4. 디지털 지시계기 Digital indicator * 각종 입력 신호를 받아 User 가 원하는...
description
Transcript of 4. 디지털 지시계기 Digital indicator * 각종 입력 신호를 받아 User 가 원하는...
1
4. 디지털 지시계기
Digital indicator
* 각종 입력 신호를 받아 User 가 원하는 지시값을 표시하는 계기 .
( 교류 전류 . 전압은 물론 계장용 신호 , 어떠한 입력조건에서도 동작 가능함 )
특징
Display 값 임의로 조정가능
(Free Set 기능 내장 )
자동 입력 방식으로 타 신호의 영향이 없음
surge 대책 회로 채택
(1.2/50sec 5kV)
내부 TRANSFORMER 모두 12 차측 완전 절연 처리로 노이즈 방지 강화
FREE VOLTAGE 채택으로 사용 용이
2
PERMISSIBLE OVER-RANGE : 150% for 10 seconds of 120% continuously
INPUT : 0.3VA or Less
MODEL & SUFFIX CODE
HD-1100MODEL
ORDERING INFORMATIONSpecify code number and variables * Code number : HD-1100-INPUT-digit ex) HD-1100-1-A
* Special input range (code O)
GENERAL SPECIFICATIONSConstruction : panel flush mountingConnection : connectorHousing materiel : ivory plasticInput configuration : single-endedA/D conversion : dual-slope integration with automatic zero correction
PERFORMANCE Accuracy Voltage input : 0.1% of rag 1digit (0.1% of rag 2digit for 0.2V range) Current input : 0.2% of rag 1digit Temp coefficient : 0.05% of rag 1digit/ Line Voltage effect : 1digit of 10% change
INSTALLATIONPower supply : Ac rating (100-240) 10% 60/50HZ 6.0VAOperating temperature : 0 to +55 (32 to 131)Operating humidity : 20-85%RH (non-condensing)Storage temperature : -20 to +70 (-4 to +158)Storage humidity : 20-95%RH (non-condensing)Size : W96H48 D95Weight :
INPUT A DC 4 - 20mA
DC 0 - 1mA B DC 0 - 10mA C AC 0 - 1A D AC 0 - 5A E Specify order O
1 DC 0 - 50mV DC 0 - 1.999V 2 DC 0 - 19.99V 3 DC 0 - 300V 4 AC 0 - 1.999V 5 AC - 300V 6 O
DISPLAY DIGIT
1 3½ digit
2 4 digit
O Specify order (3digit to 4½ digit)
DISPLAYLED : 7-segment (0.56 Inch), red.Number of display : 3 or 4digitScaling factor for process Meter Zero : 0 1000 counts Span : Zero point + 50 to 1999 or 9999 counts.Decimal point position : 3 Positions seled alde by a jumper at pin connectorRead rate : 2.5/s standardDisplay HOLD : available by external in-put singnal
2
1
INPUT INPUT : 0 ~ 199.9V or 0 ~ 500V (MAX)
HD DIGITAL METER SERIES
DIGITAL PANEL INDICATOR MODEL HD - 1100
3
INSTALLATION INSTRUCTION Insulation resistance : 100M or more
with 500V DC Dielectric strength : 1200V AC 1minute (Input to power to gnd)
CONNECTOR PIN ASSIGNMENT
NO1 : +
NO2 :
NO3 : -
NO4 : +
NO5 : -
INPUT
DECIMAL POINT POSITION
Remove the jumper as follows
DP1(101)LED ON
DP2(102)LED ON
DP3(103)LED ON
1 2 3 4 5 6 7 8
NO6 : 220V
NO7 : 110V
NO8 : 0V
PANEL CUT OUT [Scale : mm] Panel thickness : 0.5 + 0.5mm
92+0.5
0.0
45
-0.5
0.0
DEMENSINS [Scale : mm]
96
48
12
91
12
11
5
44
4
HD DIGITAL METER SERIES
PROGRAMMABLE INDICATOR MODEL HD - 1200
MODEL & SUFFIX CODE
ORDERING INFORMATIONSpecify code number and variables * Code number : HD-1200-INPUT ex) HD-1200-1
* Special input range (code O&S)
GENERAL SPECIFICATIONSConstruction : panel flush mountingConnection : screw terminalsHousing materiel : ivory plastic (ABS)Input configuration : single-endedA/D conversion : dual-slope integration with automatic zero correctionScalling : programmable scaling Key S/W INPUT setting
INSTALLATIONPower supply : Ac rating (100-240) 10% 60/50HZ 6.0VAOperating temperature : 0 to +55 (32 to 131)Operating humidity : 20-85%RH (non-condensing)Storage temperature : -20 to +70 (-4 to +158)Storage humidity : 20-95%RH (non-condensing)Size : W96H48 D118Weight :
DISPLAYLED : 7-segment (0.56 Inch), red and greenNumber of display : 4digitScaling factor for process Meter Zero : adjustable by internal selector switch with each range of -9999 to 0 or 0 to 1000 or 0 to 9999 Span : Zero point to 9999 coungs.Decimal point position : programmable adiustable by interwal selector switchRead rate : 2.5/s standardDisplay HOLD : available by external in-put singnalOver-range indication : display flashes-F
INPUT
INPUT INPUT IMPEDANCE
0 ~ 10V0 ~ 5V1 ~ 5V
±19.99V±199.9V
1M Ω or more1M Ω or more1M Ω or more
10M Ω or more10M Ω or more
4 ~ 20mA0 ~ 20mA0 ~ 5mA0 ~ 1mA
250 Ω100 Ω200 Ω
1K
Rt 100 Ω JPt 100 100 Ω, Pt 100 100 Ω (Din)
HD-1200
MODEL
Power
Input
Output
A DC 4~20mA
V DC 0~10V
C DC 0~5V
R RTD(PT100Ω )
P Potentiometer
S Spec Other
1 Alarm Output2(H/L)
2 Alarm Output4(H/HH/L/LL)
3 Analog Output 2Alarm(H/L)
4 Analog Output 4Alarm(H/HH/L/LL)
5 Spec Other
X AC 110/220V/50~60Hz
Y DC 24V
PERFORMANCE
Accuracy Voltage input : 0.1% of rag 1digit (0.1% of rag 2digit for 0.2V range) Current input : 0.2% of rag 1digit Temp coefficient : 0.05% of rag 1digit/ Line Voltage effect : 1digit of 10% change Dielctric strength : 1500V AC 1 minute (Input to power)
5
INSTALLATION INSTRUCTION
CONNECTOR PIN ASSIGNMENT
PANEL CUT OUT [Scale : mm] Panel thickness : 0.5 + 0.5mm
DIMENSION [Scale : mm]
결선도 - 2ALARM 인 경우
1 2 3 4 5 6 7 8 A B b + - - SUP
+ - 220V 110V 0V
INPUT OUTPUT POWER
9 10 11 12 13 14 15 16 NO NC COM NO NC COM
AL1 AL2
9 10 11 12 13 14 15 16 NO COM NO COM NO COM NO COM
AL1 AL2 AL3 AL4
- 4ALARM 인 경우
- INPUT & ANALOG OUTPUT & POWER
1 2 3 4 5 6 7 8 A B b + - - SUP
+ - 220V 110V 0V
INPUT OUTPUT POWER
- INPUT & ANALOG OUTPUT & POWER
6
7
8
9
HD DIGITAL METER SERIES
PROGRAMMABLE INDICATOR MODEL HD – 1200C
MODEL & SUFFIX CODE
ORDERING INFORMATIONSpecify code number and variables * Code number : HD-1200-INPUT ex) HD-1200-1
* Special input range (code O&S)
GENERAL SPECIFICATIONSConstruction : panel flush mountingConnection : screw terminalsHousing materiel : ivory plastic (ABS)Input configuration : single-endedA/D conversion : dual-slope integration with automatic zero correctionScalling : programmable scaling Key S/W INPUT setting
INSTALLATIONPower supply : Ac rating (100-240) 10% 60/50HZ 6.0VAOperating temperature : 0 to +55 (32 to 131)Operating humidity : 20-85%RH (non-condensing)Storage temperature : -20 to +70 (-4 to +158)Storage humidity : 20-95%RH (non-condensing)Size : W96H48 D118Weight :
DISPLAY
LED : 0.56inch 7-segment, red or greenNumber of display digits : 6(0~999999 c/h)Decimal point position : 3 position selectable by function key at the front panelIntegration range : user changeable by function key at the front panel Engineering unit indication : sticker attached
INPUT
INPUT INPUT IMPEDANCE
0 ~ 10V0 ~ 5V1 ~ 5V
±19.99V±199.9V
1M Ω or more1M Ω or more1M Ω or more
10M Ω or more10M Ω or more
4 ~ 20mA0 ~ 20mA0 ~ 5mA0 ~ 1mA
250 Ω100 Ω200 Ω
1K
Rt 100 Ω JPt 100 100 Ω, Pt 100 100 Ω (Din)
HD-1200C
MODEL
Power
Input
Output
A Dry- Contact
V Open- Collector
C Voltage Pulse
R Current Pulse
S Spec Order
1 Alarm Output1
X AC 110/220V/50~60Hz
Y DC 24V
PERFORMANCE
Accuracy Voltage input : 0.1% of rag 1digit (0.1% of rag 2digit for 0.2V range) Current input : 0.2% of rag 1digit Temp coefficient : 0.05% of rag 1digit/ Line Voltage effect : 1digit of 10% change Dielctric strength : 1500V AC 1 minute (Input to power)
10
INSTALLATION INSTRUCTION
CONNECTOR PIN ASSIGNMENT
PANEL CUT OUT [Scale : mm] Panel thickness : 0.5 + 0.5mm
DIMENSION [Scale : mm]
결선도
1 2 3 4 5 6 7 8 A B b + - - SUP
+ - 220V 110V 0V
INPUT OUTPUT POWER
- INPUT & ANALOG OUTPUT & POWER
11
RTD INPUT 2 or 3 wire RTD’S input sensing : 2mA DC(pt)
MODEL & SUFFIX CODE
HD-GPMAMODEL
ORDERING INFORMATIONSpecify code number and variables * Code number : HD-GPMA-INPUT ex) HD-GMPA-A
* Special input range (code O)
GENERAL SPECIFICATIONSConstruction : Mosaic graphic panel flush mounting
Connection : PIN connector
Housing materiel : black plastic
Input configuration : single-ended
Scaling : microprocessor using
control for key s/w
INSTALLATIONPower supply : DC : 15~24V 10% 75mA at 24V INPUT AC : rating (20-30V) 10% 60/50HZ 20VAOperating temperature : 0 to 55 (33 to 131)Operating humidity : 20-85%RH (non-condensing)Storage temperature : -20 to 70 Storage humidity : 20-95%RH (non-condensing)Size : W75H25 D105mmWeight : about 200g
INPUT
A 4 ~ 20mA DC B 1 ~ 5V DC C RTD INPUT D PF DISPLAY (- 0.5 ~ 1 ~ 0.5) O Spec Order
DISPLAYLED : 7-segment (0.56 Inch), red and greenNumber of display digit : 4digitScaling factor for process Meter Zero : 0 -1999 counts Span : (Zero point) + 9999 counts.
Decimal point position : at key s/w seltingRead rate : 1.2/sec standardOver-range indication : display by -F
INPUT DC INPUT
INPUT INPUT IMPEDANCE1.999V19.99V199.9V
10M or more
4 ~ 20mA0 ~ 20mA0 ~ 1mA
100M
100M
1 K
USABLE RANGEINPUT
J pt 100pt 100/J ISpt 100/DIN
- 200 TO 500- 200 TO 600- 200 TO 600
- 328 TO 932- 328 TO 1112- 328 TO 1112
HD DIGITAL METER SERIES
PROGRAMMABLE MOSAIC INDICATORMODEL HD - GPMA
※ 당사는 GPMA 를 INPUT & POWER 완전 절연 제품만 제작 판매함 .(ISOLATION 방식 )
12
BLOCK DIAGRAM
* OPERATION 1
250.0
HrAn 500.0 400.0 200.0
F1F1 F1
F2
F1 F2
F1
F2
* 현재의 HIGH RANGE 지시 : 자리이동
: 숫자변경
* NORMAL 상태
LrAn 0.0 100.0 350.0
F1F1 F1
F2
F1 F2
F1
F2
* 현재의 LOW RANGE 지시 : 자리이동
: 숫자변경
* NORMAL 상태
OFFS 0.0 - 0.5 249.5
F1F1 F1
F2
F1 F2
F1
F2
* 현재의 OFFSET 지시 : 자리이동
: 숫자변경
* NORMAL 상태
dp_S 888.8 88.88 250.0
F1F1 F1
F2
F1 F2
F2* 현재의 소숫점 지시 : 소숫점이동 * NORMAL 상태
LCUL OFF 0n 250.0
F1F1 F1
F2
F1 F2
F2* 현재의 LOW LIMIT 지시 : 상태 변경 * NORMAL 상태
250.0
F1
* NORMAL 상태
* NORMAL 상태
LOW
DR
IFT
AM
PLI
FIE
R
A/D
CO
NV
ER
TER
MICROPROCESSOR
DISPLAYDRIVER
RANGEPROCESSOR
AC&DC/DCPOWER
CONVERTER
1
2
3
54P
OW
ER
INP
UT
+
-
-+
13
PERFORMANCE
DIMENSION
Accuracy 0.2% of rSg 1digit Temp coefficient : 0.005% of rag 1digit/ Line Voltage effect : 1digit of 10% change
Insulation resistance : 100M or more
with 500V DC Dielectric strength : 1200V AC 1minute (Input to power to gnd)
TERMINAL CONNECTION
NO1 : +
NO2 : -
NO3 : COM
NO4 : -
NO5 : +
INPUT
POWER
A
B
b’
RTD
1 2 3 4 5
75
95
91
5
15
22
25
MODE 설명
1. HIGH RANGE SET MODE HrAn ① DISPLAY RANGE 의 HIGH 값을 설정하는 MODE 이다 .
② SETTING RANGE : 0-9999
③ DEFAULT SET VALUE : 1000
2. LOW RANGE SET MODE LrAn ① DISPLAY RANGE 의 LOW 값을 설정하는 MODE 이다 .
② SETTING RANGE : -1999 - (+)9999
③ DEFAULT SET VALUE : 0
3. OFFSET SET MODE OFFS ① NORMAL MODE 에서 실재값과 DISPLAY 값이 맞지
않을 때 SETTING 하는 값 보정 MODE 이다 .
② 예 1> 실재값 : 150.0 DISPLAY 값 : 150.3
OFFSET SETTING 값 : -0.3
예 2> 실재값 : 1500 DISPLAY 값 : 1495
OFFSET SETTING 값 : -0.5
※ DISPLAY 값 = DISPLAY + OFFSET 값
③ DEFAULT SET VALUE : 0
4. 소숫점 변경 MODE dP_S ① 소숫점을 변경하는 MODE
5. LOW LIMIT SET MODE LCUE ① DISPLAY RANGE 의 LOW 값 이하로 값이 내려가지
않게 ZERO LIMIT 기능을 가능 또는 불가능하게 하는
MODE 이다 .
② ON : ZERO LIMIT ENABLE.
OFF : ZERO LIMIT DISABLE.
* OPERATION 2
14
MODEL & SUFFIX CODE
HD-GPMCMODEL
ORDERING INFORMATION* Code number : HD-GPMC-INPUT ex) HD-GPMC-A
GENERAL SPECIFICATIONSConstruction : Mosaic graphic panel flush mountingConnection : PIN connectorHousing materiel : black plastic
INSTALLATIONPower supply : DC : 15~24V 10% 75mA at 24V INPUT AC : rating (20-30V) 10% 60/50HZ 20VAOperating temperature : 0 to 55 (33 to 131)Operating humidity : 20-85%RH (non-condensing)Storage temperature : -20 to 70 Storage humidity : 20-95%RH (non-condensing)Mounting : Mosaic graphic panel flush mountingsSize : W75H25 D105mmWeight : about 200g
INPUT
A Dry contact
B Open collector
C Voltage pulse
DISPLAYLED : 7-segment (10.16mm), red and greenNumber of display digit : 6digitMemorize the indication value of power failure before stateReset method : key s/wData HOLD : EPROM TYPEData HOLDER TIME : about 10 year
INPUT TTL OR VOLTAGE PULSE
DRY CONTACT
OPEN Collector
INPUT FREQUINCY RANGE : 2KHX(MAX)
HD DIGITAL METER SERIES
MOSAIC COUNTER MODEL HD - GPMC
+-
COM
HD-GPMC
IN
500mV p-p to 50V p-p
HL
HD-GPMC
IN +-
COM
IN+-
COM
DC 12V at 3mA
※ 당사는 GPMC 를 INPUT & POWER 완전 절연 제품만 제작 판매함 .(ISOLATION 방식 )
15
PERFORMANCE
Accuracy 0.5% of rag 2digit
Temp coefficient : 0.005% of rag 1digit
Line Voltage effect : 1digit of 10% change
Insulation resistance : 100M or more
with 500V DC
Dielectric strength : 1200V AC 1minute
(Input to power)
TERMINAL CONNECTION
NO1 : +
NO2 : -
NO2
NO3
INPUT
RESET
NO4 : -
NO5 : +POWER
1 2 3 4 5
DIMENSION
16
SPECIFICATION
Power : DC 24V ± 5%Input Signal : RS – 485 SERIALDisplay: 4 DIGIT LED (H:10.16mm)
Address Selection : POWER TO INPUTIsolation: POWER TO INPUT
HD DIGITAL METER SERIES
COMMUNICATION MOSAIC INDICATORMODEL HD - GPMS
COMMUNICATION PROTOCOL
Communication : SIMPLEX
Baud Rate : 1200, 2400, 4800, 9600, 19200 BPS
(PROGRAM SETTING)
Start Bit : 1 BIT
Data Bit : 8 BIT
Parity Check : NONE
Stop Bit : 1 BIT
Address
Transmission Code : ASCII CODE (HEX)
Point : PROGRAM SETTING
Error Time : 1 ~ 55sec, 01 = Infinitely)
(PROGRAM SETTING)
MODEL & SUFFIX CODE
HD-GPMSMODEL
ORDERING INFORMATION
Specify code number and variables
* Code number : HD-GPMS-INPUT
ex) HD-GPMS-A
* Special input range (code O)
GENERAL SPECIFICATIONS
Construction : Mosaic graphic panel flush mounting
Connection : PIN connector
Housing materiel : black plastic
Input configuration : single-ended
Scaling : microprocessor using
control for key s/w
INPUT
A RS 485 B RS 422 (주문사항) C RS 232 (주문사항)
DISPLAY
LED : 7-segment (H:0.56 Inch), red and green
Number of display digit : 4digit
Scaling factor for process Meter
Zero : 0 -1999 counts
Span : (Zero point) + 9999 counts.
Decimal point position : at key s/w selting
Read rate : 1.2/sec standard
Over-range indication : display by -F
17
PERFORMANCE
Accuracy 0.5% of rag 2digit
Temp coefficient : 0.005% of rag 1digit
Line Voltage effect : 1digit of 10% change
Insulation resistance : 100M or more
with 500V DC
Dielectric strength : 1200V AC 1minute
(Input to power)
TERMINAL CONNECTION
NO1 : +
NO2 : -
NO2
NO3
INPUT
RESET
NO4 : -
NO5 : +POWER
1 2 3 4 5
DIMENSION
18
1. HARD WARE ??
a) CPU : ONE-CHIP MICRO PROCESSOR (ATMEL AT89C52)b) COMMUNICATION : RS-422 or RS-485 (RECEIVE ONLY)c) BAUD RATE : 2400bps ~ 38400bpsd) ADDRESS : 0 ~ 999e) DISPLAY : RED COLOR STANDARD 4 DIGIT : -999 ~ 9999 6 DIGIT : 0 ~ 999999f) PROTOCOL : ?? PROTOCOLi)???? : MAX 1.5VA
2. ??
a) ADDRESS? ???? KEY? ?????? ( Addr )b) BAUD RATE? ???? KEY? ?????? ( bAUr )c) ???? ???? KEY? ?????? ( _dp _ )d) SERIAL INPUT 가 20sec 이상 검지되지 않을 때 자동적으로 DISPLAY
는 CLEAR 된다 .
3. INDICATOR 결선 방법
RX+
RX-
-
+
RXD
POWER
RX-RX+ P- P+
#0 #1 #63
RX+ RX- P- P+ RX+ RX- P- P+
19
4. KEY
SETTING ??
20
5.4
DIGIT
21
6.6
DIGIT
22
SPECIFICATION
Power : DC 24V ± 5%Input Signal : RS – 485 SERIALDisplay: 4 DIGIT LED (H:10.16mm)
Address Selection : POWER TO INPUTIsolation: POWER TO INPUT
HD DIGITAL METER SERIES
COMMUNICATION MOSAIC INDICATORMODEL HD - GPMSC
COMMUNICATION PROTOCOL
Communication : SIMPLEX
Baud Rate : 1200, 2400, 4800, 9600, 19200 BPS
(PROGRAM SETTING)
Start Bit : 1 BIT
Data Bit : 8 BIT
Parity Check : NONE
Stop Bit : 1 BIT
Address
Transmission Code : ASCII CODE (HEX)
Point : PROGRAM SETTING
Error Time : 1 ~ 55sec, 01 = Infinitely)
(PROGRAM SETTING)
MODEL & SUFFIX CODE
HD-GPMSC
MODEL
ORDERING INFORMATION
Specify code number and variables
* Code number : HD-GPMSC-INPUT
ex) HD-GPMSC-A
* Special input range (code O)
GENERAL SPECIFICATIONS
Construction : Mosaic graphic panel flush mounting
Connection : PIN connector
Housing materiel : black plastic
Input configuration : single-ended
Scaling : microprocessor using
control for key s/w
INPUT
A RS 485 B RS 422 (주문사항) C RS 232 (주문사항)
DISPLAY
LED : 7-segment (H:10.41mm), red and green
Number of display digit : 4digit
Scaling factor for process Meter
Zero : 0
Span : (Zero point) 999999
Decimal point position : at key s/w selting
Read rate : 1.2/sec standard
Over-range indication : display by -F
23
PERFORMANCE
Accuracy 0.5% of rag 2digit
Temp coefficient : 0.005% of rag 1digit
Line Voltage effect : 1digit of 10% change
Insulation resistance : 100M or more
with 500V DC
Dielectric strength : 1200V AC 1minute
(Input to power)
TERMINAL CONNECTION
NO1 : +
NO2 : -
NO2
NO3
INPUT
RESET
NO4 : -
NO5 : +POWER
1 2 3 4 5
DIMENSION