300,000TON/YEAR USED STEEL BAR ROLLING MILL · 300,000ton/year used steel bar rolling mill 6 1.2.8....

300,000TON/YEAR USED STEEL BAR ROLLING MILL

1

Project No. 98004

TECHNICAL PROPOSAL FOR

300,000T/Y USED BAR ROLLING MILL EQUIPMENT

50 T/ HR


2

CONTENTS I). GENERAL ----------------------------------------------------------------------------------- ----- -P2～P17 II.). DESIGN BASIS --------------------------------------------------------------------------------- -P18～P20 III.). EQUIPMENT SUPPLY LIST ---------------------------------------------------------------- -P21～P27 IV).LAYOUT AND PHOTO------------------------------------------------------------------------ -P28～P63 1. GENERAL 1.1 PREFACE Remark: This bar mill is on operation now , Capacity :300,000TON， Built in 1984, was made by TANAKA Japan, capacity 30TON/HR ROLLING MILL， in 2006 invested USD4,000,000 revamping and Modefied to (1).new 60TON/HR REHEATING FURNACE, Material is billet in SQ100mm、SQ120mm、SQ130mm、SQ150mm、SQ160mm ; (2)new 650mm∮ BREAKING DOWN MILL×3set; (3)6 PASS ROUGH MILL changed to DC MOTOR DRIVE×3set; (4) 6 PASS INTERMEDIATE MILL REDUCE GEAR change to straight line ; (5) 6 PASS FINISHING MILL changed to DC MOTOR DRIVE × 4set to increase production speed ; (6) new packing line ， BAR AUTO BUNDLING MACHINE OF SUND BRISTA SWEDEN, Capacity upgrade to 50TON/HR， Due to new bar mill in northern Taiwan, , It will be shut down in mid 2013


3

The following description is the rolling mill equipment with an annual production capacity of 300,000 TON, the original equipment

was built in 1984 by Tanaka Co., Ltd. from Japan, and provides an original production of 30TON/HR ROLLING MILL, And

invested a capital of USD4, 000,000 in 2006 to updated equipments; (1 ) A new 60TON/HR REHEATING FURNACE uses raw

materials of SQ100mm, SQ120mm, SQ130mm, SQ150mm, SQ160mm BILLET; (2) A new 650mm ∮ BREAKING DOWN MILL ×

3set; (3) 6 PASS ROUGH MILL replaced DC MOTOR DRIVE × 3set ; (4) 6 PASS INTERMEDIATE MILL REDUCE GEAR

replaced with tallied inline mill gear ratio; (5) 6 PASS FINISHING MILL replaced DC MOTOR DRIVE × 4set to change the

production rate; (6) A new automated packaging lines, with an additional BAR AUTO BUNDLING MACHINE OF SUND BRISTA

SWEDEN and other production processes to achieve the present production capacity 50TON/HR. Due to a building of a new plant,

and is expected to go into operation in August 2010; The equipment mentioned above are to be stop of production, all machineries

and equipments are for sale, and should empty the factory at the end of 2010.

The following description is the rolling mill equipment with an annual production capacity of 300,000 TON, the original equipment

was built in 1984 by Tanaka Co., Ltd. from Japan, and provides an original production of 30TON/HR ROLLING MILL, And

invested a capital of USD4, 000,000 in 2006 to updated equipments; (1 ) A new 60TON/HR REHEATING FURNACE uses raw

materials of SQ100mm, SQ120mm, SQ130mm, SQ150mm, SQ160mm BILLET; (2) A new 650mm ∮ BREAKING DOWN MILL ×

3set; (3) 6 PASS ROUGH MILL replaced DC MOTOR DRIVE × 3set ; (4) 6 PASS INTERMEDIATE MILL REDUCE GEAR

replaced with tallied inline mill gear ratio; (5) 6 PASS FINISHING MILL replaced DC MOTOR DRIVE × 4set to change the

production rate; (6) A new automated packaging lines, with an additional BAR AUTO BUNDLING MACHINE OF SUND BRISTA

SWEDEN and other production processes to achieve the present production capacity 50TON/HR. Due to a building of a new plant,

and is expected to go into operation in August 2010; The equipment mentioned above are to be stop of production, all machineries

and equipments are for sale, and should empty the factory at the end of 2010.

THE STEEL GRADES WHICH ARE TO BE PROCESSED ON THE MILL ARE AS FOLLOWS.


4

A). DEFORMED BAR : D10~D40 STEEL BARS, APPLICABLE STANDARDS: JIS 20-2525＆24-2536 “ROLLED STEEL

FOR GENERAL STRUCTURE”

B). RUNG BAR : ∮9.5mm～∮40mm STEEL BARS JIS G 3101&JIS G4051

C). PRODUCT LENGTH OF BARS: 12M OR OTHERS

LAYOUT : VPLEASE REFER TO ATTACHED GENERAL LAYOUT.

1) .ROLLING MILL : THE BILLET IS CHARGED ON THE BILLET CHARGING BED BY THE BILLET YARD CRANE,

AND TRANSFERRED TO THE PUSHER TYPE 60 TON/HR REHEATING FURNACE BY THE BILLET CHARGING

ROLLER TABLE. AND THE HEATED BILLET ARE DISCHARGED FROM REHEATING FURNACE MAIN PUSHER AND

PROCESSED THROUGH ROUGHING MILL TRAIN, INTERMEDIATE TRAIN, FINISHING MILL TRAIN。

THE ROLLING MILL COMPRISES A TOTAL OF 21 STANDS，DIVIDE IN BREAKING DOWN MILL WITH 3 STANDS

(3PASS)，ROUGHING MILL WITH 6 STANDS (6 PASS), INTERMEDIATE MILL WITH 6 STANDS (6 PASS), FINISHING

MILL WITH 6 STANDS (6PASS). THE ROUGHING ROLLING MILL BY THE 3 SET MONOMER DRIVEN BREAKING

DOWN MILL ARE ROLLER BEARING 3PASS AND 3SET ONE INLET TO TOW OUTLET DRIVEN ROUGH MILL ARE

FIBER BEARING 6 PASS FORMED，DRIVEN ARE DC MOTOR，INTERMEDIATE MILL ARE 3SET ONE INLET TO TOW

OUTLET DRIVEN INTERMEDIATE MILL ARE ROLLER BEARING 6 PASS FORMED，DRIVEN ARE AC MOTOR，BUT

THE FINISHING ROLLING MILL ARE 2SET ONE INLET TO TOW OUTLET DRIVEN FINISHING MILL ARE ROLLER

BEARING 4 PASS AND 2 SET MONOMER DRIVEN FINISHING MILL ARE ROLLER BEARING 2PASS FORMED，

DRIVEN ARE DC MOTOR，ALL STANDS ARE ARRANGED IN HORIZONTAL ARRANGEMENT.

2) .COOLING BED: ON THE WAKING BEAM TYPE 6MtrW×55MtrL COOLING BED, MAIN COMPONNENTS ARE 4

STRANDS RUN IN ANGLE, BREAK, KICK OFF, FIXED RAKES, MOVABLES, DRIVE GROUP, RUN OUT DEVICE ,


5

PRODUCTS ARE COOLD DOWN TO DESIRED TEMPERATURE, WHILE MAINTAINING THE STREIGHTNESS.

3) LENGTH CUTTING & FINISHING BUNDLING SYSTEM FOR DEFORMED BAR.

THOSE PRODUCTS ARE THEN DISCHARGED FROM THE COOLING BED AND FURTHER PROCESSED BY LENGTH

CUTTING AND FINISHING BUNDLING SYSTEM. ALL PRODUCTS ARE CUT TO LENGTH BY CUT FORCE D32×12Apcs

(400TON) COLD SHEAR TRANSFERRED TO RECEIVING CONVEYOR. AT THE END OF THE CONVEYOR，A

CONVEYED TABLE IS LOCATED WHICH TRANSFER THE PRODUCTS TO BUNDLING AREA TO SHIPPING AREA。

1.2 PLANT DESCRIPTION This mill has the area 24,000 ㎡， structure plant Width(20M+14M+16M)×Lenth240M=12,000 ㎡， straight line design， all machineries are horizontal mills: The original construction of the steel plant is 24,000 square meters of land, The steel plant itself Width(20M+14M+16M)×Lenth240M=12,000 ㎡ , Inline design, all machineries are horizontal mills, contents and specifications of major equipments as on below: 1.2.1. 60TON/HR REHEATING FURNACE EQUIPMENT; 1.2.2. TYPE: PUSHER TYPE ; TOP & LOWER 3 ZONES HEATING 1.2.3. EFFECTIVE FURNACE LENGTH: 19,500 mm ; WIDTH: 6,700mm 1.2.4. FUEL: HEAVE OIL 28LITER / TON (CONTINUOUS PRODUCTION) 1.2.5. BURNER: TOP HEATING ZONE 1,800L/HR×6SET; TOP SOKING ZONE 800L/HR×3SET; LOWER

SOKING ZONE 800L/HR×3SET; TOTAL BUENER 12SET WITH PREHEATING HOT AIR 1.2.6. HOT WIND FUEL DUCT: BLOWER 150HP /590Nm3/min; RECUPERATOR: 500℃ /18,926 Nm3/min; 1.2.7. BILLET CHARGE BED 6M×2SET: CHAIN TYPE 5Mw×4,5Ml/MAX34TON/SPEED5,2M/min


6

1.2.8. BILLET CHARGE ROLLER TABLE: AC MOTOR WITH INVERTER/34Ml/ SPEED43M/min 1.2.9. MAIN PUSHEAR WITH HYDRAULIC UNIT: FORCE 47,000KG/set×2set(WORKING PRESSURE:120

kg/cm2, CYINDER: TC224mm∮ ×ST700mm ×2set) 1.2.10. SIDE PUSHEAR WITH COOLING WATER: FORCE 2,200KG (MAX), INSIDE WATER COOLING. 1.2.11.CHIMNEI SPECIFICATION: TOP ID1600mm∮ ; LOWER ID2500mm∮ ; HIGH 40Mtr. 1.2.12.BILLET: SQ100mm、 SQ120mm、 SQ130mm、 SQ150mm、 SQ160mm. 1.3.1. BREAKING DOWN MILL EQUIPMENT 3SET;

1.3.2. MAIN EQUIPMENT SPECIFICATION

ITEM NO. TYPE POWER HP GEAR RATIO ROLLER DIA REMARK BD1(K1) 2HI HORIZONVAL DC600HP 1/60.45 ∮ 650mm×600mmL 2006 TANAKA JAPAN BD2(K2) 2HI HORIZONVAL DC600HP 1/45.14 ∮ 650mm×600mmL 2006 TANAKA JAPAN BD3(K3) 2HI HORIZONVAL DC600HP 1/33.65 ∮ 650mm×600mmL 2006 TANAKA JAPAN

1.4.1. ROUGH MILL EQUIPMENT 6SET:


ITEM NO. TYPE POWER HP GEAR RATIO ROLLER DIA REMARK


7

RM1(K4) 2HI HORIZONVAL 1/28.37+1/1.7 ∮ 410mm×1000mmL 1985 TANAKA JAPAN RM2(K5) 2HI HORIZONVAL

DC600HP 1/28.37+1/1.2 ∮ 410mm×1000mmL 1985 TANAKA JAPAN

RM3(K6) 2HI HORIZONVAL 1/17.476+1/1.41 ∮ 410mm×1000mmL 1985 TANAKA JAPAN RM4(K7) 2HI HORIZONVAL

DC600HP 1/17.476+1/1.14 ∮ 410mm×1000mmL 1985 TANAKA JAPAN RM5(K8) 2HI HORIZONVAL 1/4.29+1/3.24 ∮ 410mm×1000mmL 1985 TANAKA JAPAN RM6(K9) 2HI HORIZONVAL

DC800HP 1/4.29+1/2.28 ∮ 410mm×1000mmL 1985 TANAKA JAPAN ※ WITH INLET GUIDE THROUGH & OUTLET GUIDE

1.5.1. INTERMEDIATE MILL EQUIPMENT 6SET:


ITEM NO. TYPE POWER HP GEAR RATIO ROLLER DIA REMARK IM1(K10) 2HI HORIZONVAL 1/5.39+1/1.74 ∮ 285mm×800mmL 1985 TANAKA JAPAN IM2(K11) 2HI HORIZONVAL

AC800HP 1/5.39+1/1.316 ∮ 295mm×800mmL 1985 TANAKA JAPAN

IM3(K12) 2HI HORIZONVAL 1/5.39+1/1.265 ∮ 300mm×800mmL 1985 TANAKA JAPAN IM4(K13) 2HI HORIZONVAL

AC800HP 1/5.39+1/1 ∮ 305mm×800mmL 1985 TANAKA JAPAN IM5(K14) 2HI HORIZONVAL 1/3.139 ∮ 285mm×800mmL 1985 TANAKA JAPAN IM6(K15) 2HI HORIZONVAL

AC800HP 1/2.583 ∮ 295mm×800mmL 1985 TANAKA JAPAN ※ WITH INLET GUIDE THROUGH & OUTLET GUIDE

1.6.1. FINISHING MILL EQUIPMENT 6SET: 1.6.2. MAIN EQUIPMENT SPECIFICATION ITEM NO. TYPE POWER HP GEAR RATIO ROLLER DIA REMARK


8

FM1(K16) 2HI HORIZONVAL 1/3.2 ∮ 303mm×800mmL 1985 TANAKA JAPAN FM2(K17) 2HI HORIZONVAL

DC600HP 1/2.37 ∮ 295mm×800mmL 1985 TANAKA JAPAN

FM3(K18) 2HI HORIZONVAL 1/2.179 ∮ 295mm×800mmL 1985 TANAKA JAPAN FM4(K19) 2HI HORIZONVAL

DC1,000HP 1/1.641 ∮ 285mm×800mmL 1985 TANAKA JAPAN FM5(K20) 2HI HORIZONVAL DC800HP 1/1.4 ∮ 285mm×800mmL 1985 TANAKA JAPAN FM6(K21) 2HI HORIZONVAL DC800HP 1/1.22 ∮ 295mm×800mmL 1985 TANAKA JAPAN 1.6.3. OTHER EQUIPMENT: HOT BILLET SHEAR×1SET/ HYDRAULIC TYPE、 FLYING SHEAR FOR ROUGH

MILL CUTTING HEAD×1SET / 55mmSQ/1.125M/SEC、 FLYING SHEAR FOR INTERMIDATE MILL CUTTING HEAD×1SET / 30mmSQ/4M/SEC、 PINCH ROLLER×4SET.

※ WITH INLET GUIDE THROUGH & OUTLET GUIDE ※ SPEED OF THE FINAL PRODUCT 9.5Mtr/sec FOR D12mm 1.7.1. COOLING BED EQUIPMENT 6MtrW×55MtrL: 1.7.2. MAIN EQUIPMENT SPECIFICATION 1.7.3. TYPE:4 STRANDS OPEN RUN IN ANGLE WITH BRAKE & KICK OFF SYSTEM 1.7.4. 55MtrL COOLING BED WITH FIXED RAKES、MOVING RAKES、ALIGNING ROLLERS WITH DRIVE、

CAMS DRIVE GROUP AND RUN OUT DEVICE ROLLER TABLE. 1.7.5. PRODUCT SPECIFICATION: D10∮ ～ D40∮ 1.7.6. WORKING TEMPERATURE: MAX950℃ 1.7.7. WORKING TIME: 1.85 SEC/CYCLE 1.8.1. LENTH CUTTING & FINISHING SYSTEM FOR DEFORMED BAR: 1.8.2. MAIN EQUIPMENT SPECIFICATION 1.8.3.COLD SHEAR: CUT FORCE D32×12pcs(400TON); CYCLE 15/min; BLADE SIZE 50×100×800mm; BLADE

MATERIAL SKD11; 1.8.4. LENGTH CUTTING MECHANISM: MOVING STOPER TYPE; MAX WORKING LENGTH20Mtr;


9

1.8.5. AFTER COLD SHEAR ROLLER TABLE: LENGTH20Mtr; TRANSFER SPEED 0.18M/SEC; MOTOR 3HP. 1.8.6. SMALL BUNDLE MACHINE × 4SET: HYDRAULIC TYPE; WORKING DIA/∮ 20mm～ ∮ 200mm;

WORKING SPEED: 4SEC/CYCLE; MANUFACTURER: TA TON JAPAN; MATERIAL: 3.2mm∮ WIRE ROD 1.8.7. LARGE BUNDLE MACHINE × 1SET: TYPE SUND BIRSTA SWIDEN KNSB-6/650;

WORKING DIA/∮ 300mm～ ∮ 400mm; WORKING SPEED: 7SEC/CYCLE; MATERIAL: 5.5mm∮ WIRE ROD 1.8.8. BUNDLING LINE ROLLER TABLE×4SET: CHAIN TYPE; LENGTH55Mtr×1、 16Mtr×3; MOTOR15HP×1、

10HP×4、 5HP×2、 2HP×14; TRANSFER SPEED 5M/SEC; ROLLER PICH: @1,200mm

2.1.1. PUBLIC SYSTEM EQUIPMENT:


2.1.3. COMPRESSORS: TYPE SCREW; POWER150HP×3SET/1#,8#,9#、 60HP×4SET/2#,3#,4#,5#、

100HP×2SET/6#,7#; MANUFACTURER: FUSEN TAIWAN;

2.1.4. INDIRECT WATER PUMP×4SET: VERTICAL CENTRIFUGAL TYPE FST;

MOTOR40HP/3∮ /60HZ/4P/220V; PUMP150CMH/45MH/150mmDIA

2.1.5. DIRECT WATER PUMP×4SET: HORIZONTAL CENTRIFUGAL TYPE FSBL;

MOTOR50HP/3∮ /60HZ/4P/220V; PUMP180CMH/65MH/IN125mmDIA/OUT100mmDIA

2.1.6.SCALE WATER OUTLET PUMP × 3SET: ITEM MA 、 MB 、 MC; ENERGY 25 MHEAD/2M3/MIN;

MOTOR50HP/3∮ /60HZ/4P/220V; PUMP IN125mmDIA/OUT125mmDIA

2.1.7. SCALE WATER RETURN PUMP×2SET: ITEM M43、 M44; ENERGY 25M HEAD / 5M3 / MIN;


10


2.1.8. COOLING WATER PUMP×5SET: ITEM M39、 M40 M41、 M42 M42A; ENERGY 25M HEAD/2.5M3/MIN;


2.1.9. COOLING TOWER PUMP×2SET: ITEM M47、 M48; ENERGY 25M HEAD/2.5M3/MIN;


2.1.10. E.O.T. CRANE:

A1. SPAN 18.925M / 7.5T E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN

LOADING W. (TON) 7.5 ㄨ 1.05M 18.925M SPEED (M/Min) 5.2 ㄨ 15 60 POWER (KW) 15 ㄨ 0.4×2 15 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

A2. SPAN 18.925M / 10T E.O.T. CRANE SPEC.

ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 10 ㄨ 1.595M 18.925M


11

SPEED (M/Min) 4.8 ㄨ 15 30 POWER (KW) 11 ㄨ 0.4×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 16 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

A3. SPAN 18.925M / 7.5T E.O.T. CRANE SPEC.

ITEM HOIST 1 HOIST 2 TROLLEY SPAN LOADING W. (TON) 7.5 ㄨ 0.82M 18.925M SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 ㄨ 1.1 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

B2、B3、B5 .SPAN 12.715M / 5T × 3SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN

LOADING W. (TON) 5 ㄨ 0.82M / 0 78M / 0.78M 12.715M


12

SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 / 6 / 5.5 ㄨ 0.4×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 12 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

B4、B6 SPAN 12.715M / 7.5T × 2SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN

LOADING W. (TON) 7.5 ㄨ 1.05 / 0.82M 12.715M SPEED (M/Min) 5 ㄨ 15 30 POWER (KW) 7.5 / 11 ㄨ 0.4×2 /1.5×1 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 14 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

C1 SPAN 14.695M / 5T × 1SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN

LOADING W. (TON) 5 ㄨ 0.942M 14.695M SPEED (M/Min) 8 ㄨ 15 30


13

POWER (KW) 20 ㄨ 3.75×2 5.5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 6 ㄨ WIRE DIA. 12 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996

C2、C3、C4 SPAN 14.695M / 10T × 3SET E.O.T. CRANE SPEC. ITEM HOIST 1 HOIST 2 TROLLEY SPAN

LOADING W. (TON) 7.5 ㄨ 1.6M 14.695M SPEED (M/Min) 6 / 6 / 4.8 ㄨ 15 30 POWER (KW) 15 / 15 / 11 ㄨ 0.75×1 / 0.75×1 / 0.4×2 3.75 / 3.75 / 7 5 DRIVER VOLTAGE 220 ㄨ 220 220 DRIVER FREQ.(HZ) 60 ㄨ 60 60 R.P.M 1120 ㄨ 1720 1720 BRAKE MAGNETIC ㄨ MAGNETIC MAGNETIC LIFT (M) 8 ㄨ WIRE DIA. 16 ㎜∮ ㄨ DRUM NO. 4 ㄨ MANUFACTURE SUN TRDANG TAIWAN DATE SEP.1996 3.1.1. SPARE PARTS EQUIPMENT:

3.1.2. BREAKING DOWN MILL ROLLER × 2SET / 12pcs: DIA∮ 650mm×600mmL ROLLER BEARING TYPE.

3.1.3. ROUGH MILL ROLLER × 2SET / 24pcs: DIA∮ 410mm×1,000mmL FIBER BEARING TYPE.


14

3.1.4. FIBER BEARING FOR ROUGH MILL× 2SET / 24pcs.

3.1.5. INTERMEDIATE MILL STAND WITH ROLLER、CHOCK & BEARIMG × 6SET: DIA300mm×800mmL.

3.1.6. INTERMEDIATE MILL ROLLER × 2SET / 24pcs: DIA300mm×800mmL

3.1.7. FINISHING MILL STAND WITH ROLLER、CHOCK & BEARIMG × 6SET: DIA∮ 300mm×800mmL.

3.1.8. FINISHING MILL ROLLER × 3SET / 36pcs: DIA300mm×800mmL.

3.1.9. INLET & OUTLET GUIDE × 24SET:

3.1.10. DC MOTOR × 2SET: 600HP×1SET、800HP×1SET.

3.1.11. AC MOTOR × 1SET: 800HP×1SET.

3.1.12. FLYING SHEAR FOR ROUGH MILL CUTTING HEAD: CUT FORCE MAX55mmSQ

3.1.13. FLYING SHEAR FOR INTERMEDIATE MILL CUTTING HEAD: CUT FORCE MAX35mmSQ

3.1.14. COLD SHEAR FOR LENTH CUTTING: CUT FORCE D32×12pcs(400TON)

3.1.15. 2HI PINION GEAR STAND FOR FINISHING MILL:2set

3.1.16. OTHER SPARE PARTS

3.1.17. ASSEMBLING DRAWING INCLUDE CIVIL FOUNDATION DWG.、 MACHINE ASSEMBLING DWG.

AND CABLE WIRING DWG.

TOTAL EQUIPMENT WEIGHT: 1,731,700KG


15

4.1.1.CACULATION PLAN OF MILL CAPCITY ROLLING RATE (300,000T/Y)

Products Billet Annual Production

Size Area Unit-W Size Length WeightNo.

(mm) (mm2) (kg/m) (mm) (m) (kg)

Fin. RollingSpeed

(m/sec)

Pass Time

(sec)

Pause

(sec)

Rolling Cycle Time

(sec)

ProductYield (%) (%) (T/Year)

Expected Rolling Hours

(hrs)

1 D10 78.5 0.617 130 6.0 796 11.7 110 10 5 15,000

2 D13 113.0 0.888 130 6.0 796 9.5 95 10 25 75,000

3 D16 176.7 1.387 150 6.0 1,060 7.71 95 10 20 60,000

4 D19 314.2 2.466 150 6.0 1,060 5.23 16.18 10 26.18 96 20 60,000

5 D22 380.1 2.984 150 6.0 1,060 5 15.6 10 25.6 96 5 15,000

6 D25 490.90 3.853 150 6.0 1,060 3.29 14.1 10 24.1 96 15 45,000

7 D32 804.25 5.313 150 6.0 1,060 3.29 14.1 10 24.1 96 8 24,000

8 D40 1,256 9.865 150 6.0 1,060 2.85 13 10 23 96 2 6,000

TOTAL 100 300,000 5,760


16


17

II. DESIGN BASIS 4.2.1 Product Mix and Rolling Rate

2.1.1 Product Mix: Product mix for annual production of 300,000 tons is described as the table “Calculation Plan of Mill Capacity”.

2.1.2 Rolling Rate: With regard to rolling rate, please also refer to the table “Calculation Plan of Mill Capacity”.

2.1.3 Others: Product length of bars: 12M or others

4.2.2 Billet: Continuously cast billets or hot rolled billets

Kind of steel: Low alloy steel for the manufacture of steel bars for reinforcement, rolled steel for general structure.

Section 100 ～160mmSQLength 6M ± 10 mm Weight 471～1206kg

Camber (bow): Max.20mm in 6000mm length , Rhomboidity (right angularity): Less than 3% ,Twist: Less than 1 degree per meter

Temperature of billet discharged: 1100℃～1200℃ (Engineering basis)

Note: The billet above shall have the quality suitable for final products. In order to attain high productivity, that is, improvement of

rolling efficiency and material yield, etc. which are resulted from high rolling Rate and most suitable cutting of Bar products , etc., it

should be essential to well control the billet tolerance and conditions.


18

4.2.3 Rolling Capacity 4.2.3.1 Rolling Hours Required: Rolling Hours Requires=5760 Hrs/Year

With regard to rolling hours required, please refer to the table to “Calculation Plan of Mill Capacity”. 4.2.3.2 Annual Working Hours:8 hours/shift×3 shift/day×300 day/year=7200Hr , If operating rate is 80%

Operating Rate 0.8=Rolling hour required/Annual working hour , Rolling hour required=0.8×7200=5760Hr This operating ratio is considered to be easily attained.

4.2.4 Steel Grades: The steel grades which are to be processed on the mill are as follows. a. Deformed bar: D10~D40 Steel bar , Applicable standards: JIS 20-2525＆24-2536 “Rolled steel for general structure” b. Rung bar:∮10mm～∮40mm Steel bars JIS G 3101&JIS G4051

4.2.5 Rolling Speed: Actual rolling speed: Max. 11.7 m/sec 4.2.6 Rolling Method:1. Strand rolling , Deformed bars: D10～D40mm , Rung bars :∮ 10 mm～∮40mm 4.2.7 Site (Environmental) Conditions

1) Ambient temperature: Max. 35 deg. C (more than 15℃) , Electrical control room and pulpits will be kept in 20~30℃ 2) Relative humidity: Max. 98% 3) Altitude: Less than 1,000 m above sea level

1) Electric power Normal Electric power

- Power receiving: One (1) line - Supplied power for 3set AC Motor: 3.3kv/3 phases /60HZ/2,000KW -Supplied power for 10set DC Motor: AC500v/3 phases /60/50HZ/5,600KW

- Voltage fluctuation: Within ±5% - Frequency fluctuation: Terminals of 3.3kv receiving switch and distributing panel in the electrical equipment room of the plant.


19

2) Cooling water

a. Direct Cooling Water (500 T/hr) b. Indirect Cooling Water (150 T/hr)

pH valve: 6.5 to 8.5 6.5 to 8.5

Suspended solid: Max. 20 mg/lit Max. 10 mg/lit

M-alkalinity as Ca Co3: Max. 300 mg/lit Max. 300 mg/lit

Total dissolved solids: Max. 1,500 mg/lit Max. 1,500 mg/lit

Total hardness as Ca Co3: Max. 300 mg/lit Max. 300 mg/lit

Fe: Max. 3 mg/lit Max. 2 mg/lit

Cl: Max. 200 mg/lit Max. 200 mg/lit

So4: Max. 200 mg/lit Max. 200 mg/lit

SiO2: Max. 50 mg/lit Max. 50 mg/lit

Temperature: Max. 32℃ Max. 32℃

Pressure: Max. 4 kgf/cm2 Max. 4 kgf/cm2

Design pressure: 3 kgf/ cm2 at the battery Limit of the building 3 kgf/cm2 at the battery Limit of the building


20

5.1. RM1 SCOPE OF SUPPLY SUPPLIER CUSTOMER REMARK

Country of origin ITEM NO. EQUIPMENT NAME Q’TY Supply Country Weight KG Supply

M1 60TON/HR REHEATING FURNACE M101-01 Charging BED 6MtrW×4.5MtrL CHAIN TYPE 2 s TAIWAN 19,000 M101-02 Roller Way For Charging 1set TAIWAN 12,000 34MtrL M101-03 Hyd. Unit 1 s TAIWAN 3,000 M101-04 Main Pusher 2 s TAIWAN 21,200 M101-05 Furnace (Case8MtrW×22MtrL) 1 s TAIWAN 80,000 M101-06 Hot Wind Fuel Duct 1set TAIWAN 42,000 M101-07 Recuperate 1 s TAIWAN 20,000 M101-08 Chimney 1 p TAIWAN 36,000 40MtrH M101-09 Blower With AC Motor 100HP/4P/3∮/220V 1 s TAIWAN 3,600 590N m3/min M101-10 Burner (Heating Zoon:11set + Socking Zoon:5set) 16 s TAIWAN 6,400 M101-11 H/M Control Computer 1 s TAIWAN 100 M101-12 Auto Control Panel & MCC Panel For Furnace System 1 s TAIWAN 1,600 M101-13 Oil Valve, Oil Pump, Damper, Thermocouple, Oil Flow Meter 1 s TAIWAN 3,200 M101-14 Side Pusher 1 s TAIWAN 2,200 M101-15 Roller Way For Discharging 1 s TAIWAN 6,000 18M M101-16 Day Tank for Heavy Oil With Heater3set 1 s TAIWAN 3,500 M101-17 Refractory Bricks/Blocks 1Lot ----

M1. 60TON/HR REHEATING FURNACE TOTAL WEIGHT KG. 259,800 M2 MILL MECHANCAL SECTION M201 BREAKING DOWN MILL TRAIN ROLLER BEARING M201-01 Roller Way For Furnace To Roughing Mill 1 s TAIWAN 8,000 M201-02 Pusher For Billet Feed Back 1 s TAIWAN 2,500 M201-03 Horizontal 2HI-Mill Stand With Rest Bar 3 s JAPAN 19,500 M201-04 Mill Stand Base Plates 6 s JAPAN 3,000 M201-05 Roll(∮650mm×600mmL) (Assemble In Mill Stand) 6 s TAIWAN 10,800 M201-06 Chock (Assemble In Mill Stand) 12 s TAIWAN 4,800 M201-07 Roller Bearing (Assemble In Mill Stand) 12 s JAPAN 1,500 M201-08 K1 Reducer Gear Box With Pinion Gear 1 s JAPAN 14,000 i = 1/60.45


21

SUPPLIER CUSTOMER REMARK Country of origin ITEM NO. EQUIPMENT NAME Q’TY Supply Country Weight KG Supply

M201-09 K2 Reducer Gear Box With Pinion Gear 1 s JAPAN 12,500 i = 1/45.14 M201-10 K3 Reducer Gear Box With Pinion Gear 1 s JAPAN 10,800 i = 1/33.65 M201-11 Gear Coupling (Motor - Reducer) 3 s JAPAN 2,100 M201-12 Cardan Shaft (Pinion Stand-Mill Stand) 3 s JAPAN 2,400 M201-13 Cardan Shaft Support 3 s JAPAN 1,800 M201-14 Inlet Guide Through 3 s TAIWAN 600 M201-15 Outlet Guide 2 s TAIWAN 400 M201-16 Outlet Guide & Twist Guide 1 s TAIWAN 300 M201-17 Oil Lubrication System 1 s JAPAN 3,500 M201-18 Roller Way For Roughing Mill To Intermediate Mill 1 s TAIWAN 10,000 M201-19 Hot Billet Shear 1 s JAPAN 7,500

M201 BREAKING DOWN MILL TRAIN TOTAL WEIGHT KG. 116,000 M202 ROUGHING MILL TRAIN FIBER BEARING TYPE M202-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s JAPAN 36,000 M202-02 Mill Stand Base Plates 12 s JAPAN 8,400 M202-03 Roll(∮410mm×1,000mmL) (Assemble In Mill Stand) 12 s TAIWAN 18,000 M202-04 Chock (Assemble In Mill Stand) 24 s TAIWAN 400 M202-05 Fiber Bearing (Bakelite) (Assemble In Mill Stand) 24 s TAIWAN 100 M202-06 K4 & K5 Reducer Gear Box 1st 1 s JAPAN 7,200 i=1/28.37; M202-07 K4 & K5 Reducer Gear Box 2nd 1 s JAPAN 16,000 i=1/1.7; 1/1.2 M202-08 K6 & K7 Reducer Gear Box 1st 1 s JAPAN 6,500 i=1/17.476 M202-09 K6 & K7 Reducer Gear Box 2nd 1 s JAPAN 14,500 i=1/1.41; 1/1.14 M202-10 K8 & K9 Reducer Gear Box 1st 1 s JAPAN 5,400 i=1/4.29 M202-11 K8 & K9 Reducer Gear Box 2nd 1 s JAPAN 12,000 i=1/3.24; 12.28 M202-12 Pinion Gear Box 6 s JAPAN 21,000 M202-13 Gear Coupling (Motor - Reducer1st - Reducer2nd) 12 s JAPAN 2,400 M202-14 Join Shaft (Pinion Stand-Mill Stand) 12 s TAIWAN 4,800 M202-15 Join Coupling (Pinion Stand-Mill Stand) 24 s TAIWAN 3,600 M202-16 Inlet Guide Through 6 s TAIWAN 900 M202-17 Outlet Guide Plate Case 3 s TAIWAN 500 M202-18 Outlet Guide & Twist Guide 3 s TAIWAN 900


22


M202-19 Oil Lubrication System 1 s JAPAN 4,000 M202-20 Roller Way For Roughing Mill To Intermediate Mill 1 s TAIWAN 18,000

M202 ROUGHING MILL TRAIN TOTAL WEIGHT KG. 180,600 M203 INTERMEDIATE MILL TRAIN ROLLER BEARING M203-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s JAPAN 21,000 M203-02 Mill Stand Base Plates 12 s JAPAN 3,600 M203-03 Roll(∮300mm×800mmL) (Assemble In Mill Stand) 12 s TAIWAN 4,800 M203-04 Chock (Assemble In Mill Stand) 24 s TAIWAN 4,800 M203-05 Roller Bearing (4Rows+2Trust Load)(Assemble In Mill Stand) 24 s TAIWAN 2,400 M203-06 K10 & K11 Reducer Gear Box 1st 1 s JAPAN 9,000 i=1/5.39; M203-07 K10 Reducer Gear Box 2nd 1 s JAPAN 5,800 i=1/1.74; M203-08 K11 Reducer Gear Box 2nd 1 s JAPAN 4,500 i=1/1.316; M203-09 K12 & K13 Reducer Gear Box 1st 1 s JAPAN 8,500 i=1/5.39; M203-10 K12 Reducer Gear Box 2nd 1 s JAPAN 4,200 i=1/1.265; M203-11 K13 Reducer Gear Box 2nd 1 s JAPAN 4,000 i=1/1; M203-12 K14 & K15 Reducer Gear Box 1 s JAPAN 7,200 i=1/3.139; 1/2.583 M203-13 Connecting Shaft For Gear Box 2nd 2 s JAPAN 3,000 M203-14 Pinion Gear Box 6 s JAPAN 10,800 M203-15 Gear Coupling (Motor - Reducer1st - Reducer2nd) 16 s JAPAN 3,200 M203-16 Cardan Shaft (Pinion Stand-Mill Stand) 12 s TAIWAN 3,600 M203-17 Cardan Shaft Coupling (Pinion Stand-Mill Stand) 24 s TAIWAN 2,400 M203-18 Inlet Guide Through 6 s TAIWAN 600 M203-19 Outlet Guide Plate Case 3 s TAIWAN 200 M203-20 Outlet Guide & Twist Guide 3 s TAIWAN 600 M203-21 Oil Lubrication System 1 s JAPAN 3,000 M203-22 Roller Way For Intermediate Mill To Finishing Mill 4 s TAIWAN 28,000 2Strain

M203 INTERMEDIATE MILL TRAIN TOTAL WEIGHT KG. 135,200 M204 FINISHING MILL TRAIN ROLLER BEARING TYPE M204-01 Horizontal 2HI-Mill Stand With Rest Bar 6 s JAPAN 21,000 M204-02 Mill Stand Base Plates 12 s JAPAN 3,600


23


M204-03 Roll(∮290mm×800mmL) (Assemble In Mill Stand) 12 s TAIWAN 4,800 M204-04 Chock (Assemble In Mill Stand) 24 s TAIWAN 4,800 M204-05 Roller Bearing (4Rows+2Trust Load)(Assemble In Mill Stand) 24 s TAIWAN 2,400 M204-06 K16 & K17 Reducer Gear Box 1 s JAPAN 6,800 M204-07 K18 & K19 Reducer Gear Box 1 s JAPAN 6,500 M204-08 K20 Reducer Gear Box 1 s JAPAN 3,200 M204-09 K21 Reducer Gear Box 1 s JAPAN 3,000 M204-10 Pinion Gear Box 6 s JAPAN 10,800 M204-11 Gear Coupling (Motor - Reducer) 10 s JAPAN 2,000 M204-12 Cardan Shaft (Pinion Stand-Mill Stand) 12 s TAIWAN 3,600 M204-13 Cardan Shaft Coupling (Pinion Stand-Mill Stand) 24 s TAIWAN 2,400 M204-14 Inlet Guide Through 6 s TAIWAN 500 M204-15 Outlet Guide Plate Case 3 s TAIWAN 200 M204-16 Outlet Guide & Twist Guide 3 s TAIWAN 400 M204-17 Oil Lubrication System 1 s JAPAN 3,000 M204-18 Roller Way For Intermediate Mill To Finishing Mill 2 s TAIWAN 6,000 4Strain M204-19 Flying Shear For Rough Mill Cutting Head Max:SQ55mm 1 s JAPAN 4,500 M204-20 Flying Shear For Intermediate Mill Cutting Head Max:SQ35mm 1 s JAPAN 3,500 M204-21 Pinch Roller For Final Mill 4 s JAPAN 3,200

M204 FINISHING MILL TRAIN TOTAL WEIGHT KG. 96,200 M3 PRODUCT COLLECT PACKAGE MACHINE M301 COOLING BED EQUIPMENT 6MtrW×55MtrL M301-01 4 Strands Run In Frame With Kick Of 55MtrL/PICH 1Mtr 1 s TAIWAN 55,000 M301-02 Fixed Rakes 110 p TAIWAN 16,000 M301-03 Moving Rakes 110 p TAIWAN 18,000 M301-04 Fixed Frame 11 p TAIWAN 3,000 M301-05 Moving Frame With Cams Roller Guide 22 p TAIWAN 8,000 M301-06 Cams Shaft Group With Drive Equipment & Weights Frame 24 s TAIWAN 20,000 M301-07 Aligning Rollers With Reducer Gear Motor 80 s TAIWAN 3,200 M301-08 Raise Transport For Run Out With Cam Type Drive 55 s TAIWAN 24,000


24


M301-09 Run Out Roller Table 58M/PICH 1Mtr 11 s TAIWAN 32,800 M301 COOLING BED EQUIPMENT TOTAL WEIGHT KG. 180,000

M302 LENGTH CUTTING & FINISHING SYSTEM M302-01 Cold Shear (Cut Force D32×12pcs 400Ton) 1 s JAPAN 22,000 M302-02 Length Cutting Device Max:24M/2Car 1 s JAPAN 35,000 M302-03 Roller Table 24MtrL/PICH 1MtrL 1 s TAIWAN 12,000 M302-04 Product Transfer(Type : Chain Traversing) 24MtrL 1 s TAIWAN 36,000 M302-05 Auto Binding Machine TYPE:ASV20 4 s JAPAN 10,200 DATON JAPAN M302-06 Transfer Roller Table 1 s JAPAN 18,200 TANAKA JAPAN M302-07 Auto Bundling Machine SUND BIRSTA KNSB 6/650 1 s SWIDEN 2,600 SUND SWIDEN M302-08 Product Transfer Roller Table 3 s TAIWAN 50,000 M302-09 Transportation Machine (Type : Chain Traversing) 1 s TAIWAN 21,000 M302-10 2 s TAIWAN 3,000

M302 LENGTH CUTTING & FINISHING SYSTEM EQUIPMENT TOTAL WEIGHT KG. 210,000 E1 POWER RECEIVING & DISTRIBUTION SYSTEM E101-01 DC Motors 600HP/600V/650～1,300rpm For Breaking Down 3 s TAIWAN 17,400 E101-02 DC Motors 600HP/600V/650～1,300rpm For Rough Mill 2 s TAIWAN 11,600 E101-03 DC Motors 800HP/600V/650～1,300rpm For Rough Mill 1 s TAIWAN 6,800 E101-04 AC Motors 800HP/3,300V/12P/580r.p.m For Intermediate 3 s TAIWAN 19,500 E101-05 DC Motors 600HP/600V/650～1,300rpm For Finishing Mill 1 s TAIWAN 5,800 E101-06 DC Motors 1,000HP/600V/650～1,300rpm For Finishing Mill 1 s TAIWAN 8,200 E101-07 DC Motors 800HP/600V/650～1,300rpm For Finishing Mill 2 s TAIWAN 13,600 E101-08 DC Motors 600HP On/Off Panel & Control Panel 3 s TAIWAN 1,800 E101-09 DC Motors 600HP On/Off Panel & Control Panel 2 s TAIWAN 1,200 E101-10 DC Motors 800HP On/Off Panel & Control Panel 1 s TAIWAN 600 E101-11 AC Motors 800HP On/Off Panel & Control Panel 3 s TAIWAN 1,800 E101-12 DC Motors 600HP On/Off Panel & Control Panel 1 s TAIWAN 600 E101-13 DC Motors 1,000HP On/Off Panel & Control Panel 1 s TAIWAN 600 E101-14 DC Motors 800HP On/Off Panel & Control Panel 2 s TAIWAN 1,200


25


E101-15 11.4KV Electric Receive Equipment 5 s TAIWAN 3,000 E101-16 Transformer 2.0MVA/11.4KV-550V For Breaking Down 1 s TAIWAN 6,500 E101-17 Transformer 2.0MVA/11.4KV-550V For Rough Mill 1 s TAIWAN 6,500 E101-18 Transformer 2.5MVA/11.4KV-3,300V For Intermediate 1 s TAIWAN 7,800 E101-19 Transformer 3.0MVA/11.4KV-550V For Finishing Mill 1 s TAIWAN 8,500 E101-20 Transformer 1.0MVA/11.4KV-440V/220V/110V 1 s TAIWAN 5,200 E101-21 Operating Desk 4 s TAIWAN 400 E101-22 Auto Control Panel & MCC Panel For Furnace System 1 s TAIWAN 2,000 E101-23 Sensor Control-Photocell 1 s TAIWAN 200 E101-24 Auto Control Panel & MCC Panel For Product Collect Package 1 s TAIWAN 2,400 E101-25 MCC Panel For Public System 1 s TAIWAN 1,600 E101-26 H/M Control Computer 1 s TAIWAN 200

E1 POWER RECEIVING & DISTRIBUTION SYSTEM TOTAL WEIGHT KG. 135,000 P1 PUBLIC SYSTEM EQUIPMENT P101 AIR COMPRESSORS SYSTEM P101-01 150HP Compressors Screw Type FUSEN TAIWAN 3 s TAIWAN 6,000 NO.1#,8#,9# P101-02 60HP Compressors Screw Type FUSEN TAIWAN 4 s TAIWAN 4,800 NO.2#,3#,4#,5# P101-03 100HP Compressors Screw Type FUSEN TAIWAN 2 s TAIWAN 3,600 NO.6#,7# P101-04 Receiver Tank 3 s TAIWAN 4,800 P101-05 Refrigerated Air Dryer 3 s TAIWAN 1,800 P102 WATER SYSTEM PUMP P102-01 Indirect Water Pump 40HP/60HZ/3∮/220V 4 s TAIWAN 3,200 P102-02 Direct Water Pump 50HP/60HZ/3∮/220V 4 s TAIWAN 3,600 P102-03 Scale Water Outlet Pump 50HP/60HZ/3∮/220V 3 s TAIWAN 2,700 NO.MA,MB,MC P102-04 Scale Water Return Pump 50HP/60HZ/3∮/220V 2 s TAIWAN 1,800 NO.M43,M44 P102-05 Cooling Water Return Pump 25HP/60HZ/3∮/220V 5 s TAIWAN 2,000 M39,M40,M41,M42,M42A P102-06 Cooling Tower Pump 20HP/60HZ/3∮/220V 2 s TAIWAN 800 NO.M47,M48 P103 E.O.T. CRANE P103-01 A1. Span 18.925M / 7.5Ton E.O.T. Crane 1 s TAIWAN 14,000 P103-02 A2. Span 18.925M / 10Ton E.O.T. Crane 1 s TAIWAN 16,000


26


P103-03 A3. Span 18.925M / 7.5Ton E.O.T. Crane 1 s TAIWAN 14,000 P103-04 B2、B3、B5 .Span 12.715M / 5Ton E.O.T. Crane 3 s TAIWAN 18,000 P103-05 B4、B6、Span 12.715M / 7.5Ton E.O.T. Crane 2 s TAIWAN 15,000 P103-06 C1 Span 14.695M / 5Ton E.O.T. Crane 1 s TAIWAN 5,500 P103-07 C2、C3、C4 Span 14.695M / 10Ton E.O.T. Crane 3 s TAIWAN 24,000

P1 PUBLIC SYSTEM EQUIPMENT TOTAL WEIGHT KG. 141,600 S1 SPARE PARTS EQUIPMENT S101-01 Spare Blower With AC Motor 100HP/4P/3∮/220V 1 s TAIWAN 3,600 590N m3/min S101-02 Spare Recuperate 1 s TAIWAN 20,000 S101-03 Spare Roller For Breaking Down Mill DIA∮650mm×600mmL 12 p TAIWAN 21,600 6pcs With Chock S101-04 Spare Roller For Rough Mill DIA∮410mm×1,000mmL 24 p TAIWAN 36,000 S101-05 Spare Fiber Bearing For Rough Mill 24 p TAIWAN 200 S101-06 Spare Stand With Roller & Chock For Intermediate Mill 6 s TAIWAN 30,000 S101-07 Spare Roller For Intermediate Mill DIA∮300mm×800mmL 24 p TAIWAN 12,000 12pcs With Chock S101-08 Spare Stand With Roller & Chock For Finishing Mill 6 s TAIWAN 30,000 S101-09 Spare Roller For Finishing Mill DIA∮300mm×800mmL 36 p TAIWAN 18,000 12pcs With Chock S101-10 Spare Inlet Guide、Outlet Guide Plate、Outlet Twist Guide 24 s TAIWAN 3,000 S101-11 Spare DC Motors 600HP/600V/650～1,300rpm 1 s TAIWAN 5,800 S101-12 Spare DC Motors 800HP/600V/650～1,300rpm 1 s TAIWAN 6,800 S101-13 Spare AC Motors 800HP/3,300V/12P/580r.p.m 1 s TAIWAN 6,500 S101-14 Spare Flying Shear For Rough Mill Max:SQ55mm 1 s JAPAN 4,500 S101-15 Spare Flying Shear For Intermediate Mill Max:SQ35mm 1 s JAPAN 3,500 S101-16 Spare Cold Shear (Cut Force D32×12pcs 400Ton) 1 s JAPAN 22,000 S101-17 Spare 2HI Pinion Gear Box 2 s JAPAN 3,600 S101-18 Other Spare Parts 1 s TAIWAN 50,000

S101-19 Assembling Drawing (Include : Civil Foundation DWG、Machine Assembling DWG. And Cable Wiring DWG.) 1 s TAIWAN 200

S1 SPARE PARTS EQUIPMENT TOTAL WEIGHT KG. 277,300 SUB. SUPPLY TOTAL WEIGHT KG. 1,731,700

300,000TON/YEAR USED BAR ROLLING MILL PLANE

-27-

50TON/HR ROLLING MILL


-28-


-29-


-30-


-31-


-32-


-33-


-34-


-35-


-36-


-37-


-38-


-39-


-40-


-41-


-42-


-43-


-44-


-45-


-46-


-47-


-48-


-49-


-50-


-51-


-52-


-53-


-54-


-55-


-56-


-57-


-58-


-59-


-60-


-61-

300,000TON/YEAR USED STEEL BAR ROLLING MILL · 300,000ton/year used steel bar rolling mill 6 1.2.8....

Documents

Transcript of 300,000TON/YEAR USED STEEL BAR ROLLING MILL · 300,000ton/year used steel bar rolling mill 6 1.2.8....