(8) Ore Processing (Beneficiation)
Transcript of (8) Ore Processing (Beneficiation)
-
8/12/2019 (8) Ore Processing (Beneficiation)
1/31
Mineral dressing
(= Ore beneficiation)The first process most ores undergo after t
the mine is mineral dressing (processingcalled ore preparation, milling, and ore dore beneficiation.
Ore dressing is a process of mechanically the grains of ore minerals from the gangminerals, to produce a concentrate (enric
portion) containing most of the ore minetailing (discard) containing the bulk of tminerals.
-
8/12/2019 (8) Ore Processing (Beneficiation)
2/31
-
8/12/2019 (8) Ore Processing (Beneficiation)
3/31
-
8/12/2019 (8) Ore Processing (Beneficiation)
4/31
Mineral dressing
Since most ore minerals are usuadisseminated and intimately associgangue minerals, the various mineral
broken apart (freed) or liberatedbefor
be collected in separate products.
Therefore, the first part in any ore dressiwill involve the crushing and grindingalso known by a common namcomminution
) of the ore to a point wmineral grain is practically free.
-
8/12/2019 (8) Ore Processing (Beneficiation)
5/31
Crushin
-
8/12/2019 (8) Ore Processing (Beneficiation)
6/31
Comminution
Crushing and grinding are usually carried out in a seoperations by which the lump size is reduced step byare 3 stages of crushing and 2 stages of grinding.
i. Primary Crushing (coarse crushing): In primarore or run-of-mine ore (up to 1 m in size) is crushabout 10 cm and it is done in a jaw or gyratory cr
ii. Secondary Crushing (intermediate crushing): Iore is crushed from 10 cm to less than 1 2 cm sipurpose jaw, cone or roll crushers are used. Thescrushers consume more power than primary cru
iii. Tertiary Crushing (fine crushing): By tertiaryis crushed from 1 2 cm to less than 0.5 cm. Shorcrushers, roll crushers, hammer mills can be usedpurpose.
-
8/12/2019 (8) Ore Processing (Beneficiation)
7/31
Comminution The two stages of grinding are:
i. Coarse Grinding: Rod mills are generallygrinding machines. They are capable of takas 50 mm and making a product as fine as 3
ii. Fine Grinding: Fine grinding, which is thcomminution, is performed in ball mills usinthe grinding medium. The ball mill, after fematerial may give a product that is less thanGrinding is usually done wet.
The principle purposes of grinding are:
i. To obtain the correct degree of liberation in minera
ii. To increase the specific surface area of the valuablhydrometallurgical treatment; i.e. leaching.
-
8/12/2019 (8) Ore Processing (Beneficiation)
8/31
The mills
-
8/12/2019 (8) Ore Processing (Beneficiation)
9/31
Sizing Methods There are two methods of industrial sizing.
i. Screening
ii. Classification
Screening is generally carried out on relatively coarse mefficiency decreases rapidly with fineness. Screening is gmaterials above about 250 microns in size, finer sizing nundertaken by classification.
Classification: Classification is defined as a method of seof mineral particles into two or more products accordinvelocities in water, in air or in other fluids as given in beIndustrial classification may be carried out in different tand these classifiers are; hydraulic classifiers, mechanic
cyclones. Basically they all work according to the principare suspended in water which has a slight upward moveparticles. Particles below a certain size and density are cthe water-flow, whereas the coarser and heavier particle
-
8/12/2019 (8) Ore Processing (Beneficiation)
10/31
Concentration The second fundamental (main) operation in mineral pr
release, or liberation, of the valuable minerals from the the separation of these values from the gangue, i.e. conce
Concentration is usually accomplished by utilizing somein physical (or chemical) properties of the metal and ganthe ore.
In concentration the following terms are used:
Head is the feed to a concentrating system.
Concentrate is defined as the valuable mineral(s) separaundergoing a specific treatment.
Tailing is the fraction of ore rejected in a separating provalueless portion, i.e. discard or waste.
Middlings are the particles of locked valuable mineral aliberation has not been attained. Further liberation can further comminution.
Recovery is the percentage of the total metal, contained recovered in the concentrate.
-
8/12/2019 (8) Ore Processing (Beneficiation)
11/31
Physical Concentration Meth
1. Separation dependent on optical and radioactive propi.e. hand pickling, optical sorting, radioactive sorting, et
2. Separation dependent on specific gravity (density) difi.e. heavy-media separation, gravity concentration by uscones, etc.
3. Separation utilizing the different surface properties (ichemistry) of the minerals, i.e. froth flotation, etc.
4. Separation dependent on magnetic properties of the mhigh, dry and wet magnetic separation, etc.
5. Separation dependent on electrical conductivity propeminerals, i.e. electrostatic separation, etc.
-
8/12/2019 (8) Ore Processing (Beneficiation)
12/31
Tyler screen scale starts with 1.05 inch (26.67 mm), for small
dimensions are usually given in microns (1 micron = 10-3 mm
(#) is equal to 74 microns in the Tyler Screen S
-
8/12/2019 (8) Ore Processing (Beneficiation)
13/31
Pretreatment Processes
i. Drying
ii. Calcination
iii. Roasting
iv. Agglomeration
-
8/12/2019 (8) Ore Processing (Beneficiation)
14/31
Pretreatment Processes
Drying
Drying usually means the removal of mechanically held water concentrate, or other solid materials by evaporation, i.e. expusually done in a drying furnace (fixed or fluidized bed, or k
-
8/12/2019 (8) Ore Processing (Beneficiation)
15/31
Calcination
Calcination is the thermal treatment of an ore or a concdecomposition and the elimination of a volatile product,vapor, or other gases.
Therefore, by contrast with drying, calcination involves CO2, etc., which are chemically bound as e.g. hydrates o
Temperature necessary for the
decomposition pressure to reach 1 atm
varies, e. g.
FeCO3 and Mg(OH)2 ; T 200C
MnCO3 , MgCO3 ; T 400C
CaCO3 ; T 900C
BaCO3 and Na2CO3; T 1000C
-
8/12/2019 (8) Ore Processing (Beneficiation)
16/31
Calcination
-
8/12/2019 (8) Ore Processing (Beneficiation)
17/31
Roasting
Roasting is the oxidation of metal sulfides to give medioxide.
-
8/12/2019 (8) Ore Processing (Beneficiation)
18/31
Temperature of Roasting
Troast > 500 - 600C: in order for the reactions to occur with sufficien
Troast < 1000C: roasting is usually carried out below the melting poi
sulfides and oxides involved and to avoid ferrite formation.Dead roast or sweet roast: Roasting to completion with the elimination
overall reaction.
Partial roasting: Removal of some of the sulfur by roasting.
e.g. partial roasting of copper concentrates
CuFeS2 + 4O2 = CuSO4 + FeSO4
2CuS + 7/2O2 = CuO.CuSO4 + SO2
Types of Roasting
1. Oxidizing roast
2. Volatilizing roast
3. Chloridizing roast
4. Sulfating roast
5. Magnetizing roast
6. Carburizing roast
7. Sinter or Blast roasting
-
8/12/2019 (8) Ore Processing (Beneficiation)
19/31
Agglomeration
When the particle size of an ore or concentrate is too small for u
a later stage of treatment, i.e. in the blast furnace, it must be refo
into lumps of appropriate size and strength that is agglomerated
Types of agglomeration
i. Sintering
ii. Pelletizing
iii. Briquetting
iv. Nodulizing
-
8/12/2019 (8) Ore Processing (Beneficiation)
20/31
Extraction via Flotatio
Froth flotation - a process where valuable minerals are separated frominducing them to gather on the surface of a froth layer. This process is based on the ability of certain chemicals to modify the surf
mineral(s).
Other chemicals are used to generate the froth and still others are used to a
The process of froth flotation involves crushing and grinding the ore t This separates the individual mineral particles from the waste rock and oth
The grinding is normally done in water with the resultant slurry called the
The pulp is processed in the flotation cells. Here the pulp is agitated with a flotation mixture
Fine bubbles are introduced
The ability of a mineral to float depends upon its surface properties. Chemical modification of these properties enables the mineral particles to
bubble.
The air bubble and mineral particles rise through the pulp to the surface of
Even though the air bubbles often break at this point, the mineral remof the froth.
The mineral is physically separated from the remaining pulp material further processing.
-
8/12/2019 (8) Ore Processing (Beneficiation)
21/31
-
8/12/2019 (8) Ore Processing (Beneficiation)
22/31
Sulphide Minerals
Are sometimes roasted
Heated in air without melting to transformsulphides to oxides
Gives off H2S and SO2
Then oxides processed like Fe
Process of roasting and smelting together cre
matte
Sulfides are melted into a matte and air is
through. S is converted to sulfur dioxide
iron oxide, and Cu and Ni stay in melt Solvent extraction/electroplating
Used where rock contains Cu but in too l
amounts to be recovered by classical met
-
8/12/2019 (8) Ore Processing (Beneficiation)
23/31
-
8/12/2019 (8) Ore Processing (Beneficiation)
24/31
Heap Leaching
In this process, typically done for A
ore is not ground, but rather, crushe
piled on the surface.
Weak solutions of NaCN (0.05%) pthrough the material leaching out th
desired metals.
The solutions are collected and the
are precipitated
-
8/12/2019 (8) Ore Processing (Beneficiation)
25/31
Cyanide extraction for
Preparation ground into fine powder
mixed in solution of NaCN (sodium cyanide) & water
referred as SLURRY
Extraction Zinc powder is added to this gold-cyanide solution which precipitates ou
The mixture then goes thru a filter where the precipitate sticks to a heavy
later cleaned to remove the gold. Extreme heat is applied which burns off the Zn
ENVIRONMENT: Gold mines make sure that cyanide doesn't escape, by using containment s
the water.
Entire operation must be kept on the alkaline side HCN is volatile and p
ALTERNATIVE PROCESSES
Gold extraction by Mercury. Elemental Hg forms an amalgam with many and gold.
Mercury boiled off, precious metals remain.
Practised in Central America 1570-1900, and in Brazil until now.
-
8/12/2019 (8) Ore Processing (Beneficiation)
26/31
Cyanide in the beneficiation 0.05% NaCN solution is used to extract Au and Ag from o
Au dissolves by two processes occurring simultaneously oCathode
At one end of the metal, the cathodic zone, oxygen takes uundergoes a reduction reaction.
O2 + 2 H2O + 2 e- => H2O2 + 2 OH
-
Anode
At the other end, the anodic zone, the metal gives up electran oxidation reaction.
Au => Au+ + e-
Au+ + 2CN- => Au(CN)2-
And then form strong complexes by Elsener
s/ Adamson
s
4Au + 8NaCN + O2 + 2H2O = 4NaAu(CN)2 + 4NaOH
Or Adamsons 2nd reaction
2Au + 4NaCN +2H2O = 2NaAu(CN)2 + H2O2 + 2NaOH
-
8/12/2019 (8) Ore Processing (Beneficiation)
27/31
Heap Leach Process
-
8/12/2019 (8) Ore Processing (Beneficiation)
28/31
Solvent extraction of U from
-
8/12/2019 (8) Ore Processing (Beneficiation)
29/31
Smelting
-
8/12/2019 (8) Ore Processing (Beneficiation)
30/31
Potential Environmental Pro
A. Mining operation itself
Disposal of a large amount of rock an
Noise
Dust
Beneficiation
Smelting and refining
-
8/12/2019 (8) Ore Processing (Beneficiation)
31/31