722.7 Merc Filter VB Pos
description
Transcript of 722.7 Merc Filter VB Pos
-
AR27.19-P-0200GC Remove/install electrohydraulic control module (transmission installed) 27.10.97TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109TRANSMISSION 722.702 in MODEL 168.035 /135TRANSMISSION 722.750 /751 in MODEL 414.700
P27.19-2095-09
1 Transmission housing 5 Bolts 8 Oil filter2 Bolts 6 Oil pan 12 Electrohydraulic control unit3 Dowel pin 7 Gasket 14 Magnet4 Oil drain plugInstallation position of selector valve
10 Selector valve11 Transmission housing12 Electrohydraulic control unit
P27.19-0350-11
Page 1/3 Daimler AG, 7/28/09, G/06/09 / ar27.19-p-0200gc / Remove/install electrohydraulic control module (transmission installed)TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 ...
-
Location of screens and pressure holding valves in channel pattern
8 Strainer9 Pressure holding valve13 Screen cartridge
P27.35-2006-06
Modification notes
28.2.01 Transfer coding data for front wheel drive transmission Step 2 incorporated for the first timecontrol (FGS) to HHT- Win
28.2.01 Erase fault memory Step 14 incorporated for the first time28.2.01 Transfer stored coding data from HHT- Win to new front Step 11 revised.
wheel drive transmission control (FGS).27.7.01 Magnet in oil pan, newly included Step 7 newly included. BT27.40-P-0003-01A
Remove/Install
1 Move selector lever to position "P"2 Transfer coding data of the front
Only if the electrohydraulic control unit transmission control (FGS) to the STAR was replaced.DIAGNOSIS testerConnect STAR DIAGNOSIS and read out AD00.00-P-2000-04A
fault memoryDiagnosis system STAR DIAGNOSIS *WH58.30-Z-1048-13A
3 Unscrew oil drain plug (4) from oil pan and The torque converter has no oil drain
drain transmission oil plug.*BA27.10-P-1001-03A
If the transmission fluid is burnt or contains wear particles, the oil cooler lines and oil cooler must be flushed out:Flushing out oil cooler lines and oil cooler AR27.55-P-0001A
Installation: Install new sealing ring.4 Thoroughly clean area around oil pan
Risk of damage from dirt entering the transmission.
Use a lint-free cloth.5 Unscrew bolts (5). *BA27.10-P-1002-03A
6 Remove oil pan (6) with gasket (7) Replace gasket (7) if Installation: necessary. Ensure gasket is installed correctly (7).
Oil pan capacity modified Transmission 722.7 in model 168 BT27.10-P-0004-01A7 Remove magnet (14) from oil pan Model 168 as of approx. 07/2001
Model 4104.600/700 as of approx. 07/2001 Clean abrasion particles from magnet.
Magnet in oil pan, newly included
Transmission 722.7 in model 168 BT27.40-P-0003-01A8 Pull off oil filter (8)
Page 2/3 Daimler AG, 7/28/09, G/06/09 / ar27.19-p-0200gc / Remove/install electrohydraulic control module (transmission installed)TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 ...
-
9 Remove electrohydraulic control unit (12) by Installation: location of screen (8),
unscrewing bolts (2) observe pressure maintaining valves (9) and screen cartridge (13) in channel pattern.
Observe installation position Installation: of selector valve (10) of electrohydraulic control unit (12).
Installation: Ensure that the dowel pin (3) enters the bore of the transmission housing.
*BA27.35-P-1002-01A10 Install in the reverse order11 Transfer stored coding data from STAR
Only if the electrohydraulic control unit DIAGNOSIS tester to new front transmission was replaced.control (FGS)Connect STAR DIAGNOSIS and read out AD00.00-P-2000-04A
fault memoryDiagnosis system STAR DIAGNOSIS *WH58.30-Z-1048-13A
12 Inspect ATF level in automatic transmission, AR27.00-P-0101GCadd ATF if necessary
13 Perform adaptation of front transmission Only if the electrohydraulic control unit
control (FGS) with STAR DIAGNOSIS tester was replaced.Connect STAR DIAGNOSIS and read out AD00.00-P-2000-04A
fault memoryTransmission adaptation, front transmission AD27.19-P-2002-06GFcontrol
Diagnosis system STAR DIAGNOSIS *WH58.30-Z-1048-13A14 Erase fault memory
Automatic transmission oil pan
Number Designation Transmis-sion 722.3/4/5/7
BA27.10-P-1001-03A Oil drain plug on oil pan NM 22
BA27.10-P-1002-03A Bolt, oil pan to transmission housing NM 8
-
Shift valve housing
Number Designation Transmission 722.7
BA27.35-P-1002-01A Bolt, electrohydraulic control module NM 8to transmission housing
Commercially available tools
Number DesignationWH58.30-Z-1048-13A STAR DIAGNOSIS diagnosis system, Compact Passenger Car 6511 1801 00
Page 3/3 Daimler AG, 7/28/09, G/06/09 / ar27.19-p-0200gc / Remove/install electrohydraulic control module (transmission installed)TRANSMISSION 722.700 in MODEL 168.031 /032 /033 /131 /132 /133 TRANSMISSION 722.701 in MODEL 168.006 /007 /008 /009 /109 TRANSMISSION 722.702 in MODEL 168.035 /135 ...