64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2....

6
Seatbelt Solutions www.seatbeltsolutions.com 3-Point Conversion Seatbelt Installation Guide for: 1964 - 1975 General Motors Chevrolet Pontiac Oldsmobile Buick Chevelle LeMans Cutlass Skylark El Camino GTO Cutlass Supreme Sport Wagon Monte Carlo Firebird Century El Camino Apollo Nova Caprice Impala

Transcript of 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2....

Page 1: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

SeatbeltSolutions

www.seatbeltsolutions.com

3-Point Conversion Seatbelt Installation Guide for:

1964 - 1975 General Motors

Chevrolet Pontiac Oldsmobile BuickChevelle LeMans Cutlass SkylarkEl Camino GTO Cutlass Supreme Sport WagonMonte Carlo Firebird CenturyEl Camino ApolloNovaCapriceImpala

Page 2: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

Seatbelt Solutions

90 Degree Bracket 1 1/2” x 7/16”x20 Bolts 2.5” Flat Washer 1” x 7/16”x20 Bolts Stud Plate Bolts

7/16” Stud Plate Pop Rivets 1/2” x 13 Lock Nut Nylon Step Washer Nylon Washer

7/16”x20 Nylon Lock Nut CA53 Shoulder Plate 7/16” Bolt 7/16” Flat Washer Camaro Bracket

The hardware included in this kit has been designed to work with multiple years of General Motors vehicles.If your vehicle has existing anchor mounting points installed you may not need all of the provided hardware.

NOTE: This is an installation guide only, designed to aide you during the process of installingyour new seat belts. Some installations may not be covered therefore it will be the installers responsibilityto determine the safest mounting location.

Seatbelt Solutions, Inc, nor our vendors, bear any responsibility for improper installations by the end useror professional installer. We have designed this installation guide to be as informative and accurate aspossible, however some modifications or fabrication may be required for some vehicles. If you have anyQuestions or concerns we strongly suggest you contact a professional installation repair shop.

Seatbelt Solutions 2016

Page 3

Page 3: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

1. Remove old seatbelts. Clean any debris and rust out of threaded holes with a wire brush or thread chaser. If necessary, remove the front seats making sure to set the mounting bolts aside.

2. Most General motor vehicles after 1966 started to come with a shoulder belt or had the mounting holes installed. You will need to look behind the headliner to see if you have the factory shoulder belt mounting holes or if you will need to create a mounting point. The image to the left shows a factory installed mount with headliner removed.

3. If your vehicle has the mount as shown in the photo above you will use the hardware piece shown to the right along with the mounting bolts. You will need to carefully cut the headliner to provide access for the shoulder loop mounting bolt later in the installation.

4. If your vehicle does not have the factory mount for a shoulder belt you will need to find a strong steel support in the roof area or B pillar (if equipped) and use the CA53 flat plate along with the pop rivets provided to attach the plate. Always check the clearance between any support braces and the roof/exterior body panel before drilling. Make certain that you will not impact the roof/exterior panel causing damage to the panel or the exterior paint. Some vehicles that require mounting in the B pillar may also require a slot be created in the pillar to slide the CA53 plate into. You may also need to drill 3 holes for the pop rivets and mounting bolt. Use the plate as a template. You will need to carefully cut the headliner to provide access for the shoulder loop mounting bolt later in the installation.

1964-75 General Motors

Seatbelt Solutions 2016 Page 3

Page 4: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

1964-75 General Motors

5. After completing the shoulder belt mount portion of the installation you can decide the best location for the retractor. In most cases the retractor is too large to fit in the factory lap belt mounting location so you will need to install the retractor in the rear seat floor area as close to directly below the shoulder belt mount as you can. If the retractor is slightly forward or back of the shoulder mount you will be fine, just don’t mount it on a severe angle.

To mount the retractor, you will need to look under your vehicle in the area you which to install the mounting bracket to make sure there are no brake lines, fuel lines, wiring harnesses or interference with the frame. You will need a few inches of clearance to tighten the hardware under the car along with room to install the larger flat washer.

Carpet

Floor Pan

Once installed the blackAnchor should be Installedpointing towards the front ofthe vehicle.The photo showswhat the drivers side wouldlook like. You can alter theangle based on your seatcushion angle as needed.

The retractor, 5” black anchor and mounting bracketwill be assembled as shown below.

Seatbelt Solutions 2016 Page 4

Use Camaro bracketin place of 90 degreebracket for all 1967-75Camaro installations.

Page 5: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

1964-75 General Motors

6. Once the retractor is installed you can bolt the door post fitting (shoulder loop) into the ceiling or B pillar location you created in steps 3 or 4.

Seatbelt Solutions 2016 Page 5

DPF

Mounting Bolt

Nylon Spacer

Nut

Factory MountingDesign

Bolt 1” x 7/16” x 20

DPF

CA53Plate

Flat Washer

NylonSpacer

7. Now that the retractor is installed you can bolt in the buckles. If you have Factory mounting holes on the transmission tunnel than you should be able to bolt the new buckles in without using the 90 degree brackets provided with the hardware kit. If your car does not have mounting holes on the floor than you will need to determine the correct location for the buckles and follow the same procedure used for mounting the 90 degree bracket used on the retractor. Check under the car to make sure nothing is in the way first before drilling. Use the large flat washer under the car.

CA53 Plate forNon Factory mounting

Page 6: 64-75 Cover Page 1 - Seat belt CH… · front seats making sure to set the mounting bolts aside. 2. ... and use the CA53 flat plate along with the pop rivets provided to attach the

Warranty:

SEATBELT SOLUTIONS offers a one (1) year warranty on our products. The warranty coversdefects in materials and workmanship. If, during the warranty period, the product fails undernormal usage, because of a manufacturing defect, we will replace or repair the item after the unithas been returned to our facility for inspection and determination as to coverage.

Our warranty is limited to the retractor and buckle assembly only. The webbing material andassociated hardware are not covered under our warranty.

To obtain repair or replacement under the terms of this warranty, please contact us via phone ore-mail and request a return authorization number. A copy of the original purchase receipt isrequired.

Our warranty expires if the seatbelt has been involved in an accident therefore the seat beltsystem cannot be warranted, repaired, or returned.

Seatbelt Solutions, LLC15835 Corporate Road NJupiter, FL. 33478(561) 747-7165Email: [email protected]

Seatbelt Solutions July 2014 Page 6