instruCtion manualmodel: KC-240m

7” industrial planer/moulder

COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

04/2017

WarrantY inFormation

2-Year limited WarrantY

For tHis 7” plner/moulder

KinG Canada toolsoFFers a 2-Year limited WarrantY

For CommerCial use.

prooF oF purCHase

Please keep your dated proof of purchase for warranty and servicing purposes.

replaCement parts

Replacement parts for this product are available at our authorized King Canada service centres across Canada.limited tool WarrantY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to theoriginal retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free fromdefects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence oraccidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be liablefor death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorizedKing Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorizedservice centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if any part orparts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.

note to user

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

parts diaGram & parts listsRefer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

KinG Canada inC. dorVal, quÉbeC, Canada H9p 2Y4

www.kingcanada.com

General saFetY instruCtions

VoltaGe WarninG: Before connecting the machine to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same asthat specified on the nameplate. A power source with voltage greater than specified can result in SERIOUS INJURY to the user - as well as damagethe machine. If in doubt DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate is harmful to the motor.

1. KnoW Your maCHineRead and understand the owners manual and labels affixed tothe machine. Learn its application and limitations as well as itsspecific potential hazards.

2. Ground tHe maCHine.This machine is equipped with an approved 3-conductor cord anda 3-prong grounding type plug to fit the proper grounding typereceptacle. The green conductor in the cord is the grounding wire.neVer connect the green wire to a live terminal.

3. Keep Guards in plaCe.Keep in good working order, properly adjusted and aligned.

4. remoVe adJustinG KeYs and WrenCHes.Form habit of checking to see that keys and adjusting wrenchesare removed from the machine before turning it on.

5. Keep WorK area Clean.Cluttered areas and benches invite accidents. Make sure the flooris clean and not slippery due to wax and dust build-up.

6. aVoid danGerous enVironment.Don’t use machinery in damp or wet locations or expose them torain. Keep work area well lit and provide adequate surroundingwork space.

7. Keep CHildren aWaY.All visitors should be kept a safe distance from work area.

8. maKe WorKsHop CHild-prooF.Use padlocks, master switches or remove starter keys.

9. use proper speed.A machine will do a better and safer job when operated at theproper speed.

10. use riGHt tool.Don’t force the machine or the attachment to do a job for which itwas not designed.

11. Wear proper apparel.Do not wear loose clothing, gloves, neckties or jewelry (rings,watch) because they could get caught in moving parts. Non-slip

footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows.

12. alWaYs Wear saFetY Glasses.Always wear safety glasses (ANSI Z87.1). Everyday eyeglassesonly have impact resistant lenses, they are not safety glasses.Also use a face or dust mask if cutting operation is dusty.

13. don’t oVerreaCH.Keep proper footing and balance at all times.

14. maintain maCHine WitH Care.Keep machine clean for best and safest performance. Follow instructions for lubricating and changing accessories.

15. disConneCt maCHine.Before servicing, when changing accessories or attachments.

16. aVoid aCCidental startinG.Make sure the switch is in the ‘’OFF’’ position before plugging in.

17. use reCommended aCCessories.Consult the manual for recommended accessories. Follow the instructions that accompany the accessories. The use of impro-per accessories may cause hazards.

18. neVer stand on tool.Serious injury could occur if the machine tips over. Do not storematerials such that it is necessary to stand on the machine toreach them.

19. CHeCK damaGed parts.Before further use of the machine, a guard or other parts that aredamaged should be carefully checked to ensure that they will operate properly and perform their intended function. Check foralignment of moving parts, breakage of parts, mounting, and anyother conditions that may affect its operation. A guard or otherparts that are damaged should be properly repaired or replaced.

20. neVer leaVe maCHine runninG unattended.Turn power ‘’OFF’’. Don’t leave any machine running until it comesto a complete stop.

1. Always wear eye protection when operating any machine. 2. Before starting up, recheck to make certain all holding screws are

tight. 3. Always stop motor and disconnect the power source before making

any kind of adjustment. 4. Be sure all guards are in place before operating equipment. Ensure

the chip deflectors are in place, with proper gaps between blades.Ensure all covers are secured.

5. Read the instruction manual thoroughly and familiarize yourself withthe machine before attempting to operate.

6. Keep children away,all visitors should maintain a safe distance fromthe machine.

7. After a long period of operation, stop the machine, disconnect thepower, and check the cutter head screws for tightness.

8. Don’t force-feed your work through the machine. Allow the feedrollers to feed the workpiece through the machine automatically.

9. Check the feed roller bearings occasionally to be sure there are no

wood chips between the bearings and side plates. If bearings arenot seated firmly, the feed rollers will not hold stock firmly againstthe table, and kickback could occur.

10. Use proper materials free from loose or tight knots, and avoid materials that are warped or misshapen.

11. Never stand directly in line with either the infeed or outfeed sidesof the machine. Always stand to one side. With any power tool,kickback is always a possibility.

12. Never remove more than 1/8” of material in a single pass throughthe machine.

13. Never plane a board less than 8” in length. 14. Do not push or force stock into the cutterhead. The moulder will

perform better and safer when working at the rate for which it wasdesigned.

15. Always use clean, properly sharpened knives. Dirty or dull knivesare unsafe and can lead to accidents.

speCiFiC saFetY instruCtions For planer/moulders

eleCtriCal inFormation

WarninGALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUSINJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE.FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!

poWer supplYWarninG: YOUR PLANER/MOULDER MUST BE CONNECTED TOA 220V, 15-AMP. MINIMUM BRANCH CIRCUIT. FAILURE TO CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK ORFIRE.

GroundinGThis Planer/Moulder must be grounded. If it should malfunction orbreakdown, grounding provides a path of least resistance for electriccurrent, to reduce the risk of electric shock. This Planer/Moulder isequipped with a cord having an equipment-grounding conductor. Theplug must be plugged into an appropriate outlet that is properly installedand grounded in accordance with all local codes and ordinances.

WarninG: TO MAINTAIN PROPER GROUNDING OF YOURPLANER/MOULDER, DO NOT REMOVE OR ALTER THE PLUGGROUNDING PRONG IN ANY MANNER.

Not all outlets are properly grounded. If you are not sure if your outletis properly grounded, have it checked by a qualified electrician.

WarninG: IF NOT PROPERLY GROUNDED, THIS PLANER/MOULDER CAN CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP LOCATIONS. TO AVOIDSHOCK OR FIRE, IF THE POWER CORD IS WORN OR DAMAGEDIN ANY WAY, HAVE IT REPLACED IMMEDIATELY.

220V operationYour Planer/Moulder comes wired for 220V operation. The plug and therequired wall outlet are illustrated in Fig.1.

eXtension CordsWarninG! IT IS NOT RECOMMENDED TO USE AN ExTENSIONCORD, BUT IF IT IS NECESSARY, READ THE FOLLOWING.

The use of any extension cord will cause some loss of power. Depending on the length of extension cord needed, use the table (Fig.2)to determine the minimum wire gauge (A.W.G-American Wire Gauge).Use only 3-wire extension cords which have 3-prong grounding typeplugs and 3-hole receptacles which accept the tool’s plug.

For circuits that are further away from the electrical circuit box, the wirethickness must be increased proportionately in order to deliver amplevoltage to the Planer/Moulder motor. The smaller the gauge of the extension cord, the thicker it will be in diameter. Refer to Fig.2 for wirelength and size.

starting and stopping the planer/moulder CutterheadThe magnetic switch (A) Fig.3 is located on the front right side of themachine. To turn the machine “On” press the green button (B). To stopthe machine, push the red emergency stop button (C). Once you pushdown on the emergency stop button (C), twist the button clockwise untilit pops up, only then will you be able to restart the machine.

starting and stopping the automatic feed rollersThis machine is supplied with an independent motor which operatesthe feed rollers. This motor is controlled by the On/Off switch (D) Fig.3,it comes with a removable safety key (E). When the safety key is removed from the switch and placed in a safe location, unauthorizedpersons or children can’t turn the switch to the On position.

reset button (overload protector)This machine comes with an overload reset button (F) Fig.3. If the machine motor overheats, a safety mechanism stops the motor automatically. To prevent motor over-heating, reduce load on motor orcheck voltage. Allow motor to cool down, then press the reset buttonand restart the machine. If the machine does not restart, wait an additional 5 minutes before restarting.

FiGure 2

properlY Grounded 220V outlet

Current CarrYinG pronGs

GroundinG pronG

FiGure 1

LENGTH OFExTENSION CORD

0-25 FEET26-50 FEET

51-100 FEET

WIRE GAUGE REQUIRED(AMERICAN WIRE GAUGE)

220V LINESNO.16NO.14NO.12

FiGure 3

GettinG to KnoW Your 7” planer/moulder

1. Cutterhead height adjustment handwheel2. Drive belt safety guard3. Cutterhead lock handle4. Moulding guide fence (1 of 2)5. Guide fence lock knob (1 of 4)6. Table Extension Rollers7. Cutterhead activating magnetic safety switch8. Power cord9. Front access panel10. Feed motor switch with safety key11. Thermal relay reset button12. Variable feed rate control dial13. Table14. Feed motor15. Dust Hood16. Elliptical jig assembly17. Elliptical jig mounting bracket

speCiFiCationsmodel KC-240mMaximum planing width 7”Maximum moulding width 6-3/4”Maximum thickness of stock 8”Minimum thickness of stock 1/4”Minimum length of stock 8”Maximum depth of cut (planing/moulding) 1/8” / 3/4”Cutterhead speed 7,000 RPMNumber of knives 2Motor 2 HP, 12 Amp.Voltage 220V, 1 phase, 60 HzAssembled dimensions (LxWxH)/weight 32” x 27-1/2” x 51” / 290 lbsPackage dimensions (LxWxH)/weight 36-1/4” x 30” x 49-1/4” / 355 lbs

assemblY & setup

installinG tHe CutterHead HeiGHt adJustment HandWHeel

To install the cutterhead height adjustment handwheel:

1. Loosen the set screw (A) Fig.4 on the handwheel (B) using a 3mm hex. key sothat the handwheel can slide onto the shaft (C).

2. Attach the adjustment handwheel (B) to the shaft (C).

3. Retighten the set screw (A) to secure the handwheel.

remoVinG proteCtiVe plastiC and Foam

This machine is shipped from the factory with the cutterhead resting on a styrofoam block for support during transport. To remove the styrofoam block:

1. Loosen the cutterhead lock handle (A) Fig.5.

WarninG! Do not attempt to adjust the height of the cutterhead without firstloosening the cutterhead lock handle (A) Fig.5. Failure to do this could cause premature wear of the locking mechanism.

2. After loosening the lock handle, rotate the cutterhead height adjustment handwheel (B) counterclockwise to lift the cutterhead off of the styrofoam block(C), remove styrofoam.

To remove the protective plastic sheet:

1. Loosen the fence lock knobs (A) Fig.6 and remove the two fences (B) from thetable.

2. Pull back the protective plastic (C) and discard it.

This machine is shipped from the factory with a protective coating on the table toprevent rust during shipping and storage. This coating can be removed by wipingthe table with a rag soaked in kerosene, mineral spirits, or paint thinner. A plasticscrapper can also be used to scrape off most of the coating, being careful not toscratch the table.

mountinG tHe maGnetiC saFetY sWitCH

The magnetic safety switch and mounting bracket (A) Fig.7 must be mounted tothe right side of the machine using two round head allen screws (B) which are already mounted to the right side of the machine as shown.

FiGure 4

FiGure 5

FiGure 6

FiGure 7

assemblY & setup

installinG tHe belt on tHe driVe pulleYs

To install the belt on the drive drive pulleys:

1. Using the 6mm hex. key, remove the cap screw and washer (A) Fig.8 which isused to secure the motor during transport. Once the screw has been removed,the motor will swing freely.

2. Next, loosen and remove the 3 round head allen screws (A) Fig.9 using a 4mmhex. key. Lift and remove the upper pulley cover (B).

3. Make sure the drive belt (C) is installed on the upper pulley (D) as shown.

4. Using the 4mm hex. key, loosen and remove the 4 round head allen screws(A) Fig.10. Remove the rear access panel (B) from the stand in order to accessthe motor.

5. Lift the motor (A) Fig.11 up and install the other end of the drive belt (B) in theslot on the lower pulley (C).

6. Re-install the upper pulley cover and the rear access panel.

FiGure 8

FiGure 9

FiGure 10

FiGure 11

assemblY & adJustments

installinG leVelinG rubber Feet to tHe stand

1. Install the 4 leveling rubber feet (A) Fig.12 to each stand leg (B) using a washer(C) and two hex. nuts (D) as shown in Fig.12. Adjustments can be made toeach leveling rubber foot by loosening the top hex. nut, moving the bottom hex.nut up and down to the desired height, and retightening the top hex. nut.

settinG tHe deptH oF Cut

The depth of cut is set by raising and lowering the cutterhead. To adjust the depthof cut:

1. Loosen the cutterhead lock handle (A) Fig.13 by turning it counterclockwise.

2. Turn the cutterhead handwheel (B) clockwise to raise the cutterhead, and counterclockwise to lower the cutterhead.

note: Each 1/3rd rotation of the cutterhead handwheel in either direction willraise or lower the cutterhead approximately 1/32”. The depth scale and pointer(C) on the machine is intended to be used for reference only, but not for high precision measurements.

3. Retighten the lock handle (A) to secure the cutterhead in the desired position.

CHanGinG tHe Feed rate

The feed motor is capable of speeds from 3 FPM (feet per minute) to 20 FPM.The feed rate can be adjusted using the feed rate adjustment knob (A) Fig.14.Turn the knob clockwise to increase the feed rate, and counterclockwise to decrease the feed rate.

note: Determining correct feed rate will depend on the work material, the size ofthe material, and the aggressiveness of the cut. In general, softer woods shouldbe planed or moulded at a high speed, and hardwoods should be planed ormoulded at a slower speed. Additionally, wider or more aggressive cuts should beplaned or moulded at slower speeds. Narrow or lighter cuts can be planed ormoulded at a higher rate.

settinG tHe KniVes For planinG

inspeCtinG tHe KniVes

It’s important to ensure that the two knives are installed and set at the exact sameheight as the cutterhead. In order to verify that they are set at the same height, agauge block will need to be used. The planer knives are set properly from the factory, but we suggest verifying this before the first use.

note: If your planer knives have become dull or damaged, the planer knivesmust be replaced. An optional 2 pc. replacement knife set (model KKC-7M) isavailable, please contact your retailer of King Canada products for more information.

1. Create a gauge block by using a piece of hardwood and following the dimensions shown in Fig.15.

FiGure 12

FiGure 13

FiGure 14

FiGure 15

inspeCtinG tHe KniVes continued...

Warning! Make sure the machine is turned off, and disconnected from the powersource.

2. Loosen the three round head allen screws (A) Fig.16, slide and remove the topcover (B) to expose the cutterhead and knives.

3. Slowly rotate the pulley (A) Fig.17 by hand, until either of the knives reaches itslowest point as shown in Fig.18.

4. Place the gauge block (A) Fig.18 underneath the cutterhead as shown.

5. Adjust the cutterhead height so that it is lightly touching the gauge block (asshown in Fig.18), but is still able to move back and forth past the gauge block.The height of the cutterhead is adjusted by loosening the cutterhead lock handle, and rotating the cutterhead height handwheel (See section “Settingthe depth of cut”). Retighten the lock handle when the cutterhead is set.

settinG tHe First KniFe parallel to tHe table

1. Make sure each knife installed in the cutterhead is parallel to the table by usingthe gauge block (A) Fig.19 to check both ends of the cutterhead as shown inFig.19.

FiGure 16

FiGure 17

FiGure 18

FiGure 19

adJustments

settinG tHe First KniFe parallel to tHe table continued...

If the knife is not set parallel to the table:

2. Slowly rotate the upper pulley by hand until the T-handle wrench (A) Fig.20 willfit into the holes in the cutterhead shaft as shown. This will prevent the cutterhead from rotating while adjusting the blade.

3. Move the chip deflector (A) Fig.21 away of the cutterhead, loosen the 3 roundhead allen screws (B) using the 4mm T-handle hex. key.

4. Loosen the two middle locking bolts (A) Fig.22 all the way using the a 14mmwrench. Loosen the two locking bolts (B) on the end slightly, so that they arestill able to hold the knife.

5. Loosen the hex. nut (C) Fig.22 on the top of the knife, and then adjust the firstset screw (D) to raise and lower the knife until it is lightly touching the gaugeblock.

6. Retighten the hex. nut (C) and make sure the knife is still parallel with the tableby using the gauge block on both ends of the knife.

7. Move the gauge block to the other side and repeat steps 5-6 for the secondhex. nut/set screw (E). Retighten the four locking bolts shown in Fig.22.

settinG tHe HeiGHt oF tHe seCond KniFe

1. Remove the T-handle wrench from the first knife, turn the cutterhead 180°, andreinsert the T-handle wrench to lock the other knife in place.

2. Using the gauge block, check to see that the second knife is set at the sameheight. If it is set higher or lower than the first knife, repeat steps 4-7 with thesecond knife. make sure both knives are set to the same height, and bothknives are parallel with the table.

adJustinG inFeed and outFeed rollers

The infeed roller (A ) Fig.23 and outfeed roller (B) come from the factory set at aheight of 0.030” below the lowest point of the cutterhead. We suggest verifyingthey are set at the correct height before first use.

NOTE: This step can only be done once the knives have been checked to ensurethey are set at the same height, and are parallel with the table. Follow the stepsunder “SETTING THE CUTTING KNIVES FOR PLANING” before adjusting thefeed rollers.

FiGure 20

FiGure 21

FiGure 22

FiGure 23

adJustments

adJustinG tHe HeiGHt oF tHe Feed rollers

The feed rollers (A & B) Fig.24 are set at 0.030” below the lowest point of thecutterhead (C) so that they are able to grip the workpiece as it is fed through themachine as shown in Fig.24. If the feed rollers are set above the lowest point ofthe cutterhead, it could cause the workpiece to be ejected at high speed as shownin Fig.25.

WarninG! Failure to set the feed rollers at the proper height could potentiallylead to serious injury and workpiece kickback.

Adjusting feed rollers at the correct height:

1. Place a 0.030” feeler gauge (A) Fig.26 on top of the gauge block (B), and placethem both under the cutterhead (C). Lower the cutterhead so that it lightlytouches the feeler gauge when moving back and forth at its lowest point.

2. Lock the cutterhead in position using the cutterhead lock handle, and place thegauge block (B) underneath the infeed roller (D) as shown. The infeed rollershould lightly touch the top of the gauge block with the 0.030” feeler gauge removed.

3. If the infeed roller needs to be adjusted, loosen the lock nuts (A) Fig.27 on thein-feed adjustment screws (B), and rotate the adjustment screws until theinfeed roller is lightly touching the gauge block on both ends. Retighten thelock nuts once the infeed roller is in the proper position.

4. Place the gauge block underneath the outfeed roller. If the out-feed roller needsto be adjusted, loosen the lock nuts (C) Fig.27 on the outfeed adjustmentscrews (D), and rotate the adjustment screws until the outfeed roller is lightlytouching the gauge block on both ends. Retighten the lock nuts once the out-feed roller is in the proper position.

NOTE: Lowering the feed rollers too much could put too much tension on the drivechains, which could result in breakage. To avoid this, use the number of visiblethreads on the adjustment screws as a reference. You should not be able to countmore than 5 threads on these screws. If the feed rollers have been lowered totheir lowest point and they still do not touch the gauge block, the depth of cut willneed to be adjusted to make up the difference.

FiGure 24

FiGure 25

FiGure 26

FiGure 27

adJustments

eXtendinG tHe Feed roller liFe

For most moulding cuts, the feed rollers will need to be adjusted. This will depend on the type of moulding cutter beingused. When making deeper cuts, or for larger profiles, theheight of the feed rollers can be adjusted by turning the screws(B) & (D) Fig.27 approximately two turns at a time. This willcompensate for the material that has been removed from theworkpiece.

NOTE: To prevent the workpiece from damaging the feedrollers, make sure the workpiece never exceeds 1/4” of theheight of the feed rollers as shown in Fig.28.

adJustinG tHe Feed roller pressure

Over time, the feed rollers may need to be adjusted to ensure they are applying the correct amount of downward pressure on the workpiece. Withnormal use and wear, one or both of the feed rollers may need to be adjusted to correct snipe (when the workpiece is cut too deeply at either end).

If snipe is occurring at the beginning of the workpiece (most common):

1. Reduce the amount of pressure applied by the infeed roller by loosening the infeed lock nuts (A) Fig.27 and rotating the adjustment screws (B)counterclockwise.

If snipe is occurring at the end of the workpiece:

2. Reduce the amount of pressure applied by the outfeed roller by loosening the outfeed lock nuts (C) Fig.27 and rotating the adjustment screws(D) counterclockwise.

3. Continue to fine-tune this adjustment until the snipe has been corrected.

installinG mouldinG KniVes

1. Make sure that the machine is turned off, and disconnected from the powersource. Remove the top cover (A) Fig.16 by removing the three round head allenscrews (B).

2. Slowly rotate the upper pulley by hand until the T-handle wrench will fit into theholes in the cutterhead shaft as shown in Fig.20. This will stop the cutterheadfrom rotating while changing knives.

3. Use the 14mm wrench to loosen and remove the four locking bolts (A) Fig.29.

4. Carefully remove the cutter knife (B).

5. Repeat steps for the second knife on the other side of the cutterhead.

6. Make sure that the set screws (A) Fig.30 do not stick out past the inner face ofthe cutterhead as shown. Make sure that the nuts (B) are fastened properly sothat the cutting knife sits flush with the lip. Failure to to this could result in seriousinjury or damage to the machine.

7. Install the moulding knife (C) (not included) so that it is flush with the lip on thecutterhead, with the beveled side of the moulding knife facing up and away fromthe cutterhead as shown.

FiGure 28

FiGure 29

adJustments

FiGure 30

installinG mouldinG KniVes continued...

8. Install the moulding knife (A) Fig.31 as close to the center as possible, andfasten the knife in place with two locking bolts through the mounting holes ofthe moulding knife. Make sure that the moulding knife is flush with the bottomlip of the cutterhead while tightening the bolts.

9. Take a perfectly square block of wood (A) (with dimension roughly 1” x 1” x 5”)up against the right fence (B) as shown in Fig.32.

10. With the cutterhead positioned low enough that the side of the moulding knifewill make contact with the block, slide the fence over until the two are touchingas shown in Fig.32. Lock the fence in place using the fence lock knobs (C)Fig.32.

11. Remove the T-handle wrench (A) Fig.20 from the cutterhead. Slowly rotatethe upper pulley by hand 180° until the T-handle wrench will fit into the holeson the other side of the cutterhead.

12. Repeat steps for the second moulding knife on the other side of the cutterhead.

13. Make sure the second moulding knife is aligned with the first moulding knifeby rotating the cutterhead 180° and ensuring it lightly rubs against the woodblock (A) Fig.32. If they are not aligned properly, loosen the two bolts (B) Fig.31that secure the moulding knife (A), and re-adjust the moulding knife until it isaligned properly while retightening the bolts (B).

settinG tHe CHip deFleCtors

1. Loosen the three round head allen screws (A) Fig.33 on the flat chip deflector(B) so that it moves freely. Position the deflector so that there is a 1/8" gap between the deflector and the edge of moulding knife.

2. Rotate the cutterhead 180°. Loosen the two round head allen screws (A) Fig.34on the curved chip deflector (B) so that it moves freely. Position the deflectorso that there is a minimum 1/4” gapbetween the deflector and the edge of themoulding knife.

FiGure 31

adJustments

FiGure 32

FiGure 33

FiGure 34

operation

operation

This machine is designed to remove material from the top surface of a workpiece,to either plane the workpiece down to a desired thickness, or mould the workpieceand apply a specific profile and thickness. For best results, the workpiece musthave at least one side that has been machined perfectly flat. The perfectly flat faceof the workpiece should face downward on the table.

seleCtinG materials For planinG and mouldinG

this machine is meant for use with solid woods, or mdF only. Other materialsshould NOT be used with this machine.

For best results, the workpiece should always be planed or moulded IN THE SAME DIRECTION AS THE GRAIN as shown in Fig.35. Planing ormoulding against the direction of the grain could cause the workpiece to shatter, potentially leading to serious injury or damage to the machine.

Before using a workpiece with this machine, inspect it to make sure that it is free from nails, staples, and other foreign objects. Failure to do thiscould result in serious injury and damage to the machine. Remove all foreign objects from the workpiece before feeding it through the machine.

Avoid lumber with loose or protruding knots, and lumber that is twisted or deformed. Knotted or deformed lumber increases the risk of jamminginside the machine, kickback, or cause the workpiece to be ejected from the machine at high speed. This could potentially lead to serious injuryor damage to the machine.

maXimum WorKpieCe dimensions

planing / moulding Workpiece limits (Fig.36)Maximum Planing Width: 7”Maximum Moulding Width: 6-3/4”Maximum Workpiece Thickness: 8”Minimum Workpiece Thickness: 1/4”Minimum Workpiece Length: 8”

note: Respect the limits of this machine and abide by the rated limits. Failure tofollow these guidelines could result in serious injury, or damage to the machine. Donot use this machine if the workpiece dimensions are outside of these rated limits.

maXimum deptH oF Cut

maximum depth of CutWidth Type of Wood Moulding Planing

Depth of Cut1” Poplar 1/4” or less 1/8” or less1” Red Oak 3/16” or less 1/8” or less3” White Pine 3/16” or less 1/8” or less3” White Oak 1/8” or less 1/8” or less6” Poplar 1/8” or less 1/8” or less6” Red Oak 1/16” or less 1/8” or less

note: This information is intended to serve as a general guideline. Optimal depth of cut will vary based on other factors such as workpiece width,the moisture content of the material, and the density of the material.

note: As a general guideline, removing a smaller amount of material with a greater number of passes through the machine is preferred overusing more aggressive cuts and fewer passes. This will help to extend the life of the knives, and result in a better finish quality.

FiGure 35

FiGure 36

operation

ConneCtinG to a dust ColleCtor

This machine is equipped with a 4” dust chute (A) Fig.37, it is used for connectingto a dust collector. Ensure that the correct size fittings and hose are used to minimize airborne dust.

planinG

1. Make sure the machine is turned off. Place the workpiece on the table with theside that bas been machined perfectly flat facing DOWN, and the side that willbe planed facing UP.

2. Position the fences (A) Fig.38 against both edges of the workpiece (B), beingcareful not to pinch the workpiece so that can still slide freely.

3. Place the workpiece up against the cutterhead, loosen the cutterhead lock handle (C) Fig.28, and use the adjustment handwheel to raise or lower the cutterhead to set the desired depth of cut. Retighten the lock handle to securethe cutterhead in place.

note: The depth scale (D) Fig.38 on the front of the machine is intended to beused for reference, but not for high-precision measurements.

4. If there is a dust collector connected, turn it on first. Then press the green “ON”button on the magnetic switch to start the cutterhead motor.

5. Then, make sure the feed motor speed has been set to the minimum value before starting the feed motor. Move the feed motor switch to the “ON” positionto start the feed motor. Slowly increase the feed speed until the desired feedrate has been reached.

6. Standing on one side of the machine, place the workpiece on the infeed table.Ensure that the flat side of the workpiece is facing down, the face to be planedis facing up, and the workpiece will be fed in roughly the same direction as thegrain of the wood as shown in Fig.39.

7. Slowly feed the workpiece into the machine, until the infeed roller “grips” theworkpiece. Once the infeed roller has taken over, let go of the workpiece andallow it to feed automatically through the planer.

8. Move to the other side of the machine. Remove the workpiece once it hascleared the outfeed roller and has stopped moving through the machine.

note: Do not push, pull, or adjust the workpiece once the infeed roller has takenover. This is an automatic process, and interfering could cause damage to the machine, workpiece, or cause serious injury.

mouldinG

1. Make sure the machine is turned off and disconnected from the power source.a. If only the face of the workpiece is being profiled, cut the workpiece to its final

width. b. If the edges of the workpiece are also being cut by the knives, cut the workpiece

so that it is 1/32” wider than its final width.

note: Planing and cutting all workpieces to their final width and height is recommended before setting up the moulder for any profile work.

2. Position the fences (A) Fig.40 against both edges of the workpiece (B), beingcareful not to pinch the workpiece so that can still slide freely.

3. Place the workpiece underneath the cutterhead. Loosen the cutterhead lockhandle (C) Fig.38 and use the adjustment handwheel to lower the cutterheaduntil it lightly makes contact with the workpiece.

4. Make sure the workpiece is properly aligned with the moulding knife. If needed,reposition the fences to properly align the workpiece. Raise the cutterheadslightly and remove the workpiece.

5. Loosen the cutterhead lock handle, and move the cutterhead downward byrotating the handwheel counterclockwise one full turn. This results in a 3/32” depth of cut. Retighten the lock handle to secure the cutterhead.

6. Follow steps 4-8 from the above section “PLANING”.

FiGure 37

FiGure 38

FiGure 39

FiGure 40

operation

mouldinG CurVed pieCes usinG tHe elliptiCal JiG

The elliptical jig allows this machine to handle curved workpieces. To mould curvedworkpieces, the workpiece is usually secured to a template that rides along theinner and outer guide bearings of the jig as shown in Fig.41.

When doing full width profile cuts, the workpiece (A) Fig.41 and template (B) mustbe the exact same width as the profile (C). This is not required if the profile onlycuts a portion of the width of the workpiece.

Ideally, templates should be made from 3/4” MDF (A) Fig.42, and should be made4” longer than the workpiece at each end of workpiece (B). The minimum length ofcurved workpiece that can be safely moulded is 9”.

To secure the workpiece to the template, pre-drill counter-sunk mounting holes fromthe underside of the template (A) Fig.43. Mounting hole placement will depend onthe workpiece. For each new workpiece, different positioning of the mounting holes,and/or different screws may be required to avoid interference with the cutterhead.

Use flathead wood screws that are the proper length, so that the cutterhead doesnot come into contact with the tops of the screws (B) Fig.43. Additionally, ensurethat the screws do not protrude from the bottom surface of the template (C). Thiscould scratch the table, and/or interfere with the moulding process.

1. Make sure the machine is turned off. Remove the two fences. Raise the cutterhead to allow for better access to the table.

2. Install the elliptical jig guide bearings and mounting bracket (A) Fig.44 to the frontof the table using two cap screws and washers (B). Install the outer idler guidebearing (C) using two round head allen screws (D).

FiGure 41

FiGure 42

FiGure 43

FiGure 44

operation & maintenanCe

mouldinG CurVed pieCes usinG tHe elliptiCal JiG continued...

3. Lower the cuttinghead until it lightly touches the workpiece (A) Fig.45 to align theguide bearings with the cutting knife.

4. Loosen the jam nut (A) Fig.46 on the inner guide, and rotate the adjustment knob(B) until the bearings are aligned with the cutting knife. Retighten the jam nut (A)to secure the bearings in place.

5. Place the workpiece flush with the inner guide bearings (C) Fig.46, and loosenthe round head allen screws (D) on the outer idler guide bearing (E). Adjust thebearing so that it is flush with the outside face of the workpiece. Retighten theround head allen screws to secure the bearing in place.

6. Raise the cutterhead slightly and remove the workpiece. Loosen the cutterheadlock handle, and move the cutterhead downward by rotating the handwheelcounterclockwise one full turn. This results in a 3/32” depth of cut. Retighten thelock handle to secure the cutterhead.

note: Before making any passes through the machine, ensure that the knife isfree from interference from anything besides the workpiece. If the cutting knifecomes into contact with the guides, bearings, screws, or any object other than theworkpiece, it could cause serious damage to the machine and/or cause serious injury.

reGular maintenanCe CHeCKlist

1. Inspect the ON/OFF switches, and power cord/plug before each use. 2. Make sure the knives are secured properly to the cuttinghead.3. Ensure that the feed rollers are set properly.4. Ensure that the workpiece material is suitable for planing or moulding.

periodiC maintenanCe CHeCKlist

1. Occasionally coating the table surface with paste wax can help protect the tablesurface, and make it easier for the workpiece to slide along it.

2. Regularly inspect planed or moulded workpieces for signs of wear or damage tothe cutting knives. Replace worn or damaged cutting knives immediately.

3. Avoid the use of silicon based products on the machine, as these could interferewith wood finishing products.

lubriCatinG tHe driVe CHain/Gears

Occasionally lubricating the drive chain and gears will help maintain a smooth andproblem-free feeding action, and lengthen the life of the machine.

To clean and lubricate the drive chain and gears:

1. Make sure the machine is turned OFF and disconnected from the power source. 2. Remove the round head allen screw (A) Fig.47 and the round head allen screws

on the back (B) holding the front panel in place. Remove the front panel (C). 3. Remove the old grease and dust by wiping the drive chain and gears with a dry

rag. 4. Apply a generous coating of common automotive bearing grease to the gears

(A) Fig.48, chain (B), and elevation screw (C). 5. Reposition the front panel and retighten the screws to secure it in place.

FiGure 45

FiGure 46

FiGure 47

FiGure 48