39390.pdf

OU

TO

KU

MP

U S

tainless T

ub

ular P

rod

ucts

1151EN

-GB

:4, 2000, ww

w.rcb2.se, Printed in Sw

eden by Edita, 2007

Oct 2

007

www.outokumpu.com/ostpwww.outokumpu.com

Outokumpu is an international stainless steel company. Our vision is to be the undisputed number one in stainless, with success based on operational excellence. Customers in a wide range of industries use our metal products, technologies and services worldwide. We are dedicated to helping our customers gain competitive advantage. Outokumpu Stainless Tubular Products manufactures and sells welded stainless steel tubes, pipes and fi ttings.

Outokumpu Stainless Tubular Products


Product Catalogue2007

Each product in the table of contents is linked to a catalogue target page.

The top blue field with the Outokumpu logotype on each page is linked to the table of contents.

3

Outokumpu Stainless Tubular Products . . . . 4

Outokumpu. . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6

Welded Tubes and Pipes 10

Design and Pressure Guide. . . . . . . . . . . . . . . 11

Process Pipes,

ISO, OT-No:100 . . . . . . . . . . . . . . . . . . . . . . 12

Metric Tru-Bore®, OT-No:110 . . . . . . . . . . 14

ANSI, OT-No:120 . . . . . . . . . . . . . . . . . . . . . 15

Spiral Welded Tubes, OT-No:147 . . . . . . . . . . 18

Hygienic Tubes, OT-No:142, 152, 162, 172 . . 20

Heat Exchanger Tubes, OT-No:153. . . . . . . . . 22

Domestic Water Tubes. . . . . . . . . . . . . . . . . . . 23

Square and Rectangular Tubes,

OT-No:194, 195 . . . . . . . . . . . . . . . . . . . . . . . . . 26

HF-Welded Round Tubes, OT-No:101, 111 . . 27

Butt Weld Fittings . . . . . . . . . . . . . . . . . . . . 28

Elbows

ISO, OT-No:200, 201 . . . . . . . . . . . . . . . . . . 30

ISO, OT-No:205 . . . . . . . . . . . . . . . . . . . . . . 31

Metric Tru-Bore®, OT-No:213, 212,

214, 215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ANSI, OT-No:226 . . . . . . . . . . . . . . . . . . . . . 34

Tees

ISO, OT-No:300, 301, 302, 303 . . . . . . . . . . 35

Metric Tru-Bore®, OT-No:310, 311, 312 . . 40

ANSI, OT-No:320 . . . . . . . . . . . . . . . . . . . . . 43

Reducers

ISO, OT-No:430, 431, 400, 401 . . . . . . . . . . 45

Metric Tru-Bore®, OT-No:410, 411 . . . . . . 48

ANSI, OT-No:420, 421 . . . . . . . . . . . . . . . . . 51

Pressed collars

ISO, OT-No:500 . . . . . . . . . . . . . . . . . . . . . . 52


Weldring necks

ISO, OT-No:502 . . . . . . . . . . . . . . . . . . . . . . 55


Weld-on plate collars

ISO, OT-No:501 . . . . . . . . . . . . . . . . . . . . . . 59


Angle collars

ISO, OT-No:503 . . . . . . . . . . . . . . . . . . . . . . 60


Caps

ISO, OT-No:60 . . . . . . . . . . . . . . . . . . . . . . . 61

Metric Tru-Bore®, OT-No:61 . . . . . . . . . . . 61

ANSI, OT-No:62 . . . . . . . . . . . . . . . . . . . . . . 62

Tube clamps

ISO/Metric, OT-No:74 . . . . . . . . . . . . . . . . . 63

Threaded Fittings 64

Couplings

R-131–LR131UO, OT-No:800 . . . . . . . . . 68

Union-L, OT-No:839 . . . . . . . . . . . . . . . . . . 69

Union-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Bite-ring couplings

R-1321–R-1326, OT-No:810 . . . . . . . . . . 70

Sockets

R-201–R-408, OT-No:801 . . . . . . . . . . . . 74

Nipples

R-206–R-212, R-228, OT-No:802 . . . . . . 78

Plugs

R-235–R-238, OT-No:803 . . . . . . . . . . . . 84

Caps

R-231–R-232, OT-No:804 . . . . . . . . . . . . 86

Nuts

R-216–R-217, OT-No:805 . . . . . . . . . . . . 88

Hose fittings

R-140–R-146 , OT-No:822 . . . . . . . . . . . 89

Tees, elbows and bends

R-221–R-226, OT-No:806 . . . . . . . . . . . . 91

Socket welding fittings

I-131–I-222, OT-No:830, 831, 832, 836 . 94

Technical information 98

Inspection and dimensional standards . . . . . 99

Dimension standards . . . . . . . . . . . . . . . . . . . 102

Stainless steel grades . . . . . . . . . . . . . . . . . . 103

Mechanical and physical properties . . . . . . 104

Material selection and design . . . . . . . . . . . . 105

Certifications and approvals . . . . . . . . . . . . . 107

Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Table of Contents

CAD-support available on

www.outokumpu.com/ostp


4

Operational Excellence

The company Outokumpu Stainless Tubular Products and its 1300 employees, with a network of

distributors in more than 40 countries and its highly modern and cost efficient production lines

guarantees knowledge and experience in welded Tubes and Fittings in stainless steel.

Outokumpu Stainless Tubular Products is a core business within the Outokumpu Group.

The stainless business area can offer the broadest range of stainless steel products on the market.

We can supply customers with a wide variety of grades, dimensions and surface finishes through

our worldwide distribution network of sales offices and service centres.

Nyby

Storfors

VeteliJakobstad

Outokumpu

5

Outokumpu in brief

Outokumpu is an international stainless steel company. Our vision is to be the undisputed number

one in stainless, with success based on operational excellence.

Customers in a wide range of industries – from the process industry and industrial machinery to

building, construction and electrical industry, transportation, electronics and information techno-

logy, as well as catering and households – use our metal products, technologies and services world-

wide. We are dedicated to helping our customers gain competitive advantage.

Outokumpu operates in some 30 countries and employs 8 000 people. In 2006, the Group’s sales

were EUR 6.2 billion, of which some 95% was generated outside Finland. The Group’s headquar-

ters are located in Espoo, Finland. The parent company, Outokumpu Oyj, has been listed on the

Helsinki stock exchange since 1988.

The stainless tubes and fittings operations are organized under the name:

Outokumpu Stainless Tubular Products.

Specifications

6

Welded Tubes and Pipes

EUROPE

EN 10217-7

Welded steel tubes for pressure purposes.

Technical Delivery Conditions – Part 7: Stainless Steel Tubes.

This standard will replace most of the standards for welded stainless tubes and pipes for pressure

purposes within the CEN countries.

It is similar to DIN 17457 and SS 219711.

The standard prescribes 100 % non-destructive testing. This gives a possible design utilization of

100%, and a weld factor z = 1.0. Heat treatment may be omitted if agreed. The standard inspection

is normally in accordance with EN 10204 3.1.

EN 10296-2

Welded circular steel tubes for mechanical and general engineering purposes.

Technical Delivery Conditions - Part 2: Stainless Steel Tubes.

This standard will replace most of the standards for welded stainless tubes and pipes for general

purposes within the CEN countries.

It is similar to DIN 17455 and SS 219716.

Non-destructive testing of the weld is not mandatory. This gives a possible design utilization of

70%, and a weld factor z = 0.7. Heat treatment may be omitted if agreed. The standard inspection

is normally in accordance with EN 10204 3.1. If the base metal is in accordance with EN 10028-7,

and the tube mill is PED-approved, it is possible to use these pipes up to category I.

USA

Welded pipes

ASTM A 312/A 312M Seamless and welded austenitic stainless steel pipe.

This standard contains analysis regulations and strength requirements. In addition, certain regula-

tions of ASTM A 999 apply as regards inspection and tolerances. The scope of the sampling inspec-

tion to be carried out in respect of technological inspection is stated. Hydrostatic or Eddy Current

testing is to be carried out as a 100% inspection. Welding is to be without filler material and the

pipes are to be heat treated.

ASTM A 358/A 358M Electric-fusion-welded austenitic chromium-nickel alloy steel pipe for high

temperature service.

This standard’s class 3 forms the basis for manufacture of 254 SMO. Pipes are welded with filler

material and are subject to 100% radiographic inspection.

Specifications

7

ASTM A 790/A 790 M Seamless and welded ferritic/austenitic stainless steel pipes.

This standard is similar to ASTM A 312, but intended for duplex grades.

ASTM A 928/A 928M Ferritic/austenitic (duplex) stainless steel pipe electric-fusion-welded with

addition of filler metal.

This standard is similar to ASTM A 358, but intended for duplex grades, and A 928 class 3 forms

the basis for our stock standard of 2205. Pipes are welded with filler material and are subject to

100% radiographic inspection.

Welded Tubes

ASTM A 249 Welded austenitic steel boiler superheater heat-exchanger and condenser tubes

ASTM A 269 Seamless and Welded Austenitic Stainless Steel Tubing for General Service

ASTM A 270 Seamless and Welded Austenitic Stainless Steel Sanitary Tubing

ASTM A 789 Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service

Specifications

8

Butt Weld FittingsEurope

EN 10253-3

Butt-welding pipe fittings. Wrought austenitic and austenitic-ferritic (duplex) stainless steels without

specific inspection requirements. Z = 0.7.

EN 10253-4

Butt-welding pipe fittings. Wrought austenitic and austenitic-ferritic (duplex) stainless steels with

specific inspection requirements. Z = 1.0.

According to EN 10253-4 OSTP deliver normally Type A fittings as standard. (Fittings of Type A

have the same wall thickness at the welding ends and on the body of the fitting. Their resistance to

internal pressure is less than of a pipe with the same specified wall thickness and of the same steel

grade. Fittings of Type B have increased wall thickness at the body of the fitting. They will, in gene-

ral, withstand the same internal pressure as a pipe with the same specified diameter, wall thickness

and of the same steel grade.)

DIN 2609 (Outgoing)

Steel butt-welding pipe fittings. Technical delivery conditions.

This standard will be replaced by the EN-standards above.

USA

ASTM A 403 Wrought austenitic stainless steel piping fittings.

ASTM A 815 Wrought ferritic, duplex, martensitic stainless steel piping fittings.

Threaded FittingsEurope

EN 10241 Steel threaded pipe fittings.

Specifications

9

Welded Tubes and Pipes

10

Welded Tubes

The manufacturing, distribution and sales of welded stainless steel process pipes and heat exchanger tubes,

require that the customers’ needs regarding a safe transport of corrosive, flammable and toxic fluids and gases

must be fulfilled.

Outokumpu Stainless Tubular Products with tube mills in Torshälla, Fagersta, Storfors, Jakobstad, and

Wildwood offers from the extensive stock programme more than 600 different articles for all types of

applications within the process industries.

Manufacturing units with in-line equipment of the highest technology in combination with a QS according

to EN ISO 9001:2000 form the base for high quality. All units are approved according to the European

Pressure Equipment Directive PED 97/23/EC and certified by TÜV to AD 2000-Merkblatt W0, which

fulfils the highest quality requirements from the Process industries.

This is valid also for tubes that are used in hygienic applications within the food, dairy and pharmaceutical

industries as well as for gas and water installations. Also for these applications we can offer the right product

that requires high demands on the surfaces.

We can also offer an interesting programme of square, rectangular and round tubes for construction and

decoration. An extensive stock programme together with Outokumpus’ distribution net secures a high

availability and fast delivery service for any application.

If thin or thick, big or small, long or short, corrosion-, acid- or heat resistant, – indifferent of application

– Outokumpu Stainless Tubular Products always has the right offer for your needs.

Process Pipes

This type of piping is used primarily in the pulp, paper, chemical and petrochemical industries. Pipes in

chemical tankers, and for handling of water such as in pipelines, sewage- and desalination plants, are yet

other important applications.

We stock a wide range of pipes in ISO, ANSI and Metric dimensions.

Available stocked dimensions are:

OD: 17.1-808 mm

Wall thickness: ≤9.53 mm

Manufacturing Dimension range:

OD: 17.1-2032 mm (NPS 3/8-80)

Wall thickness: ≤50.8 mm (-2”)

11

Design and Pressure Guide

Example 1Which dimension is necessary for a 1.4307-pipe with DN 450 and a design pressure of 16 bar at 20˚C?Answer:For Metric Tru-Bore with z = 0,7 460 x 5 is necessaryFor Metric Tru-Bore with z = 1 456 x 3 is OK.For ISO with z = 0,7 457 x 5 is necessaryFor ISO with z = 1 457 x 3 is OK.Example 2Which dimension is necessary for a 1.4307-pipe with DN 450 and a design pressure of 16 bar including resistance to inside vacuum at 20˚C?Answer:For Metric Tru-Bore 460 x 5 is necessaryFor ISO 457 x 5 is necessary

1,5 2 2,5 3 4 5 6 7 8 9 10

1,0 - 125 25

1,0 150 25 33 42 50

1,0 200 19 25 31 37 50

1,0 250 15 20 25 30 40 50

1,0 300 16 21 25 33 42

1,0 350 18 21 25 36 43

1,0 400 19 25 31 37 44

1,0 450 16 22 28 33 38 44 49 54

1,0 500 15 20 25 30 35 40 45 50

0,7 450 11 15 19 23 25 31 35 38

0,7 500 10 14 17 21 25 28 31 35

0,7 600 8 11 14 17 20 23 25 29

0,7 700 7 10 12 15 17 20 22 25

0,7 800 6 8 11 13 15 17 19 22

0,7 900 6 7 9 11 13 15 17 19

0,7 1000 7 8 10 12 14 15 17

0,7 1100 6 8 9 11 12 14 16

0,7 1200 6 7 8 10 11 13 14

0,7 1300 6 8 9 11 12 13

0,7 1400 6 7 8 10 11 12

0,7 1500 6 7 8 9 10 11

0,7 1600 6 7 8 10 11

Weldfactor

MetricID

Wall thickness, mm

2 2,6 3 3,2 3,6 4 5 6 7 8 9 10

1,0 - 159 25

1,0 168,3 30 39 45 48 55 61 761,0 219,1 23 30 35 37 42 47 58 701,0 273,0 18 24 28 30 33 37 47 56 661,0 323,9 15 20 23 25 28 31 39 47 55 631,0 355,6 18 21 23 26 29 36 43 50 57 651,0 406,4 16 19 20 22 25 31 38 44 50 57 631,0 457 16 18 20 22 28 33 39 45 50 561,0 508 15 16 18 20 25 30 35 40 45 500,7 457 11 12 14 15 19 23 27 31 35 390,7 508 10 11 12 14 17 21 24 28 31 350,7 610 8 9 10 11 14 17 20 23 26 290,7 711 7 8 9 10 12 15 17 20 22 250,7 813 6 7 8 8 11 13 15 17 19 220,7 914 7 7 9 11 13 15 17 190,7 1016 6 7 8 10 12 14 16 170,7 1118 6 8 9 11 12 14 160,7 1219 7 8 10 11 13 140,7 1321 6 8 9 10 12 130,7 1422 6 7 8 10 11 120,7 1524 7 8 9 10 110,7 1626 6 7 8 10 11

6-9.9 bar inside pressure10-15.9 bar inside pressure16-24.9 bar inside pressureLimit for inside vacuum. Wall>0,01xOD

Weldfactor

ISO OD Wall thickness, mm

Maximum Allowable Working Pressure at 20˚C, according to EN 13480

Grades 1.4306, 1.4307 and 1.4541For grades 1.4404, 1.4432, 1.4435, 1.4438, 1.4539 and 1.4571 multiply ”bar-value” with 1,08.

12

OT-No.: 100EN ISO 1127

10 17,2 0,6315 18,0 0,66 0,80

19,0 0,70 0,8520,0 0,74 0,90

21,3 0,79 0,97 1,09 1,2220 22,0 0,82 1,00 1,13 1,26

25,0 0,94 1,15 1,31 1,4625,4 0,95 1,17 1,33 1,48

26,9 1,01 1,25 1,42 1,58 1,7425 30,0 1,14 1,40 1,59 1,78 1,97

31,8 1,21 1,49 1,70 1,90 2,1032,0 1,22 1,50 1,71 1,91 2,11

33,7 1,28 1,59 1,81 2,02 2,23 2,30 2,4432 35,0 1,34 1,65 1,88 2,11 2,33 2,40 2,55

38,0 1,46 1,80 2,05 2,30 2,55 2,63 2,7940,0 1,54 1,90 2,17 2,43 2,69 2,78 2,95

42,4 1,63 2,02 2,31 2,59 2,87 2,96 3,14 3,4940 44,5 1,72 2,13 2,43 2,72 3,02 3,11 3,31 3,68

48,3 1,87 2,32 2,65 2,97 3,29 3,40 3,61 4,0350 51,0 1,98 2,45 2,80 3,15 3,49 3,60 3,83 4,27

54,0 2,10 2,60 2,97 3,34 3,71 3,83 4,07 4,5057,0 2,22 2,75 3,15 3,54 3,92 4,05 4,31 4,81 5,30

60,3 2,35 2,92 3,34 3,75 4,16 4,30 4,57 5,11 5,6365 63,5 2,48 3,08 3,52 3,96 4,40 4,54 4,83 5,39 5,95

70,0 2,74 3,40 3,89 4,38 4,87 5,03 5,35 5,98 6,6076,1 2,98 3,71 4,25 4,79 5,31 5,49 5,84 6,53 7,21

80 82,5 3,24 4,03 4,61 5,20 5,77 5,97 6,35 7,10 7,8588,9 3,50 4,35 4,98 5,61 6,24 6,45 6,86 7,68 8,49

100 101,6 4,00 4,98 5,71 6,44 7,16 7,40 7,88 8,82 9,78108,0 4,26 5,30 6,08 6,85 7,63 7,89 8,39 9,40 10,4

114,3 4,51 5,62 6,44 7,26 8,09 8,36 8,89 9,97 11,0125 133,0 5,26 6,55 7,52 8,49 9,45 9,77 10,4 11,7 12,9

139,7 5,53 6,89 7,90 8,91 9,92 10,3 10,9 12,3 13,6150 159,0 6,30 7,85 9,02 10,2 11,3 11,7 12,5 14,0 15,5

168,3 6,67 8,32 9,55 10,8 12,0 12,4 13,2 14,8 16,4200 219,1 10,9 12,5 14,1 15,7 16,2 17,3 19,4 21,5250 273,0 13,6 15,6 17,6 19,6 20,3 21,6 24,3 26,9300 323,9 16,1 18,5 20,9 23,3 24,1 25,7 28,8 32,0350 355,6 22,9 25,6 26,5 28,2 31,7 35,2400 406,4 26,3 29,3 30,3 32,3 36,3 40,3450 457 32,9 34,1 36,3 40,8 45,3500 508 36,6 37,9 40,4 45,4 50,4600 610 44,0 45,6 48,6 54,6 60,6700 711 70,7800 813 81,0900 914 91,0

1000 1016 1011100 1118 1111200 1219 122

Series Wall thickness mm

DN 1 2 3 1,6 2,0 2,3 2,6 2,9 3,0 3,2 3,6 4,0

OD, mm Weight kg/m

Process Pipes

The table shows our production programme within the ISO 1127 standard.Selected ISO-dimensions are stocked in following grades: EN 1.4301*, 1.4307, 1.4404, 1.4432, 1.4541 and 1.4571.

DN10-DN500 in accordance with EN 10217-7 Tmax 6,0 mm.DN125-DN1200 in accordance with EN 10296-2 produced from plate.

*) Only HF-welded tubes.

Process Pipes

OT-No.: 100EN ISO 1127

10 17,215

19,020,0

21,320

25,0

26,925

31,832,0

33,732

38,040,0

42,440

48,350 51,0

57,060,3

65 63,570,0

76,180

88,9 9,50100 101,6 10,9

108,0 11,6114,3 12,4 13,7

125 133,0 14,5 16,0139,7 15,2 16,8 20,1 23,5 26,4 28,8 32,4

150 159,0 17,4 19,3 23,0 27,0 30,2 33,1 37,3168,3 18,4 20,4 24,4 28,6 32,1 35,1 39,6 43,3

200 219,1 24,2 26,8 32,0 37,7 42,2 46,3 52,3 57,3 64,6250 273,0 30,2 33,5 40,1 47,2 53,0 58,2 65,8 72,1 81,4 91,9300 323,9 36,0 39,9 47,7 56,3 63,2 69,4 78,5 86,1 97,3 110350 355,6 39,5 43,8 52,5 61,9 69,6 76,3 86,5 94,8 108 121400 406,4 45,2 50,2 60,1 70,9 79,7 87,5 99,1 109 123 139450 457 50,9 56,5 67,7 79,9 89,8 98,7 112 123 139 157500 508 56,7 62,9 75,3 89,0 100 110 125 137 155 175600 610 68,2 75,7 90,6 107 121 132 150 165 187 212700 711 79,5 88,4 106 125 141 155 175 193 218 247800 813 91,0 101 121 143 161 177 201 221 250 284900 914 102 114 136 161 181 199 226 248 282 320

1000 1016 114 126 152 179 202 222 252 277 3141100 1118 125 139 167 197 222 244 277 305 3461200 1219 137 152 182 215 242 266 302 332

Series Wall thickness mm

DN 1 2 4,5 5,0 6,0 7,1 8,0 8,8 10 11 12 14

OD, mm Weight kg/m

13

The table shows our production programme within the ISO 1127 standard.Selected ISO-dimensions are stocked in following grades: EN 1.4301*, 1.4307, 1.4404, 1.4432, 1.4541 and 1.4571.

DN10-DN500 in accordance with EN 10217-7 Tmax 6,0 mm.DN125-DN1200 in accordance with EN 10296-2 produced from plate.

*) Only HF-welded tubes.

14

Process Pipes

OT-No.: 110Metric Tru-Bore®

Selected Metric Tru-Bore®-dimensions are stocked in following grades: EN 1.4307, 1.4404, 1.4432, 1.4541 and 1.4571DN10-DN500 in accordance with EN 10217-7 Tmax 6,0 mm.

DN125-DN1600 in accordance with EN 10296-2 produced from plate.*) ISO-dimension

15 18 0,620 0,801

15 18 0,62 0,8020 0,70 0,90 1,10

20 22 0,77 1,00 1,2223 0,81 1,05 1,2825 0,88 1,15 1,41

25 28 1,00 1,30 1,6030 1,07 1,40 1,72 2,0332 1,15 1,50 1,85 2,1833 1,18 1,55 1,91 2,25

32 35 1,26 1,65 2,03 2,4038 1,37 1,80 2,22 2,6340 1,45 1,90 2,35 2,78

40 43 1,5644,5* 1,62 2,13 2,63 3,12

50 1,82 2,40 2,97 3,5350 51 1,86 2,45 3,04 3,61

53 1,9354 1,97 2,60

57* 2,08 2,75 3,41 4,06 5,3165 63,5* 2,33 3,08 3,82 4,55 5,96

68 2,50 3,3169 3,36

70* 2,57 3,41 4,23 5,03 6,61

Inside Wall thickness mm

diameter 1,5 2,0 2,5 3,0 4,0 5,0 6,0 8,0 10 12

DN mm Weight kg/m

80 80 3,06 4,11 5,16 6,24 100 100 3,81 5,11 6,42 7,74 10,4125 125 4,75 6,36 7,97 9,62 12,9150 150 5,69 7,61 9,55 11,5 15,4 19,4 23,4 31,6 40,0 48,6200 200 7,57 10,1 12,7 15,3 20,4 25,7 31,0 41,6 52,5 63,6250 250 9,45 12,6 15,8 19,0 25,4 31,9 38,4 51,6 65,0 78,7300 300 11,3 15,1 18,9 22,8 30,5 38,2 45,9 61,6 77,6 93,7350 350 13,2 17,6 22,1 26,5 35,5 44,4 53,4 71,6 90,1 109400 400 30,3 40,5 50,7 60,9 81,7 103 124450 450 34,0 45,5 57,0 68,4 91,7 115 139500 500 37,8 50,5 63,2 76,0 102 128 154600 600 45,3 60,5 75,8 91,1 122 153 184700 700 52,8 70,5 88,3 106 142 178 214800 800 60,3 80,5 101 121 162 203 244900 900 67,8 90,6 113 136 182 228 274

1000 1000 75,4 101 126 151 202 253 3041100 1100 82,9 111 138 166 222 278 3341200 1200 90,4 121 151 181 242 303 3641300 1300 97,9 131 163 196 262 3281400 1400 105 141 176 211 282 3531500 1500 113 151 188 226 3021600 1600 120 161 201 241 322

Outside Wall thickness mm

diameter 1,5 2,0 2,5 3,0 4,0 5,0 6,0 8,0 10 12

DN mm Weight kg/m

Process Pipes

OT-No.: 120ANSI/ASME B36.19M 2004

10 3/8 17,1 1,65 0,6415 1/2 21,3 1,65 0,81 2,11 1,01 2,77 1,2920 3/4 26,7 1,65 1,03 2,11 1,30 2,87 1,71 3,91 2,2325 1 33,4 1,65 1,31 2,77 2,12 3,38 2,54 4,55 3,2932 1 1/4 42,2 1,65 1,68 2,77 2,73 3,56 3,44 4,85 4,5440 1 1/2 48,3 1,65 1,93 2,77 3,16 3,68 4,11 5,08 5,5050 2 60,3 1,65 2,42 2,77 3,99 3,91 5,52 5,54 7,6065 2 1/2 73,0 2,11 3,74 3,05 5,34 5,16 8,76 7,01 11,680 3 88,9 2,11 4,58 3,05 6,56 5,49 11,5 7,62 15,5

100 3 1/2 101,6 2,11 5,26 3,05 7,53 5,74 13,8 8,08 19,04 114,3 2,11 5,93 3,05 8,49 6,02 16,3 8,56 22,7

125 5 141,3 2,77 9,61 3,40 11,7 6,55 22,1 9,53 31,4150 6 168,3 2,77 11,5 3,40 14,0 7,11 28,7 10,97 43,2200 8 219,1 2,77 15,0 3,76 20,3 8,18 43,2 12,70 65,6250 10 273,0 3,40 23,0 4,19 28,2 9,27 61,2 12,70 82,8300 12 323,9 3,96 31,7 4,57 36,5 9,53 75,0 12,70 98,9350 14 355,6 3,96 34,9 4,78 42,0 9,53 82,6 12,70 109400 16 406,4 4,19 42,2 4,78 48,1 9,53 94,7 12,70 125450 18 457 4,19 47,5 4,78 54,1 9,53 107 12,70 141500 20 508 4,78 60,2 5,54 69,7 9,53 119 12,70 157550 22 559 4,78 66,3 5,54 76,8 9,53 131 12,70 174600 24 610 5,54 83,8 6,35 96,0 9,53 143 12,70 190

26 660 9,53 155 12,70 206700 28 711 9,53 167 12,70 222

30 762 6,35 120 7,92 150 9,53 180 12,70 238800 32 813 9,53 192 12,70 254

34 864 9,53 204 12,70 271900 36 914 9,53 216 12,70 287

38 965 9,53 228 12,70 3031000 40 1016 9,53 240 12,70 319

42 1067 9,53 252 12,70 3351100 44 1118 9,53 264 12,70 351

46 1168 9,53 276 12,70 3671200 48 1219 9,53 289 12,70 384

…* ...52 1321 9,53 313 12,70 41654 1372 9,53 325 12,70 43256 1422 9,53 337 12,70 44860 1524 9,53 361 12,70 48164 1626 9,53 386 12,70 51368 1727 9,53 410 12,70 54572 1829 9,53 434 12,70 57776 1930 9,53 458 12,70 61080 2032 9,53 483 12,70 642

DN NPS OD mm Sch 5S/5 Sch 10S Sch 40S/STD Sch 80S/XS

wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m

The table shows our production programme within the ANSI B36.19 standard.Selected ANSI-dimensions are stocked in following grades: EN 1.4307/304L, 1.4404/316L, 1.4432/316hMoL, 1.4462/2205 and 1.4547/254 SMO.

In accordance with ASTM A-312 *) Not standardised schedules within our product range

15

16

Process Pipes

ASME B36.10M 2004

10 3/8 17,1 1,65 0,6415 1/2 21,3 2,11 1,01 2,41 1,14 2,77 1,2920 3/4 26,7 2,11 1,30 2,41 1,47 2,87 1,7125 1 33,4 2,77 2,12 2,90 2,21 3,38 2,5432 1 1/4 42,2 2,77 2,73 2,97 2,92 3,56 3,4440 1 1/2 48,3 2,77 3,16 3,18 3,59 3,68 4,1150 2 60,3 2,77 3,99 3,18 4,55 3,91 5,5265 2 1/2 73,0 3,05 5,34 4,78 8,16 5,16 8,7680 3 88,9 3,05 6,56 4,78 10,1 5,49 11,5

100 3 1/2 101,6 3,05 7,53 4,78 11,6 5,74 13,8100 4 114,3 3,05 8,49 4,78 13,1 6,02 16,3125 5 141,3 3,40 11,7 6,55 22,1150 6 168,3 3,40 14,0 7,11 28,7200 8 219,1 3,76 20,3 6,35 33,8 7,04 37,4 8,18 43,2 10,31 53,9250 10 273,0 4,19 28,2 6,35 42,4 7,80 51,8 9,27 61,2 12,70 82,8300 12 323,9 4,57 36,5 6,35 50,5 8,38 66,2 10,31 80,9 14,27 111350 14 355,6 6,35 55,5 7,92 68,9 9,53 82,6 11,13 96,0 15,09 129400 16 406,4 6,35 63,6 7,92 79,0 9,53 94,7 12,70 125 16,66 163450 18 457 6,35 71,6 7,92 89,0 11,13 124 14,27 158 19,05 209500 20 508 6,35 79,7 9,53 119 12,70 157 15,09 186 20,62 252550 22 559 6,35 87,9 9,53 131 12,70 174 22,23 299600 24 610 6,35 96,0 9,53 143 14,27 213 17,48 259 24,61 361

26 660 7,92 129 12,70 206700 28 711 7,92 139 12,70 222 15,88 276

30 762 7,92 150 12,70 238 15,88 297800 32 813 7,92 160 12,70 254 15,88 317 17,48 348

34 864 7,92 170 12,70 271 15,88 337 17,48 370900 36 914 7,92 180 12,70 287 15,88 357 19,05 427

...* ... ... ... ...38 965 7,92 190 14,27 340 15,88 377 17,48 415 19,05 451

1000 40 1016 7,92 200 14,27 358 15,88 398 17,48 437 19,05 47642 1067 11,13 294 14,27 376 15,88 418 17,48 459 19,05 500

1100 44 1118 11,13 308 14,27 394 15,88 438 17,48 482 19,05 52446 1168 11,13 322 14,27 412 15,88 458 17,48 504 19,05 548

1200 48 1219 11,13 337 14,27 430 15,88 478 17,48 526 19,05 57252 1321 11,13 365 14,27 467 15,88 519 17,48 570 19,05 62154 1372 11,13 379 14,27 485 15,88 539 17,48 593 19,05 64556 1422 11,13 393 14,27 503 15,88 559 17,48 615 19,05 66960 1524 11,13 422 14,27 539 15,88 600 17,48 659 19,05 71864 1626 11,13 450 14,27 576 15,88 640 17,48 704 19,05 76668 1727 11,13 478 14,27 612 15,88 680 17,48 748 19,05 81572 1829 11,13 507 14,27 648 15,88 721 17,48 793 19,05 86376 1930 11,13 535 14,27 684 15,88 761 17,48 837 19,05 91180 2032 11,13 563 14,27 721 15,88 802 17,48 882 19,05 960

DN NPS OD mm Sch 10 Sch 20 Sch 30 Sch 40 Sch 60

wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m

The table shows our production programme within the ASME B36.10 standard.Selected ANSI-dimensions are stocked in following grades: EN 1.4307/304L, 1.4404/316L, 1.4432/316hMoL, 1.4462/2205 and 1.4547/254 SMO.

In accordance with ASTM A-312 *) Not standardised schedules within our product range

OT-No.: 120

Process Pipes

ASME B36.10M 2004

10 3/8 17,115 1/2 21,320 3/4 26,7 3,91 2,2325 1 33,4 4,55 3,2932 1 1/4 42,1 4,85 4,5440 1 1/2 48,3 5,08 5,5050 2 60,3 5,54 7,6065 2 1/2 73,0 7,01 11,680 3 88,9 7,62 15,5

100 3 1/2 101,6 8,08 19,0100 4 114,3 8,56 22,7125 5 141,3 9,53 31,4150 6 168,3 10,97 43,2200 8 219,1 12,70 65,6 15,09 77,1 18,26 91,8250 10 273,0 15,09 97,4 18,26 116 21,44 135 25,40 157 28,58 175 25,40 157300 12 323,9 17,48 134 21,44 162 25,40 190 28,58 211 33,32 242 25,40 190350 14 355,6 19,05 161 23,83 198 27,79 228 31,75 257 35,71 286 25,40 210400 16 406,4 21,44 207 26,19 249 30,96 291 36,53 338 40,49 371 25,40 242450 18 457 23,83 258 29,36 314 34,93 369 39,68 415 45,24 466 25,40 274500 20 508 26,19 316 32,54 387 38,10 448 44,45 516 50,01 573 25,40 307550 22 559 28,58 380 34,93 458 41,28 535 47,63 610 25,40 339600 24 610 30,96 449 38,89 556 46,02 650 25,40 372

...* ... ... ... ... ...26 660 30,96 488 38,10 593 41,28 640 44,45 685 50,80 775 25,40 404

700 28 711 30,96 527 38,10 642 41,28 692 44,45 742 50,80 840 25,40 43630 762 30,96 567 38,10 691 41,28 745 44,45 799 50,80 905 25,40 468

800 32 813 30,96 606 38,10 739 41,28 798 44,45 855 50,80 969 25,40 50134 864 30,96 646 38,10 788 41,28 850 44,45 912 50,80 1034 25,40 533

DN NPS OD mm Sch 80 Sch 100 Sch 120 Sch 140 Sch 160 Sch XXS

wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m wt mm kg/m

The table shows our production programme within the ASME B36.10 standard.In accordance with ASTM A-312

*) Not standardized schedules within our product range

OT-No.: 120

ANSI / ASME B36.19 Stainless steel pipe NPS 1 / 8”– 30”. Schedule SS, 10S, 40S and 80S. Nominal diameters, wall thicknesses and wall thickness tolerances. The schedule numbers (e.g. 40) indicate different wall thickness series. The letter ”S” in the designation stands for stainless material.

As ANSI / ASME B36.19 is not complete, the standard for carbon steel tubes ASME B36.10 is used as a complement for stainless tubes. In this standard there is no ”S” after the schedule figure. The sizes are stated in the following standard published by the American National Standards Institute.

ASME B36.10 Welded and seamless wrought steel pipe NPS 1 / 8”– 80”. Schedule 10 –160. Nominal diameters, wall thicknesses and weight per length unit.The ANSI system is a national system that in applied throughout the world, and particularly in certain areas, especially within the petrochemical and offshore industries.

17

Spiral Welded Tubes

18

Spiral Welded Tubes

The fabrication method allows great flexibility in the manufacture of sizes outside the standard stock

programme.

Consideration will always be given to customers’ request for any especially close tolerance

requirements.

Dimension range ID 73-400 mm

Wall thickness 0,5-4,5 mm

with the main emphasis on the very thin wall dimensions

Tolerances Outside diameter OD ± 0,5%

Wall thickness T ± 10% (standard)

Standard length 6,0 m ± 10 mm

Deviation from straightness max 0,5 mm /m

Grade EN 1.4404

Weld factor 0.7

*) Acc. to PED 97/23/EC annex 2 diagram 9

Spiral Welded Tubes

OT-No.: 147Spiral Welded Tubes. Stock standard

75,0x1,0 3,1 1,85 T3607510

82,0x1,0 2,8 2,03 T3608210

90,0x1,0 2,6 2,23 T3609010

102,0x1,0 2,2 2,53 T3610210

110,0x1,0 2,1 2,73 T3611010

122,0x1,0 1,9 3,03 T3612210

127,0x1,0 1,8 3,16 T3612710

152,0x1,0 1,5 3,78 T3615210

177,0x1,0 1,3 4,41 T3617710

202,0x1,0 1,1 5,03 T3620210

252,0x1,0 0,9 6,29 T3625210

302,0x1,0 0,7 7,54 T3630210

103,0x1,5 3,4 3,81 T3610315

114,3x1,5 3,0 2,80 T3611415

123,0x1,5 2,8 4,56 T3612315

128,0x1,5 2,7 4,75 T3612815

153,0x1,5 2,2 5,69 T3615315

178,0x1,5 1,9 6,63 T3617815

203,0x1,5 1,7 7,57 T3620315

228,0x1,5 1,5 8,51 T3622815

253,0x1,5 1,3 9,45 T3625315

278,0x1,5 1,2 10,4 T3627815

303,0x1,5 1,1 11,3 T3630315

353,0x1,5 0,9 13,2 T3635315

403,0x1,5 0,8 15,1 T3640315

404,0x2,0 1,1 20,1 T3640420

19

Dim. Design Pressure Weight Article code

DxT (MPa)* kg/m EN 1.4404

Hygienic Tubes

20

OT-No.: 142 and 172Dimension standards DIN 11850

18,0x1,0 0,43 180 X X X X19,0x1,5 0,66 180 X X X X22,0x1,0 0,53 180 X X X X23,0x1,5 0,81 132 X X X X28,0x1,0 0,68 408 X X X X29,0x1,5 1,03 192 X X X X34,0x1,0 0,83 252 X X X X35,0x1,5 1,26 132 X X X X40,0x1,0 0,98 528 X X X X41,0x1,5 1,48 168 X X X X52,0x1,0 1,28 528 X X X X53,0x1,5 1,93 144 X X X X70,0x2,0 3,41 288 X X X X85,0x2,0 4,16 180 X X X X

104,0x2,0 5,11 120 X X X X129,0x2,0 6,36 72 0 0 0 0154,0x2,0 7,61 54 0 0 0 0

ODxWT Weight Std-crate EN 1.4307 EN 1.4404

BC BD BC BD

mm kg/m meter pickled outs.brushed pickled outs.brushed

0 = unannealed

Hygienic Tubes

Tubes for hygienic applications are manufactured from cold-rolled strip with controlled composition,

narrow tolerances and high surface finish. The tubes are produced in welding lines specially designed

regarding forming technique, control of welding, cold-working weld bead and calibrated. The tubes

are heat-treated for optimum forming and corrosion resistance.

Technical information

Approvals PED 97/23/EC, AD 2000 W0/ TRB 100

Grades The tubes are stocked in the grades EN 1.4307/TP 304L and EN 1.4404/TP 316L.

Other grades on request.

Specifications Stock material is produced according to the following standards:

1. DIN 11850 including sizes acc. to SMS 3008 tested acc. to EN 10217-7 TC1

2. ASTM A 269/A 270 tested acc. to ASTM A 1016

Grade TP 316L has sulphur content 0.005-0.017 %

3. Other standards on request

Execution All tubes except 129x2 and 154x2 are annealed.

Surfaces Execution (DIN 11850) Roughness

BC Annealed/pickled Strip Ra max 0.8 µm

BD Annealed/outside ground Weld area Ra max 1.6 µm

Outside ground surface Ra max 1.0 µm

Length The random length is 6 m for all dimension standards.

Hygienic Tubes

21

OT-No.: 152Imperial sizes ASTM A269/A270

1x0,064 25,4x1,63 0,97 713 X X X X

1 1/2x0,064 38,1x1,63 1,49 622 X X X X

2x0,064 50,8x1,63 2,01 439 X X X X

2 1/2x0,064 63,5x1,63 2,53 317 X X X X

3x0,064 76,2x1,63 3,04 280 X X X X

4x0,064 101,6x1,63 4,08 183 X X X X

4x0,080 101,6x2,03 5,06 152 X X X X

304L 316L

ODxt ODxt Weight Std-crate annealed annealed annealed annealed

inch mm kg/m meter pickled outs.brushed pickled outs.ground

OT-No.: 142 and 172Sizes not included in DIN 11850

18,0x1,5 0,62 180 X X X X22,0x1,5 0,77 180 X X X X28,0x1,5 1,00 408 X X X X34,0x1,5 1,22 252 X X X X40,0x1,5 1,45 528 X X X X52,0x1,5 1,90 528 X X X X


BC BD BC BD


OT-No.: 162SMS 3008

25,0x1,2 0,72 300 X X X X32,0x1,2 0,93 168 X X X X38,0x1,2 1,11 612 X X X X51,0x1,2 1,50 528 X X X X63,5x1,6 2,48 276 X X X X76,0x2,0 3,71 234 X X X X76,1x1,6 2,99 234 X X X X

101,6x2,0 4,99 120 X X X X


BC BD BC BD


Heat Exchanger Tubes

22

OT-No.:153

Heat Exchanger Tubes

Typical applications are coolers, heaters, evaporators, condensers and recuperators in harsh environments.

The tubes are supplied according to appropriate standards as well as customer specifications in a large variety

of steel grades and dimensions. They are made from strips, welded without filler metal, delivered in annealed

condition in fixed lengths. Specific requirements on execution, tolerances, lengths, mechanical and corrosion

properties are offered on request.


Approvals PED 97/23/EC and AD2000 W0/TRB100.

Grades Austenitic and duplex grades.

Sizes Standard metric, imperial, and ISO outside diameters and wall thicknesses, in the range

OD 18-51 mm, WT 1,0-2,11 mm and in max lengths of 18 meter.

Specifications AD2000-W2, EN 10217-7, ASTM A 249, A 269, A 789.

Execution Longitudinally welded tubes, annealed, pickled and max height of inside weld = 0.15 mm.

Other executions on request.

23

Domestic Water Tubes

Domestic Water Tubes

These tubes are considered as hygienic tubes and manufactured at the Fagersta plant, specialised for

production of tubes with high surface requirements. The tubes are mainly used in connection with press

fittings for domestic tap water installations and also for sprinkler- and air condition systems.


Approvals DVGW No DW-7301 BP0078

SITAC No 0114/04

Grades EN 1.4404. Other grades on request

Specifications Stock material is produced according to the following standards:

DVGW Arbeitsblatt GW 541 / EN 10312

Execution Line pipes:

Longitudinally welded tubes, bright annealed, weld cold worked or as welded,

outside polished.

Tubes for production of fittings:

As above and annealed to mechanical properties suitable for production of fittings.

Inner weld bead is removed by cold work.

Length The random length is 6 m for all dimension standards.

24

Square and Rectangular Tubes


Square and rectangular tubes are used in various

industries:

• Building and construction

• Machine and process equipment builders

• Decoration

• Automotive

HF-welding – speed and precision

The use of High Frequency welding techniques in the manufacturing of stainless steel tubes represents

state-of-art technology. It ensures a very fast production speed and excellent precision.

The weld bead is removed by smoothing or planning externally. Increased efficiency and capacity

reduce delivery times and make deliveries even more flexible. Speed guarantees that the unit prices

remain stable, and that’s why our products are even more competitive than before.

Available grades are EN 1.4301/304, EN 1.4307/304L, EN 1.4404/316L and the ferritic grade

EN 1.4003.

Random length 6 m.

Tolerances

- length +5 -0 mm

- wall thickness ± 10% or min 0,2 mm

- a and b outside measure ± 1%, at least 0,3 mm

- straightness tolerance max 2 mm/m

- perpendicularity of sides 90° ± 1°

- radius of corner curvature ± 20%

Outside finishes

- as welded

- descaled

- brushed

- polished

- Grit 240 and 320

A special product brochure, 1226EN-GB2 about square, rectangular and HF-welded round tubes

is available.

25

26


OT-No.: 194Square Tubes

20x20x1,0 0,61 50420x20x1,2 0,73 50420x20x1,5 0,90 50420x20x2,0 1,18 50425x25x1,0 0,77 50425x25x1,2 0,92 50425x25x1,5 1,14 50425x25x2,0 1,49 50425x25x3,0 2,17 50430x30x1,0 0,93 36030x30x1,2 1,11 36030x30x1,5 1,38 36030x30x2,0 1,81 36030x30x2,5 2,24 36030x30x3,0 2,65 36035x35x1,0 1,09 27035x35x1,2 1,30 27035x35x1,5 1,62 27035x35x2,0 2,13 27035x35x3,0 3,12 27040x40x1,0 1,25 28840x40x1,2 1,50 28840x40x1,5 1,86 28840x40x2,0 2,45 28840x40x2,5 3,03 28840x40x3,0 3,60 28850x50x1,2 1,88 21650x50x1,5 2,34 21650x50x2,0 3,09 21650x50x2,5 3,83 21650x50x3,0 4,56 14460x60x1,5 2,81 21660x60x2,0 3,73 21660x60x3,0 5,51 14460x60x4,0 7,25 14470x70x2,0 4,36 12070x70x3,0 6,47 12070x70x4,0 8,53 12080x80x2,0 5,00 12080x80x3,0 7,43 12080x80x4,0 9,80 9080x80x5,0 12,13 90

100x100x2,0 6,40 120100x100x3,0 9,34 90100x100x4,0 12,35 60100x100x5,0 15,31 60

Dimensions Weight Std bundle

a x a x t kg/m m

OT-No.: 195Rectangular Tubes

40x20x1,0 0,93 38440x20x1,2 1,11 38440x20x1,5 1,38 38440x20x2,0 1,81 38440x20x3,0 2,65 38440x30x1,0 1,09 28840x30x1,2 1,30 28840x30x1,5 1,62 28840x30x2,0 2,13 28840x30x3,0 3,12 28850x25x1,0 1,19 28850x25x1,2 1,42 28850x25x1,5 1,76 28850x25x2,0 2,32 28850x25x3,0 3,41 28850x30x1,0 1,25 25250x30x1,2 1,50 25250x30x1,5 1,86 25250x30x2,0 2,45 25250x30x3,0 3,60 25250x40x2,0 2,77 21650x40x3,0 4,08 21660x30x1,0 1,41 24060x30x1,2 1,69 24060x30x1,5 2,10 24060x30x2,0 2,77 24060x30x2,5 3,43 24060x30x3,0 4,08 24060x40x1,2 1,88 21060x40x1,5 2,34 21060x40x2,0 3,09 21060x40x2,5 3,83 18060x40x3,0 4,56 15080x40x1,5 2,81 21680x40x2,0 3,73 12080x40x3,0 5,51 12080x40x4,0 7,25 12080x60x2,0 4,36 12080x60x3,0 6,47 12080x60x4,0 8,53 120

100x40x2,0 4,36 120100x40x3,0 6,47 120100x40x4,0 8,53 120100x50x2,0 4,67 120100x50x3,0 6,97 120100x50x4,0 9,16 120100x50x5,0 11,32 120100x60x2,0 5,00 96100x60x3,0 7,43 96100x60x4,0 9,80 90100x60x5,0 12,13 90100x70x2,0 5,36 90100x70x3,0 7,95 90100x70x4,0 10,47 90100x70x5,0 12,92 90120x40x2,0 5,04 90120x40x3,0 7,46 90120x40x4,0 9,82 90120x80x3,0 9,34 54120x80x4,0 12,35 54120x80x5,0 15,31 54

Dimensions Weight Std bundle

a x b x t kg/m m

HF-

wel

ded

HF-

wel

ded

TIG

or

Pla

sma-

wel

ded

TIG

or

Pla

sma-

wel

ded

27

21,3 1,60 0,79 52821,3 2,00 0,97 52821,3 2,60 1,22 52826,9 1,60 1,01 52826,9 2,00 1,25 52826,9 2,60 1,58 52833,7 1,60 1,28 36633,7 2,00 1,59 36633,7 2,60 2,02 36642,4 1,50 1,53 36642,4 1,60 1,63 36642,4 2,00 2,02 36642,4 2,60 2,59 36644,5 1,20 1,30 36644,5 1,50 1,62 36644,5 1,60 1,73 36644,5 2,00 2,13 36648,3 1,50 1,76 36648,3 1,60 1,87 36648,3 2,00 2,32 36648,3 2,60 2,97 36650,8 1,20 1,49 22250,8 1,50 1,85 22250,8 1,60 1,97 22250,8 2,00 2,44 22260,3 1,20 1,77 22260,3 1,50 2,21 22260,3 1,60 2,35 22260,3 2,00 2,92 22260,3 2,60 3,75 22263,5 1,20 1,87 22263,5 1,50 2,33 222

OD Wall Weight Std bundle

mm mm kg/m m

25 1,00 0,60 52825 1,25 0,74 52825 1,50 0,88 52825 2,00 1,15 52832 1,00 0,77 54632 1,25 0,96 54632 1,50 1,15 54632 2,00 1,50 54632 2,50 1,85 54633 1,50 1,18 36635 1,20 1,01 36635 1,50 1,26 36635 2,00 1,65 36638 1,00 0,91 36638 1,20 1,10 36638 1,25 1,14 36638 1,50 1,37 36638 1,60 1,46 36638 2,00 1,80 36640 1,00 0,97 36640 1,50 1,45 36640 2,00 1,90 36640 2,50 2,35 36650 1,00 1,21 22250 1,50 1,82 22250 2,00 2,40 22251 1,00 1,24 22251 1,20 1,49 22251 1,25 1,55 22251 1,50 1,86 22251 1,60 1,99 22251 2,60 3,16 22254 1,20 1,58 22254 1,50 1,97 22254 2,00 2,60 22260 1,50 2,20 22260 2,0 2,90 222

OD Wall Weight Std bundle

mm mm kg/m m

Austenitics

EN 1.4301/304,EN 1.4307/304L,EN 1.4404/316L

Ferritics

EN 1.4510

Tolerances

- length +5 -0 mm- wall thickness T3 ± 10% or

min 0,2 mm- diam. D3 ± 0,75%- straightness max 1,5

mm / m

Outside finishes

- as welded- descaled- brushed- polished- Grit 240, 320 and 400- mirror

HF - Welded Round Tubes

OT-No.: 101HF - Welded Round Tubes

OT-No.: 111HF - Welded Round Tubes

Butt Weld Fittings

28

Butt Weld Fittings

Butt Weld Fittings are manufactured from either tubes, sheet or strip depending on product and dimension.

Our Scandinavian mills in Molkom, Örnsköldsvik and Veteli are approved suppliers to the European Pressure Equipment

Directive PED 97/23/EC and certified to AD 2000 Merkblatt W0.

Our North American mill in Brockville is approved to ISO 9001:2000 and manufactures a complete range of Stainless Steel

Butt Weld Fittings according to applicable specifications of CRN (Canadian Registration Number) CSA B51 Clause 4.3,

ASME (Ameican Society of Mechanical Engineers) SA403, ASTM (American Society for Testing and Materials) A403, A815,

ANSI (American National Standards Institute) B16.9, B16.25 and MSS (Manufacturers Standardization Society) MSS SP43.

For general use our fittings are delivered with welding factor z = 0.7 without special inspection according to EN 10253-3. For

the use in pressure equipment that require welding factor z = 1.0 we manufacture fittings with special inspection according to

EN 10253-4. An extensive stock programme together with Outokumpu distribution net secures a high availability and fast

delivery service for any application.

Our stock standard is based on EN 1.4307 and 1.4432 unless other information is given. Other grades may be manufactured

on request. If you can’t find what you need in our product range please don’t hesitate to contact our sales department. We can

offer special products as well.

Diameter Wall thickness Permissible deviation

(D) (T) Minus Plus

D ≤610 All -12,5% +15%

D >610 ≤10 mm -0,35 mm + 15%

>10 mm - 0,50 mm + 15%

D F-G-H-L B C K

≤114,3 +/- 2 +/-7 +/-7 +/-4

114,3 ≤D ≤219,1 +/- 2 +/-7 +/-7 +/-7

219,1 ≤D ≤406,4 +/- 5 +/-7 +/-10 +/-7

406,4 ≤D ≤762 +/- 10 +/-10 +/-10 +/-7

762 ≤D ≤1219 +/- 15 +/-10 +/-10 +/-10

Dimension Flange

type

Size Tolerance

mm

Outside diameter of neck A 35,37 ≤DN 150>DN 150

+/-0,75% min +/- 0,3 mm+/-1% min +/- 3,0 mm

Wall thickness Sp 35,37 ≤DN 600>DN 600

-12,5% / +15%-0,5 / +15%

Outside diameter D All ≤DN 150>DN150 ≤DN 500>DN500 ≤DN1200>DN1200 >DN 600

+/-2,0 mm+/-3,0 mm+/-5,0 mm+/-7,0 mm

Length through hub H4, H5 35,37 ≤DN 80>DN80 ≤DN 250

>DN250

+/-1,5+/-2,0+/-3,0

Collar thickness F 35

37

≤18 mm>18 mm ≤50 mm≤5 mm thickness

+/-1,0 mm+/-1,5 mm+/-0,2 mm

Facing diameter d1 All ≤DN 250>DN 250

+2,0 / -1,0+3,0 / -1,0

Tolerances on wall thickness T, according to EN 10253

Tolerances on structural dimensions in mm

Tolerances according to EN 1092-1

Butt Weld Fittings

29

ElbowsPAGE 30

Elbows long radiusPAGE 30

TeesPAGE 35

Tees fabricatedPAGE 36

Reducers CCPAGE 45

Reducers ECPAGE 45

Pressed collarsPAGE 52

Angle collarsPAGE 60

CapsPAGE 61

ClampsPAGE 63

Weldring necksPAGE 55

Weld-on plate collarsPAGE 59

Butt Weld Fittings

OT-No.: 200ISOElbows 3D = R ̃ 1,5D

15 17.20 28.00 0.02 0.03

10 17,2 28,0 0,02/222* 0,03/286*

15 21,3 27,5 0,03/164* 0,04/210* 0,05/284*

20 26,9 28,5 0,04/117* 0,06/149* 0,07/201*

25 33,7 38,0 0,08/95* 0,10/120* 0,12/160*

32 42,4 47,5 0,12/74* 0,15/94* 0,19/124*

40 48,3 57,0 0,16/66* 0,21/83* 0,26/110*

50 60,3 76,0 0,27/54* 0,35/68* 0,44/89* 0,52/100*

65 76,1 95,0 0,55/36 0,73/47 0,81/52

80 88,9 114,0 0,78/31 0,90/35 0,98/39 1,01/40 1,13/45 1,17/47 1,24/50 1,89/80

100 101,6 152,0 1,20/28

114,3 152,0 1,30/24 1,75/30 1,94/32 2,00/35 3,29/39

125 139,7 190,0 2,10/20 2,70/25 3,08/26 3,10/29 4,08/40

150 168,3 229,0 3,00/16 3,90/20 4,30/21 4,50/24 5,90/33 7,40/42 8,80/50 14,0

200 219,1 305,0 5,20/13 6,80/16 7,50/17 7,80/18 10,3/26 12,8/32 17,0

250 273,0 381,0 8,00/10 12,1/15 16,1/20 20,1/26 24,0/31 25,0

300 323,9 457,0 11,60/8 17,3/12 23,0/17 28,7/22 34,3/26 23,0

350 355,6 533,0 22,2/11 29,5/16 36,8/20 44,1/24 10,0

400 406,4 610,0 29,3/10 38,6/14 48,2/17 57,6/21 20,0

450 457 686,0 36,8/9 48,9/12 61,0/5 13,0

500 508 762,0 45,4/8 60,4/11 75,4/14 90,3/17 25,0

600 610 914,0 65,4/7 87,1/9 109/12 130/14 25,0

700 711 1067,0 119/8 148/10 178/13 13,0

800 813 1219,0 156/7 195/9 232/11 20,0

900 914 1372,0 206/6 246/8 294/10 22,0

1000 1016 1524,0 243/6 304/7 365/9 22,0

1100 1118 1667,0 368/5 441/6 25,0

1200 1219 1800,0 438/6 526/7 19,0

OT-No.: 201ISOElbows 5D = R ̃ 2,5D

80 88,9 205 1,40/37 2,12/56 13

100 114,3 270 2,40/28 3,50/43 14

125 139,7 330 3,60/23 4,68/30 5,20/35 7,00/47 15

150 168,3 390 6,63/25 7,60/29 9,80/39 15

200 219,1 510 8,76/14 13,0/22 17,1/30 20

250 273,0 650 20,8/18 27,3/24 34,4/30 30

300 323,9 775 29,4/15 38,7/20 49,6/25 24

350 355,6 850 36,0/13 47,0/18 59,0/23 16

400 406,4 970 46,0/12 61,0/16 76,0/20 22

500 508 1245 98,0/12 122/16 22

600 610 1524 182/13 218/16 290/21 22

700 711 1778 297/15 395/20 20

30

Wall Thickness T mm

1,6 2,0 2,3 2,5 2,6 2,9 3,0 3,2 4,0 5,0 6,0 Max

DN D R=F Weight kg/pce / Design pressure bar T mm

Wall Thickness T mm

2,0 2,6 2,9 3,0 3,2 4,0 5,0 6,0 8,0 Max


Stock standard: EN 1.4307 and 1.4432*) Are calculated according to EN10253-4 Type A.The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4 Type A.

The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4 Type A.

Stock standard: EN 1.4307 and 1.4432

Butt Weld Fittings

31

80 84/86 240 1,9/39 2,4/57100 104/106 300 2,4/31 3,7/46130 130/131 375 4,7/31 5,7/37150 155/156 450 6,7/26 8,2/31200 206/208 600 14,5/23 19,5/31250 256/258/260 750 22,5/19 30,5/26 37,8/31300 306/308/310 900 32,5/16 43,2/21 54,0/26350 356/358/360 1050 44,0/13 58,7/18 73,5/22400 406/408/410 1200 58,0/12 77,0/16 97,0/19450 456/458/460 1350 72,0/10 97,0/14 122/17500 506/508/510 1500 90,0/9 119/12 152/15600 606/608/610 1800 128/8 169/10 215/13700 710/712/716 2100 292/12 351/14 470/19800 810/812/816 2400 304/16 381/12 458/17900 910/912/916 2700 482/9 579/11 774/15

Wall Thickness T mm

2,0 2,5 3,0 4,0 5,0 6,0 8,0

DN=ID D R=F Weight kg/pce / Design pressure bar


Elbows 3xID

15 17,2 50 25 0,08/162 0,11/24421,3 50 25 0,16/214

20 26,9 50 25 0,20/15925 33,7 60 25 0,35/15532 42,4 85 30 0,60/12340 44,5 85 30 0,41/70 0,61/104

48,3 95 30 0,76/10650 57,0 110 40 1,00/80

60,3 120 40 1,33/9565 70,0 130 40 1,38/64

76,1 145 45 1,70/59 2,07/7480 88,9 170 50 3,14/70100 101,6 195 55 3,70/55

108,0 205 55 4,45/57

Wall Thickness T mm

1,6 2,0 2,3 2,6 2,9 3,2 3,6 4,0

DN D R L Weight kg/pce / Design pressure bar

OT-No.: 205ISOElbows 4S





Butt Weld Fittings

32

15* 18,0 30 0,02/ 19820,0 23 0,04/ 217

20* 23,0 35 0,04/ 14825,0 33 0,05/ 177

25* 28,0 32,5 0,04/ 10930,0 38 0,08/ 143

32* 35,0 45 0,08/ 90 0,11/ 12238,0 50 0,11/ 83 0,15/ 112

40* 43,0 47,5 0,15/ 6644,5** 60 0,19/ 96

50* 53,0 73 0,16/ 6054,0 73 0,21/ 7857** 78 0,53/ 74

65* 69,0 95 0,47/ 6180 79,0 113 0,80/ 37

84,0/ 86,0 123 0,90/ 35 1,40/ 52100 104/ 106 150 1,20/ 28 1,80/ 42125 129/ 131 188 2,00/ 23 3,00/ 34150 154/ 156 225 2,60/ 19 3,90/ 28200 204/ 205/ 206 300 4,80/ 14 6,00/ 18 7,30/ 21 9250 254/ 255/ 256 375 7,40/ 11 9,20/ 14 11,0/ 17 6300 304/ 306/ 308 450 10,7/ 9 16,5/ 14 22,0/ 19 7350 356/ 358/ 360 525 22,5/ 12 30,0/ 16 37,0/ 20 9400 406/ 408/ 410 600 29,0/ 10 38,0/ 14 48,0/ 18 11450 456/ 458/ 460 675 37,0/ 9 49,0/ 12 61,0/ 16 13500 506/ 508/ 510 750 45,0/ 8 60,0/ 11 75,0/ 14 25600 606/ 608/ 610 900 66,0/ 48 88,0/ 9 110/ 12 25700 708/ 710/ 712 1050 117/ 8 147/ 11 177/ 13 13800 8085/ 810/ 812 1200 152/ 7 190/ 9 228/ 11 11900 910/ 912 1350 238/ 8 286/ 10 221000 1010/ 1012 1500 298/ 7 357/ 9 221100 1110/ 1112/ 1116 1650 360/ 7 432/ 8 577/ 11 25

Wall Thickness T mm

1,5 2,0 2,5 3,0 4,0 5,0 6,0 8,0 Max


OT-No.: 212Metric Tru-Bore® Elbows 3 ID (3S)

*) Are calculated according to EN10253-4 Type A.The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4 Type A.**) ISO-dimension OT-No: 200.


Butt Weld Fittings

33

40 44,5 140 0,4/75

50 54 150 0,5/61

65 69 165 0,9/46

80 84 180 1,2/37

100 104/106 200 1,6/29 2,4/44

125 129/131 225 2,4/23 3,5/35 6

150 154/156/158 250 3,1/19 4,6/29 6,1/38

160/162 7,6/46 9,12/55 6

200 204/205/206 300 4,8/14 6,0/18 7,3/21

208/210 9,7/27 12,5/34 9

250 254/255/256 350 7,0/11 8,7/14 10,5/16

258/260 14,0/22 17,5/27 10

300 304/305 400 9,6/9 12,0/11

306/308/310 14,4/13 19,2/18 23,9/23 10

350 355/356/358 450 16,0/9 19,0/11 25,0/15 10

360/362 32,0/19 38,0/23 10

400 406/408 500 24,0/10 32,0/13 11

410/412 40,0/16 48,0/20 12

450 456/458 550 30,0/9 40,0/12

460/462 49,0/14 59,0/17

500 506/508 600 37,0/8 48,0/10

510/512 60,0/13 72,0/15

600 606/608 700 49,0/6 66,0/8

610/612 82,0/11 101,0/14 10

700 708/710/712 800 89,0/7 112/9 135/12 8

800 808/810/812 900 115/6 143/8 172/10

900 908/910/912 1000 143/6 179/7 215/9 10

1000 1010/1012 1100 273/6 327/8

Wall thickness T mm

2,0 2.5 3,0 4,0 5,0 6,0 Max



Elbows ID+100

10 12,0 30 20 0,03/14115,0 50 25 0,07/178

15 20,0 50 25 0,11/24420 23,0 50 25 0,10/106

25,0 50 25 0,15/13125 28,0 55 25 0,14/35

30,0 55 35 0,19/10632 35,0 65 25 0,19/66

38,0 70 25 0,36/10950 51,0 95 35 0,81/80

Wall Thickness T mm

1,0 1,5 2,0 2,6

DN=ID D R L Weight kg/pce / Design pressure bar


Elbows 4S





Butt Weld Fittings

34

OT-No.: 226ANSIElbows ASTM A 403 WPW / WPWX / WPS LR

15** 1/2” 21,3 38 38 2,11 0,06 2,77 0,0820** 3/4” 26,7 38 38 2,11 0,06 2,87 0,0925* 1” 33,4 38 38 2,77 0,13 3,38 0,1632* 1 1/4” 42,2 48 48 2,77 0,21 3,56 0,2540* 1 1/2” 48,3 57 57 2,77 0,29 3,68 0,4050* 2” 60,3 76 76 2,77 0,49 3,91 0,7165* 2 1/2” 73,0 95 95 2,11 0,55 3,05 0,80 5,16 1,4080* 3” 88,9 114 114 2,11 0,80 3,05 1,20 5,49 2,18100* 3 1/2” 101,6 133 133 2,11 1,19 3,05 1,70 5,74 2,83

4” 114,3 152 152 2,11 1,33 3,05 2,10 6,02 4,17125 5” 141,3 190 190 2,77 2,95 5,16 3,63 6,55 6,86150* 6” 168,3 229 229 2,77 4,05 3,40 5,20 7,11 10,9200* 8” 219,1 305 305 2,77 7,00 3,76 10,1 8,18 21,5250* 10” 273,0 381 381 3,40 13,2 4,19 17,5 9,27 38,6300* 12” 323,9 457 457 3,96 23,5 4,57 27,0 9,53 59,4350 14” 355,6 533 533 3,96 30,0 4,78 36,3 9,53 70,3400 16” 406,4 610 610 4,19 40,8 4,78 47,5 9,53 91,6450 18” 457 686 686 4,19 51,8 4,78 58,6 9,53 122500 20” 598 762 762 4,78 72,0 5,54 84,0 9,53 150600 24” 610 914 914 5,54 127 6,35 141 9,53 211

DN NPS D R H Sch 5S Sch 10S Sch 40S*** STD

mm mm mm wt mm kg/pce wt mm kg/pce wt mm kg/pce wt mm kg/pce

Stock standard: 304/304L and 316/316LDN 150-600 in Sch 10S 304/304L, 316/316L

Note! 304/304L is not stock standard for DN15-65 *) Sch 10S EN1.4462 (2205), EN1.4547 (254 SMO)

**) Sch 10S EN1.4547 (254 SMO)***) DN 15-100 only in 316

Reference to ASTM A 403/A 403M-06, ASTM A 815.Table 1 Fitting Classes for WP Grades:Class Construction NDT

S Seamless NoneW Welded Radiography or UltrasonicWX Welded Radiography

Butt Weld Fittings

35

10 17,2 25,0 50 14,0 0,04/6215 21,3 27,5 55 14,5 0,07/6420 26,9 28,5 57 12,5 0,09/5525 33,7 38,0 76 16,0 0,15/4032 42,4 47,5 95 21,5 0,24/3740 48,3 57,0 114 26,0 0,34/2950 60,3 64,0 128 27,0 0,50/1965* 76,1 76,0 152 27,0 0,70/2180* 88,9 86,0 172 30,0 0,90/17100* 114,3 105 210 35,0 1,40/12 1,70/18 2,10/27125* 139,7 124 248 40,0 2,30/10 3,00/14150* 168,3 143 286 32,0 4,10/8 4,80/12200* 219,1 178 356 50,0 6,60/7 7,60/8250 273,0 216 432 60,0 10,0/5 14,0/9 13300 323,9 254 508 70,0 15,0/4 19,0/6 13350 355,6 279 558 72,0 18,0/3 23,0/5 13400 406,4 305 610 90,0 28,0/2 28,0/4 13450 457 343 686 100 36,0/3 45,0/5 19500 508 381 762 105 44,0/3 55,0/4 19600 610 432 864 110 72,0/3 19

Wall Thickness T mm

1,6 2,0 2,6 3,0 4,0 5,0 Max

DN D F 2F R Weight kg/pce / Design pressure bar T mm

OT-No.: 300ISO Tees equal pressed

Stock standard: EN 1.4307 and 1.4432The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4 Type A.*) The pressures are calculated for grade EN 1. 4307 at 20°C according to EN 10253-4 Type A.

Butt Weld Fittings

36

100 114,3 76,1 3 95 105 1,90/23

88,9 3 98 105 2,00/21125 139,7 88,9 3 111 124 2,80/18

114,3 3 117 124 2,90/15150 168,3 114,3 3 130 148 3,90/14

139,7 3 137 148 4,00/12200 219,1 139,7 3 162 178 6,20/10

168,3 3 168 178 6,40/9250 273,0 168,3 3 194 216 9,30/7

219,1 3 203 216 9,70/6300 323,9 219,1 3 229 254 13,1/6

273,0 3 241 254 13,6/6350 355,6 273,0 3 257 279 16,1/4

323,9 3 270 279 16,8/4400 406,4 323,9 3 295 305 20,3/4

355,6 3 305 305 20,8/3450 457 406,4 3 330 343 26,0/3

355,6 3 330 343 25,6/3500 508 406,4 3 356 381 31,4/3

457 3 368 381 32,3/2600 610 457 3 419 432 42,4/2

508 3 432 432 43,3/2

Weight / pressure

DN D D1 T=T1 F L kg/pce / bar

OT-No.: 301ISOTees reducing fabricated (ISO 5251)


Fabricated on request

37

Butt Weld Fittings

50 60,3 33,7 50 2 0,2942,4 0,2848,3 3 0,2860,3 0,27

65 76,1 42,4 65 2 0,47 0,5948,3 3 0,47 0,5960,3 0,46 0,5876,1 4 0,45 0,56

80 88,9 48,3 80 3 0,68 0,8560,3 0,68 0,8476,1 4 0,67 0,8388,9 5 0,65 0,81

100 114,3 60,3 100 3 1,10 1,37 1,6476,1 4 1,09 1,36 1,6388,9 5 1,08 1,35 1,61114,3 7 1,05 1,31 1,57

125 139,7 76,1 125 4 1,69 2,10 2,5288,9 5 1,68 2,09 2,50114,3 7 1,66 2,07 2,47139,7 8 1,61 2,01 2,41

150 168,3 88,9 150 5 2,45 3,05 3,65114,3 7 2,43 3,03 3,62139,7 8 2,39 2,99 3,58168,3 10 2,33 2,91 3,49

200 219,1 114,3 200 7 5,32 6,38 8,47 10,5139,7 8 5,28 6,32 8,40 10,5168,3 10 5,23 6,27 8,33 10,4219,1 12 5,05 6,06 8,07 10,1

250 273,0 139,7 250 8 9,96 13,2 16,5168,3 10 9,89 13,2 16,4219,1 12 9,74 13,0 16,1273,0 13 9,41 12,5 15,6

300 323,9 168,3 300 10 14,2 18,9 23,5 28,2219,1 12 14,0 18,7 23,3 27,9273,0 13 13,8 18,4 22,9 27,4323,9 15 13,4 17,9 22,3 26,7

350 355,6 219,1 350 12 18,2 24,2 30,1273,0 13 17,9 23,8 29,6323,9 15 17,6 23,4 29,2355,6 17 17,3 23,0 28,7

400 406,4 273,0 400 13 25,3 31,2323,9 13 23,2 30,9355,6 15 23,1 30,7406,4 20 22,6 30,1

Wall thickness mm

2,0 2,5 3,0 4,0 5,0 6,0

DN D D1 F h Weight kg/pce / Design pressure bar*

OT-No.: 302ISOTees reducing and equal drawn

Stock standard: EN 1.4432*) Pressure ratings can be done if tube dimension connected to the branch is known.

Butt Weld Fittings

38

50 60,3 33,7 125 0,87/34 1,04/46 1,28/5742,4 0,91/30 1,08/40 1,34/5148,3 0,93/28 1,10/37 1,38/4760,3 0,98/24 1,21/32 1,45/41

65 76,1 42,4 140 1,23/26 1,48/34 1,72/4348,3 1,26/24 1,50/32 1,86/4060,3 1,31/21 1,55/28 1,94/3576,1 1,37/18 1,70/24 2,03/30

80 88,9 48,3 150 1,53/21 1,84/28 2,15/3660,3 1,58/19 1,89/25 2,35/3276,1 1,65/16 1,95/22 2,45/2788,9 1,70/15 2,06/20 2,53/25

100 114,3 60,3 160 2,07/16 2,50/21 3,07/26 3,91/38 4,74/5176,1 2,13/14 2,56/18 3,17/23 4,19/33 5,00/4588,9 2,18/12 2,60/17 3,25/21 4,29/31 5,09/41114,3 2,27/10 2,83/14 3,83/18 4,47/26 5,55/35

125 139,7 76,1 180 2,84/12 3,43/16 4,23/20 5,39/29 6,54/3988,9 2,89/11 3,48/14 4,31/18 5,70/27 6,84/35114,3 3,00/9 3,56/12 4,46/15 5,91/23 7,01/31139,7 3,07/8 3,83/11 4,59/14 6,08/20 7,56/27

150 168,3 88,9 200 3,76/9 4,56/15 5,61/16 7,18/23 8,73/31 10,4/39114,3 3,87/8 4,65/13 5,77/14 7,65/20 9,17/27 10,7/34139,7 3,97/7 4,95/11 5,92/12 7,86/18 9,32/24 11,2/30168,3 4,05/6 5,05/10 6,05/11 8,03/16 9,99/21 11,9/27

200 219,1 114,3 250 7,4/9 9,1/11 11,7/17 14,2/22 17,2/28139,7 7,8/8 9,3/10 12,4/15 14,9/20 17,4/25168,3 7,9/7 9,5/9 12,6/13 15,1/18 18,1/22219,1 8,2/6 9,8/7 13,0/11 16,2/15 19,4/19

250 273,0 139,7 300 11,3/7 13,6/8 17,5/13 21,3/33 25,7/21168,3 11,5/6 13,8/7 18,4/11 22,2/30 25,9/19219,1 11,9/5 14,2/6 18,9/9 22,6/25 27,2/16273,0 12,1/4 14,5/5 19,3/8 24,0/22 28,8/14

300 323,9 168,3 330 14,3/5 17,6/7 22,7/10 27,7/9 33,4/17219,1 14,5/4 18,0/6 24,0/8 28,8/11 33,0/14273,0 14,7/4 18,4/5 24,5/7 30,5/10 35,2/13323,9 15,5/3 18,5/4 26,7/6 30,8/9 36,9/11

350 355,6 219,1 360 21,4/5 27,4/8 34,4/10 40,3/14273,0 21,8/4 29,0/7 34,8/9 41,9/12323,9 22,2/4 29,5/6 36,8/8 44,0/11355,6 22,2/4 29,5/6 36,9/8 44,2/10

400 406,4 273,0 400 27,3/4 34,8/6 43,7/8 51,2/11323,9 27,7/3 36,8/5 44,0/8 53,1/10355,6 27,9/3 37,1/5 46,3/7 55,4/9406,4 27,9/3 37,2/5 46,5/6 55,7/8

Wall Thickness T=T1 mm

2,0 2,5 3,0 4,0 5,0 6,0

DN D D1 F Weight kg/pce / Design pressure bar

OT-No.: 303ISO Tees reducing and equal fabricated (SFS 4164)



Butt Weld Fittings

39

450 457 323,9 450 34,7/3 46,1/5 57,6/7355,6 35,0/3 46,5/5 58,1/6406,4 35,4/3 47,1/4 58,7/6457 35,4/3 47,1/4 58,8/5

500 508 355,6 500 42,8/3 56,9/4 68,6/6406,4 43,5/3 57,6/4 71,9/5457 43,7/2 58,2/4 72,6/5508 43,6/2 58,2/3 72,7/5

600 610 406,4 600 81,8/3 98,7/6 119/6457 82,6/3 103/6 124/6508 83,4/3 104/5 125/5610 83,8/3 105/5 126/5

700 711 457 700 111/3 134/4 162/8508 112/3 135/4 163/8610 113/2 136/3 170/7711 114/2 134/3 171/6

800 813 508 800 145/2 175/3 206/4 272/7610 147/2 177/3 213/4 293/6711 149/2 186/3 223/3 297/5813 149/2 186/2 223/3 298/5

900 914 610 900 184/2 230/3 276/4 367/5711 187/2 233/2 280/3 372/5813 189/1 236/2 283/3 377/4914 188/1 236/2 283/3 377/4

1000 1016 711 1000 229/2 286/2 342/3 456/4813 231/1 289/2 346/3 461/4914 234/1 292/2 350/2 466/41016 233/1 291/2 349/2 465/3

Wall Thickness T=T1 mm

3,0 4,0 5,0 6,0 8,0

DN D D1 F Weight kg/pce / Design pressure bar

OT-No.: 303ISOTees reducing and equal fabricated (SFS 4164)



Butt Weld Fittings

40

15 20 23 46 10,5 0,06/7720 25 33 66 15,5 0,11/5425 30 38 76 18,0 0,14/4332 38 50 100 24,0 0,30/4140 44,5* 60 120 28,0 0,35/2550 54 73 146 30,0 0,51/2050 57* 76 152 23,0 0,85/2465 69 80 160 27,5 0,70/1665 76 80 160 30,5 1,10/2365 79 80 160 32,0 0,75/1480 84 80 160 30,0 0,80/13100 104 90 180 25,0 1,30/11

105 1,80/15125 129 115 230 40,0 2,10/8

130 2,80/10150 154 135 270 40,0 3,10/6

155 4,00/5200 205 175 350 57,0 6,10/5

206 8,20/7250 256 216 432 75,0 10,0/5 8

258 13,0/8300 306 254 508 80,0 13,0/4 13

308 19,0/6356 356 279 558 72,0 18,0/3 20

358 23,0/5400 406 305 610 90,0 28,0/7 19

408 28,0/4410 36,0/8

450 456 343 686 100 36,0/2 19458 36,0/4460 45,0/5

500 506 381 762 105 44,0/2 19508 44,0/3510 55,0/4

600 606 432 864 110 72,0/2 19508 72,0/2610 72,0/3

Wall Thickness T mm

2,0 2,5 3,0 4,0 5,0 Max

DN D F 2F R Weight kg/pce / Design pressure bar T m

OT-No.: 310Metric Tru-Bore® Tees equal pressed

Stock standard: EN 1.4307 and 1.4432*) ISO-dimensions OT-No:300.The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4, Type A.

Butt Weld Fittings

41

100 104 54 2,0 50 75 0,60/1884 80 90 1,00/14

125 129 84 80 102 1,20/12104 100 112 1,50/10

150 154 84 80 115 1,40/9104 100 125 1,80/6

200 204 104 100 150 2,30/7129 125 162 2,00/7154 150 175 3,60/6

206 106 3,0 100 150 3,40/8131 125 162 4,40/7156 150 175 5,40/7

250 254 104 2,0 100 175 2,80/5154 150 200 4,40/5204 200 225 6,10/3

256 106 3,0 100 175 4,20/11156 150 200 6,60/9206 200 225 9,10/7

300 304 154 2,0 150 225 5,10/4204 200 250 7,10/3254 250 275 9,10/3

306 156 3,0 150 225 7,70/8206 200 250 10,6/6256 250 275 13,7/5

350 356 206 200 275 12,1/6256 250 300 15,6/5306 300 325 19,3/4

358 208 4,0 200 275 16,2/8258 250 300 20,9/7308 300 325 25,8/6

400 406 256 3,0 250 325 17,5/4306 300 350 21,6/4356 350 375 25,8/3

408 308 4,0 300 350 28,8/6258 250 325 23,4/7358 350 375 34,5/5

500 506 306 3,0 300 400 24,7/3356 350 425 30,6/3406 400 450 47,7/3

508 308 4,0 300 400 34,8/5358 350 425 41,5/4408 400 450 48,5/4

600 606 506 3,0 500 550 53,8/2608 508 4,0 500 550 73,2/3610 510 5,0 500 550 91,5/4

Weight

DN D D1 T=T1 L H kg/pce / Design pressure bar


Tees reducing fabricated

Stock standard: EN 1.4307 and 1.4432The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4, Type A.

Butt Weld Fittings

42

50 50 25 50 2 0,2632 0,2540 3 0,2550 0,25

65 65 32 65 2 0,43 0,5440 3 0,43 0,5450 0,42 0,5365 4 0,41 0,52

80 80 40 80 3 0,65 0,8150 0,64 0,8165 4 0,63 0,8080 5 0,62 0,78

100 100 50 100 3 1,00 1,26 1,5265 4 1,00 1,25 1,5180 5 0,99 1,24 1,49100 7 0,97 1,22 1,47

125 125 65 125 4 1,56 1,96 2,3680 5 1,55 1,95 2,35100 7 1,54 1,93 2,33125 8 1,50 1,88 2,27

150 150 80 150 5 2,24 2,81 3,38100 7 2,23 2,79 3,36125 8 2,20 2,76 3,32150 10 2,15 2,70 3,26

200 200 100 200 7 4,99 6,00 8,04 10,1125 8 4,95 5,96 7,98 10,0150 10 4,92 5,91 7,93 10.0200 12 4,76 5,73 7,69 9,68

250 250 125 250 8 9,35 12,5 15,7150 10 9,30 12,5 15,6200 12 9,16 12,3 15,4250 13 8,88 11,9 15,0

300 300 150 300 10 13,4 18,0 22,5 27,1200 12 13,3 17,8 22,3 26,8250 13 13,1 17,5 22,0 26,5300 15 12,7 17,1 21,4 25,8

350 350 200 350 12 18,2 24,3 30,5250 13 18,0 24,0 30,1300 15 17,8 23,7 29,8350 17 17,3 23,1 29,0

400 400 250 400 13 23,6 31,5300 15 23,4 31,2350 17 23,1 30,9

Wall thickness mm

2,0 2,5 3,0 4,0 5,0 6,0

DN d d1 F h Weight kg/pce / Design pressure bar*


Tees equal and reduced drawn

Stock standard: EN 1.4432*) Pressure ratings can be done if tube dimension connected to the branch is known.

43

Butt Weld Fittings

Schedule

10S 40S/STD

DN NPS D mm L H R Wall Thickness T mm / Weight kg/pce

OT-No.: 320ANSITees ASTM A 403 WPW / WPWX / WPS

15 1/2 21,3 50 25 12,0 2,11 0,08 2,77 0,1120 3/4 26,7 58 29 14,0 2,11 0,11 2,87 0,2025 1 33,4 76 38 17,0 2,77 0,30 3,38 0,3032 1 1/4 42,2 96 48 16,0 2,77 0,05 3,56 0,6340 1 1/2 48,3 114 57 20,0 2,77 0,70 3,68 0,9050 2 60,3 128 64 25,0 2,77 0,80 3,91 1,2065 2 1/2 73,0 152 76 20,0 3,05 1,36 5,16 2,3080 3 88,9 172 86 28,0 3,05 1,80 5,49 3,20100 4 114,3 210 105 30,0 3,05 2,62 6,02 5,10125 5 141,3 248 124 38,0 3,40 4,60 6,55 9,40150 6 168,3 286 143 45,0 3,40 6,30 7,11 16,1200 8 219,1 356 178 50,0 3,76 11,4 8,18 31,0250 10 273,0 432 216 60,0 4,19 27,1 9,27 53,1300 12 323,9 508 254 70,0 4,57 38,0 9,53 77,0350 14 355,6 558 279 72,0 4,78 46,0 9,53 93,0400 16 406,4 610 305 90,0 4,78 57,0 9,53 116450 18 457 686 343 100 4,78 73,0 9,53 147500 20 508 762 381 105 5,54 111 9,53 182600 24 610 864 432 110 6,35 149 9,53 254

Stock standard: Sch 10S size DN 15 -DN100 and DN 150 in grade 316, EN 1,4462 (2205) and DN25 - DN100 EN 1,4547 (254 SMO).

Reference to ASTM A 403/A 403M-06, ASTM A 815.Table 1 Fitting Classes for WP Grades:Class Construction NDT

S Seamless NoneW Welded Radiography or UltrasonicWX Welded Radiography

Butt Weld Fittings

44

Butt Weld Fittings

45

20 26,9 21,3 38 0,10/13925 33,7 51 0,10/109

26,9 0,10/10932 42,4 33,7 0,10/8640 48,3 64 0,10/75

42,4 0,10/7550 60,3 33,7 76 0,20/59

48,3 0,20/5965 76,1 48,3 90 0,30/46

60,3 0,30/4780 88,9 0,30/39

76,1 0,30/40100 114,3 102 0,50/30

88,9 0,50/31125 139,7 127 1,10/25

114,3 1,10/25150 168,3 88,9 140 1,00/20

114,3 1,00/21139,7 1,10/21

200 219,1 152 1,30/152,00/23

168,3 1,50/152,20/23

250 273,0 178 2,00/123,00/18

219,1 2,20/133,30/19

300 323,9 168,3 203 3,70/16219,1 4,20/16273,0 4,60/16

350 355,6 219,1 330 7,00/15273,0 7,70/15323,3 8,40/15

400 406,4 273,0 356 9,00/13323,9 9,70/13355,6 10,2/13

450 457 323,9 381 11,2/11355,6 11,5/11406,4 12,4/11

500 508 355,6 508 16,4/11406,4 17,4/11457 18,3/11

600 610 406,4 25,7/10457 27,0/10508 28,3/10

Wall Thickness mm

2,0 3,0 4,0

DN D D1 L Weight kg/pce / Design pressure bar for CC*

EC OT-No.: 430CC OT-No.: 431ISO Reducers type CC, EC (ISO 5251)

Stock standard: EN 1.4307 and 1.4432*) for EC reducers the pressure is appr. 10% lower.The pressures are calculated for grade EN 1.4307 at 20°C according to EN 10253-3 Type A.All dimensions can be delivered to meet EN 10253-4 Type A.

Butt Weld Fittings

46

15 21,3 13,7 23 0,02/ 17617,2 12 0,01/ 176

20 26,9 13,7 40 0,04/ 13717,2 29 0.03/ 13721,3 17 0.02/ 137

25 33,7 17,2 50 0,06/ 10821,3 37 0,05/ 10826,9 20 0.03/ 108

32 42,4 21,3 63 0,10/ 8526,9 46 0.08/ 8533,7 26 0.05/ 85

40 48,3 21,3 81 0,14/ 7426,9 63 0.11/ 7433,7 43 0,09/ 7442,4 17 0,04/ 74

50 60,3 21,3 117 0,24/ 5926,9 99 0,21/ 59 0,26/ 7433,7 79 0,18/ 59 0,22/ 7442,4 53 0,13/ 59 0,16/ 7448,3 36 0,10/ 59 0,12/ 74 0,14/ 90

65 76,1 26,9 148 0,38/ 4733,7 126 0,34/ 47 0,42/ 59 0,50/ 9042,4 100 0,29/ 47 0,36/ 59 0,43/ 9048,3 82 0,25/ 47 0,31/ 59 0,37/ 9060,3 47 0,16/ 47 0,20/ 59 0,23/ 90

80 88,9 33,7 165 0,51/ 4042,4 138 0,45/ 40 0,55/ 50 0,66/ 6048,3 120 0,41/ 40 0,50/ 50 0,60/ 6060,3 85 0,31/ 40 0,39/ 50 0,46/ 6076,1 38 0,16/ 40 0,19/ 50 0,23/ 60

100 114,3 42,4 216 0,85/ 3148,3 195 0,78/ 31 0,97/ 39 1,16/ 46 1,53/ 6260,3 160 0,69/ 31 0,86/ 39 1,03/ 46 1,35/ 6276,1 113 0,53/ 31 0,66/ 39 0,79/ 46 1,05/ 6288,9 75 0,38/ 31 0,47/ 39 0,56/ 46 0,74/ 62

125 139,7 60,3 235 1,17/ 25 1,45/ 32 1,74/ 38 2,29/ 5176,1 188 1,01/ 25 1,26/ 32 1,50/ 38 1,98/ 5188,9 151 0,86/ 25 1,07/ 32 1,28/ 38 1,69/ 51114,3 75 0,46/ 25 0,59/ 32 0,71/ 38 0,94/ 51

150 168,3 76,1 273 1,67/ 21 2,07/ 26 2,48/ 32 3,23/ 4288,9 235 1,51/ 21 1,88/ 26 2,25/ 32 2,97/ 42114,3 160 1,13/ 21 0,82/ 26 0.98/ 32 1,29/ 42139,7 85 0,66/ 21 0,82/ 26 0,98/ 32 1,29/ 42

200 219,1 88,9 385 2,97/ 16 3,70/ 20 4,43/ 24 5,86/ 32 7,28/ 40114,3 310 2,59/ 16 3,23/ 20 3,86/ 24 5,12/ 32 6,36/ 40139,7 235 2,12/ 16 2,64/ 20 3,16/ 24 4,18/ 32 5,20/ 40168,3 150 1,46/ 16 1,82/ 20 2,18/ 24 2,89/ 32 3,59/ 40

Wall thickness mm

2,0 2,5 3,0 4,0 5,0 6,0 8,0 10


EC OT-No.: 400CC OT-No.: 401ISO Reducers type CC, EC 3x(D-D1) (SFS 4162, EN 10253-3)


Butt Weld Fittings

47

250 273 114,3 470 4,57/ 13 5,70/ 16 6,82/ 19 9,05/ 25 11,3/ 32 13,4/ 39139,7 395 4,10/ 13 5,11/ 16 6,12/ 19 8,11/ 25 10,1/ 32 12,1/ 39168,3 310 3,44/ 13 4,29/ 16 5,14/ 19 6,82/ 25 8,48/ 32 10,1/ 39219,1 160 1,98/ 13 2,47/ 16 2,96/ 19 3,93/ 25 4,89/ 32 5,85/ 39

300 323,9 139,7 545 6,36/ 11 7,93/ 13 9,49/ 16 12,6/ 21 15,67/ 27 18,7/ 33168,3 461 5,71/ 11 7,13/ 13 8,53/ 16 11,3/ 21 14,1/ 27 16,9/ 33219,1 310 4,24/ 11 5,29/ 13 6,34/ 16 8,42/ 21 10,5/ 27 12,5/ 33273 151 2,27/ 11 2,84/ 13 3,40/ 16 4,51/ 21 5,62/ 27 6,72/ 33

350 355,6 168,3 554 7,31/ 10 9,12/ 12 10,9/ 15 14,5/ 19 18,1/ 15 21,6/ 29219,1 404 5,85/ 10 7,30/ 12 8,75/ 15 11,6/ 19 14,5/ 15 17,3/ 29273 244 3,87/ 10 4,83/ 12 5,78/ 15 7,69/ 19 9,58/ 15 11,5/ 29323,9 94 1,61/ 10 2,01/ 12 2,41/ 15 3,20/ 19 3,99/ 15 4,78/ 29

400 406,4 219,1 554 10,9/ 11 13,1/ 13 17,4/ 17 21,6/ 21 25,9/ 26 34,3/ 35273 395 8,45/ 11 10,1/ 13 13,5/ 17 16,8/ 21 20,1/ 26 26,6/ 35323,9 244 5,61/ 11 6,73/ 13 8,59/ 17 11,2/ 21 13,3/ 26 17,7/ 35355,6 150 3,60/ 11 4,20/ 13 5,74/ 17 7,16/ 21 8,57/ 26 11,4/ 35

450 457 273 545 15,0/ 11 20,0/15 25.0/ 19 29,8/ 23 39,5/ 31323,9 395 11,7/ 11 15,5/ 15 19,3/ 19 23,1/23 24,4/ 31355,6 301 9,30/ 11 12,3/ 15 15,3/ 19 18,4/ 23 24,4/ 31406,4 150 4,90/ 11 6,51/ 15 8,12/ 19 9,73/ 23 12,9/ 31

500 508 323,9 545 17,1/ 10 22,8/ 14 28,4/ 17 34,0/ 21 45,1/ 27355,6 451 14,7/ 10 19,6/ 14 24,4/ 17 29,2/ 21 38,1/ 27406,4 301 10,4/ 10 13,9/ 14 17,3/ 17 20,7/ 21 25,5/ 27457,2 150 5,48/ 10 7,29/ 14 9,09/ 17 10,9/ 21 14,5/ 27

600 610 355,6 752 27,5/ 9 36,5/ 11 45,6/ 14 54,6/ 17 74,5/ 23406,4 601 23,1/ 9 30,8/ 11 38,4/ 14 45,9/ 17 61,0/ 23457 451 18,2/ 9 24,2/ 11 30,2/ 14 36,2/ 17 48,1/ 23508 301 12,7/ 9 17,0/ 11 21,2/ 14 25,3/ 17 33,7/ 23

700 711 406,4 902 38,2/ 7 50,8/ 10 63,4/ 13 75,9/ 16 101/ 21 126/ 27457 752 33,3/ 7 44,3/ 10 55,3/ 13 66,2/ 16 88,0/ 21 110/ 27508 601 27,8/ 7 37,0/ 10 46,1/ 13 55,2/ 16 73,4/ 21 91,5/ 27610 301 15,1/ 7 20,1/ 10 25,0/ 13 30,0/ 16 40,0/21 50,0/ 27

800 813 457 1053 50,7/ 7 67,5/ 9 84,2/ 11 101/ 14 134/ 19 167/ 24508 902 45,2/ 7 60,1/ 9 75/ 11 90,0/ 14 120/ 19 149/ 24610 601 32,4/ 7 43,2/ 9 53,9/ 11 64,5/ 14 85,8/ 19 107/ 24711 301 17,4/ 7 23,2/ 9 28,9/ 11 34,7/ 14 46,1/ 19 57,5/ 24

900 914 508 1203 64,9/ 6 86,4/ 8 108/ 10 129/ 12 172/ 17 214/ 15610 902 52,1/ 6 69,4/ 8 86,7/ 10 104/ 12 138/ 17 172/ 15711 601 37,1/ 6 49,4/ 8 61,6/ 10 73,8/ 12 98,2/ 17 122/ 15813 301 19,7/ 6 26,3/ 8 32,8/ 10 39,3/ 12 52,3/ 17 65,2/ 15

1000 1016 610 1203 74,2/ 5 98,8/ 7 123/ 9 148/ 11 197/ 15 245/ 19711 902 59,1/ 5 78,7/ 7 98,3/ 9 118/ 11 157/ 15 195/ 19813 601 41,7/ 5 55,6/ 7 69,4/ 9 83,1/ 11 111/ 15 138/ 19914 301 22,1/ 5 29,4/ 7 36,7/ 9 44,0/ 11 58,5/ 15 73,0/ 19

1100 1118 711 1203 84,1/ 5 112/ 7 140/ 8 168/ 10 223/ 13 278/ 17813 909 66,7/ 5 88,8/ 7 111/ 8 133/ 10 177/ 13 221/ 17914 609 47,0/ 5 62,7/ 7 78,2/ 8 93,8/ 10 125/ 13 156/ 171016 308 25,0/ 5 33,3/ 7 41,6/ 8 49,8/ 10 66,3/ 13 82,7/ 17

1200 1219 813 1205 93,0/ 4 124/ 6 155/ 7 185/ 9 247/ 13 308/ 16914 905 73,3/ 4 97,7/ 6 122/ 7 146/ 9 195/ 13 243/ 161016 604 51,3/ 4 68,3/ 6 85,3/ 7 102/ 9 136/ 13 170/ 161118 296 26,3/ 4 35,0/ 6 43,8/ 7 54,3/ 9 69,8/ 13 87,2/ 16

Wall thickness mm

2,0 2,5 3,0 4,0 5,0 6,0 8,0 10


EC OT-No.: 400CC OT-No.: 401ISO Reducers type CC, EC 3x(D-D1) (SFS 4162, EN 10253-3)


Butt Weld Fittings

48

25 25 17 24 0,02/109 0,02/14820 15 0,01/109 0,02/148

25 28 20 24 0,02/9723 15 0,01/97

30 20 30 0,03/90 0,05/11425 15 0,02/90 0,03/114

32 32 20 36 0,05/11425 21 0,03/114

33 23 30 0,03/8128 15 0,02/81

38 20 54 0,06/7025 39 0,05/7028 30 0,04/7030 24 0,03/70

40 40 20 60 0,10/9025 45 0,08/9028 36 0,05/6732 24 0,05/90

43 25 54 0,09/6228 45 0,08/6233 30 0,04/62

44 30 42 0,09/8150 50 25 75 0,15/71 0,19/90 0,23/109

54 25 87 0,17/6630 72 0,16/6632 54 0,12/71 0,15/90 0,18/10934 60 0,13/6638 48 0,11/6640 42 0,09/4944 30 0,07/66 0,09/83 0,11/100

65 65 32 99 0,25/54 0,32/68 0,39/8340 75 0,21/54 0,26/68 0,32/8350 45 0,14/54 0,17/68 0,21/83

69 30 117 0,29/5138 93 0,25/5144 75 0,20/5154 45 0,13/51

70 54 48 0,15/50

Wall thickness mm

1,5 2,0 2,5 3,0 4,0 5,0 6,0


EC OT-No.: 410CC OT-No.: 411Metric Tru-Bore®

Reducers CC, EC 3x(D-D1), half angle 9,5˚


Butt Weld Fittings

49




80 79 54 75 0,30/4480 40 120 0,38/44 0,48/55 0,58/66

50 90 0,31/44 0,39/55 0,47/6665 45 0,17/44 0,21/55 0,26/66

84 44 120 0,48/4254 90 0,38/4269 45 0,17/42

100 100 50 150 0,59/35 0,74/44 0,89/53 1,20/7165 105 0,45/35 0,57/44 0,68/53 0,92/7180 60 0,28/35 0,35/44 0,42/53 0,57/71

125 125 65 180 0,89/28 1,11/35 1,34/42 1,81/5680 135 0,72/28 0,90/35 1,08/42 1,46/56100 75 0,44/28 0,55/35 0,66/42 0,89/56

150 150 80 210 1,25/23 1,57/27 1,89/35 2,54/47100 150 0,97/23 1,21/27 1,46/35 1,96/47125 75 0,53/23 0,67/27 0,80/35 1,08/47

200 200 100 300 2,31/17 2,90/22 3,49/26 4,69/35 5,90/44125 225 1,88/17 2,36/22 2,83/26 3,80/35 4,78/44150 150 1,35/17 1,69/22 2,03/26 2,73/35 3,43/44

250 250 125 375 3,61/14 4,52/17 5,44/20 7,29/28 9,16/35 11,1/42150 300 3,08/14 3,85/17 4,64/20 6,21/28 7,80/35 9,41/42200 150 1,73/14 2,17/17 2,60/20 3,49/28 4,38/35 5,28/42

300 300 150 450 5,19/11 6,50/14 7,81/17 10,5/23 13,1/29 15,8/35200 300 3,84/11 4,81/14 5,78/17 7,74/23 9,71/29 11,7/35250 150 2,11/11 2,64/14 3,18/17 4,25/23 5,33/29 6,42/35

350 350 200 450 6,33/10 7,92/12 9,53/14 12,8/20 16,0/25 19,3/30250 300 4,60/10 5,76/12 6,92/14 9,26/20 11,6/25 14,0/30300 150 2,49/10 3,12/12 3,75/14 5,01/20 6,28/25 7,56/30

400 400 250 450 9,35/10 11,2/13 15,0/17 18,8/22 22,7/26300 300 6,71/10 8,06/13 10,8/17 13,5/22 16,3/26350 150 3,59/10 4,32/13 5,77/17 7,23/22 8,70/26

Wall thickness mm

1,5 2,0 2,5 3,0 4,0 5,0 6,0


Butt Weld Fittings

50

450 450 300 450 13/11 17,3/15 21,7/19 26,1/23350 300 9,2/11 12,3/15 15,4/19 18,6/23400 150 4,9/11 6,5/15 8,2/19 9,8/23

500 500 300 600 18,4/10 24,6/14 30,8/17 37,1/21350 450 14,7/10 19,6/14 24,6/17 29,5/21400 300 10,4/10 13,8/14 17,3/17 20,8/21450 150 5,5/10 7,3/14 9,1/17 11,0/21

600 600 350 750 27,3/8 36,5/11 45,7/14 54,9/17 73,6/23400 600 23,0/8 30,7/11 38,5/14 46,2/17 61,9/23450 450 18,1/8 24,2/11 30,3/14 36,4/17 48,70/23500 300 12,6/8 16,9/11 21,1/14 25,4/17 34,0/23

700 700 400 900 37,9/7 50,6/10 63,4/13 76,2/16 102/22 128/27450 750 33,0/7 44,1/10 55,2/13 66,4/16 88,8/22 111/27500 600 27,6/7 36,8/10 46,1/13 55,4/16 74,1/22 92,9/27600 300 14,9/7 19,9/10 24,9/13 30,0/16 40,1/22 50,2/27

800 800 450 1050 50,2/6 67,1/9 84,0/11 101/14 135/19 169/24500 900 44,8/6 59,8/9 74,8/11 90,0/14 120/19 151/24600 600 32,1/6 42,9/9 53,7/11 64,5/14 86,3/19 108/24700 300 17,2/6 23,0/9 28,/11 34,5/14 46,2/19 57,9/24

900 900 500 1200 64,2/6 85,8/8 107/10 129/12 172,5/17 216/21600 900 51,6/6 68,9/8 86,2/10 104/12 138/17 174/21700 600 36,7/6 49,0/8 61,3/10 73,7/12 98,4/17 123/21800 300 19,5/6 26,0/8 32,6/10 39,1/12 52,3/17 65,5/21

1000 1000 600 1200 73,4/5 98,0/7 123/9 147,3/11 197/15 247/19700 900 58,5/5 78,0/7 97,7/9 117,3/11 157/15 196/19800 600 41,3/5 55,1/7 68,9/9 82,8/11 111/15 139/19900 300 21,8/5 29,1/7 36,4/9 43,7/11 58,4/15 73,1/19

1100 1100 700 1200 82,5/4 110/6 138/8 165,6/10 221/13 277/17800 900 65,3/4 97,2/6 109/8 131/10 175/13 219/17900 600 45,8/4 61,2/6 76,5/8 92,0/10 123/13 154/171000 300 24,1/4 32,1/6 40,2/8 48,3/10 64,5/13 80,7/17

1200 1200 800 1200 91,7/6 122/6 153/7 184/9 246/12 308/16900 900 72,2/6 96,3/6 120/7 145/9 193/12 242/161000 600 50,4/6 67,3/6 84,1/7 101/9 135/12 169/161100 300 26,3/6 35,2/6 44,0/7 52,8/9 70,5/12 88,3/16

Wall thickness mm

3,0 4,0 5,0 6,0 8,0 10





Butt Weld Fittings

51

3/4”x1/2” 26,7 21,3 38 2,11 2,11 0,101”x3/4” 33,4 26,7 51 2,77 2,11 0,131”x1/2” 21,3 2,77 2,11 0,121 1/4”x1” 42,2 33,4 2,77 2,77 0,181 1/4”x3/4” 26,7 2,77 2,11 0,181 1/4”x1/2” 21,3 2,77 2,11 0,171 1/2”x1 1/4” 48,3 42,2 64 2,77 2,77 0,211 1/2”x1” 33,4 2,77 2,77 0,201 1/2”x3/4” 26,7 2,77 2,11 0,202”x1 1/2” 60,3 48,3 76 2,77 2,77 0,312”x1 1/4” 42,2 2,77 2,77 0,302”x1” 33,4 2,77 2,77 0,282 1/2”x2” 73,0 60,3 89 3,05 2,77 0,472 1/2”x1 1/2” 48,3 3,05 2,77 0,442 1/2”x1 1/4” 42,2 3,05 2,77 0,433”x2 1/2” 88,9 73,0 3,05 3,05 0,593”x2” 60,3 3,05 2,77 0,553”x1 1/2” 48,3 3,05 2,77 0,514”x3” 114,3 88,9 102 3,05 3,05 0,874”x2 1/2” 73,0 3,05 3,05 0,834”x2” 60,3 3,05 2,77 0,785”x4” 141,3 114,3 127 3,40 3,05 1,495”x3” 88,9 3,40 3,05 1,456”x5” 168,3 141,3 140 3,40 3,40 2,086”x4” 114,3 3,40 3,05 1,956”x3” 88,9 3,40 3,05 1,828”x6” 219,1 168,3 152 3,76 3,40 3,198”x4” 114,3 3,76 3,05 3,0110”x8” 273,0 219,1 178 4,19 3,76 5,2010”x6” 168,3 4,19 3,40 5,0012”x10” 323,9 273,0 203 4,57 4,19 7,9812”x8” 219,1 4,57 3,76 7,67

Dim.

NPS D D1 H T T1 Weight kg/pce

Stock standard: Sch 10S size DN 15-100 and DN 150 in grade 316, EN 1,4462 (2205) and DN25- DN100 EN 1,4547 (254 SMO).

EC OT-No.: 420CC OT-No.: 421ANSI

Reducers CC, EC, ASTM A 403 WPS / WPW / WPWX

Butt Weld Fittings

52

10 17,2 2,0 2,5 40 7 0,02/16*15 21,3 2,0 2,5 45 7 0,03/16*20 26,9 2,0 3,0 58 8 0,06/16*

3,0 4,0 8 0,07/1625 33,7 2,0 3,0 68 10 0,08/16*

3,0 4,0 10 0,10/1632 42,4 2,0 3,0 78 12 0,10/16*

3,0 4,0 12 0,13/1640 44,5 2,0 3,0 88 17 0,14/16

48,3 2,0 3,0 15 0,13/16*3,0 4,0 15 0,17/16

50 57,0 3,0 4,0 102 18 0,23/1660,3 2,0 3,0 20 0,18/16*

3,0 4,0 20 0,23/1665 76,1 2,0 3,0 20 0,24/16*

3,0 4,0 20 0,32/1680 88,9 2,0 3,0 138 25 0,31/16**

3,2 4,0 25 0,42/16*100 114,3 2,0 2,5 25 0,31/10

3,2 4,0 25 0,49/16*125 139,7 2,0 2,5 25 0,39/10

3,2 4,0 25 0,64/16**150 168,3 2,0 2,5 212 25 0,47/10

3,0 3,5 25 0,64/103,0 4,0 25 0,73/104,0 5,0 25 0,93/16

200 219,1 2,0 2,5 268 30 0,67/103,0 4,0 30 1,06/10

DN D1 T T1 D H Weight kg/pce / Design pressure bar

OT-No.: 500ISOPressed collars PN10-PN16 (EN 1092-1 see remarks below)



250 273,00 3 328 31 1,20/64 31 1,60/10

300 323,90 3 378 35 1,50/44 35 1,90/10

DN A F=SP d1 H5 Weight kg/pce / Design pressure bar

OT-No.: 500 ISO Collars welded and pressed

Design pressure is calculated for grade EN 1.4307 at 20°C and fulfils the requirementsin EN 13480, Part 2, Part 3 and Part 5, EN 13445-3.Full face gasket with thickness ≥ 1,0 mm. Gasket factor 3.50 and design seating stress ≥ 45 Mpa.See also appendix H in EN13445-3.Collars according to EN 1092-1 are calculated according to EN 1591-1.*) In accordance with EN 1092-1 PN16 Type 37.**) In accordance with EN 1092-1 PN10 Type 37.The designation of a EN 1092-1 DN50 collar is. Collar EN 1092-1/37/DN50/PN19/1.4432.

The pressures are calculated for grade EN 1.4307 at 20°C. Full face gasket with thickness ≥ 1,5 mm. Gasket factor 2,85 and design seating stress ≥ 30 Mpa. See also appendix H in EN 13445-3.

Butt Weld Fittings

53

10 16 2,0 2,5 45 8 0,03/16*15 20 2,0 3,0 45 9 0,04/16*20 25 2,0 3,0 58 10 0,06/16*25 28 2,0 3,0 68 12 0,08/16*

30 2,0 3,0 12 0,08/16*32 38 2,0 3,0 78 14 0,11/16*

40 2,0 3,0 14 0,11/16*50 51 2,0 2,5 102 18 0,15/16**

54 2,0 3,0 18 0,18/1665 64 2,0 2,5 18 0,14/16

69 2,0 3,0 122 20 0,25/16**70 2,0 3,0 20 0,25/1671 3,0 4,0 124 20 0,35/1674 2,0 3,0 22 0,26/1676 3,0 4,0 22 0,34/1679 2,0 3,0 138 23 0,32/16

DN = ID

80 81 3,2 4,0 138 23 0,42/16**84 2,0 3,0 24 0,32/16**86 3,0 4,0 24 0,42/16

100 102 2,0 2,5 158 27 0,33/16104 2,0 2,5 27 0,33/16106 3,2 4,0 27 0,52/16**108 4,0 5,0 27 0,68/16

125 129 2,0 2,5 188 27 0,44/6131 3,0 4,0 27 0,69/10133 4,0 5,0 27 0,91/16

150 154 2,0 2,5 212 27 0,51/4156 3,0 4,0 27 0,80/10158 4,0 5,0 27 1,00/16

200 204 2,0 2,0 268 26 0,56/2206 3,0 3,0 26 0,83/6208 4,0 4,0 26 1,10/10

DN A SP F d1 H5 Weight kg/pce / Design pressure bar


Pressed collars PN16 up to DN 100 (EN 1092-1 see remarks below)

Stock standard: EN 1.4307 and 1.4432Design pressure is calculated at 20˚C and fulfil the requirementsin EN 13480, Part 2, Part 3 and Part 5, EN 13445-3.Full face gasket with thickness ≥ 1,0mm.Gasket factor 3.5 and design seating stress ≥ 45 Mpa. See also appendix H in EN13445-3.Collars according to EN 1092-1 are calculated according to EN 1591-1.*) In accordance with EN 1092-1 PN16 Type 37.**) In accordance with EN 1092-1 PN10 Type 37.

Butt Weld Fittings

54

250 255 2,5 320 31 4 1,00256 3,0 320 31 6 1,20

300 305 2.5 370 35 4 1,75306 3,0 370 35 4 1,50

350 355 2,5 430 43 4 1,60356 3,0 430 43 4 2,20

400 406 3,0 482 43 2 2,50408 4,0 482 43 4 3,30

450 456 3,0 532 45 2 2,90458 4,0 532 45 4 3,80

500 506 3,0 585 45 2 3,20508 4,0 585 45 4 4,20

600 606 3,0 685 45 2 3,70608 4,0 685 45 4 4,90

Design

pressure Weight

DN A SP=F d1 H5 bar kg/pce


Collars welded and pressed


250 256 3 320 65 16 1,90273 3 328 70 10 1,98

300 306 3 370 55 16 2,00323,9 3 378 68 10 2,26

350 356 3 430 55 16 2,50400 408 4 482 65 10 4,20500 508 4 585 75 10 5,70600 608 4 685 80 10 7,20

Design

pressure Weight

DN S SP=F d1 H5 bar* kg/pce


Collars welded and pressed (long neck)


The pressures are calculated for grade En 1.4307 at 20°C.Full-face gasket with thickness ≥ 1,5 mm. Gasket factor 4,94 and design seating stress 90 MPa.Se also Appendix H in EN 13445-3.

The pressures are calculated for grade En 1.4307 at 20°C.Full-face gasket with thickness ≥ 1,5 mm. Gasket factor 4,94 and design seating stress 90 MPa.Se also Appendix H in EN 13445-3.*) Note. To obtain the pressure ratings in the table the collars are dimensioned for special fl angesthat have less bore diameter and chamfer, and the other measures are at least the sameas corresponding EN 1092-1 fl anges type 01.

A

Butt Weld Fittings

55

15-32 Use PN 40 (SSG 7468)40 48,3 88 42 6,0 2,0 3,0 0,33 50 60,3 102 45 8,0 2,0 3,0 0,5365 76,1 122 45 10 2,6 3,0 0,84 80 88,9 138 50 10 2,6 4,0 1,00100 114,3 158 52 10 3,2 4,0 1,30 125 139,7 188 55 10 3,2 5,0 1,70150 168,3 212 55 10 4,0 6,0 2,30200 219,1 268 62 11 4,0 7,0 3,50250 273,0 320 70 12 5,0 8,0 5,10 300 323,9 378 78 12 5,0 10 7,80*350 355,6 438 82 15 5,0 10 12,0*400 406,4 490 85 15 6,3 12 13,5*450 457 550 85 15 6,3 12 17,0*500 508 610 90 18 8,0 12 21,0*600 610 725 95 18 8,0 14 29,0*

Weight

DN A d1 H4 F S T1 kg/pce

OT-No.: 502ISO Weldring necks PN 16 in accordance with EN 13480 (SSG 7466; SFS 4168)

15-32 Use PN 40 (SSG 7468)40-250 Use PN 16 (SSG 7466)300 323,9 370 68 12 3,6 7,0 6,0350 355,6 430 68 12 3,6 7,0 8,8400 406,4 482 72 12 3,6 8,0 11,8450 457 532 72 12 3,6 9,0 13,1*500 508 585 75 15 4,0 9,0 15,3*600 610 685 80 15 5,0 10 23,3*

Weight


OT-No.: 502ISOWeldring necks PN 10 in accordance with EN 13480 (SSG 7465; SF 4167)

Stock standard: EN 1.4432*) No stock standard

Design pressure is calculated for grade EN 1.4307 at 20°C.Use with EN 1092-1 type 02 flanges.

A



Butt Weld Fittings

56

15 21,3 45 38 6 2,6 3,2 0,1020 26,9 58 40 6 2,6 3,2 0,1725 33,7 68 40 7 2,6 3,5 0,2532 42,4 78 42 8 2,6 3,6 0,3840 48,3 88 45 8 2,6 3,6 0,48*50 60,3 102 48 10 3,2 4,0 0,70*65 76,1 122 52 11 3,2 5,0 1,10*80 88,9 138 58 12 4,0 6,0 1,60*100 114,3 162 65 14 4,0 7,0 2,40*125 139,7 188 68 16 4,0 7,0 3,20*150 168,3 218 75 18 4,0 8,0 4,60*200 219,1 285 88 20 5,0 11 8,70*250 273,0 345 105 22 6,0 13 15,0*300 323,9 410 115 24 8,0 16 24,0*350 355,6 465 125 24 8,0 16 32,0*400 406,4 535 135 24 10 18 42,0*450 457,0 560 135 56 12 20 46,0*500 508,0 615 140 30 15 20 57,0*600 610,0 735 150 35 15 24 88,0*

Weight



15-100 Use PN 40 (SSG 7468)125 139,7 188 68 12 3,6 6 2,70150 168,3 212 75 12 4 7 3,50200 219,1 278 80 13 5 10 6,20250 273,0 335 88 15 6,3 10 8,80300 323,9 395 92 16 8 11 13,2350 355,6 450 100 18 8 13 19,5400 406,4 505 110 18 8 14 23,8450 457 555 120 20 8 15 31,0500 508 615 125 22 10 17 42,0600 610 720 125 24 12 18 55,0

Weight



Stock standard: EN 1.4432No stock standard


A

A


Design pressure is calculated for grade EN 1.4307 at 20°C. Use with EN 1092-1 type 02 flanges.

Butt Weld Fittings

57

20 24 58 40 6,0 2,0 2,0 0,1525 29 68 40 6,0 2,0 2,0 0,2032 36 78 40 6,0 2,0 2,0 0,2540 44 88 45 6,0 2,0 2,0 0,3050 54 102 45 8,0 2,0 2,0 0,5065 70 122 45 8,0 2,5 2,5 0,6070 75 122 45 8,0 2,5 2,5 0,7080 86 138 50 10 3,0 3,0 0,90100 106 158 50 10 3,0 4,0 1,20125 131 188 50 10 3,0 5,0 1,70150 156 212 50 10 3,0 5,0 1,90200 206 268 65 10 3,0 7,0 3,60250 257 320 65 12 3,5 8,0 4,80300 308 370 65 12 4,0 10 6,50350 359 430 70 15 4,5 10 9,60*400 410 482 80 15 5,0 12 12,3*450 460 532 85 15 5,0 12 16,3*500 510 585 95 18 5,0 12 21,2*600 612 685 100 18 6,0 14 29,6*700 720 795 110 20 10 14 40,0*800 824 900 110 22 12 16 50,5*900 924 1000 115 24 12 18 65,5*1000 1030 1115 130 32 15 18 93,0*1200 1230 1330 130 32 15 22 131*

Weight



Weldring necks PN16 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7366)

20-250 Use PN 16 (SSG 7366)300 306 370 60 12 3,0 8,0 5,30350 356 430 60 12 3,5 8,0 6,80400 407 482 65 12 3,5 8,0 8,80450 457 532 70 15 3,5 8,0 12,1500 507 585 75 15 4,0 9,0 14,9600 608 685 80 15 4,0 10 19,2700 710 800 90 15 4,5 12 28,6*800 810 905 100 15 5,0 13 37,3*900 916 1005 110 18 6,0 15 53,0*1000 1016 1110 120 18 8,0 18 71,0*1200 1220 1330 130 22 10 18 104*

Weight



Weldring necks PN 10 in accordance with EN 13480 (EN 1092-1 Type 35M; SSG 7365)

Stock standard: EN 1.4301 and EN 1.4432*) No stock standard


A

A



Butt Weld Fittings

58

20-150 Use DN 20-150 (SSG 7370)200 210 278 65 12 5,0 9,5 5,5250 263 335 75 15,5 6,5 12 8,6*300 315 390 80 16 7,5 12,5 11,6* 350 360 450 85 18 5,0 12 17,2*400 412 505 95 18 6,0 13,5 23,0*450 466 555 105 20 8,0 15 27,3*500 516 615 115 22 8,0 15 34,6* 600 624 720 115 24 12 18 51,0*700 730 820 115 30 15 20 65,0*800 830 930 115 34 15 22 85,0*900 936 1030 130 40 18 24 114*

Weight




20 25 58 40 6 2,5 3,0 0,1625 30 68 40 6 2,5 3,0 0,2132 37 78 40 6 2,5 3,5 0,3040 45 88 45 8 2,5 3,5 0,3850 55 102 45 8 2,5 4,0 0,6165 70 122 45 10 2,5 4,5 0,7580 85 138 55 10 2,5 4,5 1,20100 106 162 55 10 3,0 5,0 1,60125 132 188 55 12 3,5 6,0 2,40150 158 218 65 12 4,0 7,0 3,30200 212 285 85 20 6,0 10 7,6*250 266 345 100 22 8,0 12 12,9*300 318 410 110 24 9,0 15 20,0*350 370 465 120 27 10 15 26,0*400 424 535 130 25 12 20 38,0*450 474 560 135 26 12 20 39,0*500 530 615 140 30 15 20 49,0*600 630 735 150 35 15 24 94,0*

Weight





A

A




Butt Weld Fittings

59

10 17,7 40 6,0 0,0515 21,8 45 6,0 0,0620 27,4 58 6,0 0,1025 34,2 68 6,0 0,1432 43,0 78 6,0 0,1640 48,8 88 6,0 0,2150 60,8 102 8,0 0,3565 76,6 122 8,0 0,4880 89,4 138 10 0,70100 115,5 158 10 0,75125 140,7 184 10 0,90150 169,3 212 10 1,04200 220,1 268 10 1,50

Weight

DN d D T kg/pce

OT-No.: 501ISO Weld-on plate collars

10 15,0 40 6,0 0,0515 20,5 45 6,0 0,0620 25,5 58 6,0 0,1025 30,5 68 6,0 0,1432 39,0 78 6,0 0,1740 45,0 88 6,0 0,2250 55,0 102 8,0 0,3865 70,0 122 8,0 0,5070 75,0 122 10 0,5975 80,0 138 10 0,7980 85,0 138 10 0,75100 105,0 158 10 0,88125 130,0 184 10 1,10150 155,0 212 10 1,30200 205,0 268 10 1,90250 255,0 320 12 2,80300 306,0 370 12 3,30350 356,0 430 12 4,40400 406,0 482 12 5,10450 456 532 15 7,10500 508 585 15 8,00

Weight

DN d D T kg/pce


Weld-on plate collars

Stock standard: EN 1.4404 ≤ DN 80EN 1.4432 > DN 80

Stock standard: EN 1.4404 ≤ DN 80EN 1.4432 > DN 80

Butt Weld Fittings

60

,

200 208 4 260 28 1.71 1.10

200 208 4 260 28 1,10/10250 258 4 310 28 1,40/10300 308 4 360 28 1,70/10350 358 4 410 28 2,00/6400 408 4 480 38 3,20/6450 458 4 530 38 3,30/6500 510 5 590 48 5,50/6600 610 5 690 48 6,80/6700 710 5 785 48 8,30/4800 810 5 885 48 9,40/4

press ure Weight

DN D1 T D H kg/pce / Design pressure bar


Angle collars

200 219,1 4 271 28 1,20/10250 273,0 4 320 28 1,40/10300 323,9 4 376 28 1,80/10350 355,6 4 410 28 2,10/6400 406,4 4 480 38 3,30/6450 457 4 530 38 3,50/6500 508 5 590 48 5,70/6600 610 5 690 48 7,20/6

presure Weight

DN D1 T D H kg/pce / Design pressure bar

OT-No.: 503ISO Angle collars

Stock standard: EN 1.4432




Butt Weld Fittings

61

33,7 2,0 27 5 38 25 0,08/100*48,3 2,0 32 6 38 25 0,10/10060,3 2,0 48 9 38 22 0,14/6076,1 2,0 60 11 38 18 0,17/5088,9 2,0 64 12 51 26 0,28/80*88,9 3,0 64 12 51 26 0,42/100114,3 2,0 88 17 64 34 0,45/60*114,3 3,0 88 17 64 34 0,67/100139,7 3,0 112 21 76 40 1,00/40168,3 3,0 130 26 89 44 1,42/40219,1 3,0 175 34 102 45 2,26/25273,0 3,0 215 42 127 56 3,40/16273,0 4,0 215 42 127 56 4,52/30*323,9 4,0 250 50 152 68 6,40/25355,6 4,0 285 57 165 70 7,72/20*406,4 4,0 325 65 178 71 9,73/20*457 4,0 365 73 203 83 12,10/16*508 4,0 406 80 229 92 15,10/16*610 4,0 488 98 267 108 18,20/14*

Weight

D T R r K H1 kg/pce

OT-No.: 60ISO Caps, ISO 5251, EN 10253-4

54 2,0 40 8 25 10 0,02 0,10/8084 2,0 64 13 38 15 0,1 0,20/5086 3,0 64 13 38 15 0,1 0,30/80*104 2,0 80 16 44 15 0,1 0,30/40106 3,0 80 16 44 15 0,1 0,40/60*129 2,0 100 20 50 15 0,3 0,40/30131 3,0 100 20 50 15 0,3 0,60/50*154 2,0 120 24 56 15 0,5 0,50/25156 3,0 120 24 56 15 0,5 0,80/40*204 2,0 160 32 74 20 1.0 0,90/20*206 3,0 160 32 74 20 1,0 1,30/25208 4,0 160 32 74 20 1,0 1,70/40*254 2,0 200 40 86 20 2,0 1,30/16*256 3,0 200 40 86 20 2,0 2,00/25258 4,0 200 40 86 20 2,0 2,60/25*306 3,0 240 48 100 20 3,5 2,70/20308 4,0 240 48 100 20 3,5 3,60/25*356 3,0 280 56 115 20 5,6 3,70/16358 4,0 280 56 115 20 5,6 4,90/20*406 3,0 320 65 128 20 8,7 4,70/16408 4,0 320 65 128 20 8,7 6,30/20*456 3,0 360 72 140 20 14,0 6,30/12*458 4,0 360 72 140 20 14,0 7,80/16*506 3,0 400 80 152 20 19,0 7,20/12*508 4,0 400 80 152 20 19,0 9,60/16*606 3,0 480 96 180 20 30,0 12,70/10*608 4,0 480 96 180 20 30,0 13,50/12*708 4,0 560 112 205 20 46,0 18,20/12*710 5,0 560 112 205 20 46,0 24,80/15*

Volume Weight

D T R r K H1 Litres kg/pce


Caps, SMS 482; SSG 1369

Stock standard: EN 1.4432*) No stock std.

The pressures are calculated according to EN 13445-3 for grade EN 1.4432 at 20°C

Stock standard: EN 1.4432*) No stock std.

The pressures are calculated according to EN 13445-3 for grade EN 1.4432 at 20°C

Butt Weld Fittings

62

1 1/2” 48,3 10S 2,77 38 0,141 1/2” 48,3 40S 3,68 38 0,232” 60,3 10S 2,77 38 0,172” 60,3 40S 3,91 38 0,272 1/2” 73,0 10S 3,05 38 0,252 1/2” 73,0 40S 5,16 38 0,453” 88,9 10S 3,05 51 0,403” 88,9 40S 5,49 51 0,714” 114,3 10S 3,05 64 0,654” 114,3 40S 6,02 64 1,225” 141,3 10S 3,40 76 1,025” 141,3 40S 6,55 76 1,846” 168,3 10S 3,40 89 1,366” 168,3 40S 7,11 89 3,238” 219,1 10S 3,76 102 2,498” 219,1 40S 8,18 102 5,6710” 273,0 10S 4,19 127 4,9010” 273,0 40S 9,27 127 9,2112” 323,9 10S 4,57 152 6,5312” 323,9 40S 9,53 152 13,114” 355,6 10S 4,78 165 8,1614” 355,6 STD 9,53 165 16,216” 406,4 10S 4,78 178 14,516” 406,4 STD 9,53 178 22,018” 457 10S 4,78 203 18,018” 457 STD 9,53 203 27,020” 508 10S 5,54 229 27,220” 508 STD 9,53 229 34,024” 610 10S 6,35 267 34,524” 610 STD 9,53 267 44,5

Weight

N.P.S. D SCH T H kg/pce

OT-No.: 62ANSI Caps

Stock standard: 316/316L

Butt Weld Fittings

63

10 14,0–18,0 25 40 7,50 2 M6x2015 20,0–22,0 25 44 7,50 2 M6x2020 23,0–24,0 25 46 7,50 3 M6x20

25,0–28,0 25 52 7,50 3 M6x2025 30,0–33,7 25 57 7,50 3 M6x2032 35,0–38,0 25 63 7,50 3 M6x2032-40 42,4–44,5 30 69 7,50 3 M6x2040 48,3 30 73 7,50 3 M6x20350 353,0–356,0 50 413 18,00 4 M16x50400 404,0–406,0 50 464 18,00 4 M16x50450 454,0–458 50 515 18,00 4 M16x60500 504,0–508 50 567 18,00 4 M16x60600 604,0–608 50 669 18,00 4 M16x65700 711 50 770 18,00 4 M16x65

Tube size Bolt

DN D B L d T size

OT-No.: 74ISO/MetricTube clamps

50 53,0–54,0 40 87 9,50 3 20 M8x2557,0–60,3 40 91 9,50 3 20 M8x25

65 68,0–70,0 40 100 9,50 3 22 M8x2570 73,0–76,1 40 120 9,50 3 22 M8x2580 82,0–84,0 40 131 9,50 3 30 M8x25

88,9 40 120 9,50 3 30 M8x25100 102,0–106,0 40 148 12,00 3 30 M10x25

114,3 40 156 12,00 3 30 M10x35125 127,0–131,0 40 177 12,00 3 30 M10x25

139,7 40 186 12,00 3 30 M10x35150 152,0–156,0 40 198 12,00 3 30 M10x25

168,3 40 206 12,00 4 30 M10x35200 202,0–206,0 40 244 15,00 4 30 M12x35

219,1 40 262 15,00 4 30 M12x35250 252,0–256,0 40 298 15,00 4 30 M12x50

273,0 40 316 15,00 4 30 M12x50300 302,0–306,0 50 369 18,00 4 38 M16x50

323,9 50 390 18,00 4 38 M16x50

Tube size Bolt

DN D B L d T B1 size

OT-No.: 74ISO/MetricTube clamps



Threaded Fittings

64

Threaded Fittings

Threaded fittings of stainless steel have for more than 70 years been manufactured in our main mill in Molkom,

Sweden. Together with our mills in Tuusula and Tallin, Outokumpu Stainless Tubular Products is today

Europe’s largest manufacturer within its branch. Thousands of articles are manufactured from tubes and bars

with ultra modern CIM steered CNC-machines to the industries highest quality demands.

The base is a comprehensive QS according to EN ISO 9001:2001. All manufactured products are approved

by a Notified Body to the European Pressure equipment PED 97/23/EC and by TÜV certified to AD 2000

Merkblatt W0. This allows the use of these products in applications according to category IV in the PED

Directive.

All products with the R-designation are calculated according to EN 13480-3.

An extensive stock programme together with Outokumpu Stainless distribution network secures a high

availability and fast delivery service for any application.

Technical Information

• Benefit: Threaded fittings are produced from tubes and bars for highest quality.• Application: Anywhere you need a reliable and safe tube connection.• Calculations: EN 13480 Metallic industrial piping has been used for design pressure calculations.• Material: All threaded fittings are produced from harmonized material. See each data sheet for steel grades.

Other steel grades upon request.

Threads

Whitworth threads

Threaded fittings have Whitworth pipe threads (BSP) as standard:- male threads, taper external according to ISO 7/1- male threads, parallel external according to ISO 228/1- female threads, parallel internal according to ISO 228/1- female threads, taper internal according to ISO 7/1

NPT threads

Fittings with NPT threads (American Standard National Pipe Thread) are available upon request. However, certain items - sockets, double nipples and welding nipples - are also available from stock with NPT threads.

Symbols for threads

Pipe threads and their symbols

Pipe threads where pressure-tight joints are made on the threads.Rp= Parallel internal ISO 7/1 - Rp 1½”Rc= Taper internal ISO 7/1 - Rc 1½”R=Taper external ISO 7/1 - R 1½”ISO 7/2 deals with the inspection of these threads.

Pipe threads where pressure-tight joints are not made on the threads.G=Parallel internal ISO 228/1-G1½” One tolerance class onlyG…A=Parallel external ISO 228/1-G1½”A Tighter class of toleranceG…B=Parallel external ISO 228/1-G1½”B Wider class of toleranceISO 228/2 deals with the inspection of these threads.

65

CouplingsR-131PAGE 66

CouplingsR-131SPAGE 66

CouplingsR-131UPAGE 67

CouplingsLR-131PAGE 67

CouplingsLR-131UPAGE 67

CouplingsLR-131SPAGE 68

CouplingsLR-131OPAGE 68

CouplingsLR-131UOPAGE 68

Union-LPAGE 69

Union-SPAGE 69

Bite-ring couplingsR-1321PAGE 70


Threaded Fittings

OT-No.: 800R-131 Couplings

6 1/8” 32 12 10,0 15,0 15,0 24 10,0 0,06 11-1131-01 11-1131-518 1/4” 38 12 13,0 20,5 20,5 30 10,0 0,11 11-1131-02 11-1131-5210 3/8” 41 14 14,0 24,0 24,0 38 10,0 0,18 11-1131-03 11-1131-5315 1/2” 46 17 16,0 29,0 29,0 43 10,0 0,24 11-1131-04 11-1131-5420 3/4” 50 20 18,0 35,0 35,0 50 10,0 0,35 11-1131-05 11-1131-5525 1” 56 23 22,0 44,0 44,0 60 10,0 0,56 11-1131-06 11-1131-5632 1 1/4” 62 25 24,0 52,0 52,0 67 6,4 0,69 11-1131-07 11-1131-5740 1 1/2” 64 26 25,5 58,0 58,0 73 6,4 0,86 11-1131-08 11-1131-5850 2” 67 28 26,0 71,5 71,5 87 6,4 1,21 11-1131-09 11-1131-5965 2 1/2” 70 29 28,0 88,0 88,0 110 4,0 1,84 11-1131-10 _80 3” 75 31 30,0 102,0 102,0 128 4,0 2,62 11-1131-11 _

66

L1 L2 Design Article code Article code

ISO ISO pressure Weight BSP-threaded NPT-threaded

DN Dim. L 228/1 228/1 D D1 NW Mpa kg/pce EN 1.4404 EN 1.4404

OT-No.: 800R-131S Couplings

14,0/10,0 38 2,0 2,0 14,0 14,0 24 10,0 0,06 11-7131-0118,0/14,0 40 2,0 2,0 18,0 18,0 38 10,0 0,18 11-7131-0221,3/16,0 40 2,7 2,7 21,3 21,3 38 10,0 0,18 11-7131-0325,0/20,0 44 2,5 2,5 25,0 25,0 43 10,0 0,23 11-7131-0426,9/23,0 44 2,0 2,0 26,9 26,9 43 10,0 0,27 11-7131-0530,0/25,0 47 2,5 2,5 30,0 30,0 50 10,0 0,34 11-7131-0633,7/27,2 53 3,3 3,3 33,7 33,7 60 10,0 0,59 11-7131-0734,0/30,0 53 2,0 2,0 34,0 34,0 60 10,0 0,51 11-7131-0838,0/34,0 57 2,0 2,0 38,0 38,0 60 6,4 0,48 11-7131-0942,4/36,0 57 3,2 3,2 42,4 42,4 68 6,4 0,73 11-7131-1044,5/40,0 57 2,3 2,3 44,5 44,5 68 6,4 0,65 11-7131-1148,3/43,0 63 2,7 2,7 48,3 48,3 74 6,4 0,87 11-7131-1251,0/47,0 63 2,0 2,0 51,0 51,0 74 6,4 0,86 11-7131-1354,0/50,0 69 2,0 2,0 54,0 54,0 88 6,4 1,26 11-7131-1460,3/55,0 74 2,7 2,7 60,3 60,3 88 6,4 1,21 11-7131-1577,0/71,0 80 3,0 3,0 77,0 77,0 110 6,4 1,91 11-7131-1689,0/81,7 83 3,7 3,7 89,0 89,0 128 6,4 2,85 11-7131-17

Design

pressure Weight Article code

Dim. L T T1 D D1 NW Mpa kg/pce EN 1.4404

Threaded Fittings

Threaded Fittings

67

OT-No.: 800R-131U Couplings

6 1/8” 40,5 9 10,0 15,0 5,0 24 10,0 0,07 11-2131-01 11-2131-51

8 1/4” 47,0 12 13,0 20,5 7,5 30 10,0 0,12 11-2131-02 11-2131-52

10 3/8” 53,0 14 14,0 24,0 11,0 38 10,0 0,20 11-2131-03 11-2131-53

15 1/2” 62,0 17 16,0 29,0 14,0 43 10,0 0,29 11-2131-04 11-2131-54

20 3/4” 66,0 18 28,0 35,0 19,0 50 10,0 0,42 11-2131-05 11-2131-55

25 1” 74,0 20 22,0 44,0 24,0 60 10,0 0,67 11-2131-06 11-2131-56

32 1 1/4” 81,0 21 24,0 52,0 31,0 67 6,4 0,90 11-2131-07 11-2131-57

40 1 1/2” 84,0 22 25,5 58,0 38,0 73 6,4 1,09 11-2131-08 11-2131-58

50 2” 87,0 23 26,0 71,5 49,0 87 6,4 1,53 11-2131-09 11-2131-59

65 2 1/2” 97,0 25 28,0 88,0 65,0 110 4,0 2,32 11-2131-10 _

80 3” 109,0 33 30,0 102,0 76,0 125 4,0 3,42 11-2131-11 _

L1 L2 Design Article code Article code

ISO ISO pressure Weight BSP-threaded NPT-threaded

DN Dim. L 7/1 228/1 D d NW Mpa kg/pce EN 1.4404 EN 1.4404

OT-No.: 800LR-131 Couplings

6 1/8” 32 12 12 17,0 17,0 27 10,0 0,08 11-3131-01

8 1/4” 32 12 12 17,0 17,0 27 10,0 0,07 11-3131-02

10 3/8” 38 14 14 20,5 20,5 30 10,0 0,09 11-3131-03

15 1/2” 41 16 16 24,5 24,5 36 10,0 0,13 11-3131-04

20 3/4” 47 17 17 31,0 31,0 43 10,0 0,21 11-3131-05

25 1” 53 20 20 38,0 38,0 50 10,0 0,30 11-3131-06

32 1 1/4” 58 22 22 47,0 47,0 60 6,4 0,43 11-3131-07

40 1 1/2” 63 23 23 54,0 54,0 68 6,4 0,58 11-3131-08

50 2” 72 27 27 66,5 66,5 88 6,4 1,08 11-3131-09

65 2 1/2” 80 31 31 98,0 98,0 128 4,0 3,40 11-3131-10

80 3” 80 31 31 98,0 98,0 128 4,0 2,45 11-3131-11

L1 L2 Design

ISO ISO pressure Weight Article code

DN Dim. L 228/1 228/1 D D1 NW Mpa kg/pce EN 1.4404

OT-No.: 800LR-131U Couplings

6 1/8” 42 12 12 17,0 5,0 24 10,0 0,09 11-5131-01

8 1/4” 42 12 12 17,0 7,5 30 10,0 0,92 11-5131-02

10 3/8” 49 14 14 20,5 11,0 38 10,0 0,11 11-5131-03

15 1/2” 56 17 16 24,5 14,5 43 10,0 0,17 11-5131-04

20 3/4” 63 18 17 31,0 19,0 50 10,0 0,26 11-5131-05

25 1” 69 20 20 38,0 24,5 60 10,0 0,39 11-5131-06

32 1 1/4” 74 21 22 47,0 30,0 68 6,4 0,59 11-5131-07

40 1 1/2” 80 22 23 54,0 38,0 74 6,4 0,73 11-5131-08

50 2” 87 23 27 66,5 49,0 88 6,4 1,30 11-5131-09

65 2 1/2” 101 30 31 98,0 65,0 110 4,0 3,57 11-5131-10

80 3” 101 30 31 98,0 75,0 128 4,0 2,91 11-5131-11

L1 L2 Design Article code

ISO ISO pressure Weight BSP-threaded

DN Dim. L 7/1 228/1 D d NW Mpa kg/pce EN 1.4404

OT-No.: 800LR-131S Couplings

14/10 32,0 2,0 2,0 14,0 14,0 27 10,0 0,07 11-8131-0118/14 37,0 2,0 2,0 18,0 18,0 30 10,0 0,09 11-8131-0221,3/16 40,5 2,7 2,7 21,3 21,3 36 10,0 0,15 11-8131-0325/20 48,0 2,5 2,5 25,0 25,0 43 10,0 0,24 11-8131-0426,9/23 48,0 2,0 2,0 26,9 26,9 43 10,0 0,22 11-8131-0530/25 48,0 2,5 2,5 30,0 30,0 43 10,0 0,22 11-8131-0633,7/27,2 52,0 3,3 2,3 33,7 33,7 50 10,0 0,35 11-8131-0834/30 52,0 2,0 2,0 34,0 34,0 50 10,0 0,30 11-8131-0738/34 58,0 2,0 2,0 38,0 38,0 60 6,4 0,32 11-8131-0942,4/36 58,0 3,2 3,2 42,4 42,4 60 6,4 0,50 11-8131-1044,5/40 58,0 2,3 2,3 44,5 44,5 60 6,4 0,42 11-8131-1148,3/43 63,0 2,7 2,7 48,3 48,3 68 6,4 0,62 11-8131-1251/47 63,0 2,0 2,0 51,0 51,0 68 6,4 0,52 11-8131-1354/50 63,0 2,0 2,0 54,0 54,0 68 6,4 0,47 11-8131-1460,3/55 69,0 2,7 2,7 60,3 60,3 88 6,4 1,08 11-8131-15

68

Design


Dim. L T T1 D D1 NW Mpa kg/pce EN 1.4404

OT-No.: 800LR-131O Couplings

8 1/4” 32 12,0 12,0 17,0 17,0 27 10,0 0,07 11-4131-0210 3/8” 38 14,0 14,0 20,5 20,5 30 10,0 0,08 11-4131-0315 1/2” 41 16,0 16,0 24,5 24,5 36 10,0 0,13 11-4131-0420 3/4” 47 17,0 17,0 31,0 31,0 43 10,0 0,21 11-4131-0525 1” 53 19,5 10,5 38,0 38,0 50 10,0 0,29 11-4131-0632 1 1/4” 58 22,0 22,0 47,0 47,0 60 6,4 0,43 11-4131-0740 1 1/2” 63 23,0 23,0 54,0 54,0 68 6,4 0,57 11-4131-0850 2” 72 27,0 27,0 66,5 66,5 88 6,4 1,08 11-4131-09

L1 L2 Design


DN Dim. L 228/1 228/1 D D1 NW Mpa kg/pce EN 1.4404

OT-No.: 800LR-131UO Couplings

8 1/4” 42 12 12 17,0 7,5 27 10,0 0,08 11-6131-0210 3/8” 49 14 14 20,5 11,0 30 10,0 0,10 11-6131-0315 1/2” 56 17 16 24,5 14,5 36 10,0 0,17 11-6131-0420 3/4” 63 18 17 31,0 19,0 43 10,0 0,26 11-6131-0525 1” 69 20 20 38,0 24,5 50 10,0 0,38 11-6131-0632 1 1/4” 74 21 23 47,0 30,0 60 6,4 0,57 11-6131-0740 1 1/2” 80 22 23 54,0 38,0 68 6,4 0,72 11-6131-0850 2” 87 23 27 66,5 49,0 88 6,4 1,29 11-6131-09

L1 L2 Design


DN Dim. L 7/1 228/1 D d NW Mpa kg/pce EN 1.4404

Threaded Fittings

26,9x2,3 40 26,9 22,3 10,0 0,19 14-504-310 14-503-31030,0x2,0 40 31,0 26,0 10,0 0,20 14-504-320 14-503-32033,7x2,6 50 34,2 28,5 10,0 0,24 14-504-330 14-503-33042,4x2,6 50 42,4 37,2 10,0 0,37 14-504-340 14-503-34044,5x2,9 50 46,0 38,7 10,0 0,35 14-504-350 14-503-35048,3x2,6 60 49,0 43,1 10,0 0,52 14-504-360 14-503-36054,0x2,0 60 54,0 50,0 10,0 0,66 14-504-370 14-503-37057,0x2,9 60 58,0 51,2 10,0 0,63 14-504-380 14-503-38060,3x2,9 60 60,3 54,5 10,0 0,85 14-504-390 14-503-39076,1x2,9 60 76,1 70,3 4,0 1,00 14-504-400 14-503-40084,0x2,0 60 84,0 80,0 4,0 1,10 14-504-410 14-503-41088,9x3,6 60 89,0 81,7 4,0 1,10 14-504-420 14-503-420104,0x2,0 60 104,0 100,0 4,0 1,60 14-504-430 14-503-430108,0x4,0 60 109,0 100,0 4,0 1,70 14-504-440 14-503-440114,3x3,6 70 114,3 107,1 4,0 2,30 14-504-450 14-503-450129,0x2,0 70 129,0 125,0 4,0 2,40 14-504-460 14-503-460133,0x4,0 70 134,0 125,0 4,0 2,50 14-504-470 14-503-470139,7x3,6 70 141,3 132,5 2,5 2,60 14-504-480 14-503-480154,0x2,0 70 154,0 150,0 2,5 3,00 14-504-490 14-503-490159,0x4,5 70 160,0 150,0 2,5 3,20 14-504-500 14-503-500168,3x4,0 70 170,0 160,3 2,5 3,70 14-504-510 14-503-510205,0x2,5 70 205,0 200,0 1,6 7,10 14-504-520 14-503-520219,1x3,6 80 220,0 211,9 1,6 7,90 14-504-530 14-503-530255,0x2,5 80 255,0 250,0 1,6 11,10 14-504-540 14-503-540

Threaded Fittings

69

OT-No.: 839Union-L Design Article code Article code

Dim. pressure Weight Teflon Nitril

mm L D d Mpa kg/pce EN 1.4404 EN 1.4404

Union-S AISI 304 PN10

19,05x1,65 60 19,05 15,75 28,0 45,6026,9x1,6 50 26,90 23,70 28,0 45,6033,7x 2 50 33,70 29,70 53,6 84,5442,4x1,5 50 42,40 39,40 53,6 84,5448,3x2,02 50 48,30 44,30 53,6 84,5460,3x2,15 60 60,30 56,00 67,0 96,4976,1x 1 60 76,10 74,10 80,6 112,51

Dim. Clamps

mm 2xL D1 d A S

Assembly instructions: 1. Check the threads of bolt and nuts. 2. Check the O-ring gasket and insert it into the groove. 3. Fix the clamps with bolt and nuts and alternate the tightening of the bolts.

The gaps between the clamp ends on either side should be equal.

OT-No.: 810R-1321 Bite-ring couplings

5,0 39 10,5 24 5,1 4 14 10 0,04 11-1321-016,0 39 10,5 24 6,1 5 14 10 0,04 11-1321-028,0 40 10,0 25 8,1 6 17 10 0,06 11-1321-0310,0 42 11,0 27 10,2 8 19 10 0,07 11-1321-0410,2 42 11,0 27 10,4 8 19 10 0,07 11-1321-0512,0 43 11,0 28 12,2 10 22 10 0,09 11-1321-0614,0 46 12,0 30 14,2 12 27 10 0,15 11-1321-0715,0 46 12,0 30 15,2 12 27 10 0,15 11-1321-0816,0 46 12,0 30 16,2 12 27 10 0,14 11-1321-0917,0 51 12,0 31 17,2 15 32 10 0,21 11-1321-1017,2 51 12,0 31 17,4 15 32 10 0,21 11-1321-1118,0 54 11,5 31 18,2 15 32 10 0,21 11-1321-1220,0 55 13,8 35 20,2 18 36 10 0,28 11-1321-1321,3 55 14,0 35 21,5 19 36 10 0,28 11-1321-1423,0 55 13,3 35 23,2 19 36 10 0,26 11-1321-1525,0 63 14,0 36 25,2 22 38 10 0,30 11-1321-16

70

Design


Dim. L L1 L2 d d1 NW Mpa kg/pce EN 1.4404


5 5,1 4 20 10,5 27,0 14 10 0,04 11-1323-016 6,1 5 20 10,5 27,0 14 10 0,05 11-1323-028 8,1 6 21 10,0 28,5 17 10 0,06 11-1323-0310 10,2 8 22 11,0 30,5 19 10 0,09 11-1323-0410,2 10,4 8 22 11,0 30,5 19 10 0,09 11-1323-0512 12,2 10 24 11,0 33,5 22 10 0,11 11-1323-0614 14,3 12 30 12,0 42,0 27 10 0,21 11-1323-0715 15,2 12 30 12,0 42,0 27 10 0,21 11-1323-0816 16,2 12 30 12,0 42,0 27 10 0,20 11-1323-0917 17,2 15 32 12,0 45,5 32 10 0,32 11-1323-1017,2 17,4 15 32 12,0 45,5 32 10 0,32 11-1323-1118 18,2 15 32 11,5 45,5 32 10 0,33 11-1323-1220 20,2 18 35 13,8 51,5 36 10 0,44 11-1323-1321,3 21,5 19 35 14,0 51,5 36 10 0,44 11-1323-1423 23,2 19 35 13,3 51,5 36 10 0,44 11-1323-1525 25,2 22 38 14,0 56,0 38 10 0,55 11-1323-16

Design


Dim. d d1 H L1 L NW Mpa kg/pce EN 1.4404

Threaded Fittings

71





SocketsR-201PAGE 74

Reducing socketsR-202PAGE 74

Half socketsR-203PAGE 75

Long socketsR-402PAGE 76

Special socketsR-404PAGE 77

Special socketsR-408PAGE 77

NipplesR-206PAGE 78

Double nipplesR-207PAGE 78

Threaded Fittings

72

Threaded Fittings


5x1/8” 31 10,5 7,5 23,5 4 5,1 14 10 0,03 11-1322-015x1/4” 35 10,5 11,5 27,5 4 5,1 14 10 0,03 11-1322-026x1/8” 31 10,5 7,5 23,5 5 6,1 14 10 0,04 11-1322-036x1/4” 35 10,5 11,5 27,5 5 6,1 14 10 0,04 11-1322-046x3/8” 35 10,5 11,5 27,5 5 6,1 14 10 0,05 11-1322-056x1/2” 37 13,8 15,5 33,5 5 6,1 14 10 0,08 11-1322-318x1/4” 37 10,0 11,5 29,0 6 8,1 17 10 0,04 11-1322-068x3/8” 38 14,0 15,5 29,0 6 8,1 17 10 0,05 11-1322-3210x1/4” 38 10,0 11,5 30,0 6 10,2 19 10 0,05 11-1322-0710x3/8” 38 11,0 11,5 30,0 7 10,2 19 10 0,06 11-1322-0810,2x1/4” 38 11,0 11,5 30,0 8 10,2 19 10 0,06 11-1322-0910,2x3/8” 38 11,0 11,5 30,0 7 10,2 19 10 0,06 11-1322-1012x1/4” 39 11,0 11,5 31,5 8 12,2 22 10 0,07 11-1322-1112x3/8” 40 11,0 11,5 31,5 7 12,2 22 10 0,08 11-1322-1212x1/2” 41 11,0 11,5 33,5 10 12,2 22 10 0,09 11-1322-1314x1/2” 44 10,5 13,5 35,0 5 14,2 27 10 0,12 11-1322-1415x3/8” 42 11,0 13,5 33,0 10 15,2 27 10 0,12 11-1322-1515x1/2” 44 12,0 13,5 35,0 12 15,2 27 10 0,12 11-1322-1615x3/4” 45 14,0 15,5 37,0 19 15,2 27 10 0,15 11-1322-3416x1/2” 44 12,0 11,5 35,0 10 16,2 32 10 0,13 11-1322-1717x1/2” 45 12,0 13,5 35,0 12 17,2 32 10 0,15 11-1322-1817x3/4” 47 12,0 15,5 37,0 12 17,2 32 10 0,15 11-1322-1917,2x1/2” 45 12,0 13,5 35,0 12 17,4 32 10 0,16 11-1322-2017,2x3/4” 47 12,0 13,5 37,0 14 17,4 32 10 0,17 11-1322-2118x1/2” 45 12,0 15,5 35,0 15 18,2 32 10 0,18 11-1322-2218x3/8” 43 13,8 13,5 33,0 15 18,2 32 10 0,15 11-1322-3020x1/2” 47 13,3 15,5 37,0 19 20,2 36 10 0,19 11-1322-3320x3/4” 49 12,0 13,5 39,0 14 20,2 36 10 0,20 11-1322-2321,3x3/4” 49 12,0 15,5 39,0 15 21,5 36 10 0,19 11-1322-2423x3/4” 49 11,5 11,5 39,0 10 23,5 36 10 0,18 11-1322-2525x3/4” 49 11,5 13,5 39,0 15 25,2 38 10 0,21 11-1322-26

Design

L2 pressure Weight Article code

Dim. L L1 ISO 7/1 L3 d d1 NW Mpa kg/pce EN 1.4404

Threaded Fittings


5 54 10,5 27 40 5,3 4 14 10 0,06 11-1324-01

6 54 10,5 27 40 6,3 5 14 10 0,06 11-1324-02

8 58 10,0 29 42 8,3 6 17 10 0,09 11-1324-03

10 60 11,0 30 44 10,4 8 19 10 0,12 11-1324-04

10,2 60 11,0 30 44 10,4 8 19 10 0,12 11-1324-05

12 64 11,0 32 48 12,3 10 22 10 0,13 11-1324-06

14 74 12,0 37 60 14,3 12 27 10 0,22 11-1324-07

15 74 12,0 37 60 15,3 12 27 10 0,27 11-1324-08

16 74 12,0 37 60 16,3 12 27 10 0,26 11-1324-09

17 82 12,0 41 64 17,4 15 32 10 0,41 11-1324-10

17,2 82 12,0 41 64 17,4 15 32 10 0,41 11-1324-11

18 82 11,5 41 64 18,4 15 32 10 0,39 11-1324-12

20 90 13,8 45 70 20,4 18 36 10 0,53 11-1324-13

21,3 90 14,0 45 70 21,7 19 36 10 0,51 11-1324-14

23 90 13,3 45 70 23,4 19 36 10 0,50 11-1324-15

25 96 14,0 48 76 25,4 22 38 10 0,47 11-1324-16

73

Design


Dim. L L1 H L2 d d1 NW Mpa kg/pce EN 1.4404


6x1/8” 31,0 27,0 10,5 6 8,1 5 24,0 14 10 0,04 11-1325-01

6x1/4” 31,0 27,0 10,5 9 8,1 5 24,0 14 10 0,04 11-1325-02

8x1/4” 33,5 28,5 10,0 9 10,1 6 26,0 17 10 0,05 11-1325-03

8x3/8” 34,0 30,5 10,0 9 10,3 8 25,5 19 10 0,08 11-1325-10

10x1/4” 36,0 30,5 11,0 9 12,3 8 27,5 19 10 0,07 11-1325-04

10x3/8” 36,0 30,5 11,0 9 12,3 8 27,5 19 10 0,07 11-1325-05

12x1/4” 41,5 32,5 11,0 9 14,3 8 32,0 22 10 0,09 11-1325-06

12x3/8” 41,5 32,5 11,0 9 14,3 10 32,0 22 10 0,09 11-1325-07

12x1/2” 41,5 32,5 11,0 12 14,3 10 32,0 22 10 0,10 11-1325-08

14x1/2” 47,0 36,0 12,0 12 16,3 12 35,0 27 10 0,20 11-1325-09

Design


Dim. L L1 L2 ISO 7/1 d d1 H NW Mpa kg/pce EN 1.4404


6x1/8” 40 10,5 14,0 6,2 5 24,0 14 10 0,05 11-1326-01

6x1/4” 40 10,5 14,0 6,2 5 24,0 14 10 0,07 11-1326-02

8x1/4” 42 10,0 14,0 8,1 6 26,0 17 10 0,07 11-1326-03

10x1/4” 44 11,0 14,5 10,2 8 27,5 19 10 0,08 11-1326-04

10x3/8” 44 11,0 14,5 10,2 8 27,5 19 10 0,08 11-1326-05

12x1/4” 48 11,0 17,0 12,2 8 32,0 22 10 0,09 11-1326-06

12x3/8” 48 11,0 17,0 12,2 10 32,0 22 10 0,10 11-1326-07

12x1/2” 48 11,0 17,0 12,2 10 32,0 22 10 0,11 11-1326-08

Design


Dim. L L1 ISO 7/1 d d1 H NW Mpa kg/pce EN 1.4404

74

Threaded Fittings

OT-No.: 801R-201 Sockets

6 1/8” 14,0 17 10,0 0,02 11-0201-01 11-0201-518 1/4” 18,5 25 10,0 0,03 11-0201-02 11-0201-5210 3/8” 21,5 26 10,0 0,03 11-0201-03 11-0201-5315 1/2” 26,5 34 10,0 0,07 11-0201-04 11-0201-5420 3/4” 32,5 36 10,0 0,09 11-0201-05 11-0201-5525 1” 40,0 43 10,0 0,14 11-0201-06 11-0201-5632 1 1/4” 48,3 48 6,4 0,21 11-0201-07 11-0201-5740 1 1/2” 54,5 48 6,4 0,29 11-0201-08 11-0201-5850 2” 66,3 56 6,4 0,40 11-0201-09 11-0201-5965 2 1/2” 82,0 65 4,0 0,68 11-0201-10 _80 3” 95,0 71 4,0 0,97 11-0201-11 _100 4” 125,0 85 4,0 1,80 11-0201-12 _

Design Article code Article code

L pressure Weight BSP-threaded NPT-threaded

DN Dim. D ISO 228/1 Mpa kg/pce EN 1.4404 EN 1.4404

OT-No.: 801R-202 Reducing sockets

8x6 1/4”x1/8” 27 12 18,8 14,0 10,0 0,04 11-0202-01 11-0202-5110 x 8 3/8”x1/4” 30 12 21,4 19,0 10,0 0,04 11-0202-02 11-0202-5215x8 1/2”x1/4” 36 16 27,5 19,0 10,0 0,08 11-0202-03 11-0202-5315x10 1/2”x3/8” 36 16 27,5 23,0 10,0 0,08 11-0202-04 11-0202-5420x10 3/4”x3/8” 39 17 32,5 23,0 10,0 0,10 11-0202-05 11-0202-5520x15 3/4”x1/2” 39 17 32,5 28,0 10,0 0,11 11-0202-06 11-0202-5625x15 1”x1/2” 45 20 39,5 28,0 10,0 0,18 11-0202-07 11-0202-5725x20 1”x3/4” 45 20 39,5 32,5 10,0 0,15 11-0202-08 11-0202-5832x15 1 1/4”x1/2” 52 22 49,5 28,0 6,4 0,27 11-0202-19 _32x20 1 1/4”x3/4” 50 22 49,5 32,5 6,4 0,27 11-0202-09 11-0202-5932x25 1 1/4”x1” 50 22 49,5 39,5 6,4 0,24 11-0202-10 11-0202-6040x20 1 1/2”x3/4” 55 22 54,7 32,5 6,4 0,35 11-0202-11 11-0202-6140x25 1 1/2”x1” 55 22 54,7 39,5 6,4 0,31 11-0202-12 11-0202-6240x32 1 1/2”x1 1/4” 55 22 54,7 49,5 6,4 0,31 11-0202-13 11-0202-6350x25 2”x1” 65 27 69,5 39,5 6,4 0,58 11-0202-14 11-0202-6450x32 2”x1 1/4” 65 27 69,5 49,5 6,4 0,52 11-0202-15 11-0202-6550x40 2”x1 1/2” 65 27 69,5 55,5 6,4 0,53 11-0202-16 11-0202-6665x50 2 1/2”x2” 74 32 84,0 69,5 4,0 0,81 11-0202-17 _80x50 3”x2” 78 35 99,5 69,5 4,0 1,10 11-0202-20 _80x65 3”x2 1/2” 80 35 99,5 84,0 4,0 1,25 11-0202-18 _


L1 pressure Weight BSP-threaded NPT-threaded

DN Dim. L ISO 228-1 D D1 Mpa kg/pce EN 1.4404 EN 1.4404

Threaded Fittings

OT-No.: 801R-203 Half sockets

6 1/8” 10,0 14,0 10,0 0,01 11-0203-018 1/4” 10,0 18,5 10,0 0,01 11-0203-0210 3/8” 12,0 21,5 10,0 0,02 11-0203-0315 1/2” 15,0 26,5 10,0 0,03 11-0203-0420 3/4” 17,0 32,5 10,0 0,04 11-0203-0525 1” 19,5 40,0 10,0 0,06 11-0203-0632 1 1/4” 22,0 48,3 6,4 0,09 11-0203-0740 1 1/2” 22,0 54,5 6,4 0,13 11-0203-0850 2” 26,0 66,3 6,4 0,19 11-0203-0965 2 1/2” 30,5 82,0 4,0 0,30 11-0203-1080 3” 34,0 95,0 4,0 0,45 11-0203-11

75

Design

L pressure Weight Article code

DN Dim. ISO 228/1 D Mpa kg/pce EN 1.4404

76

Threaded Fittings

OT-No.: 801R-402 Long sockets

6 1/8” 14,0 34 0,03 19-0402-0114,0 50 0,03 19-0402-2114,0 60 0,04 19-0402-51

8 1/4” 18,5 50 0,06 19-0402-0218,5 60 0,07 19-0402-52

10 3/8” 21,5 50 0,06 19-0402-2321,5 52 0,07 19-0402-0321,5 60 0,08 19-0402-5321,5 70 0,09 19-0402-3321,5 80 0,10 19-0402-63

15 1/2” 26,3 50 0,10 19-0402-2426,3 60 0,12 19-0402-5426,3 68 0,13 19-0402-0426,3 70 0,13 19-0402-3426,3 80 0,15 19-0402-6426,3 96 0,18 19-0402-44

20 3/4” 32,6 60 0,15 19-0402-5532,6 50 0,12 19-0402-2532,6 70 0,18 19-0402-3532,6 72 0,18 19-0402-0532,6 80 0,21 19-0402-6532,6 96 0,25 19-0402-45

25 1” 39,8 60 0,20 19-0402-5639,8 70 0,24 19-0402-3639,8 80 0,27 19-0402-6639,8 86 0,29 19-0402-0639,8 96 0,33 19-0402-46

32 1 1/4” 48,3 70 0,30 19-0402-3748,3 80 0,36 19-0402-6748,3 96 0,42 19-0402-07

40 1 1/2” 55,6 70 0,33 19-0402-3855,6 80 0,37 19-0402-6855,6 96 0,47 19-0402-08

50 2” 66,3 96 0,58 19-0402-49

Article code

L Weight BSP-threaded

DN Dim. D ISO 228/1 kg/pce EN 1.4404

Threaded Fittings

OT-No.: 801R-404 Special sockets

8 1/4” 21 12,0 5 18,0 13,5 2,0 0,02 19-0404-0210 3/8” 23 13,0 5 21,0 17,2 2,0 0,02 19-0404-0315 1/2” 27 16,0 6 25,0 21,3 2,0 0,03 19-0404-0420 3/4” 28 17,5 6 32,0 26,9 2,0 0,06 19-0404-0525 1” 31 20,0 6 39,0 33,7 2,6 0,09 19-0404-0632 1 1/4” 34 22,5 6 48,0 42,4 2,6 0,13 19-0404-0740 1 1/2” 36 22,5 8 55,0 48,3 2,6 0,17 19-0404-0850 2” 40 26,5 8 65,0 60,3 2,6 0,19 19-0404-09

77

L1 Weight Article code

DN Dim. L ISO 228-1 L2 D D1 T kg/pce EN 1.4404

OT-No.: 801R-408 Special sockets

8 1/4” 18,5 110,0 11 0,17 19-0408-0218,5 100,0 11 0,13 19-0408-2218,5 80,0 11 0,75 19-0408-72

10 3/8” 21,5 110,0 12 0,15 19-0408-0321,5 100,0 12 0,14 19-0408-3321,5 120,0 12 0,16 19-0408-4321,5 80,0 12 0,11 19-0408-73

15 1/2” 26,3 115,0 15 0,24 19-0408-0426,3 200,0 15 0,43 19-0408-2426,3 100,0 15 0,21 19-0408-4426,3 120,0 15 0,25 19-0408-5426,3 150,0 15 0,31 19-0408-6426,3 80,0 15 0,16 19-0408-74

20 3/4” 32,6 115,0 17 0,32 19-0408-0532,6 100,0 17 0,28 19-0408-3532,6 120,0 17 0,34 19-0408-4532,6 150,0 17 0,43 19-0408-5532,6 200,0 17 0,58 19-0408-6532,6 80,0 17 0,22 19-0408-75

25 1” 39,8 120,0 20 0,46 19-0408-0639,8 100,0 20 0,38 19-0408-2639,8 150,0 20 0,58 19-0408-4639,8 200,0 20 0,78 19-0408-5639,8 80,0 20 0,35 19-0408-76

32 1 1/4” 48,3 120,0 22 0,60 19-0408-0748,3 100,0 22 0,48 19-0408-27

40 1 1/2” 55,6 120,0 22 0,66 19-0408-0855,6 100,0 22 0,55 19-0408-28

50 2” 66,3 120,0 26 0,82 19-0408-0966,3 100,0 26 0,68 19-0408-29

65 2 1/2” 82,0 120,0 31 1,10 19-0408-1080 3” 95,0 120,0 34 1,40 19-0408-11

Article code

L1 Weight BSP-threaded

DN Dim. D L ISO 228/1 kg/pce EN 1.4404

78

Threaded Fittings

OT-No.: 802R-206 Nipples

6 1/8” 16 6,2 10,0 0,01 11-0206-018 1/4” 18 8,9 10,0 0,01 11-0206-0210 3/8” 22 12,6 10,0 0,02 11-0206-0315 1/2” 25 16,1 10,0 0,02 11-0206-0420 3/4” 30 21,7 10,0 0,03 11-0206-0525 1” 35 27,3 10,0 0,06 11-0206-0632 1 1/4” 38 36,0 6,4 0,07 11-0206-0740 1 1/2” 38 41,9 6,4 0,08 11-0206-0850 2” 45 53,1 6,4 0,14 11-0206-0965 2 1/2” 55 68,9 4,0 0,24 11-0206-1080 3” 60 80,9 4,0 0,30 11-0206-11

Design


DN Dim. ISO 228/1 d Mpa kg/pce EN 1.4404

OT-No.: 802R-207 Double nipples

6 1/8” 21,0 7,5 7,5 5,0 12 10,0 0,01 11-0207-01 11-0207-518 1/4” 28,0 11,0 11,0 7,5 14 10,0 0,02 11-0207-02 11-0207-5210 3/8” 29,0 11,5 11,5 10,0 19 10,0 0,03 11-0207-03 11-0207-5315 1/2” 36,0 15,0 15,0 14,0 22 10,0 0,05 11-0207-04 11-0207-5420 3/4” 41,0 16,5 16,5 19,0 30 10,0 0,09 11-0207-05 11-0207-5525 1” 46,5 19,0 19,0 24,5 36 10,0 0,13 11-0207-06 11-0207-5632 1 1/4” 54,0 21,5 21,5 32,0 46 6,4 0,21 11-0207-07 11-0207-5740 1 1/2” 54,0 21,5 21,5 38,0 50 6,4 0,26 11-0207-08 11-0207-5850 2” 65,5 25,8 25,8 50,0 65 6,4 0,43 11-0207-09 11-0207-5965 2 1/2” 76,5 30,3 30,3 65,0 80 4,0 0,63 11-0207-10 _80 3” 85,0 33,5 33,5 76,0 90 4,0 0,83 11-0207-11 _100 4” 94,0 34,5 34,5 100,0 126 4,0 2,02 11-0207-12 _


L1 L2 pressure Weight BSP-threaded NPT-threaded

DN Dim. L ISO 7/1 ISO 7/1 d NW Mpa kg/pce EN 1.4404 EN 1.4404

79

Welding nipplesR-208 PAGE 80

Reducing nipplesR-209PAGE 81

Barrel nipplesR-210PAGE 81

BushingsR-211PAGE 82

Reducing nipplesR-212PAGE 83

Long screwsR-228PAGE 83

PlugsR-235PAGE 84

PlugsR-236PAGE 84

PlugsR-237PAGE 85

PlugsR-238PAGE 85

Hexagonal capsR-231PAGE 86

Round capsR-232PAGE 86

Threaded Fittings

Threaded Fittings

80

OT-No.: 802R-208 Z Welding nipples (parallel thread)

8 1/4” 25 13,5 14 2,3 0,01 19-0208-0210 3/8” 25 17,2 15 2,3 0,02 19-0208-0315 1/2” 30 21,3 19 2,6 0,03 19-0208-0420 3/4” 30 26,9 20 2,6 0,03 19-0208-0525 1” 35 33,7 24 3,2 0,06 19-0208-0632 1 1/4” 35 42,4 25 3,2 0,08 19-0208-0740 1 1/2” 35 48,3 26 3,2 0,08 19-0208-0850 2” 40 60,3 28 3,6 0,15 19-0208-09

L1 Weight Article code

DN Dim. L D ISO 228/1 T kg/pce EN 1.4404

OT-No.: 802R-207 Z Nipples (parallel thread)

8 1/4” 20,5 6,5 6,5 7,5 17 0,015 19-0207-0210 3/8” 20,5 6,5 6,5 10,0 22 0,025 19-0207-0315 1/2” 32,0 11,0 11,0 14,0 27 0,050 19-0207-0420 3/4” 32,0 11,0 11,0 19,0 32 0,065 19-0207-0525 1” 35,0 12,0 12,0 24,5 41 0,120 19-0207-0632 1 1/4” 41,0 14,0 14,0 32,0 50 0,210 19-0207-0740 1 1/2” 41,0 14,0 14,0 38,0 55 0,230 19-0207-0850 2” 46,0 16,0 16,0 50,0 65 0,305 19-0207-09

L1 L2 Weight Article code

DN Dim. L ISO 228/1 ISO 228/1 d NW kg/pce EN 1.4404

OT-No.: 802R-208 Welding nipples

6 1/8” 30 10,2 6 2,0 10,0 0,01 11-0208-01 11-0208-518 1/4” 30 13,5 9 2,3 10,0 0,02 11-0208-02 11-0208-5210 3/8” 30 17,2 9 2,3 10,0 0,02 11-0208-03 11-0208-5315 1/2” 35 21,3 12 2,6 10,0 0,04 11-0208-04 11-0208-5420 3/4” 40 26,9 13 2,6 10,0 0,05 11-0208-05 11-0208-5525 1” 40 33,7 15 3,2 10,0 0,08 11-0208-06 11-0208-5632 1 1/4” 50 42,4 17 3,2 6,4 0,14 11-0208-07 11-0208-5740 1 1/2” 50 48,3 17 3,2 6,4 0,15 11-0208-08 11-0208-5850 2” 55 60,3 22 3,6 6,4 0,23 11-0208-09 11-0208-5965 2 1/2” 60 76,1 24 3,6 4,0 0,32 11-0208-10 _80 3” 65 88,9 27 4,0 4,0 0,46 11-0208-11 _100 4” 90 114,3 33 4,0 4,0 0,84 11-0208-12 _



DN Dim. L D ISO 7/1 T Mpa kg/pce EN 1.4404 EN 1.4404

Also available as stock standard in 1.4571

Threaded Fittings

81

OT-No.: 802R-209 Reducing nipples

8x6 1/4” x 1/8” 25,0 7,5 11,0 7,5 5,0 14 0,02 11-0209-01 11-0209-5110x6 3/8” x 1/8” 25,5 7,5 11,5 10,0 5,0 19 0,03 11-0209-02 11-0209-5210x8 3/8” x 1/4” 29,0 11,0 11,5 10,0 7,5 19 0,03 11-0209-03 11-0209-5315x6 1/2” x 1/8” 30,0 7,5 15,0 14,0 5,0 22 0,05 11-0209-04 11-0209-5415x8 1/2” x 1/4” 33,0 11,0 15,0 14,0 7,5 22 0,04 11-0209-05 11-0209-5515x10 1/2” x 3/8” 33,5 11,5 15,0 14,0 10,0 22 0,05 11-0209-06 11-0209-5620x8 3/4” x 1/4” 37,0 11,0 16,5 19,0 7,5 30 0,07 11-0209-07 11-0209-5720x10 3/4” x 3/8” 37,0 11,5 16,5 19,0 10,0 30 0,08 11-0209-08 11-0209-5820x15 3/4” x 1/2” 40,5 15,0 16,5 19,0 14,0 30 0,09 11-0209-09 11-0209-5925x8 1” x 1/4” 40,0 11,0 19,0 24,5 7,5 36 0,11 11-0209-10 11-0209-6025x10 1” x 3/8” 40,5 11,5 19,0 24,5 10,0 36 0,13 11-0209-11 11-0209-6125x15 1” x 1/2” 44,0 15,0 19,0 24,5 14,0 36 0,12 11-0209-12 11-0209-6225x20 1” x 3/4” 45,5 16,5 19,0 24,5 19,0 36 0,13 11-0209-13 11-0209-6332x15 1 1/4” x 1/2” 48,0 15,0 21,5 31,0 14,0 46 0,20 11-0209-14 11-0209-6432x20 1 1/4” x 3/4” 49,5 16,5 21,5 31,0 19,0 46 0,25 11-0209-15 11-0209-6532x25 1 1/4” x 1” 52,0 19,0 21,5 31,0 24,5 46 0,26 11-0209-16 11-0209-6640x15 1 1/2” x 1/2” 48,0 15,0 21,5 38,0 14,0 50 0,28 11-0209-17 11-0209-6740x25 1 1/2” x 1” 52,0 19,0 21,5 38,0 24,5 50 0,30 11-0209-18 11-0209-6840x32 1 1/2” x 1 1/4” 54,0 21,5 21,5 38,0 31,0 50 0,29 11-0209-19 11-0209-6950x25 2” x 1” 59,0 19,0 25,8 49,0 24,5 65 0,50 11-0209-20 11-0209-7050x32 2” x 1 1/4” 62,0 21,5 25,8 49,0 31,0 65 0,50 11-0209-21 11-0209-7150x40 2” x 1 1/2” 62,0 21,5 25,8 49,0 38,0 65 0,48 11-0209-22 11-0209-7265x20 2 1/2” x 3/4” 63,0 16,5 30,3 63,0 19,0 80 0,74 11-0209-23 _65x50 2 1/2” x 2” 73,0 25,8 30,3 63,0 49,0 80 0,82 11-0209-24 _80x50 3” x 2” 78,0 25,8 33,5 75,0 49,0 90 1,08 11-0209-25 _80x65 3” x 2 1/2” 82,0 30,3 33,5 75,0 63,0 90 0,93 11-0209-26 _40x20 1 1/2” x 3/4” 49,0 16,5 21,5 38,0 19,0 50 0,29 11-0209-27 _

Article code Article code

L1 L2 Weight BSP-threaded NPT-threaded

DN Dim. L ISO 7/1 ISO 7/1 d d1 NW kg/pce EN 1.4404 EN 1.4404

OT-No.: 802R-210 Barrel nipples

6 1/8” 40 6 6 10,2 2,0 10 0,02 11-0210-01 11-0210-518 1/4” 40 9 9 13,5 2,3 10 0,02 11-0210-02 11-0210-5210 3/8” 40 9 9 17,2 2,3 10 0,03 11-0210-03 11-0210-5315 1/2” 60 12 12 21,3 2,6 10 0,07 11-0210-04 11-0210-5420 3/4” 60 13 13 26,9 2,6 10 0,07 11-0210-05 11-0210-5525 1” 60 15 15 33,7 3,2 10 0,12 11-0210-06 11-0210-5632 1 1/4” 80 17 17 42,4 3,2 6,4 0,21 11-0210-07 11-0210-5740 1 1/2” 80 17 17 48,3 3,2 6,4 0,24 11-0210-08 11-0210-5850 2” 100 22 22 60,3 3,6 6,4 0,42 11-0210-09 11-0210-5965 2 1/2” 100 24 24 76,1 3,6 4 0,53 11-0210-10 –80 3” 120 27 27 88,9 4,0 4 0,76 11-0210-11 –100 4” 150 33 33 114,3 4,0 4 1,3 11-0210-12 –


L1 L2 pressure Weight BSP-threaded NPT-threaded

DN Dim. L ISO 7/1 ISO 7/1 D T Mpa kg/pce EN 1.4404 EN 1.4404

Also available as stock standard in 1.4571

OT-No.: 802R-211 Bushings

8x6 1/4”x1/8” 17,0 11,0 14 10,0 0,02 11-0211-01 11-0211-5110x6 3/8”x1/8” 17,5 11,5 19 10,0 0,03 11-0211-02 11-0211-5210x8 3/8”x1/4” 17,5 11,5 19 10,0 0,02 11-0211-03 11-0211-5315x6 1/2”x1/8” 21,0 15,0 22 10,0 0,05 11-0211-04 11-0211-5415x8 1/2”x1/4” 21,0 15,0 22 10,0 0,04 11-0211-05 11-0211-5515x10 1/2”x3/8” 21,0 15,0 22 10,0 0,02 11-0211-06 11-0211-5620x8 3/4”x1/4” 24,5 16,5 30 10,0 0,09 11-0211-07 11-0211-5720x10 3/4”x3/8” 24,5 16,5 30 10,0 0,07 11-0211-08 11-0211-5820x15 3/4”x1/2” 24,5 16,5 30 10,0 0,05 11-0211-09 11-0211-5925x8 1”x1/4” 27,0 19,0 36 10,0 0,15 11-0211-10 11-0211-6025x10 1”x3/8” 27,0 19,0 36 10,0 0,15 11-0211-11 11-0211-6125x15 1”x1/2” 27,0 19,0 36 10,0 0,12 11-0211-12 11-0211-6225x20 1”x3/4” 27,0 19,0 36 10,0 0,07 11-0211-13 11-0211-6332x15 1 1/4”x1/2” 32,5 21,5 46 6,4 0,30 11-0211-26 _32x20 1 1/4”x3/4” 32,5 21,5 46 6,4 0,19 11-0211-14 11-0211-6432x25 1 1/4”x1” 32,5 21,5 46 6,4 0,12 11-0211-15 11-0211-6540x15 1 1/2”x1/2” 32,5 21,5 50 6,4 0,35 11-0211-16 11-0211-6640x20 1 1/2”x3/4” 32,5 21,5 50 6,4 0,36 11-0211-17 11-0211-6740x25 1 1/2”x1” 32,5 21,5 50 6,4 0,26 11-0211-18 11-0211-6840x32 1 1/2”x1 1/4” 32,5 21,5 50 6,4 0,13 11-0211-19 11-0211-6950x25 2”x1” 40,0 26,0 65 6,4 0,68 11-0211-20 11-0211-7050x32 2”x1 1/4” 40,0 26,0 65 6,4 0,52 11-0211-21 11-0211-7150x40 2”x1 1/2” 40,0 26,0 65 6,4 0,40 11-0211-22 11-0211-7265x50 2 1/2”x2” 46,0 30,0 80 4,0 0,54 11-0211-23 _80x50 3”x2” 51,5 33,5 90 4,0 1,24 11-0211-24 _80x65 3”x2 1/2” 51,5 33,5 90 4,0 0,74 11-0211-25 _

82


L L1 pressure Weight BSP-threaded NPT-threaded

DN Dim. ISO 228/1 ISO 7/1 NW Mpa kg/pce EN 1.4404 EN 1.4404

Threaded Fittings

Threaded Fittings

83

OT-No.: 802R-212 Reducing nipples

8x6 1/4”x1/8” 28,0 6 20,5 15,5 17,5 5,0 0,03 19-0212-0110x6 3/8”x1/8” 26,5 6 19,0 14,0 21,5 5,0 0,04 19-0212-2410x8 3/8”x1/4” 30,0 9 19,0 14,0 21,5 7,5 0,04 19-0212-0215x8 1/2”x1/4” 32,0 9 21,0 16,0 29,5 7,5 0,08 19-0212-0315x10 1/2”x3/8” 32,0 9 20,5 15,5 29,5 10,0 0,08 19-0212-0420x10 3/4”x3/8” 35,0 9 23,5 18,5 34,5 10,0 0,10 19-0212-0520x15 3/4”x1/2” 37,0 12 22,0 17,0 34,5 14,0 0,11 19-0212-0625x10 1”x3/8” 40,0 9 28,5 23,5 39,5 10,0 0,13 19-0212-0725x15 1”x1/2” 42,0 12 27,0 22,0 39,5 14,0 0,13 19-0212-0825x20 1”x3/4” 45,0 13 28,5 22,0 39,5 19,0 0,14 19-0212-0932x15 1 1/4”x1/2” 48,0 9 33,0 28,0 49,5 14,0 0,22 19-0212-1032x20 1 1/4”x3/4” 48,0 13 30,0 25,0 49,5 19,0 0,22 19-0212-1132x25 1 1/4”x1” 50,0 15 31,0 26,0 49,5 24,5 0,24 19-0212-1240x20 1 1/2”x3/4” 52,0 13 35,5 30,5 54,5 19,0 0,25 19-0212-1340x25 1 1/2”x1” 52,0 15 33,0 28,0 54,5 24,5 0,26 19-0212-1440x32 1 1/2”x1 1/4” 54,0 17 32,5 32,0 54,5 27,5 0,27 19-0212-1550x25 2”x1” 56,0 15 37,0 32,0 69,5 24,5 0,45 19-0212-1650x32 2”x1 1/4” 56,0 17 34,5 29,5 69,5 32,0 0,45 19-0212-1750x40 2”x1 1/2” 58,0 17 36,5 31,5 69,5 38,0 0,47 19-0212-1865x32 2 1/2”x1 1/4” 60,0 17 38,5 33,5 84,5 32,0 0,60 19-0212-1965x40 2 1/2”x1 1/2” 60,0 17 38,5 33,5 84,5 38,0 0,62 19-0212-2065x50 2 1/2”x2” 65,0 22 38,5 34,0 84,5 50,0 0,62 19-0212-2180x50 3”x2” 68,0 22 42,0 37,0 99,5 50,0 0,88 19-0212-2280x65 3”x2 1/2” 68,0 24 42,0 37,0 99,5 65,0 0,89 19-0212-23

L1 L2 L3 Weight Article code

DN Dim. L ISO 7/1 ISO 228/1 D d kg/pce EN 1.4404

OT-No.: 802R-228 Long screws

6 1/8” 75 6 32 10,2 2,0 10,0 0,05 11-0228-018 1/4” 80 9 35 13,5 2,3 10,0 0,12 11-0228-0210 3/8” 100 9 40 17,2 2,3 10,0 0,11 11-0228-0315 1/2” 100 12 50 21,3 2,6 10,0 0,17 11-0228-0420 3/4” 120 13 55 26,9 2,6 10,0 0,26 11-0228-0525 1” 140 15 60 33,7 3,2 10,0 0,46 11-0228-0632 1 1/4” 150 17 70 42,4 3,2 6,4 0,67 11-0228-0740 1 1/2” 150 17 70 48,3 3,2 6,4 0,79 11-0228-0850 2” 170 22 81 60,3 3,6 6,4 1,08 11-0228-0965 2 1/2” 180 24 92 76,1 3,6 4,0 1,58 11-0228-1080 3” 200 27 101 88,9 4,0 4,0 1,65 11-0228-11

Design

L1 L2 pressure Weight Article code

DN Dim. L ISO 7/1 ISO 228/1 D T Mpa kg/pce EN 1.4404

OT-No.: 803R-235 Plugs

6 1/8” 14 8,0 13 10,0 0,01 11-0235-01 11-0235-518 1/4” 17 11,0 14 10,0 0,02 11-0235-02 11-0235-5210 3/8” 17 11,0 19 10,0 0,03 11-0235-03 11-0235-5315 1/2” 21 15,0 22 10,0 0,05 11-0235-04 11-0235-5420 3/4” 24 16,0 30 10,0 0,11 11-0235-05 11-0235-5525 1” 27 18,0 36 10,0 0,19 11-0235-06 11-0235-5632 1 1/4” 32 21,5 46 6,4 0,36 11-0235-07 11-0235-5740 1 1/2” 33 21,5 50 6,4 0,48 11-0235-08 11-0235-5850 2” 38 25,5 65 6,4 0,90 11-0235-09 11-0235-5965 2 1/2” 45 30,5 80 4,0 1,64 11-0235-10 _80 3” 48 33,5 90 4,0 2,32 11-0235-11 _

84



DN Dim. L ISO 7/1 NW Mpa kg/pce EN 1.4404 EN 1.4404


6 1/8” 13 7,0 14 10 0,01 11-0236-018 1/4” 16 10,0 19 10 0,02 11-0236-0210 3/8” 17 11,0 22 10 0,04 11-0236-0315 1/2” 22 14,0 27 10 0,07 11-0236-0420 3/4” 24 15,8 32 10 0,12 11-0236-0525 1” 28 18,0 41 10 0,22 11-0236-06

Design


DN Dim. L ISO 228/1 NW Mpa kg/pce EN 1.4404

Threaded Fittings

Threaded Fittings

85


25 1” 27 14,0 39,5 20 10,0 0,15 11-0237-0632 1 1/4” 33 19,0 49,5 22 6,4 0,30 11-0237-07 40 1 1/2” 35 20,5 59,0 25 6,4 0,42 11-0237-0850 2” 36 21,0 70,0 30 6,4 0,66 11-0237-0965 2 1/2” 42 25,0 88,0 40 4,0 1,23 11-0237-1080 3” 42 25,0 100,0 45 4,0 1,65 11-0237-11

Design


DN Dim. L ISO 228/1 D NW Mpa kg/pce EN 1.4404


6 1/8” 16 6 7 10,0 0,01 11-0238-018 1/4” 18 9 9 10,0 0,02 11-0238-0210 3/8” 20 9 10 10,0 0,03 11-0238-0315 1/2” 22 12 11 10,0 0,04 11-0238-0420 3/4” 27 13 16 10,0 0,09 11-0238-0525 1” 32 15 19 10,0 0,16 11-0238-0632 1 1/4” 36 17 22 6,4 0,29 11-0238-0740 1 1/2” 37 17 22 6,4 0,39 11-0238-0850 2” 43 22 27 6,4 0,69 11-0238-0965 2 1/2” 46 24 32 4,0 1,17 11-0238-1080 3” 50 27 36 4,0 1,74 11-0238-11

Design



OT-No.: 804R-231 Hexagonal caps

6 1/8” 13 9,5 14 10,0 0,01 11-0231-018 1/4” 17 13,5 19 10,0 0,01 11-0231-0210 3/8” 18 14,5 22 10,0 0,03 11-0231-0315 1/2” 22 18,5 27 10,0 0,06 11-0231-0420 3/4” 24 20,0 32 10,0 0,08 11-0231-0525 1” 28 23,5 41 10,0 0,11 11-0231-0632 1 1/4” 30 25,0 50 6,4 0,24 11-0231-0740 1 1/2” 31 25,5 55 6,4 0,25 11-0231-0850 2” 35 28,0 70 6,4 0,52 11-0231-0965 2 1/2” 40 33,0 85 4,0 0,74 11-0231-1080 3” 45 38,0 95 4,0 0,86 11-0231-11100 4” 45 38,0 126 4,0 1,74 11-0231-12

86

Design



OT-No.: 804R-232 Round caps

6 1/8” 13 9,5 14,5 10,0 0,02 11-0232-018 1/4” 17 13,5 18,0 10,0 0,03 11-0232-0210 3/8” 18 14,0 21,5 10,0 0,03 11-0232-0315 1/2” 22 18,0 27,0 10,0 0,05 11-0232-0420 3/4” 24 19,5 33,5 10,0 0,09 11-0232-0525 1” 28 23,0 39,5 10,0 0,14 11-0232-0632 1 1/4” 31 25,5 50,0 6,4 0,22 11-0232-0740 1 1/2” 31 25,5 57,0 6,4 0,28 11-0232-0850 2” 37 30,0 69,5 6,4 0,48 11-0232-0965 2 1/2” 42 34,5 84,5 4,0 0,75 11-0232-1080 3” 46 38,0 100,0 4,0 1,13 11-0232-11

Design


DN Dim. L ISO 228/1 D Mpa kg/pce EN 1.4404

Threaded Fittings

87

Round nutsR-216PAGE 88

Hexagonal nutsR-217PAGE 88

Claw couplingsR-140PAGE 89

Hose nipplesR-141PAGE 89




Double hose nipplesR-146PAGE 90

TeesR-221PAGE 91

ElbowsR-222PAGE 91

Bends 45°R-225PAGE 92

Bends 90°R-226PAGE 92

Threaded Fittings

88

Threaded Fittings

OT-No.: 805R-216 Round nuts

6 1/8” 9 14,0 10,0 0,01 11-0216-018 1/4” 10 18,5 10,0 0,02 11-0216-0210 3/8” 10 21,5 10,0 0,02 11-0216-0315 1/2” 12 26,5 10,0 0,03 11-0216-0420 3/4” 13 32,5 10,0 0,04 11-0216-0525 1” 15 40,0 10,0 0,05 11-0216-0632 1 1/4” 17 48,3 6,4 0,10 11-0216-0740 1 1/2” 18 54,5 6,4 0,11 11-0216-0850 2” 19 66,3 6,4 0,15 11-0216-0965 2 1/2” 23 82,0 4,0 0,26 11-0216-1080 3” 25 95,0 4,0 0,35 11-0216-11

Design


DN Dim. ISO 228/1 D Mpa kg/pce EN 1.4404

OT-No.: 805R-217 Hexagonal nuts

6 1/8” 7 17 10,0 0,01 11-0217-018 1/4” 8 22 10,0 0,02 11-0217-2210 3/8” 9 27 10,0 0,03 11-0217-2315 1/2” 9 32 10,0 0,04 11-0217-2420 3/4” 10 36 10,0 0,05 11-0217-2525 1” 11 46 10,0 0,08 11-0217-2632 1 1/4” 13 55 6,4 0,13 11-0217-0740 1 1/2” 13 60 6,4 0,13 11-0217-0850 2” 14 75 6,4 0,22 11-0217-0965 2 1/2” 16 95 4,0 0,40 11-0217-1080 3” 19 105 4,0 0,48 11-0217-11

Design


DN Dim. ISO 228/1 NW Mpa kg/pce EN 1.4404

Threaded Fittings

OT-No.: 822R-140 Claw couplings

10 3/8” 109 15 20 10,5 8 10 0,37 11-0140-0315 1/2” 109 15 20 14,6 10 10 0,38 11-0140-0420 3/4” 109 15 30 20,5 15 10 0,40 11-0140-05

89

Design


DN Dim. L ISO7/1 L2 D d Mpa kg/pce EN 1.4408

OT-No.: 822R-141 Hose nipples

8 1/4” 70 32 13,5 13,3 2,3 10,0 0,04 11-0141-0210 3/8” 70 32 17,2 17,0 2,3 10,0 0,05 11-0141-0315 1/2” 70 32 21,3 20,8 2,6 10,0 0,07 11-0141-0420 3/4” 70 32 26,9 26,7 2,6 10,0 0,10 11-0141-0525 1” 70 32 33,7 33,4 3,2 10,0 0,15 11-0141-0632 1 1/4” 70 32 42,4 42,2 3,2 6,4 0,19 11-0141-0740 1 1/2” 100 32 48,3 48,0 3,2 6,4 0,33 11-0141-0850 2” 100 32 60,3 60,0 3,6 6,4 0,47 11-0141-09

Design


DN Dim. L L1 D D1 T Mpa kg/pce EN 1.4404


8 1/4” 70 32 9 13,5 13,0 2,3 10,0 0,03 11-0142-0210 3/8” 70 32 9 17,2 17,0 2,3 10,0 0,05 11-0142-0315 1/2” 70 32 12 21,3 20,8 2,6 10,0 0,07 11-0142-0420 3/4” 70 32 13 26,9 26,7 2,6 10,0 0,08 11-0142-0525 1” 70 32 15 33,7 33,4 3,2 10,0 0,12 11-0142-0632 1 1/4” 70 32 17 42,4 42,2 3,2 6,4 0,17 11-0142-0740 1 1/2” 100 32 17 48,3 48,0 3,2 6,4 0,29 11-0142-0850 2” 100 32 22 60,3 60,0 3,6 6,4 0,41 11-0142-09

Design


DN Dim. L L1 ISO 7/1 D D1 T Mpa kg/pce EN 1.4404

90

Threaded Fittings


8 1/4” 32 25 11,0 6,0 7,5 4,5 10,0 0,01 11-0143-0210 3/8” 34 25 14,0 10,0 10,5 7,0 10,0 0,01 11-0143-0315 1/2” 40 25 18,0 13,0 13,5 10,0 10,0 0,02 11-0143-0420 3/4” 40 25 23,5 18,5 20,0 15,5 10,0 0,04 11-0143-0525 1” 40 25 30,0 23,0 25,0 20,0 10,0 0,05 11-0143-0632 1 1/4” 61 35 38,0 30,0 32,0 25,0 6,4 0,14 11-0143-0740 1 1/2” 61 35 44,0 38,0 39,0 32,0 6,4 0,17 11-0143-0850 2” 83 50 55,0 47,0 50,0 42,0 6,4 0,35 11-0143-09

Design


DN Dim. L L1 D D1 D2 d Mpa kg/pce EN 1.4404


6 1/8” 36 17,5 10,0 6,5 3,5 14 10,0 0,02 11-0144-018 1/4” 40 20,0 11,0 8,5 4,5 14 10,0 0,02 11-0144-0210 3/8” 42 20,0 12,5 11,0 7,0 19 10,0 0,04 11-0144-0315 1/2” 48 25,0 15,0 14,0 10,0 22 10,0 0,06 11-0144-0420 3/4” 56 25,0 16,5 21,0 16,0 30 10,0 0,10 11-0144-0525 1” 65 35,0 19,0 26,5 21,5 36 10,0 0,16 11-0144-0632 1 1/4” 75 40,0 23,5 33,0 25,0 46 6,4 0,35 11-0144-0740 1 1/2” 78 40,0 21,5 41,0 32,0 50 6,4 0,43 11-0144-0850 2” 96 40,0 25,8 51,0 42,0 65 6,4 0,78 11-0144-09

Design


DN Dim. L L1 ISO 7/1 D d NW Mpa kg/pce EN 1.4404

OT-No.: 822R-146 Double hose nipples

8 13,5 70 32 13,3 2,3 0,03 19-0146-0210 17,2 70 32 17,0 2,3 0,04 19-0146-0315 21,3 70 32 20,8 2,6 0,06 19-0146-0420 26,9 70 32 26,7 2,6 0,08 19-0146-0525 33,7 70 32 33,4 3,2 0,13 19-0146-0632 42,4 70 32 42,2 3,2 0,16 19-0146-0740 48,3 70 32 48,0 3,2 0,26 19-0146-0850 60,3 70 32 60,0 3,6 0,37 19-0146-09

Weight Article code

DN D L L1 D1 T kg/pce EN 1.4404

Threaded Fittings

OT-No.: 806R-221 Tees

6 1/8” 38,0 12 19 14,0 10,0 0,04 11-0221-01 11-0221-518 1/4” 42,0 13 21 17,5 10,0 0,05 11-0221-02 11-0221-5210 3/8” 50,0 15 25 21,6 10,0 0,08 11-0221-03 11-0221-5315 1/2” 56,0 16 28 27,0 10,0 0,15 11-0221-04 11-0221-5420 3/4” 67,5 18 34 33,0 10,0 0,26 11-0221-05 11-0221-5525 1” 76,0 20 38 40,0 10,0 0,37 11-0221-06 11-0221-5632 1 1/4” 90,0 22 45 51,0 6,4 0,61 11-0221-07 11-0221-5740 1 1/2” 100,0 24 50 57,6 6,4 0,91 11-0221-08 11-0221-5850 2” 116,0 27 58 67,8 6,4 1,18 11-0221-09 11-0221-5965 2 1/2” 150,0 30 75 84,0 4,0 1,88 11-0221-10 _80 3” 160,0 34 80 98,0 4,0 3,37 11-0221-11 _

91

Design Article Code Article Code


DN Dim. L ISO228/1 H D Mpa kg/pce EN 1.4408 EN 1.4408

OT-No.: 806R-222 Elbows

6 1/8” 19 12 14,0 10,0 0,03 11-0222-01 11-0222-518 1/4” 21 13 17,5 10,0 0,04 11-0222-02 11-0222-5210 3/8” 25 15 21,6 10,0 0,06 11-0222-03 11-0222-5315 1/2” 28 16 27,0 10,0 0,11 11-0222-04 11-0222-5420 3/4” 34 18 33,3 10,0 0,17 11-0222-05 11-0222-5525 1” 38 20 40,0 10,0 0,29 11-0222-06 11-0222-5632 1 1/4” 45 22 51,0 6,4 0,46 11-0222-07 11-0222-5740 1 1/2” 50 24 57,6 6,4 0,52 11-0222-08 11-0222-5850 2” 58 27 68,0 6,4 0,95 11-0222-09 11-0222-5965 2 1/2” 75 30 84,0 4,0 1,57 11-0222-10 _80 3” 85 34 98,0 4,0 2,28 11-0222-11 _



DN Dim. H ISO228/1 D Mpa kg/pce EN 1.4408 EN 1.4408

92

Threaded Fittings

OT-No.: 806R-225 Bends 45°

6 1/8” 10,2 2,0 45 9 27,5 10,0 0,05 11-0225-018 1/4” 13,5 2,3 50 11 28,5 10,0 0,09 11-0225-0210 3/8” 17,2 2,3 60 12 35,0 10,0 0,14 11-0225-0315 1/2” 21,3 2,6 65 15 45,0 10,0 0,22 11-0225-0420 3/4” 26,9 2,6 85 16 57,5 10,0 0,36 11-0225-0525 1” 33,7 3,2 100 19 72,5 10,0 0,63 11-0225-0632 1 1/4” 42,4 3,2 115 21 92,5 6,4 0,94 11-0225-0740 1 1/2” 48,3 3,2 135 21 107,5 6,4 1,27 11-0225-0850 2” 60,3 3,6 160 25 135,0 6,4 2,07 11-0225-0965 2 1/2” 76,1 3,6 200 30 175,0 4,0 3,29 11-0225-1080 3” 88,9 4,0 240 33 205,0 4,0 5,00 11-0225-11

Design


DN Dim. D T H ISO7/1 Radius Mpa kg/pce EN 1.4404

OT-No.: 806R-226 Bends 90°

6 1/8” 10,2 2,0 50 9 30 10,0 0,05 11-0226-018 1/4” 13,5 2,3 60 11 30 10,0 0,10 11-0226-0210 3/8” 17,2 2,3 70 12 40 10,0 0,15 11-0226-0315 1/2” 21,3 2,6 80 15 45 10,0 0,23 11-0226-0420 3/4” 26,9 2,6 100 16 55 10,0 0,35 11-0226-0525 1” 33,7 3,2 120 19 70 10,0 0,61 11-0226-0632 1 1/4” 42,4 3,2 140 21 90 6,4 0,93 11-0226-0740 1 1/2” 48,3 3,2 160 21 100 6,4 1,18 11-0226-0850 2” 60,3 3,6 190 25 120 6,4 1,95 11-0226-0965 2 1/2” 76,1 3,6 240 30 150 4,0 3,27 11-0226-1080 3” 88,9 4,0 290 33 180 4,0 4,91 11-0226-11

Design


DN Dim. D T H ISO 7/1 Radius Mpa kg/pce EN 1.4404

93

CouplingsI-131PAGE 94

Straight socketsI-201PAGE 94

NipplesI-208PAGE 95

TeesI-221PAGE 95

ElbowsI-222PAGE 96

Threaded Fittings

Threaded Fittings

94

OT-No.: 830I-131 Couplings

10-10,2 32 8,0 8,0 15,0 10,30 8,5 24 10,0 0,06 12-0131-0112,0 38 8,0 10,0 20,5 12,10 10,0 30 10,0 0,12 12-0131-0214,0 38 10,0 10,0 20,5 14,10 12,0 30 10,0 0,11 12-0131-0317-17,2 41 10,0 10,0 24,0 17,40 15,0 38 10,0 0,17 12-0131-0420,0 46 10,0 10,0 29,0 20,20 18,0 43 10,0 0,24 12-0131-0521,3 46 10,0 10,0 29,0 21,50 19,3 43 10,0 0,24 12-0131-0626,9 50 12,7 12,7 35,0 27,10 24,0 50 10,0 0,34 12-0131-0728,0 50 12,7 12,7 35,0 28,25 25,0 50 10,0 0,33 12-0131-0833,7 56 12,7 12,7 44,0 33,70 30,5 60 6,4 0,55 12-0131-0935,0 56 12,7 12,7 44,0 35,25 32,0 60 6,4 0,53 12-0131-1042,4 62 12,7 12,7 52,0 42,70 39,5 68 6,4 0,69 12-0131-1143,0 62 12,7 12,7 52,0 43,30 40,0 68 6,4 0,70 12-0131-1248,3 64 12,7 12,7 58,0 48,60 45,3 74 6,4 0,85 12-0131-1360,3 67 16,0 16,0 71,5 60,70 57,2 88 6,4 1,17 12-0131-1476,1 73 16,0 16,0 88,0 76,50 72,1 110 6,4 1,40 12-0131-15

Design


Dim. L L1 L2 D d d1 NW Mpa kg/pce EN 1.4404

OT-No.: 831I-201 Straight sockets

10-10,2 25 8,0 13,5 10,3 2,3 10,0 0,01 12-0201-0112,0 25 10,0 16,0 12,3 3,0 10,0 0,02 12-0201-0213,5 26 10,0 18,5 13,8 3,4 10,0 0,03 12-0201-0314,0 26 10,0 18,5 14,3 3,4 10,0 0,03 12-0201-0417-17,2 26 10,0 21,5 17,5 3,1 10,0 0,03 12-0201-0520,0 30 10,0 26,5 20,3 3,8 10,0 0,07 12-0201-0721,3 30 10,0 26,5 21,6 3,8 10,0 0,05 12-0201-0826,9 35 12,7 32,0 27,2 4,1 10,0 0,06 12-0201-0928,0 35 12,7 32,0 28,3 3,8 10,0 0,07 12-0201-1033,7 38 12,7 40,0 34,0 4,4 10,0 0,12 12-0201-1135,0 38 12,7 40,0 35,3 3,8 6,4 0,10 12-0201-1242,4 38 12,7 48,3 42,7 4,5 6,4 0,10 12-0201-1343,0 38 12,7 48,3 43,3 4,2 6,4 0,14 12-0201-1448,3 38 12,7 54,5 48,8 4,7 6,4 0,20 12-0201-1560,3 47 16,0 66,3 60,8 4,7 6,4 0,32 12-0201-1676,1 47 16,0 82,0 76,6 5,0 4,0 0,30 12-0201-17

Design


Dim. L L1 D d T Mpa kg/pce EN 1.4404

Threaded Fittings

95

OT-No.: 832I-208 Nipples

6 1/8” 30 6 8,0 10,2 8,20 2,0 10,0 0,01 12-0208-018 1/4” 30 9 8,0 13,5 10,30 2,3 10,0 0,02 12-0208-028 1/4” 30 9 10,0 16,0 12,10 3,5 10,0 0,02 12-0208-0310 3/8” 30 9 10,0 17,2 14,10 2,3 10,0 0,02 12-0208-0415 1/2” 35 12 10,0 21,5 15,20 4,5 10,0 0,06 12-0208-0515 1/2” 35 12 10,0 21,5 17,40 3,1 10,0 0,06 12-0208-0620 3/4” 40 13 10,0 26,5 20,20 3,8 10,0 0,07 12-0208-0720 3/4” 40 13 12,7 26,5 21,50 3,8 10,0 0,07 12-0208-0820 3/4” 40 13 12,7 26,5 23,20 3,8 10,0 0,06 12-0208-0925 1” 40 15 12,7 35,0 25,20 6,0 10,0 0,15 12-0208-1025 1” 40 15 12,7 35,0 28,25 5,0 10,0 0,13 12-0208-1125 1” 40 15 12,7 33,7 30,25 3,2 10,0 0,13 12-0208-1232 1 1/4” 50 17 12,7 45,0 35,25 6,5 6,4 0,25 12-0208-1332 1 1/4” 50 17 12,7 42,4 38,25 3,2 6,4 0,30 12-0208-1440 1 1/2” 50 17 12,7 48,3 43,30 4,5 6,4 0,35 12-0208-1550 2” 50 22 15,7 63,0 53,30 6,5 6,4 0,37 12-0208-16

Design


DN Dim. L ISO 7/1 L2 D d T Mpa kg/pce EN 1.4404

OT-No.: 836I-221 Tees

10-10,2 38,0 10,0 14,0 10,3 8,7 19 10,0 0,03 12-0221-0112,0 42,0 10,0 17,5 12,1 11,6 21 10,0 0,06 12-0221-0213,5 42,0 10,0 17,5 13,6 11,6 21 10,0 0,05 12-0221-0314,0 42,0 10,0 17,5 14,1 11,6 21 10,0 0,05 12-0221-0417-17,2 50,0 10,0 21,6 17,4 15,2 25 10,0 0,08 12-0221-0520,0 56,0 10,0 27,0 20,2 19,0 28 10,0 0,16 12-0221-0621,3 56,0 10,0 27,0 21,5 19,0 28 10,0 0,13 12-0221-0726,9 67,5 12,7 33,0 27,2 24,4 34 10,0 0,21 12-0221-0828,0 67,5 12,7 33,0 28,3 24,4 34 10,0 0,23 12-0221-0933,7 76,0 12,7 40,0 34,0 30,2 38 10,0 0,31 12-0221-1035,0 76,0 12,7 40,0 35,3 30,2 38 6,4 0,35 12-0221-1142,4 90,0 12,7 51,0 42,7 38,7 45 6,4 0,62 12-0221-1243,0 90,0 12,7 51,0 43,3 38,7 45 6,4 0,59 12-0221-1348,3 100,0 12,7 57,0 48,6 44,4 50 6,4 0,88 12-0221-1460,3 116,0 12,7 68,0 60,5 56,3 58 6,4 1,18 12-0221-15

Design


Dim. L L1 D d d1 H Mpa kg/pce EN 1.4408

OT-No.: 836I-222 Elbows

10-10,2 10,0 14,0 10,3 8,7 19 10,0 0,02 12-0222-0112,0 10,0 17,5 12,1 11,6 21 10,0 0,04 12-0222-0213,5 10,0 17,5 13,6 11,6 21 10,0 0,03 12-0222-0314,0 10,0 17,5 14,1 11,6 21 10,0 0,04 12-0222-0417-17,2 10,0 21,6 17,4 15,2 25 10,0 0,06 12-0222-0520,0 10,0 27,0 20,2 19,0 28 10,0 0,12 12-0222-0621,3 10,0 27,0 21,5 19,0 28 10,0 0,14 12-0222-0726,9 12,7 33,0 27,2 24,4 34 10,0 0,19 12-0222-0828,0 12,7 33,0 28,3 24,4 34 10,0 0,17 12-0222-0933,7 12,7 40,0 34,0 30,2 38 10,0 0,29 12-0222-1035,0 12,7 40,0 35,3 30,2 38 6,4 0,29 12-0222-1142,4 12,7 51,0 42,7 38,7 45 6,4 0,46 12-0222-1243,0 12,7 51,0 43,3 38,7 45 6,4 0,45 12-0222-1348,3 12,7 57,0 48,6 44,4 50 6,4 0,53 12-0222-1460,3 12,7 68,0 60,5 56,3 58 6,4 0,89 12-0222-15

96

Design


Dim. L D d d1 H Mpa kg/pce EN 1.4408

Threaded Fittings

Threaded Fittings

97


98

99

Inspection and dimensional standards

Tubes and Pipes

Process pipes EN 10217-7 EN ISO 1127

EN 10296-2 SSG 1361

DIN 17455 ASME B36.19

AD 2000 W2 ASME B36.10

ASTM A 312

ASTM A 358

ASTM A 409

ASTM B 673

ASTM A 778

ASTM A 790

ASTM A 928

Process pipes HF DIN 17455 EN ISO 1127

EN 10296-2 SSG 1361

Heat Exchanger Tubes EN 10217-7 EN ISO 1127

ASTM A 249 SSG 1361

ASTM A 269 ANSI B36.19

ASTM A 789 Imperial

ASTM B 674 DIN 28180

AD 2000 W2

Hygienic pipes EN 10217-7 DIN 11850

ASTM A 270 SMS 3008

Imperial

Tapwater tubes EN 10312 EN ISO 1127

DVGW W541

Box-sections Mill standard Mill standard

Decorative EN 10296-2 EN ISO 1127

DIN 17455

Spirally welded DIN 17455 EN ISO 1127

EN 10296-2

Product Inspection Standard Dimensional Standard

100

Inspection and dimensional standards

Butt Weld Fittings

Elbows ASTM A 403 ASME B16.9

ASTM A 403 WP-S Mill std

ASTM A 815 ISO 5251

Mill std SSG 1362

EN 10253-3 EN 10253-3

EN 10253-4 EN 10253-4

Reducers ASTM A 403 ASME B16.9

ASTM A 403 WP-S ISO 5251

EN 10253-3 SSG 1364

EN 10253-4 Mill std.

SFS 4162

EN 10253-3

EN 10253-4

Tees ASTM A 403 ASME B16.9

ASTM A 403 WP-S ISO 5251

EN 10253-3 SSG1363

EN 10253-4 Mill std

EN 10253-3

EN 10253-4

Collars EN 1092-1 SFS 4167

Mill std SFS 4168

SFS 4169

SFS 4170

SSG 1366

EN 1092-1

Mill std

Weldring necks EN 1092-1 EN 1092-1

Caps EN 10253-3/4 ISO 5251

ASTM A403 WP-S ASME B16.9

SSG 1369

EN 10253-3/4

Product Inspection Standard Dimensional Standard

Tolerance

Class

Tolerance on outside diameter

D1 +/-1,5 % with +/- 0,75 mm minD2 +/-1 % with +/- 0,5 mm minD3 +/-0,75 % with +/- 0,3 mm minD4 +/-0,5 % with +/- 0,1 mm min

The tolerances on outside diameter include ovality.

Tolerance

Class

Tolerance on thickness

T1 +/-15 % with +/- 0,6 mm minT2 +/-12,5 % with +/- 0,4 mm minT3 +/-10 % with +/- 0,2 mm minT4 +/-7,5 % with +/- 0,15 mm minT5 +/-5 % with +/- 0,1 mm min

The tolerances on thickness include eccentricity.

Tolerances according to EN ISO 1127

101

Dimension standards

ISO 4200 SSG EN ISO 1127

NominalDiameter

DN

1361Tab 3-4 OD mm

Outer Diameter, mmSerie ANSI

B36.19MImperial

ODHygienic

ODHydraul

OD

1 2 3 Old NPS mm mm Inch mm mm4 6 6 6,35 1/4 66 8 9,53 3/8 88 10

1210,213,5 10 121 1/8 1/4

10,313,7 12,7 1/2 10 12

1016 17,2 16 14 14 3/8 17,1 15,88 5/8

1516

1520 21,3 19 20 18 20 1/2 21,3 19,05 3/4 18/19

1820

2025 26,9 25 22 25,4 25 3/4 26,7 25,40 1

22/2325

22 25

2530 33,7 31,8 32 30 30 1 33,4 31,75 1 1/4

28/2932

28 30

32

38 42,4 38 40 35 38 1 1/4 42,2 38,1 1 1/234/35 38

40/41 3840 43/44 48,3 44,5 44,5 1 1/2 48,3 44,5 1 3/4 5050

53/5460,3

5157

5457 2 60,3

50,8 2 5152/53

6065

76,1

63,570

2 1/2 7363,576,2

2 1/23

63,570

76,1 6580 83/84 88,9 82,5 3 88,9 88,9 3 1/2 85100 103/104

114,3101,6

1083 1/2 4

101,6114,3

101,6 114,3

44 1/2

101,6104

125 128/129139,7 133 5

127,0139,7

127,0139,7

55 1/2

129

150 154

168,3159

6 168,3

152,4

6154

102

Dimension standards

ISO 4200 SSG EN ISO 1127Nominal 1361 Outer Diameter, mm ANSIDiameter Tab 3-4 Serie B36.19M

DN OD mm 1 2 3 Old NPS mm200 204

219,1 8 219,1250 254

273267

10 273,0300 305

323,9 12 323,9350 355 355,6

36814 355,6

400 406 406,4419

16 404,6

450506/508

457 1820

457508500 508

606/6082224

559610600 610

706/7082628

660711700 711

806/8083032

762813800 813

906/9083436

864914900 914

3840

96510161000 1016

4244

10671100 1118

4648

11681200 1219

5256

13211400 1422

6064

15241600 1626

6872

17271800 1829

7680

19302000 2032

103

Stainless steel grades

Standard grades

4301 1.4301 (304) 0,04 17,0 8,5 - 2333 1.4301

4307 1.4307 304L 0,02 18,0 8,0 - (2352) (1.4306) ANSI/ISO/Metric DIN/SMS/Imp

4541 1.4541 321 0,04 17,0 9,0 - Ti 2337 1.4541 ISO

4306 1.4306 304L 0,02 18,0 10,0 - 2352 1.4306

4401 1.4401 316 0,04 16,5 10,0 2,0 (2347) (1.4401)

4404 1.4404 316L 0,02 16,5 10,0 2,0 (2348) (1.4404) ANSI/ISO/Metric DIN/SMS/Imp

4571 1.4571 316Ti 0,04 16,5 10,5 2,0 Ti 2350 1.4571 ISO/Metric

4436 1.4436 316 0,04 16,5 10,5 2,5 2343 (1.4436)

4432 1.4432 316L 0,02 16,5 10,5 2,5 2343 (1.4435) ISO/Metric

4435 1.4435 316L 0,02 17,0 12,5 2,5 2353 1.4435

4438 1.4438 317L 0,02 18,0 13,0 3,0 2367 1.4438

Typical Minimum Stock standard

Outokumpu EN ASTM C Cr Ni Mo Others SS DIN Pipe/Fittings Hygienic

Heat and creep resistant grades

4948 1.4948 304H 0,05 18,1 8,3 - 0,06 2333 1.4948

4878 1.4878 321H 0,05 17,3 9,1 - 0,01 2337 1.4878

153 MA 1.4818 S30415 0,05 18,5 9,5 1,3 0,15 2372 -

253 MA 1.4835 S30815 0,09 21,0 11,0 1,6 0,17 2368 -

4828 1.4828 - 0,04 20,0 12,0 2,0 0,04 - 1.4828

4833 1.4833 309S 0,06 22,3 12,6 - 0,08 - 1.4833

4845 1.4845 310S 0,05 25,0 20,0 - 0,04 2361 1.4845

Typical

Outokumpu EN ASTM C Cr Ni Si N SS DIN

Wet corrosion resistant grades

Duplex

LDX 2101 1.4162 S32101 0,03 21,5 1,5 0,3 0,22 - -

SAF* 2304 1.4362 S32304 0,02 23,0 4,8 0,3 0,10 2327 1.4362

2205 1.4462 S32205 0,02 22,0 5,7 3,1 0,17 2377 1.4462 ANSI

SAF* 2507 1.4410 S32750 0,02 25,0 7,0 4,0 0,27 2328 -

Austenitic

904L 1.4539 N08904 0,01 20,0 25,0 4,3 0,06 2562 1.4539

254 SMO 1.4547 S31254 0,01 20,0 18,0 6,1 0,20 2378 - ANSI

Typical Stock

Outokumpu EN ASTM C Cr Ni Mo N SS DIN Pipe

The compositions comply with EN, which not always comply exactly with the old national standards.Old SS and DIN-designations within brackets specifies a slightly higher Ni-content, that is insignificant for the corrosion resistance.

These grades are available as heatexchanger tubes in minimum quantities.For other types of tube and pipe the availability is more limited. and each inquiry will be evaluated individually.

Ferritic grade

4003 1.4003 S40977 0,02 11,0 - - - 1.4003

Typical

Outokumpu EN ASTM C Cr Mo Ti No DIN

*) SAF is a trademark which is owned by Sandvik AB.

Avalible as box sections.

104

Properties

Mechanical and physicalThe stresses are valid for welded tubes and fittings made from welded tubes or hot rolled plate.

4301 1.4301 304 210 250 520 45 210 157 127 98 250 191 157 125 16 15

4541 1.4541 321 200 240 500 40 200 176 157 125 240 208 186 156 17 15

4307 1.4307 304L 200 240 500 45 200 147 118 89 240 181 147 116 17 15

4306 1.4306 304L 200 240 500 45 200 147 118 89 240 181 147 116 17 15

4401 1.4401 316 220 260 520 45 220 177 147 115 260 211 177 144 16 15

4404 1.4404 316L 220 260 520 45 220 166 137 108 260 199 167 135 16 15

4408 1.4408 316 210 440 30 170 135 105 170 135 105 15,8 15,8

4571 1.4571 316Ti 220 260 520 40 220 185 167 135 260 213 196 164 16 15

4436 1.4436 316 220 260 530 40 220 177 147 115 260 211 177 144 16 15

4432 1.4432 316L 220 260 520 45 220 165 137 108 260 200 165 135 16 15

4435 1.4435 316L 220 260 520 45 220 165 137 108 260 200 165 135 16 15

4438 1.4438 317L 220 260 520 40 220 175 155 125 260 205 185 155 16 14

LDX 2101 1.4162 S32101 450 650 30 450 380 330 13 15

SAF*2304 1.4362 S32304 400 630 25 400 330 280 13 15

2205 1.4462 S32205 460 640 25 460 360 315 13 15

SAF*2507 1.4410 S32750 530 730 20 530 450 400 13 15

904L 1.4539 N08904 220 260 520 35 220 205 175 125 260 235 205 155 16 12

254 SMO 1.4547 S31254 300 340 650 40 300 230 190 160 340 270 225 190 16.5 14 EN–Rp1,0 100.000h EN–Rm 100.000h

N/mm2 N/mm2

600°C 700°C 800°C 900°C 600°C 700°C 800°C 900°C 20-800°C

4878 1.4878 321H 190 230 500 40 65 22 10 19 15

4845 1.4845 310S 210 250 500 35 80 18 7 3 18.5 15

153 MA 1.4818 S30415 290 330 600 40 80 26 9 3 88 35 14 5 19 15

253 MA 1.4835 S30815 310 350 650 40 80 26 11 6 88 35 15 8 19 15

Coefficient Thermal

Strength at 20°C Strength at high temperatures of linear conductivity

Designations EN min values EN min values N/mm2 expansion

Rp0,2 Rp1,0 Rm A5 Rp0,2 Rp1,0 20-100°C 20°C

Outokumpu EN ASTM N/mm2 N/mm2 N/mm2 % 20°C 100°C 200°C 400°C 20°C 100°C 200°C 400°C 10-6 .C-1 W/m°C

*) SAF is a trademark which is owned by Sandvik AB.

Minimum values for 1,0 % proof strength at elevated temperatures in the solution annealed condition.

NOTE! For steel grade EN 1.4462 (2205) is the fi gures expressed in 0,2 % proof strength.

The figures in the table refers to cold rolled strip ≤ 6 mm for pressure purposes according EN 10028-7, except EN 1.4408 which refer to steel castings for pressure purposes according EN 10213-4.

Steel

Grade

Design

temp

°C

EN 1.4436

Rp 1.0

(20°C)

= 270 N/

mm2

EN 1.4301

Rp 1.0

(20°C)

= 260 N/

mm2

EN 1.4307

Rp 1.0

(20°C)

= 250 N/

mm2

EN 1.4432

Rp 1.0

(20°C)

= 270 N/

mm2

EN 1.4404

Rp 1.0

(20°C)

= 270 N/

mm2

EN 1.4541

Rp 1.0

(20°C)

= 250 N/

mm2

EN 1.4571

Rp 1.0

(20°C)

= 270 N/

mm2

EN 1.4539

Rp 1.0

(20°C)

= 270 N/

mm2

EN 1.4408

Rp 1.0

(20°C)

= 210 N/

mm2

EN 1.4162

Rp 1.0

(20°C)

= 570 N/

mm2 *

EN 1.4462

Rp 0,2

(20°C)

= 480 N/

mm2

100 0,781 0,735 0,724 0,737 0,737 0,832 0,807 0,870 0,810 0,754 0,750150 0,707 0,661 0,648 0,670 0,670 0,784 0,763 0.814 0,729 0,684 0,698200 0,655 0,604 0,588 0,618 0,618 0,744 0,726 0.759 0,643 0,649 0,656250 0,618 0,558 0,548 0,581 0,581 0,708 0,689 0.703 0,595 0,631 0,625300 0,578 0,519 0,508 0,537 0,537 0,668 0,648 0,684 0,548350 0,555 0,496 0,484 0,515 0,515 0,644 0,626 0,611 -400 0,533 0,481 0,464 0,500 0,500 0,624 0,607 0,547 0,500450 0,522 0,469 0,448 0,481 0,481 0,608 0,592 0,537500 0,515 0,461 0,436 0,474 0,474 0,596 0,585 0,518550 0,507 0,461 0,432 0,470 0,470 0,588 0,581 0,500

Sample: OT-No.: 200 Elbow 3D dimension 60.3 x 2 in steelgrade EN 1.4307.Design pressure at 20°C is 6,8 MPa.Design pressure at 250°C is then 0,548 x 6,8 = 3,7 Mpa.*) 1.4162 (LDX 2101®) is not yet included in any EN standard. For pressure purpose PMA is used. Please contact our R&D (Avesta Research Centre) for more information.

Conversion Factors

1Pa = 0.00001 bar1kPa = 0.01 bar1Mpa = 10 bar

Material selection and design

105

Selection of a stainless steel grade

Stainless steels are used mainly due to their corrosion resistance, but also thanks to their excellent

mechanical properties, formability, weldability and appearance. There are several aspects to consi-

der at material selection before the choice finally can be decided. Earlier experience is an important

factor in order to put together a group of candidate materials. The next step is to investigate the

availability of the specified product forms, dimensions, standards, minimum quantities etc. when

the order is placed, but also the availability for future construction or maintenance. Other factors are

cost for material and construction, expected lifetime and approvals. Outokumpu offer stainless steels

and products that solve most of your corrosion problems.

Corrosion resistance.

Stainless steels are resistant thanks to the invisible passive layer consisting of chromium- and iron

oxides that forms spontaneously in contact with oxidants. With increasing amounts of Cr the

corrosion resistance increases. Molybdenum (Mo) is an alloy that is added because it has a 3.3 times

higher effect than Cr, in order to prevent pitting and crevice corrosion. Nitrogen (N) is also added

in the modern developed stainless steels, and its effect on corrosion resistance is 16 times that of Cr.

A number calculated from the Pitting Resistance Equivalent PREN indicates the pitting corrosion

resistance of an alloy. PREN = %Cr+3.3x%Mo+16x%N.

Factors influencing the corrosivity

The risk for corrosion attack on stainless steels in waters increases when following parameters

increase. For decreasing pH-values below 7 the risk for corrosion increase.

• Temperature °C

• Chloride content ppm Cl ̄

• Oxygen content ppm O2

• Chlorination ppm ClO2

• pH-value

Recommended maximum chloride contents (ppm or mg/lit) at different temperatures and normal

conditions. pH = 6-8, O2=4-8 ppm, chlorination <1 ppm.

Outokumpu Cr Mo Nitrogen PREN

Cr-Ni 18,0 – 18

Cr-Ni-Mo 17,0 2,1 23

Cr-Ni-2,5Mo 17,0 2,6 25

LDX 2101 21,5 0,3 0,22 26

SAF 2304 23,0 0,3 0,10 26

2205 22,0 3,1 0,17 35

904L 20,0 4,3 0,06 35

SAF 2507 25,0 4,0 0,27 43

254 SMO 20,0 6,1 0,20 43

Temp,°C Cr-Ni Cr-Ni-Mo904 L

2205

254 SMO

SAF 2507

20 400 1000 14500 35000

30 350 750 11500 28000

40 300 600 9500 22000

50 200 450 7500 18000

Material selection and design

106

Stainless Steels for different waters at ambient temperatures.

Drinking water 4307, 4404

Polluted water 4432, LDX 2101

Brackish water 2205

Deaerated seawater LDX 2101, 2205

Fresh seawater, offshore 254 SMO, SAF 2507

Desalination SWRO 254 SMO, SAF 2507

Design of dimension and grade

Pipe systems have to be designed according to the valid safety and design regulation. In most

European countries the Pressure Equipment Directive 97/23/EC is mandatory, and in many other

countries ASME B31.1 or B31.3 are used. The user is however free to select the dimension standard

and grade. Using pipe systems with thinner walls and or grades with higher strength makes signifi-

cant weight and cost savings. Pipe systems designed with Metric Tru-Bore® and/or ISO are lighter

compared to pipe systems designed with ANSI dimensions. By using thin walled pipe made from

any of the high strength duplex stainless steels, as substitute for the austenitic standard grades, more

cost saving is possible.

Pressure calculation tool is available at www.outokumpu.com/ostp under drop down ”Tools”.

Calculation of loss of pressure due to friction

Stainless steels are not sensitive for high water velocity. Water speeds exceeding 20 m/sec are not a

problem. The stainless surface is corrosion resistant and durable, and will remain the same through

the years. The friction coefficient can be set to 0.04 for standard pipe products, and down to 0.004

for hygienic tubes with a higher surface finish. Tools for calculation of wall thickness and the loss of

pressure is available at our website www.outokumpu.com/ostp.

Our main certifications and approvals

Outokumpu Stainless Tubular Products is proud of our reputation to be known for our reliability

and high product quality. Besides satisfied customers, the proof of this is our quality certifications.

These are our main certifications:

• All the companies in the group are approved according to PED 97/23/EC and have a qua-

lity system for the manufacturing of pressure equipment components and for manufacturing

components.

• Our Quality Systems are certified in accordance with the EN ISO 9001, Quality Management

System Standard and EN ISO 14001, Environmental Management System Standard.

• Outokumpu Stainless Tubular Products is certified according to AD2000-W0 approved by

TÜV Nord e.V.

• Outokumpu Stainless Tubular Products is approved by most of the common notified bodies.

107

Certifications and approvals

108

Email: [email protected]: www.outokumpu.com/ostp

SE-103 27 Stockholm, Sweden Head officeTelephone: +46 (0)226 810 00Fax: +46 (0)8 208 481

SE-644 21 Torshälla, Sweden Pipes & TubesTelephone: +46 (0)16 349 500 HEXFax: +46 (0)16 349 525

SE-688 29 Storfors, Sweden PipesTelephone: +46 (0)550 653 00Fax: +46 (0)550 653 03

SE-737 25 Fagersta, Sweden Hygienic TubesTelephone: +46 (0)223 451 00 Domestic Water TubesFax: +46 (0)223 100 94

SE-891 25 Örnsköldsvik, Sweden Butt Weld FittingsTelephone: +46 (0)660 577 00Fax: +46 (0)660 184 95

SE-660 60 Molkom, Sweden Butt Weld FittingsTelephone: +46 (0)553 311 00 Threaded FittingsFax: +46 (0)553 311 99 Customized Threaded Fittings Spiral Welded Tubes

Outokumpu Stainless Tubular Products Oy Ab

FI-68601 Jakobstad, Finland Pipes & TubesTelephone: +358 6 786 5111 Butt Weld FittingsFax: +358 6 786 5222

Outokumpu SAS

48 rue Decomberousse, 69100 Villeurbanne, France Sales officeTelephone: +33 (0)4 7214 1980Fax: +33 (0)4 7214 1999

Outokumpu Stainless Tubular Products BV

NL-4554 LW Westdorpe, Netherlands Sales officeTelephone: +31 115 474 650Fax: +31 115 474 605

AS Outokumpu Stainless Tubular Products

EE-117 13 Tallinn, Estonia Threaded FittingsTelephone: +372 662 80 99 Customized Threaded FittingsFax: +372 662 80 98

Outokumpu Stainless Tubular Products Ltd

Brockville, CA-Ontario K6V 5T7, Canada Butt Weld FittingsTelephone: +1 613 345 5502Fax: +1 613 345 0160Website: www.outokumpu.ca

Outokumpu Stainless, Inc. Pipe Products

Wildwood, FL 34785 USA PipesTelephone: 800-731-7473Telephone: +1 352-748-1313Fax: +1 352-748-2751

AB Örnsköldsviks Mekaniska Verkstad (ÖMV)

SE-891 28 Örnsköldsvik, Sweden Equipment,Telephone: +46 (0)660 265 600 Heat exchangersFax: +46 (0)660 265 630E-mail: [email protected]: www.omv.se

SH-Trade Oy

FI-04300 Tuusula, Finland Sales officeTelephone: +358 (0)9 274 78 10 Fax: +358 (0)9 274 78 158E-mail: [email protected]: www.sh-trade.fi

Outokumpu Stainless Tubular Products AB

Contacts

Disclaimer

Information given in this brochure may be subject to alteration without notice. Care has been taken to ensure that the contents of this publication are accurate, but Outokumpu and its subsi-diary companies do not accept responsibility for errors or for information which is found to misleading. Suggestions for or descriptions of the end use or application of products or methods of working are for information only and the company and its subsidiaries accept no liability in respect thereof. Before using products supplied or manufactured by the company, the customer should satisfy himself of their suitability. If further assistance is required, the company, which has extensive research facilities, will often be able to help.

OU

TO

KU

MP

U S

tainless T

ub

ular P

rod

ucts

1151EN

-GB

:4, 2000, ww

w.rcb2.se, Printed in Sw

eden by Edita, 2007

Oct 2

007

www.outokumpu.com/ostpwww.outokumpu.com

Outokumpu is an international stainless steel company. Our vision is to be the undisputed number one in stainless, with success based on operational excellence. Customers in a wide range of industries use our metal products, technologies and services worldwide. We are dedicated to helping our customers gain competitive advantage. Outokumpu Stainless Tubular Products manufactures and sells welded stainless steel tubes, pipes and fi ttings.



Product Catalogue2007

39390.pdf

Documents

Transcript of 39390.pdf