31-9118 part2

8/11/2019 31-9118 part2

1/31 32

6. Loosen the 2 screws that hold the icemakerassembly in place and slide it out of thefreezer compartment.

8. Unclip the light bulb sockets from theirmounting holes and disconnect the sockets.

7. Loosen the 3 screws on the icemaker bracket,and slide it out of the freezer compartment.

10. Remove the 4 hex-head screws that hold theevaporator fan shroud in place ( Fig. 1 andFig. 2).

Note: The bottom hex-head screws are hiddenunder the bottom of the evaporator fan shroud.

Top Hex-head Screws

Bottom Hex-head Screws

Auger Connector Plug

11. Unclip the auger connector plug from theevaporator fan shroud. Slide the evaporatorfan shroud down and out of the freezercompartment.

Fig. 1

Fig. 2

9. Remove the 4 hex-head screws that hold thefreezer evaporator cover in place. Carefullypull the evaporator cover out of the freezercompartment.

8/11/2019 31-9118 part2

2/31 33

Disconnect 1

Disconnect 2

12. Disconnect the fan wiring harness(Disconnect 1). Disconnect the overtemperature thermostat/light bulb wiringharness (Disconnect 2).

13. Remove the 2 hex-head screws that hold thefan bracket in place.

Screw Screw

Ground Clip

14. Remove the ground clip from the evaporatorframe.

15. Unclip the evaporator thermistor.

16. Slide the over-temperature thermostat/lightbulb wiring harness out of the fan bracket.

17. Remove the fan bracket.

Evaporator Thermistor

Note: When replacing the evaporator thermistor,cut the thermistor wires and splice the newthermistor using bell connectors. Always useRTV102 silicone to seal the end of the connectorfrom moisture.

Replacing Freezer Evaporator Using theBrazing Method

Parts Needed:Freezer Evaporator (part # WR85X10061)Drier Assembly (part # WR86X93)

Access Tube (part # WJ56X61)

Heat Shield Kit (part # WX5X8926)Caution: A heat shield kit is required for thisprocedure to prevent damage to the plasticinterior (liner) of the freezer compartment.

Note: If it is determined that the epoxy joints (thetransition joint between the aluminum and copper

jumper) on the freezer evaporator assembly aredefective, then LOKRING connectors can be usedto repair the joints. Refer to Pub. No. 31-9067 formore LOKRING information.

1. Unplug the refrigerator.2. Remove the rear access cover and evacuate

the sealed system.

3. Remove components necessary to exposethe evaporator. (See Freezer Evaporator .)

4. Remove the ice bucket, icemaker, augerassembly, fan motor housing, and fan motor.

5. Note the location of thermistor and thermostaton top of old evaporator and remove.

6. Remove heater from bottom of evaporatorand discard. Bundle remaining wires and tapehigh on the back wall of freezer.

7. Apply a liberal amount of thermal paste tosuction line where it enters the rear wall offreezer.

8. Insert the brazing shield behind the joint of theaccumulator top and suction line to protect theliner.

9. Use torch to heat the joint of the accumulatortop, separate the suction line and accumulator

top and clean the suction line surface (Fig. 1and 2).

10. Using the tubing cutter, cut fresh foodevaporator jumper (right side) tube about 2inches from the joint outlet end of the freshfood evaporator. Score and break the capillarytube about 2 inches from the end of freezerevaporator inlet jumper (left side) (Fig. 1 and2).

8/11/2019 31-9118 part2

3/31 34

11. Loosen the hex-head screws that hold theevaporator in place. Note locations of thefoam blocks at sides of old evaporator. Theseare needed for proper airow. Remove thefoam blocks and save for new evaporatorinstallation. Remove old evaporator.

Fig. 1

Fig. 2

12. Modify replacement evaporator to accept the5/16 -in. fresh food evaporator jumper.

ModifyHere

13. Install the new evaporator and tighten allmounting screws.

14. Connect tubes between top of accumulatorand suction line. Connect tubes betweenfresh food evaporator and freezer evaporator(right side). Insert the capillary tube.

15. Check that the thermal paste is still on thesuction line where it enters the rear wall of thefreezer. If not, apply paste. In addition, applythermal paste around epoxy joints on the newevaporator to prevent the heat from damaging

joint integrity.

16. Protect the freezer oor from moltensolder during brazing. Braze suction line toaccumulator on new evaporator. Angle torchso that ame is directed away from rear wallwhen brazing.

17. Move the brazing shield behind the capillary joint and braze the capillary tube.

FFEvaporator Jumper

FZEvaporator

InletJumper

Top of Accumulator

Brazing Shield

Suctio nTubeLine

CutHere

FFEvaporator

OutletRemoveScrew

CapillaryTube

CutHere

2"

Loosen Hex-Head Screws

2"

HeatHere

8/11/2019 31-9118 part2

4/31 35

18. Move the brazing shield behind the fresh food jumper to the freezer evaporator. Braze the jumper tube joint. Remove the brazing shield.Clean and inspect all joints.

19. Remove the old drier by cutting the halo loopas close as possible to the drier. Install thenew drier assembly (part # WR86X93) makingsure that there is sufcient space between the

tubing.20. Install the access tube. Clean and inspect

joints.

21. Replace the heater supplied with theevaporator. Reinstall foam blocks, thermostatand thermistors. Dress wiring.

22. Evacuate and charge the system. Use originalfactory charge quantity of R-134a. (SeeEvacuation and Charging Procedure .)

23. Replace all component parts in the freezer.

24. Reinstall the rear access cover.

Replacing Freezer Evaporator Using theLOKRING Method

Parts Needed:Freezer Evaporator (part # WR85X10061)Drier Assembly (part # WR86X93)

Access Tube (part # WJ56X61).)

LOKRING Connectors (part # WR97X10021)Note: If it is determined that the epoxy joints (thetransition joint between the aluminum and copper


1. Follow steps 1 through 6 under ReplacingFreezer Evaporator Using the Brazing Method.

2. Using the tubing cutter, cut the freezerevaporator jumper of the check-valveassembly (top) as close as possible to the

joint of the copper jumper. Cut the jumpertube (left side) on the inlet of the freezerevaporator (capillary joint) as close aspossible to the epoxy joint.

SuctionTubeLineCut

Here

FFEvaporator

Outlet

CapillaryTube

CutHere

8/11/2019 31-9118 part2

5/31 36

3. Loosen the hex-head screws that hold theevaporator in place. Note locations of thefoam blocks at sides of old evaporator. Theseare needed for proper airow. Remove thefoam blocks and save for new evaporatorinstallation. Remove old evaporator.

4. Modify replacement evaporator to useLOKRING connectors.

a. Using the tubing cutter, cut the jumpertube (top) at the outlet end of the freezerevaporator. Leave as much of the straighttube portion as possible from the joint ofthe check-valve assembly. Discard thecheck-valve assembly.

b. Using the tubing cutter, cut the jumpertube (left side) on the inlet end of theevaporator (capillary joint) about 3 inchesfrom epoxy joint. Make two joints usingthe LOKRING connectors for 5/16 -in. copperto copper joints.

CutHere

CutHere

5. Install the new evaporator and tighten allmounting screws.

6. Remove the old drier by cutting the haloloop as close as possible to the drier. Installthe new drier assembly (make sure there issufcient space between the tubing).

7. Install the access tube. Clean and inspect

joints.8. Replace the heater supplied in the kit.

Reinstall foam blocks, thermostat andthermistors. Dress the wiring.


10. Replace all component parts in the freezer.


Loosen Hex-Head Screws

8/11/2019 31-9118 part2

6/31 37

4. Carefully pull the cover forward, thendisconnect the fresh food evaporator fan.

Disconnect

Fresh Food Evaporator

1. Remove the custom cool drawer andnecessary drawers and covers above thecustom cool drawer, to expose the evaporatorcover housing.

2. Remove the water line coil cover.

Note: The water line coil cover is slotted. Toremove it, slide the water line coil cover towardthe door opening.

3 Remove the 3 Philips-head screws that holdthe fresh food evaporator fan cover in place.

Water Line Coil Cover

Evaporator Cover

Screw

ScrewScrew

FF Evaporator Fan

5. Loosen the 2 Phillips-head screws that holdthe fresh food evaporator in place.

6. Carefully lift and pull the fresh food evaporatorforward. Cut the tie strap that holds thethermistor block in place.

7. Remove the evaporator thermistor and blockfrom the evaporator.

Screw Screw

8/11/2019 31-9118 part2

7/31 38

Replacing Fresh Food Evaporator Usingthe Brazing Method

Parts Needed:Fresh Food Evaporator (part # WR85X10060)

Drier Assembly (part # WR86X93) Access Tube (part # WJ56X61)

Heat Shield Kit (part # WX5X8926)Caution: A heat shield kit is required for thisprocedure to prevent damage to the plasticinterior (liner) of the freezer compartment.

Note: If it is determined that the epoxy joints (thetransition joint between the aluminum and copper


1. Unplug the refrigerator.

2. Remove the rear access cover and evacuatethe sealed system. (See Evacuation andCharging Procedure .)

3. Remove components necessary to exposeboth the freezer and fresh food evaporators.(See Freezer Evaporator and Fresh FoodEvaporator .)

4. Remove the 2 foam tubes that are wire tied

to the inlet and outlet tubes of the fresh foodevaporator.

5. Remove the Styrofoam block that is insertedinto the opening in the mullion wall anddiscard. A replacement is provided.

6. Loosen the 2 screws that attach the freshfood evaporator to the liner.

Loosen 2 ScrewsStyrofoamBlock

Foam Tubes

WireTie

7. Pull the evaporator away from the liner andremove the thermistor from the aluminumblock attached to the rear of the evaporator.

8. Look into the freezer compartment and locatethe epoxy joints on the tubes leading to thefresh food evaporator. (These joints will belocated on the right hand side of the freezerevaporator.)

EpoxyJoints

9. To allow easier access to the epoxy joints,pull them away from the side of the freezerevaporator into the freezer compartment.

10. Using the tube cutter, cut the 5/16 -in. OD

copper tube as close to the epoxy joint aspossible. Score and break the capillary tubeas close to the braze joint as possible.

11. Remove the fresh food evaporator.

12. Install new fresh food evaporator.

8/11/2019 31-9118 part2

8/31 39

13. Connect the capillary tube to the inlet tubeof the evaporator. Connect the 5/16 -in. OD copper tube to the outlet tube of theevaporator (remove any excess length asrequired to obtain the correct t).

14. Apply a liberal amount of thermal pastearound both epoxy joints to prevent heat fromdamaging joint integrity.

15. Install a metal brazing shield between the joints and the plastic liner.

16. Protect the freezer oor from molten solderduring brazing.

17. Angle torch so that the ame is directed awayfrom the plastic liner. Braze both joints. Cleanand inspect joints. Remove the brazing shield.

18. Clean thermal paste off the joints. Dress the joints to the right of the freezer evaporatorso the freezer evaporator cover can bereinstalled without interference.

19. Reinsert the thermistor into the aluminumblock on the rear of the new fresh foodevaporator.

20. Attach the evaporator to the fresh food linerusing the original screws. Ensure that thedrain pan is properly positioned. Install a newStyrofoam block into the hole of the mullion.

Attach foam tubes to evaporator inlet/outlet

tubes using wire tie provided.

21. Remove the old drier by cutting the condenserloop as close as possible to the drier. Installthe new drier assembly, making sure thatthere is sufcient space between the tubing.Install the access tube on the compressor.


23. Replace all component parts in both thefreezer and the fresh food compartments.


Replacing Fresh Food Evaporator Usingthe LOKRING Method

Parts Needed:Drier Assembly (part # WR86X93)Process Tube (part # WJ56X61LOKRING Connectors (part # WR97X10021)

Note: If it is determined that the epoxy joints(transition joint between the aluminum and copper


1. Follow steps 1 through 9 under ReplacingFresh Food Evaporator Using the BrazingMethod.

2. Using the tube cutter, cut both copper tubes

as close to the epoxy joint as possible. Leaveas much 5/16 -in. tubing as possible for a goodLOKRING connection.

3. Remove the fresh food evaporator.

4. Modify replacement evaporator to useLOKRING connectors.

a. Using the tubing cutter, cut the jumpertube at the outlet end of the evaporator2 inches from the epoxy joint.

b. Cut the jumper tube on the inlet end of theevaporator (capillary joint) 1 1/2 inches fromthe epoxy joint. Make two joints using theLOKRING connectors for 5/16 -in. copper tocopper joints.

Inlet TubeOutlet Tube

2"

EpoxyJoints

1-1/2"

8/11/2019 31-9118 part2

9/31 40

5. Reinsert the thermistor into the aluminumblock on the rear of the new fresh foodevaporator.

6. Attach the evaporator to the fresh food linerusing the original screws. Ensure that drainpan is properly positioned. Install a newStyrofoam block into the hole of the mullion.

Attach foam tubes to the evaporator inlet/

outlet tubes using wire tie provided.7. Remove the old drier by cutting the condenser

loop as close as possible to the drier. Installthe new drier assembly (make sure there issufcient space between the tubing). Installthe process tube on the compressor.


9. Replace all component parts in both thefreezer and the fresh food compartments.


Accumulator

The accumulator collects any liquid refrigerantleft in the evaporator before it enters thesuction line.

The liquid refrigerant pools in the bottom

of the accumulator until it is drawn into thecompressor as a vapor.

The accumulator comes as a part of thefreezer evaporator. It is not availableseparately.

Check Valve

A nylon piston inside the check valve oatsback and forth, depending upon refrigerantow.

The check valve prevents refrigerant fromowing back into the freezer evaporator.

When the main control rotates the 3-wayvalve for fresh food only cooling, the checkvalve will prevent refrigerant from owingin the freezer evaporator (refrigerant willnaturally ow to the coldest area).

The check valve is only available with a newfreezer evaporator.

Caution: Do not attempt to replace only thecheck valve. The nylon piston in the check valveis extremely heat sensitive.

Check Valve

8/11/2019 31-9118 part2

10/31 41

Troubleshooting

Enter the appropriate display numbersas shown below and press any pad other

than the temperature pads to activatethat test mode. Not all test modes are

available on all models.

Enter the diagnostic mode by pressing both the freezer temperature (COLDER and WARMER) pads

and the refrigerator temperature (COLDER and WARMER) pads simultaneously. All four pads mustbe held for approximately 3 seconds. Blinking "0"s in both displays indicate the refrigerator hasentered the test mode.

Control Diagnostics

FreezerDisplay

FreshFood

DisplayDiagnostics Results Comments

0 2 Communication check betweenTemperature Control and Main Control"P" on freezerdisplay if OK. "F" ifproblem is found.

0 4 Communication check betweenDispenser Control and Main Control

"P" on freezerdisplay if OK. "F" ifproblem is found.

0 6 Temperature Control LED Test

All LEDs light.Pressing thecorresponding padturns off the LED.

See Note 3 .

0 7 Control and Sensor System Test

Checks each

thermistor anddisplays "P" for passand "0" for fail.

See Note 1 .

0 8 Duct Door Test

Opens the dispenserduct door for 10seconds, thencloses.

Test can beperformed with dooropen.

8/11/2019 31-9118 part2

11/31 42

FreezerDisplay

FreshFood

DisplayDiagnostics Results Comments

1 0 Dampers Test

Double damper willopen, close after10 seconds, pausebriey, then singledamper will open for10 seconds.

Test will not start for20 seconds afterpad is depressed.

1 1 Fan Test Cycles through eachfan for 5 seconds.

1 2 100% Run Time

Sealed system on100% of the time.Times out after 1hour.

1 3 Prechill TestStarts Prechill mode.Unit returns tonormal on its own.

1 4 Defrost TestToggles on thedefrost cycle. See

Note 2 .

Must press againto turn heaters off.

See Note 2.1 5 Main Control Reset

Causes a systemreset.

1 6 Exit Diagnostics ModeCauses atemperature controlboard reset.

Note 1: Display order is #1 = Fresh Food Evaporator Thermistor, #2 = Fresh Food Thermistor, #3 =Custom Cool Thermistor, #4 = Freezer Evaporator Thermistor, #5 = Freezer Thermistor.

Thermistor test results are: P = Pass, 0 = Fail, S = Short to 5 VDC, B = Bad amplier (replace maincontrol).

Note 2: You must enter the defrost test again to toggle the defrost heater off at the end of the test. Theheater will not come on if the evaporator thermistor is above 70F.

Note 3: To exit the Temperature Control LED Test, press both refrigerator temperature pads (COLDERand WARMER) simultaneously for 3 seconds.

8/11/2019 31-9118 part2

12/31 43

Schematic

J - 1 2

J 1 - 1 J 5 - 6 J 5 - 4 J 5 - 3 J 5 - 1 J 5 - 2 J 5 - 5 J 1 - 2 J 1 - 3 J 1 - 4 J 1 - 5 J 2 - 1 J 2 - 2 J 2 - 3 J 2 - 4 J 2 - 5 J 2 - 6 J 2 - 7 J 2 - 8 J 4 - 3

T A B 1 T A B 2 J 7 - 6 J 7 - 7 J 7 - 4 J 7 - 3 J 7 - 2 J 7 - 1 J 7 - 9 J 7 - 5 T A B 4

J 4 - 2 J 4 - 1

J 1 5 - 1 J 1 5 - 2

A C

B R O W N

B L A C K

B R O W N

C O M P R E S S O R

B L A C K

B L U E

B L U E

P U R P L E

P U R P L E

P U R P L E P

U R P L E

P U R P L E

P I N K

B R O W N

R E D

B R O W N

B R O W N

B R O W N

B R O W N

W H I T E

W H I T E

W H I T E

W A T E R

V A L V E

Y E L L O W

W H I T E

I C E M A K E R

Y E L L O W

F R E E Z E R D O O R

I N T E R L O C K

R E D / W H I T E ( A

U G E R I M P U T )

B L U E

D E F R O S T

H E A T E R

O R A N G E

W H I T E

R E D

I N V E R T E R

O R A N G E

O R A N G E

O R A N G E

O R A N G E

O R A N G E

O

R A N G E

F R E S H F O O D

L I G H T ( T O P )

F R E S H F O O D

L I G H T ( M I D )

F F T H E R M O S T A T

O R A N G E

O R A N G E

O R A N G E

O R A N G E

O R A N G E

O R A N G E

A U G E R

S I L V E R

S I L V E R

S I L V E R

B E I G E

O R A N G E

O R A N G E

B L U E / W H I T E

T O C U S T O M C O O L

H E A T E R

R = 4

0 4

B E I G E

B E I G E

C U B E

R = 9

1

O R A N G E O R A N G E

O R A N G E

R E D

O R A N G E O R A N G E

O V E R T E M P E R A T U R E

T H E R M O S T A T

P I N K

W H I T E

R E D

3 - W a y

V a l v e

T H E R M I S T O R

F F E V A P .

T H E R M I S T O R F F

T H E R M I S T O R C C T

H E R M I S T O R F Z

T H E R M I S T O R F Z E V A P .

J 3 - 1

0

J 3 - 9

J 3 - 8

J 3 - 7

J 3 - 6

3 - W a y

V a l v e

W H I T E + G R E Y

B L A C K

Y E L L O W

R E D

O R A N G

E

F R E E Z E R D O O R

F F C O M P A R T M E N T

D U C T S O L E N O I D

R E D

R E D

B L A C K

B L A C K

T O H T R

1

4

Y E L L O W

R E D

R E D B L A C K

W H I T E Y E L L O W

G R A Y

D E P . S W I T C H

D E P . S W I T C H

J 2 - 4 J 2 - 3 J 2 - 2 J 1 - 1

J 1 - 2

J 4 - 1 J 4 - 2 J 4 - 3 J 4 - 6

B L A C K

B L A C K

R E D

B L U E

B L A C K

B L A C K

( C O M M )

R E D

B L U E

( C O M M )

S M A R T

T R O L L E Y

R E D

+ 1 2 V R E D

T A N

B L A C K / W H I T E

Y E L L O W

Y E L L O W / B L A C K

W H I T E / S I L V E R ( C O M M )

B L U E / W H I T E ( M O D E L )

B L U E ( R P M )

+ 5 V B L U E

B L U E / W H I T E

R E D / W H I T E

Y E L L O W

Y E L L O W / B L A C K

B R O W N

P I N K

Y E L L O W

B L U E / R E D

B L U E

B L U E

D I S P L A Y B O A R D

M A I N C O N T R O L B O A R D

T E M P E R A T U R E

C O N T R O L

J 3 - 3

J 3 - 2

J 3 - 1

R E D

F F F A N

C C F A N

E V A P . F A N

C O N D

. F A N

R E D

Y E L L O W

W H I T E

R E D

Y E L L O W

W H I T E

B L U E

W H I T E / G R E E N

W H I T E / G R E E N

W H I T E / B L A C K

W H I T E / B L A C K

W H I T E / B L U E

W H I T E / B L U E

W H I T E / R E D

W H I T E / R E D

L O W

V O L T A G E D C

L I N E V O L T A G E

S I N G L E D A M P E R

D U A L D A M P E R

1 0

1 0

1 0

R = 2

1 . 1 5

F F S W I T C H

C U S T O M C O O

L L I G H T

F R E E Z E R L I G H T

D I A G R A M

I N S I D E

I C E M A K E R

H O U S I N G

R = 1

8 0

R = 3 . 3

4

C O M P R E S S O R

1 0

1 0

1 0

8/11/2019 31-9118 part2

13/31 44

Illustrated Parts

8/11/2019 31-9118 part2

14/31

8/11/2019 31-9118 part2

15/31 46

8/11/2019 31-9118 part2

16/31 47

8/11/2019 31-9118 part2

17/31 48

8/11/2019 31-9118 part2

18/31 49

8/11/2019 31-9118 part2

19/31 50

8/11/2019 31-9118 part2

20/31 51

8/11/2019 31-9118 part2

21/31 52

8/11/2019 31-9118 part2

22/31 53

8/11/2019 31-9118 part2

23/31 54

VIEW NUMBER CATALOG NUMBER DESCRIPTION QUANTITY

0001 31-51518 PM MINI WIRING MANUAL 10001 49-60238 PM GUIDE OWNERS 10006 WR12X10561 HANDLE SOFT TOUCH INSERT 20010 WR01X10065 SCR 8-18 BA POR 5/8 SS 150011 WR38X10245 TRIM RECESS WH 1

0012 WR02X10649 STOP DOOR WH 20014 WR24X10156 GASKET DOOR FZ WH 10015 WR02X10638 CAM CLOSURE FZ WH 10016 WR02X10637 CAM CLOSURE FF WH 10023 WR71X10499 MODULE FZ UPPER 10025 WR71X10500 MODULE FZ SEAT 10026 WR71X10495 GUIDE ICE 10027 WR01X10387 SCR 8-18 AB OVP 7/8 SS 20031 WR17X11654 GRILLE RECESS WH 10036 WR62X10020 SOLENOID ASM 10045 WR02X8818 RETAINER RECESS DOOR 20056 WR02X10675 BULB RECS 12V 10058 WR17X11081 HOUSING SHIELD DISP WH 10061 WR02X9561 LAMP SOCKET 10062 WR17X11653 DOOR RECESS ASM 10063 WR02X10585 SPRING RECESS DOOR 10067 WR17X10706 CRANK DOOR RECESS 10069 WR17X11264 FUNNEL ICE DISP WH 10070 WR17X11265 EXTENSION FUNNEL ICE WH 1

0070 WR49X10075 EXTENSION FUNNEL ICE WH 10072 WR23X10224 SWITCH 10074 WR02X10584 SPRING FUNNEL 10080 WR02X11330 UNION CONNECTOR 10093 WR55X10469 INTERFACE DISP ASM 10095 WR17X11481 WINE & BEVERAGE RACK 10103 WR24X10155 GASKET DOOR FF WH 10104 WR04X10129 LENS NAMEPLATE 10106 WR22X10042 DOOR DAIRY CLEAR 10107 WR22X10041 COMPARTMENT DAIRY 10109 WR71X10594 MODULE SHELF FF 10110 WR71X10297 MODULE SHELF FIXED FF 10111 WR71X10298 INSERT MODULE FF FIXED 10112 WR02X10639 SNUGGER 20115 WR71X10253 MODULE SHELF FF 20116 WR22X10043 TRIM DAIRY COMPARTMENT 10122 WR71X10256 MODULE SUPPORT FZ 2

8/11/2019 31-9118 part2

24/31 55


0123 WR71X10255 MODULE SUPPORT FZ 10124 WR21X10053 BASKET WIRE TILTOUT FZ 10125 WR21X10054 BASKET WIRE TILTOUT FZ 20127 WR71X10380 MODULE SHELF INSERT 30151 WR01X1554 SCR 8-18 AB IHXW 1/2 S 14

0159 WR14X10067 FOAM STRIP SE ADH 10160 WR14X10068 FOAM STRIP SE ADH 10161 WR17X11257 DUCT EXTENSION FZ ASM 10164 WR14X10164 GASKET PLENUM 10165 WR14X10167 GASKET MOTOR COVER 20167 WR17X11477 PLENUM FAN EVAPORATOR 10168 WR02X10674 BRACKET FZ TOWER LOWER 10175 WR01X10035 SCR 8-18 AB IHW 5/8 S 230177 WR01X10240 8-8X7/16 TORX PAN HEAD 90178 WR01X10241 8-18X13/16 TROX PAN HEAD 90179 WR12X10624 HANDLE 10180 WR71X10527 SHELF FIXED FZ 10181 WR38X10214 TRIM SHELF FZ 20182 WR71X10498 SHELF ADJUSTABLE FZ 10184 WR21X10040 BASKET FZ LONG 30185 WR12X10625 HANDLE 30186 WR21X10041 BASKET WIRE FZ SHORT 10189 WR17X10945 SPACER 30190 WR72X10066 SUPPORT SLIDE BASKET RH 1

0191 WR72X10067 SUPPORT SLIDE BASKET LH 10194 WR02X10810 COVER L.H. 30195 WR02X10811 COVER R.H. 30196 WR72X10068 SLIDE & BRACKET ASM LH 30197 WR72X10069 SLIDE & BRACKET ASM RH 30198 WR72X10070 SLIDE LINER 60200 WR17X11702 COVER FF AIR TOWER 10201 WR17X11703 EPS FF TOWER 10200 WR17X11805 COVER FF AIR TOWER 10202 WR14X10188 GASKET TOWER FF 20203 WR17X11711 COVER WATER FILTER 10204 WR02X10676 FRAME SUPPORT PINS 60202 WR17X11805 GASKET TOWER FF 20208 WR01X10431 NUT 6-32 UN 10210 WR74X10131 GUARD WIRING 10212 WR02X10689 GROMMET BASE GRILLE 20213 WR17X11803 COVER EVAPORATOR FRONT 10214 WR14X10153 GASKET EVAP COVER 2

8/11/2019 31-9118 part2

25/31 56


0210 WR74X10131 GUARD WIRING 10215 WR01X10211 BRACKET FZ TOWER UPPER 20217 WR32X10154 DIAL PAN CHILL 10218 WR02X10665 LINKAGE PAN CHILL 10219 WR02X10664 SHUTTER PAN CHILL 1

0220 WR02X11851 EPS PAN CHILL 10221 WR02X11852 DISCHARGE PAN CHILL 10222 WR02X10666 KNOB PAN CHILL 10224 WR02X11853 FOAM STRIP SE ADH 10225 WR02X11426 TUBE DRAIN 10226 WR02X11848 TUBE DRAIN 10227 WR23X10337 HARNESS AC FZ INTERMEDIA 10228 WR85X10061 LOW SIDE ASM FZ 10229 WR02X10552 CLIP EVAP THERMISTOR 10230 WR51X10042 HEATER & BRACKET ASM 10231 WR02X10669 BLOCK EVAP SEAL 30232 WR17X10811 SHIELD ASM TROUGH 10233 WR55X10026 SENSOR TEMP FZ 10234 WR02X10647 GRILLE SENSOR 20235 WR02X10668 SHUNT SENSOR 20237 WR55X10028 SENSOR TEMP FF 10240 WR50X10028 DEFROST THERMOSTAT 10233 WR55X10025 SENSOR TEMP FZ 10241 WR55X10025 SENSOR TEMP FF 1

0247 WR17X10812 ORIFICE FAN ASM 10248 WR14X10168 GASKET MOTOR COVER 20237 WR55X10025 SENSOR TEMP FF 10249 WR14X10165 GASKET PLENUM 10250 WR14X10069 FOAM STRIP SE ADH 10256 WR17X11713 SHIELD LIGHT FF 10257 WR02X10663 STAND OFF 40258 WR17X11480 SHIELD LIGHT FZ 10259 WR17X11712 LIGHT SHIELD 10261 WR13X10137 HINGE BTM & PIN ASM WH 10263 WR02X10648 PIN HINGE BTM ADJ HOLLOW 10268 WR01X10210 SCREW MOBILITY 3.5 20270 WR17X11506 GROMMET AND TUBE ASM 10278 WR02X10636 MOBILITY FRONT ASM 20280 WR02X10640 CAP CORNER OC WH 20288 WR74X10071 GRILL BASE ASM AWH 10306 WR02X10833 SCREW MOBILITY 23 2

8/11/2019 31-9118 part2

26/31

8/11/2019 31-9118 part2

27/31 58


0380 WR17X1064 PLUNGER SOLENOID 10381 WR02X4257 PIN SPIRAL 10382 WR02X4258 SPRING SOLENOID LINKAGE 10383 WR17X1065 COLLAR SOLENOID DISP 10384 WR17X1066 STIRRUP SOLENOID DISP 1

0385 WR02X4259 PIN SPIRAL 10386 WR02X11767 BOOT AUGER MOTOR INT 10387 WR17X11478 COVER BUCKET BOTTOM 10400 WR01X10209 WHEEL PAN COVER 80401 WR01X10214 SCR 10-16 PL PNP 5/8 SZN 80405 WR02X11254 DIFFUSER FF INLET LT 10405 WR02X11255 DIFFUSER FF INLET RT 10407 WR32X10339 PAN MIDDLE CHILL ASM 10409 WR32X10200 COVER PAN GLASS 10410 WR32X10197 COVER MIDDLE PAN 10413 WR02X10650 HUMIDITY CONTROL 10414 WR14X10059 GASKET PAN CRV FRONT 10417 WR14X10058 GASKET PAN CRV REAR 10418 WR02X10633 SLIDE MIDDLE PAN COVER 10421 WR55X10389 INTERFACE CUSTONER ASM 10433 WR02X9391 SOCKET & TERMINAL ASM 40434 WR02X10645 SOCKET LAMP 20435 40A15 LAMP 40 W 40437 60A LAMP 60 W 2

0447 WR02X10831 COVER HINGE FZ BK 10448 WR13X10214 HINGE TOP & PIN ASM FZ 10449 WR13X10215 HINGE TOP & PIN FF 10450 WR02X10832 COVER HINGE FF BK 10451 WR13X10126 HINGE BTM WH 10453 WR23X10209 HARNESS/TSTAT FF LT 10454 WR01X10212 NUT 8-32 20456 WR71X10595 BEZEL LIGHT FF 10470 WR32X10196 COVER TOP PAN ASM 10471 WR32X10338 PAN ASM TOP 10481 WR31X10036 TRAY CUSTOM COOL 10482 WR17X11787 WIREFRAME PAN 10487 WR32X10434 PAN FRAME ASM 10501 WR71X10296 SHELF SLIDEOUT ASM 20505 WR02X10662 STOP SHELF 30530 WR71X10294 SHELF TUCKAWAY ASM 10540 WR31X10038 COVER PAN ASM 10552 WR01X2022 SCREW 10

8/11/2019 31-9118 part2

28/31 59


0553 WR01X10314 SCREW HANDLE MTG 60580 WR72X10140 SLIDE AND BRACKET ASM 20581 WR72X10141 SLIDE LINER 20582 WR72X10142 SPACER SLIDE 20583 WR01X10399 SCR 8-18 AB HW 1/2 S 6

0602 WR01X1591 SCR 1/4-14 X 3/4 20608 WR23X10179 SWITCH LIGHT 10609 WR23X10175 SWITCH LIGHT 10610 WR60X10099 MOTOR DC EVAP FAN ASM 10611 WR02X10764 BRACKET EVAP FAN BTM 10612 WR02X10653 BRACKET ORIFICE FAN 10613 WR60X10075 BLADE EVAP FAN ASM 10614 WR02X10540 BUMPER LID 30615 WR02X10519 GROMMET EVAP FAN 20616 WR82X10093 COVER ACCESS 10618 WR02X11331 GROMMET EVAP FAN 20625 WR01X5278 CLAMP CABLE 20626 WR23X0108 HARNESS CORD POWER 10610 WR60X10043 MOTOR DC EVAP FAN ASM 10626 WR23X0108 POWER CORD 10628 WR17X11252 SHROUD CONDENSER 10650 WR60X10080 MOTOR DC COND FAN 10651 WR60X10049 BLADE COND FAN ASM 10652 WR02X10509 RING COMPRESSION 2

0653 WR02X10322 CAP DUST 10616 WR82X10071 COVER ACCESS 10683 WR02X11027 WIRE TIE 10686 WR01X10252 SCR 10-32 TT HXW 5/16 S 100690 WR01X1466 SCR 8-32 T HXW 3/8 S 70626 WR23X10300 HARNESS CORD POWER 10691 WR02X10593 BRACKET COND FAN (REAR) 10725 WR87X10064 INVERTER COMPRESSOR EMB 10626 WR23X10300 POWER CORD 10727 WR17X11503 SEPARATOR AIR HISIDE 10730 WR84X10022 CONDENSER ASSEMBLY 10650 WR60X10065 MOTOR DC COND FAN 10734 WR02X11262 COVER RELAY (EMB) 10736 WR02X8203 CLIP COMPRESSOR MOUNT 40737 WR02X10099 GROMMET 40740 WR86X10030 DRYER BIFURCATED HX9 10741 WR01X1779 STUD MTG COMPR 40749 WR17X11039 BAFFLE COND AIR 10750 WR01X1786 SCREW 10-32 TR 1/2 4

8/11/2019 31-9118 part2

29/31 60


0690 WZ5X158D SCR 8-32 T HXW 3/8 S 70751 WR17X10693 BASEPLATE HIGH SIDE 10753 WR02X10521 BRKT COND FAN (MTG) 10757 WR01X10193 SCR 10-32 SPECIAL 60758 WD02X0323 SCR 8-32 X 3/8 SPH 2

0762 WR02X11857 FOAM STRIP SE ADH 10764 WR02X9000 CLIP, COND MNT 20765 WR17X10763 BRACKET CONDENSER BAR 10775 WR17X10796 COVER WATER LINE 10734 WR02X11262 COVER RELAY (EMB) 10790 GWF FILTER CANISTER 10791 WR02X11705 CAP FILTER BYPASS 10792 WR17X11028 FILTER ASM AND TUBE 10800 WR57X10040 WATER VALVE 10801 WR55X10414 BOARD ASM MAIN CONTROL 10802 WR23X10382 HARNESS BOARD INDIV 10803 WR02X11847 MAIN BOARD ENCLOSURE ASM 10805 WR02X3736 STR RELIEF 10751 WR17X10693 BASEPLATE HIGH SIDE 10806 WR17X11625 TUBE PLASTIC 10808 WR02X4039 ADHESIVE CLIP 10757 WR01X10194 SCR 10-32 SPECIAL 60809 WR01X1936 FASTENER WATER TUBE 10758 WD2X323D SCR 8-32 X 3/8 SPH 2

0810 WR17X11709 COVER TANK WATER COIL AS 10813 WR17X11710 COVER WATER TANK 10814 WR85X10060 LOW SIDE ASM FF 10815 WR17X11708 TROUGH DRAIN ASM 10816 WR17X11844 COVER EVAP ASM FF 10820 WR30X10044 ICEMAKER ASM 10821 WR02X11548 STRIPPER IM 10842 WR11X10007 LEVER ASM FF SIDE WH 10792 WR17X11618 FILTER ASM AND TUBE 10843 WR11X10008 LEVER ASM FZ SIDE WH 10800 WR57X10032 WATER VALVE 10847 WR01X2027 SPRING CLOSURE 20801 WR49X10092 BOARD ASM MAIN CONTROL 10867 WR29X10058 CUP FILL IM 10870 WR23X10381 HARNESS INVERTER COMM 10803 WR02X11473 MAIN BOARD ENCLOSURE ASM 10871 WR55X10155 INVERTER ASM EMBRACE 10900 WR78X10860 DOOR FOAM ASM FZ WH 10903 WR01X10208 THIMBLE DOOR BTM FZ WH 1

8/11/2019 31-9118 part2

30/31 61


0904 WR01X10375 SCREW DOOR STOP T20 40905 WR01X2134 SCR 10-32 PNT 1.0 S LW 20910 WR78X10600 DOOR FOAM ASM FF WH 10911 WR01X10207 THIMBLE DOOR TOP WH 20912 WR01X10206 THIMBLE DOOR BTM WH 1

0915 WR02X10844 GRILL MULLION 10920 WR31X10008 COVER UPPER 10921 WR31X10043 COVER LOWER 10922 WR60X10064 FAN CHILL 10923 WR60X10063 DAMPER ASM DESUPPLY 10820 WR30X10012 ICEMAKER ASM 10924 WR60X10062 DAMPER ASM SUPPLY 10925 WR31X10007 PLENUM TOP 10926 WR31X10009 DUCT CAVITY CHILL 10927 WR14X10095 GASKET MULLION DUCT 10930 WR51X10049 HEATER THAW 10931 WR02X10809 REFLECTOR 10932 WR14X10096 GASKET DAMPER CHILL 10933 WR31X10012 LIGHT SOCKET CHILL 10934 WR02X10812 LAMP 40W CHILL 10935 WR31X10010 GRILL BULB CHILL 10936 WR14X10092 SEAL AHU CHILL 10937 WR23X10384 HARNESS CHILL AC 10938 WR23X10237 HARNESS CHILL DC 1

0939 WR14X10090 SEAL AHU CHILL 10941 WR14X10091 SEAL AHU CHILL 10942 WR01X10239 WASHER RETAINER CHILL 40944 WR14X10093 GASKET LC 10945 WR14X10094 GASKET UC 10960 WR17X11842 GROMMET DRAIN TUBE ASM 10971 WR02X11789 BRACKET INVERTER 10980 WR57X10053 VALVE ASM 11022 WR17X11272 CAP TRIM BTM FZ WH 11024 WR17X10972 TRIM DOOR BTM FZ WH 11025 WR12X10538 HANDLE ASM TRIM FZ WH 11026 WR17X11273 TRIM DOOR SIDE FZ WH 11027 WR17X10974 TRIM DOOR TOP FZ WH 11042 WR17X11271 CAP TRIM BTM FF WH 11044 WR17X10973 TRIM DOOR BTM FF WH 11045 WR12X10539 HANDLE ASM TRIM FF WH 10930 WR51X10081 HEATER THAW 11046 WR17X11274 TRIM DOOR SIDE FF WH 11047 WR17X10975 TRIM DOOR TOP FF WH 1

8/11/2019 31-9118 part2

31/31

Warranty

All warranty service provided by our Factory Service Centers,or an authorized Customer Care technician. To schedule service,on-line, 24 hours a day, visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737).

For The Period Of: GE Will Replace:

One Year Any part of the refrigerator which fails due to a defect in materials or workmanship.From the date of the During this full one-year warranty, GE will also provide, free of charge, all labor and in-homeoriginal purchase service to replace the defective part.

Five Years Any part of the sealed refrigerating system (the compressor, condenser, evaporatorFrom the date of the and all connecting tubing) which fails due to a defect in materials or workmanship.original purchase During this full five-year sealed refrigerating system warranty, GE will also provide, free of charge,

all labor and in-home service to replace the defective part in the sealed refrigerating system.

Lifetime of Product The full extension slides, if they should fail due to a defect in materials or workmanship.From the date of the During this product lifetime limited warranty, you will be responsible for any labor or relatedoriginal purchase service costs.

Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship.From the original During this limited thirty-day warranty, GE will also provide, free of charge, a replacement waterpurchase date of the filter cartridge.refrigerator

Service trips to your home to teach you how to use

the product. Improper installation, delivery or maintenance. Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially. Loss of food due to spoilage. Replacement of house fuses or resetting of circuit

breakers. Damage caused after delivery.

Replacement of the water filter cartridge due to water

pressure that is outside the specified operating range ordue to excessive sediment in the water supply. Replacement of the light bulbs or water filter cartridge

other than as noted above. Damage to the product caused by accident, fire, floods

or acts of God. Incidental or consequential damage caused by possible

defects with this appliance.

What GE Will Not Cover:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your states Attorney General.

31-9118 part2

Documents

Transcript of 31-9118 part2