5 Lifetime Extension for Siemens

8/6/2019 5 Lifetime Extension for Siemens

1/21

Lifetime Extension

forSIEMENS Gas Turbines

Authors:

Guido Lipiak

Susanne Bussmann

Co-Authors:

Christopher Steinwachs

Andreas Lttenberg

Power-Gen Europe 2006

30 May 1 June 2006, Cologne, Germany

VX 4.2 VX 4.3 VX 4.3A

Siemens AG 2006. All rights reserved.


2/21

Introduction

Table of Contents

1 Introduction ........................................................................................................3

2 Objectives of SIEMENS Lifetime Extension ..................................................................4

3 Why SIEMENS Lifetime Extension? .............................................................................5

4 The Maintenance Concept............................................................................................... 7

4.1 Maintenance Intervals .............................................................................................7

4.2 SIEMENS Lifetime Extension (LTE) ..................................................................... 9

5 The SIEMENS Lifetime Extension Program ................................................................10

5.1 Gas Turbine Frame-Specific LTE Analyses .........................................................10

5.2 Unit-Specific LTE Analyses .................................................................................14

5.3 Modernizations and Upgrades (MODs & UPs) ....................................................15

5.4 LTE Planning ........................................................................................................15

6 Implementation of SIEMENS Lifetime Extension Measures .......................................18

7 Summary ......................................................................................................20

Literature


2


3/21

Introduction

Lifetime Extension for SIEMENS Gas Turbines

Dipl.-Ing. Guido Lipiak, Siemens Power Generation, Gas Turbine Field Service

Engineering, Mlheim a.d. Ruhr/Germany

Susanne Bussmann, Student of Communication Science, University of Applied Sciences,

Gelsenkirchen/GermanyDipl.-Ing. Christopher Steinwachs, Siemens Power Generation, Gas Turbine Field Service

Engineering, Mlheim a.d. Ruhr /Germany

Dipl.-Ing. Andreas Lttenberg, Siemens Power Generation, Gas Turbine Field Service

Engineering, Mlheim a.d. Ruhr /Germany

1 Introduction

The worldwide demand for power grows faster than the world population. SIEMENS Power

Generation develops and builds combined cycle (gas and steam) power plants and power plant

components for all energy resources. SIEMENS gas turbines are renowned for their high

availability and reliability as well as high power output at low emissions.

With a lifetime expectancy of a combined cycle power station of 30 to 40 years, the gas tur-

bine by far exceeds the design lifetime. Essential components of the SIEMENS VX4.2,

VX4.3 and VX4.3A gas turbines - especially the components of the hot gas path and rotor

are designed for an operating time of 100,000 equivalent operating hours (EOH, for short) or

3,000 starts. Well founded and realistic lifetime concepts are required to keep the costs over

the entire lifetime to a minimum.


3Figure 1 SIEMENS Power Station Ambarli, Turkey, 6 x V94.2 (Source : Siemens PG)


4/21

Objectives of SIEMENS Lifetime Extension

To assure reliable and safe operation of the gas turbine even beyond the design lifetime of the

components, SIEMENS has developed the "Lifetime Extension" program (LTE program, for

short). Within the LTE program recommendations are made to the gas turbine operator; the

recommendations are developed based on the original design of gas turbine frames VX4.2,

VX4.3, VX4.3A, the Original Equipment Manufacturer (OEM) fleet operating experience and

the specific characteristics of the gas turbine, such as operating mode and unit history.

This paper will explain how SIEMENS arrives at the recommendations for lifetime extension

measures, and how these measures are subsequently planned and implemented.

2 Objectives of SIEMENS Lifetime Extension

The objective of the LTE program is to give the operators of SIEMENS VX4.2, VX4.3 and

VX4.3A gas turbines an opportunity to operate the gas turbine beyond the limited design life-

time of the gas turbine components. The LTE measures are to assure high availability, reli-

ability and safety for another lifetime of 100,000 EOH or 3,000 starts.

Figure 2 Trend of Siemens Gas Turbine Frames with Respect to EOH (Source: Siemens PG)

Siemens AG 2006. All rights reserved.4

The EOH a combination of fired hours and start/stop cycles and additional influencing fac-

tors like fuel composition or water/steam injection are only one criterion to estimate the life-


5/21

Why SIEMENS Lifetime Extension?

time consumption of the gas turbine components. Operated at base load, a gas turbine reaches

100,000 EOH after approximately 12 years.

A systematic and uniform course of action for cost-effective evaluation of the SIEMENS gas

turbines is required because the number of VX4.2, VX4.3, and VX4.3A machines that will

exceed 100,000 EOH in the near future increases steadily (refer to Figure 2).

The benefits of the measures derived from the SIEMENS Lifetime Extension by far outweigh

the relatively small expenditure for the LTE study.

Implementation of the LTE measures does not only significantly reduce the operating risk of

the unit, but also significantly decreases potential downtimes due to unscheduled outages or

additional maintenance activities. Significant portions of power and efficiency, which had ex-

perienced a reduction during the first 100,000 EOH due to wear and aging, can be regained.

The maintenance concept itself will not be modified; future maintenance costs can be pre-

dicted. The lower operating risk may also have a positive effect on the insurability of the ma-

chine.

3 Why SIEMENS Lifetime Extension?

The lifetime of SIEMENS gas turbines is limited, and primarily depends on the type of oper-

ating regime (base load, medium load or peak load), utilized fuel, firing temperature and am-

bient conditions. The gas turbine frame specific design of wear parts in the hot gas path as

well as maintenance intervals and quality play a key role.

Gas turbine components are exposed to stress caused by temperature or static and dynamic

loading like creep, low-cycle fatigue (LCF) and high-cycle fatigue (HCF), erosion, oxidation

and high temperature corrosion as well as mechanical stress and wear. The limitations for use-

ful service life are inthemajorityofcases based on the load capability of the components ex-

posed to the highest stress or temperatures. Each type of stress causes characteristic damage

which may occur individually or in a combination (refer to Figure 3).


The main components of SIEMENS gas turbines specifically the components of the hot gas

path and the rotor are designed for 100,000 EOH or 3,000 starts based on the stress they are

subjected to (refer to Table 1).
http://dict.leo.org/se?lp=ende&p=/Mn4k.&search=inhttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=thehttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=majorityhttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=ofhttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=caseshttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=caseshttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=ofhttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=majorityhttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=thehttp://dict.leo.org/se?lp=ende&p=/Mn4k.&search=in


6/21

Why SIEMENS Lifetime Extension?

Erosion &Contamination

Corrosion

Mechan. StressFatigueLow Cycle Fatigue

Corrosion &Oxidation

Creep

Figure 3 Examples of Effects Causing Aging in Turbines

Exceptions are components that are refurbished earlier during scheduled maintenance outages

or because they are considered wear parts (e.g. 1st stage blades or ceramic heat shields).


6

Table 1 Design Criteria and Life Expenditure Effects


7/21

The Maintenance Concept

4 The Maintenance Concept

Wear is the price paid for the use of a device or a unit. The objective of maintenance therefore

is not only to recognize the wear, but to influence it and create new reserves by repairing the

components or unit (refer to DIN 31 051). Reliable operation of the gas turbine is not feasible

without inspection and potentially re-establishing these wear reserves at inspections and major

overhauls. Inspections are performed to determine the condition of the machine and to define

condition-related corrections and repairs to protect the operator against unscheduled outages,

secondary damage, and loss of operation.

4.1 Maintenance Intervals

Gas turbine components are subjected to a series of inspections and maintenance inspections

at specified intervals:

Components deteriorate as a function of time and temperature (creep processes, corrosion and

oxidation) and also due to cyclic processes (high-cycle fatigue HCF, low-cycle fatigue LCF

and thermo-mechanic fatigue TMF). SIEMENS determines the inspection intervals of the

VX4.2, VX4.3 and VX4.3A gas turbines based on equivalent operating hours (EOH) of the

unit.

Maintenance inspection intervals are the basis for safe and disturbance-free unit operation.

SIEMENS gas turbines are subject to different maintenance intervals over the course of their


7

Figure 4 Maintenance Intervals of SIEMENS Gas Turbines


8/21


operating time. The intervals, i.e. time between inspections and major overhauls, depend on

the specified maintenance concept. The inspections are performed according to a Checklist.

Currently, there are two basic maintenance inspection concepts [2]:

MI = Minor Inspection

HGPI = Hot Gas Path Inspection

MO = Major Overhaul

LTE = Lifetime Extension Inspection

Minor Inspection (MI)

The minor inspection comprises the visual inspection of the accessible regions of the ma-

chine, the compressor and turbine inlet, the combustion chamber and the exhaust.

Optionally, non-accessible regions may be examined using borescopes.

The minor inspection includes the examination of various external gas turbine components.

Hot Gas Path Inspection (HGPI)

The turbine is opened for the hot gas path inspection. Based on the findings, the vanes and

blades of the turbine are inspected, refurbished or replaced based on the maintenance concept.

Various non-destructive examinations (NDE) are performed to determine the condition of the

essential components.


15 33

Figure 5 SIEMENS Maintenance Inspection Concepts


9/21


Major Overhaul (MO)

At a major overhaul, the compressor casing is removed and all compressor blades are in-

spected, as necessary and according to the checklist. The coated compressor front stages are

refurbished. The compressor guide vane carrier and the inlet casing are inspected as well.

Non-destructive examinations (NDE) and detailed visual inspections are performed, the rotor

is removed from the machine.

4.2 SIEMENS Lifetime Extension (LTE)

The maximum number of EOH reached by a gas turbine in the course of a calendar year es-

sentially depends on the number of starts and the service factor (fired hours) of the unit. Con-

sequently, the time at which a gas turbine should be subjected to an LTE analysis varies be-

tween 12 and 25 years.

The scope of the LTE inspection exceeds the scope of the major overhaul. The rotor must be

destacked in order to re-qualify the forged rotor components. New mechanized non-destruc-

tive examination (NDE) methods have been developed and qualified to detect critical defects


9

Figure 7 MO of SIEMENS VX4.3A Gas Turbines

Figure 6 HGPI of SIEMENS VX4.3A Gas Turbines


10/21

The SIEMENS Lifetime Extension Program

in the volume of service-stressed forgings. Potential LTE measures, for example, are addi-

tional visual and non-destructive examinations (NDE) like ultrasonic, eddy current and mag-

netic flux testing. Tailor-made recommendations for implementation of modifications and up-

graded products as well as condition based repair and replacement of components are imple-

mented in the course of the LTE inspection.

5 The SIEMENS Lifetime Extension Program

The SIEMENS LTE program allows evaluation of gas turbine components with respect to po-

tential remaining lifetime and is therefore the basis for subsequent LTE recommendations.

Unit-specific conditions and operator requests are taken into consideration as well. The

SIEMENS LTE program comprises the examination of each gas turbine frame and the unit-

specific analysis of the individual gas turbine.

At the same time,

recommendations for potential

modifications and upgrades

(MODs & UPs) are discussed,

specifically with respect to the

components that should be re-placed in the course of the

LTE measures. The gas turbine

operator subsequently has the

appropriate LTE measures

implemented by SIEMENS Field Service Personnel to extend the lifetime of the gas turbine

for another 100,000 EOH, or only for another interval.

5.1 Gas Turbine Frame-Specific LTE Analyses

SIEMENS implemented frame-specific LTE analyses for the individual gas turbine frames,

i.e. VX4.2, VX4.3 and VX4.3A, based on component design lifetime and the fleet operating

experience. Design-dependent recommendations for LTE measures applicable for the affected

components were determined in gas turbine frame specific LTE programs. As a result, LTE

Checklists for Lifetime Extension Inspections and LTE measures have been prepared in addi-

tion to the frame-specific Major Overhaul Checklists.


10

Figure 8 LTE on a V94.2 , Source Siemens PG


11/21


Within the scope of the frame-specific LTE analyses, all essential design groups of the three

gas turbine frames were examined and evaluated with respect to further operation of another

100,000 EOH or 3,000 Starts. This examination and evaluation took place in the course of the

Component Review and Component Analysis.

Component Review

Components for which further operation to 200,000 EOH is considered critical are determined

on the basis of their design and design data, and the SIEMENS gas turbine fleet operating ex-

perience.

Example of Component Review on a SIEMENS V94.2 Gas Turbine:

The Component Review of a SIEMENS V94.2 gas turbine starts with selecting the compo-

nents that are subject to lifetime limitation due to creep and LCF/HCF, corrosion/erosion, and

others, for example:


11

Figure 9 Selected Components at Component Review


12/21


The following decisions must be made for the selected components:

Component Analysis

The lifetime limitation of individual components is determined in the scope of the "Compo-

nent Analysis". Main components such as rotor disks and hollow shafts, compressor and tur-

bine vane carriers, casings and piping, but also compressors and turbine blades are analyzed

using different numerical and analytical methods, i.e. finite element method (FEM) and frac-

ture mechanics (FM), ASME Code and AD bulletins (refer to Figure 12).

The parts are analyzed with regard to static and dynamic loading as well as start and stop cy-

cles (steady state / transient). The component lifetime limitations were determined taking the

calculated variables, i.e. stress cycle number for crack initiation, crack growth and creep de-

formation, and the long-time fleet operating experience of the gas turbine frame into account.

Crucial factors for a meaningful component analysis are the basic design data and a consoli-

dated knowledge of boundary conditions like thermal convection and radiation, mechanical

restrains or contacts during the gas turbine operation. Selecting the appropriate analysis type

applying suitable and sufficient material data are preconditions for interpretation and valida-

tion of the computation results with the OEM fleet experience.

The determined component lifetime limitations and critical start numbers always apply for a

gas turbine frame (VX4.2/VX4.3/VX4.3A); they do not take individual deviations during op-


12

Figure 10 Component Review


13/21


eration or configuration of the unit into account. These gas turbine-specific values must be

determined by unit-specific LTE analyses.

Figure 11 Numerical Analysis of Turbine Rotor Disk and Turbine Exhaust Casing

Another result of the component analyses facilitated the definition of critical defect sizes as

well as location and orientation of critical defects in the component volume. This knowledge

in turn allowed the development of specific NDE processes, such as partially mechanized ul-

trasonic testing of the rotor wheel disks.

The partially mechanized ultrasonic test is used to check internal growth of material defects

caused by the forging process in the region of the wheel disk bores (refer to Figure 11).

It is possible to evaluate critical indications based on available calculation results. The

mechanized test technology and the digital acquisition of the ultrasonic test data allows com-

parison testing for potential deterioration of previous findings at any time. Recommendations

for specific repair measures or safe further operation of the affected component can be made.


13

Figure 12: Mechanized Ultrasonic Testing of Wheel Disk in Hub Area a) Mechanized Test System b) Test Probes and Setup


14/21


Other examples of NDE utilized in the course of the LTE are manual ultrasonic inspection of

all forged turbine components and dye penetrant inspection of the casings. Surface crack de-

tection by magnetic flux inspection will also be used on a number of components. Geometri-

cal measurements, wall thickness measurements and length measurements of components are

enhancing the measures for lifetime extension.

5.2 Unit-Specific LTE Analyses

Unit-specific analyses allow detailed evaluation of each gas turbine. This means, all influental

factors relating to operation and state are gathered on each gas turbine and taken into account

in the analyses. Aspects with respect to history as well as previous and future operating mode

of the gas turbine must be taken into consideration; the data are compiled and documented

using a questionnaire.

Unit history

The history of the gas turbine plays an important role in the unit-specific evaluation. Of spe-

cial importance are what inspections were already performed and what the results were, and

which components have already been replaced or repaired. Already known damage on the

unit must be disclosed.

Operating Mode

Also included in the evaluation of the lifetime limitation must be the way the machine was

operated in the past, how it is operated now, and how it is supposed to be operated in the

future. A differentiation is made between base load, intermediate load and peak load.

The power plant owner decides whether the gas turbine is to be operated for another 100,000

EOH or only for the next maintenance interval. Decisive in the evaluation of the lifetime are

also the extent of fast loading, the utilized fuel and firing temperature and the use of water or

steam injection.

The results of the gas turbine frame-specific and unit-specific analyses yield the unit-specific

LTE recommendations for lifetime extension measures.


14


15/21


5.3 Modernizations and Upgrades (MODs & UPs)

"MODs & UPs" are modernization and upgrade measures that contribute to improved power

or efficiency, lower emissions or longer component lifetime or inspection intervals of the gas

turbine. The improvement options are investigated in the scope of the unit-specific and frame-

specific analyses. These options may be selected by the gas turbine operator when the

SIEMENS LTE measures are due instead of replacing worn components. SIEMENS, the

Original Equipment Manufacturer (OEM), has developed and is continuing to develop a

number of modernizations and upgrade packages to keep up with the requirements of utilities

to increase output and efficiency, decrease maintenance cost, increase reliability and robust-

ness of the systems as well as availability, and starting reliability. The implementation of

these upgrade measures within the extended LTE work scope does not only improve the spe-

cific key performance requirements of the owner but also reduces the cost for intermediate-

term operation.

Examples of these modernizations and upgrades are concepts for increased compressor mass

flow, upgrade packages to extend major overhaul intervals of specific hot gas path compo-

nents, emission reduction packages, e.g. improved low NOx burners and improved NOx con-

trol, as well as packages for frequent startup operation or increased firing temperatures, wet

compression or evaporation cooling for power augmentation, upgrades to minimize compres-

sor efficiency losses utilizing improved compressor coating and advanced compressor clean-

ing methods. [3]

5.4 LTE Planning

The time-consuming planning of LTE ideally begins in the course of preparing for the last

major overhaul or hot gas path inspection before 100,000 EOH are reached (refer to Figure

13).

With this approach, pre-Investigations for LTE for premature wear on strategic components

can already be performed at the last MO or HGPI ahead of the intended LTE inspection.


15


16/21


Figure 13 The Date of Planning LTE

It also provides an opportunity to take samples and perform material analyses with respect to

creep rupture strength, low-cycle fatigue, or metallographic analyses of microsections. This

applies, for example, for taking samples from the inner casing and mixing casing on VX4.2

gas turbines.

Consequently, the results of microstructural analyses of stage 3 and stage 4 turbine blades per-

formed in the course of the HGPI after 75,000 EOH will make it easier to estimate the poten-

tial remaining lifetime when another analysis is performed on the blades which had remainedin operation until 100,000 EOH, for LTE purposes.

If the gas turbine operator requests a quote for LTE measures, SIEMENS Service Market-

ing/Sales and SIEMENS Service Engineering will perform the LTE analyses jointly (refer to

Figure 14).


16

Based on the preceding analyses, a unit-specific recommendation is made with respect to fu-

ture gas turbine operation, component life extension, repair, or replacement of the compo-


17/21


nents. These LTE recommendations are presented to the operator in the form of a bid. The

measures are subsequently implemented by SIEMENS Field Service Personnel.

All results are appropriately documented in the course of LTE planning and implementation.

To assure on-time delivery of replacement parts, the need of required strategic replacement

parts is discussed already after initial operator discussions, and delivery dates are coordinated

between Manufacturing and Marketing/Sales. The advantage of early LTE planning and early


17

Figure 14 The Workflow of Planning SIEMENS Lifetime Extension


18/21

Implementation of SIEMENS Lifetime Extension Measures

ordering thereby is ruling out logistic problems, and assuring smooth execution of the mainte-

nance measures.

The close working relationship between the plant operator and SIEMENS Service Market-

ing/Sales, SIEMENS Field Service Engineering and SIEMENS Field Service Personnel as-

sures that the appropriate analyses are performed on the individual machines and that the life-

extending measures are implemented optimally. Effective project management is required on

both sides, i.e. manufacturer's side and customer's side.

6 Implementation of SIEMENS Lifetime Extension Measures

Approaching 100,000 EOH, a series of steps must be taken in preparation of lifetime exten-

sion measures. The information gained from gas turbine frame-specific experience and cal-

culation results as well as unit-specific analyses are the basis for developing SIEMENS LTE

measures.

The first step of implementing the entire SIEMENS Lifetime Extension measures is to contact

the plant operator based on the results of the planned outage prior to the 100,000 EOH to in-form him of the LTE concept and the associated implications to assure that he is aware of the

program.

Secondly, the history and operating mode of the gas turbine will be investigated via a ques-

tionnaire. Based on the input as well as fleet investigations and recalculations for certain

components, a tailor-made concept will be presented to the specific operator.

Thirdly, depending on the preparation time for the lifetime extension and the time schedule of

the operator, a minor inspection ahead of the LTE inspection will be used for a number of ad-

ditional investigations in preparation of the unit-specific LTE.

Finally, depending on operators intention to use the plant short-term or over decades, the

scope of work, including modernization and upgrade measures, will be defined.

All LTE measures are performed in addition to the scope of a normal major overhaul.


18


19/21

Implementation of SIEMENS Lifetime Extension Measures

Examples of LTE Measures Implemented on a SIEMENS V94.2 Gas Turbine:

Component Potential Test Methods Findings Measures

1 Compressor BladesMagnetic Particle Test/

Eddy Current Test

Corrosion and

CracksReplacement


19

Figure 15 Examples of LTE Measures Implemented on a Siemens V94.2 Gas Turbine

7 8

65321 4

9


20/21

Summary

Component Potential Test Methods Findings Measures

2 Compressor Vanes Ultrasonic TestCracks on

HooksReplacement

3 Flame Tube/Tile

HoldersStandard per LTE Program Wear

Replacement per

LTE Program

4 Burner NDE / Visual InspectionCorrosion/

CracksReplacement

5 Seal Ring Visual Inspection Wear Replacement

6 Casing Dye Penetrant Test Cracks Repair

7 Turbine BladesSample Taking/

Metallurgical Analyses

Cracks/

Degradation

Live Extension for

one further

interval

8 Inner CasingSample Taking /Metallurgical Analyses

OxidationRepair and lifeextension for one

further interval

9 Rotor DiskMechanized Ultrasonic

TestingNo Findings

Re-qualification

and life extension

for 100.000 EOH

Table 2 Examples of Methods, Findings and LTE Measures on Components

7 Summary

The SIEMENS LTE program provides gas turbine-specific recommendations for LTE meas-

ures based on gas turbine frame-specific analyses taking unit-specific analyses, machine his-

tory and findings into account. Besides SIEMENS LTE measures, modernization and upgrade

options are offered to allow the operator to replace components.


20

This approach provides a low risk, reliable and significant advantage to the plant operator.

There is also a clear advantage with respect to estimated life cycle cost as well as reliability

and availability of the plant; the lower operating risk alone may have a positive effect on the

insurability of the power plant.


21/21

Summary

The SIEMENS LTE Program is crucial for reliable and safe operation of the SIEMENS gas

turbines for another 100,000 EOH or 3,000 starts, thereby assuring business success to the op-

erators of SIEMENS gas turbines beyond the original design lifetime.

Literature

[1] Wrede, U.; Bohrenkmper, G.; Umlauft, R.: Lebensdauerverlngernde Manahmen an

Gasturbinen; Allianz Report 2/99.

[2] Deblon, B.; Bohrenkmper, G.: Rehabilitation and retrofitting of heavy-duty gas turbine;

Power-Gen Europe Conf., Madrid (Spanien) 17.-19.Juni 1997.

[3] Dibbert, Andreas: Neue Power fr Gasturbinen; Energiespektrum 10/2005

Biographical Information

Speaker: Guido Lipiak

Company: Siemens Power Generation

Country: Germany

Guido Lipiak is Manager of the Mature Frame Team in Gas Turbine Field Service Engineer-

ing Mlheim, Germany. He earned his degree in mechanical engineering at the University of

Duisburg, Germany. In 1995 he joined Siemens KWU and initially worked for the gas turbine

blade technology and materials engineering departments. For damage clarification and root

cause analysis, he started working as a Fact Finding Engineer in 1996 and became Project

Manager in the Mlheim Gas Turbine Service Department in 1999 where he initiated the

SIEMENS Lifetime Extension Program in 2001.

21

Since 2005 Mr. Lipiak has been team manager of the Mature Frame Team for the VX4.2 and

VX4.3 Gas Turbines in Field Service Engineering. He is an expert for the fleet operating ex-

perience of the SIEMENS V64.3 Gas Turbine.

5 Lifetime Extension for Siemens

Documents

Transcript of 5 Lifetime Extension for Siemens