8Series-CrazyPatchPillow

8/6/2019 8Series-CrazyPatchPillow

1/13

2010 BERNINA of America, Inc. jpl Page 1 of 13

Supplies

Created by Jeanne Delpit

This pretty patchwork pillow sampler includesinstructions for a variety of embellishmenttechniques stitched on BERNINA 8 Seriesmachines.

Crazy PatchPillow

Machine & Accessories BERNINA 820 or 830 Sewing Machine Automatic Buttonhole Foot #3A Zipper Foot #4D Edgestitch Foot #10D (optional) Open Embroidery Foot #20C and#20D 3-Groove Cording Foot #22 Patchwork Foot #37D Clear Embroidery Foot #39C or #39D BERNINA Stitch Regulator #42 8mm Double Cord Foot #60C Supplemental Thread Holder (optional)

Pillow Supplies Assorted fat quarters for front One 16 x 16 square of chamois, heavy

muslin, quilt batting for front base Two 13 x 15 rectangles of fabric for back

Four 2 x 43 strips of fabric for cording 4 yards of cotton home dec cording Two 3 x 15 strips of lightweight fusible interfacing Decorative cords, yarns, and threads to embellish

patchwork blocks One 14 pillow form Three buttons, diameter 50-weight cotton thread for piecing Assorted decorative threads to coordinate or con-

trast with fabrics and decorative cords/yarns

Notions 14 x 14 and 7 x 14 Cut for the Cure rulers Rotary cutter and mat Tracing wheel Fabric marker Parchment paper, 16 x 16 or larger Seam sealant Mary Ellens Best Press #80/12 Jeans needle 3.0 Double needle Hand-sewing needle 505 Quilt Basting Spray Buttonhole Cutter and Block

Visitwww.berninausa.com today!

Projects Webinars Promotions
http://www.berninausa.com/http://www.berninausa.com/http://www.berninausa.com/http://www.berninausa.com/http://www.berninausa.com/


2/13


Prepare your Personal Program withstitches to use on your crazy patchwork.

Select stitch #414 andtouch the Stitch AlteringArea (the blue space

around the stitch).

Select Add to PersonalProgram.

Select PersonalProgram 1.

Touch the title bar torename your PersonalProgram.

Touch the back arrow toremove the 1, then type

in Crazy Patch. Touchthe green checkmark toconfirm your selection.

Touch the flashing stitch#414 to add it to yourPersonal Program.

Select the decorativestitch menu and addmore stitches to yourPersonal Program.

You wont have to namethe folder again justtouch the Crazy PatchPersonal Program toadd new stitches to it.

After adding as manystitches as desired,touch the PersonalProgram Menu iconto see and access thestitches you have saved.

Assemble the Pillow Front Lay your crazy patch fabrics on the base fabric

and arrange as desired. Press all of the folds inplace.

Slice the parchment paper between the patch-work fabrics and the base fabric. Using a tracingwheel and a ruler, mark along the creased fold ofeach fabric piece. Remove the patchwork fabricsand draw over the incised lines.


3/13


Embellishment TechniquesCouched Cording Select three cords to couch. Thread the needle

and bobbin with coordinating fabric if you do notwish the stitches to show.

Attach 3-Groove Cording Foot #22 to the ma-chine and open the clasp on the front of the foot.

Tie the ends of the cords together. With theknotted end behind the foot, position the cords inthe grooves and close the clasp. If needed, usetweezers to pull the cords straight from the backof the foot.

Select decorative stitch #17 (or desired stitch);adjust stitch length and width as desired.

Couch the cords over the seam line, startingand ending beyond the ends of the placementline so that the starting and ending points will beconcealed in the pillow seam allowances.

Position the first crazy patch fabric face up in thecenter of the base fabric.

Position the second piece on top of the first, rightsides together, placing the creased fold along thepreviously marked line.

Insert a Jeans needle into the machine, attachPatchwork Foot #37D, and engage Dual Feed.Thread the bobbin for balanced tension.

Carefully open the fold of the second fabric.Stitch along the creased/marked line usingStraight stitch #1.

Trim the excess fabric away from the seam,leaving about seam allowance.

Fold the second layer back over the seam allow-ance; press.

Embellish the seam with one of the techniquesthat follow.


4/13


Touch the Security Program icon. Select3.0 Twin needle and touch Check toconfirm your selection.

Double Needle Stitching Select two threads and place them on the Thread

Delivery System corresponding spindles.

Thread the bobbin for balanced tension.

Insert a Double needle into the machine. Placeone thread in the threading path so that the firstsensor is activated. When the animation appears,touch the Manual Threading icon on the screen.This will prevent the Auto Needle Threader fromactivating when you touch the illuminated AutoNeedle Threader button.

Place the thread into the appropriate threadingguides, but do not thread it through the needle;let it fall onto the stitch plate after passing itthrough the final guide on the needle bar.

Touch the illuminated Auto NeedleThreader button; even though youwill be threading manually, thisstep is necessary to seat the threadcorrectly for stitching.

Repeat this process for the second thread, mak-ing sure you touch the Manual Threading iconand later the Auto Needle Threader icon.

Thread the needles using the Manual Threadincluded with the BERNINA 8 Series machines.

Tip: Place the presser foot in the up position foreasier threading.


5/13


Select your Crazy Patch Personal Program andselect stitch #414. Notice that the stitch width hasbeen reduced so that the needles will not hit thepresser foot. Note that the Security icon is nowred, indicating that it is engaged.

Attach Open Embroidery Foot #20C or #20D tothe machine and note the groove in the foot.

Stitch over the seam line, aligning the seam withthe groove in the center of the foot.

After embellishing the seam, remove the Double

needle.

To disengage the Double needle limitation, touchthe Security Program icon, select the singleneedle, and touch the check mark. The SecurityProgram does not automatically return to defaultwhen the machine is turned off or when a newstitch is selected.

Bobbin Play Wind the heavy decorative

threads onto Jumbobobbins. Decrease theBobbin Winding MotorSpeed to its lowest setting.

Tip: Consider using asupplemental threadholder so the decorativethread can spill of thecone without twisting.

Tip: Consider windingtwo bobbins of the samethread if you have longseams to embellish.

Remove the bobbin. With your left hand pressingup on the bottom of the retaining finger to keepthe bobbin case in place, turn the handwheelto position the bobbin basket so that the Multi-function Tool rests comfortably on the silver lug.


6/13


Pressing down securely with the MultifunctionTool, move the silver lug 3-4 clicks to the left toloosen the bobbin tension. The number of clickswill vary depending on the size of the decorativethread and your machine.

To reseat the bobbin basket, close the bobbinarea door with NO bobbin inserted. Open thebobbin area door and insert one of the bobbinswound with heavy decorative thread.

Insert a Jeans needle into the machine. Threadthe needle with the thread used for seaming thepatchwork. Increase the needle tension to about9 (this will vary depending on the thread and yourmachine.)

Open your Crazy Patch Personal Program andselect a decorative stitch. Some fun stitches are:#133, #601, #603, #605, #656, #672, #699, #711,#738, #1119, and #1332, as well as many of theQuilt Block Menu stitches.

Depending on the stitch chosen, attach OpenEmbroidery Foot #20C or #20D, or Clear Embroi-dery Foot #39C or #39D. Edgestitch Foot #10Cor #10D may be used for some stitches, but theymust be light and open so the foot will not dragover the stitching.

Prepare a text swatch by cutting 10 x 12rectangles of base fabric and patchwork fabricand stacking them. Draw parallel lines about1 apart on the wrong side of the fabric sandwich(on the base fabric).

Place the right side of the test fabric sandwichface down on the machine so that the wrong sideis facing up. Sew lines of different decorativestitches on the marked lines. Check the resultsas you stitch, adjusting the needle or bobbin casetension as needed to obtain optimal results. Notethe adjustments by writing on the wrong side ofthe test pieces.

Place the patchwork pillow front face down onthe machine, with the base fabric on top. Selecta bobbin play stitch and adjust the settings asdetermined on the test swatch. Sew along the

seam line, stopping outside the seam allowancefor the next patch so the ends will be concealed.Stitch additional rows as desired.


7/13


Twisted Thread Embellishment Attach Open Embroidery Foot #20C to the

machine, insert the Jeans needle, and threadthe needle and bobbin with a color to blend orcontrast with the twisted threads.

Select stitch #32, the Single Straight stitch, andengage Pattern Repeat 1x. Engage Needle StopDown.

Touch the Set Up soft key and selectthe Sewing Settings icon.

Scroll to the third page of this menu to access theHover options. Select the Hover at AdjustablePosition icon and set the hover height to 3.0mm.Touch the check mark to confirm.

Touch the red X to escape Set Up.

Increase the stitch length to about 4.0mm or longenough to take a single stitch over the decorativecords/yarns you have selected.

Select 2-5 decorative yarns or cords; bundlethem together and tie a knot at the end. Split theyarns into two halves you may choose to haveone or two strands on each side, two on one sideand three on the other, etc.

Position the presser foot at the beginning of theseam and hand-walk the needle into the centerof the seam allowance. Leave the presser footraised.

Place the divided yarns behind and around theneedle and lower the presser foot.

Select Zigzag stitch #2. Drop the feed dog andstitch in place 6-7 times right in front of the knotto hold the bundle in place.


8/13


Select Single Straight stitch #32 again. Note thatall of the changes made previously have beenremembered.

Take a stitch. The needle will stop down in thefabric and the foot will hover above it.

Cross the yarns over each other and pull themsnug against the needle. If needed, adjust thestitch length to catch all of the yarns between theyarn crosses/twists.

Stitch again. Repeat the twisting/crossing proc-ess as needed to complete the row of stitching.Crossing in the same direction each time willproduce a braided look.

This technique takes some time to stitch, asonly one stitch is sewn at a time. You could usethe Free Hand System to lift the presser footafter each stitch, but isnt it easier to have themachines hover function do it for you?

When finished with this technique, go back intoSet Up > Sewing Settings > Hover Options and

touch the Reset icon to restore the default hoversetting.

Free Form CouchingIf using decorative threads that will not couchnicely, or if you do not want to lose the look of thethreads by couching them down, consider securingthem in place randomly.

Gather some decorative cords/yarns/threadstogether to form a single strand. Place thestrand over the crazy patch seamline to beembellished.

Select Bartack #25.

Insert a #80/12 Jeans needle into the machine.Thread the needle and bobbin with coordinatingor contrasting thread as desired, threading thebobbin for balanced tension.

Attach Open Embroidery Foot #20C and placethe end of the strand under the foot. Leave along enough tail that the cord ends will be hiddenunder the seam allowance of another patch.

Lower the presser foot and stitch the bartack tohold them in place, using tweezers to keep thecords together if needed. If a larger bartack isneeded, increase the stitch width.


9/13


Create freeform loops with the decorative cords,bartacking in place periodically.

When finished, leave the thread tails long enoughthat they will be concealed under another patch.

BERNINA Stitch Regulator EmbellishmentThis isnt necessarily a seamline embellishment,but it works well to enhance the crazy patch blocks.

Insert a #80/12 Jeans needle into the machine.Thread the needle and bobbin with contrastingor coordinating thread. Thread the bobbin forbalanced tension.

Select one of the BERNINA Stitch Regulatorsoles and install it on the accessory.

Attach the BERNINA Stitch Regulator to themachine and plug it in.

Select your preferred Mode and alter the stitchlength as desired. The stitch width can be alteredwhen using Straight stitch #1, or Zigzag stitch #2can be selected instead.

Using the Start/Stop button or the foot control,activate the BERNINA Stitch Regulator and beginmoving the fabric.

Stitch, following a line in the fabric pattern orcreating your own stitch designs.

Activate the Auto Thread Cutter when your stitchpatch is complete.

The BERNINA Stitch Regulator can also becombined with the Bobbin Play and Twin Needleembellishment techniques.


10/13

2010 BERNINA of America, Inc. jpl Page 10 of

Assemble the Pillow Back Place the two 12 x 15 rectangles right side

down on an ironing board so that the edges forthe placket and buttonholes are next to eachother. Fuse the 3 x 15 interfacing strips to these

edges.

Fold back 1 along the fused edge and pressin place. Fold under another 1 to completelyenclose the interfacing; press in place.

Turn the back pieces right side up and overlapthe hemmed edges 1.

Mark the buttonhole locations: one in the center,one between the center and each side.

Attach Automatic Buttonhole Foot #3A to themachine. Thread the #80/12 Jeans needle andbobbin with the thread for the buttonholes.Thread the bobbin for balanced tension.

Select buttonhole #52, the Heirloom Buttonhole,from the Buttonhole Menu.

Touch the Buttonhole Length/Measurement icon.Hold your button up to the left side of the screenand use the stitch length or stitch width knob tomove the vertical line until it reaches the rightside of your button.

Notice that the measurements on the graphicchange as you move the line. The upper numberis the size of the button; the lower one is the sizeof the buttonhole. 2mm is automatically added tothe length to allow for the thickness of the button.

Touch the green checkmark to confirm the size.

The Heirloom buttonhole is delicate; to avoidaccidentally cutting the stitches when opening it,touch the Buttonhole Slit Adjustment, and thenchange the slit size to 1mm.


11/13


When the slit size is increased, the bead size isautomatically reduced. Watch it change as youadjust the slit width. Adjust the bead width to4.2mm; this will not interfere with the slit width.

Sew a test buttonhole using the same layers theactual buttonhole will be stitched throughthreelayers of fabric and one layer of interfacing.Touch the Buttonhole Length/Measurement icon,if needed, and remeasure the button. Retest.

Align the edge of the pillow back under AutomaticButtonhole Foot #3A, positioning the outer edgeof the fabric along the line in the stitch platebehind the foot. Press the Presser Foot Raise/Lower button on your machine; this will lower thepresser foot, but then raise it again slightly tohover over the fabric. Fine tune the placement.

Stitch the buttonhole using the Start/Stop buttonor the foot control. Do not move the fabric untilthe buttonhole is complete. Use the Auto ThreadCutter to clip the threads.

If desired, use a seamsealant on your buttonholes,applying it to the wrong side.Allow it to dry, then use aButtonhole Cutter & Block tocut the buttonholes open.

Overlap the pillow backs withthe buttonholes on top. Markthe buttonhole locationsthrough the buttonhole slits.

Attach Button Sew-On Foot #18 and selectButton Sew-On stitch #60. Notice that the feeddog automatically drops and that stitch lengthadjustment is not available.

If desired, change the needle thread for your but-tonholes.

Place the button underthe foot with the holesbetween the toes ofthe foot. The holes in

buttons are not alwaysspaced the same, soalways test first, usingthe handwheel stitch inthe left hole, then jumpto the right. Adjust thestitch width as needed to match the button holes.Slowly complete the stitch program using the footcontrol. When done, use the Auto Thread Cutterto trim the thread tails.


12/13


Stitch the remaining buttons in place. It is notnecessary to test the stitch width again.

Button the pillow backs together. Mark a 15 x 15square using a 14 square ruler and fabric marker.Trim along the marked lines with a rotary cutterand mat.

Set the pillow back aside for now.

Make and Attach the Cording Thread the #80/12 Jeans needle and bobbin

with coordinating threads. Thread the bobbin for

balanced stitching.

Cut the ends of the 2 x 43 strips at 45. Using seam allowances, join them together to formone long strip. Trim the seam allowances to and press them all in the same direction.

Wrap the fabric strip around the cording startingat one end. Pin edges if necessary.

Attach Zipper Foot #4D and engage the Dual Feedfeature. Engage Needle Stop Down. Move theneedle one position from far left. This line of stitch-ing will not be tight against the cording, as the fab-ric needs to be loose so that it can be shirred alongthe cord.

Begin stitching. After 12 or so, stop and shirr thefabric along the cord. Continue stitching, stoppingand shirring as needed. When finished, adjust theruching evenly along the length of cord.

Lay the pillow front right side up on a flat surface.Pin the cording around the outer edges of thepillow front, matching raw edges. Start and stopin the middle of one side. Adjust the gathers at thecorners so that there is enough ease for the cornerto turn right side out easily. Pin the covered cordin place.


13/13

Visit www.berninausa.comfor additional projects and information.

Tip: To make removing the pins easier, pin in theseam allowance with the points facing the presserfoot.

Attach 8mm Double Cord Foot #60C. EngageNeedle Stop Down. Position the pillow front sothat the left groove of the presser foot rests onthe cording. Thread the needle and bobbin withmatching thread. Adjust the needle position sothat the needle will stitch on the previous stitching.This seamline will be close to from the edge.As you stitch the section where the ends meet,pull the cording slightly out of the ruched coveringand trim the ends to remove the bulk.

Fold the seam allowances away from the pillowand check to make sure the ruched cord turns thecorners nicely and that there are no puckers in thepillow top.

Join the Pillow Front and Back Place the pillow back on a flat surface, with the

right side facing up. Decide whether the buttonedclosing will run across or up and down and placethe pillow front face down on the pillow backaccordingly. Pin the front layers to the back.

Thread the #80/12 Jeans needle and bobbinwith coordinating thread. Thread the bobbin forbalanced tension. Engage Needle Stop Down.

Attach Zipper Foot #4D to the machine andengage the Dual Feed feature. Position the pillowunder the presser foot with the wrong side of thefront facing up so that the previous stitching isvisible.

Position the left edge of Zipper Foot #4D as closeto the cord as possible. Stitch around all four sidesof the pillow, placing the new stitching just to theleft of the previous stitching (see the red line); thisensures that the previous stitching will be hiddenwhen the pillow cover is turned right side out.

Reach inside the pillow cover and unbutton thebuttons. Turn the pillow cover right side out andadjust the ruched cording at each corner. Insert thepillow form and button the opening closed.

8Series-CrazyPatchPillow

Documents

Transcript of 8Series-CrazyPatchPillow