SUMMARYvnit.ac.in/stores/wp-content/uploads/2019/12/schedule-b2-signed.pdf8 Excavation for...

Name of Work :- Construction of Engine laboratory for Mechanical & Metallurgy at VNIT Nagpur.

Sr. No. Description

(In figure) (in Words)

A Amount of Civil Work

B Amount of Credit Work

C Amount of Horticulture

D Amount of Electrical Work

Total (A+B+C+D) Amount in Rs.

Plus GST as applicable

Contractor Director

SUMMARY

Amount

(in figure) (in words)

1Dismantling brick masonry in lime or cement mortar and stackingthe materils as directed with all leads, lifts etc. 150 CUM

2Removing rich mix cement concrete including stacking the spoilsas directed with all leads, lifts etc, complete. 100 CUM

3Removing doors and windows with frames and stacking thematerials as directed with all leads, lifts etc. complete. 50 Nos

4Removing ventilators and small windows with frame and stackingthe materials with all leads, lifts etc. complete. 25 Nos

5Removing cement tiles, or marble or polished shahabad floor ordado without bed concrete including stacking the materials asdirected with all leads, lifts etc. complete

500 Sqm

6Removing A.C Sheet from roof and stacking as directed with allleads and lifts etc. complete. 500 Sqm

7 Dismantling steel work in built up sections without dismem bering and stacking within 50 meters lead 10 M.T

Rate in Rs.

VISVESVARAYA NATIONAL INSTITUTE OF TECHNOLOGY, NAGPUR.

S C H E D U L E -B

Name of work :- Construction of Engine laboratory for Mechanical & Metallurgy at VNIT Nagpur

Item no. Items of work Estimated Quantity Unit Amount

Part A- Civil Work

Page 1

(in figure) (in words)Rate in Rs.Item no. Items of work Estimated

Quantity Unit Amount

8 Excavation for foundation in earth, soil of all types, sand,gravel and soft murum, including removing the excavated materialup to a distance of 50 m. beyond the building area & stacking andspreading as directed, dewatering, preparing the bed for thefoundation and necessary back filling, ramming, watering includingshoring and strutting etc. complete. (Lift upto 1.5 m.) ByMechanical Means [Spec.No. : Bd.A. 1 Page No. 259]

1000 CUM

9 Excavation for foundation in hard murum including removing theexcavated material upto distance of 50 metres beyond the buildingarea and stacking and spreading as directed, dewatering,preparing the bed for the foundation and necessary back filling,ramming, watering including shoring and strutting etc. complete.(Lift upto 1.50 m) By Mechanical Means [Spec.No. : Bd.A. 2 PageNo. 259]

357 CUM

10 Excavation for foundation in Soft rock and old cement or limemasonry foundations including removing the excavated materialupto a distance of 50 metres beyond the building area andstacking as directed, including dewatering, preparing the bed forthe foundation and necessary back filling with availableearth/murum, ramming ,watering including shoring and struttingetc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means[Spec.No. : Bd.A. 4 Page No. 259]

177 CUM

11 Providing Preconstructional Antitermite Treatment as per I.S.6313 (Part-II) by treating the bottom surface and sides forexcavation clorophyriphoas / lendene at the rate of 5 liters ofemusion concentrates of 0.5 % of Aldrin per square meter ofsurface area covering 10 years guarantee.

800 SQM

Page 2



12 Providing pre-constructional Anti-termite treatment by treating thebackfill in immediate contact with foundation at the rate of 7.50litres of emulsion concentrate of 0.5 percent of chicropyriphox persquare metre of vertical surface area with ten years guaranteebond as per IS 6313 (Part-II) 1971

1010 SQM

13 Providing pre-constructional Anti-termite treatment by treating thebackfill in immediate contact with foundation at the rate of 7.50litres of emulsion concentrate of 0.5 percent of chicropyriphox persquare metre of vertical surface area with ten years guaranteebond as per IS 6313 (Part-II) 1971

1050 SQM

14 Filling in plinth and floors with approved excavated material in15cm to 20cm layers including watering and compaction etccomplete. [Spec.No. : Bd.A. 10 Page No. 262]

480 SQM

15 Providing & Filling in plinth and floors with contractor'sapproved material / murum / stone dust in 15cm to 20cm layersincluding watering and compaction etc complete. [Spec.No. :Bd.A. 11 Page No. 263]

443 CUM

16 Providing soling using 80 mm size trap metal in 15 cm. layer

including filling voids with Crushed sand/grit, ramming, watering

etc. complete. [Spec.No.: As directed by Engineer in charge.]

195 CUM

Page 3



17 Providing and laying in situ, cement concrete in M-15 of trap/granite/ quartzite/gneiss metal for foundation and beddingincluding bailing out water, formwork, compacting, polythene of 50micron below plinth slab and curing complete, with fully automaticmicro processor based PLC with SCADA enabled reversible DrumType mixer, With natural sand. [Spec. No. : Bd.E. 1/Page No.287]

217 CUM

18 Providing and casting in situ cement concrete M-15 of trap/granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed includingsteel centering, plywood/steel formwork compacting, rougheningthem if special finish is to be provided, finishing uneven andhoneycombed surface and curing etc. complete. The CementMortar 1:3 plaster is considered for rendering uneven andhoneycombed surface only. Newly laid concrete shall be coveredby gunny bag, plastic, tarpaulin etc. (Wooden centering will not beallowed.)[Spec.No.: Bd.E. 3/Page No.288/I.S. 456(2000)]

5 CUM

19 Providing and laying in situ cement concrete M-25 of trap / granite/quartzite/gneiss metal for R.C.C. work in foundations like raft,strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, coverblocks compaction and curing roughening the surface if specialfinish is to be provided (Excluding reinforcement and structuralsteel) etc. etc. complete, With fully automatic micro processorbased PLC with SCADA enabled reversible drum type concretemixer. With natural sand.[Spec.No: Bd.F.3 Page No. 298 andB.7,Page No.38)]

536 CUM

Page 4



20 Providing and casting in situ cement concrete M-25of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detaileddesigns and drawing or as directed including centering, formwork,cover blocks compaction finishing the formed surfaces withcement mortar 1:3 of sufficient minimum thickness to give asmooth and even surface or roughening if special finish is to beprovided and curing etc. complete. (Excluding reinforcement andstructural steel).With fully automatic micro processor based PLCwith SCADA enabled reversible drum type concrete mixer WithNatural sand.[Spec.No.: Bd.F.5 Page No.300 and B.7,Page.No.38]

72 CUM

21 Providing & casting in situ cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as perdetailed designs & drawings or as directed including centering,formwork, cover blocks compaction & roughening the surface ifspecial finish is to be provided & curing etc. complete. (Excludingreinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled concrete batch mixplant (pan mixer).... With natural sand. [Spec.No.: Bd.F.6 PageNo.300 and B.7,Page No.38]

205 CUM

22 Providing & casting in situ cement concrete M-25 of trap/ granite/quartzite/ gneiss metal for R.C.C. chajja as per detailed design &drawings including centering, formwork, cover blocks compacting ,curing , finishing & roughening the surface if special finish is to beprovided & curing complete. (Excluding reinforcement andstructural steel).With fully automatic micro processor based PLCwith SCADA enabled reversible drum type concrete mixer Withnatural sand. [Spec.No.: Bd.F.9 Page No. 303 and B.7,PageNo.38]

8 CUM

Page 5



23 Providing and casting in situ cement concrete in M-25 of trap/granite/ quartzite/gneiss metal for R.C.C. pardi of requiredthickness including centering, formwork, cover blocks compacting, curing , finishing & roughening them if special finish is to beprovided and curing complete. (Excluding reinforcement andstructural steel). With fully automatic micro processor based PLCwith SCADA enabled reversible drum type concrete mixer. withreversible Drum Type mixer with SCADA With natural sand.[Spec.No.: Bd.F.11 PageNo. 304 and B.7,Page No. 38]

2 CUM

24 Providing and casting in situ cement concrete M-25 of trap/ granite/ quartzite/gneiss metal for R.C.C. slabs and landings canopy asper detailed designs and drawings including centering, formwork,cover blocks compaction finishing the formed surfaces withcement mortar 1:3 of sufficient minimum thickness to give asmooth and even surface or roughening if special finish is to beprovided and curing etc. complete,(Excluding reinforcement andstructural steel).With fully automatic micro processor based PLCwith SCADA enabled reversible drum type concrete mixer Withnatural sand.[Spec.No.: Bd.F.8 Page No.302 and B.7,Page No.38]

23 CUM

25 Providing and laying in situ / ready mix controlled grade of M25 of trap /granite /quartzite /gneiss metal for RCC works in cut off walls / curtain walls including necessary scaffolding, centering, compacting by vibrator, finishing and curing etc. complete. (with fully automatic micro processor based PLC with SCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with natural /artifical sand, excluding reinforcement)

13 CUM

Page 6



26 Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 oF sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd. F. 13 Page No. 305 /I.S. 456:2000

14 Cum

27 Providing and fixing in position TMT / HYSD steel barsreinforcement of various diameters for R.C.C. pile caps, footings,foundations, slabs, beams and columns, canopies, staircases,newels, chajjas, lintels, pardies, coping, fins, arches etc. as perdetailed design and drawings and schedules including cutting,bending, hooking the bars, binding with wires or tack welding andsupporting as required completed. [Spec.No.: Bd.F.17/PageNo.306]

103.45 MT

28 Providing and fixing in position in R.C.C. slab during layingrectangular 2 mm thick M.S. Sheet iron box 180 mm x 100 mmand of required depth with holes or notches as required, bottomand top lids of 1.6 mm thick M.S. sheet fixed with 3.5 mm diaround head Screwed together with Fan dia.M.S. bar bent to shapewith hooked ends (for fan hooks) as per standard design includingpainting to exposed portion complete. [Spec.No.: As directed byEngineer- in-charge]

40 No

Page 7



29 Providing fly ash brick masonry with conventional / I.S. type flyash bricks in C.M. 1:6 in foundation and plinth including bailingout water manually striking joints, racking out joints watering andscaffolding etc. complete. [Spec.No.: As director by engineerincharge and BDG- 2 and 5]

438 CUM

30 Providing fly ash brick masonry with conventional/ I.S. type

bricks in cement mortar 1:6 in Superstructure including striking joints, raking out joints, watering and scaffolding etc. complete. As director by engineer incharge and BDG- 2 and 5

311 SQM

31 Providing Second class fly ash brick masonry with conventional

/ I.S. type bricks in cement mortar 1:4 in half brick thick wall

including mild steel longitudinal reinforcement of two bars of 6 mm

diameter / two hoop iron strips 25 mm x 1.60 mm at every third

course, properly bent and bounded at ends scaffolding raking out

joints and watering etc. complete. [Spec.No.:Bd. G. 7 Page 316]

7 SQM

Page 8



32 Providing waterproofing treatment to old terraces by removingexisting treatment, sealing of cracks by non shrink crack fillcompound applying first coat of polymer modified semiviscouspaste prepared by mixing polymer of approved make (such asMaster Seal 550/brush bond/roff Supercrete /Webercrete/Monobond / Perma shield / Hypercrate / Master (Crete) M 81)andcement in 1:2 proportion (1 liter polymer :2 Kg. Cement) orRohnex water proofing system in two coats ( 1 kg powder, 700 mlwater & polymer jelly for first coat & 1 kg powder, 500 ml water &polymer jelly for second coat) to a neatly cleaned and dust freeconcrete surface and upto 300 mm over parapet wall prepared byremoving loose and deposited material with brush and water,laying glass fibre mesh of 10 x10 specification of approved makeover tacky surface of first coat of polymer followed by second coatin transverse direction, sprinkling coarse sand over it, followed byprotective mechanical cover of 40 to 75 mm thick cement concreteof 1:2:3 proportion using coarse aggregate including usingmembranes

1000 SQM

of 10 MSA and water proofing compound of approved make andpolypropylene fibres @ 125 gm per bag of cement within itconforming to IS in pannels of 3m/4m oras per site condition &filling the the joints with poly sulphide sealant (0.08 kg. per sq.m.)after curing, including providing holler with drip mould at thejuction and finishing the concrete surface with neat cement slurryincluding curing as directed and ponding the surface as directedetc. complete. covering 10 years guarantee against leakproofnesson Court Fee Stamp Paper of Rs. 100. (Note for stanting lengthupto 5.0 m) (Excluding grouting and Removing existing treatmentto be paid separetely as required) Spec. No. As directed byEngineer-in-charge and as per manufacturers specifications.

Page 9



33 Providing water proof bedding for flooring of Bath and WC 25mm thick in C.M. 1:3 including using approved water proofingcompound in specified proportion as per manufacturersspecifications for per bag of cement including leveling, curing andcovering 10 years guarantee on court fee stamp paper of Rs.500/-including ponding test etc. complete. [Spec.No. : As directed byEngineer in charge]

51 SQM

34 Providing internal cement plaster 6 mm thick in a single coat incement mortar 1:3 without neeru finish to concrete surface in allpositions including scaffolding and curing etc. complete. Asdirected by Engineer in charge.

1050 SQM

35 Providing internal cement plaster 12mm thick in single coat incement mortar 1:4 without neeru finish to concrete or bricksurfaces, in all positions including scaffolding and curing etc.complete. [Spec.No.: Bd.L.2/Page No.368]

2103 SQM

36 Providing sand faced plaster externally in cement mortar usingapproved screened sand, in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound at 1kg per cement bag curing the same for not less than 2 days andkeeping the surface of the base coat rough to receive the sandfaced treatment 6 to 8 mm thick in cement mortar 1:4 finishing thesurface by taking out grains and curing for fourteen daysscaffolding etc.complete. [Spec.No.: Bd.L.7/Page NO.369]

1185 SQM

37 Providing and fixing chicken mesh of 22 gauge, with about 30cm. width at the junction of R.C.C members and brick work, ofapproved quality including fixing mesh in position by necessarydrilling in concrete or/B.B.masonry and or tying by binding wireetc. complete. [Spec.No. : As directed by Engineer-in-charge]

330 RMT

Page 10



38 Providing and laying ceramic tiles of having size 30 cm x 30 cm confirming to I.S.15622/ 2006 (group D II-A) and 7 to 8 mm thick for flooring in required posi t ion laid on a bed of 1:4 cement mor tar including cement float , fi lling joint wi th whi te/ colour cement slurry cleaning cur ing etc. complete. Spec. No. :Bd.M.12 Page No. 385.

51 SQM

39 Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to cor responding I.S. for dado and skirting in required position wi th readymade adhesive mortar of approved quality on plaster of 1:2 cement mor tar including joint fi lling with white/ colour cement slurry cleaning cur ing etc. complete. Spec. No. :Bd.M.13 Page No. 386.

92 SQM

40 Providing and laying cement concrete flooring 50 mm thick withM15 cement concrete laid to proper level and slope in alternatebays including compaction filling joints, marking lines to give theappearance of tiles of 30cm x 30cm or other size laid diagonally/square etc finishing smooth (with extra cement) in any colour asdirected and curing etc. complete. With Natural Sand [Spec.No.:Bd.M.7 Page No. 383]

190 SQM

41 Providing and laying machine cut machine Polished Kota stoneflooring 25mm to 30mm thick and required width inplain/diamond pattern on bed of 1:6 C. M. including cement float,filling joints with neat cement slurry, curing, polishing and cleaningetc. complete. Bd.M.3 Page No. 380

1066 SQM

Page 11



42 Providing Mirror polishing to Kota Stone including using all

necessary stones and equipments cleaning, washing etc.

complete. For Skirting As directed by Engineer in charge.

107 RMT

43 Providing and laying machine cut machine polished machine cutKota stone slabs 20 to 25 mm thick for treads and risers of stepsand staircases, with rounded nosing for the treads on a bed of 1:4cement mortar including cement float, filling joints with neatcement slurry, curing, polishing and cleaning etc.complete

70 SQM

44 Providing and applying putty to new plastered surfaces in twocoats to receive approved paint in all positions including all materials,labour scaffolding and curing etc. complete.

3153 SQM

45 Providing and applying priming coat on concrete/ masonary/Asbestos Cement plastered surfaces including scaffolding ifnecessary, preparing the surface by thoroughly cleaning oil,grease, dirt and other foreign matter and sand papering asrequired etc. complete. [Spec.No.: Bd.P.6/Page No.414]

4337 SQM

46 Providing and applying plastic emulsion paint of approved quality,colour and shade to old & new surfaces in two coats includingscaffolding, preparing the surface. (excluding the primer coat)etc.complete.

3153 SQM

Page 12



47 Providing and fixing M40 grade thick vibrated pull cast or similartype concrete frame with chamfer conforming to I.S. 65241983having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c andfixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mmlong including primer and oil painting etc, complete) frame size 60mm x 100 mm

160 RMT

48 Providing and laying telephone black / Amba White /Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to20 mm thick for door frame/ dado/ window boxing etc. On C.M.1:6 including filling joints with polymer base filler nosing the sharpedges wherever necessary, curing, etc. complete.[Spec.No.: Asdirected by Engineer- in-charge]

24 RMT

49 Providing and fixing collapsible steel gate in one / two leaveswith hot rolled vertical channels of 18 x 9 x 3 mm minimum size,crossings of M.S. flats of size 18 x 5 mm T or E section for runnerof minimum 40 x 6 mm size for flange, M.S. flat for top runner ofminimum size 40 x 12 mm with roller wheels confirming to gradeF.G. 150 fitted with snap headed rivets of minimum size 6 mmmax. spacing of vertical channels be 100 mm enclosed gateposition and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangementand one coat of red lead primer & oil painting etc. complete. (I.S.10521-1983). [Spec.No. : Bd. T. 57/Page No. 511.]

4 SQM

Page 13



50 Providing and fixing solid core flush door shutter in single leaf32 mm thick decorative type of exterior grade as per detaileddrawings approved face veneers 3 mm thick on both faces or asdirected, all necessary beads, mouldings and lipping, wrought ironhold fasts, chromium plated fixtures and fastenings, with brassmortise lock, chromium plated handles on both sides, andfinishing with French Polish etc. complete. [Spec.No.:Bd.T.34/Page No.499]

75 SQM

51 Providing and fixing fiber glass reinforced polyster door shutter 30

mm thick as per IS 14856 (2000) (Reaffirmed 2006) without

ventilator including chromium plated fixtures and fastening with

chromium plated handles onboth sides, etc complete.

10 SQM

52 Providing and fixing in position (as per 1868 / 1982) Aluminiumsliding window of three tracks with rectangular pipe 95 x 38.10x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottomtrack section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Topand side track section 92 x 31.75 x 1.30 mm at weight 1.070kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25mm at weight 0.469 kg/Rmt. Inter locking section 40 x 18 x 1.10mm at weight 0.417 kg/Rmt. and handle and top section 40 x 18 x1.25 mm at weight o.469 kg/Rmt. As per detailed drawings and asdirected by Engineer-incharge with all necessary Aluminiumsections fixtures and fastenings such as roller bearing in nyloncasting and self locking catch fitted in vertical section of shutterincluding 5 mm thick plain glass and aluminium mosquito netshutter with stainless steel jail with all required screws and nutsetc, complete. With powder coating with box

92 SQM

Page 14



53 Providing and fixing in position powder coated aluminiumlouvered windows / ventilator of various sizes with powdercoating as per detailed drawing and specifications includingaluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thicksheet glass louvers, of approved quality etc. complete. [Spec.No. :As directed by Engineer-in-charge]

17 SQM

54 Providing and fixing mild steel grill work for windows, ventilators

etc. 20 kg/sqm as per drawing including fixtures, necessarywelding & painting with one coats of anticorrosive paint & twocoats of oil painting complete. [Spec.No. : Bd.U. 1 Page No. 537]

94 SQM

55 Providing and applying two coats of synthet ic enamel paint ofapproved colour to new / old st ructural steel work and wood workin bui ldings, including scaffolding i f necessary, cleaning andpreparing the sur face (excluding pr imer coat ) etc. complete.Spec.No. :Bd.O.5 Page No. 405

94 SQM

56 Providing and fixing 900mm high S.S.304 Grade Stainless steelrailing with 40mm diameter and 1.5mm thick at top,40mmdiameter and 1.5mm thick vertical supports spaced at 3.3m centerto center and two pipes of 12mm diameter fixed horizontallyincluding fabricating ,fixtures, errecting, necessary welding,grinding, finishing, buffing to stainless steel pipe etc. complete.

15 SQM

Page 15



57 Providing and fixing heavy duty inter locking concrete Rubbermould glossy paving blocks of 80 mm thickness of having astrength of 400 kg/Sq.cm. of approved quality and shape on a bedof crushed sand of 25 to 30 mm thick including skirting joints andcleaning etc. complete. (using 100% crushed sand) [Spec.No.:As directed by Engineer- in-charge]

570 SQM

58 Providing and fixing in position structural glazing consisting of main frame of powder coated jindal or equivalent make alluminium curain wall section 48 x 64 mm &sub frame of 25 x 25 x 2 mm powder coated alluminium SHS by using structural silicon of Dow Corring 995 weather silicon coirining 785, Spacer tape 6 mm x 6 mm excluding glass inclusive of labour etc.

75 SQM

59 Providing and fixing 90 cm. x 60 cm. Granite plate engraving10cm. Height letter, figures including painting the lefters/figureswith approved colour and shade complete. [Spec.No.: Bd.W.7Page No.586]

1 NO

60 Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC

pipe with necessary fittings, remaking good the demolished

portion etc. complete. [Spec.No. : As directed by Engr-in-charge]

15 RMT




15 RMT

Page 16






15 RMT




15 RMT




15 RMT




15 RMT

66 Providing and fixing 15 mm dia. screw down bib/ stop tap ofbrass including necessary socket union nut complete. [Spec.No. :Bd.V. 8 Page No. 554]

3 NO

67 Providing and fixing screw down for 20 mm dia. wheeled stop tapof brass including necessary sockets/union nut complete.[Spec.No. : Bd.V. 9 Page No. 555]

3 NO


3 NO

Page 17




3 NO

70 Providing and fixing white glazed earthenware Wash HandBasin of 55cm. x 40 cm. size including cold water pillar tap/coldand hot water pillar tap brackets, rubber plugs and brass chain,stop tap and ecessary pipe connections including P.V.C.wastepipe and trap up to the outside face of the wall. Makinggood the damaged surface, testing etc. complete [Spec.No.:Bd.V.30 Page No. 565]

6 NO

71 Providing and fixing 15 cm rigid PVC Nahani trap including PVCgrating ,bend,connectingpiece of UPVC pipe up to the outsideface of wall ,making the good damaged surface and testing etc.complete ( Prior approval of sample and brand by Ex. Engr. isnecessary before use)

6 NO

72 Providing and fixing 15cm x 10cm salt glazed stoneware gullytrap in cement concrete 1:4:8 outside the building including castiron grating in the sink, connecting glazed stoneware pipe, brickmasonry chamber with cast iron lid and cast iron grating for thegully trap. [Spec.No.: Bd.V.38/Page No.572]

4 NO

73 Providing, laying & fixing P.V.C. pipe of 40mm dia. with fittings

such as bends, tees, reducers, clamps, etc. including necessaryexcavation, trench filling etc. complete. [Spec.No. : Bd.V. 60 Asdirected by Engineerincharge.]

10 NO

Page 18



74 Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil

vent/waste pipe and with necessary fixtures and fitting such asbends, tees, single junctions, slotted vent, clamps etc. complete[Spec.No. : As directed by Engineer in charge.]

40 RMT

75 Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil

vent/waste pipe and with necessary fixtures and fitting such asbends, tees, single junctions, slotted vent, clamps etc. complete[Spec.No. : As directed by Engineer in charge.]

40 RMT

76 Providing , laying & fixing ,jointing Supreme Eco- drain 200 mmSN 4 Nu- Drain Upvc pipes or of equivalent make, manufactureas per EN 13476 or equivalent as per I.S.15328 with fittings sucha bends, tees, coupler, etc, jointing with rubber lubricant includingnecessary excavation, trench refilling with selective excavatedmaterialetc.complete. [Spec.No. : As directed by Engineer incharge.]

40 RMT

77 Providing and laying concrete pipes of I.S.NP. class of 300mmdiameter in proper line, level and slope including necessarycollars, excavation, laying, fixing with collars in cement mortar 1:1and refilling the trench complete. [Spec.No. : Bd.V. 36 Page No.571]

20 RMT

78 Providing & constructing Brick Masonry Inspection Chamber60cm x 45cm x 90cm including 1:4:8 cement concrete foundation1:2:4 cement concrete channels half round G.S.W. pipes, BrickMasonry, plastering from inside and airtight C. I. lid 65 kg withframe fixed in cement concrete etc. complete. [Spec.No.:Bd.V.43/Page No.574]

2 NO

Page 19



79 Providing & constructing Brick Masonry Inspection Chamber90cm x 45cm x 90cm including 1:4:8 cement concrete foundation1:2:4 cement concrete channels half round G.S.W.pipes, BrickMasonry, plastering from inside and C.I. lid cover 75 kg with framefixed in cement concrete. [Spec.No.: Bd.V.43/Page No.574]

4 NO

80 Providing and constructing Brick Masonry inspection Chamber90cm x 45cm including 1:4:8 C.C foundation, 1:2:4C.C.channels/half round glazed stoneware pipe channel, saltglazed stoneware intercepting trap with rodding pipe set in 1:4:8cement concrete block, brick masonry plastering inside andOutside, with C.I. lead cover with frame fixed in cement concrete.[Spec.No.: Bd.V.44/Page No.575]

1 NO

81 Providing and fixing Orissa type white glazed earthenware 575mm water closet pan including S trap with earthenware foot rests,cast iron soil and vent pipe upto outside face of the wall 1:2:4 brickbat lime concrete bedding without flushing tank and itsaccessories etc. complete. [Spec.No. : As directed by Engr-in-charge]

2 NO

Page 20



82 Providing and fixing European type white glazed earthenwarewater closet pan with UPVC seat and lid with chromium platedbrass hinges and rubber buffers including UPVC and vent pipe upto the outside face of wall 10 litre enameled low level flushingcistern with fittings pipe stop tap brackets for fixing cistern 32 mmdia. UPVC flush pipe with fittings and clamps ,20 mm dia.UPVCoverflow pipe ,mosquito proof couplings G.I. chain and pulley,withwater Jet and fitting including cutting and making good to the wallsand floors testing etc. complete.(prior approval of sample andbrand by Ex.Engineer is necessary before use) [Spec.No. : Asdirected by Engr-in-charge]

3 NO

83 Providing and fixing H.D.P container Syntex or alike one piecemoulded water tank made out of low density polythyler and builtcorrugation including of delivery up to destination hoisting andfixing of accessories such as inlet, outlet overflow of all tankscapacity above 1000 to 20,000 litres

12000 LIT

84 Providing and Fixing 110 mm diameter PVC Rain Water pipe with necessary fittings such as bends, tees, single junctions,slotted vent, clamps etc complete. [Spec.No.: As directed byEngineer- in-charge]

28 RMT

85 Providing and fixing 450mm x 550mm size superior type

Belgium mirror with 16mm dia. nickel plated towel rod etc.

complete. [Spec.No.: As directed by Engineer- in-charge.]

6 NO

86 Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete. [Spec.No.: As directed by Engineer- in-charge.]

8 NO

Page 21



87 Transportation of material obtained from debris of various sorts

including necessary excavation/loosing including loading,

unloading and conveying and disposing as directed. For 5 Km

850 SQM

88 RWH - Recharge Pit Providing and constructing recharge pit of2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5" dia x 25mdeep borewell at the floor of recharge pit including installation ofcombination of solid/perforated PVC casing pipe wrapped aroundwith netlon mesh including 300mm thick sidefilling around outsideof RCC rings (annular space) with 40mm size boulders includingfilling of recharge pit up to 0.5m depth with 25-75mm cleanwashed gravels from bottom up followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed riverfine aggregate (natural sand/crushed sand VSI grade finelywashed etc.) including netlon mesh between each gravel/fineaggregate (natural sand/crushed sand VSI grade finely washedetc.) media layer including covering with RCC slab, manholeframe & cover, PVC rungs, PVC end-caps, fittings etc. includingarrangement for inlet & outlet pipe excavation & backfilling asshown in the drawing.The rate shall be inclusive of all labour,material, wastage, scaffolding, transportation, taxes, including allleads, lifts at all levels. All material should be of approved make.All works complete as per the drawing, technical specification anddirection of the Engineer in charge

1 NO

Page 22



89 Cleaning of site including cutting of bushes, trees of all girthjs,removing of roots oif soil, Spreading of soil, Surface dressing,Dismantling of existing structure if any including stacking at AEStore , an transportation of excess excavated soil from site to anyother place on thje VNIT Campus and including thje temporarilyG.I/AC Sheet partition for the protection during construction withall framework as directed [Spec.No.: As directed by Engineer- in-charge.]

50 Day

C.C.Road 90 Excavation for roadway in earth, soil of all sorts, sand,

gravel or soft murum including dressing section to therequired grade, camber and side slopes and conveying theexcavated materials with all lifts upto a lead of 50m. andspreading for embankment or stacking as directed.

18 Cum

91 Construction of granular sub-base by providing closegraded Material, mixing in a mechanical mix plant atOMC, carriage of mixed Material to work site, spreading inuniform layers with motor grader / Paver on preparedsurface and compacting with vibratory roller to achieve thedesired density, complete as per clause 401 -- Plant MixMethod and Grading - II Material

9 Cum

Page 23



92 Providing, laying, spreading and compacting stoneaggregates of specific sizes to water bound macadamspecification including spreading in uniform thickness,hand packing to proper grade and camber, applying andbrooming requisite type of screening/ binding Materials tofill up the interstices of coarse aggregate, watering andcompacting with vibratory roller to the required density. ByMechanical Means -Grading I (Using Screening Type B(11.2 mm) Aggregate)

5 Cum

93 Providing, laying, spreading and compacting stoneaggregates of specific sizes to water bound macadamspecification including spreading in uniform thickness,hand packing to proper grade and camber, applying andbrooming requisite type of screening/ binding Materials tofill up the interstices of coarse aggregate, watering andcompacting with vibratory roller to the required density. ByMechanical Means - Grading II (Using Screening Type B(11.2 mm) Aggregate)

9 Cum

Page 24



94 Construction of dry lean cement concrete Sub- baseover a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushedsand) conforming to IS: 383, the size of coarse aggregatenot exceeding 25 mm, , cement content not to be less than150 kg/ cum, optimum moisture content to be determinedduring trial length construction, concrete strength not to beless than 10 Mpa at 7 days, mixed in a batching plant/Weigh batch mixer, transported to site with all leads andlifts, laid with a paver with electronic sensor /by suitablemeans as approved by Engineer-in-charge , compactingwith vibratory roller, finishing, curing and includingpreparation of subgrade surface if required etc. complete.

6 Cum

95 Providing and laying 125 micron Low DensityPolyethylene (LDPE) sheet confirming to IS 3395 : 1997below concrete pavement including all materials andlabour complete.

60 Sqm

Page 25



96 Providing and laying in-situ M30 Grade unreinforcedplain cement concrete pavement over a prepared subbase with 43 grade cement , coarse and fine aggregateconforming to IS 383, using fine & coarse aggregatescombined gradation as per Table 600-3 of MORTHSpecification 2013, mixed in a batching and mixing plant/non tilting mixer and Weigh batcher as per approved mixdesign, admixtures, transporting to site, spreading, layingcompacting and finished in a continuous operation,finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providingcement vata in cement Mortar 1:8 @0.6m X 0.6m centre tocentre, admeasuring 80 mm at bottom and 40 mm at topwith depth of 75mm and maintaining the same throughoutcuring period by any other method approved by Engineer-in-charge ( initial lead of 5.00 Km for raw materials upto plant site )Spec. No. M.O.R.T.& H 2013. Cl-602P.N.263

8 Cum

97 Cutting transverse contraction joints 3 to 4 mm wideand depth 60mm. .in concrete slab using concrete cuttingmachine with diamond studded saw within 48 hours ofcasting of bay / slab etc. complete including subsequentwidening of the groove 8 to 10 mm. wide at top havingdepth of 15 mm. as directed by Engineer incharge.

16 Rmt

Page 26



98 Providing to contraction joints polysuphide sealent(Pouring grade) confirming to BS : 5212 - 1989 intosawed groove widened at top for sealent reservoir ofspecified size and shape as per detailed drawing includingfixing Polyethylene foam backer rod of required diameter(appraox. 25% larger than the initial 3 mm.to 4 mm. joint)overlaid with bond breaking tape as per detailed drawing.Item includes cleaning the joints with water jet / aircompressor and allowing joint to become thoroughly drybefore sealent is applied and applying primer. (A)Contraction and longitudinal joints (15 mm. deep x 8mm.wide)

16 Rmt

99 Providing selected hard murum filling including laying inlayers of 15 to 20cmwith watering and compacting etc.complete.

3 Cum

100 Providing and fixing heavy duty inter locking concreteRubber mould glossy paving blocks of 80 mm thicknessof having a strength of 400 kg/Sq.cm. of approved qualityand shape on a bed of crushed sand of 25 to 30 mm thickincluding skirting joints and cleaning etc. complete. (using100% crushed sand)

6 Sqm

Page 27



101 Providing and fixing in position TMT -FE - 500 barreinforcement of various diameters for R.C.C. pile caps,footings, foundations, slabs, beams and columns,canopies, staircases, newels, chajjas, lintels, pardies,coping, fins, arches etc. as per detailed design anddrawings and schedules including cutting, bending,hooking the bars, binding with wires or tack welding andsupporting as required completed.

0.70 MT

102 Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc.including necessary excavation, trench filling etc.complete. Including removing existing pipe line ifnecessary and conveying and stacking the same in PWDchowky or as directed etc.complete.

12 Rmt

Page 28



103 Supplying and Fixing of Molded Shank RaisedPavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with microprismatic lens capable of providing total internal reflectionof the light entering the lens face and shall support a loadof 16000 kg tested in accordance to ASTM D 4280 Type Hand complying to Specifications of Category A of MORTHCircular No RW/NH/33023/10-97 DO III Dt 11.06. 1997.The height, width and length shall not exceed 50 mm, 100mm and 102 +/- 2 mm and with minimum reflective area of13 Sqcm on each side and the slope to the base shall be35 +/- 5 degree. The strength of detachment of theintegrated cylindrical shanks, (of diameter not less than 19+/- 2 mm and height not less than 30+/- 2 mm) from thebody is to be a minimum value of 500 Kg. Fixing will be bydrilling holes on the road for the shanks to go inside,without nails and using epoxy resin based adhesive as permanufacturer's recommendation and complete as directedby the engineer.The contractor shall submit a two yearwarranty for satisfactory field performance includingstipulated retroreflectance of the reflecting panel, to theEngineer.

4 Nos

Page 29



104 Providing and fixing board displaying information,such as 'Name of work, Tender cost, Name ofContractor, Work completion and liability period etc',having rectangular shape of 1.20m x 0.90m size made out18 gauge (1.25mm) thick mild steel sheet painted with onecoat of Zinc chromate stoving primer and two coats ofenamel paint on front side and grey stove enamel on backside and border / messages / symbols etc. with approvedcolour shade paint complete, on M.S.angle of size 35 x 35x 3 mm frame with properly cross braced M.S. angles ofsize 35mmx35mmx3mm duly painted including Two M.S.angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 mlong painted with alternate black and white bands of 25 cmwidth including all fixtures etc.and fixing the boards in 1:4:8concrete block of size 60 cm x 60 cm x 75 cm including,excavation, refilling, transportation, and labour etccomplete. Spec. No. As directed by Engineer in Charge

1 Nos

R.C.C. COVER DRAIN105 Removing rich mix cement concrete including stacking

the spoils as directed with all leads, lifts etc, complete 16 Cum

106 Excavation for catch / side water gutter in all sorts ofsoils to the specified section including stacking theexcavated stuff in a regular bund and disposing ofunsuitable or excess stuff as directed

78 Cum

107Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit,ramming, watering etc. complete.

16 Cum

Page 30



108

Providing and laying in situ / ready mix cement concreteof M-15 proportion with trap/ granite/ quartzite/ gneissmetal in foundation including necessary form work,compacting and curing etc. complete. (with reversibledrum type mixer with SCADA with fine agreegates ofrequired specifications (Natural sand / VSI sand finelywashed etc )

11 Cum

109

Providing and laying Cast in situ/Ready Mix cementconcrete in M25 of trap/ granite/quartzite/gneiss metal forbed blocks, foundation blocks and such other itemsincluding bailing out water, plywood/steel formwork, laying/pumping, compacting, roughening them if special finish isto be provided, finishing uneven and honeycombedsurface and curing etc. complete. The Cement Mortar 1:3plaster is considered for rendering uneven andhoneycombed surface only. Newly laid concrete shall becovered by gunny bag, plastic, tarpaulin etc. Woodencentering will not be allowed.), with fully automatic microprocessor based PLC with SCADA enabled reversibleDrum Type mixer/ concrete Batch mix plant (Pan mixer)etc. complete. With natural sand/V.S.I. quality ArtificialSand

9 Cum

110

Providing and laying in situ / ready mix controlled gradeof M25 of trap /granite /quartzite /gneiss metal for RCCworks in cut off walls / curtain walls including necessaryscaffolding, centering, compacting by vibrator, finishingand curing etc. complete. (with fully automatic microprocessor based PLC with SCADA enabled with reversibledrum type mixer/ concrete batch mix plant (pan mixer) withnatural /artifical sand, excluding reinforcement)

13 Cum

Page 31



111

Providing and laying in situ / ready mix M25 controlledcement concrete of trap/ granite/ quartzite/ gneiss metalfor RCC work in solid/ deck slab etc. including ramming,vibrating, curing, formwork, centering and finishing incement plaster excluding reinforcement etc. complete.(height up to 4 meter with fully automatic micro processorbased PLC with SCADA enabled reversible drum typemixer/ concrete batch mix plant (pan mixer) with natural/artifical sand)

10 Cum

112

Providing and fixing in position TMT -FE - 500 barreinforcement of various diameters for R.C.C. pile caps,footings, foundations, slabs, beams and columns,canopies, staircases, newels, chajjas, lintels, pardies,coping, fins, arches etc. as per detailed design anddrawings and schedules including cutting, bending,hooking the bars, binding with wires or tack welding andsupporting as required completed.

1.65 MT

113

Providing, laying and fixing P.V.C. pipe of 50mm dia. withfittings such as bends, tees, reducers, clamps, etc.including necessary excavation, trench filling etc.complete. Including removing existing pipe line ifnecessary and conveying and stacking the same in PWDchowky or as directed etc. complete.

14 Rmt

Page 32



114

Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc.including necessary excavation, trench filling etc.complete. Including removing existing pipe line ifnecessary and conveying and stacking the same in PWDchowky or as directed etc.complete.

4 Rmt

Total Amount of Part - A Civil Work

Contractor DirectorVNIT, Nagpur.

Page 33

(in figure) (in words)1

Asbestos cement sheet obtained from Mett work shop shed roof dismantle

500 SqM

2 Structural steel like M.S Angle, channels, cleat, plates, Trusses etc. obtained from removing trusses of w/shop shed

25 M.T.

3M.S. windows / Door

40 SqM

4Rolling shutter 5 SqM

5Brick masonary/RCC 100 CuM

Total Amount of Part - B Credit Work (-)


Rate in Rs.Amount

Part B- Credit Work

Item no. Items of work Estimated Quantity Unit

Page 1


1

PREPARING LAWN (20cms. Depth) :- Excavating theground to a rquired depth of 20 cm removing & conveyingunwanted stuff to arequired distance as directed. Fillingfersh garden soil/silt & manure in excavated area 3:1proportion to a height of 20 cm. Mixing garden soil &manure throught, well, levelling, watering on previous night.Planting required varicty of lawn grass as directed &maintaingn till well establish by watering, weeding, clipingrolling, etc. complete.

275 CuM

2

PREPARING FLOWER BED :- Excavating the ground torquired depth of 30 cm. Removing & conveying unwantedstuff to arequired distance as directed. Filling fresh gardensoil & manure in excavated area in 3:1 proportion to arequired height of 30 cm. Mixing garden soil & manurethroughly well, levelling, watering on pervious night.Planating seedlings of required annuals 25cms, apartMaintaing till well estalished by watering, weeding, Stirringreplacing of casualties etc. complete.

5 CuM

3

PLANTING CLIPPED HEDGE:- Excavating the ground to arquired depth of 30 cm, removing and conveying unwantedstuff, rubbish to a the required distance as directed. Fillingfresh garden soil and manure in excavated area in 3:1proportion to a height to 30 cms. Mixing garden soild andmanure throughly well, levelling, watering previous night.Planting hedge plant of required species in two rows.distance between two rows & between two plants will be25cms. Maintaining till well established by wateringweeding, stirring the soil and clipping if necesary etc.complete.

50 Rmt

Rate in Rs.Amount

Part C- Horticulture


Page 1

4

Planting small and medium size ornamental / Floweringplant : Digging pit with size 0.6mx0.6mx0.6m, removingand conveying unwanted stuff to a required distance asdirected. Providing filling the pit with fresh garden soil andfarmyard manure upto a height of 0.6m in 3:1 proportion,mixing soil and manure thoroughly well,levelling,wateringon previous night. Planting one to two year old healthy plantsaplings as per specification. Maintaining till wellestablished by watering strring of soil replacing of casulitiesetc.complete

20 Nos

Total Amount of Part - C Horticulture Work


Page 2


1

Point wiring for light/fan/bell concealed type in min 20 mmPVC conduit with 1.5 sq.mm. FR grade copper wires withmoduler type switch and required accessaries as perspecification No: WG-PW/CW

175 Point

2

Wiring for plug on board with Switch socket concealed

type and copper wiring, earthing and with modular

accessories as per specification No: WG-PW/CW

55 Point

3

Supplying and erecting flush type shockproof plug socket

6A.& 16A (6 pin) with 16A switch combined with indicator

lamp and fuse with gang box on wooden board.

25 Each

4Supplying and erecting rigid PVC conduit 20 mm dia.with PVC accessories on wall / ceiling as per specificationNo: WG-MA/CON, para no. 1.1.1

2700 Mtr

5Supplying and erecting rigid PVC conduit 25 mm dia.with PVC accessories on wall /ceiling as per specificationNo: WG-MA/CON, para no. 1.1.1

400 Mtr

6

Supplying & erecting original 1.25 mm CRCA sheet metalenclosures with 30A, 3 pin plug & earth socket and 30 A 3pin plug top with 30A triple pole MCB complete erected onangleiron/ GI frame

34 Each

7

Supplying and erecting triple pole and neutral distributionboard (TPNDB) surface/ flush mounted SP / TP of 24 wayson iron / GI frame (vertical busbar type) as perspecification no. SWSWR/ MCBDB

2 Each

8

Supplying and erecting single pole and neutral distributionboard (SPNDB) with door surface /flush mounted with 2ways for incoming and 10 ways for outgoing SP MCB’s oniron/ GI frameas per specification no. SW-SWR/MCBDB

6 Each

Rate in Rs.Amount

Part D- Electrical Work


Page 1

9Supplying, erecting & marking DPMCB 6 A to 32 A B-series (for lighting) in provided distribution board as perspecification no. SWSWR/ MCB

12 Each

10Supplying, erecting & marking SPMCB 6A to 32A, C-series(for motor/power) in provided distribution board as perspecification no. SW-SWR/MCB

40 Each

11Supplying, erecting & marking FPMCB 40A to 63A inprovided distribution board as per specification no. SW-SWR/MCB

6 Each

12

Providing & erecting 3 Pole MCCB upto 100A, 415V, withshort circuit rating 25 kA (Ics=100% of Icu ),adjustablethermal (overload) setting and fixed magnetic setting withprovided leads, provision for installation of shunt/ UV/ tripalarm contact and MCCB should have phase barriers bothsides, in provided enclosureon iron /GI frame as per specification no. SW-SWR/MCCB

2 Each

13

Providing & erecting 3 Pole MCCB of 200A,415V capacitywith short circuit rating 25 kA Ics=100% of Icu) adjustablethermal (overload) setting and fixed magnetic setting withprovided leads, provision for installation of shunt/ UV/ tripalarm contact and MCCB should have phase barriers bothsides, in provided enclosure on iron /GI frame as perspecification no. SW-SWR/MCCB

1 Each

14Supplying and erecting four pole metal clad ON LOADchange over switch 415V, 200A erected on angle iron /GIframe approved make complete.

1 Each

15

Supplying & erecting mains 2x1.5 sq.mm. and earth wire1.5 sq.mm FR PVC copper wire, ISI mark HMS PVCconduit min. 20mm dia, as per specification No: WG-MA/PC.

2000 Mtr

16Supplying and erecting bus bar chamber triple pole withneutral with four aluminium bars, 500V 200A complete asper specification no. CP-BB

1 Each

Page 2

17

Supplying & erecting mains with 2x2.5 sq.mm.and earthwire 1.5 sq.mm FR PVC copper wire, in rigid PVC conduitmin.20mm dia, as per specification No: WG-MA/PC, parano. 1.4.1

1800 Mtr

18

Supplying & erecting mains with 2x4 sq.mm.and earth wire2.5 sq.mm FR PVC copper wire in rigid PVC conduitmin.20mm dia,as per specification No: WG-MA/PC, parano. 1.4.1

1000 Mtr

19

Supplying & erecting mains with 4x4 sq.mm.and earth wire2.5 sq.mm FRLS PVC copper wire, in rigid PVC conduit25mm dia, as per specification No: WG-MA/PC, para no.1.4.1

600 Mtr

20

Supplying & erecting mains with 4x10 sq.mm. and earth

wire 6 sq.mm FR PVC copper wire, in HMS PVC conduit

min. 32mm dia, as per specification No: WG-MA/PC.

400 Mtr

21

Supplying and erecting five star rated energy savingCeiling fan 230 V A.C. 50 cycles 1200 mm completeerected in position as perspecification no. FG-FN/CF

34 Each

22

Supplying and erecting modular type electronic dimmer1000W two module ISI mark approved make duly erectedon provided plate and box with wiring connectionscomplete.

34 Each

23Supplying and erecting exhaust fan heavy duty 440 V A.C.50 cycles 900 RPM 375/380 mm complete erected inposition as per specification no. FG-FN/EXF

2 Each

24

Supplying, erecting & terminating XLPE armoured cable3½ core 35 sq. mm. aluminium conductor with continuous5.48 sq. mm. (12 SWG) G.I. earth wire complete erectedwith glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as perspecification no. CB-LT/AL

70 Mtr

Page 3

25

Supplying, erecting & terminating PVC armoured cable 3½core 70 sq mm aluminium conductor with continuous8.35 sq mm (10 SWG) G.I. earth wire complete erectedwith glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. CB-LT/AL

100 Mtr

26

Supplying, erecting & terminating XLPE armoured cable 3core 2.5 sq. mm. aluminium conductor with continuous5.48 sq. mm.(12 SWG) G.I. earth wire complete erected with glands &lugs, on wall/ trusses/pole or laid in provided trench/ pipeas perspecification no. CB-LT/AL

600 Mtr

27

Providing earthing with copper earth plate size 30 x 30 x0.315 cmcomplete with all materials, testing & recording the resultsas perspecification no. EA-EP

10 Each

28Providing pipe type earthing with 40mm. dia. G.l. pipe or20 mm dia. G.l. Rod complete with all materials as perspecification no. EAEP

6 Each

29

Supplying and erecting LED square / circular 16 to 20Wdown lighter having pressure die-cast aluminium housing,opal translucent cover, mounting arrangement with boardfor surfacetype or spring loaded mounting clips for flush typecomplete.

98 Each

30Supplying & erecting LED 20W tube light fitting (4 feet)with aluminium housing, heat sink, integrated HF electronicdriver complete.

12 Each

31

Supplying and erecting LED street light fitting suitable for20 to 25W, with PF > 0.95 class IP 65 and above housingof pressure die cast aluminium alloy and heat sinkextruded aluminium complete as per specification No FG-ODF/FLS-2.

12 Each

Page 4

32Supplying & installing UTP networking cat-6+ cablesuitable for LAN / WAN Computer net-working as perspecification no. WG-COC/NC complete

3000 Mtr

33

Supplying and erecting ISI mark modular type computer

jack RJ 45 with safety shutter, duly erected on provided

plate and box with wiring connections complete.

30 Each

34 Supplying, installing, testing & commissioning digital(hybrid) type EPABX of 6 x 16 extensions complete. 1 Each

35 Supply and erecting hooters with CRCA enclosurecomplete as per specification No. FF-FAAS/HTR 4 Each

36Supplying, installing, testing and commissioning opticaltype smoke detector complete on box as per specificationno. FFFAS/ SD

38 Each

37 Supplying, erecting and testing remote responseindicators as per specification No. FF-FAAS/RRI 38 Each

38Supplying and erecting XLPE armoured cable 4 core1.5 sq.mm. copper complete erected on wall/ ceiling asper specification No. CB-LT/CU

550 Mtr

39

Supplying, erecting, testing and commissioning the 2Zones Microprocessor based conventional Fire AlarmControl Panel (FACP) with standard accessories completeas per specification No. FF-FAAS/FACP

3 Each

40

Supplying and erecting ultra violet storage type waterpurifier ( RO+UV+UF) with softener for safe drinking waterconsisting of UV germicidal tube of 8W capacity chokemade of copper wire and two indicator lamps with output ofpurified water 7 to 8 litre/min with activated carbon filterand softener operating on 230 V single phaseA.C. supply.y.

1 Each

41

Supplying, erecting, testing and commissioning selfcontained water cooler 230/250 Volts 50 cycles nominalcooling capacity of 150 liters/hr and storage capacity 150liters with partially stainless steel body complete.specification no. AP-WCR/WC

1 Each

Page 5

42

Supplying and erecting iron, sheet metal work consisting ofCRCA sheets, various sections of iron, plates, chequeredplates rods, bars, MS pipes, etc. for panel board or anyother purpose with bending, cutting, drilling and weldingcomplete erected at the position with necessary materialsduly painted with one coat of red oxide and two coats ofenamel paint to match the switchgears or asper directions by the authority.

100 Kg

43

Supplying, erecting & terminating XLPE armoured cable3½ core 120 sq. mm. aluminium conductor with continuous12.97 sq. mm. (8 SWG) G.I. earth wire complete erectedwith glands & lugs, on wall/ trusses/ pole or laid in providedtrench/ pipe as per specification no. CB-LT/AL

150 Mtr

44

Providing & erecting 4 Pole MCCB upto 100A, 415V, withshort circuit rating 25 kA (Ics=100% of Icu ),adjustablethermal(overload) setting and fixed magnetic setting with providedleads, provision for installation of shunt/ UV/ trip alarmcontact and MCCB should have phase barriers both sides,in provided enclosure on iron /GI frame as perspecification no. SW SWR/ MCCB

1 Nos

45Supplying and erecting enclosur box for 100/200/250AMCCBs with neccesary angle iron work in an approvedmanner.

1 Nos

46Supplying and erecting terminal spreaders for use onMCCB incoming and outgoing terminals for 4 pole upto100A MCCB complete. (Set of 8)

1 Set

47

Making trench of suitable width and depth in hard murum /tar road for laying provided LT cable of 16 sq. mm & aboveand covered with half round hume pipe complete as perspecification no. CW-EXN-CTR

50 Mtr

Page 6

48

Making trench of suitable width and depth in soft soil forlaying provided LT cable of 16 sq. mm & above andcovered with half round hume pipe complete as perspecification no. CW-EXNCTR

250 Mtr

49

Making cement concrete for foundation or concrete fillingin 1:3:6 ratio with 20 to 25 mm . stone metal duly plasteredwith necessary curing for pole muffing or any otherpurpose.

5 Cubic Mtr

Total Amount of Part - D Electrical Work


Page 7

SUMMARYvnit.ac.in/stores/wp-content/uploads/2019/12/schedule-b2-signed.pdf8 Excavation for...

Documents

Transcript of SUMMARYvnit.ac.in/stores/wp-content/uploads/2019/12/schedule-b2-signed.pdf8 Excavation for...