48FC 04-07 WEATHERMAKER SERIES WITH ECOBLUE™ …
Transcript of 48FC 04-07 WEATHERMAKER SERIES WITH ECOBLUE™ …
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Printed in U.S.A. Form 48FC-4-7-02SB Pg 1 3-19 Replaces: 48FC-4-7-01SB
48FC 04-07 WEATHERMAKER® SERIESWITH ECOBLUE™ TECHNOLOGY
SINGLE PACKAGE ROOFTOPGAS HEAT/ELECTRIC COOLING UNITS
— PERFORMANCE DATA
— CERTIFIED DIMENSION PRINTS
— CERTIFIED ROOF CURB DETAILS
2
JOB NAME: LOCATION:
BUYER: BUYER PO #: CARRIER#:
UNIT NUMBER: MODEL NUMBER:
PERFORMANCE DATA CERTIFIED BY:
DESCRIPTION48FC units are single-packaged electric cooling, gas heating unit that are pre-wired and pre-charged with Puron® (R-410A) HFCrefrigerant. The units are factory tested in both heating and cooling modes. Sizes 04-06 models use single-stage cooling capacitycontrol. Size 07 models use two-stage cooling capacity control.
FEATURES
Standard Base Unit• Puron (R-410A) HFC refrigerant• SEER of 14.0 (3 to 5 Ton)• IEER of 15.0• Meets or exceeds ASHRAE 90.1 energy efficiency levels• Rated in accordance with AHRI Standards 210/240 for
sizes 04 to 06 and 340/360 for size 07• Designed in accordance with Underwriters Laboratories
Std 1995• Listed by UL and UL-Canada• Single-stage cooling capacity control on 04 to 06 models,
two-stage on 07 models • Corrosive resistant composite sloping design; side or cen-
ter drain condensate pan. Meets ASHRAE Standard 62• Standard cooling operating range from 40°F up to 115°F
(4°C up to 46°C). Field installable accessory extends theminimum down to –20°F (–29°C)
• Field convertible from vertical to horizontal airflow forslab mounting — no special kits required
• Two-inch disposable return air filters• Thru-the-bottom power and gas entry capability• Single point gas and electric connections• 24-volt control circuit protected with resettable circuit
breaker• Direct Drive - EcoBlue™ technology indoor fan system
uses vane axial fan design and electronically commutatedmotor– Shall have inherent automatic-reset thermal overload
protection– Shall require no fan/motor belts for operation, adjust-
ments, and/or initial fan speed setup– Shall be internally protected from electrical phase rever-
sal and loss– Shall have slow ramp up to speed control capabilities to
help reduce sound and comfort issues– Shall be a slide-out design with two screw removal– On 07 size model with two stage cooling capacity con-
trol, the indoor fan speed is automatically controlled tomeet the code compliant 66% low fan speed and 100%at full fan speed
• Totally enclosed condenser motors with permanently lubri-cated bearings
• Low-pressure and high-pressure switches• Full perimeter base rail with built-in rigging adapters and
fork truck slots• Centralized terminal board facilitating simple safety circuit
troubleshooting and simplified control box arrangement• New unit control board with intuitive quick fan speed
adjustment
Cabinet• Access panels with easy grip handles• Innovative, easy starting, no-strip screw feature on unit
access panels• Pre-painted exterior panels and primer-coated interior pan-
els tested to 500 hours salt spray protection• Fully insulated cabinet• Tool-less filter access doorRefrigerant System• Acutrol™ refrigerant metering system on 04 to 06 models,
TXV on 07 models• Liquid line filter drier• Scroll compressors with internal line-break overload
protection (one-stage on 04 to 06 models, two-stage on07 models)
• Copper tube, aluminum fin coils with optional corrosionresistant coils
• Top cover removable gage line plugs for reading refriger-ant pressure with unit panels in place
Gas Heat• IGC solid-state gas heat exchanger control for on-board
diagnostics, anti-cycle protection, LED error code designa-tion, burner control logic and energy saving indoor fanmotor delay
• Gas efficiencies up to 81%• Inducted draft combustion• Redundant gas valve, with 2 stages of heating• Flame roll-out safety protector• Solid-state electronic direct spark ignition system• Dedicated 3 to 5 ton “low NOx” models available that
meet California Air Quality Management NOx require-ment of 40 nanograms/joule. Low NOx models includestainless steel heat exchangers.
Standard Limited Parts Warranty• 15-year gas heat exchanger parts - Stainless Steel• 10-year gas heat exchanger parts - Aluminized• 5-year compressor parts• 5-year factory installed Ultra Low Leak Economizer• 3-year SystemVu™ controls• 1-year parts
3
PERFORMANCE DATAUnit Operating Weight __________________________ lb
COOLING
Gross Total Capacity __________________________ Btuh
at Condenser Air Temperature __________________ °F
Gross Sensible Capacity _______________________ Btuh
Compressor Power Input _______________________ kW
Indoor Entering: db __________ °F / wb __________ °F
Airflow _____ CFM External Static Pressure _____ in. wg
Indoor Fan Motor Size __________________________ HP
Indoor Fan Motor Setting ______________________ Vdc
Exhaust Fan Motor Size ________________________ HP
Curb Weight __________________________________ lb
HEATING (GAS)
Heating Capacity:
Stage 1 ____________________________________ Btuh
Stage 2 ____________________________________ Btuh
Heating Capacity Total _______________________ Btuh
Stage 1 ____________________________________ kW
Stage 2 ____________________________________ kW
Heating Capacity Total _______________________ kW
ELECTRICAL DATA
Power Supply to Unit ____________________________________
Volts _________________________________________________
Phase _________________________________________________ Hz
Maximum Circuit Amps __________________________________
Maximum Overcurrent Protection __________________________
SUBMITTAL DATA
Job Name _____________________________________________
Architect ______________________________________________
Engineer _____________________________________________
Contractor _____________________________________________
Unit Designation ________________________________________
®
®
®
®
4
FACTORY-INSTALLED OPTIONS
Economizer with DRY BULB Sensing and Baro-metric Relief (04-06 sizes)Low Leak Air Dampers —
Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and Baro-metric Relief (04-06 sizes)Low Leak Air Dampers —
Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er 2 system).
Economizer with DRY BULB Sensing and Baro-metric Relief (04-07 sizes)ULTRA LOW LEAK Air Dampers —
Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 prescriptivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er X system).
Models with RTU Open and SystemVu meetCalifornia Energy Commission Title 24-2016prescriptive section 140.4 (damper leakage,etc.) and mandatory section 120.2.i for FaultDetection and Diagnostic requirements. Econo-mizers meet ASHRAE 90.1-2016 damper leak-age requirements as stated in section 6.5.1.1.4and Table 6.4.3.4.3, and meet 2016 Fault De-tection and Diagnosis requirements in section6.4.3.12. Economizers meet IECC 2012 sectionC402.4.5.2 and IECC 2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, andrelief air damper leakage requirements andIECC 2015 section C403.2.4.7 for Fault Detec-tion and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and Baro-metric Relief (04-07 sizes)ULTRA LOW LEAK Air Dampers —
Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 prescriptivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er X system).Models with RTU Open and SystemVu meetCalifornia Energy Commission Title 24-2016prescriptive section 140.4 (damper leakage,etc.) and mandatory section 120.2.i for FaultDetection and Diagnostic requirements. Econo-mizers meet ASHRAE 90.1-2016 damper leak-age requirements as stated in section 6.5.1.1.4and Table 6.4.3.4.3, and meet 2016 Fault De-tection and Diagnosis requirements in section6.4.3.12. Economizers meet IECC 2012 sectionC402.4.5.2 and IECC 2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, andrelief air damper leakage requirements andIECC 2015 section C403.2.4.7 for Fault Detec-tion and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).
5
FACTORY-INSTALLED OPTIONS (CONT)
Standard Base Unit SystemVu™ controls that include:
• Large full text - multi-line display
• USB flash port for data transfer
• Built in i-Vu®, CCN, and BACnet
• Refrigerant pressure from display
• Quick LED status — Run, Alert, Fault
• Conventional slat or sensor capabilities
• Historical component runtime and starts
• Supply air tempering
• Equipment Touch™ / System Touch™compatibility
• Demand limiting and ZS sensor compatibility
RTU Open multi-protocol controller communicatesto BACnet*, Modbus†, LonWorks**, and JohnsonN2 protocols.
Through the base connectors for gas and electricconduit/piping
Stainless steel gas heat exchanger (includes tubes,vestibule plate and collector box)
Humidi-MiZer® adaptive dehumidification system(This option should also include low ambientcontrols)
Two-position motorized outdoor air damper (04-06 sizes)
Non-fused disconnect
Powered 115-volt convenience outlet
Non-powered 115-volt convenience outlet
High static evaporator fan motor
Return air smoke detector
Supply air smoke detector
CO2 sensor
Condenser hail guard - louvered style
Special coating protection for evaporator and con-denser coils
Hinged access doors
Condensate overflow switch
MERV-8 return air filters
Phase Monitor Protection (3-Phase models only)
Optional Warranties Complete unit parts only, up to 5 years
Complete unit parts and labor, up to 5 years
Many other optional warranties are available. Seethe Commercial Start-Up and Optional ExtendedWarranty Price pages for further information.
* BACnet is a registered trademark of ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers).† Modbus is a registered trademark of Schneider Electric.** LonWorks is a registered trademark of Echelon Corporation.
6
FIELD-INSTALLED ACCESSORIESNOTE: 48FC 07 models use two-speed indoor fan logic, the W7212 controller is designed for single-speed motor control.
See Application Tip “ROOFTOP-18-01” for further guidance when using this unit.
Economizer with DRY BULB Sensing and Baro-metric ReliefLow Leak Air Dampers —
Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er® IV system).Models with W7220 controller meet CaliforniaTitle 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and Baro-metric ReliefLow Leak Air Dampers —
Models with W7212 controller provide standardnon-diagnostic control (EconoMi$er IV system.)Models with W7220 controller meet CaliforniaTitle 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er X system).Models with RTU Open controller meet Califor-nia Title 24 (Section 120.2), IECC, and ASHRAE90.1 for Fault Detection and Diagnostic (FDD) re-quirements (EconoMi$er 2 system).
Economizer with DRY BULB Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —
Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 prescriptivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated.Models with RTU Open meet California EnergyCommission Title 24-2016 prescriptive section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2013 / 2016 damper leakage re-quirements as stated in section 6.5.1.1.4 and Ta-ble 6.4.3.4.3, and meet 2016 Fault Detection
and Diagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and IECC 2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, andrelief air damper leakage requirements andIECC 2015 section C403.2.4.7 for Fault Detec-tion and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).
Economizer with ENTHALPY Sensing and Baro-metric ReliefULTRA LOW LEAK Air Dampers —
Models with W7220 controller meet CaliforniaEnergy Commission Title 24-2016 prescriptivesection 140.4 (damper leakage, etc.), and man-datory section 120.2.i for Fault Detection andDiagnostic controls. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12. Foroutside air, return, and relief air damper leakagerequirements economizers meet IECC 2012section C402.4.5.2 and IECC 2015 sectionsC403.2.4.3 and C403.3.3.5 and IECC 2015 sec-tion C403.2.4.7 for Fault Detection and Diag-nostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated.Models with RTU Open meet California EnergyCommission Title 24-2016 prescriptive section140.4 (damper leakage, etc.) and mandatorysection 120.2.i for Fault Detection and Diag-nostic requirements. Economizers meetASHRAE 90.1-2016 damper leakage require-ments as stated in section 6.5.1.1.4 and Table6.4.3.4.3, and meet 2016 Fault Detection andDiagnosis requirements in section 6.4.3.12.Economizers meet IECC 2012 sectionC402.4.5.2 and IECC 2015 sections C403.2.4.3and C403.3.3.5 for outside air, return air, andrelief air damper leakage requirements andIECC 2015 section C403.2.4.7 for Fault Detec-tion and Diagnostic requirements. NOTE: IECC 2015 section C403.2.4.7.1 re-quires differential return air sensor, which mustbe ordered separately.Outside air, return air, and relief air (volume)dampers are AMCA rated — plus 5 year limitedparts warranty (EconoMi$er 2 system).
7
FIELD-INSTALLED ACCESSORIES (CONT)NOTE: 48FC 07 models use two-speed indoor fan logic, the two-position damper and manual dampers are designed for single-
speed motor control. See Application Tip “ROOFTOP-18-01” for further guidance when using this unit.
Power exhaust — prop fan design
Two-position motorized outdoor air damper
Manual outside air damper 25%
Manual outside air damper 50%
Roof curb — 14 inch (356mm) tall
Roof curb — 24 inch (610mm) tall
Thru-the-bottom connections, electrical only
Thru-the-bottom connections, electrical and gas
Condenser hail guard, louvered style
Flue shield
Flue discharge deflector
Liquid propane (LP) conversion kit
High altitude conversion kit
Phase monitor (loss of phase/phase reversal)
Winter start kit, down to 25°F (–4°C)
Fan/Filter status switch
Low ambient head pressure controller, down to0°F (–18°C)
Low ambient head pressure controller, down to–20°F (–29°C)
Time Guard II compressor anti-cycle protection
Thermostats and sensorsNOTE: Size 07 model has two-stage cooling thermostat; use appropriate thermostat.
Condensate overflow switch
Non-powered 115-volt (20 amp) convenience outlet
Side access hinged filter door kit
Horn/Strobe annunciator
Economizer Sensors
Single dry bulb control
Differential dry bulb control
Single enthalpy control
Differential enthalpy control
CO2 — wall mounted
CO2 — duct mounted
CO2 — unit mounted
8
CE
RT
IFIE
D D
IME
NS
ION
PR
INT
Fig
. 1 —
48F
C**
04-0
7 D
imen
sio
nal
Dra
win
g
9
CE
RTI
FIE
D D
IME
NS
ION
S P
RIN
T
Fig
. 1 —
48F
C**
04-0
7 D
imen
sio
nal
Dra
win
g (
con
t)
10
CE
RT
IFIE
D D
IME
NS
ION
PR
INT
Fig
. 1 —
48F
C**
04-0
7 D
imen
sio
nal
Dra
win
g (
con
t)
11
EE
7/16
"[1
1]
4 9/
16"
[115
.5]
1/4"
[7.0
]
5' 7
-3/8
"[1
711.
3]
1' 4
-13/
16"
[4
27] I
NSI
DE
1-3/
4"[4
4.4]
2-3/
8"[6
1]
1-3/
4"[4
4.5]
1.00
"[2
5.4]
"A"
1-3/
4"[4
4.4]
21.7
4"[5
52.2
]5.42
"[1
37.7
]11
.96"
[303
.8]
4.96
"[1
26.0
]70
.87"
[180
0.2]
40.6
9"[1
033.
5]
21.8
4"[5
54.7
]
16.0
3"[4
07.2
]
1.75
"[4
4.5]
20.4
1"[5
18.3
]3.
00"
[76.
2]13
.78"
[350
.0]
14.0
0"[3
55.6
]
3.00
"[7
6.2]
15.1
9"[3
85.8
]
32.1
9"[8
17.6
]
3'-1
3/1
6"[9
44.6
]
"A"
1-3/
4"[4
4.5]
CR
BTM
PWR
001A
013/
4" [1
9] N
PT3/
4" [1
9] N
PT1/
2" [1
2.7]
NPT
CR
RFC
UR
B002
A01
CO
NN
ECTO
R P
KG. A
CC
.G
AS C
ON
NEC
TIO
N T
YPE
GAS
FIT
TIN
GPO
WER
WIR
ING
FI
TTIN
GC
ON
TRO
L W
IRIN
G
FITT
ING
ACC
ESSO
RY
CO
NVE
NIE
NC
E O
UTL
ET W
IRIN
G C
ON
NEC
TOR
THR
U T
HE
CU
RB
1/2"
[12.
7] N
PT1/
2" [1
2.7]
NPT
CR
BTM
PWR
003A
01TH
RU
TH
E BO
TTO
M
RO
OF
CU
RB
ACC
ESSO
RY
#A
CR
RFC
UR
B001
A01
14"
[356
]
24"
[610
]
NO
TES:
1. R
OO
FCU
RB
ACC
ESSO
RY
IS S
HIP
PED
DIS
ASSE
MBL
ED.
2. IN
SULA
TED
PAN
ELS:
25.
4 [1
"] TH
K. P
OLY
UR
ETH
ANE
FOAM
, 44.
5 [1
-3/4
] # D
ENSI
TY.
3. D
IMEN
SIO
NS
IN [
] AR
E IN
MIL
LIM
ETER
S.4.
RO
OFC
UR
B: 1
8 G
AGE
STEE
L.5.
ATT
ACH
DU
CTW
OR
K TO
CU
RB.
(FLA
NG
ES O
F D
UC
T R
EST
ON
CU
RB)
.6.
SER
VIC
E C
LEAR
ANC
E 4
FEET
ON
EAC
H S
IDE.
7.
DIR
ECTI
ON
OF
AIR
FLO
W.
8. C
ON
NEC
TOR
PAC
KAG
E C
RBT
MPW
R00
1A01
IS F
OR
TH
RU
-TH
E-C
UR
B G
AS T
YPE
PA
CKA
GE
CR
BTM
PWR
003A
01 IS
FO
R T
HR
U-T
HE-
BOTT
OM
TYP
E G
AS C
ON
NEC
TIO
NS.
TYPI
CAL
(4) S
IDES
SUPP
LY A
IRR
ETU
RN
AIR
RO
OFI
NG
MAT
ERIA
L(F
IELD
SU
PPLI
ED)
CAN
T ST
RIP
(FIE
LD S
UPP
LIED
)
RO
OFI
NG
FEL
T(F
IELD
SU
PPLI
ED)
CO
UN
TER
FLA
SHIN
G(F
IELD
SU
PPLI
ED)
UN
ITG
ASKE
T(S
UPP
LIED
WIT
H C
UR
B)
RIG
ID IN
SULA
TIO
N(F
IELD
SU
PPLI
ED)
DU
CT
(FIE
LD S
UPP
LIED
)
NAI
L (F
IELD
SU
PPLI
ED)
VIEW
"B"
CO
RN
ER D
ETAI
L
SEE
VIEW
"B"
RET
UR
N A
IRSU
PPLY
AIR
SUPP
LY A
IRO
PEN
ING
RET
UR
N A
IRO
PEN
ING
GAS
SER
VIC
E PL
ATE
THR
U T
HE
CU
RB
DR
ILL
HO
LE
2"
[50.
8] @
AS
SEM
BLY
(IF
REQ
UIR
ED)
(SEE
NO
TE #
8)
SEE
NO
TE #
2
11 3
/4"[2
98.5
] WID
EIN
SULA
TED
DEC
K PA
NEL
S
8 9/
16"[2
17.5
] WID
EIN
SULA
TED
DEC
K PA
NEL
1/3/
4"[4
4.5]
SCAL
E 0
.250
E-E
SEC
TIO
N
48TC
4004
27
RO
OF
CU
RB
DE
TIA
LS
Fig
. 2 —
48F
C**
04-0
7 R
oo
f C
urb
Acc
esso
ry D
etai
ls
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Printed in U.S.A. Form 48FC-4-7-02SB Pg 12 3-19 Replaces: 48FC-4-7-01SB
© Carrier Corporation 2019