4ST - Self-Priming Trash Pump - Cornell Pump Company · 2015. 8. 7. · SELF PRIMING TRASH PUMP 4ST...
2
Size 4” x 4” Capacities To 800 GPM Total Dynamic Heads 130 Ft. Solids Handling 3” Dia Repriming Lifts To 25 Ft. Flanges 4” NPT or ANSI 125lb Impeller Semi-open, 2 Vane Trash Handling Approx. Weight 595lbs Bearing Housing Separate oil reservoir w/ dual bearing protection Mounting Options Pedestal Frame Mount, Engine Mount (SAE #4), Base Mount PRODUCT CAPABILITIES MATERIALS OF CONSTRUCTION SELF PRIMING TRASH PUMP 4ST *optional Other material options available Shimless impeller clearance adjustment Easily removable coverplate Back pullout rotating assembly Dual protection of bearings Atmospheric barrier and dual lip seals Volute passes full solid size Exclusive rubber lined dual wear plates Easily replaceable suction check valve Heavy duty bearings Heavy duty castings Solids handling impeller Self aligning Silicon-Carbide seal w/ oil lubrication Rapid Self-Priming No need for discharge check valve Optional casing heater ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Materials All Iron w/ Ductile Iron Volute & Impeller or Hard Iron Fitted* or 316SS Fitted* Shaft 4130HT Steel or Duplex Stainless Steel* Bearings Pump End: Ball Bearing Drive End: Dual Ball Bearing Wear Plates Oil resistant, rubber coated or Stainless Steel* or Hardened Iron* Gaskets Buna or Viton* Pressure Relief Valve Brass Suction Check Valve Canvas Reinforced Nitrile Rubber or Viton* Mechanical Seal Self aligning Silicon-Carbide Seal w. oil lubrication Jansen Pompentechniek T: +31(0)485-371318 E: [email protected]
Transcript of 4ST - Self-Priming Trash Pump - Cornell Pump Company · 2015. 8. 7. · SELF PRIMING TRASH PUMP 4ST...
Size 4” x 4”Capacities To 800 GPMTotal Dynamic Heads 130 Ft.Solids Handling 3” DiaRepriming Lifts To 25 Ft.Flanges 4” NPT
or ANSI 125lbImpeller Semi-open, 2 Vane
Trash HandlingApprox. Weight 595lbsBearing Housing Separate oil reservoir w/ dual
bearing protectionMounting Options Pedestal Frame Mount, Engine
Mount (SAE #4), Base Mount
PRODUCT CAPABILITIES
MATERIALS OF CONSTRUCTION
SELF PRIMING TRASH PUMP
4ST
*optionalOther material options available
Shimless impeller clearance adjustmentEasily removable coverplateBack pullout rotating assemblyDual protection of bearingsAtmospheric barrier and dual lip sealsVolute passes full solid sizeExclusive rubber lined dual wear platesEasily replaceable suction check valveHeavy duty bearingsHeavy duty castingsSolids handling impellerSelf aligning Silicon-Carbide seal w/ oil lubricationRapid Self-PrimingNo need for discharge check valveOptional casing heater
✔✔✔✔✔✔✔✔✔✔✔✔
✔✔✔
Materials All Iron w/ Ductile IronVolute & Impelleror Hard Iron Fitted*or 316SS Fitted*
Shaft 4130HT Steel or Duplex Stainless Steel*
Bearings Pump End: Ball BearingDrive End: Dual Ball Bearing
Wear Plates Oil resistant, rubber coatedor Stainless Steel*or Hardened Iron*
Gaskets Buna or Viton*Pressure Relief Valve BrassSuction Check Valve Canvas Reinforced
Nitrile Rubber or Viton*Mechanical Seal Self aligning Silicon-Carbide
Seal w. oil lubrication
Jansen Pompentechniek T: +31(0)485-371318 E: [email protected]
geert
Draft
4ST SELF PRIMING TRASH PUMP
2.76
9.00 9.00
19.51
5.8711.00
.98
8.94
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" 150# R.F. FLANGES OPTIONAL
4" NPT DISCHARGECONNECTION
30.49
HOLE
4 x .55 DIA.
4" NPT SUCTIONCONNECTION
19.49
TYP.2.36
.79
6.26
19.69
8.74
19.69
KEYWAY.38 x .19
5.00
12.99
1.50
7/28/10
SW10683DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10683
GH 7/28/10 TO SCALE4ST-F (THREADED)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
9.00 9.00
2.7619.51
9.4311.00
.98
12.50
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" NPT CONNECTION OPTIONAL
19.69
8.74
19.69
4" 150# R.F.DISCHARGEFLANGE
32.01
4 x .55 DIA.HOLE
4" 150# R.F.SUCTIONFLANGE
19.49
2.36TYP.
.79
9.76
KEYWAY.38 x .19
5.00
12.99
1.50
7/29/10
SW10684DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10684
GH 7/29/10 TO SCALE4ST-F (FLANGE)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
2.76
9.00 9.00
19.51
5.8711.00
.98
8.94
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" 150# R.F. FLANGES OPTIONAL
4" NPT DISCHARGECONNECTION
30.49
HOLE
4 x .55 DIA.
4" NPT SUCTIONCONNECTION
19.49
TYP.2.36
.79
6.26
19.69
8.74
19.69
KEYWAY.38 x .19
5.00
12.99
1.50
7/28/10
SW10683DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10683
GH 7/28/10 TO SCALE4ST-F (THREADED)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
9.00 9.00
2.7619.51
9.4311.00
.98
12.50
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" NPT CONNECTION OPTIONAL
19.69
8.74
19.69
4" 150# R.F.DISCHARGEFLANGE
32.01
4 x .55 DIA.HOLE
4" 150# R.F.SUCTIONFLANGE
19.49
2.36TYP.
.79
9.76
KEYWAY.38 x .19
5.00
12.99
1.50
7/29/10
SW10684DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10684
GH 7/29/10 TO SCALE4ST-F (FLANGE)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
19.51
5.8711.00
.98
8.94 2.76
9.00 9.00
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" 150# R.F. FLANGES OPTIONAL
KEYWAY.38 x .19
12.99
1.50
25.94
CONNECTION4" NPT DISCHARGE
SAE#4
30.49
HOLE
4 x .55 DIA.
4" NPT SUCTIONCONNECTION
19.49
TYP.2.36
.79
6.26
19.69
8.74
19.69
9/28/10
SW10690DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10690
GH 7/30/10 TO SCALE4ST-EM-4 (THREADED)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
9.00 9.00
19.51
9.4311.00
.98
12.50 2.76
NOTE:1. OVERALL DIMENSION MAY VARY ± .122. 4" NPT CONNECTION OPTIONAL
9/28/10
SW10691DWG. NO.
JOB NO.
PATT. NO.
CHECKED SCALEDATEDR.
REV. NO. DESCRIPTION DATE BY
SW10691
GH 7/30/10 TO SCALE4ST-EM-4 (FLANGE)CORNELL
R CORNELL PUMP COMPANY PORTLAND, OREGON
FLANGE
4" 150# R.F.DISCHARGE
SAE#4
32.01
19.69
8.74
19.69
KEYWAY.38 x .19
12.99
1.50
29.51
4 x .55 DIA.HOLE
4" 150# R.F.SUCTIONFLANGE
19.49
2.36TYP.
.79
9.76
4ST-F Threaded
4ST-F Threaded 4ST-EM Threaded
4ST-EM Flange
4ST-F Flange
4ST-F Flange
Other mounting configurations available
Jansen Pompentechniek T: +31(0)485-371318 E: [email protected]
