4.3.4_KB-TZ_Expansion_Anchor_(316-327)r021a.pdf

Hilti, Inc. 5400 South 122nd East Avenue

Tulsa, OK 74146

1-800-879-8000 www.hilti.com

Attached are page(s) from the 2008 Hilti North American Product Technical Guide. For complete details on this product, including data development, product specifications, general suitability, installation, corrosion, and spacing & edge distance guidelines, please refer to the Technical Guide, or contact Hilti.

Hilti Product Technical Guide

Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.ca.hilti.com I Product Technical Guide 2008

P R O F I S

PROFIS:The World’s Most PowerfulAnchor Design Software

• Easy to Learn – Start working injust minutes

• Fast and Powerful – Produce detaileddesigns quickly

• Specify with Confidence – Thelargest number of approvals andlatest design codes

No charge.Download now at www.us.hilti.comor www.hilti.ca

Firestop SystemsWhen it comes to Life Safety and buildingcode compliance, Hilti provides completesolutions with a wide range of productsand unmatched technical support.

• Firestop Systems Guides- Through Penetrations- Joint Penetrations

• FACT Program• FS 411• BASIC Training• Engineering Judgements• Firestop Design Center onlineat www.us.hilti.com or www.hilti.ca

Hilti DiaphragmDeck DesignThe Hilti Diaphragm Deck DesignProgram allows designers to quicklyand accurately design roof deck andcomposite floor deck diaphragms.

• Ability to design with innovativeHilti fasteners for frame and sidelapconnection

• Creates easy to use load tables withspan ranges based on user input

• Allows for different safety factorsdepending on load type, buildingcode and field quality control

• Direct link to Hilti website

MI – IndustrialPipe SupportTechnical GuideA guide to specifying the Hilti modularpipe support system for medium toheavy loads without welding.

• MI System is the ideal solution forpipes up to 24 in. diameter

• Reliable fastenings without welds• Easily installed

Hilti Online• Technical Library• Design Centers• Interactive Product Advisors• Full-line Product Catalog• Online Ordering• Maps to Hilti locations• “Contact Us” program to

answer your questions

Prod_Tech_Guide_Cover_2008.qxd:MI_Kapitel_5_en.qxd 12/29/07 2:16 PM Page 4

Mechanical Anchoring Systems

4.3.4 Kwik Bolt TZ Expansion Anchor

316 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Product Technical Guide 2008

Listings/ApprovalsICC-ES (International Code Council)ESR-1917FM (Factory Mutual)Pipe Hanger Components for AutomaticSprinkler Systems (3/8" - 3/4")UL (Underwriters Laboratories)Pipe Hanger Equipment for FireProtection Services (3/8" - 3/4")

Impact Section(Dog Point)

Expansion Cone

Nut

Washer

RedSettingMark

AnchorBody

StainlessSteel

ExpansionSleeve

(Wedges)

AnchorThread

4.3.4.1 Product Description

4.3.4.2 Material Specifications

4.3.4.3 Technical Data

4.3.4.4 Installation Instructions

4.3.4.5 Ordering Information

4.3.4.6 Sample Calculations

The Kwik Bolt TZ (KB-TZ) is a torquecontrolled expansion anchor which isespecially suited to seismic and crackedconcrete applications. This anchor lineis available in carbon steel with zincelectroplated coating, 304 stainlesssteel, and 316 stainless steel versions.The anchor diameters range from 3/8 to3/4 inch in a variety of lengths.Applicable base materials includenormal-weight concrete, structurallightweight concrete, and lightweightconcrete over metal deck.

Guide Specifications

Torque controlled expansion anchorsshall be Kwik Bolt TZ (KB-TZ) suppliedby Hilti meeting the description inFederal Specification A-A 1923A, Type4. The anchor bears a lengthidentification mark embossed into theimpact section (dog point) of the anchorsurrounded by four embossed notchesidentifying the anchor as a Hilti KwikBolt TZ in the installed condition.Anchors are manufactured to meet oneof the following conditions:

• The carbon steel anchor body, nut,and washer have an electroplatedzinc coating conforming to ASTMB633 to a minimum thickness of 5µm. The stainless steel expansionsleeve conforms to AISI 316.

• Stainless steel anchor body, nutand washer conform to AISI 304.Stainless steel expansion sleeveconforms to AISI 316.

• Stainless steel anchor body, nut,washer, and expansion sleeve con-form to AISI 316 stainless steel.

Product Features

• Product and length identificationmarks facilitate quality control afterinstallation.

• Through fixture installation andvariable thread lengths improveproductivity and accommodatevarious base plate thicknesses.

• 316 Stainless Steel wedges pro-vide superior performance incracked concrete.

• Ridges on expansion wedgesprovide increased reliability.

• Mechanical expansion allowsimmediate load application.

• Raised impact section (dog point)prevents thread damage duringinstallation.

• Bolt meets ductility requirementsof ACI 318-05 Section D1.

Installation

Drill hole in base material to theappropriate depth using a Hilti carbidetipped drill bit. Drive the anchor into thehole using a hammer. A minimum of fourthreads must be below the fasteningsurface prior to applying installationtorque. Tighten the nut to therecommended installation torque.

4.3.4.1 Kwik Bolt TZ Product Description

Supplemental Design Provisions for ACI 318-05 Appendix D

Design strengths are determined in accordance with ACI 318-05 Appendix D andICC Evaluation Service ESR-1917 Hilti Kwik Bolt TZ Carbon and Stainless SteelAnchors in Concrete. The relevant design parameters are reiterated in Tables 1, 2,and 3 of this document. Supplemental provisions required for the design of theKB-TZ are enumerated in Section 4.0 of ESR-1917 (DESIGN AND INSTALLATION).Note that these design parameters are supplemental to the design provisionsof ACI 318-05.

C

Building Code ComplianceIBC® 2006IRC® 2006UBC® 1997


Kwik Bolt TZ Expansion Anchor 4.3.4

Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Product Technical Guide 2008 317

4.3.4.2 Material SpecificationsCarbon steel with electroplated zinc• Carbon steel KB-TZ anchors have the following minimum bolt fracture loads1

• Carbon steel anchor components plated in accordance with ASTM B633 to a minimum thickness of 5µm.

• Nuts conform to the requirements of ASTM A563, Grade A, Hex.

• Washers meet the requirements of ASTM F844.

• Expansion sleeves (wedges) are manufactured from AISI 316 stainless steel.

Stainless steel• Stainless steel KB-TZ anchors are made of AISI 304 or 316 material and have the following minimum bolt fracture loads1

• All nuts and washers are made from AISI 304 or AISI 316 stainless steel respectively.

• Nuts meet the dimensional requirements of ASTM F594.

• Washers meet the dimensional requirements of ANSI B18.22.1, Type A, plain.

• Expansion Sleeve (wedges) are made from AISI 316.

1 Bolt fracture loads are determined by testing in jig as part of product QC. These loads are not intended for design purposes. See Tables 2 and 3.

Anchor Shear TensionDiameter (in.) (lb) (lb)

3/8 NA 67441/2 7419 112405/8 11465 175353/4 17535 25853

Anchor Shear TensionDiameter (in.) (lb) (lb)

3/8 5058 65191/2 8543 123645/8 13938 191093/4 22481 24729




4.3.4.3 Technical DataTable 1 — Kwik Bolt TZ Specification Table

SETTING Symbol Units Nominal anchor diameter (in.)

INFORMATION 3/8 1/2 5/8 3/4

Anchor O.D. d oin. 0.375 0.5 0.625 0.75

(mm) (9.5) (12.7) (15.9) (19.1)

Nominal bit dbit in. 3/8 1/2 5/8 3/4diameter

Effective min. hefin. 2 2 3-1/4 3-1/8 4 3-3/4 4-3/4

embedment (mm) (51) (51) (83) (79) (102) (95) (121)

Min. hole depth h oin. 2-5/8 2-5/8 4 3-3/4 4-3/4 4-5/8 5-3/4

(mm) (67) (67) (102) (95) (121) (117) (146)

Min. thickness of tminin. 1/4 3/4 1/4 3/8 3/4 1/8 1-5/8

fixture1 (mm) (6) (19) (6) (9) (19) (3) (41)

Max. thickness of tmaxin. 2-1/4 4 2-3/4 5-5/8 4-3/4 4-5/8 3-5/8

fixture (mm) (57) (101) (70) (143) (121) (117) (92)

Installation torque Tinstft-lb 25 40 60 110

(Nm) (34) (54) (81) (149)

Min. dia. of hole dhin. 7/16 9/16 11/16 13/16

in fixture (mm) (11.1) (14.3) (17.5) (20.6)

Available anchor� anch

in. 3 3-3/4 5 3-3/4 4-1/2 5-1/2 7 4-3/4 6 8-1/2 10 5-1/2 8 10

lengths (mm) (76) (95) (127) (95) (114) (140) (178) (121) (152) (216) (254) (140) (203) (254)

Threaded length� thread

in. 7/8 1-5/8 2-7/8 1-5/8 2-3/8 3-3/8 4-7/8 1-1/2 2-3/4 5-1/4 6-3/4 1-1/2 4 6

including dog point (mm) (22) (41) (73) (41) (60) (86) (178) (38) (70) (133) (171) (38) (102) (152)

Unthreaded length � unthrin. 2-1/8 2-1/8 3-1/4 4

(mm) (54) (54) (83) (102)

Installation hnomin. 2-1/4 2-3/8 3-5/8 3-5/8 4-1/2 4-3/8 5-3/8

embedment (mm) (57) (60) (92) (92) (114) (111) (137)

1 The minimum thickness of the fastened part is based on use of the anchor at minimum embedment and is controlled by the length of thread. If a thinner fastening thickness isrequired, increase the anchor embedment to suit.

Figure 1 — Kwik Bolt TZ installed

tdh

do

anch

unthr

thread

hef hohnom




DESIGN Symbol Units Nominal anchor diameterINFORMATION 3/8 1/2 5/8 3/4

Anchor O.D. doin. 0.375 0.5 0.625 0.75

(mm) (9.5) (12.7) (15.9) (19.1)Effective min. hef

in. 2 2 3-1/4 3-1/8 4 3-3/4 4-3/4embedment1 (mm) (51) (51) (83) (79) (102) (95) (121)

Min. member thickness hminin. 4 5 4 6 6 8 5 6 8 6 8 8

(mm) (102) (127) (102) (152) (152) (203) (127) (152) (203) (152) (203) (203)

Critical edge distance cacin. 4-3/8 4 5-1/2 4-1/2 7-1/2 6 6-1/2 8-3/4 6-3/4 10 8 9

(mm) (111) (102) (140) (114) (191) (152) (165) (222) (171) (254) (203) (229)

ca,minin. 2-1/2 2-3/4 2-3/8 3-5/8 3-1/4 4-3/4 4-1/8

Min. edge distance (mm) (64) (70) (60) (92) (83) (121) (105)for s � in. 5 5-3/4 5-3/4 6-1/8 5-7/8 10-1/2 8-7/8

(mm) (127) (146) (146) (156) (149) (267) (225)smin in. 2-1/2 2-3/4 2-3/8 3-1/2 3 5 4

Min. anchor spacing (mm) (64) (70) (60) (89) (76) (127) (102)

for c �in. 3-5/8 4-1/8 3-1/2 4-3/4 4-1/4 9-1/2 7-3/4

(mm) (92) (105) (89) (121) (108) (241) (197)Min. hole depth ho

in. 2-5/8 2-5/8 4 3-7/8 4-3/4 4-5/8 5-3/4in concrete (mm) (67) (67) (102) (98) (121) (117) (146)Min. specified f y

lb/in2 100000 84800 84800 84800yield strength (N/mm2) (690) (585) (585) (585)Min. specified fu

lb/in2 125000 106000 106000 106000ult. strength (N/mm2) (862) (731) (731) (731)Effective tensile A se

in2 0.052 0.101 0.162 0.237stress area (mm2) (33.6) (65.0) (104.6) (152.8)Steel strength N sa

lb 6500 10705 17170 25120in tension (kN) (28.9) (47.6) (76.4) (111.8)Steel strength Vsa

lb 3595 6405 10555 15930in shear (kN) (16.0) (28.5) (47.0) (70.9)Steel strength in Vs,seis

lb 2255 6405 10555 14245shear, seismic (kN) (10.0) (28.5) (47.0) (63.4)Steel strength in shear, Vs,deck

lb 2130 3000 4945 4600 6040 NPconcrete on metal deck2 (kN) (9.5) (13.3) (22) (20.5) (26.9)Pullout strength Np,uncr

lb 2515 NA 5,515 NA 9,145 8,280 10,680uncracked concrete3 (kN) (11.2) (24.5) (40.7) (36.8) (47.5)Pullout strength Np,cr

lb 2270 NA 4,915 NA NAcracked concrete 3 (kN) (10.1) (21.9)Pullout strength concrete Np,deck,cr

lb 1460 1460 2620 2000 4645 NPon metal deck4 (kN) (6.5) (6.5) (11.7) (8.9) (20.7)Anchor category5 1Effectiveness factor kuncr uncracked concrete 24Effectiveness factor k cr cracked concrete6 17�c,N = kuncr /k cr

7 1.41Strength reduction factor � for tension, steel failure modes8 0.75

Strength reduction factor � for shear, steel failure modes8 0.65

Strength reduction factor � for tension, concrete failure modes, Condition B9 0.65

Strength reduction factor � for shear, concrete failure modes 0.70

Table 2 — Carbon Steel Kwik Bolt TZ Strength Design Information

1 See Fig. 1.2 NP (not permitted) denotes that the condition is not supported.3 NA (not applicable) denotes that this value does not control for

design.4 NP (not permitted) denotes that the condition is not supported.

Values are for cracked concrete. Values are applicable to bothstatic and seismic load combinations.

5 See ACI 318 D.4.4.6 See ACI 318 D.5.2.2.

7 See ACI 318 D.5.2.6.8 The KB-TZ is a ductile steel element as defined by ACI 318 D.1.9 For use with the load combinations of ACI 318 9.2. Condition B

applies where supplementary reinforcement in conformance withACI 318 D.4.4 is not provided, or where pullout or pryout strengthgoverns. For cases where the presence of supplementary rein-forcement can be verified, the strength reduction factors associated with Condition A may be used.

DESIGN Symbol Units Nominal anchor diameterINFORMATION 3/8 1/2 5/8 3/4

Anchor O.D. d oin. 0.375 0.5 0.625 0.75

(mm) (9.5) (12.7) (15.9) (19.1)Effective min. hef

in. 2 2 3-1/4 3-1/8 4 3-3/4 4-3/4embedment1 (mm) (51) (51) (83) (79) (102) (95) (121)

Min. member thickness hminin. 4 5 4 6 6 8 5 6 8 6 8

(mm) (102) (127) (102) (152) (152) (203) (127) (152) (203) (152) (203)

Critical edge distance cacin. 4-3/8 3-7/8 5-1/2 4-1/2 7-1/2 6 7 8-7/8 6 10 7 9

(mm) (111) (98) (140) (114) (191) (152) (178) (225) (152) (254) (178) (229)

ca,minin. 2-1/2 2-7/8 2-1/8 3-1/4 2-3/8 4-1/4 4

Min. edge distance (mm) (64) (73) (54) (83) (60) (108) (102)

for s �in. 5 5-3/4 5-1/4 5-1/2 5-1/2 10 8-1/2

(mm) (127) (146) (133) (140) (140) (254) (216)

sminin. 2-1/4 2-7/8 2 2-3/4 2-3/8 5 4

Min. anchor spacing (mm) (57) (73) (51) (70) (60) (127) (102)

for c �in. 3-1/2 4-1/2 3-1/4 4-1/8 4-1/4 9-1/2 7

(mm) (89) (114) (83) (105) (108) (241) (178)Min. hole depth ho

in. 2-5/8 2-5/8 4 3-3/4 4-3/4 4-5/8 5-3/4in concrete (mm) (67) (67) (102) (95) (121) (117) (146)Min. specified f y

lb/in2 92000 92000 92000 76125yield strength (N/mm2) (634) (634) (634) (525)Min. specified fu

lb/in2 115000 115000 115000 101500ult. strength (N/mm2) (793) (793) (793) (700)Effective tensile A se

in2 0.052 0.101 0.162 0.237stress area (mm2) (33.6) (65.0) (104.6) (152.8)Steel strength N sa

lb 5980 11615 18630 24055in tension (kN) (26.6) (51.7) (82.9) (107.0)Steel strength Vsa

lb 4870 6880 11835 20050in shear (kN) (21.7) (30.6) (52.7) (89.2)Steel strength in tension, N sa,seis

lb NA 2,735 NA NA NAseismic2 (kN) (12.2)Steel strength in shear, V sa,seis

lb 2825 6880 11835 14615seismic2 (kN) (12.6) (30.6) (52.6) (65.0)Pullout strength Npn,uncr

lb 2630 NA 5760 NA NA 12040uncracked concrete 2 (kN) (11.7) (25.6) (53.6)Pullout strength cracked Npn,cr

lb 2340 3180 NA NA 5840 8110 NAconcrete2 (kN) (10.4) (14.1) (26.0) (36.1)Anchor category3 1Effectiveness factor kuncr uncracked concrete 24Effectiveness factor k cr cracked concrete4 17 24 17 17 17 24 17�c,N = kuncr /kcr5 1.41 1.00 1.41 1.41 1.41 1.00 1.41Strength reduction factor � for tension, steel failure modes 6 0.75

Strength reduction factor � for shear, steel failure modes 6 0.65

Strength reduction factor � for tension, concrete failure modes, Condition B 7 0.65

Strength reduction factor � for shear, concrete failure modes 0.70




Table 3 — Stainless Steel Kwik Bolt TZ Strength Design Information

1 See Fig. 1.2 NA (not applicable) denotes that this value does not control for design.3 See ACI 318 D.4.4.4 See ACI 318 D.5.2.2.5 See ACI 318 D.5.2.6.6 The KB-TZ is a ductile steel element as defined by ACI 318 D.1.7 For use with the load combinations of ACI 318 9.2. Condition B applies where supplementary reinforcement in conformance with ACI 318

D.4.4 is not provided, or where pullout or pryout strength governs. For cases where the presence of supplementary reinforcement can beverified, the strength reduction factors associated with Condition A may be used.




Figure 2 — Interpolation of Minimum Edge Distance and Anchor Spacing

Figure 3 — Installation in Concrete over Metal Deck Floor

Table 4 — Mean Axial Stiffness Values (1000 lb/in.) for Kwik Bolt TZ Carbonand Stainless Steel Anchors in Normal-Weight Concrete1

Concrete condition carbon steel KB-TZ, all diameters stainless steel KB-TZ, all diametersuncracked concrete 700 120cracked concrete 500 90

1 Mean values shown. Actual stiffness may vary considerably depending on concrete strength, loading and geometry of application.

Min. 4-1/2"

UpperFlute(Valley)

LowerFlute(Ridge)

Min. 4-1/2"

Max. 1" Offset Typical

MinimumNo. 20 GaugeSteel Deck

Min. 5/8" Typical

Max

. 3"

Min

. 1-1

/2"

Min. 3000 psi Normal or Sand -Lightweight Concrete

Anch

orin

Rid

ge

ca, min at s >

sdesign

cdesign edge distance c

smin at c >




Table 6 - Kwik Bolt TZ Carbon and Stainless Steel Allowable Static Tension (ASD),Normal-Weight Uncracked Concrete, Condition B (lb)1,2,3,4

Concrete Compressive Strength2

Nominal Embedment f 'c= 2500 psi f 'c= 3000 psi f 'c= 4000 psi f 'c= 6000 psiAnchor Depth hef Carbon Stainless Carbon Stainless Carbon Stainless Carbon Stainless

Diameter (in.) Steel Steel Steel Steel Steel Steel Steel Steel

3/8 2 1168 1221 1279 1338 1477 1545 1809 1892

1/22 1576 1576 1726 1726 1993 1993 2441 2441

3-1/4 2561 2674 2805 2930 3239 3383 3967 4143

5/83-1/8 3078 3078 3372 3372 3893 3893 4768 4768

4 4246 4457 4651 4883 5371 5638 6578 6905

3/43-3/4 3844 4046 4211 4432 4863 5118 5956 62684-3/4 4959 5590 5432 6124 6272 7071 7682 8660

Table 7 - Kwik Bolt TZ Carbon and Stainless Steel Allowable Static Tension (ASD),Normal-Weight Cracked Concrete, Condition B (lb)1,2,3,4




3/8 2 1054 1086 1155 1190 1333 1374 1633 1683

1/22 1116 1476 1223 1617 1412 1868 1729 2287

3-1/4 2282 2312 2500 2533 2886 2925 3535 3582

5/83-1/8 2180 2180 2388 2388 2758 2758 3377 3377

4 3157 2711 3458 2970 3994 3430 4891 4201

3/43-3/4 2866 3765 3139 4125 3625 4763 4440 58334-3/4 4085 4085 4475 4475 5168 5168 6329 6329

Allowable Stress Design

Design values for use with allowable stress design (working stress design) shall be established as follows: Rallow,ASD = Rdα

where Rd = � Rk represents the limiting design strength in tension (� Nn ) or shear ( � Vn ) as calculated according to ACI 318 D.4.1.1 and D.4.1.2

Table 5 — The value of α shall be taken as follows:

Reference for strength αreduction factors including seismic excluding seismic

ACI 318 D.4.4 1.1 1.4ACI 318 D.4.5 1.2 1.55

1 Values are for single anchors with no edge distance or spacing reduction. For other cases, calculation of Rd as per ACI 318-05 and conversion to ASD in accordance with Table 5.

2 Values are for normal weight concrete. For sand-lightweight concrete, multiply values by 0.85. For all-lightweight concrete, multiply values by 0.75. See ACI 318-05 D.3.4.

3 Condition B applies where supplementary reinforcement in conformance with ACI 318-05 D.4.4 is not provided, or where pullout or pryout strength governs. For cases where thepresence of supplementary reinforcement can be verified, the strength reduction factors associated with Condition A may be used.

4 Allowable static tension loads for 2,500 psi are calculated by multiplying the concrete breakout strength Nb by the strength reduction φ factor of 0.65 and dividing by an α of 1.4according to ICC ESR-1917 Section 4.2. Nb is calculated as per ACI 318-05 D.5.2.2. This load may be adjusted for other concrete strengths according to ICC ESR-1917 Section4.1.3 by using the following equation.

Nb,f'c = Nbf 'c

2500




4 Allowable static tension loads for 2,500 psi are calculated by multiplying the pullout strength Npn by the strength reduction φ factor of 0.65 and dividing by an α of 1.4 according toICC ESR-1917 Section 4.2. See Table 2 for Npn. This load may be adjusted for other concrete strengths according to ICC ESR-1917 Section 4.1.3 by using the following equation.

Npn,cr,f'c = Npn,crf 'c

2500




Table 9 - Kwik Bolt TZ Carbon and Stainless Steel Allowable Seismic Tension (ASD),Normal-Weight Cracked Concrete, Condition B (lb)1,2,3,4




3/8 2 1006 1037 1102 1136 1273 1312 1559 1607

1/22 1065 1212 1167 1328 1348 1533 1651 1878

3-1/4 2178 2207 2386 2418 2755 2792 3375 3419

5/83-1/8 2081 2081 2280 2280 2632 2632 3224 3224

4 3014 2588 3301 2835 3812 3274 4669 4010

3/43-3/4 2736 3594 2997 3937 3460 4546 4238 55684-3/4 3900 3900 4272 4272 4933 4933 6042 6042

1 Values are for single anchors with no edge distance or spacingreduction due to concrete failure.

2 Allowable static shear loads are calculated by multiplying Vsa by thestrength reduction φ factor of 0.65 and dividing by an α of 1.4according to ICC ESR-1917 Section 4.2. See Table 2 for Vsa .

Table 8 - Kwik Bolt TZ Carbon and Stainless SteelAllowable Static Shear (ASD), Steel (lb)1,2

Nominal Allowable Steel Capacity, Static ShearAnchor

Diameter Carbon Steel Stainless Steel

3/8 1669 26611/2 2974 31945/8 4901 54953/4 7396 9309

1 Values are for single anchors with no edge distance or spacing reductiondue to concrete failure.

2 Allowable seismic shear loads are calculated by multiplying Vsa, seis by thestrength reduction φ factor of 0.65, then multiply by 0.75 as per ACI 318-05 D.3.3.3, and dividing by an α of 1.1 according to ICC ESR-1917 Section4.2. See Table 2 for Vsa, seis .

Table 10 - Kwik Bolt TZ Carbon and Stainless SteelAllowable Seismic Shear (ASD), Steel (lb)1,2

Nominal Allowable Steel Capacity, Seismic ShearAnchor

Diameter Carbon Steel Stainless Steel

3/8 999 12521/2 2839 30495/8 4678 52453/4 6313 6477




4 Allowable seismic tension loads for 2,500 psi are calculated by multiplying the pullout strength Npn by the strength reduction φ factor of 0.65, then multiplying by a 0.75 factordescribe in ACI 318-05 D.3.3.3, and dividing by an α of 1.1 according to ICC ESR-1917 Section 4.2. See Table 2 for Npn. This load may be adjusted for other concretestrengths according to ICC ESR-1917 Section 4.1.3 by using the following equation.

Npn,cr,f'c = Npn,crf 'c

2500




Table 12 — Kwik Bolt TZ Length Identification System

Figure 4 — Bolt Head with Length Identification Mark and Kwik Bolt TZ Head Notch Embossment

Length ID marking A B C D E F G H I J K L M N O P Q R S T U V Won bolt headLength of From 11⁄2 2 21⁄2 3 31⁄2 4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8 81⁄2 9 91⁄2 10 11 12 13 14 15anchor, Up to but�anch (in.) not 2 21⁄2 3 31⁄2 4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8 81⁄2 9 91⁄2 10 11 12 13 14 15 16

including

1 Pullout strength values Npn,deck are for anchors installed in lightweight concrete having a minimum 2,500 psi compressive strength at the time of installation. See Table 3ESR-1917. The values listed in Table 11 have been calculated assuming a minimum 3,000 psi concrete compressive strength. The pullout strength may be adjusted forother lightweight concrete compressive strengths according to ICC ESR-1917 Section 4.1.3 using the following equation:

2 Minimum anchor spacing along the flute shall be the greater of 3.0 h ef or 1.5 times the flute width in accordance with ICC ESR-1917 Section 4.1.3.

3 Anchors in the lower flute may be installed with a maximum 1-inch offset in either direction. See Figure 5 in ESR-1917.

4 Allowable seismic tension and shear loads are calculated by multiplying Npn,deck and V sa,deck by the strength reduction φ factor of 0.65, the seismic reduction φ factor of0.75 according to ACI 318 D3.3.3, and then divided by an α of 1.1 according to ICC ESR-1917 Section 4.2.

5 Allowable non-seismic tension and shear loads are calculated by multiplying Npn,deck and V sa,deck by the strength reduction φ factor of 0.65 and dividing by an α of 1.4according to ICC ESR-1917 Section 4.2.

Table 11 - Kwik Bolt TZ Carbon Steel Allowable Tension and Shear Loads (ASD),Installed into the Underside of a Lightweight Concrete over Metal Deck Slab1,2,3

Nominal Embedment Tension Tension Shear ShearAnchor Depth hef Seismic non-Seismic Seismic non-Seismic

Diameter (in.) (lb)4 (lb)5 (lb)4 (lb)5

3/8 2 709 743 944 9891/2 2 709 743 1330 13931/2 3-1/4 1272 1333 2192 22965/8 3-1/8 971 1017 2039 21365/8 4 2255 2362 2677 2804

Npn,deck,f'c = Npn,deck (lb, psi)f 'c2500




1. Hammer drill a hole to the same nominal diameter as the Kwik Bolt TZ. The hole depthmust exceed the anchor embedment by at least1/4 inch. The fixture may be used as a drillingtemplate to ensure proper anchor location.

2. Clean hole.

3. Drive the Kwik Bolt TZ into the hole usinga hammer. The anchor must be drivenuntil at least 4 threads are below the surface of the fixture.

4. Tighten the nut to the recommendedinstallation torque.

4.3.4.4 Kwik Bolt TZ Anchor Installation Instructionsinto normal-weight and lightweight concrete




4.3.4.5 Kwik Bolt TZ Anchor Ordering Information

Item No. Description Length (in.) Thread Length (in.) Box Quantity

387509 KB-TZ 3/8x3 3 7/8 50387510 KB-TZ 3/8x3-3/4 3-3/4 1-5/8 50387511 KB-TZ 3/8x5 5 2-7/8 50387512 KB-TZ 1/2x3-3/4 3-3/4 1-5/8 20387513 KB-TZ 1/2x4-1/2 4-1/2 2-3/8 20387514 KB-TZ 1/2x5-1/2 5-1/2 3-3/8 20387515 KB-TZ 1/2x7 7 4-7/8 20387516 KB-TZ 5/8x4-3/4 4-3/4 1-1/2 15387517 KB-TZ 5/8x6 6 2-3/4 15387518 KB-TZ 5/8x8-1/2 8-1/2 5-1/4 15387519 KB-TZ 5/8x10 10 6-3/4 15387520 KB-TZ 3/4x5-1/2 5 1/2 1-1/2 10387521 KB-TZ 3/4x8 8 4 10387522 KB-TZ 3/4x10 10 6 10

387523 KB-TZ SS304 3/8x3 3 7/8 50387524 KB-TZ SS304 3/8x3-3/4 3-3/4 1-5/8 50387525 KB-TZ SS304 3/8x5 5 2-7/8 50387526 KB-TZ SS304 1/2x3-3/4 3-3/4 1-5/8 20387527 KB-TZ SS304 1/2x4-1/2 4-1/2 2-3/8 20387528 KB-TZ SS304 1/2x5-1/2 5-1/2 3-3/8 20387529 KB-TZ SS304 1/2x7 7 4-7/8 20387530 KB-TZ SS304 5/8x4-3/4 4-3/4 1-1/2 15387531 KB-TZ SS304 5/8x6 6 2-3/4 15387532 KB-TZ SS304 5/8x8-1/2 8-1/2 5-1/4 15387533 KB-TZ SS304 5/8x10 10 6-3/4 15387534 KB-TZ SS304 3/4x5-1/2 5-1/2 1-1/2 10387535 KB-TZ SS304 3/4x8 8 4 10387536 KB-TZ SS304 3/4x10 10 6 10

411727 KB-TZ SS316 3/8x3 3 7/8 50411731 KB-TZ SS316 3/8x3-3/4 3-3/4 1-5/8 50411733 KB-TZ SS316 1/2x3-3/4 3-3/4 1-5/8 20411734 KB-TZ SS316 1/2x4-1/2 4-1/2 2-3/8 20411736 KB-TZ SS316 1/2x5-1/2 5-1/2 3-3/8 20411737 KB-TZ SS316 5/8x4-3/4 4-3/4 1-1/2 15411739 KB-TZ SS316 5/8x6 6 2-3/4 15411740 KB-TZ SS316 3/4x5-1/2 5-1/2 1-1/2 10411741 KB-TZ SS316 3/4x10 10 6 10




Given:(2) 1/2 in. KB-TZ anchors understatic tension load as shown.hef = 3.25 in.Normal wt. concrete, f'c = 3,000 psiNo supplementary reinforcing.Assume uncracked concrete.Condition B per ACI 318-05 D.4.4(c)Calculate the allowable tension loadfor this configuration.

Calculation per ACI 318-05 Appendix D and ICC ESR-1917. Code Ref. Reference

Step 1. Calculate steel strength of anchor in tension: � N n = �n * N sa = 0.75 * 2 * 10,706 = 16,059 lb D.5.1.2D.4.4 Table 2

Step 2. Calculate concrete breakout strength of anchor in tension. See ESR-1917 for edge factor �cp,N .

N cbg =A N c (� ec,N ) (� ed,N,c,N ) (� cp,N ) N b

D.5.2.1 ESR-1917

A Nco4.1.2

Step 2a. Verify minimum member thickness, spacing and edge distance: D.8 Table 2

hmin = 6 in. � 6 in. ... ok Fig. 2

cmin = 4 in. > 3.5 in.

... smin defaults to 2.375 in.

6 in. > 2.375 in. ... ok

Step 2b. Check: 1.5h ef = (1.5 ) (3.25) = 4.88 in. > c 3.0h ef = (3) (3.25) = 9.75 in. > s D.5.2.1 Table 2

Step 2c. Calculate ANco and ANc for the anchorage: ANco = 9hef2 = (9) (3.25)2 = 95.1 in2

ANc = (1.5) (hef + c ) (3) (hef + s ) = [(1.5) (3.25) + 4] [(3 x 3.25) + 6] = 139.8 in2 < 2ANco ... okD.5.2.1 Table 2

Step 2d. Calculate � ec,N : eN' = O, � ec,N = 1 D.5.2.4

Step 2e. Calculate N b : N b = k cr f 'c ( hef )1.5 = 17 3000 (3.25)1.5 = 5,456 lb D.5.2.2 Table 2

Step 2f. Calculate modification factor for edge distance: � ed,N = 0.7 + 0.3 4 = 0.95 D.5.2.5 Table 2(1.5) (3.25)

Step 2g. � c,N = 1.4 (uncracked concrete) D.5.2.6 Table 2

Step 2h. Calculate modification factor for splitting:

� cp,N = c a,min �1.5h e f check: 4 = 0.53 : (1.5) (3.25) = 0.65⇒ 0.53 < 0.65 ... 1.5hef controls D.5.2.7 Table 2

c ac c ac 7.5 7.5 c ac

Step 2i. Calculate N cbg : N cbg = 139.8 (1) (0.95) (1.4) (5,456) (0.65) = 6,983 lb D.5.2.1 Table 295.1

Step 3. Check pullout strength: See ESR-1917 for adjustment for concrete strengthD.5.3.2

: Npn,f'c(1) = 2 [Npn, uncr ] = 2 [(5,515) ] = 12,082 lb

Step 4. Controlling strength: � N cbg = (0.65) (6,983) = 4,539 lb < � Nn ... � N cbg controls D.4.4(c) Table 2

Step 5. Convert value to ASD: T allow = 4,539 = 3,242 lb1.4 - Table 5

6"

Table 2ESR-19174.1.6

f 'c2500

30002500

3.5, 2.3752.375 controls0.875 Cmin

Smin

2.375, 5.75

s=6''

AN1.5hef

1.5hef c=4''1.5hef

4.3.4.6 Kwik Bolt TZ Anchor Sample Calculations

( )





PROFIS

PROFIS:The World’s Most PowerfulAnchor Design Software

• Easy to Learn – Start working injust minutes

• Fast and Powerful – Produce detaileddesigns quickly

• Specify with Confidence – Thelargest number of approvals andlatest design codes

No charge.Download now @ www.us.hilti.com

Firestop SystemsWhen it comes to Life Safety and buildingcode compliance, Hilti provides completesolutions with a wide range of productsand unmatched technical support.

• Firestop Systems Guides- Through Penetrations- Joint Penetrations

• FACT Program• FS 411• BASIC Training• Engineering Judgements• Firestop Design Center online@ www.us.hilti.com

Hilti DiaphragmDeck DesignThe Hilti Diaphragm Deck DesignProgram allows designers to quicklyand accurately design roof deck andcomposite floor deck diaphragms.

• Ability to design with innovativeHilti fasteners for frame and sidelapconnection

• Creates easy to use load tables withspan ranges based on user input

• Allows for different safety factorsdepending on load type, buildingcode and field quality control

• Direct link to Hilti website

MI – IndustrialPipe SupportTechnical GuideA guide to specifying the Hilti modularpipe support system for medium toheavy loads without welding.

• MI System is the ideal solution forpipes up to 24 in. diameter

• Reliable fastenings without welds• Easily installed

PAYMENT TERMS: Net 30 days from date of invoice. Customer agrees to pay allcosts incurred by Hilti in collecting any delinquent amounts,including attorney’s fees.

FREIGHT: All sales are F.O.B. Destination with transportation allowed via Hiltidesignated mode. Delivery dates are estimates only. Additionalcharges for expedited shipments, special handling requirements,and orders below certain dollar amounts shall be the responsibilityof Customer. Fuel surcharges may apply depending on marketconditions.

CREDIT: All orders sold on credit are subject to Credit Department approval.

RETURN POLICY: Products must be in saleable condition to qualify for return.Saleable condition is defined as unused items in originalundamaged packaging and unbroken quantities and in as-newcondition. All returns are subject to Hilti inspection andacceptance, and a $125 restocking charge if returned morethan 90 days after invoice date. Proof of purchase is requiredfor all returned materials. Special orders products anddiscontinued items are not eligible for return credit. Datedmaterials are only returnable in case quantity, and within 30days after invoice date.

WARRANTY: Hilti warrants that for a period of 12 months from the date it sells aproduct it will, at its sole option and discretion, refund the purchaseprice, repair, or replace such product if it contains a defect inmaterial or workmanship. Absence of Hilti’s receipt of notification ofany such defect within this 12-month period shall constitute awaiver of all claims with regard to such product.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHERWARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. Hilti shall in noevent be liable for, and Customer hereby agrees to indemnify Hiltiagainst all claims related to special, direct, indirect, incidental,consequential, or any other damages arising out of or related to thesale, use, or inability to use the product.

ACCEPTANCE OF ORDER: Acceptance is limited to the express terms contained herein, andterms are subject to change by Hilti without notice. Additional ordifferent terms proposed by Customer are deemed material and areobjected to and rejected, but such rejection shall not operate as arejection of the offer unless it contains variances in the terms of thedescription, quantity, price or delivery schedule of the goods.Orders are not deemed “accepted” by Hilti unless and until it shipsthe associated items.

DOMESTIC ORIGIN: Any non-domestic Hilti product will be so identified on shippingdocuments and invoices for customers who properly identifythemselves as a federal government entity. All other customersmay obtain such information by written request to Hilti, Inc.,Contract Compliance, P.O. Box 21148, Tulsa, Oklahoma 74121.Hilti’s Quality Department personnel are the only individualsauthorized to warrant the country of origin of Hilti products.

BUSINESS SIZE: Hilti is a large business.

PRICES: Prices are those stated on the order, and unless otherwise notedare based on purchasing all items on the order — pricing forindividual products may vary for purchases of different quantities oritem combinations. Hilti does not maintain most favored customerrecords, makes no representation with respect to same, and rejectsany price warranty terms proposed by Customer. Hilti's publishednet price list is subject to change without notice.

CONSENT TO JURISDICTION: All transactions made pursuant hereto shall be deemed to havebeen made and entered into in Tulsa, Oklahoma. Any and alldisputes arising directly or indirectly from such transactions shall beresolved in the courts of the County of Tulsa, State of Oklahoma, tothe exclusion of any other court, and any resulting judgment maybe enforced by any court having jurisdiction of such an action. Alltransactions shall be governed by and construed in accordancewith the laws of the State of Oklahoma.

INDEMNIFICATION: Customer hereby agrees to indemnify Hilti for any costs, includingattorney’s fees, incurred by Hilti as a result, in whole or in part, ofany violation by Customer of any Federal, State or Local statute orregulation, or of any nationally accepted standard. It shall beCustomer’s sole responsibility to comply with all applicable lawsand regulations regarding the handling,use, transportation, ordisposal of products upon taking possession of same.

AUTHORIZATION: HILTI LEGAL DEPARTMENT PERSONNEL ARE THE ONLYINDIVIDUALS AUTHORIZED TO MODIFY THESE TERMS ANDCONDITIONS, WARRANT PRODUCT SUITABILITY FOR SPECIFICAPPLICATIONS, OR EXECUTE CUSTOMER DOCUMENTS, ANDANY SUCH ACTION IS NULL AND VOID UNLESS IN WRITTENFORM SIGNED BY SUCH INDIVIDUAL.

PAYMENT TERMS: Net 30 days from date of invoice.Customer agrees to pay all costs incurredby Hilti in collecting delinquent amounts, ifany, including reasonable attorney’s fees.

FREIGHT: Sales are F.O.B. Destination Point withtransportation allowed via Hilti designatedmode. Additional charges may apply forexpedited delivery, special handlingrequirements, and order under certainlimits. A fuel surcharge may applydepending on market conditions.

CREDIT: All orders sold on credit are subject toCredit Department approval.

RETURN POLICY: Product may be returned prepaid (unlessotherwise authorized) to Hilti provided:

i) it is returned by the original purchaser

ii) it is not dated product returned morethan 30 days after the original deliverydate

iii) it is not discontinued, clearance orspecial order product

iv) it is unused, in original packaging andin unbroken quantities.

Hilti will inspect product and, if the aboverequirements are satisfied, will credit tocustomer the original purchase price. A15% restocking fee may apply.

WARRANTY: Other than the manufacturer’s publishedwarranty, no warranties or conditions,express or implied, written or oral,statutory or otherwise are implied. Any andall conditions and warranties implied bylaw or by the Sale of Goods Act or anysimilar statutes of any Province are herebyexpressly waived.

TITLE TO PRODUCT: Title to product remains with Hilti until thetotal purchase price of product is paid.

PRICES: Customer agrees to pay Hilti prices set outon invoice. Customer agrees to pay taxesas indicated on invoice unless Hiltireceives acceptable exemptioncertificates.

INDEMNIFICATION: Customer agrees to use product at ownrisk and to indemnify Hilti against allliabilities, including legal fees, to thirdparties arising out of the use orpossession thereof. Hilti shall in no eventbe liable for special, incidental orconsequential damages.

CHANGES: Hilti sales personnel are not authorized tomodify these Terms and Conditions ormodify Customer’s credit terms. Terms aresubject to change by Hilti with reasonablenotice to Customer.

CASH SALES: Payment in full is due prior to goods beingreleased.

QUOTATIONS: All terms and conditions apply oncecustomer agrees to purchase product.Quotations on special promotion productsare only valid until end of promotionperiod.

In The United Sates In Canada

Hilti Online• Technical Library• Design Centers• Interactive Product Advisors• Full-line Product Catalog• Online Ordering• Maps to Hilti locations• “Contact Us” program to

answer your questions

4.3.4_KB-TZ_Expansion_Anchor_(316-327)r021a.pdf

Documents

Transcript of 4.3.4_KB-TZ_Expansion_Anchor_(316-327)r021a.pdf