3GPP TS 34.121-1 - 株式会社QT · Testing, UMTS 3GPP Postal address 3GPP support office address...

3GPP TS 34.121-1 V7.2.0 (2006-10)Technical Specification

3rd Generation Partnership Project;Technical Specification Group Radio Access Network;

User Equipment (UE) conformance specification;Radio transmission and reception (FDD);

Part 1: Conformance specification(Release 7)

The present document has been developed within the 3rd Generation Partnership Project (3GPP TM) and may be further elaborated for the purposes of 3GPP. The present document has not been subject to any approval process by the 3GPP Organizational Partners and shall not be implemented. This Specification is provided for future development work within 3GPP only. The Organizational Partners accept no liability for any use of this Specification.Specifications and reports for implementation of the 3GPP TM system should be obtained via the 3GPP Organizational Partners' Publications Offices.

Release 7 2 3GPP TS 34.121-1 V7.1.0 (2006-06)

Keywords Testing, UMTS

3GPP

Postal address

3GPP support office address 650 Route des Lucioles - Sophia Antipolis

Valbonne - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Internet http://www.3gpp.org

Copyright Notification

No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.

2006, 3GPP Organizational Partners (ARIB, ATIS, CCSA, ETSI, TTA, TTC).

All rights reserved.

http://www.3gpp.org/

Release 7 3 3GPP TS 34.121-1 V7.1.0 (2006-06)

Contents Foreword ..........................................................................................................................................................24 Introduction ......................................................................................................................................................24 1 Scope ......................................................................................................................................................25 2 References ..............................................................................................................................................25 3 Definitions, symbols, abbreviations and equations ................................................................................26 3.1 Definitions ....................................................................................................................................................... 26 3.2 Symbols ........................................................................................................................................................... 27 3.3 Abbreviations................................................................................................................................................... 27 3.4 Equations ......................................................................................................................................................... 28 4 Frequency bands and channel arrangement............................................................................................29 4.1 General............................................................................................................................................................. 29 4.2 Frequency bands .............................................................................................................................................. 29 4.3 TXRX frequency separation .......................................................................................................................... 30 4.4 Channel arrangement ....................................................................................................................................... 30 4.4.1 Channel spacing ......................................................................................................................................... 30 4.4.2 Channel raster ............................................................................................................................................ 30 4.4.3 Channel number ......................................................................................................................................... 30 4.4.4 UARFCN ................................................................................................................................................... 31 4A Reference Conditions .............................................................................................................................31 4A.1 Generic setup procedures................................................................................................................................. 32 4A.2 System information.......................................................................................................................................... 32 4A.3 Message contents ............................................................................................................................................. 32 4A.4 Measurement configurations............................................................................................................................ 32 5 Transmitter Characteristics ....................................................................................................................33 5.1 General............................................................................................................................................................. 33 5.2 Maximum Output Power ................................................................................................................................. 33 5.2.1 Definition and applicability........................................................................................................................ 33 5.2.2 Minimum Requirements............................................................................................................................. 34 5.2.3 Test purpose ............................................................................................................................................... 34 5.2.4 Method of test ............................................................................................................................................ 34 5.2.4.1 Initial conditions................................................................................................................................... 34 5.2.4.2 Procedure.............................................................................................................................................. 34 5.2.5 Test requirements ....................................................................................................................................... 34 5.2A Maximum Output Power with HS-DPCCH (Release 5 only).......................................................................... 35 5.2A.1 Definition and applicability........................................................................................................................ 35 5.2A.2 Minimum Requirements............................................................................................................................. 35 5.2A.3 Test purpose ............................................................................................................................................... 35 5.2A.4 Method of test ............................................................................................................................................ 36 5.2A.4.1 Initial conditions................................................................................................................................... 36 5.2A.4.2 Procedure.............................................................................................................................................. 36 5.2A.5 Test requirements ....................................................................................................................................... 36 5.2AA Maximum Output Power with HS-DPCCH (Release 6 and later) ................................................................... 37 5.2AA.1 Definition and applicability........................................................................................................................ 37 5.2AA.2 Minimum Requirements............................................................................................................................. 37 5.2AA.3 Test purpose ............................................................................................................................................... 38 5.2AA.4 Method of test ............................................................................................................................................ 38 5.2AA.4.1 Initial conditions................................................................................................................................... 38 5.2AA.4.2 Procedure.............................................................................................................................................. 38 5.2AA.5 Test requirements ....................................................................................................................................... 38 5.2B Maximum Output Power with HS-DPCCH and E-DCH................................................................................. 39 5.2B.1 Definition and applicability........................................................................................................................ 39 5.2B.2 Minimum Requirements............................................................................................................................. 39 5.2B.3 Test purpose ............................................................................................................................................... 39 5.2B.4 Method of test ............................................................................................................................................ 40

Release 7 4 3GPP TS 34.121-1 V7.1.0 (2006-06)

5.2B.4.1 Initial conditions................................................................................................................................... 40 5.2B.4.2 Procedure.............................................................................................................................................. 40 5.2B.5 Test requirements ....................................................................................................................................... 40 5.3 Frequency Error ............................................................................................................................................... 41 5.3.1 Definition and applicability........................................................................................................................ 41 5.3.2 Minimum Requirements............................................................................................................................. 41 5.3.3 Test purpose ............................................................................................................................................... 41 5.3.4 Method of test ............................................................................................................................................ 41 5.3.5 Test Requirements...................................................................................................................................... 41 5.4 Output Power Dynamics in the Uplink ............................................................................................................ 42 5.4.1 Open Loop Power Control in the Uplink ................................................................................................... 42 5.4.1.1 Definition and applicability .................................................................................................................. 42 5.4.1.2 Minimum requirements ........................................................................................................................ 42 5.4.1.3 Test purpose ......................................................................................................................................... 42 5.4.1.4 Method of test....................................................................................................................................... 42 5.4.1.5 Test requirements ................................................................................................................................. 43 5.4.2 Inner Loop Power Control in the Uplink.................................................................................................... 44 5.4.2.1 Definition and applicability .................................................................................................................. 44 5.4.2.2 Minimum requirements ........................................................................................................................ 44 5.4.2.3 Test purpose ......................................................................................................................................... 45 5.4.2.4 Method of test....................................................................................................................................... 45 5.4.2.5 Test requirements ................................................................................................................................. 49 5.4.3 Minimum Output Power............................................................................................................................. 51 5.4.3.1 Definition and applicability .................................................................................................................. 51 5.4.3.2 Minimum Requirements ....................................................................................................................... 51 5.4.3.3 Test purpose ......................................................................................................................................... 51 5.4.3.4 Method of test....................................................................................................................................... 51 5.4.3.5 Test requirements ................................................................................................................................. 52 5.4.4 Out-of-synchronisation handling of output power ..................................................................................... 52 5.4.4.1 Definition and applicability .................................................................................................................. 52 5.4.4.2 Minimum Requirements ....................................................................................................................... 52 5.4.4.3 Test purpose ......................................................................................................................................... 53 5.4.4.4 Method of test....................................................................................................................................... 54 5.4.4.5 Test requirements ................................................................................................................................. 54 5.5 Transmit ON/OFF Power................................................................................................................................. 55 5.5.1 Transmit OFF Power.................................................................................................................................. 55 5.5.1.1 Definition and applicability .................................................................................................................. 55 5.5.1.2 Minimum Requirements ....................................................................................................................... 55 5.5.1.3 Test purpose ......................................................................................................................................... 55 5.5.1.4 Method of test....................................................................................................................................... 55 5.5.1.5 Test requirements ................................................................................................................................. 55 5.5.2 Transmit ON/OFF Time mask ................................................................................................................... 55 5.5.2.1 Definition and applicability .................................................................................................................. 55 5.5.2.2 Minimum requirements ........................................................................................................................ 55 5.5.2.3 Test purpose ......................................................................................................................................... 57 5.5.2.4 Method of test....................................................................................................................................... 57 5.5.2.5 Test requirements ................................................................................................................................. 59 5.6 Change of TFC ................................................................................................................................................ 59 5.6.1 Definition and applicability........................................................................................................................ 59 5.6.2 Minimum requirements .............................................................................................................................. 59 5.6.3 Test purpose ............................................................................................................................................... 60 5.6.4 Method of test ............................................................................................................................................ 60 5.6.5 Test requirements ....................................................................................................................................... 61 5.7 Power setting in uplink compressed mode....................................................................................................... 61 5.7.1 Definition and applicability........................................................................................................................ 61 5.7.2 Minimum requirements .............................................................................................................................. 61 5.7.3 Test purpose ............................................................................................................................................... 63 5.7.4 Method of test ............................................................................................................................................ 63 5.7.5 Test requirements ....................................................................................................................................... 70 5.7A HS-DPCCH...................................................................................................................................................... 72 5.7A.1 Definition and applicability........................................................................................................................ 72 5.7A.2 Minimum requirement ............................................................................................................................. 72

Release 7 5 3GPP TS 34.121-1 V7.1.0 (2006-06)

5.7A.3 Test purpose ............................................................................................................................................... 73 5.7A.4 Method of test ............................................................................................................................................ 73 5.7A.5 Test requirements ....................................................................................................................................... 74 5.8 Occupied Bandwidth (OBW)........................................................................................................................... 76 5.8.1 Definition and applicability........................................................................................................................ 76 5.8.2 Minimum Requirements............................................................................................................................. 76 5.8.3 Test purpose ............................................................................................................................................... 76 5.8.4 Method of test ............................................................................................................................................ 76 5.8.5 Test Requirements...................................................................................................................................... 76 5.9 Spectrum emission mask ................................................................................................................................. 77 5.9.1 Definition and applicability........................................................................................................................ 77 5.9.2 Minimum Requirements............................................................................................................................. 77 5.9.3 Test purpose ............................................................................................................................................... 77 5.9.4 Method of test ............................................................................................................................................ 77 5.9.4.1 Initial conditions................................................................................................................................... 77 5.9.4.2 Procedure.............................................................................................................................................. 78 5.9.5 Test requirements ....................................................................................................................................... 78 5.9A Spectrum Emission Mask with HS-DPCCH.................................................................................................... 79 5.9A.1 Definition and applicability........................................................................................................................ 79 5.9A.2 Minimum Requirements............................................................................................................................. 79 5.9A.3 Test purpose ............................................................................................................................................... 80 5.9A.4 Method of test ............................................................................................................................................ 80 5.9A.4.1 Initial conditions................................................................................................................................... 80 5.9A.4.2 Procedure.............................................................................................................................................. 81 5.9A.5 Test requirements ....................................................................................................................................... 81 5.9B Spectrum Emission Mask with E-DCH ........................................................................................................... 82 5.9B.1 Definition and applicability........................................................................................................................ 82 5.9B.2 Minimum Requirements............................................................................................................................. 82 5.9B.3 Test purpose ............................................................................................................................................... 83 5.9B.4 Method of test ............................................................................................................................................ 83 5.9B.4.1 Initial conditions................................................................................................................................... 83 5.9B.4.2 Procedure.............................................................................................................................................. 84 5.9B.5 Test requirements ....................................................................................................................................... 84 5.10 Adjacent Channel Leakage Power Ratio (ACLR) ........................................................................................... 85 5.10.1 Definition and applicability........................................................................................................................ 85 5.10.2 Minimum Requirements............................................................................................................................. 85 5.10.3 Test purpose ............................................................................................................................................... 86 5.10.4 Method of test ............................................................................................................................................ 86 5.10.5 Test requirements ....................................................................................................................................... 86 5.10A Adjacent Channel Leakage Power Ratio (ACLR) with HS-DPCCH............................................................... 87 5.10A.1 Definition and applicability........................................................................................................................ 87 5.10A.2 Minimum Requirements............................................................................................................................. 87 5.10A.3 Test purpose ............................................................................................................................................... 87 5.10A.4 Method of test ............................................................................................................................................ 87 5.10A.5 Test requirements ....................................................................................................................................... 88 5.10B Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH ...................................................................... 88 5.10B.1 Definition and applicability........................................................................................................................ 88 5.10B.2 Minimum Requirements............................................................................................................................. 89 5.10B.3 Test purpose ............................................................................................................................................... 89 5.10B.4 Method of test ............................................................................................................................................ 89 5.10B.5 Test requirements ....................................................................................................................................... 90 5.11 Spurious Emissions.......................................................................................................................................... 90 5.11.1 Definition and applicability........................................................................................................................ 90 5.11.2 Minimum Requirements............................................................................................................................. 90 5.11.3 Test purpose ............................................................................................................................................... 92 5.11.4 Method of test ............................................................................................................................................ 92 5.11.5 Test requirements ....................................................................................................................................... 92 5.12 Transmit Intermodulation ................................................................................................................................ 94 5.12.1 Definition and applicability........................................................................................................................ 94 5.12.2 Minimum Requirements............................................................................................................................. 94 5.12.3 Test purpose ............................................................................................................................................... 94 5.12.4 Method of test ............................................................................................................................................ 95

Release 7 6 3GPP TS 34.121-1 V7.1.0 (2006-06)

5.12.5 Test requirements ....................................................................................................................................... 95 5.13 Transmit Modulation ....................................................................................................................................... 95 5.13.1 Error Vector Magnitude (EVM)................................................................................................................. 95 5.13.1.1 Definition and applicability .................................................................................................................. 95 5.13.1.2 Minimum Requirements ....................................................................................................................... 96 5.13.1.3 Test purpose ......................................................................................................................................... 96 5.13.1.4 Method of test....................................................................................................................................... 96 5.13.1.5 Test requirements ................................................................................................................................. 96 5.13.1A Error Vector Magnitude (EVM) with HS-DPCCH .................................................................................... 97 5.13.1A.1 Definition and applicability .................................................................................................................. 97 5.13.1A.2 Minimum Requirements ....................................................................................................................... 97 5.13.1A.3 Test purpose ......................................................................................................................................... 97 5.13.1A.4 Method of test....................................................................................................................................... 97 5.13.1A.5 Test requirements ................................................................................................................................. 99 5.13.1AA Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH.............................................. 99 5.13.1AA.1 Definition and applicability .................................................................................................................. 99 5.13.1AA.2 Minimum Requirements ..................................................................................................................... 100 5.13.1AA.3 Test purpose ....................................................................................................................................... 100 5.13.1AA.4 Method of test..................................................................................................................................... 100 5.13.1AA.5 Test requirements ............................................................................................................................... 102 5.13.2 Peak code domain error............................................................................................................................ 102 5.13.2.1 Definition and applicability ................................................................................................................ 102 5.13.2.2 Minimum Requirements ..................................................................................................................... 103 5.13.2.3 Test purpose ....................................................................................................................................... 103 5.13.2.4 Method of test..................................................................................................................................... 103 5.13.2.5 Test requirements ............................................................................................................................... 103 5.13.3 UE phase discontinuity ............................................................................................................................ 104 5.13.3.1 Definition and applicability ................................................................................................................ 104 5.13.3.2 Minimum requirements ...................................................................................................................... 104 5.13.3.3 Test purpose ....................................................................................................................................... 105 5.13.3.4 Method of test..................................................................................................................................... 105 5.13.3.5 Test requirements ............................................................................................................................... 106 5.13.4 PRACH preamble quality......................................................................................................................... 107 5.13.4.1 Definition and applicability ................................................................................................................ 107 5.13.4.2 Minimum requirements ...................................................................................................................... 107 5.13.4.3 Test purpose ....................................................................................................................................... 107 5.13.4.4 Method of test..................................................................................................................................... 107 5.13.4.5 Test requirements ............................................................................................................................... 108 6 Receiver Characteristics.......................................................................................................................109 6.1 General........................................................................................................................................................... 109 6.2 Reference Sensitivity Level ........................................................................................................................... 109 6.2.1 Definition and applicability...................................................................................................................... 109 6.2.2 Minimum Requirements........................................................................................................................... 110 6.2.3 Test purpose ............................................................................................................................................. 110 6.2.4 Method of test .......................................................................................................................................... 110 6.2.5 Test requirements ..................................................................................................................................... 111 6.3 Maximum Input Level ................................................................................................................................... 111 6.3.1 Definition and applicability...................................................................................................................... 111 6.3.2 Minimum requirements ............................................................................................................................ 111 6.3.3 Test purpose ............................................................................................................................................. 111 6.3.4 Method of test .......................................................................................................................................... 111 6.3.5 Test requirements ..................................................................................................................................... 112 6.3A Maximum Input Level for HS-PDSCH Reception (16QAM) ....................................................................... 112 6.3A.1 Definition and applicability...................................................................................................................... 112 6.3A.2 Minimum requirements ............................................................................................................................ 113 6.3A.3 Test purpose ............................................................................................................................................. 113 6.3A.4 Method of test .......................................................................................................................................... 113 6.3A.5 Test requirements ..................................................................................................................................... 114 6.4 Adjacent Channel Selectivity (ACS) (Rel-99 and Rel-4) .............................................................................. 114 6.4.1 Definition and applicability...................................................................................................................... 114 6.4.2 Minimum Requirements........................................................................................................................... 114

Release 7 7 3GPP TS 34.121-1 V7.1.0 (2006-06)

6.4.3 Test purpose ............................................................................................................................................. 115 6.4.4 Method of test .......................................................................................................................................... 115 6.4.5 Test requirements ..................................................................................................................................... 115 6.4A Adjacent Channel Selectivity (ACS) (Rel-5 and later releases)..................................................................... 116 6.4A.1 Definition and applicability...................................................................................................................... 116 6.4A.2 Minimum Requirements........................................................................................................................... 116 6.4A.3 Test purpose ............................................................................................................................................. 116 6.4A.4 Method of test .......................................................................................................................................... 116 6.4A.5 Test requirements ..................................................................................................................................... 117 6.5 Blocking Characteristics ................................................................................................................................ 117 6.5.1 Definition and applicability...................................................................................................................... 117 6.5.2 Minimum Requirements........................................................................................................................... 117 6.5.2.1 Minimum Requirements (In-band blocking) ...................................................................................... 117 6.5.2.2 Minimum requirements (Out of-band blocking) ................................................................................ 118 6.5.2.3 Minimum requirements (Narrow band blocking) ............................................................................... 119 6.5.3 Test purpose ............................................................................................................................................. 120 6.5.4 Method of test .......................................................................................................................................... 120 6.5.5 Test requirements ..................................................................................................................................... 121 6.6 Spurious Response......................................................................................................................................... 123 6.6.1 Definition and applicability...................................................................................................................... 123 6.6.2 Minimum Requirements........................................................................................................................... 123 6.6.3 Test purpose ............................................................................................................................................. 123 6.6.4 Method of test .......................................................................................................................................... 123 6.6.5 Test requirements ..................................................................................................................................... 124 6.7 Intermodulation Characteristics ..................................................................................................................... 124 6.7.1 Definition and applicability...................................................................................................................... 124 6.7.2 Minimum Requirements........................................................................................................................... 124 6.7.3 Test purpose ............................................................................................................................................. 125 6.7.4 Method of test .......................................................................................................................................... 125 6.7.5 Test requirements ..................................................................................................................................... 126 6.8 Spurious Emissions........................................................................................................................................ 126 6.8.1 Definition and applicability...................................................................................................................... 126 6.8.2 Minimum Requirements........................................................................................................................... 126 6.8.3 Test purpose ............................................................................................................................................. 128 6.8.4 Method of test .......................................................................................................................................... 128 6.8.5 Test requirements ..................................................................................................................................... 129 7 Performance requirements....................................................................................................................132 7.1 General........................................................................................................................................................... 132 7.1.1 Measurement Configurations ................................................................................................................... 132 7.1.2 Definition of Additive White Gaussian Noise (AWGN) Interferer.......................................................... 132 7.2 Demodulation in Static Propagation conditions............................................................................................. 133 7.2.1 Demodulation of Dedicated Channel (DCH) ........................................................................................... 133 7.2.1.1 Definition and applicability ................................................................................................................ 133 7.2.1.2 Minimum requirements ...................................................................................................................... 133 7.2.1.3 Test purpose ....................................................................................................................................... 133 7.2.1.4 Method of test..................................................................................................................................... 133 7.2.1.5 Test requirements ............................................................................................................................... 134 7.3 Demodulation of DCH in Multi-path Fading Propagation conditions ........................................................... 134 7.3.1 Single Link Performance.......................................................................................................................... 134 7.3.1.1 Definition and applicability ................................................................................................................ 134 7.3.1.2 Minimum requirements ...................................................................................................................... 135 7.3.1.3 Test purpose ....................................................................................................................................... 137 7.3.1.4 Method of test..................................................................................................................................... 137 7.3.1.5 Test requirements ............................................................................................................................... 137 7.4 Demodulation of DCH in Moving Propagation conditions ........................................................................... 140 7.4.1 Single Link Performance.......................................................................................................................... 140 7.4.1.1 Definition and applicability ................................................................................................................ 140 7.4.1.2 Minimum requirements ...................................................................................................................... 140 7.4.1.3 Test purpose ....................................................................................................................................... 141 7.4.1.4 Method of test..................................................................................................................................... 141 7.4.1.5 Test requirements ............................................................................................................................... 141

Release 7 8 3GPP TS 34.121-1 V7.1.0 (2006-06)

7.5 Demodulation of DCH in Birth-Death Propagation conditions ..................................................................... 141 7.5.1 Single Link Performance.......................................................................................................................... 141 7.5.1.1 Definition and applicability ................................................................................................................ 141 7.5.1.2 Minimum requirements ...................................................................................................................... 142 7.5.1.3 Test purpose ....................................................................................................................................... 142 7.5.1.4 Method of test..................................................................................................................................... 142 7.5.1.5 Test requirements ............................................................................................................................... 142 7.6 Demodulation of DCH in downlink Transmit diversity modes ..................................................................... 143 7.6.1 Demodulation of DCH in open-loop transmit diversity mode ................................................................. 143 7.6.1.1 Definition and applicability ................................................................................................................ 143 7.6.1.2 Minimum requirements ...................................................................................................................... 143 7.6.1.3 Test purpose ....................................................................................................................................... 144 7.6.1.4 Method of test..................................................................................................................................... 144 7.6.1.5 Test Requirements .............................................................................................................................. 145 7.6.2 Demodulation of DCH in closed loop transmit diversity mode ............................................................... 145 7.6.2.1 Definition and applicability ................................................................................................................ 145 7.6.2.2 Minimum requirements ...................................................................................................................... 145 7.6.2.3 Test purpose ....................................................................................................................................... 146 7.6.2.4 Method of test..................................................................................................................................... 146 7.6.2.5 Test Requirements .............................................................................................................................. 148 7.6.3 Demodulation of DCH in Site Selection Diversity Transmission Power Control mode.......................... 149 7.6.3.1 Definition and applicability ................................................................................................................ 149 7.6.3.2 Minimum requirements ...................................................................................................................... 149 7.6.3.3 Test purpose ....................................................................................................................................... 149 7.6.3.4 Method of test..................................................................................................................................... 150 7.6.3.5 Test Requirements .............................................................................................................................. 153 7.7 Demodulation in Handover conditions .......................................................................................................... 154 7.7.1 Demodulation of DCH in Inter-Cell Soft Handover ................................................................................ 154 7.7.1.1 Definition and applicability ................................................................................................................ 154 7.7.1.2 Minimum requirements ...................................................................................................................... 154 7.7.1.3 Test purpose ....................................................................................................................................... 155 7.7.1.4 Method of test..................................................................................................................................... 155 7.7.1.5 Test requirements ............................................................................................................................... 155 7.7.2 Combining of TPC commands from radio links of different radio link sets ............................................ 156 7.7.2.1 Definition and applicability ................................................................................................................ 156 7.7.2.2 Minimum requirements ...................................................................................................................... 156 7.7.2.3 Test purpose ....................................................................................................................................... 157 7.7.2.4 Method of test..................................................................................................................................... 157 7.7.2.5 Test requirements ............................................................................................................................... 158 7.7.3 Combining of reliable TPC commands from radio links of different radio link sets ............................... 159 7.7.3.1 Definition and applicability ................................................................................................................ 159 7.7.3.2 Minimum requirements ...................................................................................................................... 159 7.7.3.3 Test purpose ....................................................................................................................................... 160 7.7.3.4 Method of test..................................................................................................................................... 161 7.7.3.4.1 Test 1 Initial conditions ................................................................................................................ 161 7.7.3.4.2 Test 1 Procedures.......................................................................................................................... 161 7.7.3.4.3 Test 2 Initial conditions ................................................................................................................ 161 7.7.3.4.4 Test 2 Procedures.......................................................................................................................... 161 7.7.3.5 Test requirements ............................................................................................................................... 162 7.8 Power control in downlink............................................................................................................................. 162 7.8.1 Power control in the downlink, constant BLER target............................................................................. 163 7.8.1.1 Definition and applicability ................................................................................................................ 163 7.8.1.2 Minimum requirements ...................................................................................................................... 163 7.8.1.3 Test purpose ....................................................................................................................................... 164 7.8.1.4 Method of test..................................................................................................................................... 164 7.8.1.5 Test Requirements .............................................................................................................................. 164 7.8.2 Power control in the downlink, initial convergence ................................................................................. 165 7.8.2.1 Definition and applicability ................................................................................................................ 165 7.8.2.2 Minimum requirements ...................................................................................................................... 165 7.8.2.3 Test purpose ....................................................................................................................................... 166 7.8.2.4 Method of test..................................................................................................................................... 166 7.8.2.5 Test Requirements .............................................................................................................................. 166

Release 7 9 3GPP TS 34.121-1 V7.1.0 (2006-06)

7.8.3 Power control in the downlink, wind up effects....................................................................................... 168 7.8.3.1 Definition and applicability .............................................................................................................. 168 7.8.3.2 Minimum requirements ...................................................................................................................... 168 7.8.3.3 Test purpose ....................................................................................................................................... 168 7.8.3.4 Method of test..................................................................................................................................... 169 7.8.3.5 Test Requirements .............................................................................................................................. 169 7.8.4 Power control in the downlink, different transport formats ..................................................................... 170 7.8.4.1 Definition and applicability .............................................................................................................. 170 7.8.4.2 Minimum requirements ...................................................................................................................... 170 7.8.4.3 Test purpose ....................................................................................................................................... 171 7.8.4.4 Method of test..................................................................................................................................... 171 7.8.4.5 Test Requirements .............................................................................................................................. 172 7.9 Downlink compressed mode.......................................................................................................................... 173 7.9.1 Single link performance ........................................................................................................................... 173 7.9.1.1 Definition and applicability ................................................................................................................ 173 7.9.1.2 Minimum requirements ...................................................................................................................... 173 7.9.1.3 Test purpose ....................................................................................................................................... 174 7.9.1.4 Method of test..................................................................................................................................... 174 7.9.1.5 Test requirements ............................................................................................................................... 175 7.10 Blind transport format detection .................................................................................................................... 176 7.10.1 Definition and applicability...................................................................................................................... 176 7.10.2 Minimum requirements ............................................................................................................................ 176 7.10.3 Test purpose ............................................................................................................................................. 177 7.10.4 Method of test .......................................................................................................................................... 177 7.10.5 Test requirements ..................................................................................................................................... 177 7.11 Demodulation of Paging Channel (PCH)....................................................................................................... 178 7.11.1 Definition and applicability...................................................................................................................... 178 7.11.2 Minimum requirements ............................................................................................................................ 178 7.11.3 Test purpose ............................................................................................................................................. 179 7.11.4 Method of test .......................................................................................................................................... 179 7.11.5 Test requirements ..................................................................................................................................... 181 7.12 Detection of Acquisition Indicator (AI)......................................................................................................... 182 7.12.1 Definition and applicability...................................................................................................................... 182 7.12.2 Minimum requirements ............................................................................................................................ 182 7.12.3 Test purpose ............................................................................................................................................. 182 7.12.4 Method of test .......................................................................................................................................... 182 7.12.5 Test requirements ..................................................................................................................................... 184 8 Requirements for support of RRM.......................................................................................................185 8.1 General........................................................................................................................................................... 185 8.1.1 Definition of Additive White Gaussian Noise (AWGN) Interferer.......................................................... 185 8.2 Idle Mode Tasks ............................................................................................................................................ 185 8.2.1 Cell Selection ........................................................................................................................................... 185 8.2.2 Cell Re-Selection ..................................................................................................................................... 185 8.2.2.1 Scenario 1: Single carrier case............................................................................................................ 185 8.2.2.1.1 Definition and applicability .......................................................................................................... 185 8.2.2.1.2 Minimum requirement .................................................................................................................. 185 8.2.2.1.3 Test purpose.................................................................................................................................. 185 8.2.2.1.4 Method of test ............................................................................................................................... 185 8.2.2.1.5 Test requirements.......................................................................................................................... 188 8.2.2.2 Scenario 2: Multi carrier case ............................................................................................................. 189 8.2.2.2.1 Definition and applicability .......................................................................................................... 189 8.2.2.2.2 Minimum requirement .................................................................................................................. 189 8.2.2.2.3 Test purpose.................................................................................................................................. 189 8.2.2.2.4 Method of test ............................................................................................................................... 189 8.2.2.2.5 Test requirements.......................................................................................................................... 192 8.2.3 UTRAN to GSM Cell Re-Selection ......................................................................................................... 194 8.2.3.1 Scenario 1: Both UTRA and GSM level changed .............................................................................. 194 8.2.3.1.1 Definition and applicability .......................................................................................................... 194 8.2.3.1.2 Minimum requirement .................................................................................................................. 194 8.2.3.1.3 Test purpose.................................................................................................................................. 194 8.2.3.1.4 Method of test ............................................................................................................................... 194

Release 7 10 3GPP TS 34.121-1 V7.1.0 (2006-06)

8.2.3.1.5 Test requirements.......................................................................................................................... 196 8.2.3.2 Scenario 2: Only UTRA level changed .............................................................................................. 196 8.2.3.2.1 Definition and applicability .......................................................................................................... 196 8.2.3.2.2 Minimum requirement .................................................................................................................. 197 8.2.3.2.3 Test purpose.................................................................................................................................. 197 8.2.3.2.4 Method of test ............................................................................................................................... 197 8.2.3.2.5 Test requirements.......................................................................................................................... 199 8.2.3.3 Scenario 3: HCS with only UTRA level changed .............................................................................. 199 8.2.3.3.1 Definition and applicability .......................................................................................................... 199 8.2.3.3.2 Minimum requirement .................................................................................................................. 199 8.2.3.3.3 Test purpose.................................................................................................................................. 200 8.2.3.3.4 Method of test ............................................................................................................................... 200 8.2.3.3.5 Test requirements.......................................................................................................................... 203 8.2.4 FDD/TDD Cell Re-selection.................................................................................................................... 203 8.2.4.1 Definition and applicability ................................................................................................................ 203 8.2.4.1.1 3.84 Mcps TDD Option ................................................................................................................ 204 8.2.4.1.2 1.28 Mcps TDD Option ................................................................................................................ 204 8.2.4.2 Minimum requirement........................................................................................................................ 204 8.2.4.3 Test purpose ....................................................................................................................................... 204 8.2.4.4 Method of test..................................................................................................................................... 204 8.2.4.4.1.1 3.84 Mcps TDD Option........................................................................................................... 204 8.2.4.4.1.2 1.28Mcps TDD Option............................................................................................................ 205 8.2.4.5 Test requirements ............................................................................................................................... 207 8.3 UTRAN Connected Mode Mobility .............................................................................................................. 207 8.3.1 FDD/FDD Soft Handover ........................................................................................................................ 207 8.3.1.1 Definition and applicability ................................................................................................................ 207 8.3.1.2 Minimum requirement........................................................................................................................ 207 8.3.1.3 Test purpose ....................................................................................................................................... 208 8.3.1.4 Method of test..................................................................................................................................... 208 8.3.1.5 Test requirements ............................................................................................................................... 215 8.3.2 FDD/FDD Hard Handover ....................................................................................................................... 216 8.3.2.1 FDD/FDD Hard Handover to intra-frequency cell ............................................................................. 216 8.3.2.1.1 Definition and applicability .......................................................................................................... 216 8.3.2.1.2 Minimum requirement .................................................................................................................. 216 8.3.2.1.3 Test purpose.................................................................................................................................. 217 8.3.2.1.4 Method of test ............................................................................................................................... 217 8.3.2.1.5 Test requirements.......................................................................................................................... 224 8.3.2.2 FDD/FDD Hard Handover to inter-frequency cell ............................................................................. 225 8.3.2.2.1 Definition and applicability .......................................................................................................... 225 8.3.2.2.2 Minimum requirement .................................................................................................................. 225 8.3.2.2.3 Test purpose.................................................................................................................................. 225 8.3.2.2.4 Method of test ............................................................................................................................... 226 8.3.2.2.5 Test requirements.......................................................................................................................... 232 8.3.3 FDD/TDD Handover................................................................................................................................ 233 8.3.3.1 Definition and applicability ................................................................................................................ 233 8.3.3.2 Minimum requirement........................................................................................................................ 233 8.3.3.3 Test purpose ....................................................................................................................................... 233 8.3.3.4 Method of test..................................................................................................................................... 233 8.3.3.5 Test requirements ............................................................................................................................... 238 8.3.4 Inter-system Handover from UTRAN FDD to GSM ............................................................................... 239 8.3.4.1 Definition and applicability .......................................................................................................... 239 8.3.4.2 Minimum requirement .................................................................................................................. 239 8.3.4.3 Test purpose.................................................................................................................................. 239 8.3.4.4 Method of test ............................................................................................................................... 239 8.3.4.5 Test requirements.......................................................................................................................... 244 8.3.5 Cell Re-selection in CELL_FACH........................................................................................................... 245 8.3.5.1 One frequency present in neighbour list ............................................................................................. 245 8.3.5.1.1 Definition and applicability .......................................................................................................... 245 8.3.5.1.2 Minimum requirements................................................................................................................. 245 8.3.5.1.3 Test purpose.................................................................................................................................. 245 8.3.5.1.4 Method of test ............................................................................................................................... 245 8.3.5.1.5 Test requirements.......................................................................................................................... 248

Release 7 11 3GPP TS 34.121-1 V7.1.0 (2006-06)

8.3.5.2 Two frequencies present in the neighbour list .................................................................................... 248 8.3.5.2.1 Definition and applicability .......................................................................................................... 248 8.3.5.2.2 Minimum requirements................................................................................................................. 248 8.3.5.2.3 Test purpose.................................................................................................................................. 249 8.3.5.2.4 Method of test ............................................................................................................................... 249 8.3.5.2.5 Test requirements.......................................................................................................................... 252 8.3.5.3 Cell Reselection to GSM .................................................................................................................... 252 8.3.5.3.1 Definition and applicability .......................................................................................................... 252 8.3.5.3.2 Minimum requirements................................................................................................................. 252 8.3.5.3.3 Test purpose.................................................................................................................................. 253 8.3.5.3.4 Method of test ............................................................................................................................... 253 8.3.5.3.5 Test requirements.......................................................................................................................... 255 8.3.6 Cell Re-selection in CELL_PCH ............................................................................................................. 256 8.3.6.1 One frequency present in the neighbour list ....................................................................................... 256 8.3.6.1.1 Definition and applicability .......................................................................................................... 256 8.3.6.1.2 Minimum requirements................................................................................................................. 256 8.3.6.1.3 Test purpose.................................................................................................................................. 256 8.3.6.1.4 Method of test ............................................................................................................................... 256 8.3.6.1.5 Test requirements.......................................................................................................................... 260 8.3.6.2 Two frequencies present in the neighbour list .................................................................................... 260 8.3.6.2.1 Definition and applicability .......................................................................................................... 260 8.3.6.2.2 Minimum requirement .................................................................................................................. 261 8.3.6.2.3 Test purpose.................................................................................................................................. 261 8.3.6.2.4 Method of test ............................................................................................................................... 261 8.3.6.2.5 Test requirements.......................................................................................................................... 265 8.3.7 Cell Re-selection in URA_PCH............................................................................................................... 266 8.3.7.1 One frequency present in the neighbour list ....................................................................................... 266 8.3.7.1.1 Definition and applicability .......................................................................................................... 266 8.3.7.1.2 Minimum requirement .................................................................................................................. 266 8.3.7.1.3 Test purpose.................................................................................................................................. 266 8.3.7.1.4 Method of test ............................................................................................................................... 266 8.3.7.1.5 Test requirements.......................................................................................................................... 270 8.3.7.2 Two frequencies present in the neighbour list .................................................................................... 270 8.3.7.2.1 Definition and applicability .......................................................................................................... 270 8.3.7.2.2 Minimum requirement .................................................................................................................. 270 8.3.7.2.3 Test purpose.................................................................................................................................. 271 8.3.7.2.4 Method of test ............................................................................................................................... 271 8.3.7.2.5 Test requirements.......................................................................................................................... 274 8.3.8 Serving HS-DSCH cell change ................................................................................................................ 274 8.3.8.1 Definition and applicability ................................................................................................................ 274 8.3.8.2 Minimum requirement........................................................................................................................ 275 8.3.8.3 Test purpose ....................................................................................................................................... 275 8.3.8.4 Method of test..................................................................................................................................... 275 8.3.8.4.1 Initial conditions ........................................................................................................................... 277 8.3.8.4.2 Procedure ...................................................................................................................................... 277 8.3.8.5 Test requirements ............................................................................................................................... 287 8.4 RRC Connection Control............................................................................................................................... 288 8.4.1 RRC Re-establishment delay ................................................................................................................... 288 8.4.1.1 Test 1 .................................................................................................................................................. 288 8.4.1.1.1 Definition and applicability .......................................................................................................... 288 8.4.1.1.2 Minimum requirement .................................................................................................................. 288 8.4.1.1.3 Test purpose.................................................................................................................................. 289 8.4.1.1.4 Method of test ............................................................................................................................... 289 8.4.1.1.5 Test requirements.......................................................................................................................... 291 8.4.1.2 Test 2 .................................................................................................................................................. 291 8.4.1.2.1 Definition and applicability .......................................................................................................... 291 8.4.1.2.2 Minimum requirement .................................................................................................................. 291 8.4.1.2.3 Test purpose.................................................................................................................................. 292 8.4.1.2.4 Method of test ............................................................................................................................... 292 8.4.1.2.5 Test requirements.......................................................................................................................... 293 8.4.2 Random Access........................................................................................................................................ 294 8.4.2.1 Correct behaviour when receiving an ACK (Release 5 and earlier)................................................... 294

Release 7 12 3GPP TS 34.121-1 V7.1.0 (2006-06)

8.4.2.1.1 Definition and applicability .......................................................................................................... 294 8.4.2.1.2 Minimum Requirements ............................................................................................................... 294 8.4.2.1.3 Test purpose.................................................................................................................................. 294 8.4.2.1.4 Method of test ............................................................................................................................... 294 8.4.2.1.5 Test requirements.......................................................................................................................... 296 8.4.2.1A Correct behaviour when receiving an ACK (Release 6 and later) ...................................................... 297 8.4.2.1A.1 Definition and applicability .......................................................................................................... 297 8.4.2.1A.2 Minimum Requirements ............................................................................................................... 297 8.4.2.1A.3 Test purpose.................................................................................................................................. 297 8.4.2.1A.4 Method of test ............................................................................................................................... 297 8.4.2.1A.5 Test requirements.......................................................................................................................... 299 8.4.2.2 Correct behaviour when receiving an NACK..................................................................................... 300 8.4.2.2.1 Definition and applicability .......................................................................................................... 300 8.4.2.2.2 Minimum Requirements ............................................................................................................... 300 8.4.2.2.3 Test purpose.................................................................................................................................. 300 8.4.2.2.4 Method o

3GPP TS 34.121-1 - 株式会社QT · Testing, UMTS 3GPP Postal address 3GPP support office address...

Documents

Transcript of 3GPP TS 34.121-1 - 株式会社QT · Testing, UMTS 3GPP Postal address 3GPP support office address...