OR
192
0558
5S
H C
AP
SC
RE
W, 1
/2-1
3 N
C X
1-1
/4 G
5 Z
INC
202
0392
6O
-RIN
G, 2
-112
N90
, 11/
16 O
D X
3/3
2 S
EC
TIO
N21
105
603
SN
AP
RIN
G, H
O-3
15, 3
-5/3
2 IN
TE
RN
AL
221
0394
3B
ALL
BE
AR
ING
, SK
F 6
208
236
0505
6H
H C
AP
SC
RE
W, 3
/8-2
4 N
F X
1 G
5 Z
INC
241
0206
5M
AN
IFO
LD, T
INE
MO
TO
R25
405
572
SH
CA
P S
CR
EW
, 5/1
6-18
NC
X 1
G5
ZIN
C26
204
520
FIT
TIN
G, 6
400-
8-8
272
0330
2F
ITT
ING
, 640
9-6
PLU
G28
605
072
NU
T, N
YLO
CK
, 3/8
-24
NF
ZIN
C29
110
702
TO
RQ
UE
TU
BE
, 17"
BO
LT O
N30
405
046
NU
T, G
RIP
CO
, 1/2
-13
NC
G5
ZIN
C31
405
067
HH
CA
P S
CR
EW
, 1/2
-13
NC
X 1
G5
ZIN
C32
110
067
TIN
E C
OV
ER
, 916
331
0334
1-22
DE
CA
L, "
TIL
LER
OP
ER
AT
ING
INS
TR
UC
TIO
NS
"34
103
341-
23D
EC
AL,
"T
ILLE
R S
AF
ET
Y IN
ST
RU
CT
ION
S"
352
0509
2H
H C
AP
SC
RE
W, 3
/8-1
6 N
C X
1-1
/2 G
5 Z
INC
362
0507
3N
UT
, NY
LOC
K, 3
/8-1
6 N
C Z
INC
371
0109
9H
AN
DLE
, DE
PT
H B
AR
381
0301
8G
RIP
, 1/8
X 3
/4 X
2-3
/439
103
080
SP
RIN
G40
101
018
PIN
, DE
PT
H B
AR
411
0306
5H
AIR
SP
RIN
G C
OT
TE
R #
442
103
040-
02D
EC
AL,
"B
AR
RE
TO
", 3
-1/2
X 1
1-1/
443
103
040-
01D
EC
AL,
"M
AD
E IN
US
A"
441
0304
0-08
DE
CA
L, "
WA
RN
ING
" (Y
ELL
OW
)45
103
040-
03D
EC
AL,
"C
AU
TIO
N"
(BLA
CK
& W
HIT
E)
461
0304
0-07
DE
CA
L, "
CA
UT
ION
" (Y
ELL
OW
)47
104
340
DE
CA
L, "
916"
RE
F.Q
TY.
PA
RT
NO
.D
ES
CR
IPT
ION
481
0504
4G
RE
AS
E Z
ER
K, 1
/4-2
8 U
NF
491
1014
6S
IDE
PLA
TE
, RH
TIN
E S
EC
TIO
N50
105
059
HH
CA
P S
CR
EW
, 3/8
-16
NC
X 1
G5
ZIN
C51
105
083
WA
SH
ER
, 7/1
6 U
SS
ZIN
C52
205
103
WA
SH
ER
, 3/8
A32
5 H
AR
DE
NE
D Z
INC
531
1014
4O
UT
BO
AR
D B
EA
RIN
G A
SS
EM
BLY
541
0500
6R
OLL
PIN
(S
LOT
TE
D S
PR
ING
), 3
/8 X
1-1
/2 Z
INC
551
0101
2D
EP
TH
BA
R
NO
TES:
1. R
IM A
LON
E IS
PAR
T N
O. 0
3712
.TI
RE
ALO
NE
IS P
ART
NO
. 031
93.
2. U
SAG
E: 1
0F
0025
6 R
1 PE
R 9
12, 9
16 &
918
.
4
10
9
65
7
811
2
3
4
1
1
2
1 2
FOR
TR
EN
CH
ER
, 031
90-F
W IS
ON
RIG
HT
SID
E, F
OR
TRE
NC
HIN
G IN
RE
VE
RS
E
FOR
TR
EN
CH
ER
, 031
91-F
W IS
ON
LE
FT S
IDE
, FO
RTR
EN
CH
ING
IN R
EV
ER
SE
RE
FQ
TY.
PA
RT
NO
.D
ES
CR
IPTI
ON
12
0226
9-H
UB
WH
EE
L H
UB
AS
SY
, 1-1
/8" B
OR
E2
103
190-
FWTI
RE
& R
IM, 1
6" X
4",
LEFT
HA
ND
31
0319
1-FW
TIR
E &
RIM
, 16"
X 4
", R
IGH
T H
AN
D4
605
042
NU
T, L
UG
, 1/2
-20
NF
52
0206
8P
IN, F
RE
E W
HE
ELI
NG
62
0510
2W
AS
HE
R, 1
/2 S
AE
ZIN
C H
AR
DE
NE
D7
405
548
RO
LL P
IN (S
LOTT
ED
SP
RIN
G),
1/8
X 3
/4 Z
INC
82
0335
2S
PR
ING
, CE
NTU
RY
338
59
402
083
SP
AC
ER
, WH
EE
L10
201
077
MO
UN
TIN
G P
LATE
, PIN
, FR
EE
WH
EE
LIN
G11
203
550
SP
LIT
RIN
G-2
7
DW
G#
PRO
DU
CT
LIN
E: C
OM
MO
NSC
ALE:
1:4
TITL
E:
SHEE
T 1
OF
1
FREE
WH
EELI
NG
HU
BSAN
D W
HEE
LS
0025
6 R
1DAT
E: 7
/16/
07
1014
4D
WG
#
PR
OD
UC
T LI
NE
: CO
MM
ON
SC
ALE
: 1:2
TITL
E:
SH
EE
T 1
OF
1
4 B
OLT
OU
TBO
AR
D B
EA
RIN
G A
SS
EM
BLY
,
DA
TE:3
/2/0
4
5
12
3
4
6
RE
FQ
TY.
PA
RT
NO
.D
ES
CR
IPT
ION
11
1014
2O
UT
BO
AR
D B
EA
RIN
G H
OU
SIN
G, 4
BO
LT2
101
026
SH
IELD
, OU
TB
OA
RD
BE
AR
ING
32
0304
3B
ALL
BE
AR
ING
, 620
54
105
024
SN
AP
RIN
G, H
O-2
00, 2
" IN
TE
RN
AL
51
0390
4O
-RIN
G, 2
-035
, 2-3
/8 O
D X
1/1
6 S
EC
TIO
N6
405
059
HH
CA
P S
CR
EW
, 3/8
-16
NC
X 1
G5
ZIN
C
2
3
4
5
1
6
RE
F.Q
TY.P
AR
T N
O.
DE
SC
RIP
TIO
N1
104
555
FIT
TIN
G, 6
801-
4-4
21
0421
4F
ITT
ING
, JS
-4-4
, HO
SE
BA
RB
1/4
X 1
/4 S
WIV
EL
31
1134
8H
OS
E, 1
/4 IN
CH
GA
SO
LIN
E, 4
L5, 3
-1/2
" LO
NG
42
0306
2-06
CLA
MP
, 1/4
" F
UE
L LI
NE
51
0451
6B
RE
AT
HE
R, F
ILT
ER
SN
AP
PE
R 1
435
61
1134
7H
OS
E, 1
/4 IN
CH
GA
SO
LIN
E, 4
L5, 3
-1/4
" LO
NG
SC
ALE
: 1:1
.3
TITL
E:
SH
EE
T 1
OF
1
BR
EA
THE
R H
OS
E A
SS
EM
BLY
DW
G#
PR
OD
UC
T LI
NE
: 916
D
ATE
: 4/2
6/07
1018
9 R
2
HOSES, 916 TILLER
QTY. PART NO. DESCRIPTION1 10204 HOSE, PUMP TO ACTUATOR TEE FITTING1 10205 HOSE, CONTROL VALVE TO ACTUATOR TEE FITTING1 10206 HOSE, CONTROL VALVE TO OIL FILTER MOUNT1 10207 HOSE, CONTROL VALVE TO WHEEL DRIVE MOTOR FRONT PORT1 10208 HOSE, CONTROL VALVE TO WHEEL DRIVE MOTOR REAR PORT1 10209 HOSE, CONTROL VALVE TO TINE MOTOR FRONT PORT1 10210 HOSE, CONTROL VALVE TO TINE MOTOR REAR PORT
916 HOSES.xls