412S AGRI JCB WHEELED LOADING SHOVEL

JCB WHEELED LOADING SHOVEL | 412S AGRI

MAX. ENGINE POWER: 97kW (130hp)

MAX. OPERATING WEIGHT: 8606kg (18973lb)

MAX. LOADER CAPACITY: 1.5m3 (2.0yd3)

A Productof Hard Work

9999/4960 8/08 Issue 5

JCB WHEELED LOADING SHOVEL |412S AGRI

A ProductofHard Work

mm (ft-in)

A Overall length with standard bucket 6196 (20-4)

B Axle to pivot pin 1278 (4-2)

C Wheel Base 2700 (8-10)

D Axle to counterweight face 1376 (4-6)

E Minimum ground clearance 400 (1-4)

F Height over exhaust 2820 (9-3)

G Width over cab 1310 (4-4)

H Width over tyres 2347 (7-8)

H1 Wheel track 1880 (6-2)

J Height over cab 2928 (9-7)

Data based on machine equipped with a 1.0m3 bucket with bolt-on toeplates and 460/70 R24 XMCL tyres.

STATIC DIMENSIONS

mm (ft-in)

Pin height (maximum) 3635 (11-11)

Overall operating height 4532 (14-10)

Front axle weight kg (lb) 3655 (8058)

Rear axle weight kg (lb) 3854 (8497)

Total weight kg (lb) 7637 (16837)

Inside radius 2310 (7-7)

Maximum radius 5306 (17-5)

Articulation angle degrees ±40°

LOADER DIMENSIONS – FORK FRAME WITH FORKS

Parallel fork Non parallel fork

Fork carriage width mm (ft-in) 1500 (4-11) 1500 (4-11)

Length of tines mm (ft-in) 1220 (4-0) 1220 (4-0)

A Reach at ground level mm (ft-in) 811 (2-8) 818 (2-8)

B Reach at arms horizontal mm (ft-in) 1531 (5-0) 1538 (5-1)

C Below ground level mm (ft-in) 27 (0-1) 37 (0-11⁄2)

D Arms, horizontal height mm (ft-in) 1718 (5-8) 1708 (5-7)

E Arms, maximum height mm (ft-in) 3449 (11-4) 3439 (11-3)

F Reach at maximum height mm (ft-in) 825 (2-8) 832 (2-9)

Payload* kg (lb) 2665 (5875) 2665 (5875)

Tipping load straight kg (lb) 3612 (7962) 3612 (7962)

Tipping load full turn (40°) kg (lb) 3056 (6738) 3056 (6738)

Attachment weight kg (lb) 440 (970) 440 (970)

Assumes the machine is fitted with Michelin 460/70 R24 XMCL tyres and the industrial quickhitch is used.*At the centre-of-gravity distance 500mm (1ft-51⁄2in). Based on 80% of full turn tipping load as defined by ISO 8313.Manual fork spacings at 50mm (2in) increments. Fork section 100mm x 50mm (4in x 2in).

JCBSales Limited, Rocester, Staffordshire ST14 5JP. Tel: 01889 590312. Fax: 01889 590588. Web: http://www.jcb.com

JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. TheJCB logo is a registered trademark ofJ C Bamford Excavators Ltd.

A GLOBAL COMMITMENT TO QUALITY

JCB’s total commitment to its products and customers has helped it grow from a one-man

business into Britain’s largest privately owned manufacturer of backhoe loaders, crawler excavators,

wheeled excavators, telescopic handlers, wheeled loaders, dump trucks, rough terrain fork lifts,

industrial fork lifts, mini/midi excavators, skid steer loaders, tractors and compaction equipment.

By making constant and massive investments in the latest production technology, theJCBfactories

have become some of the most advanced in the world.

By leading the field in innovative research and design, extensive testing and stringent quality control,

JCB machines have become renowned all over the world for performance, value and reliability.

And with a global sales and service network of more than 650 dealers and agents, we aim to deliver

the best customer support in the industry.

Through setting the standards by which others are judged, JCB has become one of the world’s

most impressive success stories.

Printed in the UK on paper made from sustainable forests. The pulp used in the manufacture of this paper is made fromrenewable timber produced on a fully sustainable basis, and is bleached without the use of chlorine gas (ECF –ElementalChlorine Free). This paper is suitable for recycling.

Bucket mounting Quickhitch Quickhitch Industrial Quickhitch Quickhitch Quickhitch Quickhitch

Bucket type General Purpose General Purpose General Purpose High Tip Manure/Silage Fork Manure/Silage Fork

Bucket equipment – – Reversible toeplate – – Top Grab

Bucket capacity (SAE heaped) m3 (yd3) 1.0 (1.30 1.2 (1.6) 1.0 (1.3) 1.5 (2.0) 2.5 (3.3) 1.9 (2.5)

Bucket capacity (struck) m3 (yd3) 0.840 (1.100) 1.009 (1.319) 0.840 (1.100) 1.200 (1.570) – –

Bucket width mm (ft-in) 2286 (7-6) 2286 (7-6) 2286 (7-6) 2400 (7-10) 2290 (7-6) 2290 (7-6)

Bucket weight kg (lb) 384 (845) 416 (915) 441 (970) 1250 (2756) 500 (1102) 595 (1312)

Maximum material density kg/m3 (lb/yd3) 1820 (4012) 1518 (3348) 1820 (4012) 918 (2024) – –

Tipping load straight kg (lb) 4289 (9455) 4296 (9472) 4289 (9455) 3244 (7152) 4674 (10305) 4551 (10033)

Tipping load full turn kg (lb) 3641 (8026) 3644 (8033) 3641 (8026) 2754 (6072) 3960 (8731) 3856 (8500)

Payload kg (lb) 1984 (4374) 1986 (4377) 1984 (4374) 1501 (3308) 2158 (4758) 2101 (4632)

Maximum break out force kN (lbf) 57.7 (12970) 57.7 (12970) 57.7 (12970) 36.5 (8204) – –

M Dump angle maximum degrees 47.5° 47.5° 47.5° 42.5° 47.5° 47.5°

N Roll back angle at full height degrees 59° 59° 59° 59° 59° 59°

O Roll back at carry degrees 49.5° 49.5° 49.5° 49.5° 49.5° 49.5°

P Roll back at ground level degrees 45° 45° 45° 45° 45° 45°

Q Load over height mm (ft-in) 3429 (11-3) 3429 (11-3) 3409 (11-2) 3517 (11-6) 3429 (11-3) 3429 (11-3)

R Dump height (45° dump) mm (ft-in) 2700 (8-10) 2700 (8-10) 2668 (8-9) 4081** (13-5) 2347 (7-8) 2347 (7-8)

S Dig depth mm (ft-in) 47 (0-2) 47 (0-2) 67 (0-2) 67 (0-2) 35 (0-1) 35 (0-1)

T Reach at dump height mm (ft-in) 1063 (3-6) 1063 (3-6) 1093 (3-7) 1575 (5-2) 1416 (4-7) 1416 (4-7)

Reach maximum (45° dump) mm (ft-in) 1812 (5-11) 1812 (5-11) 1844 (6-1) 2156 (7-1) 2165 (7-1) 2165 (7-1)

Operating weight (includes 80kg operator and full fuel tank) kg (lb) 7637 (16837) 7669 (16907) 7694 (16962) 8503 (18746) 7753 (17092) 7848 (17302)

Note: 1.0m3 = 1.308yd3 = 35.32ft3. 1kg = 2.205lb. 1kg/m3 = 1.686lb/yd3 = 0.062lb/ft3.*** Carriage rolled fully back, bucket fully dumped.

LOADER DIMENSIONS – Standard height arm CHANGES TO OPERATING PERFORMANCE AND DIMENSIONS

Tipping loads Dimensions

Op. Weight Straight Full Turn Vertical Width

Tyre size Manufacturer kg (lb) kg (lb) kg (lb) mm (in) mm (in)

500/70 R24 XMCL* Michelin +48 (106) +28 (62) +24 (53) +27 (1) +69 (2.7)

Additional counterweight +331 (728) +537 (1181) +445 (979) 0 0

Cast counterweight** +500 (1102) +811 (1788) +672 (1482) 0 0

** Not available with the hydraulic towhitch installation.*Machine track increases to 1880mm (6ft 2in)

4-cylinder wastegated turbo-charged, liquid cooled, direct injection common rail diesel. Air-to-air charge-air cooling ensure lowemissions and provides minimum fuel consumption. A remote sump oil drain facility simplifies servicing.

Type Diesel 4 stroke

Make JCB Dieselmax

Capacity litres (in3) 4.4 (269)

Bore mm (in) 103 (4.06)

Stroke mm (in) 132 (5.2)

Aspiration Turbocharged Aftercooled

Cylinders 4

Max gross power to SAE J1995/ISO 14396 kW (hp) @ 2200rpm 97 (130)

Rated gross power to SAE J1995/ISO 14396 kW (hp) @ 2200rpm 97 (130)

Nett power to SAE J1349/EEC 80/1269 kW (hp) @ 2200rpm 89 (119)

Max torque Nm (lbf.ft) @ 1300rpm 532 (392)

Emissions:- Relevant standards EUNR MM Stage 3 USA CFR Part 89 (Complies with EU/EPA “Off Highway” ConstructionEquipment Regulation Stage 3).

ENGINE

Widely spaced four ram geometry provides the combination of excellent visibility with high bucket torque characteristicsthroughout the working arc. The pin, bush and sealing design on all pivot points provide extended maintenance intervals.

LOADER

4 wheel drive, automatic smooth shift transmission electrically operated selector and gear change incorporating a speed inhibitorand modulation for smooth, responsive on-the-move direction and ratio changes. Single stage integral torque converter 6 forward and 3 reverse gears.

Type Smooth shift powershift

Make & model ZF 6WG 110

Torque converter stall ratio 2.3 : 1

Speeds for 460/70 R24 XMCL tyres Forward Reverse

1st gear kph (mph) 5.4 (3.4) 5.4 (3.4)

2nd gear kph (mph) 8.1 (5.0) 12.6 (7.8)

3rd gear kph (mph) 12.6 (7.8) 25.6 (15.9)

4th gear kph (mph) 18.6 (11.6) –

5th gear kph (mph) 25.6 (15.9) –

6th gear kph (mph) 36.2 (22.5) –

1st gear kph (mph) 5.6 (3.5) 5.6 (3.5)

2nd gear kph (mph) 8.5 (5.3) 13.2 (8.2)

3rd gear kph (mph) 13.2 (8.2) 26.7 (16.6)

4th gear kph (mph) 19.4 (12.1) –

5th gear kph (mph) 26.7 (16.6) –

6th gear kph (mph) 37.8 (23.5) –

TRANSMISSION

Priority steer hydraulic system with emergency steering. Gear pump meters flow through steer valve @ 200 bar (2900 lb/in2) toprovide smooth low effort response. Steering angle ± 40°. Steer rams located high in the chassis fabrication to provide protectionfrom damage. Adjustable steering column.

STEERING

460/70 R24 XMCL, 500/70 R24 XMCL.

Twin gear pumps with automaic unloader valve giving combination of speed and power on demand, making efficient use of enginepower available. Main services are servo actuated from a single lever (joystick) loader control. Auxiliary circuits controlled via additionallever or joystick mounted electrical buttons. Accumulator back-up is available to control loader in the event of loss of pump pressure.

Pump type Twin gear pumps

Pump 1 max. flow l/min (UK gal/min) 54 (11.9)

Pump 1 max. pressure bar (lb/in2) 220 (3190)

Pmp 2 max. pressure bar (lb/in2) 170 (2465)

Hydraulic cycle times at full engine revs seconds

Arms raise (full bucket) 4.6

Bucket dump (full bucket) 1.4

Arms lower (empty bucket) 3.0

Total cycle 9.0

Ram dimensions Bore Rod Closed centres Stroke

Bucket ram x2 mm (in) 80 (3.1) 50 (2) 1502 (59.1) 928 (36.5)

Lift ram x2 mm (in) 90 (3.5) 50 (2) 1107 (43.6) 742 (29.2)

Steer ram x2 mm (in) 60 (2.4) 30 (1.2) 621 (24.4) 312 (12.3)

LOADER HYDRAULICS

Hydraulic power braking on all wheels, operating pressure 50 bar (725psi). Dual circuit with accumulator back-up providemaximum safety under all conditions. In-board mounted, oil immersed, multi-plate disc brakes with organic brake linings areenvironmentally acceptable. Parking brake, mechanical disc type operating on transmission output shaft.

BRAKES

Type Limited slip differentials with epicyclic hub reduction

Make & model JCB PD70

Overall axle ratio 18.16 : 1

Rear axle oscillation 25°

Resiliently mounted ROPS/FOPS structure (tested in accordance with ISO 3471-1 : 1986 / ISO 3449 : 1984). De-luxe operatorenvironment combines ergonomically located controls with a high level of appointment and low internal noise levels. Entry/exit isvia large rear hinged door and anti-slip steps. Excellent forward visibility is provided by a 3 section curved, laminated windscreenand low waistline. Extensive instrumentation includes electronic monitoring panel and display (EMS). Heating / ventilation providesbalanced and filtered air distribution throughout the cab via a powerful 11 kW capacity heater. The unitary construction allows easysealing and prevents ingress of dust. A transmission lock on the selector prevents inadvertent engagement and the loader controlscan be isolated for safe road travel.

litres (UK gal)

Hydraulic system 110 (24.2)

Fuel tank 125 (27.5)

Engine oil sump 10.7 (2.35)

Transmission oil system 24 (5.2)

Axle oil (front) 25 (5.5)

Axle oil (rear) 25 (5.5)

Engine coolant system 21.5 (4.7)

SERVICE FILL CAPACITIES

An extensive range of attachments is available to users, covering the job requirements.

ATTACHMENTS

Loader: Bucket reset mechanism, loader arm kickout mechanism, loader control isolator, single lever servo control, high torquegeometry combines with excellent visibility between the arms.

Engine: Air cleaner – 2 stage dry type – cyclonic with primary and safety elements, stainless steel silencer and exhaust stack,sedimenter, twin bowl fuel filters, fan guards.

Transmission: Single lever shift control, speed inhibitor, neutral start, disconnect on footbrake and loader lever, disconnect isolatorswitch, direction changes and kickdown on gear selector and loader control lever.

Axles: Limited slip differentials, front and rear, epicyclic wheel hub reduction, fixed front, oscillating rear.

Brakes: Multi-plate wet disc brakes, organic linings, dual circuit hydraulic power assisted. Parking disc brake on transmission output shaft.

Hydraulics: Gear pumps with priority steer, emergency steer back-up, 2 spool loader circuit with accumulator support, 3rd spool auxiliary hydraulic circuit as standard. Hydraulic tank located in the rear chassis fabrication.

Steering: Adjustable steering column, “soft feel” steering wheel 5 turns lock to lock, resilient stops on max lock.

Cab: ROPS/FOPS safety structure, cigar lighter, ashtray, interior reading light, centre mounted master warning light. Electronicmonitoring panel with LCD message display. Two speed intermittent front windscreen wipe/wash and self park, single speed rearwindscreen wipe/wash and self park. 3 speed heater/demisting with replaceable air filter, LH and RH opening windows, sun visor,sun blind, internal rear view mirror, heated external mirrors, adjustable suspension seat with belt and headrest, operator storagefacilities, laminated windscreen, heated rear screen, loader control isolator, horn, 24V to 12V in cab converter.

Electrical: Road lights front and rear, parking lights, front and rear working lights, reverse alarm and light, rear fog light, batteryisolator, radio wiring and speakers, 55 amp alternator, rotating beacon.

Bodywork: Front fenders, side and rear access panels, flexible bottom step, recovery hitch, lifting lugs.

STANDARD EQUIPMENT

Auxiliary 4th spool hydraulic service, air conditioning, additional counterweight, oil bath air cleaner, turbo 2 pre-cleaner, visibowlpre-cleaner, tooth guard, replaceable bucket wearparts, sealed alternator, epoxy coated radiator/coolers, stainless steel brake pipes,Smooth ride system (SRS), hydraulic quickhitch, rear fenders, reversing camera (colour), auto greasing system, auxiliary controlbuttons on joystick, spark arrestor, front chassis apron mat, bolt on 100L (22 UK gal) auxiliary fuel tank, hydraulic towhitch, 12V or24V trailer electrics, trailer braking, fire extinguisher, number plate light kit, additional front and rear worklights.

OPTIONAL EQUIPMENT

24 volt negative ground system, 55 Amp alternator with 2 x 126 Amp hour low maintenance batteries. Isolator located in rearof machine. Ignition key start/stop and pre-heat cold start. Primary fuse box. Other electrical equipment includes quartz halogen,twin filament working lights, front/rear wash/wipe, heated rear screen, full road going lights, clock, gauge and warning lightmonitoring. In cab 24V to 12V converter for radio feed, cigar lighter plus spare feed. Connectors to IP67 standard.

ELECTRICAL SYSTEM

System voltage Volt 24

Alternator output Amp 55

Battery capacity Amp hour 2 x 126

Payload kg (lb) 1984 (4374) 1986 (4377) 1984 (4374) 1501 (3308) 2158 (4758) 2101 (4632)

500/70 R24 XMCL* Michelin +48 (106) +28 (62) +24 (53) +27 (1) +69 (2.7)

Make JCB Dieselmax

Bore mm (in) 103 (4.06)

Cylinders 4

ENGINE

LOADER

1st gear kph (mph) 5.4 (3.4) 5.4 (3.4)

2nd gear kph (mph) 8.1 (5.0) 12.6 (7.8)

3rd gear kph (mph) 12.6 (7.8) 25.6 (15.9)

4th gear kph (mph) 18.6 (11.6) –

5th gear kph (mph) 25.6 (15.9) –

6th gear kph (mph) 36.2 (22.5) –

1st gear kph (mph) 5.6 (3.5) 5.6 (3.5)

2nd gear kph (mph) 8.5 (5.3) 13.2 (8.2)

3rd gear kph (mph) 13.2 (8.2) 26.7 (16.6)

4th gear kph (mph) 19.4 (12.1) –

5th gear kph (mph) 26.7 (16.6) –

6th gear kph (mph) 37.8 (23.5) –

TRANSMISSION

STEERING

460/70 R24 XMCL, 500/70 R24 XMCL.

Total cycle 9.0

Bucket ram x2 mm (in) 80 (3.1) 50 (2) 1502 (59.1) 928 (36.5)

Lift ram x2 mm (in) 90 (3.5) 50 (2) 1107 (43.6) 742 (29.2)

Steer ram x2 mm (in) 60 (2.4) 30 (1.2) 621 (24.4) 312 (12.3)

LOADER HYDRAULICS

BRAKES

litres (UK gal)

ATTACHMENTS

STANDARD EQUIPMENT

OPTIONAL EQUIPMENT

ELECTRICAL SYSTEM

Payload kg (lb) 1984 (4374) 1986 (4377) 1984 (4374) 1501 (3308) 2158 (4758) 2101 (4632)

500/70 R24 XMCL* Michelin +48 (106) +28 (62) +24 (53) +27 (1) +69 (2.7)

Make JCB Dieselmax

Bore mm (in) 103 (4.06)

Cylinders 4

ENGINE

LOADER

1st gear kph (mph) 5.4 (3.4) 5.4 (3.4)

2nd gear kph (mph) 8.1 (5.0) 12.6 (7.8)

3rd gear kph (mph) 12.6 (7.8) 25.6 (15.9)

4th gear kph (mph) 18.6 (11.6) –

5th gear kph (mph) 25.6 (15.9) –

6th gear kph (mph) 36.2 (22.5) –

1st gear kph (mph) 5.6 (3.5) 5.6 (3.5)

2nd gear kph (mph) 8.5 (5.3) 13.2 (8.2)

3rd gear kph (mph) 13.2 (8.2) 26.7 (16.6)

4th gear kph (mph) 19.4 (12.1) –

5th gear kph (mph) 26.7 (16.6) –

6th gear kph (mph) 37.8 (23.5) –

TRANSMISSION

STEERING

460/70 R24 XMCL, 500/70 R24 XMCL.

Total cycle 9.0

Bucket ram x2 mm (in) 80 (3.1) 50 (2) 1502 (59.1) 928 (36.5)

Lift ram x2 mm (in) 90 (3.5) 50 (2) 1107 (43.6) 742 (29.2)

Steer ram x2 mm (in) 60 (2.4) 30 (1.2) 621 (24.4) 312 (12.3)

LOADER HYDRAULICS

BRAKES

litres (UK gal)

ATTACHMENTS

STANDARD EQUIPMENT

OPTIONAL EQUIPMENT

ELECTRICAL SYSTEM

MAX. ENGINE POWER: 97kW (130hp)

MAX. OPERATING WEIGHT: 8606kg (18973lb)

MAX. LOADER CAPACITY: 1.5m3 (2.0yd3)

9999/4960 8/08 Issue 5

mm (ft-in)

A Overall length with standard bucket 6196 (20-4)

B Axle to pivot pin 1278 (4-2)

C Wheel Base 2700 (8-10)

D Axle to counterweight face 1376 (4-6)

E Minimum ground clearance 400 (1-4)

F Height over exhaust 2820 (9-3)

G Width over cab 1310 (4-4)

H Width over tyres 2347 (7-8)

H1 Wheel track 1880 (6-2)

J Height over cab 2928 (9-7)

Data based on machine equipped with a 1.0m3 bucket with bolt-on toeplates and 460/70 R24 XMCL tyres.

STATIC DIMENSIONS

mm (ft-in)

Pin height (maximum) 3635 (11-11)

Overall operating height 4532 (14-10)

Front axle weight kg (lb) 3655 (8058)

Rear axle weight kg (lb) 3854 (8497)

Total weight kg (lb) 7637 (16837)

Inside radius 2310 (7-7)

Maximum radius 5306 (17-5)

Articulation angle degrees ±40°

Parallel fork Non parallel fork

Fork carriage width mm (ft-in) 1500 (4-11) 1500 (4-11)

Length of tines mm (ft-in) 1220 (4-0) 1220 (4-0)

A Reach at ground level mm (ft-in) 811 (2-8) 818 (2-8)

B Reach at arms horizontal mm (ft-in) 1531 (5-0) 1538 (5-1)

C Below ground level mm (ft-in) 27 (0-1) 37 (0-11⁄2)

D Arms, horizontal height mm (ft-in) 1718 (5-8) 1708 (5-7)

E Arms, maximum height mm (ft-in) 3449 (11-4) 3439 (11-3)

F Reach at maximum height mm (ft-in) 825 (2-8) 832 (2-9)

Payload* kg (lb) 2665 (5875) 2665 (5875)

Tipping load straight kg (lb) 3612 (7962) 3612 (7962)

Tipping load full turn (40°) kg (lb) 3056 (6738) 3056 (6738)

Attachment weight kg (lb) 440 (970) 440 (970)

Assumes the machine is fitted with Michelin 460/70 R24 XMCL tyres and the industrial quickhitch is used.*At the centre-of-gravity distance 500mm (1ft-51⁄2in). Based on 80% of full turn tipping load as defined by ISO 8313.Manual fork spacings at 50mm (2in) increments. Fork section 100mm x 50mm (4in x 2in).

JCBSales Limited, Rocester, Staffordshire ST14 5JP. Tel: 01889 590312. Fax: 01889 590588. Web: http://www.jcb.com

JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. TheJCB logo is a registered trademark ofJ C Bamford Excavators Ltd.

By making constant and massive investments in the latest production technology, theJCBfactories

Printed in the UK on paper made from sustainable forests. The pulp used in the manufacture of this paper is made fromrenewable timber produced on a fully sustainable basis, and is bleached without the use of chlorine gas (ECF –ElementalChlorine Free). This paper is suitable for recycling.

MAX. ENGINE POWER:97kW (130hp)

MAX. OPERATING WEIGHT:8606kg (18973lb)

MAX. LOADER CAPACITY:1.5m3(2.0yd3)

9999/4960 8/08 Issue 5

mm (ft-in)

AOverall length with standard bucket6196 (20-4)

BAxle to pivot pin1278 (4-2)

CWheel Base2700 (8-10)

DAxle to counterweight face1376 (4-6)

EMinimum ground clearance400 (1-4)

FHeight over exhaust2820 (9-3)

GWidth over cab1310 (4-4)

HWidth over tyres2347 (7-8)

H1Wheel track1880 (6-2)

JHeight over cab2928 (9-7)

Data based on machine equipped with a 1.0m3bucket with bolt-on toeplates and 460/70 R24 XMCL tyres.

STATIC DIMENSIONS

mm (ft-in)

Pin height (maximum)3635 (11-11)

Overall operating height4532 (14-10)

Front axle weightkg (lb)3655 (8058)

Rear axle weightkg (lb)3854 (8497)

Total weightkg (lb)7637 (16837)

Inside radius2310 (7-7)

Maximum radius5306 (17-5)

Articulation angledegrees±40°

Parallel forkNon parallel fork

Fork carriage widthmm (ft-in)1500 (4-11)1500 (4-11)

Length of tinesmm (ft-in)1220 (4-0)1220 (4-0)

AReach at ground levelmm (ft-in)811 (2-8)818 (2-8)

BReach at arms horizontalmm (ft-in)1531 (5-0)1538 (5-1)

CBelow ground levelmm (ft-in)27 (0-1)37 (0-11⁄2)

DArms, horizontal heightmm (ft-in)1718 (5-8)1708 (5-7)

EArms, maximum heightmm (ft-in)3449 (11-4)3439 (11-3)

FReach at maximum heightmm (ft-in)825 (2-8)832 (2-9)

Payload*kg (lb)2665 (5875)2665 (5875)

Tipping load straightkg (lb)3612 (7962)3612 (7962)

Tipping load full turn (40°)kg (lb)3056 (6738)3056 (6738)

Attachment weightkg (lb)440 (970)440 (970)

Assumes the machine is fitted with Michelin 460/70 R24 XMCLtyres and the industrial quickhitch is used.*At the centre-of-gravity distance 500mm (1ft-51⁄2in). Based on 80% of full turn tipping load as defined by ISO 8313.Manual fork spacings at 50mm (2in) increments. Fork section 100mm x 50mm (4in x 2in).

JCB Sales Limited, Rocester, Staffordshire ST14 5JP. Tel: 01889 590312. Fax: 01889 590588. Web: http://www.jcb.com

JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. The JCB logo is a registered trademark of J C Bamford Excavators Ltd.

By making constant and massive investments in the latest production technology, the JCB factories

Printed in the UK on paper made from sustainable forests. The pulp used in the manufacture of this paper is made fromrenewable timber produced on a fully sustainable basis, and is bleached without the use of chlorine gas (ECF – ElementalChlorine Free). This paper is suitable for recycling.

412S AGRI JCB WHEELED LOADING SHOVEL

Documents

Transcript of 412S AGRI JCB WHEELED LOADING SHOVEL