Flange Live Flange Live loading Flange Live Flange Live loading
741 Flange
Transcript of 741 Flange
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 1/8
Style 741
Style 741 Vic-Flange® adapter is designed for directly incorporating flanged components
with ANSI CL. 125 or CL. 150/PN10 and PN16 bolt hole patterns into a grooved pipe
system. Sizes 2 – 12"/50 – 300 mm are hinged for easy handling with integral end tabs
which facilitate assembly. Sizes 14 – 24"/350 – 600 mm are cast in four (4) identical
segments which are interconnected as assembly is completed.
The design incorporates small teeth inside the key shoulder I.D. to prevent rotation
(excluding 159 mm size). These teeth should be removed when Vic-Flange adapter is
utilized with a Victaulic Series 700 grooved end butterfly valve, Schedule 5 pipe or
plastic pipe.
Vic-Flange adapters may only be used on Vic-300® butterfly valves on one side in 2 –
8"/50 – 200 mm sizes. They are not recommended for 10 and 12"/250 and 300 mm
sizes.
Vic-Flange adapter Style 741 is not recommended for use with Victaulic Series 709
butterfly valves (contact Victaulic for recommendations). They may only be used on one
side of Victaulic Series 700 butterf ly valve, sizes 2 – 4"/50 – 100 mm fitted with standard
or lever-lock handles. Vic-Flange adapter must be assembled so it does not interfere with
handle operation.
Style 743
Vic-Flange Style 743 flange-to-groove adapter permits direct connection of ANSI Class
300 flanged components into a grooved system. The two-piece, hinged housing engages
into the pipe groove and bolts directly to any standard flanged component. The
conventional bolt hole pattern allows for easy, fast assembly. Style 743 rotates 360° for
proper alignment of bolt holes before tightening. Vic-Flange gaskets utilize the Victaulic
pressure-responsive design, sealing on the pipe end and directly to the opposing flange
face. No standard flange gasket is required.
Style 743 is designed to mate with raised-face flanges, but can be used with flat-face
flanges by removing the raised projections on the outside face of the flange.
VIC-FLANGE NOTES Because of the outside flange dimension, Vic-Flange should not be used within 90° of one another
on a standard fitting. When wafer or lug-type valves are used adjoining a Victaulic fitting, check disc
dimensions to assure proper clearance.
Vic-Flange adapters should not be used as anchor points for tie-rods across non-restrained joints.
Mating rubber faced flanges, valves, etc., requires the use of a Vic-Flange washer.
Vic-Flange gaskets must always be assembled with the color coded lip on the pipe and the other lip
facing the mating flange.
06.06_1
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
JOB/OWNER CONTRACTOR ENGINEER
System No. __________________________ Submitted By ________________________ Spec Sect ____________ Para __________
Location ____________________________ Date ________________________________ Approved ___________________________
Date ________________________________
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS
STYLE 741
2 – 12" SIZES
STYLE 741
14 – 24" SIZES
STYLE 743
Exaggerated for clarity
Exaggerated for Clarity
Exaggerated for clarity
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 2/8
Housing: Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM
A-395, grade 65-45-15, is available upon special request.
Housing Coating: Black enamel.
• Optional: Hot dipped galvanized and others.
Coupling Gasket: (specify choice‡)
• Grade “E” EPDM
EPDM (Green color code). Temperature range –30°F to +230°F/–34°C to +110°C.
Recommended for hot water service within the specified temperature range plus a variety of
dilute acids, oil-free air and many chemical services. UL classified in accordance with ANSI/
NSF 61 for cold +86°F/+30°C and hot +180°F/+82°C potable water service. NOT
RECOMMENDED FOR PETROLEUM SERVICES.
• Grade “T” nitrile
Nitrile (Orange color code). Temperature range –20°F to +180°F/–29°C to +82°C.
Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the
specified temperature range; except hot, dry air over +140°F/+60°C and water over +150°F
+66°C. NOT RECOMMENDED FOR HOT WATER SERVICES.
‡ Services listed are General Service Recommendations only. It should be noted that there are
services for which these gaskets are not recommended. Reference should always be made to the
latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a
listing of services which are not recommended.
Draw Bolts: 14 – 24"/350 – 600 mm only: Heat-treated plated carbon steel, trackhead meeting the
physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183.
MATERIAL SPECIFICATIONS
06.06_2
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 3/8
DIMENSIONS
W
Z
YX
STYLE 741
Sizes 2 – 12"/50 – 300 mm
ANSI Class 125 and 150 Flanges
SizeMax. WorkPressure *
Max. EndLoad * No. Bolts † Bolt Size †
Sealing SurfaceInches/mm Dimensions – Inches/mm
Approx.Wgt. Each
NominalSize
Inchesmm
ActualOutsideDiameter
Inchesmm
psikPa
Lbs.N Required Inches
“A”Maximum
“B”Minimum W X Y Z
Lbs.kg
2 2.3 300 ,3304 5⁄8 x 2 ¾
2.3 3.4 6. 6.00 4. 0. 3.0 60.3 206 920 60 2 2 2 9 .4
2 ½ 2. 300 ,904 5⁄8 x 3
2. 3.9 . .00 .0 0. 4.6 3.0 206 60 3 99 200 40 22 2.
3 3.00 300 2,4 5⁄8 x 3
3.0 4.3 .29 .0 6.00 0.94 .30 .9 206 240 9 2 9 2 24 2.4
4 4.00 300 4,0 5⁄8 x 3
4.0 .3 9. 9.00 .0 0.94 .400 4.3 206 222 4 4 2 229 9 24 3.4
.63 300 ,290 ¾ x 3 ½ .6 6. 0.90 0.00 .0 .00 .62 4.3 206 32440 4 2 24 26 2 3.9
6 6.62 300 0,30 ¾ x 3 ½
6.63 . .90 .00 9.0 .00 9.90 6.3 206 46060 6 9 302 29 24 2 4.
6. mm6.00 300 9,960
¾ x 3 ½6.0 .66 .92 .00 9.4 .00 0.0
6. 206 44320 6 9 303 29 240 2 4.
.62 300 ,00 ¾ x 3 ½
.63 9.94 4.0 3.0 . .3 6.6200 29. 206 29 22 36 343 29 29 .
0 0.0 300 2,22 7⁄8 x 4
0. 2.3 .24 6.00 4.2 .9 24.220 23.0 206 20 23 33 43 406 362 30 .0
2 2.0 300 3,22 7⁄8 x 4
2. 4.3 20.2 9.00 .00 .2 46.300 323.9 206 020 324 364 4 43 432 32 2.2
* Working Pressure and End Load are total, rom all internal and external loads, based on standard weight steel pipe, standard roll or cut grooved inaccordance with Victaulic speciications. Contact Victaulic or perormance on other pipe.
WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to ½ times the igures shown.
† Total bolts required to be supplied by installer, may be ordered rom Victaulic.
IMPORTANT NOTES:
Style 4 Vic-Flange adapters provide rigid joints when used on pipe with standard cut or roll groove dimensions and consequently allow no linear or angularmovement at the joint. When used with Victaulic Series 00 butterly valves, plastic pipe or light wall metallic pipe, small teeth in I.D. o key section shouldbe removed and may be used on one side o the valve. Contact Vic taulic or inormation on AS229 – Table E; ISO 20 4 (PN0); DIN 232 (PN0) and JIS B-220(0K) langes.
A
Max.
B
Min.
Exaggerated for Clarity
Shaded area o mating ace mustbe ree rom gouges, undulationsor deormities o any type oreective sealing.
06.06_3
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 4/8
DIMENSIONS
STYLE 741
Sizes 50 – 300 mm/ 2 – 12"
PN10 and PN16 Flanges
Size PN10 Flanges PN16 FlangesSealing Surface
Inches/mm Dimensions – mm/InchesApprox.
Wgt. Each
NominalSizemm
Inches
ActualOutside
Diametermm
Inches
Max. WorkPressure *
Max. EndLoad * Bolts †
Max. WorkPressure *
Max. EndLoad * Bolts †
“A”Maximum
“B”Minimum W X Y Z
Lbs.kg
Bars *p`si
NLbs.
No.Req’d.
Sizemm
Bars *psi
NLbs.
No.Req’d.
Sizemm
0 60.3 0 204 6
6 464 6
60 6 2 20 .42 2.3 4 640 230 02 2.3 3.4 6.9 6.0 4.92 0.9 3.
6. mm6. 0 440
4 66 2
4 66 03 20 4 20 2.
3.000 4 020 230 63 3.00 4.0 .9 .2 . 0.9 4.
0 .9 0 620 6
6 992 6
9 2 200 60 22 2.43 3.00 4 39 230 2230 3.0 4.3 . . 6.30 0. .4
00 4.3 0 0260 6
6 6420 6
4 4 2 229 0 24 3.4 4.00 4 230 230 3690 4.0 . 9. 9.00 .09 0.94 .
9.0 mm 9.0 0 900 20 6 3400 20 9 30 2 240 26 4.6.20 4 440 230 06 6.2 .36 2.09 .0 9.4 .02 0.0
6. mm6. 0 2400
206 34236
206 9 303 20 240 2 4.
6.00 4 4 230 632 6.0 .6 .93 .00 9.4 .00 0.0
0 6.3 0 2220 20
6 3600 20
6 9 302 29 240 2 4.6 6.62 4 000 230 000 6.63 . .9 0.9 9.4 .00 0.0
200 29. 0 3690 20
6 603202 20
29 22 36 # 342 # 29 # 29 # . .62 4 40 230 3 .63 9.94 4.49 3.46 .6 .4 6.6
20 23.0 0 602 20
6 93692 24
23 33 43 § 39 § 30 § 2 § .00 0.0 4 360 230 20 0. 2.3 .20 . 3. .06 24.2
300 323.9 0 2302 20
6 302 24
324 36 4 ‡ 460 ‡ 400 ‡ 32 ‡ .42 2.0 4 0 230 29620 2. 4.3 .2 . . .26 3.4
* Working Pressure and End Load are total, rom all internal and external loads, based on standard weight steel pipe, standard roll or cut grooved inaccordance with Victaulic speciications. Contact Victaulic or perormance on other pipe.
WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to ½ times the igures shown.
# PN6 dimensions (mm/inches): W = 360/4.; X = 340/3.39; Y = 29/.6; Z = 30/..
§ PN6 dimensions (mm/inches): W = 43/.24; X = 406/.9; Y = 362/4.00; Z = 30/..
‡ PN 6 dimensions (mm/inches): W = 4/.2; X = 444/.; Y = 40/6.4; Z = 32/.26.
† Total bolts required, to be supplied by installer. Bolt sizes or conventional lange-to-lange connection.
Longer bolts required when lange utilized with waer-type valves.
IMPORTANT NOTES: Style 4 Vic-Flange adapters provide rigid joints when used on pipe with standard cut or roll groove dimensions and consequentlyallow no linear or angular movement at the joint. When used with Victaulic Series 00 butterly valves, plastic pipe or light wall metallic pipe, small teeth inI.D. o key section should be removed and may only be used on one side o the valve. Contact Victaulic or inormation on AS229 - Table E; ISO 204 (PN0);DIN 232 (PN0) and JIS B-220 (0k) langes.
AMax.
BMin.
Exaggerated for Clarity
W
Z
YX
Shaded area o mating ace mustbe ree rom gouges, undulationsor deormities o any type oreective sealing.
06.06_4
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 5/8
DIMENSIONS
T
ZV
YB
A
X W
AMax.
BMin.
Exaggerated for Clarity
STYLE 741
Sizes 14 – 24"/350 – 600 mm#
ANSI Class 125 and 150 Flanges
SizeMax. WorkPressure *
Max. EndLoad * Assembly Bolts †
DrawBolts §
Sealing SurfaceInches/mm Dimensions – Inches/mm
Approx.Wgt. Each
NominalSize
Inchesmm
ActualOutside
DiameterInchesmm
psikPa
Lbs.N
No.Req. †
SizeInches
No.Req.
SizeInches
“A”Max.
“B”Min. T V W X Y Z
Lbs.kg
4 4.000 300 46,02 x 4 ½ 4 5⁄8 x 3 ½
4.00 6.39 9.3 0.94 24.0 2.00 . .44 62.030 3.6 206 2000 36 46 492 24 622 33 46 3 2.
6 6.000 300 60,3006 x 4 ½ 4 5⁄8 x 3 ½
6.00 .39 2.0 0.94 2.2 23.0 2.2 .44 9.0400 406.4 206 2633 406 46 46 24 69 9 40 3 3.
.000 300 6,3406 1⁄8 x 4 ¾ 4 ¾ x 4 ¼
.00 20.00 22.2 .00 29.00 2.00 22. .6 2.340 4.0 206 33900 4 0 6 2 3 63 40 3.3
20 20.000 300 94,2020 1⁄8 x ¼ 4 ¾ x 4 ¼
20.00 22.0 2.00 .00 3.0 2.0 2.00 .69 03.300 0.0 206 49400 0 2 63 2 00 699 63 43 46.9
24 24.000 300 3,00 20 ¼ x ¾ 4 ¾ x 4 ¼ 24.00 2. 29.00 .00 36.00 32.00 29.0 .94 42.0600 60.0 206 6036 60 0 3 2 94 3 49 49 64.4
* Working Pressure and End Load are total, rom all internal and external loads, based on standard weight steel pipe, standard roll or cut grooved inaccordance with Victaulic speciications. Contact Victaulic or perormance on other pipe.
WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to ½ times the igures shown.
† Total bolts required to be supplied by installer, may be ordered rom Victaulic. Bolt sizes or conventional lange-to- lange connection. Longer boltsrequired when Vic-Flange utilized with waer-type valves.
§ Draw bolts supplied with 4 – 24”/30 – 600 mm Vic-Flange adapters.
# For cut groove systems only. For 4 – 24”/30 – 600 mm roll groove systems, AGS (Advanced Groove System) products are used. Style 4 is not compatiblewith the AGS system.
Shaded area o mating ace mustbe ree rom gouges, undulationsor deormities o any type oreective sealing.
06.06_5
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 6/8
DIMENSIONS
X
Z
Y W
Remove to mateto fat-aced
fanges.
AMax.
BMin.
Exaggerated for Clarity
STYLE 743
Grooved pipe adapter to
ANSI Class 300 flanges
SizeMax. WorkPressure *
Max. EndLoad * No. Bolts † Bolt/Nut Size †
Sealing SurfaceInches/mm Dimensions – Inches/mm
Approx.Wgt. Each
NominalSize
Inchesmm
ActualOutside
DiameterInchesmm
psikPa
Lbs.N Required Inches
“A”Maximum
“B”Minimum W X Y Z
Lbs.kg
2 2.3 20 3,90 5⁄8 x 3
2.3 3.4 .0 6.0 .00 0.93 4.0 60.3 4960 4200 60 96 6 2 24 2.2
2 ½ 2. 20 4,60 ¾ x 3 ¼
2. 3.9 .6 .0 . .06 .46 3.0 4960 200 3 99 29 9 49 2 3.4
3 3.00 20 6,92 ¾ x 3 ½
3.0 4.3 9.4 .2 6.63 . 9.0 .9 4960 30 9 24 20 6 30 4.
4 4.00 20 ,44 ¾ x 3 ¾
4.0 .3 .3 0.00 . .3 .300 4.3 4960 0930 4 4 2 24 200 33 6.9
.63 20 ,00 ¾ x 4 .6 6.2 2.3 .00 9.2 .43 .2 4.3 4960 4 33 29 23 36 .0
6 6.62 20 24,02 ¾ x 4 ½
6.63 . 3. 2.0 0.63 .0 23.40 6.3 4960 030 6 9 30 3 20 3 0.6
.62 20 42,042 7⁄8 x 4 ¾
.63 9.94 6.6 .00 3.00 .6 34.3200 29. 4960 00 29 22 424 3 330 43 .6
0 0.0 20 6,36 x ¼
0. 2.3 9.2 .0 .2 .93 4.320 23.0 4960 29060 23 33 49 44 3 49 2.9
2 2.0 20 9,06 1⁄8 x ¾
2. 4.3 22.2 20.0 . 2.06 0.300 323.9 4960 400 324 363 6 2 4 2 32.0
* Working Pressure and End Load are total, rom all internal and external loads, based on standard weight steel pipe, standard roll or cut grooved inaccordance with Victaulic speciications. Contact Victaulic or perormance on other pipe.
WARNING: FOR ONE TIME FIELD TEST ONLY, the Maximum Joint Working Pressure may be increased to ½ times the igures shown.
Style 43 Vic-Flange must be ordered as a actory assembly when connected to a Victaulic itting or valve. Contact Victaulic or details.
† Total bolts required to be supplied by installer, may be ordered rom Victaulic.
Shaded area o mating ace mustbe ree rom gouges, undulationsor deormities o any type oreective sealing.
06.06_6
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 7/8
1. The Style 741 (2 – 12"/50 – 300 mm) design incorporates small teeth inside the key shoulder
I.D. to prevent rotation. These teeth should be removed when Vic-Flange adapter is utilized with
a Victaulic Series 700 grooved end butterfly valve, Schedule 5 pipe or plastic pipe. Vic-Flange
adapter Style 741 may only be used on one side of Victaulic Series 700 butterfly valve, sizes
2 – 4"/50 – 100 mm fitted with standard or latch-lock handles.
2. Vic-Flange adapter must be assembled so it does not interfere with handle operation. Because of
the outside flange dimension, Vic-Flange adapter should not be used within 90° of one another on
a standard fitting. When wafer or lug-type valves are used adjoining a Victaulic fitting, check disc
dimensions to assure proper clearance.
3. Vic-Flange adapters should not be used as anchor points for tie-rods across nonrestrained joints.
Mating rubber faced flanges, valves, etc. requires the use of a Vic-Flange washer.
4. Area A-B noted in the above drawing must be free from gouges, undulations or deformities of any
type for effective sealing.
5. Vic-Flange adapter gaskets must always be assembled with the color coded lip on the pipe and
the other lip facing the mating flange.
6. Vic-Flange hinge points must be oriented approximately 90° to each other when mated.
7. Flange Washers: Vic-Flange adapters require a smooth hard surface at the mating flange face for
effective sealing. Some applications for which the Vic-Flange adapter is otherwise well suited do
not provide an adequate mating surface. In such cases, it is recommended that a metal (Type F
phenolic for Style 641 with copper systems) Flange Washer be inserted between the Vic-Flange
adapter and the mating flange to provide the necessary sealing surface.
Typical applications where a Flange Washer should be used are:
A. When mating to a serrated flange: a flange gasket should be used adjacent to the serrated
flange and then the Flange Washer is inserted between the Vic-Flange adapter and the f lange gas-
ket.
B.When mating to a wafer valve: where typical valves are rubber lined and partially rubber faced
(smooth or not), the Flange Washer is placed between the valve and the Vic-Flange adapter.
C. When mating a rubber faced flange: the Flange Washer is placed between the Vic-flanges and
the rubber faced flange.
D.When mating AWWA cast flanges to IPS flanges: the Flange Washer or Transition Ring is placed
between two Vic-Flange adapters with the hinge points oriented 90° to each other. If one flange
is not a Vic-Flange adapter (e.g., flanged valve), then a flange gasket must be placed adjacent to
that flange and the Flange Washer inserted between the flange gasket and the Vic-Flange adapter.
Transition rings rather than Flange Washers must be used when mating Style 741 to Style 341
Flange Adapters in sizes 14 – 24"/350 – 600 mm.
E. When mating to components (valves, strainers, etc.) where the component flange face has an
insert: follow the same arrangement as in Application 1.
When ordering Flange Washers, always specify product style (Style 741, 743, 341, 641, 994) and
size to assure proper Flange Washer is supplied.
VIC-FLANGE ADAPTER NOTES
06.06_7
Vic-Flange® AdaptersSTYLES 741 AND 743
06.06CARBON STEEL PIPE – GROOVED COUPLINGS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G
8/8/2019 741 Flange
http://slidepdf.com/reader/full/741-flange 8/8
WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details.
This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be
installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the
right to change product specifications, designs and standard equipment without notice and without
incurring obligations.
NOTE
GENERAL NOTES Style 741 and 743 Vic-Flange adapters provide rigid joints when used on pipe with standard roll or
cut groove dimensions and consequently allow no linear or angular movement at the joint.
Reference should always be made to the I-100 Victaulic Field Installation Handbook for the product
you are installing. Handbooks are included with each shipment of Victaulic products for complete
installation and assembly data, and are available in PDF format on our website at www.victaulic.com.
INSTALLATION
WCAS-6QAQRD
Vic-Flange® AdaptersSTYLES 741 AND 743
CARBON STEEL PIPE – GROOVED COUPLINGS
For complete contact information, visit www.victaulic.com
06.06 1534 REV G UPDATED 10/2006
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
06.06