3.3 S-MD S en

7/28/2019 3.3 S-MD S en

1/50

11/ 2009 3.63

Product information

ApplicationsG

Stainless steel screws with sealing washers for fastening profile steel sheet to profile steelsheet or for fastening profile steel sheet to steel framing.G Fastening profile aluminium sheet to profile aluminium sheet or for fastening profile alumi-

nium sheet to steel framing.G Screws without sealing washers for framing fastenings (not exposed to weather).

Product description

The screw is made from two different materials:

Stainless steel (part B) and hardened carbon steel (part A)

The drill point and thread start are made from hardened carbon steel. This

ensures trouble-free screw fastening even in the hardest construction steel.

The screw first drills the required hole in the part to be fastened and in

the framing (A). Then the thread is cut (B).

A watertight seal is formed at the fastening when the screw with sealing washer is driven.

The surface of the screw is galvanized. This protects the screw from corrosion and lubricates

the drilling and thread-cutting operation.

Several screw programs have been awarded approval by the public building

inspection authorities in Germany.

Please note the approval mark shown for each of the applicable screw programs.

All screws can be ordered with coloured heads and washers in colours according to the RAL

colour chart.

Screw designations

e.g.: S-MD 51 S 5.5x45 S for screw fastening

M for metal construction

D for self-drilling screw

5 2 pressed-on steel flange 15 mm

4 sealing washer 14 mm




0 without sealing washer1 1 drill point # 1 = 1.25 to 4 mm drilling thickness

3 drill point # 3 = 2.1 to 6 mm drilling thickness

5 drill point # 5 = 4.6 to 12 mm drilling thickness

Please refer to the screw program for the specific max.

drilling thickness for each screw.

S stainless steel 1.4301 (S for stainless steel)

5.5x45 screw dimensions ( x length)

Further designations:

S-MD51Z 4.8x 19 PB15 PB15 screw head in the colours listed in the RAL colour chartS-MD51LS 5.5x25 L extended drill point

S-MD01Z 4.8x 19 M M collated

Z-14.1-4

Hilti

MPANRW

Stainless steel self-drilling screws

7/28/2019 3.3 S-MD S en

2/50

S-MD51S / S-MD61S

3.64 11/ 2009

S-MD51S 4.8L + 5.5L/S-MD61S 4.8Lstainless steel self-drilling screw

General information

Material specification:

with hardened carbon steel drill point and

thread start, reduced-diameter drill point for

higher pull-out values and fitted EPDM

sealing washer 16 or 19 mm.

Coloured screws available on request.

Product data

ApprovalsZ-14.1-4

Hilti

MPANRW

SW L

DC

dHS

MF

mm

Dimensions

Uses:

Fastening sheet metal to sheet metal, with or without intermediate insulation layer.

For corrosion-resistant and watertight joints.

Fastening tools

Screwdriver: Hilti ST2500,

Hilti ST1800

Drive using depth

gauge set: Item no. 304611

Nut set driver

S-NSD 8: Item no. 308901

Applications

Examples

7/28/2019 3.3 S-MD S en

3/50

11/ 2009 3.65

S-MD51S 4.8 / S-MD61S 4.8

Design data

Load data

Drilling capacityt

max. 2,0 mm

Tightening torque (Recommendation)

Screw in end-stop oriented

Tightening torque: 5 Nm

Component II steel with tll [mm]

S235J according to DIN EN 10025-2S280GD or S320GD (DIN EN 10326)

0.63 0.75 0.88 1.00 1.13 1.25

Component I

steel with tl [mm]

S280GD or S320GD

(DIN EN 10326) Shear force VR,k [kN]

0.63 1.00 1.50 1.80 2.00 a 2.00 a 2.00 a

0.75 1.00 1.80 2.10 2.40 2.40 a 2.40 a

0.88 1.20 1.90 2.30 2.80 2.80

1.00 1.40 2.10 2.60 3.10

1.13 1.40 2.10 2.60

1.25 1.40 2.10

Tension force NR,k [kN]

0.50 0.43 0.54 0.65 0.76 a 0.92 a 1.08 a

0.55 0.55 0,68 0.82 0.95 a 1.16 a 1.36 a

0.63 0.80 1.00 1.20 1.40 a 1.70 a 2.00 a

0.75 0.80 1.00 1.20 1.40 1.70 a 2.00 a

0.88 0.80 1.00 1.20 1.40 1.70

1.00 0.80 1.00 1.20 1.40

1.13 0.80 1.00 1.20

1.25 0.80 1.00

Additional provisions: For steel grade S320GD characteristic loads can be increa-

sed by 8%.

7/28/2019 3.3 S-MD S en

4/50

S-MD51S 4.8 / S-MD61S 4.8

3.66 11 / 2009

Screw selectionScrew programDrilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm mm

1.25-2.0 6.0 4.8x22 16 8 500 S-MD51S 4.8x22 375228

1.25-2.0 9.0 4.8x25 16 8 500 S-MD51S 4.8x25 375229

1.25-2.0 6.0 4.8x22 19 8 500 S-MD61S 4.8x22 283052

Safety factors according to EN 1993-1-3 and CUAP 06.02/07

Tension Shear

Partial safety concept

Partial safety factor M = 1.33 M = 1.33

Influence of cyclic loading cyclic = 1.0 /

Design load NRd = 1.0 NRk/ 1.33 VRd = VRk/ 1.33

Global safety concept

Global safety factor * GLOB = 2.0 GLOB = 2.0

Recommended load NRd = 1.0 NRk/ 2.0 VRd = VRk/ 2.0

* Note: The global safety factor of 2.0 includes a partial safety factor ofF = 1.5 for wind load. For other loads safetyfactors should be applied in accordance with the appropriate standards.

(a)single

(b)side lap

(c)end overlap

(d)side lap and end overlap

7/28/2019 3.3 S-MD S en

5/50

11 / 2009 3.67

S-MD51S 5.5

Design data

Load data

Drilling capacityt

max. 3,0 mm






0.63 0.75 0.88 1.00 1.13 1.25 1.50 2.00

Component I

steel with tl [mm]

S280GD or S320GD


0.63 1.00 1.30 1.70 2.00 2.40 2.80 ac 3.00 ac 3.00 a

0.75 1.30 1.80 2.10 2.40 2.70 3.00 3.80 3.80 a

0.88 1.30 1.80 2.10 2.70 2.70 3.00 3.80 4.50

1.00 1.30 1.80 2.40 3.00 3.00 3.00 3.80 5.20

1.13 1.30 1.80 2.40 3.40 3.40 3.40 4.40

1.25 1.40 1.80 2.80 3.80 3.90 4.10 5.00

1.50 1.40 1.80 2.80 3.80 3.90 4.70 5.00


0.50 0.38 0.49 0.59 0.76 0.92 1.03 1.24 1.24

0.55 0.48 0.61 0.75 0.95 1.16 1.30 1.57 1.57

0.63 0.70 0.90 1.10 1.40 1.70 1.90 2.30 2.30

0.75 0.70 0.90 1.10 1.40 1.70 1.90 2.50 3.30

0.88 0.70 0.90 1.10 1.40 1.70 1.90 2.50 3.70

1.00 0.70 0.90 1.10 1.40 1.70 1.90 2.50 3.70

1.13 0.70 0.90 1.10 1.40 1.70 1.90 2.50

1.25 0.70 0.90 1.10 1.40 1.70 1.90 2.50

1.50 0.70 0.90 1.10 1.40 1.70 1.90 2.50

Additional provisions: For steel grade S275J and S350GD characteristic loads can beincreased by 10%.

7/28/2019 3.3 S-MD S en

6/50

S-MD51S 5.5

3.68 11 / 2009

Screw selection

Screw programDrilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm mm

1.25-3.0 8.0 5.5x25 16 8 500 S-MD51S 5.5x25 378257

1.25-3.0 15.0 5.5x32 16 8 250 S-MD51S 5.5x32 375230

1.25-3.0 21.0 5.5x38 16 8 250 S-MD51S 5.5x38 375231

1.25-3.0 33.0 5.5x50 16 8 250 S-MD51S 5.5x50 375232

(a)single

(b)side lap

(c)end overlap



Tension Shear









7/28/2019 3.3 S-MD S en

7/50

11 / 2009 3.69

S-MD51LS / S-MD61LS /S-MD71LS

S-MD51LS 5.5L/S-MD61LS 5.5L/S-MD71LS5.5L stainless steel self-drilling screw

General information



thread start, with fitted EPDM sealing

washer 16, 19 or 22 mm.


Product data

Approvals:Z-14.1-4

Hilti

MPANRW

H

L

DC

d

MFSW

mm

S

Dimensions

Uses:

Fastening trapezoidal metal sheets to liner trays.


Fastening tools:


Hilti ST1800

Drive using depth


Nut set driver


Applications

Examples

7/28/2019 3.3 S-MD S en

8/50


3.70 11 / 2009

Design data

Load data

Drilling capacityt

max. 4,0 mm






20.63 20.75 20.88 21.00 21.13 21.25 21.50

Component I

steel with tl [mm]

S280GD or S320GD


0.63 2.20 2.70 2.70 2.70 2.90 3.10 3.10

0.75 2.40 3.10 3.10 3.10 3.30 3.60 3.60

0.88 2.70 3.10 3.10 3.10 3.50 4.00 4.00

1.00 3.10 3.20 3.20 3.20 3.80 4.40 4.40

1.13 3.40 3.40 3.80 4.20 4.50 4.90

1.25 3.70 3.70 4.40 5.10 5.30 5.40

1.50 3.70 3.70 4.40 5.10 5.30 5.40


0.50 1.03 1.13 1.24 1.24 1.24 1.24 1.24

0.55 1.30 1.43 1.57 1.57 1.57 1.57 1.57

0.63 1.90 2.10 2.30 2.30 2.30 2.30 2.30

0.75 1.90 2.10 2.40 2.80 3.30 3.30 3.30

0.88 1.90 2.10 2.40 2.80 3.30 3.80 4.30

1.00 1.90 2.10 2.40 2.80 3.30 3.80 4.80

1.13 1.90 2.10 2.40 2.80 3.30 3.80

1.25 1.90 2.10 2.40 2.80 3.30 3.80

1.50 1.90 2.10 2.40 2.80 3.30 3.80

Additional provisions: For steel grade S275J and S350GD characteristic loads can beincreased by 10%.

7/28/2019 3.3 S-MD S en

9/50

11 / 2009 3.71



Tension Shear

Partial safety conceptPartial safety factor M = 1.33 M = 1.33







Screw selection

Screw programDrilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.

DC MF (dxL) AF contents designation

mm max. mm mm mm

1.8-4.0 5.0 5.5x25 16 8 500 S-MD51LS 5.5x25 378258

1.8-4.0 5.0 5.5x25 19 8 500 S-MD61LS 5.5x25 283058

1.8-4.0 5.0 5.5x25 22 8 500 S-MD71LS 5.5x25 285596

7/28/2019 3.3 S-MD S en

10/50

S-MD53S / S-MD63S /S-MD73S

3.72 11 / 2009

S-MD53S/S-MD63S/S-MD73S 5.5L +6.3L stainless steel self-drilling screw

General information






Product data

L

DC

dH

MFSW

mm

S

Dimensions

Uses:

Fastening sheet metal to steel framing, with or without intermediate insulation layers.


Fastening tools


Hilti ST1800

Drive using depth


Nut set driver


Applications

Examples

ApprovalsZ-14.1-4

Hilti

MPANRW

DCmax/MFmax

DCmin DCmin

DCmax

MFmax

without insulation with insulation

7/28/2019 3.3 S-MD S en

11/50

11 / 2009 3.73

S-MD53S 5.5

Design data

Load data

Drilling capacityt

max. 5,50 mm





S235J according to DIN EN 10025-2

S280GD or S320GD (DIN EN 10326)1.50 2.00 2.50 3.00 4.00

Component I

steel with tl [mm]

S280GD or S320GD


0.63 2.10 ac 2.60 ac 3.00 ac 3.40 ac 3.40 ac

0.75 2.50 ac 3.00 ac 3.50 ac 4.00 ac 4.00 ac

0.88 2.70 3.40 ac 4.00 ac 4.60 ac 4.60 a1.00 2.90 4.80 ac 5.00 ac 5.20 ac 5.20 a

1.13 3.30 5.10 5.40 6.00 6.00

1.25 3.60 5.30 5.80 6.80 6.80

1.50 4.40 5.90 6.60 7.20 7.20

1.75 4.40 5.90 6.60 7.20

2.00 5.40 6.50 6.60 7.20


0.50 0.92 ac 1.35 ac 1.35 ac 1.35 ac 1.35 ac0.55 1.16 ac 1.71 ac 1.71 ac 1.71 ac 1.71 ac

0.63 1.70 ac 2.50 ac 2.50 ac 2.50 ac 2.50 ac

0.75 1.70 ac 2.60 ac 3.30 ac 3.30 ac 3.30 ac

0.88 1.70 2.60 ac 3.60 ac 4.10 ac 4.10 a

1.00 1.70 2.60 ac 3.60 ac 4.60 ac 4.70 a

1.13 1.70 2.60 3.60 4.60 5.40

1.25 1.70 2.60 3.60 4.60 5.90

1.50 1.70 2.60 3.60 4.60 6.001.75 1.70 2.60 3.60 4.60

2.00 1.70 2.60 3.60 4.60

7/28/2019 3.3 S-MD S en

12/50

S-MD53S 5.5

3.74 11 / 2009

(a)single

(b)side lap

(c)end overlap


Additional provisions: For steel grade S275J and S350GD characteristic loads can be

increased by 10%.


Tension Shear








* Note: The global safety factor of 2.0 includes a partial safety factor ofF = 1.5 for wind load. For other loads safety

factors should be applied in accordance with the appropriate standards.

7/28/2019 3.3 S-MD S en

13/50

11 / 2009 3.75

S-MD53S 6.3

Design data

Load data

Drilling capacityt

max. 6,00 mm






S280GD or S320GD (DIN EN 10326)1.50 2.00 2.50 3.00 4.00

Component I

steel with tl [mm]

S280GD or S320GD


0.63 2.20 2.50 ac 2.80 ac 3.00 ac 2.00 ac

0.75 2.70 3.20 ac 3.60 ac 4.10 ac 4.10 ac

0.88 3.00 3.70 ac 4.50 ac 5.30 ac 5.30 ac1.00 3.30 4.00 ac 5.20 ac 6.40 ac 6.40 ac

1.13 3.70 4.70 5.70 6.70 6.70

1.25 4.10 5.10 6.00 6.90 6.90

1.50 5.00 6.30 6.90 7.50 8.10

1.75 5.00 6.30 6.90 7.50 8.10

2.00 6.70 6.70 6.90 7.50 8.10


0.50 0.76 1.46 ac 1.62 ac 1.62 ac 1.62 ac0.55 0.95 1.84 ac 2.05 ac 2.05 ac 2.05 ac

0.63 1.40 2.70 ac 3.00 ac 3.00 ac 3.00 ac

0.75 1.40 2.70 ac 3.90 ac 3.90 ac 3.90 ac

0.88 1.40 2.70 ac 4.00 ac 4.80 ac 4.80 ac

1.00 1.40 2.70 ac 4.00 ac 5.40 ac 5.60 ac

1.13 1.40 2.70 4.00 5.40 6.20

1.25 1.40 2.70 4.00 5.40 6.80

1.50 1.40 2.70 4.00 5.40 7.201.75 1.40 2.70 4.00 5.40 7.20

2.00 1.40 2.70 4.00 5.40 7.20

7/28/2019 3.3 S-MD S en

14/50


3.76 11 / 2009

(a)single

(b)side lap

(c)end overlap


Additional provisions: For steel grade S275J and S350GD characteristic loads can be

increased by 10%.


Tension Shear








7/28/2019 3.3 S-MD S en

15/50

11 / 2009 3.77


Screw selection

Screw program

Drilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm mm

2.1-5.5 8 5.5x25 16 8 500 S-MD53S 5.5x25 375233

2.1-5.5 15 5.5x32 16 8 250 S-MD53S 5.5x32 375234

2.1-5.5 21 5.5x38 16 8 250 S-MD53S 5.5x38 375235

2.1-5.5 33 5.5x50 16 8 250 S-MD53S 5.5x50 375236

2.1-5.5 46 5.5x63 16 8 100 S-MD53S 5.5x63 375237

2.1-5.5 8 5.5x25 19 8 500 S-MD63S 5.5x25 2830592.1-5.5 15 5.5x32 19 8 250 S-MD63S 5.5x32 283060

2.1-5.5 21 5.5x38 19 8 250 S-MD63S 5.5x38 283061

2.1-5.5 33 5.5x50 19 8 250 S-MD63S 5.5x50 283062

2.1-5.5 46 5.5x63 19 8 100 S-MD63S 5.5x63 283063

2.1-5.5 8 5.5x25 22 8 500 S-MD73S 5.5x25 285597

2.1-5.5 15 5.5x32 22 8 250 S-MD73S 5.5x32 285598

2.1-5.5 21 5.5x38 22 8 250 S-MD73S 5.5x38 285599

2.1-5.5 33 5.5x50 22 8 250 S-MD73S 5.5x50 285600

2.1-5.5 46 5.5x63 22 8 100 S-MD73S 5.5x63 285601

2.1-6.0 7 6.3x25 16 8 500 S-MD53S 6.3x25 375238

2.1-6.0 7 6.3x25 19 8 500 S-MD63S 6.3x25 283064

2.1-6.0 7 6.3x25 22 8 500 S-MD73S 6.3x25 285602

7/28/2019 3.3 S-MD S en

16/50

S-MD43S

3.78 11 / 2009

S-MD43S 5.5L stainless steel self-drillingscrew

General information




washer 14 mm.


Product data

L

DC

dH

MFSW

mm

S

Dimensions

Uses:

Fastening sheet metal to steel framing, with or without intermediate insulation layers.


Fastening tools


Hilti ST1800

Drive using depth


Nut set driver


Applications

Examples

ApprovalsZ-14.1-4

Hilti

MPANRW

7/28/2019 3.3 S-MD S en

17/50

11 / 2009 3.79

S-MD43S 5.5

Load data

Drilling capacityt

max. 5,50 mm






S280GD or S320GD (DIN EN 10326)1.50 2.00 2.50 3.00 4.00

Component I

steel with tl [mm]

S280GD or S320GD


0.63 2.50 2.50 ac 2.60 ac 2.70 ac 2.70 ac

0.75 2.80 2.80 ac 2.80 ac 2.80 ac 3.70 ac

0.88 3.00 3.00 ac 3.00 ac 3.00 ac 3.70 a1.00 3.30 3.70 ac 4.30 ac 4.90 ac 4.90 a

1.13 3.50 3.90 4.60 5.30 5.30

1.25 3.80 4.10 4.90 5.80 5.80

1.50 3.80 5.30 5.60 5.90 6.40

1.75 3.80 5.30 5.60 5.90

2.00 5.60 5.60 5.60 5.90


0.63 1.90 2.30 2.30 2.30 2.300.75 1.90 2.50 3.20 3.20 3.20

0.88 1.90 2.50 3.30 4.10 4.10

1.00 1.90 2.50 3.30 4.20 4.90

1.13 1.90 2.50 3.30 4.20 5.60

1.25 1.90 2.50 3.30 4.20 5.60

1.50 1.90 2.50 3.30 4.20 5.60

1.75 1.90 2.50 3.30 4.20

2.00 1.90 2.50 3.30 4.20 Additional provisions: For steel grade S275J and S350GD characteristic loads

can be increased by 10%.

Design data

7/28/2019 3.3 S-MD S en

18/50

S-MD43S 5.5

3.80 11 / 2009

Screw selection

Screw programDrilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm mm

2.1-5.5 8 5.5x25 14 8 500 S-MD43S 5.5x25 378259

2.1-5.5 15 5.5x32 14 8 500 S-MD43S 5.5x32 378260

2.1-5.5 21 5.5x38 14 8 250 S-MD43S 5.5x38 378261

2.1-5.5 33 5.5x50 14 8 250 S-MD43S 5.5x50 378262

2.1-5.5 46 5.5x63 14 8 100 S-MD43S 5.5x63 378263

(a)single

(b)side lap

(c)end overlap



Tension Shear




Design load NRd = 1.0 NRk/ 1.33 VRd = VRk/ 1.33Global safety concept




7/28/2019 3.3 S-MD S en

19/50

11 / 2009 3.81


S-MD55S/S-MD65S/S-MD75S 5.5Lstainless steel self-drilling screw

General information






Product data

SW

HS

mm L

DC

d

MF

Dimensions

Uses:

Fastening sheet metal to thick, hot-rolled steel beams, with or without intermediate

insulation layers.


Fastening tools

Screwdriver: Hilti ST1800

Drive using depth


Nut set driver


Applications

Examples

ApprovalsZ-14.1-4

Hilti

MPANRW

DCmax/MFmax

DCmin DCmin

DCmax

MFmax


7/28/2019 3.3 S-MD S en

20/50


3.82 11 / 2009

Load data

Drilling capacityt

max. 12,00 mm






4.00 5.00 6.00 8.00 10.00

Component I steel with tl [mm]

S280GD or S320GD


0.63 2.70 ac 2.70 ac 2.70 abcd 2.70 abcd 2.70 abcd


0.88 3.50 ac 3.50 ac 3.50 ac 3.50 ac 3.50 ac

1.00 4.00 ac 4.00 ac 4.00 ac 4.00 ac 4.00 ac

1.13 5.00 5.00 5.00 ac 5.00 ac 5.00 ac

1.25 6.00 6.00 6.00 ac 6.00 ac 6.00 a

1.50 6.00 6.20 6.50 ac 6.50 6.50 a

1.75 6.00 6.20 6.50 6.50 6.50

2.00 6.00 6.40 6.90 6.90 6.90






0.88 4.10 ac 4.10 ac 4.10 ac 4.10 ac 4.10 ac

1.00 4.70 ac 4.70 ac 4.70 ac 4.70 ac 4.70 ac

1.13 5.40 5.40 5.40 ac 5.40 ac 5.40 ac

1.25 5.90 5.90 5.90 ac 5.90 ac 5.90 a

1.50 6.90 6.90 6.90 ac 6.90 ac 6.90 a

1.75 6.90 6.90 6.90 6.90 6.90

2.00 8.00 8.00 8.00 8.00 8.00

Additional provisions: For steel grade S275J and S350GD characteristic loads

can be increased by 10%.

Design data

7/28/2019 3.3 S-MD S en

21/50

11 / 2009 3.83


Screw selection

Screw program

Drilling thickness Fastening thickness Dimensions Sealing washer Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm mm

4.6-12 12 5.5x45 16 8 250 S-MD55S 5.5x45 375239

4.6-12 17 5.5x50 16 8 250 S-MD55S 5.5x50 375240

4.6-12 30 5.5x63 16 8 100 S-MD55S 5.5x63 375241

4.6-12 47 5.5x80 16 8 100 S-MD55S 5.5x80 375242

4.6-12 67 5.5x100 16 8 100 S-MD55S 5.5x100 375243

4.6-12 12 5.5x45 19 8 250 S-MD65S 5.5x45 2830654.6-12 17 5.5x50 19 8 250 S-MD65S 5.5x50 283066

4.6-12 30 5.5x63 19 8 100 S-MD65S 5.5x63 283067

4.6-12 47 5.5x80 19 8 100 S-MD65S 5.5x80 283068

4.6-12 67 5.5x100 19 8 100 S-MD65S 5.5x100 283069

4.6-12 12 5.5x45 22 8 250 S-MD75S 5.5x45 285603

4.6-12 17 5.5x50 22 8 250 S-MD75S 5.5x50 285604

4.6-12 30 5.5x63 22 8 100 S-MD75S 5.5x63 285605

4.6-12 47 5.5x80 22 8 100 S-MD75S 5.5x80 285606

4.6-12 67 5.5x100 22 8 100 S-MD75S 5.5x100 285607

(a)single

(b)side lap

(c)end overlap



Tension Shear




Design load NRd = 1.0 NRk/ 1.33 VRd = VRk/ 1.33Global safety concept




7/28/2019 3.3 S-MD S en

22/50


3.84 11 / 2009

S-MD01S/S-MD03S/S-MD05S stainlesssteel self-drilling screw

General Information



thread start.

Product data

H

L

MFDC

d

SW

S

Dimensions

Uses:Fastening steel sections and sheet steel to steel framing, with or without insulating material.

Fastening tools


Torque settings:

S-MD01S 4.8 3 5

S-MD01S / S-MD01LS /

S-MD03S 5.5 6 8

S-MD03S 6.3 810S-MD05S 5.5 810

Drive without depth gauge.

Cut-out controlled by torque clutch.

Nut set driver S-NSD 8: Item no. 308901

DCmax/MFmax

DCmin DCmin

DCmax

MFmax


7/28/2019 3.3 S-MD S en

23/50

11 / 2009 3.85


Applications

Examples

7/28/2019 3.3 S-MD S en

24/50

S-MD01S 4.8

3.86 11 / 2009

Design data

Load data

Drilling capacityt

max. 2.00 mm


S280GD or S320GD (DIN EN 10326

0.63 0.75 0.88 1.00 1.13 1.25


S280GD or S320GD


0.63 0.90 0.90 0.90 0.90 0.90 0.90

0.75 0.90 1.60 1.60 1.60

0.88 0.90 1.60 2.20 2.20

1.00 0.90 1.60 2.20 2.80

1.13 0.90 1.60 2.20 2.80

1.25 0.90 1.60


0.63 0.80 0.80 0.80 0.80 0.80 0.80

0.75 1.00 1.00 1.00 1.00 1.00 1.00

0.88 1.00 1.00 1.00 1.00 1.00 1.00

1.00 1.10 1.40 1.40 1.40 1.40 1.40

1.13 1.10 1.40 1.40 1.40 1.40 1.40

1.25 1.10 1.80 1.80 2.00 2.00 2.00

7/28/2019 3.3 S-MD S en

25/50

11 / 2009 3.87

S-MD01LS 5.5

Design data

Load data

Drilling capacityt

max. 4,00 mm



20.63 20.75 20.88 21.00 21.13 21.25 21.50


S280GD or S320GD


0.63 2.10 2.10 2.10 2.10

0.75 2.10 3.00 3.00 3.00

0.88 2.10 3.00 3.10 3.10

1.00 2.10 3.00 3.10 3.20

1.13 2.10 3.00 3.10

1.25 2.10 3.00

1.50 2.10


0.63 1.60 1.60 1.60 1.60 1.60 1.60 1.60

0.75 2.00 2.00 2.00 2.00 2.00 2.00 2.00

0.88 2.00 2.00 2.00 2.00 2.00 2.00 2.00

1.00 2.00 2.20 2.20 3.10 3.10 3.10 3.10

1.13 2.00 2.20 2.20 3.10 3.10 3.10 3.10

1.25 2.00 2.20 2.20 3.10 3.10 4.30 4.30

1.50 2.00 2.20 2.20 3.10 3.10 4.30 4.80

7/28/2019 3.3 S-MD S en

26/50

S-MD03S 5.5

3.88 11 / 2009

Design data

Load data

Drilling capacityt

max. 5.50 mm



1.50 2.00 3.00


S280GD or S320GD


0.63 2.30 2.30

0.75 2.30 3.00

0.88 2.30 3.00

1.00 4.80


0.63 1.50 1.50 1.50

0.75 1.70 2.00 2.00

0.88 1.70 2.00 2.00

1.00 1.70 2.60 3.20

1.13 1.70 2.60 3.20

1.25 1.70 2.60 4.60

1.50 1.70 2.60 4.60

2.00 1.70 2.60 4.60

7/28/2019 3.3 S-MD S en

27/50

11 / 2009 3.89

S-MD03S 6.3

Design data

Load data

Drilling capacityt

max. 6.00 mm



1.50 2.00 3.00


S280GD or S320GD


0.63 2.40 2.40

0.75 2.40 3.50

0.88 2.40 3.50

1.00 3.90


0.63 1.40 1.70 1.70

0.75 1.40 2.20 2.20

0.88 1.40 2.20 2.20

1.00 1.40 2.70 3.70

1.13 1.40 2.70 3.70

1.25 1.40 2.70 5.40

1.50 1.40 2.70 5.40

2.00 1.40 2.70 5.40

7/28/2019 3.3 S-MD S en

28/50

S-MD05S 5.5

3.90 11 / 2009

Design data

Load data

Drilling capacityt

max. 12.00 mm



4.00 6.00 8.00


S280GD or S320GD


0.75 4.10 4.10 4.10

0.88 4.80 4.80 4.80

1.00 5.40 5.40 5.40

1.13 5.40 5.40 5.40

1.25 6.70 6.70 6.70


0.63 1.40 1.40 1.40

0.75 1.60 1.60 1.60

0.88 1.60 1.60 1.60

1.00 2.20 2.20 2.20

1.13 2.20 2.20 2.20

1.25 2.70 2.70 2.70

1.50 3.30 3.30 3.30

2.00 4.30 4.30 4.30

7/28/2019 3.3 S-MD S en

29/50

11 / 2009 3.91


Screw programDrilling thickness Fastening thickness Dimensions Head size Package Ordering Item no.DC MF (dxL) AF contents designation

mm max. mm mm

1.25-2.0 9 4.8x22 8 500 S-MD01S 4.8x22 285608

1.8-4 8 5.5x25 8 500 S-MD01LS 5.5x25 285609

2.1-5.5 11 5.5x25 8 500 S-MD03S 5.5x25 285610

2.1-5.5 18 5.5x32 8 250 S-MD03S 5.5x32 285611

2.1-5.5 24 5.5x38 8 250 S-MD03S 5.5x38 285612

2.1-5.5 36 5.5x50 8 250 S-MD03S 5.5x50 285613

2.1-5.5 49 5.5x63 8 100 S-MD03S 5.5x63 285614

2.1-6.0 10 6.3x25 8 500 S-MD03 S 6.3x25 285615

4.6-12 15 5.5x45 8 250 S-MD05S 5.5x45 285616

4.6-12 20 5.5x50 8 250 S-MD05S 5.5x50 285617

4.6-12 33 5.5x63 8 100 S-MD05S 5.5x63 285618

4.6-12 50 5.5x80 8 100 S-MD05S 5.5x80 285619

4.6-12 70 5.5x100 8 100 S-MD05S 5.5x100 285620


Tension Shear








7/28/2019 3.3 S-MD S en

30/50

S-MD31PS 4.8

3.92 11 / 2009

S-MD31PS 4.819 stainless steelself-drilling screw

General information



thread start, with reduced drill point

= greater pull-out value, with fitted EPDM

sealing washer 12 mm.


Product data

d

D

L

DC

MF

Dimensions

Uses:

Fastening profiled corrugated sheet metal with profiled corrugate sheet metal with or without

intermediate insulation layers.For corrosion-resistant and watertight joints.

Fastening tools:


Hilti ST2500

Drive using depth


Bit S-B TX25W: Item no. 237296

Approvals:Z-14.1-4

Hilti

MPANRW

Applications

Examples

7/28/2019 3.3 S-MD S en

31/50

11 / 2009 3.93

S-MD31PS 4.8

Design data

Load data

Drilling capacityt

max. 2.75 mm



S235 (DIN EN 10025-1)

S280GD, S320GD or S350GD (DIN EN 10326)

0.63 0.75 0.88 1.00 1.13 1.25 1.50 1.75 2.00

Component I

steel with tl [mm]

S280GD up to S350GD


0.63 1.12 1.12 1.12 1.12 1.12 1.12 1.12 1.12 1.12

0.75 1.12 1.31 1.31 1.31 1.31 1.31 1.31 1.31 1.31

0.88 1.12 1.31 1.92 1.92 1.92 1.92 1.92 1.92

1.00 1.12 1.31 1.92 2.53 2.53 2.53 2.53 2.53

1.13 1.12 1.31 1.92 2.53 2.53 2.53 2.53

1.25 1.12 1.31 1.92 2.53 2.53 2.53 2.53

1.50 1.12 1.31 1.92 2.53 2.53 2.53

1.75 1.12 1.31 1.92 2.53

2.00 1.12 1.31


0.63 0.59 0.87 1.12 1.37 1.37 1.37 1.37 1.37 1.37

0.75 0.59 0.87 1.12 1.37 1.37 1.37 1.37 1.37 1.37

0.88 0.59 0.87 1.12 1.37 1.37 1.37 1.37 1.37

1.00 0.59 0.87 1.12 1.37 1.37 1.37 1.37 1.37

1.13 0.59 0.87 1.12 1.37 1.37 1.37 1.37 1.37

1.25 0.59 0.87 1.12 1.37 1.37 1.37 1.37

1.50 0.59 0.87 1.12 1.37 1.37 1.37

1.75 0.59 0.87 1.12 1.37

2.00 0.59 0.87

7/28/2019 3.3 S-MD S en

32/50

S-MD31PS 4.8

3.94 11 / 2009

Component II

Solid timber S10/C24 with e 20 mm

end stop orientedComponent I

steel with tl [mm]

S280GD up to S350GD

(DIN EN 10326 0.63 0.75 0.88 1.00 1.13 1.25 1.50 1.75 2.00

Failure of component I Shear force VR,k [kN]

(bearing stress) 1.36 2.22 2.22 2.22 2.22 2.22 2.22 2.22 2.22

Failure of component I Tension force NR,k [kN]

(pull-over) 2.34 2.34 2.34 2.34 2.34 2.34 2.34 2.34 2.34

Addition provisions: Calculating the resistance of the screw in timber

(Component II) according to timber standard's

7/28/2019 3.3 S-MD S en

33/50

11 / 2009 3.95

S-MD31PS 4.8

Drilling capacityt

max. 2.75 mm


Component II aluminium tll [mm]

Profil sheeting with Rm 185 N/mm2 according to

DIN EN 485-2:2004-09 or substructure according to

DIN 4113-1/A1:2002-09 witht z 185 N/mm

0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50

Component I

aluminium tl [mm]Profil sheeting with Rm 185 N/mm2 according to

DIN EN 485-2:2004-09 Shear force VR,k [kN]

0.50 0.31 0.31 0.31 00.31 0.31 0.31 0.31 0.31 0.31 0.31 0.31

0.60 0.31 0.42 0.42 0.42 0.42 0.42 0.42 0.42 0.42 0.42 0.42

0.70 0.31 0.42 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53 0.53

0.80 0.31 0.42 0.53 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.70

0.90 0.31 0.42 0.53 0.70 0.88 0.88 0.88 0.88 0.88 0.88 0.88

1.00 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05 1.05 1.05 1.05

1.10 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05 1.05 1.05 1.05

1.20 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05 1.05 1.05 1.05

1.30 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05 1.05 1.05

1.40 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05 1.05

1.50 0.31 0.42 0.53 0.70 0.88 1.05 1.05 1.05


0.50 0.17 0.26 0.35 0.46 0.55 0.61 0.61 0.61 0.61 0.61 0.61

0.60 0.17 0.26 0.35 0.46 0.55 0.61 0.70 0.70 0.70 0.70 0.70

0.70 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.83 0.83 0.83

0.80 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 0.99 0.99

0.90 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 1.00 1.05

1.00 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 1.00 1.05

1.10 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 1.00 1.05

1.20 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 1.00 1.05

1.30 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91 1.00

1.40 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82 0.91

1.50 0.17 0.26 0.35 0.46 0.55 0.61 0.73 0.82

7/28/2019 3.3 S-MD S en

34/50

S-MD31PS 4.8

3.96 11 / 2009

Addition provisions: For asymmetric loading on profile sheeting with tI < 1.25 mm or

asymmetric seel profiles with tll < 5.0 mm (load values have to be

multiplied by a factor of 0.7).

Component II

Solid timber S10/C24 with e 20 mm

end stop oriented

Component I

aluminium tl [mm]


DIN EN 485-2:2004-09 0.50 0.60 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50

Failure of component I Shear force VR,k [kN]

(bearing stress) 0.79 0.93 1.06 1.28 1.49 1.71 1.71 1.71 1.71 1.71 1.71

Failure of component I Tension force NR,k [kN]

(pull-over) 0.61 0.70 0.83 0.99 1.19 1.42 1.70 2.02 2.02 2.02 2.02

Addition provisions: Calculating the resistance of the screw in timber

(Component II) according to timber standard's

Screw selection

Screw programDrilling thickness Fastening thickness Dimensions Sealing washer Drive Package Ordering Item no.DC MF (dxL) dimensions contents designation

mm max. mm mm mm

1.002.75 5 4.8x19 12 TX 25 500 S-MD 31PS 4.8x19 202421

Fastening to wood

1.002.75 4.8x38 12 TX25 250 S-MD31PS 4.8x38 387248

1.002.75 4.8x50 12 TX25 250 S-MD31PS 4.8x50 202422


Tension Shear









7/28/2019 3.3 S-MD S en

35/50

11 / 2009 3.97

S-MD31PS 5.5

S-MD31PS 5.5 stainless steelself-drilling screw

General information



thread start, with reduced drill point

= greater pull-out value, with fitted EPDM

sealing washer 12 mm.


Product data

Dimensions

Uses:

Fastening profiled corrugated sheet metal with profiled corrugate sheet metal with or without

intermediate insulation layers.For corrosion-resistant and watertight joints.

Fastening tools:


Hilti ST2500

Drive using depth



Approvals:Z-14.1-4

Hilti

MPANRW

Applications

Examples

d

D

L

DC

MF

7/28/2019 3.3 S-MD S en

36/50

S-MD31PS 5.5

3.98 11 / 2009

Design data

Load data

Drilling capacityt

max. 3.0 mm



S235 (DIN EN 10025-1)

S280GD up to S350GD (DIN EN 10326)

0.63 0.75 0.88 1.00 1.13 1.25 1.50 1.75

Component I

steel with tl [mm]

S280GD up to S350GD


0.63 1.13 1.38 1.38 1.38 1.38 1.38 1.38 1.38

0.75 1.21 1.74 1.74 1.74 1.74 1.74 1.74 1.74

0.88 1.21 1.74 2.19 2.19 2.19 2.19 2.19 2.19

1.00 1.21 1.74 2.19 2.63 2.63 2.63 2.63 2.63

1.13 1.21 1.74 2.19 2.63 2.63 2.63 2.63 2.63

1.25 1.21 1.74 2.19 2.63 2.63 2.63 2.63 2.63

1.50 1.21 1.74 2.19 2.63 2.63 2.63 2.63

1.75 1.21 1.74 2.19 2.63 2.63 2.63

2.00 1.21 1.74 2.19 2.63


0.63 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

0.75 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

0.88 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

1.00 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

1.13 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

1.25 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

1.50 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

1.75 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

2.00 0.66 0.89 1.14 1.39 1.68 1.91 1.91 1.91

7/28/2019 3.3 S-MD S en

37/50

11 / 2009 3.99

S-MD31PS 5.5



S235 (DIN EN 10025-1)


0.63 0.75 0.88 1.00 1.13

Component I

steel with tl [mm]

S280GD up to S350GD


0.63 2 2.04 2.04 2.04 2.04 2.04

0.75 2 2.04 2.41 2.41 2.41 0.88 2 2.04 2.41 2.41 2.41

1.00 2 2.04 2.41 2.41 3.07

1.13 2 2.04 2.41 2.41

1.25 2 2.04 2.41


0.63 2 1.37 2.15 2.34 2.34 2.34

0.75 2 1.37 2.15 2.34 2.34 2.34

0.88 2 1.37 2.15 2.34 2.34 2.341.00 2 1.37 2.15 2.34 2.34 2.34

1.13 2 1.37 2.15 2.34

1.25 2 1.37 2.15

1.50 2 1.37

7/28/2019 3.3 S-MD S en

38/50

S-MD31PS 5.5

3.100 11 / 2009





DIN 4113-1/A1:2002-09 witht z 185 N/mm2

0.50 0.60 0.70 0.80 0.90 1.00 1.50 2.00

Component I

aluminium tl [mm]



0.50 0.35 0.48 0.60 0.60 0.60 0.60 0.60 0.60

0.60 0.37 0.48 0.60 0.60 0.60 0.60 0.60 0.60

0.70 0.39 0.50 0.60 0.60 0.60 0.60 0.60 0.60

0.80 0.39 0.50 0.60 0.60 0.60 0.60 0.60 0.60

0.90 0.39 0.50 0.60 0.60 0.60 0.60 0.60 0.60

1.00 0.39 0.50 0.60 0.60 1.00 1.20 1.20 1.20

1.10 0.39 0.50 0.60 0.60 1.00 1.20 1.20

1.20 0.39 0.50 0.60 0.60 1.00 1.20 1.20

1.30 0.39 0.50 0.60 0.60 1.00 1.20 1.20

1.40 0.39 0.50 0.60 0.60 1.00 1.20 1.20

1.50 0.39 0.50 0.60 0.60 1.00 1.20 1.20


0.50 0.23 0.31 0.39 0.53 0.61 0.61 0.61 0.61

0.60 0.23 0.31 0.39 0.53 0.64 0.69 0.70 0.70

0.70 0.23 0.31 0.39 0.53 0.64 0.69 0.83 0.83

0.80 0.23 0.31 0.39 0.53 0.64 0.69 0.99 0.99

0.90 0.23 0.31 0.39 0.53 0.64 0.69 1.19 1.19

1.00 0.23 0.31 0.39 0.53 0.64 0.69 1.25 1.25

1.10 0.23 0.31 0.39 0.53 0.64 0.69 1.25

1.20 0.23 0.31 0.39 0.53 0.64 0.69 1.25

1.30 0.23 0.31 0.39 0.53 0.64 0.69 1.25

1.40 0.23 0.31 0.39 0.53 0.64 0.69 1.25

1.50 0.23 0.31 0.39 0.53 0.64 0.69 1.25

7/28/2019 3.3 S-MD S en

39/50

11 / 2009 3.101

S-MD31PS 5.5


Component II steel tll [mm]

S235 according to DIN EN 10026-2

S280GD up to S350GD as per DIN EN 10326

2 0.63 2 20.70 2 0.80 2 1.00 2 1.13

Component I

aluminium tl [mm]

Profil sheeting with Rm

185 N/mm2 according to


0.50 0.94 0.94 0.94 0.94 0.940.60 0.94 0.94 0.94 0.94 0.94

0.70 0.94 1.21 1.21 1.21 1.21

0.80 0.94 1.21 1.21 1.21

0.90 0.94 1.21 1.21 1.21

1.00 0.94 1.21 1.21 1.21

1.10 0.94 1.21 1.21

1.20 0.94 1.21 1.21

1.30 0.94 1.21

1.40 0.94 1.21

1.50 0.94 1.21


0.50 0.61 0.61 0.61 0.61 0.61

0.60 0.70 0.70 0.70 0.70 0.70

0.70 0.83 0.83 0.83 0.83 0.83

0.80 0.99 0.99 0.99 0.99

0.90 1.19 1.19 1.19 1.19

1.00 1.37 1.42 1.42 1.42

1.10 1.37 1.70 1.70

1.20 1.37 2.02 2.02

1.30 1.37 2.02

1.40 1.37 2.02

1.50 1.37 2.02

Addition provisions:: For asymmetric loading on profile sheeting with tl < 1.25 mm

or asymmetric seel profiles with tll < 5.0 mm (load values have

to be multiplied by a factor of 0.7).

7/28/2019 3.3 S-MD S en

40/50

S-MD31PS 5.5

3.102 11 / 2009

Screw selection


mm max. mm mm mm

1.03.00 7 5.5x22 12 TX 25 500 S-MD 31PS 5.5x22 202423

1.03.00 13 5.5x28 12 TX 25 500 S-MD 31PS 5.5x28 202424

1.03.00 23 5.5x38 12 TX 25 250 S-MD 31PS 5.5x38 2024251.03.00 35 5.5x50 12 TX 25 250 S-MD 31PS 5.5x50 202426


Tension Shear








7/28/2019 3.3 S-MD S en

41/50

11 / 2009 3.103

S-MD33PS

S-MD33PS stainless steel self-drillingscrew

General information




washer 12 mm.


Product data

d

D

L

DC MF

Dimensions

Uses:

Fastening profiled corrugated sheet metal with steel base material with or without

intermediate insulation layers.


Fastening tools:


Hilti ST2500

Drive using depth



Approvals:Z-14.1-4

Hilti

MPANRW

Applications

Examples

DCmax/MFmax

DCmin DCmin

DCmax

MFmax


7/28/2019 3.3 S-MD S en

42/50

S-MD33PS

3.104 11 / 2009

Design data

Load data

Drilling capacityt

max. 5.5 mm





DIN 4113-1/A1:2002-09 witht z 185 N/mm2

1.00 1.50 2.00 2,50 3.00

Component I

steel with tl [mm]

S280GD up to S350GD


0.63 1.10 1.10 1.10 1.10 1.10

0.75 1.28 1.46 1.46 1.46 1.46

0.88 1.32 1.73 1.73 1.73 1.73

1.00 1.36 1.99 1.99 1.99 1.99

1.13 1.36 1.99 1.99 1.99 1.99

1.25 1.36 1.99 1.99 1.99 1.99

1.50 1.36 1.99 1.99 1.99 1.99

1.75 1.36 1.99 1.99 1.99 1.99

2.00 1.36 1.99 1.99 1.99 1.99


0.63 0.34 0.78 1.17 1.66 2.34

0.75 0.34 0.78 1.17 1.66 2.34

0.88 0.34 0.78 1.17 1.66 2.34

1.00 0.34 0.78 1.17 1.66 2.34

1.13 0.34 0.78 1.17 1.66 2.34

1.25 0.34 0.78 1.17 1.66 2.34

1.50 0.34 0.78 1.17 1.66 2.34

1.75 0.34 0.78 1.17 1.66 2.34

2.00 0.34 0.78 1.17 1.66 2.34

7/28/2019 3.3 S-MD S en

43/50

11 / 2009 3.105

S-MD33PS





0.75 0.88 1.00 1.25 2 0.75 2 0.88 2 1.00 2 1.25

Component I

steel with tl [mm]

S280GD up to S350GD


0.63

0.75 1.29 1.29 1.29 1.29 2.05 2.05 2.05 2.050.88 1.29 1.81 1.81 1.81 2.05 2.56 2.56 2.56

1.00 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

1.13 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

1.25 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

1.50 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

1.75 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

2.00 1.29 1.81 2.32 2.32 2.05 2.56 3.07 3.07

Tension force NR,k [kN]0.63 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

0.75 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

0.88 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.00 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.13 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.25 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.50 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.75 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

2.00 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

7/28/2019 3.3 S-MD S en

44/50

S-MD33PS

3.106 11 / 2009

Drilling capacityt

max. 5.5 mm





DIN 4113-1/A1:2002-09 with z 185 N/mm2

1.00 1.50 2.00 2.50 3.00

Component I

aluminium tl [mm]Profil sheeting with Rm 185 N/mm2 according to


0.50 0.56 0.79 0.79 0.79 0.79

0.60 0.65 0.91 0.91 0.91 0.91

0.70 0.74 1.03 1.03 1.03 1.03

0.80 0.85 1.10 1.10 1.10 1.10

0.90 0.96 1.18 1.18 1.18 1.18

1.00 1.07 1.25 1.25 1.25 1.25

1.10 1.07 1.25 1.25 1.25 1.25

1.20 1.07 1.25 1.25 1.25 1.25

1.30 1.07 1.25 1.25 1.25 1.25

1.40 1.07 1.25 1.25 1.25 1.25

1.50 1.07 1.25 1.25 1.25 1.25


0.50 0.34 0.61 0.61 0.61 0.61

0.60 0.34 0.70 0.70 0.70 0.70

0.70 0.34 0.78 0.83 0.83 0.83

0.80 0.34 0.78 0.99 0.99 0.99

0.90 0.34 0.78 1.17 1.19 1.19

1.00 0.34 0.78 1.17 1.42 1.42

1.10 0.34 0.78 1.17 1.66 1.70

1.20 0.34 0.78 1.17 1.66 2.02

1.30 0.34 0.78 1.17 1.66 2.02

1.40 0.34 0.78 1.17 1.66 2.02

1.50 0.34 0.78 1.17 1.66 2.02

7/28/2019 3.3 S-MD S en

45/50

11 / 2009 3.107

S-MD33PS





0.75 0.88 1.00 1.25 2 0.75 2 0.88 2 1.00 2 1.25

Component I

aluminium tl [mm]




0.50 0.60

0.70 0.99 0.99 0.99 0.99 1.18 1.18 1.18 1.18

0.80 0.99 0.99 0.99 0.99 1.18 1.18 1.18 1.18

0.90 0.99 0.99 0.99 0.99 1.18 1.18 1.18 1.18

1.00 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18

1.10 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18

1.20 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18

1.30 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18

1.40 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18

1.50 0.99 0.99 1.31 1.31 1.18 1.18 1.18 1.18


0.50 0.45 0.61 0.61 0.61 0.61 0.61 0.61 0.61

0.60 0.45 0.65 0.70 0.70 0.70 0.70 0.70 0.70

0.70 0.45 0.65 0.83 0.83 0.83 0.83 0.83 0.83

0.80 0.45 0.65 0.85 0.99 0.97 0.99 0.99 0.99

0.90 0.45 0.65 0.85 1.08 0.97 1.19 1.19 1.19

1.00 0.45 0.65 0.85 1.08 0.97 1.24 1.42 1.42

1.10 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.70

1.20 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.30 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.40 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

1.50 0.45 0.65 0.85 1.08 0.97 1.24 1.51 1.91

7/28/2019 3.3 S-MD S en

46/50

S-MD33PS

3.108 11 / 2009

Screw selection


mm max. mm mm mm

2.15.5 5 5.5x22 12 TX 25 500 S-MD 33PS 5.5x22 202427

2.15.5 11 5.5x28 12 TX 25 500 S-MD 33PS 5.5x28 202428

2.15.5 21 5.5x38 12 TX 25 250 S-MD 33PS 5.5x38 2024292.15.5 33 5.5x50 12 TX 25 250 S-MD 33PS 5.5x50 202430


Tension Shear








7/28/2019 3.3 S-MD S en

47/50

11 / 2009 3.109

S-MD35PS

S-MD35PS stainless steel self-drillingscrew

General information




washer 12 mm.


Product data

L

DC

d

MFD

Dimensions

Uses:

Fastening profiled corrugated sheet metal with a thick, hot-rolled steel beams, with or

without intermediate insulation layers.


Fastening tools:


Hilti ST2500

Drive using depth



Approvals:Z-14.1-4

Hilti

MPANRW

Applications

Examples

DCmax/MFmax

DCmin DCmin

DCmax

MFmax


7/28/2019 3.3 S-MD S en

48/50

S-MD35PS

3.110 11 / 2009

Drilling capacityt

max. 12.5 mm



S235 (DIN EN 10025-1)


4.0 5.0 6.0 8.0 10.0

Component I

steel with tl [mm]

S280GD up to S350GD


0.63 2.69 2.93 3.16 3.16 3.16

0.75 2.95 3.11 3.27 3.27 3.27

0.88 3.46 3.73 4.01 4.01 4.01

1.00 3.97 4.36 4.74 4.74 4.74

1.13 4.97 5.16 5.35 5.35 5.35

1.25 5.97 5.97 5.97 5.97 5.97

1.50 5.97 6.23 6.49 6.49 6.49

1.75 5.97 6.33 6.69 6.69 6.69

2.00 5.97 6.43 6.89 6.89 6.89


0.63 2.34 2.34 2.34 2.34 2.34

0.75 2.34 2.34 2.34 2.34 2.34

0.88 2.34 2.34 2.34 2.34 2.34

1.00 2.34 2.34 2.34 2.34 2.34

1.13 2.34 2.34 2.34 2.34 2.34

1.25 2.34 2.34 2.34 2.34 2.34

1.50 2.34 2.34 2.34 2.34 2.34

1.75 2.34 2.34 2.34 2.34 2.34

2.00 2.34 2.34 2.34 2.34 2.34

Design data

Load data

7/28/2019 3.3 S-MD S en

49/50

11 / 2009 3.111

S-MD35PS



S235 (DIN EN 10025-1)


4.0 5.0 6.0 8.0 10.0

Component I

aluminium tl [mm]




0.50 1.03 1.03 1.03 1.03 1.030.60 1.27 1.27 1.27 1.27 1.27

0.70 1.51 1.51 1.51 1.51 1.51

0.80 1.79 1.79 1.79 1.79 1.79

0.90 2.07 2.07 2.07 2.07 2.07

1.00 2.35 2.35 2.35 2.35 2.35

1.10 2.35 2.35 2.35 2.35 2.35

1.20 2.35 2.35 2.35 2.35 2.35

1.30 2.35 2.35 2.35 2.35 2.35

1.40 2.35 2.35 2.35 2.35 2.35

1.50 2.35 2.35 2.35 2.35 2.35


0.50 0.61 0.61 0.61 0.61 0.61

0.60 0.70 0.70 0.70 0.70 0.70

0.70 0.83 0.83 0.83 0.83 0.83

0.80 0.99 0.99 0.99 0.99 0.99

0.90 1.19 1.19 1.19 1.19 1.19

1.00 1.42 1.42 1.42 1.42 1.42

1.10 1.70 1.70 1.70 1.70 1.70

1.20 2.02 2.02 2.02 2.02 2.02

1.30 2.02 2.02 2.02 2.02 2.02

1.40 2.02 2.02 2.02 2.02 2.02

1.50 2.02 2.02 2.02 2.02 2.02

7/28/2019 3.3 S-MD S en

50/50

S-MD35PS

Screw selection


mm max. mm mm mm

4.612 12 5.5x45 12 TX 25 250 S-MD 35PS 5.5x45 202431


Tension Shear








3.3 S-MD S en

Documents

Transcript of 3.3 S-MD S en