3DR Solo DJI Phantom 3 - MicaSense Knowledge Base · Parrot SequoiaTM Integration Kit Instructions:...
Transcript of 3DR Solo DJI Phantom 3 - MicaSense Knowledge Base · Parrot SequoiaTM Integration Kit Instructions:...
3DR Solo
DJI Phantom 3
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
1
3DR Solo Instructions Parts Included
2x – Parrot Sequoia mounting brackets
2x – Rubber pads
1x – power and data board
2x – Zip tie anchors
2x – Zip ties
1x – VHB tape square
Required Tools
#1 Phillips head screwdriver Scissors
Steps
1. Remove the 3 screws on the gimbal bay cover.
Figure 1 Arrows show screws to remove gimbal bay cover
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
2
2. Pull off the gimbal bay cover.
Figure 2 Gimbal bay cover pulled off
3. Clean the area outlined to remove all foreign debris and oils.
Figure 3 Clean area indicated with red box with alcohol
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
3
4. Remove the adhesive cover from the power and data board.
5. Thread the USB connector through the hole in the cover shown and adhere the board as shown to
the cover.
6. Locate the Solo gimbal cable and plug in the power adaptor as shown.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
4
7. Replace the gimbal bay cover with the three screws.
8. Remove the GoPro mount pin.
Figure 4 GoPro mount pin removed
9. Remove adhesive protector from 1 rubber pad.
Figure 5 Adhesive backing pad being removed
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
5
10. Place pad on bracket as shown, repeat for second bracket.
Figure 6 Rubber pad added to bracket - highlighted in red for guide
11. Place brackets over Parrot Sequoia camera.
Figure 7 Brackets placed over Parrot Sequoia camera
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
6
12. Slip the tabs of the brackets into the GoPro mount on the Solo.
Figure 8 Parrot Sequoia in bracket with bracket tabs inserted in the GoPro mount
13. Replace the screw on the GoPro mount and position camera as necessary.
Figure 9 Camera secured
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
7
14. Connect the micro USB power connector to the camera.
Figure 10 Power cord inserted into camera
15. Use the included VHB tape to secure the Parrot Sequoia Sunshine Sensor to the battery of the Solo
as shown. The VHB tape will permanently attach to the battery; you may want to purchase quick
release brackets per battery. The orientation of the SD card opening should to point towards the
front of the aircraft.
Figure 11 VHB tape added
Figure 12 Parrot Sunshine sensor added, SD card slot must
point to front of aircraft
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
8
16. Connect the micro USB cable between the camera and Parrot Sunshine Sensor.
Figure 13 Cable connected between Parrot Sequoia camera and Sunshine Sensor
17. Place the two zip tie anchors on one side of the 3DR Solo body.
18. Use zip ties to secure the cord from Sequoia to the Sunshine Sensor.
19. Cut the excess zip ties material with scissors.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
9
DJI Phantom 3 Intended Integration
Parts Included
2x – Parrot Sequoia mounting brackets
2x – Rubber pads
1x – Power and data board
1x – Carbon fiber top mounting plate
1x – Carbon fiber bottom mounting
plate
1x – Parrot Sunshine sensor mast
1x – GoPro Mount
1x – 0.9mm hex key
2x – Zip ties
1x – Screw mount zip tie
3x – M3 x 8 screws
1x – M3 x 12 screw
4x – M3 locking nuts
1x – ¼-20x1/4” screw
2x – Black plastic screws
2x – Black plastic posts
1x – VHB tape square
1x – 2mm hex key
Required Tools
#1 Phillips head screwdriver
#3 Phillips head screwdriver
5.5mm wrench
2x – Flat head screwdrivers
Scissors or wire cutters
Loctite (optional)
Steps
1. Remove DJI Phantom 3 gimbal
1.1. Break the 2 plastic retainer clips going through the dampers and discard
1.2. Carefully remove the camera from the damper balls
1.3. Remove the 2 cables from the camera by depressing the tabs on the connectors and pulling
1.4. Remove white damper balls and save for later use
1.5. Use a 2mm Hex key to remove the 4 screws holding on the gimbal plate, save for later use
WARNING! The Phantom 3 integration kit is intended to be used ONLY with the Phantom 3
Professional and Phantom 3 Advanced aircraft.
DO NOT USE WITH PHANTOM 3 4K OR PHANTOM 3 STANDARD. Use in the Phantom 3 4K or
Phantom 3 Standard will result in damage to your aircraft, Sequoia, or both.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
10
1.6. Remove the rear 6 pin cable from the Phantom 3 body by pulling on the connector
Figure 14 Camera removed from top mount, power and data cables still plugged in
2. Attach the Parrot Sunshine Sensor mast and the power and data board by securing it to the Carbon
fiber top mounting plate with the three M3 x 8mm screws and lock nuts. A #1 Phillips screwdriver
and 5.5mm wrench will be needed.
Figure 15 Screws hand tightened on carbon fiber plate, mast, and power/data board.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
11
3. Use the M3 x 12 screw to secure the screw mount zip tie to the remaining hole and secure with the
remaining M3 nut.
Figure 16 Longer M3 screw being shown securing zip tie and other parts.
4. Secure the power cord as shown with the board mount zip tie.
Figure 17 Power cord shown attached via zip tie
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
12
5. Attach Carbon fiber top mounting plate as shown with the original 4 screws removed in step 1.5.
Make sure to route the wire as shown.
Figure 18 Power cord shown routed through center hole.
6. Connect the power cable from the Phantom 3 to the power and data board.
Figure 19 Phantom 3 power cord plugged into power/data board.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
13
7. Use the 0.9mm hex key to tighten the two set screws on the Sunshine Sensor mast to prevent
rotation during flight.
Figure 20 Tighten set screw at base
Figure 21 Tighten set screw at top
8. Attach the 4 white damper balls onto the Carbon fiber top mounting plate.
Figure 22 Damper balls added
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
14
9. Attach the GoPro mount to the Carbon fiber bottom mounting plate using the ¼-20 x ¼” screw. A
#3 Phillips screwdriver will be needed. It is also recommended threadlocker (not included) is applied
to the screw before it is used to secure the GoPro mount.
Figure 23 GoPro mount attached to lower carbon fiber plate
10. Attach the Carbon fiber bottom mounting plate to the 4 white damper balls.
Figure 24 Bottom plate assembled to damper balls
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
15
11. Slide the black plastic posts through the top of the damper holes at opposite ends.
12. Screw in the black plastic screws into the black plastic posts using 2 flat head screw drivers. Do not
tighten completely, leave enough threads for movement of the mount, 1/8” - 1/4”.
Figure 25 Black plastic screws added for safety
13. Remove adhesive protector from 1 rubber pad.
Figure 26 Backing of pad being removed
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
16
14. Place pad on bracket as shown, repeat for second bracket.
Figure 27 Rubber pad added to bracket - highlighted red for guide
15. Place brackets over Parrot Sequoia camera.
Figure 28 Brackets placed over Parrot Sequoia Camera
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
17
16. Slip the tabs of the brackets into the GoPro mount on the Phantom 3.
Figure 29 Brackets slid into GoPro mount
17. Insert the GoPro mount thumb screw into the mount and position camera as necessary.
Figure 30 Thumbscrew added
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
18
18. Attach the VHB tape to the top of the Parrot Sunshine Sensor mast.
19. Attach either the Parrot Sunshine sensor or the Parrot Sunshine Sensor mount to the VHB tape.
19.1. If the Parrot Sunshine Sensor mount was placed on the mast, insert the Parrot Sunshine
Sensor.
20. Attach the micro-USB cable between the Parrot Sequoia camera and Parrot Sunshine Sensor.
21. Use 2 zip ties to tightly secure the cable to the mast as shown. SD card on Sunshine Sensor should
be facing out from the front of the drone.
Figure 31 Zip ties used to secure USB cord
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
19
22. Using scissors or similar, cut off the excess zip tie material.
Figure 32 Zip ties trimmed down
NOTE: The remaining connector on the power and data board is for communication with the Phantom
3. As of this writing, there is no software support for this feature. The connector is for future
compatibility.
WARNING! The power and data board will get hot and should not be touched during or
after operation. Ensure the board has cooled before touching the area.
Parrot SequoiaTM Integration Kit Instructions: 3DR Solo and DJI Phantom 3
20
Parrot SequoiaTM Integration Kit Instructions by MicaSense
The contents of this manual are subject to change without notice
MicaSense, Inc. assumes no liability for incidental or consequential
damages arising from the use of this product, and any claims by a third party.
Copying of the contents of this manual, in whole or in part, as well as the scanner
applications is prohibited under the copyright law.
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
MICASENSE MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, WITH
RESPECT TO MICASENSE ACCESSORIES. MICASENSE DISCLAIMS ANY LIABILITY FOR
INDIRECT, CONSEQUENTIAL, PUNITIVE, OR SPECIAL DAMAGES, INCLUDING WITHOUT
LIMITATION DAMAGES FOR LOST DATA, LOST REVENUE, LOST PROFITS, OR
REPLACEMENT PRODUCT COSTS ARISING OUT OF THE PURCHASE, USE, OR
PERFORMANCE OF THE MICASENSE ACCESSORIES, UNDER ANY THEORY OF LIABILITY,
EVEN IF MICASENSE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
MICASENSE DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, AND DISCLAIMS ANY IMPLIED WARRANTY ARISING FROM
A COURSE OF PERFORMANCE, DEALING, USAGE, OR TRADE PRACTICE. THE PRICE OF
PRODUCTS DISTRIBUTED BY MICASENSE OR ITS AUTHORIZED DEALERS REFLECTS THE
ALLOCATION OF RISK ARISING FROM THE WARRANTY EXCLUSIONS AND THIS
DISCLAIMER AND LIMITATION OF LIABILITY.