3054c Pistons and Connecting Rods - Remove

Desmontagem e Montagem 3054C Engines for Caterpillar Built Machines

Pistons and Connecting Rods - Remove

SMCS - 1225-011

Removal Procedure

Start By:

A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". B. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and

Install". C. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove". D. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove

and Install".

1. Use Tooling (A) in order to remove the carbon ridge from the top inside surface of the cylinder liners.

2. Rotate the crankshaft until the pistons that are being removed are at the bottom center position.

Fechar o SIS

Tela anterior

produtos: VIBRATORY COMPACTOR Modelo: CP-533E VIBRATORY COMPACTOR DAM Configurao: CS-533E CP-533E Vibratory Compactor DAM00001-UP (MACHINE) POWERED BY 3054C Engine

Nmero de Mdia -SENR5069-07 Data de Publicao -01/06/2009 Data de Atualizao -22/06/2009

i02301207

Table 1

Required Tools

Tool Part Number Part Description Qty

A 8S-2269 Ridge Reamer 1

NOTICEKeep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Page 1 of 3CS-533E CP-533E Vibratory Compactor DAM00001-UP (MACHINE) POWERED BY ...

8/12/2011https://127.0.0.1:444/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
https://127.0.0.1:444/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis

3. Remove the setscrews (1) .

Note: Do not reuse the setscrews (1) . Use new setscrews in order to secure the connecting rod cap for reassembly.

4. Remove the connecting rod cap (2) and the connecting rod bearing.

Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.

Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture.

5. Put a temporary identification mark on the top of the piston in order to indicate the cylinder number that is shown on the connecting rod. Put the temporary mark on the same side as the mark that is on the connecting rods in order to ensure correct assembly of the piston and the connecting rod.

Note: Do not etch the top surface of the piston. Do not allow scratches or stamped markings in the top surface of the piston.

6. Push the pistons and the connecting rods through the top of the cylinder block.

7. Repeat Steps 2 through 6 in order to remove the remaining pistons and connecting rods.

Illustration 1 g00970465

Direitos Autorais 1993 -

2011 Caterpillar Inc.

Todos os Direitos Reservados.

Thu Dec 8 12:04:42 UTC-0200 2011



Rede Particular Para Licenciados SIS.



This document was created with Win2PDF available at http://www.win2pdf.com.The unregistered version of Win2PDF is for evaluation or non-commercial use only.This page will not be added after purchasing Win2PDF.
http://www.win2pdf.com

3054c Pistons and Connecting Rods - Remove

Documents

Transcript of 3054c Pistons and Connecting Rods - Remove