3 Review Production of Electricty Using Brakes
-
Upload
deepurocks10 -
Category
Documents
-
view
224 -
download
0
Transcript of 3 Review Production of Electricty Using Brakes
-
8/11/2019 3 Review Production of Electricty Using Brakes
1/14
G U I D E D B Y : -
PROF. O Y Y A R A V E L U R
PRODUCTION OF ELECTRICTY
USING BRAKES
NAME OF STUDENTS:-SARTHAK CHUGH 10BME0214
NAMAN JAIN 10BME0476RAGHAV SHARMA 10BME0207
REVIEWER:-Prof. SIVACHITTRAMBALAM
HARDWARE PROJECT
(REVIEW ONE)
-
8/11/2019 3 Review Production of Electricty Using Brakes
2/14
CONTENTS
Abstract
Introduction
Work done so far
Results and discussions Conclusions
References
-
8/11/2019 3 Review Production of Electricty Using Brakes
3/14
ABSTRACT (Objective)
To increase an electric car efficiency.
Here we are mainly concentrating on converting thewaste energy into considerable electric energy.
instead of friction energy used to apply brakes,backforce of dynamo can be used.
-
8/11/2019 3 Review Production of Electricty Using Brakes
4/14
INTRODUCTION(Literature review)
Whenever brakes will be applied a shaft will come incontact with the axel and transfer the energy to agear system which increases its RPM which is furtherconnected to a flywheel. This flywheel is connectedto a dynamo. Due to rotation dynamo will produceelectricity and it applies some backward force which
will be used to stop the vehicle.
The electricity produced by the dynamo can be usedto charge a battery.
-
8/11/2019 3 Review Production of Electricty Using Brakes
5/14
WORK DONE SO FAR (Review 1)
The initial step is to design the car and to collect allthe parts accordingly.
Car design is completed.
We have purchased chassis and wire. The second step is to get appropriate gear and
flywheel.
-
8/11/2019 3 Review Production of Electricty Using Brakes
6/14
Review 2
Had purchased appropriate gears.
We had designed the model of our moving shaft.
The shaft is designed in such a way so that the disc,
attached to it help the shaft to rotate and it can moveto and fro in perpendicular direction.
The assembly is shown n the next slide.
We had purchased axel, gears, chassis, dynamo.
-
8/11/2019 3 Review Production of Electricty Using Brakes
7/14
-
8/11/2019 3 Review Production of Electricty Using Brakes
8/14
Review 3
The electricity is produced when brakes are applied.
The electricity produced can enlighten aroundenough LEDs at a time at only 80-100 RPM.
At 200 RPM of disc rotation 12V of potentialdifference is obtained.
The backforce on dynamo depends upon theresistance connected to the dynamo.
15 LEDs are connected in parallel.
-
8/11/2019 3 Review Production of Electricty Using Brakes
9/14
WORKING (SHAFT)
Force is applied on the bearing
Bearing is fixed with the shaft, connected to the disc
When bearing moves disc will move and comes in
contact with the disc 2 Energy is transferred to the dynamo.
Spring will help it in disengaging the disc1 withdisc2.
-
8/11/2019 3 Review Production of Electricty Using Brakes
10/14
RESULTS AND DISCUSSION
Dynamo is producing electricity after considerableRPM which can be used to charge the battery.
When brakes are applied the electricity is produced .
Spring will pull the disc when brakes are releasedand conversion of energy will stop.
The electricity produced by the dynamo is used tcharge the battery.
The battery is recharged thus the efficiency of anelectric car get increased.
-
8/11/2019 3 Review Production of Electricty Using Brakes
11/14
ADVANCED MECHANISM
We can apply ABS system and automatic gear box in it.
The automatic gear system will change the gears according tothe torque supplied by the disc and its RPM.
If the person will apply full brakes the flywheel will apply
enough inertia so that the car will stop suddenly but at thesame time ABS system will decrease the friction between thedisc 1 and disc 2 so that the wheel will not slip on the road.
The gear box will engage the gear according to the RPM atwhich the disc will rotate.
With both of these technologies we need to have frictionbrakes too so that they will stop the car if the electric brakingsystem not works.
-
8/11/2019 3 Review Production of Electricty Using Brakes
12/14
Result
The cost of the apparatus is quite low so it can beattached in any car or vehicle.
Efficiency of an electric car can be increased upto30%.
Waste heat energy is used.
Efficiency can also be used by attaching automaticgears after the pulley.
-
8/11/2019 3 Review Production of Electricty Using Brakes
13/14
CONCLUSION
The electricity produced can be used to charge thebattery of the car and it can be reused. The efficiencyof an electric car is increased considerably.
-
8/11/2019 3 Review Production of Electricty Using Brakes
14/14
References
www.Google.com
www.Aliexpress.com
www.Howstuffworks.com
www.ncert.nic.in(journals and student project)
http://www.google.com/http://www.aliexpress.com/http://www.howstuffworks.com/http://www.ncert.nic.in/http://www.ncert.nic.in/http://www.howstuffworks.com/http://www.aliexpress.com/http://www.google.com/